ZARLINK MVTX2603

MVTX2603
Unmanaged 24-Port 10/100 Mb + 2-Port 1 Gb
Ethernet Switch
Data Sheet
February 2004
Features
•
•
•
•
•
•
Ordering Information
Integrated Single-Chip 10/100/1000 Mbps
Ethernet Switch
24 10/100 Mbps Autosensing, Fast Ethernet
Ports with RMII or Serial Interface (7WS)
2 Gigabit Ports with GMII, PCS, 10/100 and
stacking (2 G per port) interface options per port
Serial interface for configuration
Supports two Frame Buffer Memory domains with
SRAM at 100 MHz
Supports memory size 2 MB, or 4 MB
MVTX2603AG
-40°C to +85°C
•
•
• For 24+2, two SRAM domains (2 MB or 4 MB) are
required.
• For 24+2 stacking (2 G per stacking port), two ZBT
domains (2 MB or 4 MB) are required.
•
•
Supports per-system option to enable flow control
for best effort frames even on QoS-enabled ports
Load sharing among trunked ports can be based
on source MAC and/or destination MAC. The
Gigabit trunking group has one more option,
based on source port.
Port Mirroring to a dedicated port or port 23
Built-in reset logic triggered by system
malfunction
I2C EEPROM for configuration
Traffic Classification
• 4 transmission priorities for Fast Ethernet ports with 2
dropping levels
• Classification based on:
- Port based priority
- VLAN Priority field in VLAN tagged frame
VLAN 1 MCT
•
•
•
•
•
Applies centralized shared memory architecture
Up to 64K MAC addresses
Maximum throughput is 6.4 Gbps non-blocking
High performance packet forwarding (19.047 M
packets per second) at full wire speed
Full Duplex Ethernet IEEE 802.3x Flow Control
Backpressure flow control for Half Duplex ports
Supports Ethernet multicasting and broadcasting
and flooding control
VLAN 1 MCT
•
•
•
•
553 Pin HSBGA
Frame Data Buffer A
SRAM (1 M / 2 M)
Frame Data Buffer B
SRAM (1 M / 2 M)
FDB Interface
FCB
Search
Engine
Frame Engine
24 x 10 /100
RMII
Ports 0 - 23
GMII/
PCS
Port
24
LED
GMII/
PCS
Port
25
Management
Module
MCT
Link
Parallel/
Serial
Figure 1 - MVTX2603 System Block Diagram
1
Zarlink Semiconductor Inc.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright 2003-2004, Zarlink Semiconductor Inc. All Rights Reserved.
MVTX2603
Data Sheet
- DS/TOS field in IP packet
- UDP/TCP logical ports: 8 hard-wired and 8 programmable ports, including one programmable range
• The precedence of the above classifications is programmable
•
QoS Support
• Supports IEEE 802.1p/Q Quality of Service with 4 transmission priority queues with delay bounded, strict priority, and
WFQ service disciplines
• Provides 2 levels of dropping precedence with WRED mechanism
• User controls the WRED thresholds
• Buffer management: per class and per port buffer reservations
• Port-based priority: VLAN priority in a tagged frame can be overwritten by the priority of Port VLAN ID.
•
•
•
•
•
3 port trunking groups, one for the 2 Gigabit ports, and two groups for 10/100 ports, with up to 4 10/100
ports per group
Full set of LED signals provided by a serial interface or 6 LED signals dedicated to Gigabit port status only
(without serial interface)
Hardware auto-negotiation through serial management interface (MDIO) for Ethernet ports
Hardware auto-negotiation through serial management interface (MDIO) for Ethernet ports
Built-In Self Test for internal and external SRAM
Description
The MVTX2603 is a high density, low cost, high performance, non-blocking Ethernet switch chip. A single chip
provides 24 ports at 10/100 Mbps, 2 ports at 1000 Mbps. The Gigabit ports can also support 10/100 M and 2 G
stacking modes.
The chip supports up to 64 K MAC addresses. The centralized shared memory architecture permits a very high
performance packet forwarding rate at up to 9.524 M packets per second at full wire speed. The chip is optimized to
provide low-cost, high-performance workgroup switching.
Two Frame Buffer Memory domains utilize cost-effective, high-performance synchronous SRAM with aggregate
bandwidth of 12.8 Gbps to support full wire speed on all ports simultaneously. In the 24+2 stacking (2 G per
stacking port) configuration, 2 ZBT domains are needed.
With delay bounded, strict priority, and/or WFQ transmission scheduling and WRED dropping schemes, the
MVTX2603 provides powerful QoS functions for various multimedia and mission-critical applications. The chip
provides 4 transmission priorities (8 priorities per Gigabit port) and 2 levels of dropping precedence. Each packet is
assigned a transmission priority and dropping precedence based on the VLAN priority field in a VLAN tagged
frame, or the DS/TOS field, or the UDP/TCP logical port fields in IP packets. The MVTX2603 recognizes a total of
16 UDP/TCP logical ports, 8 hard-wired and 8 programmable (including one programmable range).
The MVTX2603 supports 3 groups of port trunking/load sharing. One group is dedicated to the two Gigabit ports
and the other two groups to 10/100 ports, where each 10/100 group can contain up to 4 ports. Port trunking/load
sharing can be used to group ports between interlinked switches to increase the effective network bandwidth.
In half-duplex mode, all ports support backpressure flow control, to minimize the risk of losing data during long
activity bursts. In full-duplex mode, IEEE 802.3x flow control is provided. The MVTX2603 also supports a persystem option to enable flow control for best effort frames even on QoS-enabled ports.
The Physical Coding Sublayer (PCS) is integrated on-chip to provide a direct 10-bit interface for connection to
SERDES chips. The PCS can be bypassed to provide a GMII interface.
The MVTX2603 is fabricated using 0.25 micron technology. Inputs, however, are 3.3 V tolerant, and the outputs are
capable of directly interfacing to LVTTL levels. The MVTX2603 is packaged in a 553-pin Ball Grid Array package.
2
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
Table of Contents
1.0 Block Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.1 Frame Data Buffer (FDB) Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.2 GMII/PCS MAC Module (GMAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.3 Physical Coding Sublayer (PCI) Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.4 10/100 MAC Module (RMAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.5 Configuration Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.6 Frame Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.7 Search Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.8 LED Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.9 Internal Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.0 System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.1 Configuration Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2 I2C Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2.1 Start Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.2.2 Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.2.3 Data Direction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.2.4 Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.2.5 Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.2.6 Stop Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.3 Synchronous Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.3.1 Write Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.3.2 Read Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.4 Stacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.0 MVTX2603 Data Forwarding Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.1 Unicast Data Frame Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.2 Multicast Data Frame Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.0 Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.2 ZBT Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.3 Detailed Memory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.4 Memory Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.0 Search Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.1 Search Engine Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.2 Basic Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.3 Search, Learning, and Aging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.3.1 MAC Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.3.2 Learning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.3.3 Aging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.4 Quality of Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.5 Priority Classification Rule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.6 Port Based VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.7 Memory Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.0 Frame Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.1 Data Forwarding Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.2 Frame Engine Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.2.1 FCB Manager. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.2.2 Rx Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.2.3 RxDMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.2.4 TxQ Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.3 Port Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6.4 TxDMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
Table of Contents
7.0 Quality of Service and Flow Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
7.1 Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
7.2 Four QoS Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
7.3 Delay Bound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
7.4 Strict Priority and Best Effort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
7.5 Weighted Fair Queuing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
7.6 Shaper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
7.7 WRED Drop Threshold Management Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
7.8 Buffer Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
7.8.1 Dropping When Buffers Are Scarce . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
7.9 MVTX2603 Flow Control Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
7.9.1 Unicast Flow Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
7.9.2 Multicast Flow Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
7.10 Mapping to IETF Diffserv Classes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
8.0 Port Trunking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
8.1 Features and Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
8.2 Unicast Packet Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
8.3 Multicast Packet Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
8.4 Trunking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
9.0 Port Mirroring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
9.1 Port Mirroring Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
9.2 Setting Registers for Port Mirroring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
10.0 TBI Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
11.0 GPSI (7WS) Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
11.1 GPSI Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
11.2 SCAN LINK and SCAN COL interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
12.0 LED Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
12.1 LED Interface Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
12.2 Port Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
12.3 LED Interface Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
13.0 Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
13.1 MVTX2603 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
13.2 Group 0 Address MAC Ports Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
13.2.1 ECR1Pn: Port N Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
13.2.2 ECR2Pn: Port N Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
13.2.3 GGControl – Extra GIGA Port Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
13.3 Group 1 Address VLAN Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
13.3.1 AVTCL – VLAN Type Code Register Low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
13.3.2 AVTCH – VLAN Type Code Register High . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
13.3.3 PVMAP00_0 – Port 00 Configuration Register 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
13.3.4 PVMAP00_1 – Port 00 Configuration Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
13.3.5 PVMAP00_2 – Port 00 Configuration Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
13.3.6 PVMAP00_3 – Port 00 Configuration Register 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
13.4 Port Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
13.4.1 PVMODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
13.4.2 TRUNK0_MODE– Trunk group 0 mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
13.4.3 TRUNK1_MODE – Trunk group 1 mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
13.5 Group 4 Address Search Engine Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
13.5.1 TX_AGE – Tx Queue Aging timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
13.5.2 AGETIME_LOW – MAC address aging time Low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
13.5.3 AGETIME_HIGH –MAC address aging time High . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
4
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
Table of Contents
13.5.4 SE_OPMODE – Search Engine Operation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
13.6 Group 5 Address Buffer Control/QOS Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
13.6.1 FCBAT – FCB Aging Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
13.6.2 QOSC – QOS Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
13.6.3 FCR – Flooding Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
13.6.4 AVPML – VLAN Priority Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
13.6.5 AVPMM – VLAN Priority Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
13.6.6 AVPMH – VLAN Priority Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
13.6.7 TOSPML – TOS Priority Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
13.6.8 TOSPMM – TOS Priority Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
13.6.9 TOSPMH – TOS Priority Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
13.6.10 AVDM – VLAN Discard Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
13.6.11 TOSDML – TOS Discard Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
13.6.12 BMRC - Broadcast/Multicast Rate Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
13.6.13 UCC – Unicast Congestion Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
13.6.14 MCC – Multicast Congestion Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
13.6.15 PR100 – Port Reservation for 10/100 ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
13.6.16 PRG – Port Reservation for Giga ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
13.6.17 SFCB – Share FCB Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
13.6.18 C2RS – Class 2 Reserve Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
13.6.19 C3RS – Class 3 Reserve Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
13.6.20 C4RS – Class 4 Reserve Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
13.6.21 C5RS – Class 5 Reserve Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
13.6.22 C6RS – Class 6 Reserve Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
13.6.23 C7RS – Class 7 Reserve Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
13.6.24 Classes Byte Limit Set 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
13.6.25 Classes Byte Limit Set 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
13.6.26 Classes Byte Limit Set 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
13.6.27 Classes Byte Limit Set 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
13.6.28 Classes Byte Limit Giga Port 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
13.6.29 Classes Byte Limit Giga Port 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
13.6.30 Classes WFQ Credit Set 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
13.6.31 Classes WFQ Credit Set 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
13.6.32 Classes WFQ Credit Set 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
13.6.33 Classes WFQ Credit Set 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
13.6.34 Classes WFQ Credit Port G1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
13.6.35 Classes WFQ Credit Port G2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
13.6.36 Class 6 Shaper Control Port G1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
13.6.37 Class 6 Shaper Control Port G2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
13.6.38 RDRC0 – WRED Rate Control 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
13.6.39 RDRC1 – WRED Rate Control 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
13.6.40 User Defined Logical Ports and Well Known Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
13.6.40.1 USER_PORT0_(0~7) – User Define Logical Port (0~7). . . . . . . . . . . . . . . . . . . . . . . . . . . 62
13.6.40.2 USER_PORT_[1:0]_PRIORITY - User Define Logic Port 1 and 0 Priority . . . . . . . . . . . . . 63
13.6.40.3 USER_PORT_[3:2]_PRIORITY - User Define Logic Port 3 and 2 Priority . . . . . . . . . . . . . 63
13.6.40.4 USER_PORT_[5:4]_PRIORITY - User Define Logic Port 5 and 4 Priority . . . . . . . . . . . . . 63
13.6.40.5 USER_PORT_[7:6]_PRIORITY - User Define Logic Port 7 and 6 Priority . . . . . . . . . . . . . 63
13.6.40.6 USER_PORT_ENABLE [7:0] – User Define Logic 7 to 0 Port Enables . . . . . . . . . . . . . . . 63
13.6.40.7 WELL_KNOWN_PORT [1:0] PRIORITY- Well Known Logic Port 1 and 0 Priority . . . . . . 64
13.6.40.8 WELL_KNOWN_PORT [3:2] PRIORITY- Well Known Logic Port 3 and 2 Priority . . . . . . 64
13.6.40.9 WELL_KNOWN_PORT [5:4] PRIORITY- Well Known Logic Port 5 and 4 Priority . . . . . . 64
13.6.40.10 WELL_KNOWN_PORT [7:6] PRIORITY- Well Known Logic Port 7 and 6 Priority . . . . . 64
5
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
Table of Contents
13.6.40.11 WELL KNOWN_PORT_ENABLE [7:0] – Well Known Logic 7 to 0 Port Enables. . . . . . . 65
13.6.40.12 RLOWL – User Define Range Low Bit 7:0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
13.6.40.13 RLOWH – User Define Range Low Bit 15:8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
13.6.40.14 RHIGHL – User Define Range High Bit 7:0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
13.6.40.15 RHIGHH – User Define Range High Bit 15:8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
13.6.40.16 RPRIORITY – User Define Range Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
13.7 Group 6 Address MISC Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
13.7.1 MII_OP0 – MII Register Option 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
13.7.2 MII_OP1 – MII Register Option 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
13.7.3 FEN – Feature Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
13.7.4 MIIC0 – MII Command Register 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
13.7.5 MIIC1 – MII Command Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
13.7.6 MIIC2 – MII Command Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
13.7.7 MIIC3 – MII Command Register 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
13.7.8 MIID0 – MII Data Register 0. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
13.7.9 MIID1 – MII Data Register 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
13.7.10 LED Mode – LED Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
13.7.11 CHECKSUM - EEPROM Checksum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
13.8 Group 7 Address Port Mirroring Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
13.8.1 MIRROR1_SRC – Port Mirror source port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
13.8.2 MIRROR1_DEST – Port Mirror destination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
13.8.3 MIRROR2_SRC – Port Mirror source port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
13.8.4 MIRROR2_DEST – Port Mirror destination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
13.9 Group F Address CPU Access Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
13.9.1 GCR-Global Control Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
13.9.2 DCR-Device Status and Signature Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
13.9.3 DCR1-Giga port status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
13.9.4 DPST – Device Port Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
13.9.5 DTST – Data read back register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
13.9.6 PLLCR - PLL Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
13.9.7 LCLK - LA_CLK delay from internal OE_CLK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
13.9.8 OECLK - Internal OE_CLK delay from SCLK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
13.9.9 DA – DA Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
13.10 TBI Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
13.10.1 Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
13.10.2 Status Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
13.10.3 Advertisement Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
13.10.4 Link Partner Ability Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
13.10.5 Expansion Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
13.10.6 Extended Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
14.0 BGA and Ball Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
14.1 BGA Views (Top-View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
14.1.1 Encapsulated View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
14.2 Ball – Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
14.2.1 Ball Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
14.3 Ball – Signal Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
14.4 AC/DC Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
14.4.1 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
14.4.2 DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
14.4.3 Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
14.4.4 Typical Reset & Bootstrap Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
14.5 Local Frame Buffer SBRAM Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
6
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
Table of Contents
14.5.1 Local SBRAM Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
14.6 Local Switch Database SBRAM Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
14.6.1 Local SBRAM Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
14.7 AC Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
14.7.1 Reduced Media Independent Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
14.7.2 Gigabit Media Independent Interface - Port A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
14.7.3 Ten Bit Interface - Port A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
14.7.4 Gigabit Media Independent Interface - Port B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
14.7.5 Ten Bit Interface - Port B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
14.7.6 LED Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
14.7.7 SCANLINK SCANCOL Output Delay Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
14.7.8 MDIO Input Setup and Hold Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
14.7.9 I2C Input Setup Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
14.7.10 Serial Interface Setup Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
7
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
List of Figures
Figure 1 - MVTX2603 System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Figure 2 - Data Transfer Format for I2C Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 3 - Write Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 4 - Read Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 5 - MVTX2603 SRAM Interface Block Diagram (DMAs for 10/1000 Ports Only) . . . . . . . . . . . . . . . . . . . . 15
Figure 6 - Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 7 - Priority Classification Rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 8 - Memory Configuration For: 2 Banks, 1 Layer, 2 MB Total . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 9 - Memory Configuration For: 2 Banks, 2 Layer, 4 MB Total . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 10 - Memory Configuration For: 2 Banks, 1 Layer, 4 MB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 11 - Memory Configuration For: 2 Banks, 2 Layers, 4 MB Total . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 12 - Memory Configuration For: 2 Banks, 1 Layer, 4 MB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 13 - Buffer Partition Scheme Used to Implement MVTX2603 Buffer Management . . . . . . . . . . . . . . . . . . 30
Figure 14 - TBI Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 15 - GPSI (7WS) Mode Connection Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Figure 16 - SCAN LINK and SCAN COLLISON Status Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Figure 17 - Timing Diagram of LED Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 18 - Typical Reset & Bootstrap Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Figure 19 - Local Memory Interface – Input Setup and Hold Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Figure 20 - Local Memory Interface - Output Valid Delay Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Figure 21 - Local Memory Interface – Input Setup and Hold Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Figure 22 - Local Memory Interface - Output Valid Delay Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Figure 23 - AC Characteristics – Reduced Media Independent Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Figure 24 - AC Characteristics – Reduced Media Independent Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Figure 25 - AC Characteristics- GMII . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Figure 26 - AC Characteristics – Gigabit Media Independent Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Figure 27 - Gigabit TBI Interface Transmit Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Figure 28 - Gigabit TBI Interface Receive Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Figure 29 - AC Characteristics- GMII . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Figure 30 - AC Characteristics – Gigabit Media Independent Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Figure 31 - Gigabit TBI Interface Transmit Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Figure 32 - Gigabit TBI Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Figure 33 - AC Characteristics – LED Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Figure 34 - SCANLINK SCANCOL Output Delay Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Figure 35 - SCANLINK, SCANCOL Setup Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Figure 36 - MDIO Input Setup and Hold Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Figure 37 - MDIO Output Delay Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Figure 38 - I2C Input Setup Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Figure 39 - I2C Output Delay Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Figure 40 - Serial Interface Setup Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Figure 41 - Serial Interface Output Delay Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
8
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
List of Tables
Table 1 - Memory Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Table 2 - PVMAP Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Table 3 - Supported Memory Configurations (Pipeline SBRAM Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Table 4 - Supported Memory Configurations (ZBT Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Table 5 - Options for Memory Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Table 6 - Two-dimensional World Traffic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 8 - Four QoS Configurations for a Gigabit Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Table 7 - Four QoS Configurations for a 10/100 Mbps Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Table 9 - WRED Drop Thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 10 - Mapping between MVTX2603 and IETF Diffserv Classes for Gigabit Ports . . . . . . . . . . . . . . . . . . . . . 32
Table 11 - Mapping between MVTX2603 and IETF Diffserv Classes for 10/100 Ports . . . . . . . . . . . . . . . . . . . . . 32
Table 12 - MVTX2603 Features Enabling IETF Diffserv Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Table 13 - Reset & Bootstrap Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Table 14 - AC Characteristics – Local Frame Buffer SBRAM Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Table 15 - AC Characteristics – Local Switch Database SBRAM Memory Interface . . . . . . . . . . . . . . . . . . . . . . . 98
Table 16 - AC Characteristics – Reduced Media Independent Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Table 17 - AC Characteristics – Gigabit Media Independent Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Table 18 - Output Delay Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Table 19 - Input Setup Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Table 20 - AC Characteristics – Gigabit Media Independent Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Table 21 - Output Delay Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Table 22 - Input Setup Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Table 23 - AC Characteristics – LED Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Table 24 - SCANLINK, SCANCOL Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Table 25 - MDIO Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Table 26 - I2C Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Table 27 - Serial Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
9
Zarlink Semiconductor Inc.
MVTX2603
1.0
Block Functionality
1.1
Frame Data Buffer (FDB) Interfaces
Data Sheet
The FDB interface supports pipelined synchronrous burst SRAM (SBRAM) memory at 100 MHz. To ensure a nonblocking switch, two memory domains are required. Each domain has a 64 bit wide memory bus. At 100 MHz, the
aggregate memory bandwidth is 12.8 Gbps, which is enough to support 24 10/100 Mbps and 2 Gigabit ports at full
wire speed switching. For 24+ 2 stacking application, ZBT memory at 125 MHz is required.
The Switching Database is also located in the external SBRAM; it is used for storing MAC addresses and their
physical port number. It is duplicated and stored in both memory domains. Therefore, when the system updates the
contents of the switching database, it has to write the entry to both domains at the same time.
1.2
GMII/PCS MAC Module (GMAC)
The GMII/PCS Media Access Control (MAC) module provides the necessary buffers and control interface between
the Frame Engine (FE) and the external physical device (PHY).
The MVTX2603 GMAC implements both GMII and MII interfaces, which offers a simple migration from 10/100 to
1 G. The GMAC of the MVTX2603 meets the IEEE 802.3Z specification. It is able to operate in 10 M/100 M either
Half or Full Duplex mode with a back pressure/flow control mechanism or in 1 G full duplex mode with flow control
mechanism. Furthermore, it will automatically retransmit upon collision for up to 16 total transmissions. PHY
addresses for GMAC are 01h and 02h.
1.3
Physical Coding Sublayer (PCI) Interface
For the MVTX2603, the 1000BASE-X PCI Interface is designed internally and may be utilized in the absence of a
GMII. The PCS incorporates all the functions required by the GMII to include encoding (decoding) 8B GMII data to
(from) 8B/10B TBI format for PHY communication and generating Collision Detect (COL) signals for half-duplex
mode. It also manages the Auto negotiation process by informing the management entity that the PHY is ready for
communications. The on-chip TBI may be disabled if TBI exists within the Gigabit PHY. The TBI interface provides
a uniform interface for all 1000 Mbps PHY implementations.
The PCS comprises the PCS Transmit, Synchronization, PCS Receive and Auto negotiation processes for
1000BASE-X.
The PCS Transmit process sends the TBI signals TXD [9:0] to the physical medium and generates the GMII
Collision Detect (COL) signal based on whether a reception is occurring simultaneously with transmission.
Additionally, the Transmit process generates an internal “transmitting” flag and monitors Auto negotiation to
determine whether to transmit data or to reconfigure the link.
The PCS Synchronization process determines whether or not the receive channel is operational.
The PCS Receive process generates RXD [7:0] on the GMII from the TBI data [9:0], and the internal “receiving” flag
for use by the Transmit processes.
The PCS Auto negotiation process allows the MVTX2603 to exchange configuration information between two
devices that share a link segment and to automatically configure the link for the appropriate speed of operation for
both devices.
1.4
10/100 MAC Module (RMAC)
The 10/100 Media Access Control module provides the necessary buffers and control interface between the Frame
Engine (FE) and the external physical device (PHY). The MVTX2603 has two interfaces, RMII or Serial (only for
10 M). The 10/100 MAC of the MVTX2603 device meets the IEEE 802.3 specification. It is able to operate in either
Half or Full Duplex mode with a back pressure/flow control mechanism. In addition, it will automatically retransmit
upon collision for up to 16 total transmissions. The PHY address for 24 10/100 MAC are from 08h to 1fh.
10
Zarlink Semiconductor Inc.
MVTX2603
1.5
Data Sheet
Configuration Interface Module
The MVTX2603 supports a serial and an I2C interface, which provides an easy way to configure the system. Once
configured, the resulting configuration can be stored in an I2C EEPROM.
1.6
Frame Engine
The main function of the frame engine is to forward a frame to its proper destination port or ports. When a frame
arrives, the frame engine parses the frame header (64 bytes) and formulates a switching request, which is sent to
the search engine to resolve the destination port. The arriving frame is moved to the FDB. After receiving a switch
response from the search engine, the frame engine performs transmission scheduling based on the frame’s priority.
The frame engine forwards the frame to the MAC module when the frame is ready to be sent.
1.7
Search Engine
The Search Engine resolves the frame’s destination port or ports according to the destination MAC address (L2). It
also performs MAC learning, priority assignment and trunking functions.
1.8
LED Interface
The LED interface provides a serial interface for carrying 24+2 port status signals. It can also provide direct status
pins (6) for the two Gigabit ports.
1.9
Internal Memory
Several internal tables are required and are described as follows:
•
•
Frame Control Block (FCB) - Each FCB entry contains the control information of the associated frame
stored in the FDB, e.g., frame size, read/write pointer, transmission priority, etc.
MCT Link Table - The MCT Link Table stores the linked list of MCT entries that have collisions in the
external MAC Table. The external MAC table is located in the FDB Memory.
Note: the external MAC table is located in the external SBRAM Memory.
2.0
System Configuration
2.1
Configuration Mode
The MVTX2603 can be configured by EEPROM (24C02 or compatible) via an I2C interface at boot time, or via a
synchronous serial interface during operation.
2.2
I2C Interface
The I2C interface uses two bus lines, a serial data line (SDA) and a serial clock line (SCL). The SCL line carries the
control signals that facilitate the transfer of information from EEPROM to the switch. Data transfer is 8-bit serial and
bidirectional, at 50 Kbps. Data transfer is performed between master and slave IC using a request /
acknowledgment style of protocol. The master IC generates the timing signals and terminates data transfer. Figure
2 depicts the data transfer format.
START
SLAVE ADDRESS
R/W
ACK
DATA 1 (8 bits)
ACK
DATA 2
ACK
Figure 2 - Data Transfer Format for I2C Interface
11
Zarlink Semiconductor Inc.
DATA M
ACK
STOP
MVTX2603
2.2.1
Data Sheet
Start Condition
Generated by the master (in our case, the MVTX2603). The bus is considered to be busy after the Start condition is
generated. The Start condition occurs if while the SCL line is High, there is a High-to-Low transition of the SDA line.
Other than in the Start condition (and Stop condition), the data on the SDA line must be stable during the High
period of SCL. The High or Low state of SDA can only change when SCL is Low. In addition, when the I2C bus is
free, both lines are High.
2.2.2
Address
The first byte after the Start condition determines which slave the master will select. The slave in our case is the
EEPROM. The first seven bits of the first data byte make up the slave address.
2.2.3
Data Direction
The eighth bit in the first byte after the Start condition determines the direction (R/W) of the message. A master
transmitter sets this bit to W; a master receiver sets this bit to R.
2.2.4
Acknowledgment
Like all clock pulses, the acknowledgment-related clock pulse is generated by the master. However, the transmitter
releases the SDA line (High) during the acknowledgment clock pulse. Furthermore, the receiver must pull down the
SDA line during the acknowledge pulse so that it remains stable Low during the High period of this clock pulse. An
acknowledgment pulse follows every byte transfer.
If a slave receiver does not acknowledge after any byte, then the master generates a Stop condition and aborts the
transfer.
If a master receiver does not acknowledge after any byte, then the slave transmitter must release the SDA line to let
the master generate the Stop condition.
2.2.5
Data
After the first byte containing the address, all bytes that follow are data bytes. Each byte must be followed by an
acknowledge bit. Data is transferred MSB first.
2.2.6
Stop Condition
Generated by the master. The bus is considered to be free after the Stop condition is generated. The Stop condition
occurs if while the SCL line is High, there is a Low-to-High transition of the SDA line.
The I2C interface serves the function of configuring the MVTX2603 at boot time. The master is the MVTX2603 and
the slave is the EEPROM memory.
2.3
Synchronous Serial Interface
The synchronous serial interface serves the function of configuring the MVTX2603 not at boot time but via a PC.
The PC serves as master and the MVTX2603 serves as slave. The protocol for the synchronous serial interface is
nearly identical to the I2C protocol. The main difference is that there is no acknowledgment bit after each byte of
data transferred.
The unmanaged MVTX2603 uses a synchronous serial interface to program the internal registers. To reduce the
number of signals required, the register address, command and data are shifted in serially through the D0 pin.
STROBE- pin is used as the shift clock. AUTOFD- pin is used as data return path.
12
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
Each command consists of four parts.
START pulse
Register Address
Read or Write command
Data to be written or read back
Any command can be aborted in the middle by sending a ABORT pulse to the MVTX2603.
A START command is detected when D0 is sampled high when STROBE- rise and D0 is sampled low when
STROBE- fall.
An ABORT command is detected when D0 is sampled low when STROBE- rise and D0 is sampled high when
STROBE- fall.
2.3.1
Write Command
STROBE2 extra
clock cycles
2 Extra clocks
after last
after last transfer
transfer
D0
A2
A0 A1 A2
START
...
...
A11 W
A9 A10
A10 A11
A9
ADDRESS
D0 D1
D1 D2
D2 D3
D3 D4
D4 D5
D5 D6
D6 D7
D7
D0
COMMAND
DATA
Figure 3 - Write Command
2.3.2
Read Command
STROBE-
A10 A11
A11 RR
A0 A1
A1 A2
A0
A9 A10
A2 ...... A9
D0
START
AUTOFD-
ADDRESS
COMMAND
DATA
D0 D1 D2 D3 D4 D5
D5 D6 D7
Figure 4 - Read Command
All registers in MVTX2603 can be modified through this synchronous serial interface.
2.4
Stacking
The two Gigabits ports can be used as link between boxes. Each Gigabit port can be accelerated to 2 Gpbs if
desired (in conjunction with ZBT memory domains at 125 MHz). If both Gigabit ports are used for this purpose, this
provides a total of 4 Gbps of bandwidth between devices.
13
Zarlink Semiconductor Inc.
MVTX2603
3.0
MVTX2603 Data Forwarding Protocol
3.1
Unicast Data Frame Forwarding
Data Sheet
When a frame arrives, it is assigned a handle in memory by the Frame Control Buffer Manager (FCB Manager). An
FCB handle will always be available, because of advance buffer reservations.
The memory (SRAM) interface consists of two 64-bit buses, connected to two SRAM banks, A and B. The Receive
DMA (RxDMA) is responsible for multiplexing the data and the address. On a port’s “turn,” the RxDMA will move 8
bytes (or up to the end-of-frame) from the port’s associated RxFIFO into memory (Frame Data Buffer, or FDB).
Once an entire frame has been moved to the FDB and a good end-of-frame (EOF) has been received, the Rx
interface makes a switch request. The RxDMA arbitrates among multiple switch requests.
The switch request consists of the first 64 bytes of a frame, containing among other things, the source and
destination MAC addresses of the frame. The search engine places a switch response in the switch response
queue of the frame engine when done. Among other information, the search engine will have resolved the
destination port of the frame and will have determined that the frame is unicast.
After processing the switch response, the Transmission Queue Manager (TxQ manager) of the frame engine is
responsible for notifying the destination port that it has a frame to forward to it. But first, the TxQ manager has to
decide whether or not to drop the frame, based on global FDB reservations and usage, as well as TxQ occupancy
at the destination. If the frame is not dropped, then the TxQ manager links the frame’s FCB to the correct per-portper-class TxQ. Unicast TxQ’s are linked lists of transmission jobs, represented by their associated frames’ FCB’s.
There is one linked list for each transmission class for each port. There are 4 transmission classes for each of the
24 10/100 ports and 8 classes for each of the two Gigabit ports – a total of 112 unicast queues.
The TxQ manager is responsible for scheduling transmission among the queues representing different classes for a
port. When the port control module determines that there is room in the MAC Transmission FIFO (TxFIFO) for
another frame, it requests the handle of a new frame from the TxQ manager. The TxQ manager chooses among
the head-of-line (HOL) frames from the per-class queues for that port using a Zarlink Semiconductor scheduling
algorithm.
The Transmission DMA (TxDMA) is responsible for multiplexing the data and the address. On a port’s turn, the
TxDMA will move 8 bytes (or up to the EOF) from memory into the port’s associated TxFIFO. After reading the EOF,
the port control requests a FCB release for that frame. The TxDMA arbitrates among multiple buffer release
requests.
The frame is transmitted from the TxFIFO to the line.
3.2
Multicast Data Frame Forwarding
After receiving the switch response, the TxQ manager has to make the dropping decision. A global decision to drop
can be made, based on global FDB utilization and reservations. If so, then the FCB is released and the frame is
dropped. In addition, a selective decision to drop can be made, based on the TxQ occupancy at some subset of the
multicast packet’s destinations. If so, then the frame is dropped at some destinations but not others and the FCB is
not released.
If the frame is not dropped at a particular destination port, then the TxQ manager formats an entry in the multicast
queue for that port and class. Multicast queues are physical queues (unlike the linked lists for unicast frames).
There are 2 multicast queues for each of the 24 10/100 ports. The queue with higher priority has room for 32 entries
and the queue with lower priority has room for 64 entries. There are 4 multicast queues for each of the two Gigabit
ports. The sizes of the queues are: 32 entries (higher priority queue, 32 entries, 32 entries and 64 entries (lower
priority queue). There is one multicast queue for every two priority classes. For the 10/100 ports to map the 8
transmit priorities into 2 multicast queues, the 2 LSB are discarded. For the gigabit ports to map the 8 transmit
priorities into 4 multicast queues, the LSB are discarded.
14
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
During scheduling, the TxQ manager treats the unicast queue and the multicast queue of the same class as one
logical queue. The older head of line of the two queues is forwarded first.
The port control requests a FCB release only after the EOF for the multicast frame has been read by all ports to
which the frame is destined.
4.0
Memory Interface
4.1
Overview
The MVTX2603 provides two 64-bit wide SRAM banks, SRAM Bank A and SRAM Bank B, with a 64-bit bus
connected to each. Each DMA can read and write from both bank A and bank B. The following figure provides an
overview of the MVTX2603 SRAM banks.
SRAM Bank A
TXDMA
0-7
TXDMA
8-15
SRAM Bank B
TXDMA
16-23
RXDMA
0-7
RXDMA
8-15
RXDMA
16-23
Figure 5 - MVTX2603 SRAM Interface Block Diagram (DMAs for 10/1000 Ports Only)
4.2
ZBT Support
The MVTX2603 supports Zero Bus Turnaround (ZBT). ZBT is a synchronous SRAM architecture that is optimized
for networking and telecommunications applications. It can significantly increase the switch’s internal bandwidth
when compared to standard Pipeline SyncBurst SRAM.
The ZBT architecture is optimized for switching and other applications with highly random READs and WRITEs.
ZBT SRAMs eliminate all idle cycles when turning the data bus around from a WRITE operation to a READ
operation (or vice versa). This feature results in dramatic performance improvements in systems that have such
traffic patterns (that is, frequent and random read and write access to the SRAM).
Please refer to the ZBT Application Note for further details.
4.3
Detailed Memory Information
Because the bus for each bank is 64-bits wide, frames are broken into 8-byte granules, written to and read from
memory. The first 8-byte granule gets written to Bank A, the second 8-byte granule gets written to Bank B, and so
on in alternating fashion. When reading frames from memory, the same procedure is followed, first from A, then
from B and so on.
15
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
The reading and writing from alternating memory banks can be performed with minimal waste of memory
bandwidth. What’s the worst case? For any speed port, in the worst case, a 1-byte-long EOF granule gets
written to Bank A. This means that a 7-byte segment of Bank A bandwidth is idle, and furthermore, the next 8-byte
segment of Bank B bandwidth is idle, because the first 8 bytes of the next frame will be written to Bank A, not B.
This scenario results in a maximum 15 bytes of waste per frame, which is always acceptable because the
interframe gap is 20 bytes.
Search engine data is written to both banks in parallel. In this way, a search engine read operation can be
performed by either bank at any time without a problem.
4.4
Memory Requirements
To speed up searching and decrease memory latency, the external MCT database is duplicated in both memory
banks. To support 64 K MCT, 4 MB memory is required. Up to 2 K frame buffers are supported and they will use
3 MB of memory. The maximum system memory requirement is 4 MB. If less memory is desired, the configuration
can scale down proportionally.
Bank A
Bank B
Frame Buffer
Max MAC Address
1M
1M
1K
32 K
2M
2M
2K
64 k
Table 1 - Memory Configuration
1 M Bank A
1 M Bank B
2 M Bank A
2 M Bank B
0.75 M
0.75 M
1.5 M
1.5 M
0.25 M
0.25 M
0.5 M
0.5 M
Frame Data Buffer (FDR) Area
MAC Address Control Table (MCT) Area
Figure 6 - Memory Map
5.0
Search Engine
5.1
Search Engine Overview
The MVTX2603 search engine is optimized for high throughput searching, with enhanced features to support:
•
•
•
•
•
•
Up to 64 K MAC addresses
3 groups of port trunking (1 for the two Gigabit ports, and 2 others)
Traffic classification into 4 (or 8 for Gigabit) transmission priorities, and 2 drop precedence levels
Flooding, Broadcast, Multicast Storm Control
MAC address learning and aging
Port based VLAN
16
Zarlink Semiconductor Inc.
MVTX2603
5.2
Data Sheet
Basic Flow
Shortly after a frame enters the MVTX2603 and is written to the Frame Data Buffer (FDB), the frame engine
generates a Switch Request, which is sent to the search engine. The switch request consists of the first 64 bytes of
the frame, which contain all the necessary information for the search engine to perform its task. When the search
engine is done, it writes to the Switch Response Queue, and the frame engine uses the information provided in that
queue for scheduling and forwarding.
In performing its task, the search engine extracts and compresses the useful information from the 64-byte switch
request. Among the information extracted are the source and destination MAC addresses, the transmission and
discard priorities, whether the frame is unicast or multicast. Requests are sent to the external SRAM to locate the
associated entries in the external hash table.
When all the information has been collected from external SRAM, the search engine has to compare the MAC
address on the current entry with the MAC address for which it is searching. If it is not a match, the process is
repeated on the internal MCT Table. All MCT entries other than the first of each linked list are maintained internal to
the chip. If the desired MAC address is still not found, then the result is either learning (source MAC address
unknown) or flooding (destination MAC address unknown).
In addition, port based VLAN information is used to select the correct set of destination ports for the frame (for
multicast) or to verify that the frame’s destination port is associated with the VLAN (for unicast).
If the destination MAC address belongs to a port trunk, then the trunk number is retrieved instead of the port
number. But on which port of the trunk will the frame be transmitted? This is easily computed using a hash of the
source and destination MAC addresses.
As stated earlier, when all the information is compiled the switch response is generated.
5.3
5.3.1
Search, Learning, and Aging
MAC Search
The search block performs source MAC address and destination MAC address searching. As we indicated earlier,
if a match is not found, then the next entry in the linked list must be examined, and so on until a match is found or
the end of the list is reached.
The port based VLAN bitmap is used to determine whether the frame should be forwarded to the outgoing port.
When the egress port is not included in the ingress port VLAN bitmap, the packet is discarded.
The MAC search block is also responsible for updating the source MAC address timestamp and the VLAN port
association timestamp, used for aging.
5.3.2
Learning
The learning module learns new MAC addresses and performs port change operations on the MCT database. The
goal of learning is to update this database as the networking environment changes over time. Learning and port
change will be performed based on memory slot availability only.
5.3.3
Aging
Aging time is controlled by register 400h and 401h.
The aging module scans and ages MCT entries based on a programmable “age out” time interval. As we indicated
earlier, the search module updates the source MAC address timestamps for each frame it processes. When an
entry is ready to be aged, the entry is removed from the table.
17
Zarlink Semiconductor Inc.
MVTX2603
5.4
Data Sheet
Quality of Service
Quality of Service (QoS) refers to the ability of a network to provide better service to selected network traffic over
various technologies. Primary goals of QoS include dedicated bandwidth, controlled jitter and latency (required by
some real-time and interactive traffic) and improved loss characteristics.
Traditional Ethernet networks have had no prioritization of traffic. Without a protocol to prioritize or differentiate
traffic, a service level known as “best effort” attempts to get all the packets to their intended destinations with
minimum delay; however, there are no guarantees. In a congested network or when a low-performance
switch/router is overloaded, “best effort” becomes unsuitable for delay-sensitive traffic and mission-critical data
transmission.
The advent of QoS for packet-based systems accommodates the integration of delay-sensitive video and
multimedia traffic onto any existing Ethernet network. It also alleviates the congestion issues that have previously
plagued such “best effort” networking systems. QoS provides Ethernet networks with the breakthrough technology
to prioritize traffic and ensure that a certain transmission will have a guaranteed minimum amount of bandwidth.
Extensive core QoS mechanisms are built into the MVTX2603 architecture to ensure policy enforcement and
buffering of the ingress port, as well as weighted fair-queue (WFQ) scheduling at the egress port.
In the MVTX2603, QoS-based policies sort traffic into a small number of classes and mark the packets accordingly.
The QoS identifier provides specific treatment to traffic in different classes, so that different quality of service is
provided to each class. Frame and packet scheduling and discarding policies are determined by the class to which
the frames and packets belong. For example, the overall service given to frames and packets in the premium class
will be better than that given to the standard class; the premium class is expected to experience lower loss rate or
delay.
The MVTX2603 supports the following QoS techniques:
•
•
•
•
5.5
In a port-based setup, any station connected to the same physical port of the switch will have the same
transmit priority.
In a tag-based setup, a 3-bit field in the VLAN tag provides the priority of the packet. This priority can be
mapped to different queues in the switch to provide QoS.
In a TOS/DS-based set up, TOS stands for “Type of Service” that may include “minimize delay,” “maximize
throughput,” or “maximize reliability.” Network nodes may select routing paths or forwarding behaviours that
are suitably engineered to satisfy the service request.
In a logical port-based set up, a logical port provides the application information of the packet. Certain
applications are more sensitive to delays than others; using logical ports to classify packets can help speed
up delay sensitive applications, such as VoIP.
Priority Classification Rule
Figure 7 on page 19 shows the MVTX2603 priority classification rule
18
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
Yes
Use Default Port Settings
Fix Port Priority ?
No
TOS Precedence over VLAN?
(FCR Register, Bit 7)
Use Default Port Settings
No
No
No
IP
Yes
No
VLAN Tag ?
Yes
IP Frame ?
Yes
Yes
No
Use Logical Port
Use TOS
Yes
Use VLAN Priority
Use Logical Port
Figure 7 - Priority Classification Rule
5.6
Port Based VLAN
An administrator can use the PVMAP Registers to configure the MVTX2603 for port-based VLAN. For example,
ports 1-3 might be assigned to the Marketing VLAN, ports 4-6 to the Engineering VLAN, and ports 7-9 to the
Administrative VLAN. The MVTX2603 determines the VLAN membership of each packet by noting the port on
which it arrives. From there, the MVTX2603 determines which outgoing port(s) is/are eligible to transmit each
packet, or whether the packet should be discarded.
Destination Port Numbers Bit Map
Port Registers
26
Register for Port #0
PVMAP00_0[7:0] to PVMAP00_3[2:0]
…
2
1
0
0
1
1
0
Register for Port #1
PVMAP01_0[7:0] to PVMAP01_3[2:0]
0
1
0
1
Register for Port #2
PVMAP02_0[7:0] to PVMAP02_3[2:0]
0
0
0
0
0
0
0
0
…
Register for Port #26
PVMAP26_0[7:0] to PVMAP26_3[2:0]
Table 2 - PVMAP Register
For example, in the above table, a 1 denotes that an outgoing port is eligible to receive a packet from an incoming
port. A 0 (zero) denotes that an outgoing port is not eligible to receive a packet from an incoming port.
19
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
In this example:
•
•
•
Data packets received at port #0 are eligible to be sent to outgoing ports 1 and 2
Data packets received at port #1 are eligible to be sent to outgoing ports 0, and 2
Data packets received at port #2 are not eligible to be sent to ports 0 and 1
5.7
Memory Configurations
The MVTX2603 supports the following memory configurations. SBRAM modes support 1 M and 2 M configurations,
while ZBT mode supports 4 M configurations, 2 M per domain (bank). For detail connection information, please
reference the memory application note.
1 M per bank
(Bootstrap pin
TSTOUT7 = open)
Configuration
Single Layer
(Bootstrap pin
TSTOUT13 = open)
Two 128 K x 32
SRAM/bank or
Double Layer
(Bootstrap pin
TSTOUT13 = pull down)
NA
2 M per bank
(Bootstrap pin
TSTOUT7 = pull down)
Connections
Two 256 K x 32
SRAM/bank
Connect 0E# and WE#
Four 128 K x 32
SRAM/bank or
Connect 0E0# and
WE0# Connect 0E1#
and WE1#
One 128 K x 64 SRAM/bank
Two 128 K x 64 SRAM/bank
Table 3 - Supported Memory Configurations (Pipeline SBRAM Mode)
20
Zarlink Semiconductor Inc.
MVTX2603
Configuration
Data Sheet
2 M per bank
Connections
Single Layer
(Bootstrap pin
TSTOUT13 = open)
Two 256 K x 32 ZBT SRAM/bank
or One 256 K x 64 ZBT SRAM/bank
Connect ADS# to Layer 0 chipselect pin
Double Layer
(Bootstrap pin
TSTOUT13 = pull down)
Four 128 K x 32 ZBT SRAM/bank
or Two 128 K x 64 ZBT SRAM/bank
Connect ADS# to Layer 0 chipselect pin
and 0E# to Layer 1 chipselect pin
Table 4 - Supported Memory Configurations (ZBT Mode)
Frame data Buffer
Only Bank A
1M
(SRAM)
2M
(SRAM)
MVTX2601
X
X
MVTX2602
X
X
Bank A and Bank B
MVTX2603
1 M/bank
(SRAM)
2 M/bank
(SRAM)
X
X
MVTX2603
(Gigabit ports in 2 giga mode)
MVTX2604
X
Bank A and Bank B
1 M/bank
(ZBT SRAM)
2 M/bank
(ZBT SRAM)
X (125 Mhz)
X (125 Mhz)
X (125 Mhz)
X (125 Mhz)
X
MVTX2604
(Gigabit ports in 2 giga mode)
Table 5 - Options for Memory Configuration
Bank A (1M One Layer)
Bank B (1M One Layer)
Data LA_D[63:32]
Data LB_D[63:32]
Data LB_D[31:0]
Data LA_D[31:0]
SRAM
Memory
128K
32 bits
SRAM
Memory
128K
32 bits
Memory
128K
32 bits
Address LB_A[19:3]
Address LA_A[19:3]
B
t t
TSTOUT7
O
TSTOUT13
O
TSTOUT4
O
Figure 8 - Memory Configuration For: 2 Banks, 1 Layer, 2 MB Total
21
Zarlink Semiconductor Inc.
Memory
128K
32 bits
MVTX2603
Data Sheet
BANK A (2M Two Layers)
BANK B (2M Two Layers)
Data LA_D[63:32]
Data LA_D[31:0]
Data LB_D[63:32]
SRAM
Memory
128 K
32 bits
SRAM
Memory
128 K
32 bits
SRAM
Memory
128 K
32 bits
SRAM
Memory
128 K
32 bits
Data LB_D[31:0]
Address LA_A[19:3]
SRAM
Memory
128 K
32 bits
SRAM
Memory
128 K
32 bits
SRAM
Memory
128 K
32 bits
SRAM
Memory
128 K
32 bits
Address LB_A[19:3]
Bootstraps: TSTOUT7 = Pull Down, TSTOUT13 = Pull Down, TSTOUT4 = Open
M
C fi
ti
F
2b k 2L
4MB t t l
Figure 9 - Memory Configuration For: 2 Banks, 2 Layer, 4 MB Total
BANK A (2M One Layer)
BANK B (2M One Layer)
Data LA_D[63:32]
Data LA_D[31:0]
SRAM
Memory
256 K
32 bits
Data LB_D[63:32]
Data LB_D[31:0]
Memory
256 K
32 bits
Address LA_A[20:3]
SRAM
Memory
256 K
32 bits
Address LB_A[20:3]
Bootstraps: TSTOUT7 = Pull Down, TSTOUT13 = Open, TSTOUT4 = Open
Figure 10 - Memory Configuration For: 2 Banks, 1 Layer, 4 MB
22
Zarlink Semiconductor Inc.
Memory
256 K
32 bits
MVTX2603
Data Sheet
BANK A (2M Two Layers)
BANK B (2M Two Layers)
Data LA_D[63:32]
Data LA_D[31:0]
Data LB_D[63:32]
ZBT
Memory
128 K
32 bits
ZBT
Memory
128 K
32 bits
ZBT
Memory
128 K
32 bits
ZBT
Memory
128 K
32 bits
Data LB_D[31:0]
Address LA_A[19:3]
ZBT
Memory
128 K
32 bits
ZBT
Memory
128 K
32 bits
ZBT
Memory
128 K
32 bits
ZBT
Memory
128 K
32 bits
Address LB_A[19:3]
Figure 11 - Memory Configuration For: 2 Banks, 2 Layers, 4 MB Total
BANK A (2M One Layer)
BANK B (2M One Layer)
Data LA_D[63:32]
Data LA_D[31:0]
ZBT
Memory
256 K
32 bits
Data LB_D[63:32]
ZBT
Memory
256 K
32 bits
Data LB_D[31:0]
Address LA_A[20:3]
ZBT
Memory
256 K
32 bits
ZBT
Memory
256 K
32 bits
Address LB_A[20:3]
Bootstraps: TSTOUT7 = Pull Down, TSTOUT13 = Open, TSTOUT4 = Pull Down
Figure 12 - Memory Configuration For: 2 Banks, 1 Layer, 4 MB
23
Zarlink Semiconductor Inc.
MVTX2603
6.0
Frame Engine
6.1
Data Forwarding Summary
•
•
•
•
•
•
Data Sheet
When a frame enters the device at the RxMAC, the RxDMA will move the data from the MAC RxFIFO to the
FDB. Data is moved in 8-byte granules in conjunction with the scheme for the SRAM interface.
A switch request is sent to the Search Engine. The Search Engine processes the switch request.
A switch response is sent back to the Frame Engine and indicates whether the frame is unicast or multicast
and its destination port or ports.
A Transmission Scheduling Request is sent in the form of a signal notifying the TxQ manager. Upon
receiving a Transmission Scheduling Request, the device will format an entry in the appropriate
Transmission Scheduling Queue (TxSch Q) or Queues. There are 4 TxSch Q for each 10/100 port (and 8
per Gigabit port), one for each priority. Creation of a queue entry either involves linking a new job to the
appropriate linked list if unicast or adding an entry to a physical queue if multicast.
When the port is ready to accept the next frame, the TxQ manager will get the head-of-line (HOL) entry of
one of the TxSch Qs, according to the transmission scheduling algorithm (to ensure per-class quality of
service). The unicast linked list and the multicast queue for the same port-class pair are treated as one
logical queue. The older HOL between the two queues goes first. For 10/100 ports multicast queue 0 is
associated with unicast queue 0 and multicast queue 1 is associated with unicast queue 2. For Gigabit ports
multicast queue 0 is associated with unicast queue 0, multicast queue 1 with unicast queue 2, multicast
queue 2 with unicast queue 4 and multicast queue 3 with unicast queue 6.
The TxDMA will pull frame data from the memory and forward it granule-by-granule to the MAC TxFIFO of
the destination port.
6.2
Frame Engine Details
This section briefly describes the functions of each of the modules of the MVTX2603 frame engine.
6.2.1
FCB Manager
The FCB manager allocates FCB handles to incoming frames, and releases FCB handles upon frame departure.
The FCB manager is also responsible for enforcing buffer reservations and limits. The default values can be
determined by referring to Chapter 8. In addition, the FCB manager is responsible for buffer aging and for linking
unicast forwarding jobs to their correct TxSch Q. The buffer aging can be enabled or disabled by the bootstrap pin
and the aging time is defined in register FCBAT.
6.2.2
Rx Interface
The Rx interface is mainly responsible for communicating with the RxMAC. It keeps track of the start and end of
frame and frame status (good or bad). Upon receiving an end of frame that is good, the Rx interface makes a switch
request.
6.2.3
RxDMA
The RxDMA arbitrates among switch requests from each Rx interface. It also buffers the first 64 bytes of each
frame for use by the search engine when the switch request has been made.
6.2.4
TxQ Manager
First, the TxQ manager checks the per-class queue status and global reserved resource situation, and using this
information, makes the frame dropping decision after receiving a switch response. If the decision is not to drop, the
TxQ manager requests that the FCB manager link the unicast frame’s FCB to the correct per-port-per-class TxQ. If
multicast, the TxQ manager writes to the multicast queue for that port and class. The TxQ manager can also trigger
24
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
source port flow control for the incoming frame’s source if that port is flow control enabled. Second, the TxQ
manager handles transmission scheduling; it schedules transmission among the queues representing different
classes for a port. Once a frame has been scheduled, the TxQ manager reads the FCB information and writes to
the correct port control module.
6.3
Port Control
The port control module calculates the SRAM read address for the frame currently being transmitted. It also writes
start of frame information and an end of frame flag to the MAC TxFIFO. When transmission is done, the port control
module requests that the buffer be released.
6.4
TxDMA
The TxDMA multiplexes data and address from port control, and arbitrates among buffer release requests from the
port control modules.
7.0
Quality of Service and Flow Control
7.1
Model
Quality of service is an all-encompassing term for which different people have different interpretations. In general,
the approach to quality of service described here assumes that we do not know the offered traffic pattern. We also
assume that the incoming traffic is not policed or shaped. Furthermore, we assume that the network manager
knows his applications, such as voice, file transfer, or web browsing, and their relative importance. The manager
can then subdivide the applications into classes and set up a service contract with each. The contract may consist
of bandwidth or latency assurances per class. Sometimes it may even reflect an estimate of the traffic mix offered to
the switch. As an added bonus, although we do not assume anything about the arrival pattern, if the incoming traffic
is policed or shaped, we may be able to provide additional assurances about our switch’s performance.
Table 6 on page 25 shows examples of QoS applications with three transmission priorities, but best effort (P0)
traffic may form a fourth class with no bandwidth or latency assurances. Gigabit ports actually have eight total
transmission priorities.
Goals
Total
Assured Bandwidth
(user defined)
Low Drop Probability
(low-drop)
High Drop Probability
(high-drop)
Highest transmission
priority, P3
50 Mbps
Apps: phone calls, circuit
emulation.
Latency: < 1 ms.
Drop: No drop if P3 not
oversubscribed.
Apps: training video.
Latency: < 1 ms.
Drop: No drop if P3 not
oversubscribed; first P3 to
drop otherwise.
Middle transmission
priority, P2
37.5 Mbps
Apps: interactive apps, Web
business.
Latency: < 4-5 ms.
Drop: No drop if P2 not
oversubscribed.
Apps: non-critical interactive
apps.
Latency: < 4-5 ms.
Drop: No drop if P2 not
oversubscribed; first P2 to
drop otherwise.
Table 6 - Two-dimensional World Traffic
25
Zarlink Semiconductor Inc.
MVTX2603
Low transmission
priority, P1
12.5 Mbps
Total
100 Mbps
Apps: emails, file backups.
Latency: < 16 ms desired, but
not critical.
Drop: No drop if P1 not
oversubscribed.
Data Sheet
Apps: casual web browsing.
Latency: < 16 ms desired, but
not critical.
Drop: No drop if P1 not
oversubscribed; first to drop
otherwise.
Table 6 - Two-dimensional World Traffic
A class is capable of offering traffic that exceeds the contracted bandwidth. A well-behaved class offers traffic at a
rate no greater than the agreed-upon rate. By contrast, a misbehaving class offers traffic that exceeds the agreedupon rate. A misbehaving class is formed from an aggregation of misbehaving microflows. To achieve high link
utilization, a misbehaving class is allowed to use any idle bandwidth. However, such leniency must not degrade the
quality of service (QoS) received by well-behaved classes.
As Table 6 illustrates, the six traffic types may each have their own distinct properties and applications. As shown,
classes may receive bandwidth assurances or latency bounds. In the table, P3, the highest transmission class,
requires that all frames be transmitted within 1 ms, and receives 50% of the 100 Mbps of bandwidth at that port.
Best-effort (P0) traffic forms a fourth class that only receives bandwidth when none of the other classes have any
traffic to offer. It is also possible to add a fourth class that has strict priority over the other three; if this class has
even one frame to transmit, then it goes first. In the MVTX2603, each 10/100 Mbps port will support four total
classes, and each 1000 Mbps port will support eight classes. We will discuss the various modes of scheduling
these classes in the next section.
In addition, each transmission class has two subclasses, high-drop and low-drop. Well-behaved users should rarely
lose packets. But poorly behaved users – users who send frames at too high a rate – will encounter frame loss, and
the first to be discarded will be high-drop. Of course, if this is insufficient to resolve the congestion, eventually some
low-drop frames are dropped, and then all frames in the worst case.
Table 6 shows that different types of applications may be placed in different boxes in the traffic table. For example,
casual web browsing fits into the category of high-loss, high-latency-tolerant traffic, whereas VoIP fits into the
category of low-loss, low-latency traffic.
7.2
Four QoS Configurations
There are four basic pieces to QoS scheduling in the MVTX2603: strict priority (SP), delay bound, weighted fair
queuing (WFQ), and best effort (BE). Using these four pieces, there are four different modes of operation, as shown
in Table 4, “Supported Memory Configurations (ZBT Mode),” and Table 6, “Two-dimensional World Traffic,” . For
10/100 Mbps ports, these modes are selected by the following registers:
QOSC24 [7:6]
CREDIT_C00
QOSC28 [7:6]
CREDIT_C10
QOSC32 [7:6]
CREDIT_C20
QOSC36 [7:6]
CREDIT_C30
26
Zarlink Semiconductor Inc.
MVTX2603
P3
Data Sheet
P2
Op1 (default)
Delay Bound
Op2
SP
Delay Bound
Op3
SP
WFQ
Op4
WFQ
P1
P0
BE
BE
Table 7 - Four QoS Configurations for a 10/100 Mbps Port
These modes are selected by QOSC40 [7:6] and QOSC48 [7:6] for the first and second gigabit ports, respectively.
P7
P6
P5
P4
Op1 (default)
Delay Bound
Op2
SP
Delay Bound
Op3
SP
WFQ
Op4
WFQ
P3
P2
P1
P0
BE
BE
Table 8 - Four QoS Configurations for a Gigabit Port
The default configuration for a 10/100 Mbps port is three delay-bounded queues and one best-effort queue. The
delay bounds per class are 0.8 ms for P3, 2 ms for P2, and 12.8 ms for P1. For a 1 Gbps port, we have a default of
six delay-bounded queues and two best-effort queues. The delay bounds for a 1 Gbps port are 0.16 ms for P7 and
P6, 0.32 ms for P5, 0.64 ms for P4, 1.28 ms for P3, and 2.56 ms for P2. Best effort traffic is only served when there
is no delay-bounded traffic to be served. For a 1 Gbps port, where there are two best-effort queues, P1 has strict
priority over P0.
We have a second configuration for a 10/100 Mbps port in which there is one strict priority queue, two delay
bounded queues, and one best effort queue. The delay bounds per class are 3.2 ms for P2 and 12.8 ms for P1. If
the user is to choose this configuration, it is important that P3 (SP) traffic be either policed or implicitly bounded
(e.g., if the incoming P3 traffic is very light and predictably patterned). Strict priority traffic, if not admissioncontrolled at a prior stage to the MVTX2603, can have an adverse effect on all other classes’ performance. For a 1
Gbps port, P7 and P6 are both SP classes and P7 has strict priority over P6. In this case, the delay bounds per
class are 0.32 ms for P5, 0.64 ms for P4, 1.28 ms for P3, and 2.56 ms for P2.
The third configuration for a 10/100 Mbps port contains one strict priority queue and three queues receiving a
bandwidth partition via WFQ. As in the second configuration, strict priority traffic needs to be carefully controlled. In
the fourth configuration, all queues are served using a WFQ service discipline.
7.3
Delay Bound
In the absence of a sophisticated QoS server and signaling protocol, the MVTX2603 may not know the mix of
incoming traffic ahead of time. To cope with this uncertainty, our delay assurance algorithm dynamically adjusts its
scheduling and dropping criteria, guided by the queue occupancies and the due dates of their head-of-line (HOL)
frames. As a result, we assure latency bounds for all admitted frames with high confidence, even in the presence of
system-wide congestion. Our algorithm identifies misbehaving classes and intelligently discards frames at no
detriment to well-behaved classes. Our algorithm also differentiates between high-drop and low-drop traffic with a
weighted random early drop (WRED) approach. Random early dropping prevents congestion by randomly dropping
a percentage of high-drop frames even before the chip’s buffers are completely full, while still largely sparing lowdrop frames. This allows high-drop frames to be discarded early, as a sacrifice for future low-drop frames. Finally,
the delay bound algorithm also achieves bandwidth partitioning among classes.
27
Zarlink Semiconductor Inc.
MVTX2603
7.4
Data Sheet
Strict Priority and Best Effort
When strict priority is part of the scheduling algorithm, if a queue has even one frame to transmit, it goes first. Two
of our four QoS configurations include strict priority queues. The goal is for strict priority classes to be used for IETF
expedited forwarding (EF), where performance guarantees are required. As we have indicated, it is important that
strict priority traffic be either policed or implicitly bounded, so as to keep from harming other traffic classes.
When best effort is part of the scheduling algorithm, a queue only receives bandwidth when none of the other
classes have any traffic to offer. Two of our four QoS configurations include best effort queues. The goal is for best
effort classes to be used for non-essential traffic, because we provide no assurances about best effort performance.
However, in a typical network setting, much best effort traffic will indeed be transmitted and with an adequate
degree of expediency.
Because we do not provide any delay assurances for best effort traffic, we do not enforce latency by dropping best
effort traffic. Furthermore, because we assume that strict priority traffic is carefully controlled before entering the
MVTX2603, we do not enforce a fair bandwidth partition by dropping strict priority traffic. To summarize, dropping to
enforce bandwidth or delay does not apply to strict priority or best effort queues. We only drop frames from best
effort and strict priority queues when global buffer resources become scarce.
7.5
Weighted Fair Queuing
In some environments – for example, in an environment in which delay assurances are not required, but precise
bandwidth partitioning on small time scales is essential, WFQ may be preferable to a delay-bounded scheduling
discipline. The MVTX2603 provides the user with a WFQ option with the understanding that delay assurances can
not be provided if the incoming traffic pattern is uncontrolled. The user sets four WFQ “weights” (eight for Gigabit
ports) such that all weights are whole numbers and sum to 64. This provides per-class bandwidth partitioning with
error within 2%.
In WFQ mode, though we do not assure frame latency, the MVTX2603 still retains a set of dropping rules that helps
to prevent congestion and trigger higher level protocol end-to-end flow control.
As before, when strict priority is combined with WFQ, we do not have special dropping rules for the strict priority
queues, because the input traffic pattern is assumed to be carefully controlled at a prior stage. However, we do
indeed drop frames from SP queues for global buffer management purposes. In addition, queue P0 for a 10/100
port (and queues P0 and P1 for a Gigabit port) are treated as best effort from a dropping perspective, though they
still are assured a percentage of bandwidth from a WFQ scheduling perspective. What this means is that these
particular queues are only affected by dropping when the global buffer count becomes low.
7.6
Shaper
Although traffic shaping is not a primary function of the MVTX2603, the chip does implement a shaper for expedited
forwarding (EF). Our goal in shaping is to control the peak and average rate of traffic exiting the MVTX2603.
Shaping is limited to the two Gigabit ports only, and only to class P6 (the second highest priority). This means that
class P6 will be the class used for EF traffic. If shaping is enabled for P6, then P6 traffic must be scheduled using
strict priority. With reference to Table 8 only the middle two QoS configurations may be used.
Peak rate is set using a programmable whole number, no greater than 64. For example, if the setting is 32, then the
peak rate for shaped traffic is 32/64 * 1000 Mbps = 500 Mbps. Average rate is also a programmable whole number,
no greater than 64, and no greater than the peak rate. For example, if the setting is 16, then the average rate for
shaped traffic is 16/64 * 1000 Mbps = 250 Mbps. As a consequence of the above settings in our example, shaped
traffic will exit the MVTX2603 at a rate always less than 500 Mbps and averaging no greater than 250 Mbps. See
Programming QoS Registers Application Note for more information.
Also, when shaping is enabled, it is possible for a P6 queue to explode in length if fed by a greedy source. The
reason is that a shaper is by definition not work-conserving; that is, it may hold back from sending a packet even if
the line is idle. Though we do have global resource management, we do nothing to prevent this situation locally. We
assume SP traffic is policed at a prior stage to the MVTX2603.
28
Zarlink Semiconductor Inc.
MVTX2603
7.7
Data Sheet
WRED Drop Threshold Management Support
To avoid congestion, the Weighted Random Early Detection (WRED) logic drops packets according to specified
parameters. The following table summarizes the behavior of the WRED logic.
Table 9 - WRED Drop Thresholds
Px is the total byte count, in the priority queue x. The WRED logic has three drop levels, depending on the value of
N, which is based on the number of bytes in the priority queues. If delay bound scheduling is used, N equals
P3*16+P2*4+P1. If using WFQ scheduling, N equals P3+P2+P1. Each drop level from one to three has defined
high-drop and low-drop percentages, which indicate the minimum and maximum percentages of the data that can
be discarded. The X, Y Z percent can be programmed by the register RDRC0, RDRC1. In Level 3, all packets are
dropped if the bytes in each priority queue exceed the threshold. Parameters A, B, C are the byte count thresholds
for each priority queue. They can be programmed by the QOS control register (refer to the register group 5).
7.8
Buffer Management
Because the number of FDB slots is a scarce resource and because we want to ensure that one misbehaving
source port or class cannot harm the performance of a well-behaved source port or class, we introduce the concept
of buffer management into the MVTX2603. Our buffer management scheme is designed to divide the total buffer
space into numerous reserved regions and one shared pool as shown in Figure 13 on page 30.
As shown in the figure, the FDB pool is divided into several parts. A reserved region for temporary frames stores
frames prior to receiving a switch response. Such a temporary region is necessary, because when the frame first
enters the MVTX2603, its destination port and class are as yet unknown and so the decision to drop or not needs to
be temporarily postponed. This ensures that every frame can be received first before subjecting them to the frame
drop discipline after classifying.
Six reserved sections, one for each of the first six priority classes, ensure a programmable number of FDB slots per
class. The lowest two classes do not receive any buffer reservation. Furthermore, even for 10/100 Mbps ports, a
frame is stored in the region of the FDB corresponding to its class. As we have indicated, the eight classes use only
four transmission scheduling queues for 10/100 Mbps ports, but as far as buffer usage is concerned, there are still
eight distinguishable classes.
Another segment of the FDB reserves space for each of the 26 ports ethernet port. Two parameters can be set, one
for the source port reservation for 10/100 Mbps ports, and one for the source port reservation for 1 Gbps ports.
These 26 reserved regions make sure that no well-behaved source port can be blocked by another misbehaving
source port.
In addition, there is a shared pool, which can store any type of frame. The frame engine allocates the frames first in
the six priority sections. When the priority section is full or the packet has priority 1 or 0, the frame is allocated in the
shared poll. Once the shared poll is full the frames are allocated in the section reserved for the source port.
29
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
The following registers define the size of each section of the frame data buffer:
PR100- Port Reservation for 10/100 Ports
PRG- Port Reservation for Giga Ports
SFCB- Share FCB Size
C2RS- Class 2 Reserve Size
C3RS- Class 3 Reserve Size
C4RS- Class 4 Reserve Size
C5RS- Class 5 Reserve Size
C6RS- Class 6 Reserve Size
C7RS- Class 7 Reserve Size
temporary
reservation
shared pool
S
per-class
reservation
per-source
reservations
(24 10/100 M, CPU)
per-source
reservations
(2 G)
Figure 13 - Buffer Partition Scheme Used to Implement MVTX2603 Buffer Management
7.8.1
Dropping When Buffers Are Scarce
Summarizing the two examples of local dropping discussed earlier in this chapter:
•
•
If a queue is a delay-bounded queue, we have a multi-level WRED drop scheme, designed to control delay
and partition bandwidth in case of congestion.
If a queue is a WFQ-scheduled queue, we have a multi-level WRED drop scheme, designed to prevent
congestion.
In addition to these reasons for dropping, we also drop frames when global buffer space becomes scarce. The
function of buffer management is to make sure that such dropping causes as little blocking as possible.
30
Zarlink Semiconductor Inc.
MVTX2603
7.9
Data Sheet
MVTX2603 Flow Control Basics
Because frame loss is unacceptable for some applications, the MVTX2603 provides a flow control option. When
flow control is enabled, scarcity of buffer space in the switch may trigger a flow control signal; this signal tells a
source port that is sending a packet to this switch to temporarily hold off.
While flow control offers the clear benefit of no packet loss, it also introduces a problem for quality of service. When
a source port receives an Ethernet flow control signal, all microflows originating at that port, well-behaved or not,
are halted. A single packet destined for a congested output can block other packets destined for uncongested
outputs. The resulting head-of-line blocking phenomenon means that quality of service cannot be assured with high
confidence when flow control is enabled.
In the MVTX2603, each source port can independently have flow control enabled or disabled. For flow control
enabled ports, by default all frames are treated as lowest priority during transmission scheduling. This is done so
that those frames are not exposed to the WRED Dropping scheme. Frames from flow control enabled ports feed to
only one queue at the destination, the queue of lowest priority. What this means is that if flow control is enabled for
a given source port, then we can guarantee that no packets originating from that port will be lost, but at the possible
expense of minimum bandwidth or maximum delay assurances. In addition, these “downgraded” frames may only
use the shared pool or the per-source reserved pool in the FDB; frames from flow control enabled sources may not
use reserved FDB slots for the highest six classes (P2-P7).
The MVTX2603 does provide a system-wide option of permitting normal QoS scheduling (and buffer use) for
frames originating from flow control enabled ports. When this programmable option is active, it is possible that
some packets may be dropped, even though flow control is on. The reason is that intelligent packet dropping is a
major component of the MVTX2603’s approach to ensuring bounded delay and minimum bandwidth for high priority
flows.
7.9.1
Unicast Flow Control
For unicast frames, flow control is triggered by source port resource availability. Recall that the MVTX2603’s buffer
management scheme allocates a reserved number of FDB slots for each source port. If a programmed number of a
source port’s reserved FDB slots have been used, then flow control Xoff is triggered.
Xon is triggered when a port is currently being flow controlled, and all of that port’s reserved FDB slots have been
released.
Note that the MVTX2603’s per-source-port FDB reservations assure that a source port that sends a single frame to
a congested destination will not be flow controlled.
7.9.2
Multicast Flow Control
In unmanaged mode, flow control for multicast frames is triggered by a global buffer counter. When the system
exceeds a programmable threshold of multicast packets, Xoff is triggered. Xon is triggered when the system returns
below this threshold.
In managed mode, per-VLAN flow control is used for multicast frames. In this case, flow control is triggered by
congestion at the destination. How so? The MVTX2603 checks each destination to which a multicast packet is
headed. For each destination port, the occupancy of the lowest-priority transmission multicast queue (measured in
number of frames) is compared against a programmable congestion threshold. If congestion is detected at even
one of the packet’s destinations then Xoff is triggered.
In addition, each source port has a 26-bit port map recording which port or ports of the multicast frame’s fanout
were congested at the time Xoff was triggered. All ports are continuously monitored for congestion, and a port is
identified as uncongested when its queue occupancy falls below a fixed threshold. When all those ports that were
originally marked as congested in the port map have become uncongested, then Xon is triggered and the 26-bit
vector is reset to zero.
31
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
The MVTX2603 also provides the option of disabling VLAN multicast flow control.
Note: If per-Port flow control is on, QoS performance will be affected. To determine the most efficient way to
program, please refer to the QoS Application Note.
7.10
Mapping to IETF Diffserv Classes
The mapping between priority classes discussed in this chapter and elsewhere is shown below.
VTX
P7
P6
P5
P4
P3
P2
P1
P0
IETF
NM
EF
AF0
AF1
AF2
AF3
BE0
BE1
Table 10 - Mapping between MVTX2603 and IETF Diffserv Classes for Gigabit Ports
As the table illustrates, P7 is used solely for network management (NM) frames. P6 is used for expedited
forwarding service (EF). Classes P2 through P5 correspond to an assured forwarding (AF) group of size 4. Finally,
P0 and P1 are two best effort (BE) classes.
For 10/100 Mbps ports, the classes of Table 12 are merged in pairs—one class corresponding to NM+EF, two AF
classes, and a single BE class.
VTX
P3
P2
P1
P0
IETF
NM+EF
AF0
AF1
BE0
Table 11 - Mapping between MVTX2603 and IETF Diffserv Classes for 10/100 Ports
Features of the MVTX2603 that correspond to the requirements of their associated IETF classes are summarized in
the table below.
Network management (NM) and
Expedited forwarding (EF)
•
•
•
•
Global buffer reservation for NM and EF
Shaper for EF traffic on 1 Gbps ports
Option of strict priority scheduling
No dropping if admission controlled
Assured forwarding (AF)
•
•
•
Four AF classes for 1 Gbps ports
Programmable bandwidth partition, with option of WFQ service
Option of delay-bounded service keeps delay under fixed levels even
if not admission-controlled
Random early discard, with programmable levels
Global buffer reservation for each AF class
•
•
Best effort (BE)
•
•
•
•
Two BE classes for 1 Gbps ports
Service only when other queues are idle means that QoS not
adversely affected
Random early discard, with programmable levels
Traffic from flow control enabled ports automatically classified as BE
Table 12 - MVTX2603 Features Enabling IETF Diffserv Standards
32
Zarlink Semiconductor Inc.
MVTX2603
8.0
Port Trunking
8.1
Features and Restrictions
Data Sheet
A port group (i.e., trunk) can include up to 4 physical ports but all of the ports in a group must be in the same
MVTX2603.
The two Gigabit ports may also be trunked together. There are three trunk groups total including the option to trunk
Gigabit ports.
Load distribution among the ports in a trunk for unicast is performed using hashing based on source MAC address
and destination MAC address. Three other options include source MAC address only, destination MAC address
only and source port (in bidirectional ring mode only). Load distribution for multicast is performed similarly.
If a VLAN includes any of the ports in a trunk group, all the ports in that trunk group should be in the same VLAN
member map.
The MVTX2603 also provides a safe fail-over mode for port trunking automatically. If one of the ports in the trunking
group goes down, the MVTX2603 will automatically redistribute the traffic over to the remaining ports in the trunk.
8.2
Unicast Packet Forwarding
The search engine finds the destination MCT entry, and if the status field says that the destination port found
belongs to a trunk, then the group number is retrieved instead of the port number. In addition, if the source address
belongs to a trunk, then the source port’s trunk membership register is checked.
A hash key, based on some combination of the source and destination MAC addresses for the current packet
selects the appropriate forwarding port.
8.3
Multicast Packet Forwarding
For multicast packet forwarding, the device must determine the proper set of ports from which to transmit the
packet based on the VLAN index and hash key.
Two functions are required in order to distribute multicast packets to the appropriate destination ports in a port
trunking environment.
Determining one forwarding port per group. For multicast packets, all but one port per group, the forwarding port,
must be excluded. Preventing the multicast packet from looping back to the source trunk.
The search engine needs to prevent a multicast packet from sending to a port that is in the same trunk group with
the source port. This is because, when we select the primary forwarding port for each group, we do not take the
source port into account. To prevent this, we simply apply one additional filter, so as to block that forwarding port for
this multicast packet.
33
Zarlink Semiconductor Inc.
MVTX2603
8.4
Data Sheet
Trunking
3 trunk groups are supported. Groups 0 and 1 can trunk up to 4 10/100 ports. Group 2 can trunk 2 Gigabit ports.
The supported combinations are shown in the following table.
Group 0
Port 0
Port 1
Port 2
Port 3
X
X
X
X
X
X
X
X
X
Port 4
Port 5
Port 6
Port 7
X
X
X
X
X
X
Select via trunk0_mode register
Group 1
Select via trunk1_mode register
Group 2
Port 25(Giga 0)
Port 26 (Giga 1)
X
X
The trunks are individually enabled/disabled by controlling pin trunk 0, 1, 2.
9.0
Port Mirroring
9.1
Port Mirroring Features
The received or transmitted data of any 10/100 port in the MVTX2603 chip can be “mirrored” to any other port. We
support two such mirrored source-destination pairs. A mirror port cannot also serve as a data port. Please refer to
the Port Mirroring Application Note for further details.
9.2
•
•
•
•
Setting Registers for Port Mirroring
MIRROR1_SRC: Sets the source port for the first port mirroring pair. Bits [4:0] select the source port to be
mirrored. An illegal port number is used to disable mirroring (which is the default setting). Bit [5] is used to
select between ingress (Rx) or egress (Tx) data.
MIRROR1_DEST: Sets the destination port for the first port mirroring pair. Bits [4:0] select the destination
port to be mirrored. The default is port 23.
MIRROR2_SRC: Sets the source port for the second port mirroring pair. Bits [4:0] select the source port to
be mirrored. An illegal port number is used to disable mirroring (which is the default setting). Bit [5] is used
to select between ingress (Rx) or egress (Tx) data.
MIRROR2_DEST: Sets the destination port for the second port mirroring pair. Bits [4:0] select the
destination port to be mirrored. The default is port 0.
34
Zarlink Semiconductor Inc.
MVTX2603
10.0
Data Sheet
TBI Interface
The TBI interface can be used for 1000Mbps fiber operation. In this mode, the MVTX2603 is connected to the
Serdes as shown in Figure 14. There are two TBI interfaces in the MVTX2603 devices. To enable to TBI function,
the corresponding TXEN and TXER pins need to be boot strapped. See Ball – Signal Description for details.
T[9:0]
M25/26_TXD[9:0]
REFCLK
M25/26_TXCLK
MVTX2603
SERDES
M25/26_RXD[9:0]
R[9:0]
M25/26_RXCLK
RBC0
M25/26_COL
RBC1
Figure 14 - TBI Connection
35
Zarlink Semiconductor Inc.
MVTX2603
11.0
GPSI (7WS) Interface
11.1
GPSI Connection
Data Sheet
The 10/100 RMII ethernet port can function in GPSI (7WS) mode when the corresponding TXEN pin is strapped
low with a 1 K pull down resistor. In this mode, the TXD[0], TXD[1], RXD[0] and RXD[1] serve as TX data, TX clock,
RX data and RX clock respectively. The link status and collision from the PHY are multiplexed and shifted into the
switch device through external glue logic. The duplex of the port can be controlled by programming the ECR
register.
The GPSI interface can be operated in port based VLAN mode only
CRS_DV
RXD[0]
RXD[1]
TXD[1]
TXD[0]
TXEN
crs
rxd
rx_clk
tx_clk
link0
Port 0
Ethernet
PHY
col0
txd
txen
link1
260X
link2
col1
col2
SCAN_LINK
SCAN_CLK
SCAN_COL
link23
col23
Port 23
Ethernet
PHY
Link
Serializer
(CPLD)
Collision
Serializer
(CPLD)
Figure 15 - GPSI (7WS) Mode Connection Diagram
36
Zarlink Semiconductor Inc.
MVTX2603
11.2
Data Sheet
SCAN LINK and SCAN COL interface
An external CPLD logic is required to take the link signals and collision signals from the GPSI PHYs and shift them
into the switch device. The switch device will drive out a signature to indicate the start of the sequence. After that,
the CPLD should shift in the link and collision status of the PHYS as shown in the figure. The extra link status
indicates the polarity of the link signal. One indicates the polarity of the link signal is active high.
scan_clk
scan_link/
scan_col
25 cycles for link/
24 cycles for col
Drived by VTX260x
Driven by MVTX260x
Drived by
Driven
byCPLD
CPLD
Total
32 32
cycles
period
Total
cycles
period
Figure 16 - SCAN LINK and SCAN COLLISON Status Diagram
12.0
LED Interface
12.1
LED Interface Introduction
A serial output channel provides port status information from the MVTX2603 chips. It requires three additional pins:
•
•
•
LED_CLK at 12.5 MHz
LED_SYN a sync pulse that defines the boundary between status frames
LED_DATA a continuous serial stream of data for all status LEDs that repeats once every frame time
A non-serial interface is also allowed, but in this case, only the Gigabit ports will have status LEDs.
A low cost external device (44 pin PAL) is used to decode the serial data and to drive an LED array for display. This
device can be customized for different needs.
12.2
Port Status
In the MVTX2603, each port has 8 status indicators, each represented by a single bit. The 8 LED status indicators
are
•
•
•
•
•
•
•
•
Bit
Bit
Bit
Bit
Bit
Bit
Bit
Bit
0: Flow control
1:Transmit data
2: Receive data
3: Activity (where activity includes either transmission or reception of data)
4: Link up
5: Speed (1= 100 Mb/s; 0= 10 Mb/s)
6: Full-duplex
7: Collision
Eight clocks are required to cycle through the eight status bits for each port.
37
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
When the LED_SYN pulse is asserted, the LED interface will present 256 LED clock cycles with the clock cycles
providing information for the following ports.
Port 0 (10/100): cycles #0 to cycle #7
Port 1 (10/100): cycles#8 to cycle #15
Port 2 (10/100): cycle #16 to cycle #23
...
Port 22 (10/100): cycle #176 to cycle #183
Port 23 (10/100): cycle #184 to cycle #191
Port 24 (Gigabit 0): cycle #192 to cycle #199
Port 25 (Gigabit 1): cycle #200 to cycle #207
Byte 26 (additional status): cycle #208 to cycle #215
Byte 27 (additional status): cycle #216 to cycle #223
Cycles #224 to 256 present data with a value of zero.
The first two bits of byte 26 provides the speed information for the Gigabit ports while the remainder of byte 26 and
byte 27 provides bit status
•
•
•
•
•
•
•
•
•
•
26[0]: G0 port (1= port 24 is operating at Gigabit speed; 0= speed is either 10 or 100 Mb/s depending on
speed bit of Port 24)
26[1]: G1 port (1= port 25 is operating at Gigabit speed; 0= speed is either 10 or 100 Mb/s depending on
speed bit of Port 25)
26[2]: initialization done
26[3]: initialization start
26[4]: checksum ok
26[5]: link_init_complete
26[6]: bist_fail
26[7]: ram_error
27[0]: bist_in_process
27[1]: bist_done
12.3
LED Interface Timing Diagram
The signal from the MVTX2603 to the LED decoder is shown in Figure 17.
Figure 17 - Timing Diagram of LED Interface
38
Zarlink Semiconductor Inc.
MVTX2603
13.0
Register Definition
13.1
MVTX2603 Register Description
Register
CPU Addr
(Hex)
Description
Data Sheet
R/W
I2C Addr
(Hex)
Default
0. ETHERNET Port Control Registers Substitute [N] with Port number (0..17h, 19h, 1Ah)
ECR1P”N”
Port Control Register 1 for Port N
0000 + 2 x N
R/W
000-018
020
ECR2P”N”
Port Control Register 2 for Port N
001 + 2 x N
R/W
01B-033
000
1. VLAN Control Registers Substitute [N] with Port number (0..17h, 19h, 1Ah)
AVTCL
VLAN Type Code Register Low
100
R/W
036
000
AVTCH
VLAN Type Code Register High
101
R/W
037
081
PVMAP”N”_0
Port “N” Configuration Register 0
102 + 4N
R/W
038-052
0FF
PVMAP”N”_1
Port “N” Configuration Register 1
103 + 4N
R/W
053-06D
0FF
PVMAP”N”_2
Port “N” Configuration Register 2
104 + 4N
R/W
06E-088
0FF
PVMAP”N”_3
Port “N” Configuration Register 3
105 + 4N
R/W
089-0A3
007
PVMODE
VLAN Operating Mode
170
R/W
0A4
000
2. TRUNK Control Registers
TRUNK0_ MODE
Trunk Group 0 Mode
203
R/W
0A5
003
TRUNK1_ MODE
Trunk Group 1 Mode
20B
R/W
0A6
003
TRUNK2_ MODE
Trunk Group 2 Mode
210
R/W
NA
003
TX_AGE
Transmission Queue Aging Time
325
R/W
0A7
008
3. Search Engine Configurations
AGETIME_LOW
MAC Address Aging Time Low
400
R/W
0A8
2M:05C/
4M:02E
AGETIME_ HIGH
MAC Address Aging Time High
401
R/W
0A9
000
SE_OPMODE
Search Engine Operating Mode
403
R/W
NA
000
4. Buffer Control and QOS Control
FCBAT
FCB Aging Timer
500
R/W
0AA
0FF
QOSC
QOS Control
501
R/W
0AB
000
FCR
Flooding Control Register
502
R/W
0AC
008
AVPML
VLAN Priority Map Low
503
R/W
0AD
000
AVPMM
VLAN Priority Map Middle
504
R/W
0AE
000
AVPMH
VLAN Priority Map High
505
R/W
0AF
000
TOSPML
TOS Priority Map Low
506
R/W
0B0
000
TOSPMM
TOS Priority Map Middle
507
R/W
0B1
000
39
Zarlink Semiconductor Inc.
Notes
MVTX2603
Register
CPU Addr
(Hex)
Description
Data Sheet
R/W
I2C Addr
(Hex)
Default
TOSPMH
TOS Priority Map High
508
R/W
0B2
000
AVDM
VLAN Discard Map
509
R/W
0B3
000
TOSDML
TOS Discard Map
50A
R/W
0B4
000
BMRC
Broadcast/Multicast Rate Control
50B
R/W
0B5
000
UCC
Unicast Congestion Control
50C
R/W
0B6
2M:008/
4M:010
MCC
Multicast Congestion Control
50D
R/W
0B7
050
PR100
Port Reservation for 10/100 Ports
50E
R/W
0B8
2M:024/
4M:036
SFCB
Share FCB Size
510
R/W
0BA
2M:014/
4M:064
C2RS
Class 2 Reserve Size
511
R/W
0BB
000
C3RS
Class 3 Reserve Size
512
R/W
0BC
000
C4RS
Class 4 Reserve Size
513
R/W
0BD
000
C5RS
Class 5 Reserve Size
514
R/W
0BE
000
C6RS
Class 6 Reserve Size
515
R/W
0BF
000
C7RS
Class 7 Reserve Size
516
R/W
0C0
000
QOSC”N”
QOS Control (N=0 59)
517 512
R/W
0C1-0D2
000
RDRC0
WRED Drop Rate Control 0
553
R/W
0FB
08F
RDRC1
WRED Drop Rate Control 1
554
R/W
0FC
088
USER_
PORT”N”_LOW
User Define Logical Port “N” Low
(N=0-7)
580 + 2N
R/W
0D6-0DD
000
USER_
PORT”N”_HIGH
User Define Logical Port “N” High
581 + 2N
R/W
0DE-0E5
000
USER_ PORT1:0_
PRIORITY
User Define Logic Port 1 and 0 Priority
590
R/W
0E6
000
USER_ PORT3:2_
PRIORITY
User Define Logic Port 3 and 2 Priority
591
R/W
0E7
000
USER_ PORT5:4_
PRIORITY
User Define Logic Port 5 and 4 Priority
592
R/W
0E8
000
USER_
PORT7:6_PRI
ORITY
User Define Logic Port 7 and 6 Priority
593
R/W
0E9
000
USER_PORT_
ENABLE
User Define Logic Port Enable
594
R/W
0EA
000
WLPP10
Well known Logic Port Priority for 1
and 0
595
R/W
0EB
000
WLPP32
Well known Logic Port Priority for 3
and 2
596
R/W
0EC
000
40
Zarlink Semiconductor Inc.
Notes
MVTX2603
Register
CPU Addr
(Hex)
Description
Data Sheet
R/W
I2C Addr
(Hex)
Default
WLPP54
Well known Logic Port Priority for 5
and 4
597
R/W
0ED
000
WLPP76
Well-known Logic Port Priority for 7 & 6
598
R/W
0EE
000
WLPE
Well known Logic Port Enable
599
R/W
0EF
000
RLOWL
User Define Range Low Bit7:0
59A
R/W
0F4
000
RLOWH
User Define Range Low Bit 15:8
59B
R/W
0F5
000
RHIGHL
User Define Range High Bit 7:0
59C
R/W
0D3
000
RHIGHH
User Define Range High Bit 15:8
59D
R/W
0D4
000
RPRIORITY
User Define Range Priority
59E
R/W
0D5
000
5. MISC Configuration Registers
MII_OP0
MII Register Option 0
600
R/W
0F0
000
MII_OP1
MII Register Option 1
601
R/W
0F1
000
FEN
Feature Registers
602
R/W
0F2
010
MIIC0
MII Command Register 0
603
R/W
N/A
000
MIIC1
MII Command Register 1
604
R/W
N/A
000
MIIC2
MII Command Register 2
605
R/W
N/A
000
MIIC3
MII Command Register 3
606
R/W
N/A
000
MIID0
MII Data Register 0
607
RO
N/A
N/A
MIID1
MII Data Register 1
608
RO
N/A
N/A
LED
LED Control Register
609
R/W
0F3
000
SUM
EEPROM Checksum Register
60B
R/W
0FF
000
6. Port Mirroring Controls
MIRROR1_SRC
Port Mirror 1 Source Port
700
R/W
N/A
07F
MIRROR1_ DEST
Port Mirror 1 Destination Port
701
R/W
N/A
017
MIRROR2_SRC
Port Mirror 2 Source Port
702
R/W
N/A
0FF
MIRROR2_ DEST
Port Mirror 2 Destination Port
703
R/W
N/A
000
F. Device Configuration Register
GCR
Global Control Register
F00
R/W
N/A
000
DCR
Device Status and Signature Register
F01
RO
N/A
N/A
DCR1
Giga Port status
F02
RO
N/A
N/A
DPST
Device Port Status Register
F03
R/W
N/A
000
DTST
Data read back register
F04
RO
N/A
N/A
DA
DA Register
FFF
RO
N/A
DA
41
Zarlink Semiconductor Inc.
Notes
MVTX2603
13.2
13.2.1
•
•
Data Sheet
Group 0 Address MAC Ports Group
ECR1Pn: Port N Control Register
I2C
Address h000-01A; CPU Address: 0000+2xN
Accessed by serial interface and I2C (R/W)
7
6
5
Sp State
Bit [0]
4
A-FC
•
•
3
2
1
0
Port Mode
1 - Flow Control Off
0 - Flow Control On
• When Flow Control On:
• In half duplex mode, the MAC transmitter applies back pressure for flow control.
• In full duplex mode, the MAC transmitter sends Flow Control frames when
necessary. The MAC receiver interprets and processes incoming flow control
frames. The Flow Control Frame Received counter is incremented whenever a
flow control is received.
• When Flow Control off:
• In half duplex mode, the MAC Transmitter does not assert flow control by sending
flow control frames or jamming collision.
• In full duplex mode, the Mac transmitter does not send flow control frames. The
MAC receiver does not interpret or process the flow control frames. The Flow
Control Frame Received counter is not incremented.
Bit [1]
•
•
1 - Half Duplex - Only 10/100 mode
0 - Full Duplex
Bit [2]
•
•
1 - 10 Mbps
0 - 100 Mbps
Bit [4:3]
•
•
00 - Automatic Enable Auto Neg. This enables hardware state machine for
auto-negotiation.
01 - Limited Disable auto Neg. This disables hardware for speed autonegotiation. Poll MII for link status.
10 - Link Down. Disable auto Neg. state machine and force link down
(disable the port)
11 - Link Up. User ERC1 [2:0] for config.
•
Asymmetric Flow Control Enable
•
•
Bit [5]
• 0 - Disable asymmetric flow control
• 1 - Enable asymmetric flow control
Bit [7:6]
•
Asymmetric Flow Control Enable. When this bit is set and flow control is on
(bit [0] = 0, don't send out a flow control frame. But MAC receiver interprets
and process flow control frames. Default is 0
•
SS - Spanning tree state Default is 11
•
•
•
•
00 – Blocking: Frame is dropped
01 - Listening:
Frame is dropped
10 - Learning:
Frame is dropped. Source MAC address is learned.
11 - Forwarding: Frame is forwarded. Source MAC address is learned.
42
Zarlink Semiconductor Inc.
MVTX2603
13.2.2
•
•
Data Sheet
ECR2Pn: Port N Control Register
I2C Address: h01B-035; CPU Address: h0001+2xN
Accessed by and serial interface and I2C (R/W)
7
6
5
4
QoS Sel
Bit [0]:
•
3
2
1
0
Reserve
DisL
Ftf
Futf
Filter untagged frame (Default 0)
• 0: Disable
• 1: All untagged frames from this port are discarded
Bit [1]:
•
Filter Tag frame (Default 0)
• 0: Disable
• 1: All tagged frames from this port are discarded
Bit [2]:
•
Learning Disable (Default 0)
• 1 Learning is disabled on this port
• 0 Learning is enabled on this port
Bit [3]:
•
Must be set to ‘1’
Bit [5:4:]
•
•
•
QOS mode selection (Default 00)
Determines which of the 4 sets of QoS settings is used for 10/100 ports.
Note that there are 4 sets of per-queue byte thresholds, and 4 sets of WFQ
ratios programmed. These bits select among the 4 choices for each 10/100
port. Refer to QoS Application Note.
•
•
•
•
Bit [7:6]
13.2.3
•
•
•
00: select class byte limit set 0 and classes WFQ credit set 0
01: select class byte limit set 1 and classes WFQ credit set 1
10: select class byte limit set 2 and classes WFQ credit set 2
11: select class byte limit set 3 and classes WFQ credit set 3
Reserved
GGControl – Extra GIGA Port Control
CPU Address: h036
Accessed by serial interface (R/W)
7
6
DF
Bit [0]:
•
5
4
3
MiiB
RstA
DF
Reset GIGA port A
• 0: Normal operation (default)
• 1: Reset Gigabit port A
Bit [1]:
•
GIGA port A use MII interface (10/100 M)
• 0: Gigabit port operations at 1000 mode
• 1: Gigabit port operations at 10/100 mode
Bit [2]:
•
Reserved - Must be zero
43
Zarlink Semiconductor Inc.
2
1
0
MiiA
RstA
MVTX2603
Bit [3]:
•
Data Sheet
GIGA port A direct flow control (MAC to MAC connection). The MVTX2603
supports direct flow control mechanism, the flow control frame is therefore
not sent through the Gigabit port data path.
• 0: Direct flow control disabled (default)
• 1: Direct flow control enabled
Bit [4]:
•
Reset GIGA port B
• 0: Normal operation (default)
• 1: Reset Gigabit port B
Bit [5]:
•
GIGA port B use MII interface (10/100 M)
• 0: Gigabit port operates at 1000 mode
• 1: Gigabit port operates at 10/100 mode
Bit [6]:
•
Reserved. Must be zero.
Bit [7]:
•
GIGA port B direct flow control (MAC to MAC connection). The MVTX2603
supports direct flow control mechanism, the flow control frame is therefore
not sent through the Gigabit port data path.
• 0: Direct flow control disabled (default)
• 1: Direct flow control enabled
13.3
13.3.1
•
•
Group 1 Address VLAN Group
AVTCL – VLAN Type Code Register Low
I2C Address h036; CPU Address: h100
Accessed by serial interface and I2C (R/W)
Bit [7:0]:
13.3.2
•
•
VLANType_LOW: Lower 8 bits of the VLAN type code (Default 00)
AVTCH – VLAN Type Code Register High
I2C Address h037; CPU Address: h101
Accessed by serial interface and I2C (R/W)
Bit [7:0]:
13.3.3
•
•
•
•
VLANType_HIGH: Upper 8 bits of the VLAN type code (Default is 81)
PVMAP00_0 – Port 00 Configuration Register 0
I2C Address h038, CPU Address: h102
Accessed by serial interface and I2C (R/W)
Bit [7:0]:
•
VLAN Mask for ports 7 to 0 (Default FF)
This register indicates the legal egress ports. A “1” on bit 7 means that the packet can be sent to port 7. A “0” on bit
7 means that any packet destined to port 7 will be discarded. This register works with registers 1, 2 and 3 to form a
27 bit mask to all egress ports.
44
Zarlink Semiconductor Inc.
MVTX2603
13.3.4
•
•
PVMAP00_1 – Port 00 Configuration Register 1
I2C Address h53, CPU Address: h103
Accessed by serial interface and I2C (R/W)
Bit [7:0]:
13.3.5
•
•
•
VLAN Mask for ports 15 to 8 (Default is FF)
PVMAP00_2 – Port 00 Configuration Register 2
I2C Address h6E, CPU Address: h104
Accessed by serial interface and I2C (R/W)
Bit [7:0]:
13.3.6
•
•
Data Sheet
•
VLAN Mask for ports 23 to 16 (Default FF)
PVMAP00_3 – Port 00 Configuration Register 3
I2C Address h89, CPU Address: h105
Accessed by serial interface and I2C (R/W)
7
6
FP en
Drop
5
3
Default tx priority
2
1
0
VLAN Mask
Bit [0]:
Reserved (Default 1)
Bit [2:1]:
VLAN Mask for ports 26 to 25 (Default 3)
Bit [5:1]:
Default Transmit priority. Used when Bit [7] = 1 (Default 0)
• 000 Transmit Priority Level 0 (Lowest)
• 001 Transmit Priority Level 1
• 010 Transmit Priority Level 2
• 011 Transmit Priority Level 3
• 100 Transmit Priority Level 4
• 101 Transmit Priority Level 5
• 110 Transmit Priority Level 6
• 111 Transmit Priority Level 7 (Highest)
Bit [6]:
Default Discard priority (Default 0)
• 0 - Discard Priority Level 0 (Lowest)
• 1 - Discard Priority Level 7(Highest)
Bit [7]:
Enable Fix Priority (Default 0)
• 0 Disable fix priority. All frames are analysed. Transmit Priority and
Discard Priority are based on VLAN Tag, TOS field or Logical Port.
• 1 Transmit Priority and Discard Priority are based on values programmed
in bit [6:3]
45
Zarlink Semiconductor Inc.
MVTX2603
13.4
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Port Configuration Register
PVMAP01_0,1,2,3 I2C Address h39,54,6F,8A; CPU Address:h106,107,108,109)
PVMAP02_0,1,2,3 I2C Address h3A,55,70,8B; CPU Address:h10A, 10B, 10C, 10D)
PVMAP03_0,1,2,3 I2C Address h3B,56,71,8C; CPU Address:h10E, 10F, 110, 111)
PVMAP04_0,1,2,3 I2C Address h3C,57,72,8D; CPU Address:h112, 113, 114, 115)
PVMAP05_0,1,2,3 I2C Address h3D,58,73,8E; CPU Address:h116, 117, 118, 119)
PVMAP06_0,1,2,3 I2C Address h3E,59,74,8F; CPU Address:h11A, 11B, 11C, 11D)
PVMAP07_0,1,2,3 I2C Address h3F,5A,75,90; CPU Address:h11E, 11F, 120, 121)
PVMAP08_0,1,2,3 I2C Address h40,5B,76,91; CPU Address:h122, 123, 124, 125)
PVMAP09_0,1,2,3 I2C Address h41,5C,77,92; CPU Address:h126, 127, 128, 129)
PVMAP10_0,1,2,3 I2C Address h42,5D,78,93; CPU Address:h12A, 12B, 12C, 12D)
PVMAP11_0,1,2,3 I2C Address h43,5E,79,94; CPU Address:h12E, 12F, 130, 131)
PVMAP12_0,1,2,3 I2C Address h44,5F,7A,95; CPU Address:h132, 133, 134, 135)
PVMAP13_0,1,2,3 I2C Address h45,60,7B,96; CPU Address:h136, 137, 138, 139)
PVMAP14_0,1,2,3 I2C Address h46,61,7C,97; CPU Address:h13A, h13B, 13C, 13D)
PVMAP15_0,1,2,3 I2C Address h47,62,7D,98; CPU Address:h13E, 13F, 140, 141)
PVMAP16_0,1,2,3 I2C Address h48,63,7E,99; CPU Address:h142, 143, 144, 145)
PVMAP17_0,1,2,3 I2C Address h49,64,7F,9A; CPU Address:h146, 147, 148, 149)
PVMAP18_0,1,2,3 I2C Address h4A,65,80,9B; CPU Address:h14A, 14B, 14C, 14D)
PVMAP19_0,1,2,3 I2C Address h4B,66,81,9C; CPU Address:h14E, 14F, 150, 151)
PVMAP20_0,1,2,3 I2C Address h4C,67,82,9D; CPU Address:h152, 153, 154, 155)
PVMAP21_0,1,2,3 I2C Address h4D,68,83,9E; CPU Address:h156, 157, 158, 159)
PVMAP22_0,1,2,3 I2C Address h4E,69,84,9F; CPU Address:h15A, 15B, 15C, 15D)
PVMAP23_0,1,2,3 I2C Address h4F,6A,85,A0; CPU Address:h15E, 15F, 160, 161)
PVMAP25_0,1,2,3 I2C Address h51,6C,87,A2; CPU Address:h166, 167, 168, 169) (Gigabit port 1)
PVMAP26_0,1,2,3 I2C Address h52,6D,88,A3; CPU Address:h16A, 16B, 16C, 16D) (Gigabit port 2)
13.4.1
•
•
Data Sheet
PVMODE
I2C
Address: h0A4, CPU Address: h170
Accessed by serial interface, and I2C (R/W)
7
5
4
3
2
1
SM0
rPCS
DF
SL
0
Bit [0]:
•
•
Reserved
Must be ‘0’
Bit [1]:
•
Slow learning
Same function as SE_OP MODE bit 7. Either bit can enable the function; both need to
be turned off to disable the feature.
Bit [2]:
•
Disable dropping of frames with destination MAC addresses 0180C2000001 to
0180C200000F (Default = 0)
• 0: Drop all frames in this range
• 1: Disable dropping of frames in this range
Bit [3]:
• 1: Disable reset PCS
• 0: Enable reset PCS. PCS FIFO will be reset when receiving a PCS symbol error
46
Zarlink Semiconductor Inc.
MVTX2603
Bit [4]:
•
Data Sheet
Support MAC address 0
• 0: MAC address 0 is not learned.
• 1: MAC address 0 is learned.
Bit [7:5]:
13.4.2
•
•
•
Reserved
TRUNK0_MODE– Trunk group 0 mode
I2C Address: h0A5; CPU Address: h203
Accessed by serial interface and I2C (R/W)
7
4
3
2
1
Hash Select
Bit [1:0]:
•
•
Port Select
Port selection in unmanaged mode. Input pin TRUNK0 enable/disable
trunk group 0
•
•
•
•
Bit [3:2]
0
00 Reserved
01 Port 0 and 1 are used for trunk 0
10 Port 0,1 and 2 are used for trunk 0
11 Port 0,1,2 and 3 are used for trunk 0
Hash Select. The Hash selected is valid for Trunk 0, 1 and 2. (Default
00)
•
•
•
•
00 Use Source and Destination Mac Address for hashing
01 Use Source Mac Address for hashing
10 Use Destination Mac Address for hashing
11 Use source destination MAC address and ingress physical port number
for hashing
Note: Trunk group 2 (two gigabit ports) is enabled/disabled using input pin TRUNK2.
13.4.3
•
•
TRUNK1_MODE – Trunk group 1 mode
I2C
Address: h0A6; CPU Address: h20B
Accessed by serial interface and I2C (R/W)
7
2
1
0
Port Select
Bit [1:0]:
•
•
•
•
•
Port selection in unmanaged mode. Input pin TRUNK1
enable/disable trunk group 1
00 Reserved
01 Port 4 and 5 are used for trunk1
10 Reserved
11 Port 4, 5, 6 and 7 are used for trunk1
47
Zarlink Semiconductor Inc.
MVTX2603
13.5
13.5.1
•
•
Data Sheet
Group 4 Address Search Engine Group
TX_AGE – Tx Queue Aging timer
I2C
Address: h07;CPU Address: h325
Accessed by serial interface (RW)
7
6
5
0
Tx Queue Agent
•
•
•
Bit [5:0]: Unit of 100 ms (Default 8)
Disable transmission queue aging if value is zero. Aging timer for all ports and queues.
For no packet loss flow control, this register must be set to 0.
13.5.2
•
•
•
•
I2C Address: h0A8; CPU Address: h400
Accessed by serial interface and I2C (R/W)
Bit [7:0] Low byte of the MAC address aging timer.
MAC address aging is enable/disable by boot strap TSTOUT9
13.5.3
•
•
•
•
•
AGETIME_HIGH –MAC address aging time High
I2C Address: h0A9; CPU Address: h401
Accessed by serial interface and I2C (R/W)
Bit [7:0]: High byte of the MAC address aging timer.
The default setting provide 300 seconds aging time. Aging time is based on the following equation:
{AGETIME_HIGH,AGETIME_LOW} X (# of MAC address entries in the memory x 100 µsec). Number of
MAC entries = 32 K when 1 MB is used per bank. Number of MAC entries = 64 K when 2 MB is used per
bank.
13.5.4
•
•
•
AGETIME_LOW – MAC address aging time Low
SE_OPMODE – Search Engine Operation Mode
CPU Address: h403
Accessed by serial interface (R/W)
{SE_OPMODE} X(# of entries 100 usec)
7
6
5
SL
DMS
0
Bit [5:0]:
•
Reserved
Bit [6]:
•
Disable MCT speedup aging
• 1 – Disable speedup aging when MCT resource is low.
• 0 – Enable speedup aging when MCT resource is low.
Bit [7]:
•
Slow Learning
• 1– Enable slow learning. Learning is temporary disabled when search
demand is high
• 0 – Learning is performed independent of search demand
48
Zarlink Semiconductor Inc.
MVTX2603
13.6
13.6.1
•
I2C
Data Sheet
Group 5 Address Buffer Control/QOS Group
FCBAT – FCB Aging Timer
Address: h0AA; CPU Address: h500
7
0
FCBAT
Bit [7:0]:
13.6.2
•
•
•
•
FCB Aging time. Unit of 1ms. (Default FF)
This function is for buffer aging control. It is used to configure the aging
time, and can be enabled/ disabled through bootstrap pin. It is not
recommended to use this function for normal operation.
QOSC – QOS Control
I2C Address: h0AB; CPU Address: h501
Accessed by serial interface and I2C (R/W)
7
6
Tos-d
Tos-p
5
4
3
1
VF1c
0
L
Bit [0]:
•
QoS frame lost is OK. Priority will be available for flow control enabled
source only when this bit is set (Default 0)
Bit [4]:
•
Per VLAN Multicast Flow Control (Default 0)
• 0 - Disable
• 1 - Enable
Bit [5]:
•
Reserved
Bit [6]:
•
Select TOS bits for Priority (Default 0)
• 0 - Use TOS [4:2] bits to map the transmit priority
• 1 - Use TOS [7:5] bits to map the transmit priority
Bit [7]:
•
Select TOS bits for Drop Priority (Default 0)
• 0 - Use TOS[4:2] bits to map the drop priority
• 1 - Use TOS[7:5] bits to map the drop priority
13.6.3
•
•
FCR – Flooding Control Register
I2C Address: h0AC; CPU Address: h502
Accessed by serial interface and I2C (R/W)
7
6
Tos
4
3
TimeBase
0
U2MR
49
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
Bit [3:0]:
•
U2MR: Unicast to Multicast Rate. Units in terms of time base defined in
bits [6:4]. This is used to limit the amount of flooding traffic. The value
in U2MR specifies how many packets are allowed to flood within the
time specified by bit [6:4]. To disable this function, program U2MR to 0.
(Default = 8)
Bit [6:4]:
•
TimeBase:
000 = 100 us
001 = 200 us
010 = 400 us
011 = 800 us
100 = 1.6 ms
101 = 3.2 ms
110 = 6.4 ms
111 = 100 us (same as 000)
Bit [7]:
•
(Default = 000)
•
Select VLAN tag or TOS (IP packets) to be preferentially picked to map
transmit priority and drop priority (Default = 0).
• 0 – Select VLAN Tag priority field over TOS
• 1 – Select TOS over VLAN tag priority field
13.6.4
•
•
AVPML – VLAN Priority Map
I2C
Address: h0AD; CPU Address: h503
Accessed by serial interface and I2C (R/W)
7
6
VP2
5
3
2
VP1
0
VP0
Registers AVPML, AVPMM, and AVPMH allow the eight VLAN priorities to map into eight internal level transmit
priorities. Under the internal transmit priority, seven is highest priority where as zero is the lowest. This feature
allows the user the flexibility of redefining the VLAN priority field. For example, programming a value of 7 into bit 2:0
of the AVPML register would map VLAN priority 0 into internal transmit priority 7. The new priority is used inside the
2603. When the packet goes out it carries the original priority.
Bit [2:0]:
•
Priority when the VLAN tag priority field is 0 (Default 0)
Bit [5:3]:
•
Priority when the VLAN tag priority field is 1 (Default 0)
Bit [7:6]:
•
Priority when the VLAN tag priority field is 2 (Default 0)
50
Zarlink Semiconductor Inc.
MVTX2603
13.6.5
•
•
Data Sheet
AVPMM – VLAN Priority Map
I2C Address: h0AE, CPU Address: h504
Accessed by serial interface and I2C (R/W)
7
6
VP5
4
3
VP4
1
0
VP3
VP2
Map VLAN priority into eight level transmit priorities:
13.6.6
•
•
Bit [0]:
•
Priority when the VLAN tag priority field is 2 (Default 0)
Bit [3:1]:
•
Priority when the VLAN tag priority field is 3 (Default 0)
Bit [6:4]:
•
Priority when the VLAN tag priority field is 4 (Default 0)
Bit [7]:
•
Priority when the VLAN tag priority field is 5 (Default 0)
AVPMH – VLAN Priority Map
I2C
Address: h0AF, CPU Address: h505
Accessed by serial interface and I2C (R/W)
7
5
4
2
VP7
1
VP6
0
VP5
Map VLAN priority into eight level transmit priorities:
13.6.7
•
•
Bit [1:0]:
•
Priority when the VLAN tag priority field is 5 (Default 0)
Bit [4:2]:
•
Priority when the VLAN tag priority field is 6 (Default 0)
Bit [7:5]:
•
Priority when the VLAN tag priority field is 7 (Default 0)
TOSPML – TOS Priority Map
I2C
Address: h0B0, CPU Address: h506
Accessed by serial interface and I2C (R/W)
7
6
TP2
5
3
2
TP1
Map TOS field in IP packet into eight level transmit priorities:
Bit [2:0]:
•
Priority when the TOS field is 0 (Default 0)
Bit [5:3]:
•
Priority when the TOS field is 1 (Default 0)
Bit [7:6]:
Priority when the TOS field is 2 (Default 0)
51
Zarlink Semiconductor Inc.
0
TP0
MVTX2603
13.6.8
•
•
Data Sheet
TOSPMM – TOS Priority Map
I2C Address: h0B1, CPU Address: h507
Accessed by serial interface and I2C (R/W)
7
6
4
TP5
3
TP4
1
TP3
0
TP2
Map TOS field in IP packet into four level transmit priorities:
13.6.9
•
•
Bit [0]:
•
Priority when the TOS field is 2 (Default 0)
Bit [3:1]:
•
Priority when the TOS field is 3 (Default 0)
Bit [6:4]:
•
Priority when the TOS field is 4 (Default 0)
Bit [7]:
•
Priority when the TOS field is 5 (Default 0)
TOSPMH – TOS Priority Map
I2C
Address: h0B2, CPU Address: h508
Accessed by serial interface and I2C (R/W)
7
5
4
2
TP7
1
TP6
0
TP5
Map TOS field in IP packet into four level transmit priorities:
13.6.10
•
•
Bit [1:0]:
•
Priority when the TOS field is 5 (Default 0)
Bit [4:2]:
•
Priority when the TOS field is 6 (Default 0)
Bit [7:5]:
•
Priority when the TOS field is 7 (Default 0)
AVDM – VLAN Discard Map
I2C
Address: h0B3, CPU Address: h509
Accessed by serial interface and I2C (R/W)
7
FDV7
6
5
4
3
2
1
0
FDV6
FDV5
FDV4
FDV3
FDV2
FDV1
FDV0
Map VLAN priority into frame discard when low priority buffer usage is above threshold
Bit [0]:
•
Frame drop priority when VLAN tag priority field is 0 (Default 0)
Bit [1]:
•
Frame drop priority when VLAN tag priority field is 1 (Default 0)
Bit [2]:
•
Frame drop priority when VLAN tag priority field is 2 (Default 0)
Bit [3]:
•
Frame drop priority when VLAN tag priority field is 3 (Default 0)
52
Zarlink Semiconductor Inc.
MVTX2603
13.6.11
•
•
Data Sheet
Bit [4]:
•
Frame drop priority when VLAN tag priority field is 4 (Default 0)
Bit [5]:
•
Frame drop priority when VLAN tag priority field is 5 (Default 0)
Bit [6]:
•
Frame drop priority when VLAN tag priority field is 6 (Default 0)
Bit [7]:
•
Frame drop priority when VLAN tag priority field is 7 (Default 0)
TOSDML – TOS Discard Map
I2C
Address: h0B4, CPU Address: h50A
Accessed by serial interface and I2C (R/W)
7
6
5
4
3
2
1
0
FDT7
FDT6
FDT5
FDT4
FDT3
FDT2
FDT1
FDT0
Map TOS into frame discard when low priority buffer usage is above threshold
13.6.12
•
•
Bit [0]:
•
Frame drop priority when TOS field is 0 (Default 0)
Bit [1]:
•
Frame drop priority when TOS field is 1 (Default 0)
Bit [2]:
•
Frame drop priority when TOS field is 2 (Default 0)
Bit [3]:
•
Frame drop priority when TOS field is 3 (Default 0)
Bit [4]:
•
Frame drop priority when TOS field is 4 (Default 0)
Bit [5]:
•
Frame drop priority when TOS field is 5 (Default 0)
Bit [6]:
•
Frame drop priority when TOS field is 6 (Default 0)
Bit [7]:
•
Frame drop priority when TOS field is 7 (Default 0)
BMRC - Broadcast/Multicast Rate Control
I2C Address: h0B5, CPU Address: h50B
Accessed by serial interface and I2C (R/W)
7
4
3
Broadcast Rate
•
0
Multicast Rate
This broadcast and multicast rate defines for each port the number of packet allowed to be forwarded within
a specified time. Once the packet rate is reached, packets will be dropped. To turn off the rate limit,
program the field to 0. Timebase is based on register 502 [6:4].
Bit [3:0]:
•
Multicast Rate Control Number of multicast packets allowed within the
time defined in bits 6 to 4 of the Flooding Control Register (FCR).
(Default 0).
Bit [7:4]:
•
Broadcast Rate Control Number of broadcast packets allowed within
the time defined in bits 6 to 4 of the Flooding Control Register (FCR).
(Default 0)
53
Zarlink Semiconductor Inc.
MVTX2603
13.6.13
•
•
Data Sheet
UCC – Unicast Congestion Control
I2C Address: h0B6, CPU Address: h50C
Accessed by serial interface and I2C (R/W)
7
0
Unicast congest threshold
Bit [7:0]:
13.6.14
•
•
•
Number of frame count. Used for best effort dropping at B% when
destination port’s best effort queue reaches UCC threshold and shared
pool is all in use. Granularity 1 frame. (Default: h10 for 2 MB/bank or
h08 for 1 MB/bank)
MCC – Multicast Congestion Control
I2C
Address: h0B7, CPU Address: h50D
Accessed by serial interface and I2C (R/W)
7
5
4
0
FC reaction prd
13.6.15
•
•
Multicast congest threshold
Bit [4:0]:
•
In multiples of two. Used for triggering MC flow control when
destination multicast port’s best effort queue reaches MCC threshold.
(Default 0x10)
Bit [7:5]:
•
Flow control reaction period (Default 2) Granularity 4 uSec.
PR100 – Port Reservation for 10/100 ports
I2C Address: h0B8, CPU Address: h50E
Accessed by serial interface and I2C (R/W)
7
4
3
Buffer low thd
0
SP Buffer reservation
Bit [3:0]:
•
•
Per port buffer reservation.
Define the space in the FDB reserved for each 10/100 port. Expressed
in multiples of 4 packets. For each packet 1536 bytes are reserved in
the memory.
Bits [7:4]:
•
Expressed in multiples of 4 packets. Threshold for dropping all best
effort frames when destination port best efforts queues reach UCC
threshold and shared pool all used and source port reservation is at or
below the PR100[7:4] level. Also the threshold for initiating UC flow
control.
Default:
•
• h36 for 24+2 configuration with memory 2 MB/bank;
• h24 for 24+2 configuration with 1 MB/bank;
54
Zarlink Semiconductor Inc.
MVTX2603
13.6.16
•
•
Data Sheet
PRG – Port Reservation for Giga ports
I2C Address: h0B9, CPU Address: h50F
Accessed by serial interface and I2C (R/W)
7
3
Buffer low thd
0
SP buffer reservation
Bit [3:0]:
•
•
Per source port buffer reservation.
Define the space in the FDB reserved for each Gigabit port. Expressed
in multiples of 16 packets. For each packet 1536 bytes are reserved in
the memory.
Bits [7:4]:
•
Expressed in multiples of 16 packets. Threshold for dropping all best
effort frames when destination port best effort queues reach UCC
threshold and shared pool is all used and source port reservation is at
or below the PRG[7:4] level. Also the threshold for initiating UC flow
control.
Default:
•
• H58 for memory 2 MB/bank;
• H35 for 1 MB/bank;
13.6.17
•
•
SFCB – Share FCB Size
I2C Address: h0BA, CPU Address: h510
Accessed by serial interface and I2C (R/W)
7
0
Shared buffer size
Bits [7:0]:
•
•
Expressed in multiples of 4 packets. Buffer reservation for shared pool.
Default:
• h64 for 24+2 configuration with memory of 2 MB/bank;
• h14 for 24+2 configuration with memory of 1 MB/bank;
13.6.18
•
•
C2RS – Class 2 Reserve Size
I2C Address: h0BB, CPU Address: h511
Accessed by serial interface and I2C (R/W)
7
0
Class 2 FCB Reservation
•
Buffer reservation for class 2 (third lowest priority). Granularity 1. (Default 0)
55
Zarlink Semiconductor Inc.
MVTX2603
13.6.19
•
•
Data Sheet
C3RS – Class 3 Reserve Size
I2C Address: h0BC, CPU Address: h512
Accessed by serial interface and I2C (R/W)
7
0
Class 3 FCB Reservation
•
Buffer reservation for class 3. Granularity 1. (Default 0)
13.6.20
•
•
C4RS – Class 4 Reserve Size
I2C
Address: h0BD, CPU Address: h513
Accessed by serial interface and I2C (R/W)
7
0
Class 4 FCB Reservation
•
Buffer reservation for class 4. Granularity 1. (Default 0)
13.6.21
•
•
C5RS – Class 5 Reserve Size
I2C Address: h0BE; CPU Address: h514
Accessed by serial interface and I2C (R/W)
7
0
Class 5 FCB Reservation
•
Buffer reservation for class 5. Granularity 1. (Default 0)
13.6.22
•
•
C6RS – Class 6 Reserve Size
I2C Address: h0BF; CPU Address h515
Accessed by serial interface and I2C (R/W)
7
0
Class 6 FCB Reservation
•
Buffer reservation for class 6 (second highest priority). Granularity 1. (Default 0)
13.6.23
•
•
C7RS – Class 7 Reserve Size
I2C
Address: h0C0; CPU Address: h516
Accessed by serial interface and I2C (R/W)
7
0
Class 7 FCB Reservation
•
Buffer reservation for class 7 (highest priority). Granularity 1. (Default 0)
56
Zarlink Semiconductor Inc.
MVTX2603
13.6.24
•
•
•
•
Data Sheet
Classes Byte Limit Set 0
Accessed by serial interface and I2C (R/W)
C — QOSC00 – BYTE_C01 (I2C Address h0C1, CPU Address 517)
B — QOSC01 – BYTE_C02 (I2C Address h0C2, CPU Address 518)
A — QOSC02 – BYTE_C03 (I2C Address h0C3, CPU Address 519)
QOSC00 through QOSC02 represents one set of values A-C for a 10/100 port when using the Weighted Random
Early Drop (WRED) Scheme described in Chapter 7.7. There are four such sets of values A-C specified in Classes
Byte Limit Set 0, 1, 2 and 3.
Each 10/ 100 port can choose one of the four Byte Limit Sets as specified by the QoS Select field located in bits 5
to 4 of the ECR2n register. The values A-C are per-queue byte thresholds for random early drop. QOSC02
represents A, and QOSC00 represents C.
Granularity when Delay bound is used: QOSC02: 128 bytes, QOSC01: 256 bytes. QOSC00: 512 bytes. Granularity
when WFQ is used: QOSC02: 512 bytes, QOSC01: 512 bytes, QOSC00: 512 bytes.
13.6.25
•
Classes Byte Limit Set 1
Accessed by serial interface and I2C (R/W)
C - QOSC03 – BYTE_C11 (I2C Address h0C4, CPU Address 51a)
B - QOSC04 – BYTE_C12 (I2C Address h0C5, CPU Address 51b)
A - QOSC05 – BYTE_C13 (I2C Address h0C6, CPU Address 51c)
QOSC03 through QOSC05 represents one set of values A-C for a 10/100 port when using the Weighted Random
Early Detect (WRED) Scheme.
Granularity when Delay bound is used: QOSC05: 128 bytes, QOSC04: 256 bytes. QOSC03: 512 bytes. Granularity
when WFQ is used: QOSC05: 512 bytes, QOSC04: 512 bytes, QOSC03: 512 bytes.
13.6.26
•
Classes Byte Limit Set 2
Accessed by serial interface and I2C (R/W)
C - QOSC06 – BYTE_C21 (CPU Address 51d)
B - QOSC07 – BYTE_C22 (CPU Address 51e)
A - QOSC08 – BYTE_C23 (CPU Address 51f)
QOSC06 through QOSC08 represents one set of values A-C for a 10/100 port when using the Weighted Random
Early Detect (WRED) Scheme.
Granularity when Delay bound is used: QOSC08: 128 bytes, QOSC07: 256 bytes. QOSC06: 512 bytes. Granularity
when WFQ is used: QOSC08: 512 bytes, QOSC07: 512 bytes, QOSC06: 512 bytes.
13.6.27
•
Classes Byte Limit Set 3
Accessed by serial interface and I2C (R/W)
C - QOSC09 – BYTE_C31 (CPU Address 520)
B - QOSC10 – BYTE_C32 (CPU Address 521)
A - QOSC11 – BYTE_C33 (CPU Address 522)
QOSC09 through QOSC011 represents one set of values A-C for a 10/100 port when using the Weighted Random
Early Detect (WRED) Scheme.
57
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
Granularity when Delay bound is used: QOSC11: 128 bytes, QOSC10: 256 bytes. QOSC09: 512 bytes. Granularity
when WFQ is used: QOSC11: 512 bytes, QOSC10: 512 bytes, QOSC09: 512 bytes.
13.6.28
•
Classes Byte Limit Giga Port 1
Accessed by serial interface and I2C (R/W)
F - QOSC12 – BYTE_C2_G1 (I2C Address h0C7, CPU Address 523)
E - QOSC13 – BYTE_C3_G1 (I2C Address h0C8, CPU Address 524)
D - QOSC14 – BYTE_C4_G1 (I2C Address h0C9, CPU Address 525)
C - QOSC15 – BYTE_C5_G1 (I2C Address h0CA, CPU Address 526)
B - QOSC16 – BYTE_C6_G1 (I2C Address h0CB, CPU Address 527)
A - QOSC17 – BYTE_C7_G1 (I2C Address h0CC, CPU Address 528)
QOSC12 through QOSC17 represent the values A-F for Gigabit port 24. They are per-queue byte thresholds for
random early drop. QOSC17 represents A, and QOSC12 represents F.
Granularity when Delay bound is used: QOSC17 and QOSC16: 256 bytes, QOSC15 and QOSC14: 512 bytes,
QOSC13 and QOSC12: 1024 bytes.
Granularity when WFQ is used: QOSC17 to QOSC12: 1024 bytes
13.6.29
•
Classes Byte Limit Giga Port 2
Accessed by serial interface and I2C (R/W)
F - QOSC18 – BYTE_C2_G2 (I2C Address h0CD, CPU Address 529)
E - QOSC19 – BYTE_C3_G2 (I2C Address h0CE, CPU Address 52a)
D - QOSC20 – BYTE_C4_G2 (I2C Address h0CF, CPU Address 52b)
C - QOSC21 – BYTE_C5_G2 (I2C Address h0D0, CPU Address 52c)
B - QOSC22 – BYTE_C6_G2 (I2C Address h0D1, CPU Address 52d)
A - QOSC23 – BYTE_C7_G2 (I2C Address h0D2, CPU Address 52e)
QOSC18 through QOSC23 represent the values A-F for Gigabit port 2. They are per-queue byte thresholds for
random early drop. QOSC23 represents A, and QOSC18 represents F.
Granularity when Delay Bound is used: QOSC23 and QOSC22: 256 bytes, QOSC21 and QOSC20: 512 bytes,
QOSC19 and QOSC18: 1024 bytes.
Granularity when WFQ is used: QOSC18 to QOSC23: 1024 bytes
13.6.30
•
Classes WFQ Credit Set 0
Accessed by serial interface (R/W)
W0 - QOSC24[5:0] – CREDIT_C00 (CPU Address 52f)
W1 - QOSC25[5:0] – CREDIT_C01 (CPU Address 530)
W2 - QOSC26[5:0] – CREDIT_C02 (CPU Address 531)
W3 - QOSC27[5:0] – CREDIT_C03 (CPU Address 532)
58
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
QOSC24 through QOSC27 represents one set of WFQ parameters for a 10/100 port. There are four such sets of
values. The granularity of the numbers is 1 and their sum must be 64. QOSC27 corresponds to W3 and QOSC24
corresponds to W0.
•
•
•
QOSC24[7:6]: Priority service type for the ports select this parameter set. Option 1 to 4
QOSC25[7]: Priority service allow flow control for the ports select this parameter set
QOSC25[6]: Flow control pause best effort traffic only
Both flow control allow and flow control best effort only can take effect only the priority type is WFQ.
13.6.31
•
Classes WFQ Credit Set 1
Accessed by serial interface (R/W)
W0 - QOSC28[5:0] – CREDIT_C10 (CPU Address 533)
W1 - QOSC29[5:0] – CREDIT_C11 (CPU Address 534)
W2 - QOSC30[5:0] – CREDIT_C12 (CPU Address 535)
W3 - QOSC31[5:0] – CREDIT_C13 (CPU Address 536)
QOSC28 through QOSC31 represents one set of WFQ parameters for a 10/100 port. There are four such sets of
values. The granularity of the numbers is 1 and their sum must be 64. QOSC31 corresponds to W3 and QOSC28
corresponds to W0.
QOSC28[7:6]: Priority service type for the ports select this parameter set. Option 1 to 4
QOSC29[7]: Priority service allow flow control for the ports select this parameter set
QOSC29[6]: Flow control pause best effort traffic only
13.6.32
•
Classes WFQ Credit Set 2
Accessed by serial interface (R/W)
W0 - QOSC32[5:0] – CREDIT_C20 (CPU Address 537)
W1 - QOSC33[5:0] – CREDIT_C21 (CPU Address 538)
W2 - QOSC34[5:0] – CREDIT_C22 (CPU Address 539)
W3 - QOSC35[5:0] – CREDIT_C23 (CPU Address 53a)
QOSC35 through QOSC32 represents one set of WFQ parameters for a 10/100 port. There are four such sets of
values. The granularity of the numbers is 1 and their sum must be 64. QOSC35 corresponds to W3 and QOSC32
corresponds to W0.
•
•
•
QOSC32[7:6]: Priority service type for the ports select this parameter set. Option 1 to option 4
QOSC33[7]: Priority service allow flow control for the ports select this parameter set
QOSC33[6]: Flow Control pause best effort traffic only
13.6.33
•
Classes WFQ Credit Set 3
Accessed by serial interface (R/W)
W0 - QOSC36[5;0] – CREDIT_C30 (CPU Address 53b)
W1 - QOSC37[5:0] – CREDIT_C31 (CPU Address 53c)
W2 - QOSC38[5:0] – CREDIT_C32 (CPU Address 53d)
W3 - QOSC39[5:0] – CREDIT_C33 (CPU Address 53e)
59
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
QOSC39 through QOSC36 represents one set of WFQ parameters for a 10/100 port. There are four such sets of
values. The granularity of the numbers is 1, and their sum must be 64. QOSC39 corresponds to W3 and QOSC36
corresponds to W0.
•
•
•
QOSC36[7:6]: Priority service type for the ports select this parameter set. Option 1 to option 4
QOSC37[7]: Priority service allow flow control for the ports select this parameter set
QOSC37[6]: Flow Control pause best effort traffic only
13.6.34
•
Classes WFQ Credit Port G1
Accessed by serial interface (R/W)
W0 - QOSC40[5:0] – CREDIT_C0_G1 (CPU Address 53F)
[7:6] - Priority service type. Option 1 to 4.
W1 - QOSC41[5:0] – CREDIT_C1_G1 (CPU Address 540)
[7]: Priority service allow flow control for the ports select this parameter set.
[6]: Flow Control pause best effort traffic only
W2 - QOSC42[5:0] – CREDIT_C2_G1 (CPU Address 541)
W3 - QOSC43[5:0] – CREDIT_C3_G1 (CPU Address 542)
W4 - QOSC44[5:0] – CREDIT_C4_G1 (CPU Address 543)
W5 - QOSC45[5:0] – CREDIT_C5_G1 (CPU Address 544)
W6 - QOSC46[5:0] – CREDIT_C6_G1 (CPU Address 545)
W7 - QOSC47[5:0] – CREDIT_C7_G1 (CPU Address 546)
QOSC40 through QOSC47 represents the set of WFQ parameters for Gigabit port 24. The granularity of the
numbers is 1 and their sum must be 64. QOSC47 corresponds to W7 and QOSC40 corresponds to W0. In the 2G
trunk configuration, the sum of all values QOSC40 through QOSC47 must equal 128.
13.6.35
•
Classes WFQ Credit Port G2
Accessed by serial interface (R/W)
W0 - QOSC48[5:0] – CREDIT_C0_G2 (CPU Address 547)
[7:6] - Priority service type. Option 1 to 4.
W1 - QOSC49[5:0] – CREDIT_C1_G2 (CPU Address 548)
[7]: Priority service allow flow control for the ports select this parameter set.
[6]: Flow Control pause best effort traffic only
W2 - QOSC50[5:0] – CREDIT_C2_G2 (CPU Address 549)
W3 - QOSC51[5:0] – CREDIT_C3_G2 (CPU Address 54a)
W4 - QOSC52[5:0] – CREDIT_C4_G2 (CPU Address 54b)
W5 - QOSC53[5:0] – CREDIT_C5_G2 (CPU Address 54c)
W6 - QOSC54[5:0] – CREDIT_C6_G2 (CPU Address 54d)
W7 - QOSC55[5:0] – CREDIT_C7_G2 (CPU Address 54e)
QOSC48 through QOSC55 represents the set of WFQ parameters for Gigabit port 25. The granularity of the
numbers is 1, and their sum must be 64. QOSC55 corresponds to W7 and QOSC48 corresponds to W0. In the 2G
trunk configuration, the sum of all values QOSC48 through QOSC55 must equal 128.
60
Zarlink Semiconductor Inc.
MVTX2603
13.6.36
•
Data Sheet
Class 6 Shaper Control Port G1
Accessed by serial interface (R/W)
• QOSC56[5:0] – TOKEN_RATE_G1 (Address 54f). Programs the average rate for Gigabit port 1. When equal to 0,
shaper is disable. Granularity is 1.
• QOSC57[7:0] – TOKEN_LIMIT_G1 (Address 550). Programs the maximum counter for Gigabit port1. Granularity is
16 bytes.
Shaper is implemented to control the peak and average rate for outgoing traffic with priority 6 (queue 6). Shaper is
limited to gigabit ports and queue P6 when it is in strict priority. QOSC41 programs the peak rate for Gigabit port 1.
See Programming QoS Registers Application Note for more information.
13.6.37
•
Class 6 Shaper Control Port G2
Accessed by serial interface (R/W)
• QOSC58[5:0] – TOKEN_RATE_G2 (CPU Address 551). Programs the average rate for Gigabit port 2. When equal to
0, shaper is disable. Granularity is 1.
• QOSC59[7:0] – TOKEN_LIMIT_G2 (CPU Address 552). Programs the maximum counter for Gigabit port2.
Granularity is 16 bytes.
Shaper is implemented to control the peak and average rate for outgoing traffic with priority 6 (queue 6). Shaper is
limited to gigabit ports and queue P6 when it is in strict priority. QOSC49 programs the peak rate for Gigabit port 2.
See Programming QoS Registers Application Note for more information.
13.6.38
•
•
RDRC0 – WRED Rate Control 0
I2C Address: h0FB, CPU Address: h553
Accessed by serial Interface and IcC (R/W)
7
4
3
X Rate
0
Y Rate
Bits [7:4]:
•
Corresponds to the frame drop percentage X% for WRED. Granularity
6.25%.
Bits [3:0]:
•
Corresponds to the frame drop percentage Y% for WRED. Granularity
6.25%.
See Programming QoS Registers Application Note for more information.
13.6.39
•
•
RDRC1 – WRED Rate Control 1
I2C Address: h0FC, CPU Address: h554
Accessed by serial Interface and I2C (R/W)
7
4
3
Z Rate
0
B Rate
Bits [7:4]:
•
Corresponds to the frame drop percentage Z% for WRED. Granularity 6.25%.
Bits [3:0]:
•
Corresponds to the best effort frame drop percentage B%, when shared pool is
all in use and destination port best effort queue reaches UCC. Granularity
6.25%.
See Programming QoS Register Application Note for more information.
61
Zarlink Semiconductor Inc.
MVTX2603
13.6.40
Data Sheet
User Defined Logical Ports and Well Known Ports
The MVTX2603 supports classifying packet priority through layer 4 logical port information. It can be setup by 8
Well Known Ports, 8 User Defined Logical Ports and 1 User Defined Range. The 8 Well Known Ports supported are
•
•
•
•
•
•
•
•
0:23
1:512
2:6000
3:443
4:111
5:22555
6:22
7:554
Their respective priority can be programmed via Well_Known_Port [7:0] priority register. Well_Known_Port_ Enable
can individually turn on/off each Well Known Port if desired.
Similarly, the User Defined Logical Port provides the user programmability to the priority, plus the flexibility to select
specific logical ports to fit the applications. The 8 User Logical Ports can be programmed via User_Port 0-7
registers. Two registers are required to be programmed for the logical port number. The respective priority can be
programmed to the User_Port [7:0] priority register. The port priority can be individually enabled/disabled via
User_Port_Enable register.
The User Defined Range provides a range of logical port numbers with the same priority level. Programming is
similar to the User Defined Logical Port. Instead of programming a fixed port number, an upper and lower limit need
to be programmed, they are: {RHIGHH, RHIGHL} and {RLOWH, RLOWL} respectively. If the value in the upper limit
is smaller or equal to the lower limit, the function is disabled. Any IP packet with a logical port that is less than the
upper limit and more than the lower limit will use the priority specified in RPRIORITY.
13.6.40.1
•
•
•
•
•
•
•
•
•
USER_PORT0_(0~7) – User Define Logical Port (0~7)
USER_PORT_0 - I2C Address h0D6 + 0DE; CPU Address 580(Low) + 581(High)
USER_PORT_1 - I2C Address h0D7 + 0DF; CPU Address 582 + 583
USER_PORT_2 - I2C Address h0D8 + 0E0; CPU Address 584 + 585
USER_PORT_3 - I2C Address h0D9 + 0E1; CPU Address 586 + 587
USER_PORT_4 - I2C Address h0DA + 0E2; CPU Address 588 + 589
USER_PORT_5 - I2C Address h0DB + 0E3; CPU Address 58a + 58b
USER_PORT_6 - I2C Address h0DC + 0E4; CPU Address 58c + 58d
USER_PORT_7 - I2C Address h0DD + 0E5; CPU Address 58e + 58f
Accessed by serial interface and I2C (R/W)
7
0
TCP/UDP Logic Port Low
7
0
TCP/UDP Logic Port High
•
(Default 00) This register is duplicated eight times from PORT 0 through PORT 7 and allows the definition of
eight separate ports.
62
Zarlink Semiconductor Inc.
MVTX2603
13.6.40.2
•
•
USER_PORT_[1:0]_PRIORITY - User Define Logic Port 1 and 0 Priority
I2C Address: h0E6, CPU Address: h590
Accessed by serial interface and I2C (R/W)
7
5
4
Priority 1
•
Drop
Priority setting, transmission + dropping, for logic port 0
Bits [7:4]:
•
Priority setting, transmission + dropping, for logic port 1 (Default 00)
USER_PORT_[3:2]_PRIORITY - User Define Logic Port 3 and 2 Priority
5
4
0
Priority 2
Drop
I2C Address: h0E8, CPU Address: h592
Accessed by serial interface and I2C (R/W)
5
4
3
Drop
1
0
Priority 4
Drop
(Default 00)
13.6.40.5
USER_PORT_[7:6]_PRIORITY - User Define Logic Port 7 and 6 Priority
I2C Address: h0E9, CPU Address: h593
Accessed by serial interface and I2C (R/W)
7
5
4
Priority 7
3
Drop
1
0
Priority 6
Drop
(Default 00)
13.6.40.6
•
1
USER_PORT_[5:4]_PRIORITY - User Define Logic Port 5 and 4 Priority
Priority 5
•
•
3
Drop
7
•
Drop
I2C Address: h0E7, CPU Address: h591
Accessed by serial interface and I2C (R/W)
13.6.40.4
•
•
Priority 0
0
•
Priority 3
•
1
Bits [3:0]:
7
•
•
3
The chip allows the definition of the priority
13.6.40.3
•
•
Data Sheet
USER_PORT_ENABLE [7:0] – User Define Logic 7 to 0 Port Enables
I2C
Address: h0EA, CPU Address: h594
Accessed by serial interface and I2C (R/W)
7
6
5
4
3
2
1
0
P7
P6
P5
P4
P3
P2
P1
P0
(Default 00)
63
Zarlink Semiconductor Inc.
MVTX2603
13.6.40.7
•
•
WELL_KNOWN_PORT [1:0] PRIORITY- Well Known Logic Port 1 and 0 Priority
I2C Address: h0EB, CPU Address: h595
Accessed by serial interface and I2C (R/W)
7
5
Priority 1
•
•
•
4
Drop
5
4
Drop
1
Priority 2
0
Drop
WELL_KNOWN_PORT [5:4] PRIORITY- Well Known Logic Port 5 and 4 Priority
Address: h0ED, CPU Address: h597
Accessed by serial interface and I2C (R/W)
5
4
Priority 5
3
Drop
1
Priority 4
0
Drop
Priority 4 - Well known port 111 for sun rpe.
Priority 5 - Well known port 22555 for IP Phone call setup
(Default 00)
13.6.40.10
WELL_KNOWN_PORT [7:6] PRIORITY- Well Known Logic Port 7 and 6 Priority
I2C Address: h0EE, CPU Address: h598
Accessed by serial interface and I2C (R/W)
7
5
Priority 7
•
•
•
3
I2C
7
•
•
Drop
Priority 2 - Well known port 6000 for XWIN.
Priority 3 - Well known port 443 for http. sec
(Default 00)
13.6.40.9
•
•
•
Priority 0
0
I2C Address: h0EC, CPU Address: h596
Accessed by serial interface and I2C (R/W)
Priority 3
•
•
1
WELL_KNOWN_PORT [3:2] PRIORITY- Well Known Logic Port 3 and 2 Priority
7
•
•
•
3
Priority 0 - Well known port 23 for telnet applications
Priority 1 - Well known port 512 for TCP/UDP
(Default 00)
13.6.40.8
•
•
Data Sheet
4
3
Drop
1
Priority 6
Priority 6 - Well known port 22 for ssh.
Priority 7 - Well known port 554 for rtsp.
(Default 00)
64
Zarlink Semiconductor Inc.
0
Drop
MVTX2603
13.6.40.11
•
•
Data Sheet
WELL KNOWN_PORT_ENABLE [7:0] – Well Known Logic 7 to 0 Port Enables
I2C Address: h0EF, CPU Address: h599
Accessed by serial interface and I2C (R/W)
7
6
5
4
3
2
1
0
P7
P6
P5
P4
P3
P2
P1
P0
• 1 - Enable
• 0 - Disable
•
(Default 00)
13.6.40.12
•
•
•
I2C Address: h0F4, CPU Address: h59a
Accessed by serial interface and I2C (R/W)
(Default 00)
13.6.40.13
•
•
•
RHIGHH – User Define Range High Bit 15:8
I2C
Address: h0D4, CPU Address: h59d
Accessed by serial interface and I2C (R/W)
(Default 00)
13.6.40.16
•
•
RHIGHL – User Define Range High Bit 7:0
I2C Address: h0D3, CPU Address: h59c
Accessed by serial interface and I2C (R/W)
(Default 00)
13.6.40.15
•
•
•
RLOWH – User Define Range Low Bit 15:8
I2C Address: h0F5, CPU Address: h59b
Accessed by serial interface and I2C (R/W)
(Default 00)
13.6.40.14
•
•
•
RLOWL – User Define Range Low Bit 7:0
RPRIORITY – User Define Range Priority
I2C
Address: h0D5, CPU Address: h59e
Accessed by serial interface and I2C (R/W)
7
4
3
1
Range Transmit Priority
•
0
Drop
RLOW and RHIGH form a range for logical ports to be classified with priority specified in RPRIORITY
Bit [3:1]
•
Transmit Priority
Bits [0]:
•
Drop Priority
65
Zarlink Semiconductor Inc.
MVTX2603
13.7
13.7.1
•
•
Data Sheet
Group 6 Address MISC Group
MII_OP0 – MII Register Option 0
I2C
Address: hF0, CPU Address:h600
Accessed by serial interface and I2C (R/W)
7
6
hfc
Bits [7]:
5
1prst
•
4
0
DisJ
Vendor Spc. Reg Addr
Half duplex flow control feature
• 0 = Half duplex flow control always enable
• 1 = Half duplex flow control by negotiation
Bits [6]:
•
Link partner reset auto-negotiate disable
Bits [5]:
•
Disable jabber detection. This is for HomePNA application or any serial
operation slower than 10 Mbps.
• 1 = disable
• 0 = enable
Bit [4:0]:
13.7.2
•
•
•
Vendor specified link status register address (null value means don’t
use it) (Default 00); used when the Linkup bit position in the PHY is
non-standard.
MII_OP1 – MII Register Option 1
I2C
Address: hF1, CPU Address:h601
Accessed by serial interface and I2C (R/W)
7
4
3
0
Speed bit location
13.7.3
•
•
Duplex bit location
Bits [3:0]:
•
Duplex bit location in vendor specified register
Bits [7:4]:
•
•
Speed bit location in vendor specified register
(Default 00)
FEN – Feature Register
I2C Address: hF2, CPU Address: h602
Accessed by serial interface and I2C (R/W)
7
6
DML
MII
Bits [1:0]:
•
5
3
2
DS
Reserved (Default 0)
66
Zarlink Semiconductor Inc.
1
0
MVTX2603
Data Sheet
Bit [2]:
•
•
Support DS EF Code. (Default 0)
When 101110 is detected in DS field (TOS [7:2]), the frame priority is
set for 110 and drop is set for 0
Bit [5:3]:
•
Reserved (Default 010)
Bit [6]:
•
Disable MII Management State Machine
• 0: Enable MII Management State Machine (Default 0)
• 1: Disable MII Management State Machine
Bit [7]:
•
Disable using MCT link list structure
• 0: Enable using MCT Link List structure (Default 0)
• 1: Disable using MCT Link List structure
13.7.4
•
•
•
MIIC0 – MII Command Register 0
CPU Address: h603
Accessed by serial interface only (R/W)
Bit [7:0] MII Data [7:0]
Note: Before programming MII command: set FEN[6], check MIIC3, making sure no RDY and no VALID; then
program MII command.
13.7.5
•
•
•
MIIC1 – MII Command Register 1
CPU Address: h604
Accessed by serial interface only (R/W)
Bit [7:0] MII Data [15:8]
Note: Before programming MII command: set FEN[6], check MIIC3, making sure no RDY and no VALID; then
program MII command.
13.7.6
•
•
MIIC2 – MII Command Register 2
CPU Address :h605
Accessed by serial interface only (R/W)
7
6
5
4
0
Mii OP
Register address
Bits [4:0]:
•
REG_AD – Register PHY Address
Bit [6:5]
•
OP – Operation code “10” for read command and “01” for write
command
Note: Before programming MII command: set FEN[6], check MIIC3, making sure no RDY and no VALID; then
program MII command. Writing to this register will initiate a serial management cycle to the MII management
interface. For detail information, please refer to the PHY Control Application Note.
67
Zarlink Semiconductor Inc.
MVTX2603
13.7.7
•
•
Data Sheet
MIIC3 – MII Command Register 3
CPU Address: h606
Accessed by serial interface only (R/W)
7
6
Rdy
5
4
0
Valid
PHY address
Bits [4:0]:
•
PHY_AD – 5 Bit PHY Address
Bit [6]
•
VALID – Data Valid from PHY (Read Only)
Bit [7]
•
RDY – Data is returned from PHY (Ready Only)
Note: Before programming MII command: set FEN[6], check MIIC3, making sure no RDY and no VALID; then
program MII command.
13.7.8
•
•
•
CPU Address: h607
Accessed by serial interface only (RO)
Bit [7:0] MII Data [7:0]
13.7.9
•
•
•
MIID1 – MII Data Register 1
CPU Address: h608
Accessed by serial interface only (RO)
Bit [7:0] MII Data [15:8]
13.7.10
•
•
MIID0 – MII Data Register 0
LED Mode – LED Control
CPU Address: h609
Accessed by serial interface and I2C (R/W)
7
5
4
3
2
Clock rate
1
0
Hold Time
Bit [0]
•
Reserved (Default 0)
Bit [2:1]:
•
Hold time for LED signal (Default= 00)
• 00 = 8 msec 01 = 16 msec
10 = 32 msec 11 = 64 msec
Bit [4:3]:
•
LED clock frequency (Default 0)
For 100MHz SCLK
00 = 100 M/8 = 12.5 MHz
10 = 100 M/32 = 3.125 MHz
01 = 100 M/16 = 6.25 MHz
11 = 100 M/64 = 1.5625 MHz
For 125 MHz SCLK
Bit [7:6]:
•
00 = 125 M/64 = 1953 KHz
01 = 125 M/128 = 977 KHz
10 = 125M/512=244 KHz
11 = 125 M/1024 = 122 KHz
Reserved. Must be 0. (Default 0)
68
Zarlink Semiconductor Inc.
MVTX2603
13.7.11
•
•
Data Sheet
CHECKSUM - EEPROM Checksum
I2C Address: FF, CPU Address: h60b
Accessed by serial interface and I2C (R/W)
Bit [7:0]:
•
(Default 0)
Before requesting that the MVTX2603 updates the EEPROM device, the correct checksum needs to be calculated
and written into this checksum register. When the MVTX2603 boots from the EEPROM the checksum is calculated
and the value must be zero. If the checksum is not zeroed the MVTX2603 does not start and pin CHECKSUM_OK
is set to zero.
The checksum formula is:FF
Σ I2C register = 0
I=0
13.8
13.8.1
•
•
Group 7 Address Port Mirroring Group
MIRROR1_SRC – Port Mirror source port
CPU Address: h700
Accessed by serial interface (R/W) (Default 7F)
7
6
5
4
0
I/O
13.8.2
•
•
Src Port Select
Bit [4:0]:
•
Source port to be mirrored. Use illegal port number to disable mirroring
Bit [5]:
•
•
1 – select ingress data
0 – select egress data
Bit [7]:
•
Must be ‘1’
MIRROR1_DEST – Port Mirror destination
CPU Address: h701
Accessed by serial interface (R/W) (Default 17)
7
5
4
0
Dest Port Select
Bit [4:0]:
•
Port Mirror Destination
69
Zarlink Semiconductor Inc.
MVTX2603
13.8.3
•
•
MIRROR2_SRC – Port Mirror source port
CPU Address: h702
Accessed by serial interface (R/W) (Default FF)
7
6
5
4
0
I/O
13.8.4
•
•
Data Sheet
Src Port Select
Bit [4:0]:
•
Source port to be mirrored. Use illegal port number to disable mirroring
Bit [5]:
•
•
1 – select ingress data
0 – select egress data
Bit [7]
•
Must be 1
MIRROR2_DEST – Port Mirror destination
CPU Address: h703
Accessed by serial interface (R/W) (Default 00)
7
5
4
0
Dest Port Select
Bit [4:0]:
13.9
13.9.1
•
•
•
Port Mirror Destination
Group F Address CPU Access Group
GCR-Global Control Register
CPU Address: hF00
Accessed by serial interface. (R/W)
7
4
3
2
1
0
Reset
Bist
SR
SC
Bit [0]:
•
•
Store configuration (Default = 0)
Write ‘1’ followed by ‘0’ to store configuration into external EEPROM
Bit [1]:
•
•
Store configuration and reset (Default = 0)
Write ‘1’ to store configuration into external EEPROM and reset chip
Bit [2]:
•
•
Start BIST (Default = 0)
Write ‘1’ followed by ‘0’ to start the device’s built-in self-test. The result
is found in the DCR register.
Bit [3]:
•
•
Soft Reset (Default = 0)
Write ‘1’ to reset chip
Bit [7:4]:
•
Reserved.
70
Zarlink Semiconductor Inc.
MVTX2603
13.9.2
•
•
DCR-Device Status and Signature Register
CPU Address: hF01
Accessed by serial interface. (RO)
7
6
5
Revision
13.9.3
•
•
Data Sheet
4
Signature
3
2
1
0
RE
BinP
BR
BW
Bit [0]:
•
•
1: Busy writing configuration to I2C
0: Not busy writing configuration to I2C
Bit [1]:
•
•
1: Busy reading configuration from I2C
0: Not busy reading configuration from I2C
Bit [2]:
•
•
1: BIST in progress
0: BIST not running
Bit [3]:
•
•
1: RAM Error
0: RAM OK
Bit [5:4]:
•
•
Device Signature
01: MVTX2603 device
Bit [7:6]:
•
•
•
Revision
00: Initial Silicon
01: XA1 Silicon
DCR1-Giga port status
CPU Address: hF02
Accessed by serial interface (RO)
7
6
4
3
2
CIC
GIGA1
Bit [1:0]:
•
•
•
•
•
Giga port 0 strap option
00 – 100 Mb MII mode
01 – 2 G mode
10 – GMII
11 – PCS
Bit [3:2]
•
•
•
•
•
Giga port 1 strap option
00 – 100 Mb MII mode
01 – 2 G mode
10 – GMII
11 – PCS
Bit [7]
•
Chip initialization completed
71
Zarlink Semiconductor Inc.
1
0
GIGA0
MVTX2603
13.9.4
•
•
DPST – Device Port Status Register
CPU Address: hF03
Accessed by serial interface (R/W)
Bit[4:0]:
•
Read back index register. This is used for selecting what to read back from
DTST. (Default 00)
-
13.9.5
•
•
•
5’b00000 - Port 0 Operating mode and Negotiation status
5’b00001 - Port 1 Operating mode/Neg status
5’b00010 - Port 2 Operating mode/Neg status
5’b00011 - Port 3 Operating mode/Neg status
5’b00100 - Port 4 Operating mode/Neg status
5’b00101 - Port 5 Operating mode/Neg status
5’b00110 - Port 6 Operating mode/Neg status
5’b00111 - Port 7 Operating mode/Neg status
5’b01000 - Port 8 Operating mode/Neg status
5’b01001 - Port 9 Operating mode/Neg status
5’b01010 - Port 10 Operating mode/Neg status
5’b01011 - Port 11 Operating mode/Neg status
5’b01100 - Port 12 Operating mode/Neg status
5’b01101 - Port 13 Operating mode/Neg status
5’b01110 - Port 14 Operating mode/Neg status
5’b01111 - Port 15 Operating mode/Neg status
5’b10000 - Port 16 Operating mode/Neg status
5’b10001 - Port 17 Operating mode/Neg status
5’b10010 - Port 18 Operating mode/Neg status
5’b00011 - Port 19 Operating mode/Neg status
5’b10100 - Port 20 Operating mode/Neg status
5’b10101 - Port 21 Operating mode/Neg status
5’b10110 - Port 22 Operating mode/Neg status
5’b10111 - Port 23 Operating mode/Neg status
5’b11000 - Reserved
5’b11001 - Port 25 Operating mode/Neg status (Gigabit port 1)
5’b11010 - Port 26 Operating mode/Neg status (Gigabit port 2)
DTST – Data read back register
CPU Address: hF04
Accessed by serial interface (RO)
This register provides various internal information as selected in DPST bit [4:0]. Refer to the PHY Control
Application Note.
7
6
5
4
3
2
1
0
MD
Info
Sig
Giga
Inkdn
FE
Fdpx
FcEn
When bit is 1
•
•
•
•
•
Data Sheet
Bit
Bit
Bit
Bit
Bit
[0]
[1]
[2]
[3]
[4]
–
–
–
–
–
Flow control enable
Full duplex port
Fast Ethernet port (if not gigabit port)
Link is down
Giga port
72
Zarlink Semiconductor Inc.
MVTX2603
•
•
•
Bit [5] – Signal detect (when PCS interface mode)
Bit [6] – 2 G signal detect (2 G mode only)
Bit [7] – Module detected (for hot swap purpose)
13.9.6
•
•
Data Sheet
PLLCR - PLL Control Register
CPU Address: hF05
Accessed by serial interface (RW)
Bit [3]
Must be '1'
Bit [7]
Selects strap option or LCLK/OECLK registers
0 - Strap option (default)
1 - LCLK/OECLK registers
13.9.7
•
•
LCLK - LA_CLK delay from internal OE_CLK
CPU Address: hF06
Accessed by serial interface (RW)
PD[12:10]
LCLK
Delay
000b
80h
8 Buffers Delay
001b
40h
7 Buffers Delay
010b
20h
6 Buffers Delay
011b
10h
5 Buffers Delay (Recommend)
100b
08h
4 Buffers Delay
101b
04h
3 Buffers Delay
110b
02h
2 Buffers Delay
111b
01h
1 Buffers Delay
The LCLK delay from SCLK is the sum of the delay programmed in here and the delay in OECLK register.
13.9.8
•
•
OECLK - Internal OE_CLK delay from SCLK
CPU Address: hF07
Accessed by serial interface (RW)
The OE_CLK is used for generating the OE0 and OE1 signals.
PD[15:13]
OECLK
Delay
000b
80h
8 Buffers Delay
001b
40h
7 Buffers Delay (Recommend)
010b
20h
6 Buffers Delay
011b
10h
5 Buffers Delay
100b
08h
4 Buffers Delay
73
Zarlink Semiconductor Inc.
MVTX2603
101b
04h
3 Buffers Delay
110b
02h
2 Buffers Delay
111b
01h
1 Buffers Delay
13.9.9
•
•
•
Data Sheet
DA – DA Register
CPU Address: hFFF
Accessed by CPU and serial interface (RO)
Always return 8’h DA. Indicate the serial port connection is good.
13.10
TBI Registers
Two sets of TBI registers are used for configure the two Gigabit ports if they are operating in TBI mode. These TBI
registers are located inside the switching chip and they are accessed through the MII command and MII data
registers.
13.10.1
•
•
Control Register
MII Address: h00
Read/Write
Bit [15]
Reset PCS logic and all TBI registers
1 = Reset
0 = Normal operation
Bit [14]
Reserved. Must be programmed with “0”.
Bit [13]
Speed selection (See bit 6 for complete details)
Bit [12]
•
•
•
Auto Negotiation Enable
1 = Enable auto-negotiation process
0 = Disable auto-negotiation process (Default)
Bit [11:10]
•
Reserved. Must be programmed with “0”
Bit [9]
•
•
•
Restart Auto Negotiation
1 = Restart auto-negotiation process
0 = Normal operation (Default)
Bit [8:7]
•
Reserved
Bit [6]
•
Speed Selection
-
Bit [5:0]
•
Bit [6][13]
1 1 = Reserved
0 =1000 Mb/s (Default)
1 = 100 Mb/s
0 0 = 10 Mb/s
Reserved. Must be programmed with “0”.
74
Zarlink Semiconductor Inc.
MVTX2603
13.10.2
•
•
MII Address: h01
Read Only
13.10.3
•
•
Status Register
Bit [15:9]
Reserved. Always read back as “0”.
Bit [8]
Reserved. Always read back as “1”.
Bit [7:6]
Reserved. Always read back as “0”.
Bit [5]
•
•
•
Auto-Negotiation Complete
1 = Auto-negotiation process completed
0 = Auto-negotiation process not completed
Bit [4]
•
Reserved. Always read back as “0”
Bit [3]
•
Reserved. Always read back as “1”
Bit [2]
•
•
•
Link Status
1 = Link is up.
0 = Link is down.
Bit [1]
•
Reserved. Always read back as “0”.
Bit [0]
•
Reserved. Always read back as “1”
Advertisement Register
MII Address: h04
Read/Write
Bit [15]
Next Page
1 = Has next page capabilities.
0 = Do not has next page capabilities (Default)
Bit [14]
Reserved. Always read back as “0”. Read Only
Bit [13:12]
Remote Fault. Default is “0”.
Bit [11:9]
•
Reserved. Always read back as “0”. Read Only.
Bit [8:7]
•
Pause. Default is “00”
Bit [6]
•
•
•
Half Duplex
1 = Support half duplex (Default)
0 = Do not support half duplex
Bit [5]
•
•
•
Full duplex
1 = Support full duplex (Default)
0 = Do not support full duplex
Bit [4:0]
•
Reserved. Always read back as “0”. Read Only.
75
Zarlink Semiconductor Inc.
Data Sheet
MVTX2603
13.10.4
•
•
MII Address: h05
Read Only
13.10.5
•
•
Bit [15]
Next Page
1 = Has next page capabilities
0 = Do not has next page capabilities
Bit [14]
Acknowledge
Bit [13:12]
Remote Fault.
Bit [11:9]
•
Reserved. Always read back as “0”
Bit [8:7]
•
Pause
Bit [6]
•
•
•
Half Duplex
1 = Support half duplex
0 = Do not support half duplex
Bit [5]
•
•
•
Full duplex
1 = Support full duplex
0 = Do not support full duplex
Bit [4:0]
•
Reserved. Always read back as “0”
Expansion Register
MII Address: h06
Read Only
13.10.6
•
•
Link Partner Ability Register
Bit [15:2]
•
Reserved. Always read back as “0”
Bit [1]
•
•
•
Page Received
1 = A new page has been received
0 = A new page has not been received
Bit [0]
•
Reserved. Always read back as “0”
Extended Status Register
MII Address: h15
Read Only
Bit [15]
•
•
•
1000 Full Duplex
1 = Support 1000 full duplex operation (Default)
0 = Do not support 1000 full duplex operation
Bit [14]
•
•
•
1000 Half Duplex
1 = Support 1000 half duplex operation (Default)
0 = Do not support 1000 half duplex operation
Bit [13:0]
•
Reserved. Always read back as “0”
76
Zarlink Semiconductor Inc.
Data Sheet
MVTX2603
14.0
BGA and Ball Signal Descriptions
14.1
BGA Views (Top-View)
14.1.1
1
2
Data Sheet
Encapsulated View
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
A
LA_D LA_D LA_D LA_D LA_D LA_A LA_O LA_A LA_A LA_A LA_A LA_D LA_D LA_D LA_D LA_D OE_C LA_C TRUN MIRR MIRR
SCL
4
7
10
13
15
4
E0_
8
13
16
19
33
36
39
42
45
LK0 LK0
K1
OR4 OR1
B
LA_D LA_D LA_D LA_D LA_D LA_D LA_A LA_O LA_A LA_A LA_A LA_A LA_D LA_D LA_D LA_D LA_D OE_C LA_C LA_D MIRR MIRR TRUN RESE
1
3
6
9
12
14 DSC_ E1_
7
12
15
18
32
35
38
41
44
LK1 LK1
62
OR5 OR2
K2 RVED
SDA
26
27
28
29
ST RO TSTO
BE
UT7
D0
TSTO TSTO
UT8 UT3
C LA_C LA_D LA_D LA_D LA_D LA_D LA_A LA_O LA_W T_MO LA_A LA_A LA_A LA_A LA_D LA_D LA_D LA_D OE_C LA_C P_D TRUN MIRR MIRR AUTO TSTO TSTO TSTO TSTO
LK
0
2
5
8
11
3
E_
E_
DE1
11
14
17
20
34
37
40
43
LK2 LK2
K0
OR3 OR0
FD UT11 UT9 UT4 UT0
D
AGN LA_D LA_D LA_D LA_D LA_D LA_D LA_D LA_D LA_A LA_A LA_W LA_D LA_D LA_D LA_D LA_D LA_D LA_D LA_D LA_D SCAN SCAN TSTO TSTO TSTO TSTO TSTO TSTO
17
19
21
23
25
27
29
31
6
10
E0_
49
51
53
55
57
59
61
63
47
COL CLK UT14 UT 13 UT12 UT10 UT5 UT1
D
SCAN
SCAN TSTO M26_ M26_
OD
L I N K UT 15 C RS T XE R ME
M26_
M26_
M26_
TXCL
MTX
TXEN CLK
K
M26_ M26_ M26_
TXD1 T XD1 RXD1
4
5
5
M26_ M26_ M26_
TXD1 T XD1 RXD1
2
3
2
M26_ M26_
TXD1 T XD1 M26_
RXD9
0
1
LA_D LA_D LA_D LA_D LA_D LA_D LA_D LA_D LA_A LA_A LA_W LA_D LA_D LA_D LA_D LA_D LA_D LA_D RESE LA_D
E SCLK 16
18
20
22
24
26
28
30
5
9
E1_
48
50
52
54
56
58
60 RVED 46
F
AVC
C
RESI SCAN LB_D LB_ D
N_
EN
63
62
G
RESE
LB_D LB_D LB_ D
LB_C
T OUT
47
61
60
LK
_
H
LB_D LB_ D LB_D LB_D LB_ D
46
45
44
59
58
VCC
VCC
VCC
VCC
VCC
J LB_D LB_ D LB_D LB_D LB_ D
43
42
41
57
56
_D LB_ D LB_D LB_D LB_ D
K LB
40
39
38
55
54
VDD VDD
TSTO TSTO
UT6 UT2
M26_ M26_
RXD RXCL
V
K
M26_ M26_
RXER COL
M26_
RXD1
3
M26_
RXD1
0
M26_
RXD1
4
M26_
RXD1
1
M26_ M26_ M26_ M26_ M26_
TXD9 TXD8 RXD6 RXD7 RXD8
VDD VDD
L LB_D LB_ D LB_D LB_D LB_ D
37
36
35
53
52
M26_ M26_ M26_ M26_ M26_
TXD4 TXD6 RXD3 RXD4 RXD5
LB_D LB_ D LB_D LB_D LB_ D
34
33
32
51
50
M26_ M26_ M26_ M26_ M26_
TXD7 TXD5 RXD0 RXD1 RXD2
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
LB_A LB_A LB_A LB_W LB_ VCC
15
16
17
E0_ WE1_
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VCC M26_ M26_
TXD0 TXD1
R LB_A LB_A LB_A LB_A LB_A VCC
10
11
12
13
14
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VCC
M25_ M25_ M25_ M25_ M25_
VCC TXCL TXEN MTX RXD RXCL
K
CLK
V
K
M
LB_A LB_A LB_A LB_D LB_D VCC
N
18
19
20
49
48
P
T LB_A LB_A LB_A LB_A LB_A VCC
5
6
7
8
9
LB_O LB_O T_MO LB_D LB_D VCC
U E0_
E1_ DE0
31
30
V
LB_A LB_ O LB_W LB_D LB_ D
DSC_ E_
E_
29
28
W
LB_D LB_ A LB_A LB_D LB_ D
15
3
4
27
26
Y
LB_D LB_ D LB_D LB_D LB_ D
14
13
12
25
24
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD VDD
GREF
_CLK
1
GREF
MDIO _CLK
0
VCC M26_ M26_
TXD2 TXD3
M25_ M25_
CRS TXER
M25_
VCC TXD1
4
M25_
TXD1
2
M25_
TXD1
0
M25_
T XD1
5
M25_
T XD1
3
M25_
T XD1
1
MDC
M25_
RXD1
5
M25_
RXD1
2
M_CL
K
M25_ M25_
RXER COL
M25_
RXD1
3
M25_
M25_
RXD1
RXD9
0
M25_
RXD1
4
M25_
RXD1
1
M25_ M25_ M25_ M25_ M25_
RXD6 TXD8 TXD9 RXD7 RXD8
VDD VDD
A LB_D LB_ D LB_D LB_D LB_ D
11
10
9
23
22
A
M25_ M25_ M25_ M25_ M25_
TXD6 TXD7 RXD3 RXD4 RXD5
A LB_D LB_ D LB_D LB_D LB_ D
8
7
6
21
20
B
M25_ M25_ M25_ M25_ M25_
TXD4 TXD5 RXD0 RXD1 RXD2
A LB_D LB_ D LB_D LB_D LB_ D
5
4
3
19
18
C
M25_ M25_ M23_ M23_ M23_
TXD2 TXD3 CRS RXD0 RXD1
A LB_D LB_ D LB_D LB_D LB_ D
2
1
0
17
16
D
VCC
VCC
VCC
VCC
M25_ M25_ M23_ M23_ M23_
TXD0 TXD1 TXD1 TXD0 TXEN
VCC
A M0_T M0_T M0_T M3_T M3_T M3_R M5_T M5_T M5_R M8_T M8_T M8_R M10_ M10_ M10_ M13_ M16_ M15_ M16_ M15_ M15_ M18_ M18_ M18_ M20_ M20_ M20_ M22_
E XEN XD0 XD1 XD1 XEN XD0 XD1 XEN XD0 XD1 XEN XD0 TXD1 TXEN RXD0 TXD1 TXD0 T XD1 RXD1 TXEN RXD0 TXD1 TXEN RXD0 TXD1 TXEN RXD0 RXD1
AF
M0_R M0_R M0_C M3_T M3_C M3_R M5_T M5_C M5_R M8_T M8_C M8_R M10_ M10_ M10_ M13_ M13_ M13_ M14_ M16R M15_ M17_ M17_ M18_ M20_ M20_ M20_ M22_ M22_
XD1 XD0
RS
XD0
RS
XD1 XD0
RS
XD1 XD0
RS
XD1 TXD0 CRS RXD1 TXD0 CRS RXD1 CRS XD0 RXD1 RXD0 CRS RXD1 TXD0 CRS RXD1 RXD0 CRS
A M1_T M1_T M1_T M2_T M2_C M4_T M4_C M6_T M6_C M7_T M7_C M9_T M9_C M11_ M11_ M12_ M12_ M14_ M15_ M16_ M16_ M18_ M18_ M19_ M19_ M21_ M21_ M22_ M22_
RS
XD1
RS
XD1
RS
XD1
RS
XD1
RS TXD1 CRS TXD1 CRS T XD1 TXD0 TXD1 CRS TXD0 CRS TXD1 CRS TXD1 CRS TXEN TXD0
G XEN XD0 XD1 XD1
M1_R M1_C M2_T M2_R M4_T M4_R M6_T M6_R M7_T M7_R M9_T M9_R M11_ M11_ M12_ M12_ M14_ M14_ M13_ M15_ M17_ M17_ M19_ M19_ M21_ M21_ M22_
XD0
RS
XD0 XD0 XD0 XD0 XD0 XD0 XD0 XD0 XD0 XD0 TXD0 RXD0 TXD0 RXD0 T XD0 RXD0 RXD0 CRS TXD0 RXD1 TXD0 RXD0 TXD0 RXD0 TXD1
A
H
M1_R M2_T M2_R M4_T M4_R M6_T M6_R M7_T M7_R M9_T M9_R M11_ M11_ M12_ M12_ M14_ M14_ M16_ M13_ M17_ M17_ M19_ M19_ M21_ M21_
XD1 XEN XD1 XEN XD1 XEN XD1 XEN XD1 XEN XD1 TXEN RXD1 T XEN RXD1 TXEN RXD1 TXEN TXEN TXEN TXD1 TXEN RXD1 TXEN RXD1
AJ
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
77
Zarlink Semiconductor Inc.
18
19
20
21
22
23
24
25
26
27
28
29
MVTX2603
14.2
Data Sheet
Ball – Signal Descriptions
All pins are CMOS type; all Input Pins are 5 Volt tolerance; and all Output Pins are 3.3 CMOS drive.
14.2.1
Ball Signal Descriptions
Ball Signal Descriptions Table
Ball No(s)
Symbol
I/O
Description
I2C Interface Note: Use I2C and Serial control interface to configure the system
A24
SCL
Output
I2C Data Clock
A25
SDA
I/O-TS with pull up
I2C Data I/O
A26
STROBE
Input with weak internal
pull up
Serial Strobe Pin
B26
D0
Input
Serial Data Input
C25
AUTOFD
Output with pull up
Serial Data Output (AutoFD)
D20, B21, D19, E19,D18,
E18, D17, E17, D16, E16,
D15, E15, D14, E14, D13,
E13, D21, E21, A18, B18,
C18, A17, B17, C17, A16,
B16, C16, A15, B15, C15,
A14, B14, D9, E9, D8, E8,
D7, E7, D6, E6, D5, E5, D4,
E4, D3, E3, D2, E2, A7, B7,
A6, B6, C6, A5, B5, C5, A4,
B4, C4, A3, B3, C3, B2, C2
LA_D[63:0]
I/O-TS with pull up
Frame Bank A– Data Bit [63:0]
C14, A13, B13, C13, A12,
B12, C12, A11, B11, C11,
D11, E11, A10, B10, D10,
E10, A8, C7
LA_A[20:3]
Output
Frame Bank A – Address Bit [20:3]
B8
LA_ADSC#
Output with pull up
Frame Bank
Control
C1
LA_CLK
Output
Frame Bank A Clock Input
C9
LA_WE#
Output with pull up
Frame Bank A Write Chip Select for
one layer SRAM application
D12
LA_WE0#
Output with pull up
Frame Bank A Write Chip Select for
lower layer of two layers SRAM
application
E12
LA_WE1#
Output with pull up
Frame Bank A Write Chip Select for
upper layer of two layers SRAM
application
Serial Control Interface
Frame Buffer Interface
78
Zarlink Semiconductor Inc.
A
Address
Status
MVTX2603
Data Sheet
Ball Signal Descriptions Table (continued)
Ball No(s)
Symbol
I/O
Description
C8
LA_OE#
Output with pull up
Frame Bank A Read Chip Select for
one layer SRAM application
A9
LA_OE0#
Output with pull up
Frame Bank A Read Chip Select for
lower layer of two layers SRAM
application
B9
LA_OE1#
Output with pull up
Frame Bank A Read Chip Select for
upper layer of two layers SRAM
application
F4, F5, G4, G5, H4, H5, J4,
J5, K4, K5, L4, L5, M4, M5,
N4, N5, G3, H1, H2, H3, J1,
J2, J3, K1, K2, K3, L1, L2,
L3, M1, M2, M3, U4, U5, V4,
V5, W4, W5, Y4, Y5, AA4,
AA5, AB4, AB5, AC4, AC5,
AD4, AD5, W1, Y1, Y2, Y3,
AA1, AA2, AA3, AB1, AB2,
AB3, AC1, AC2, AC3, AD1,
AD2, AD3
LB_D[63:0]
I/O-TS with pull up.
Frame Bank B– Data Bit [63:0]
N3, N2, N1, P3, P2, P1, R5,
R4, R3, R2, R1, T5, T4, T3,
T2, T1, W3, W2
LB_A[20:3]
Output
Frame Bank B – Address Bit [20:3]
V1
LB_ADSC#
Output with pull up
Frame Bank
Control
G1
LB_CLK
Output
Frame Bank B Clock Input
V3
LB_WE#
Output with pull up
Frame Bank B Write Chip Select for
one layer SRAM application
P4
LB_WE0#
Output with pull up
Frame Bank B Write Chip Select for
lower layer of two layers SRAM
application
P5
LB_WE1#
Output with pull up
Frame Bank B Write Chip Select for
upper layer of two layers SRAM
application
V2
LB_OE#
Output with pull up
Frame Bank B Read Chip Select for
one layer SRAM application
U1
LB_OE0#
Output with pull up
Frame Bank B Write Chip Select for
lower layer of two layers SRAM
application
U2
LB_OE1#
Output with pull up
Frame Bank B Write Chip Select for
upper layer of two layers SRAM
application
Output
MII Management Data Clock
(Common for all MII Ports [23:0])
B
Address
Status
Fast Ethernet Access Ports [23:0] RMII
R28
M_MDC
79
Zarlink Semiconductor Inc.
–
MVTX2603
Data Sheet
Ball Signal Descriptions Table (continued)
Ball No(s)
Symbol
I/O
Description
P28
M_MDIO
I/O-TS with pull up
MII Management Data I/O –
(Common for all MII Ports –[23:0]))
R29
M_CLKI
Input
Reference Input Clock
AC29, AE28, AJ27, AF27,
AJ25, AF24, AH23, AE19,
AF21, AJ19, AF18, AJ17,
AJ15, AF15, AJ13, AF12,
AJ11, AJ9, AF9, AJ7, AF6,
AJ5, AJ3, AF1
M[23:0]_RXD[1]
Input with weak internal
pull up resistors.
Ports [23:0] – Receive Data Bit [1]
AC28, AF28, AH27, AE27,
AH25, AE24, AF22, AF20,
AE21, AH19, AH20, AH17,
AH15, AE15, AH13, AE12,
AH11, AH9, AE9, AH7, AE6,
AH5, AH2, AF2
M[23:0]_RXD[0]
Input with weak internal
pull up resistors
Ports [23:0] – Receive Data Bit [0]
AC27, AF29, AG27, AF26,
AG25, AG23, AF23, AG21,
AH21, AF19, AF17, AG17,
AG15, AF14, AG13, AF11,
AG11, AG9, AF8, AG7, AF5,
AG5, AH3, AF3
M[23:0]_CRS_DV
Input with weak internal
pull down resistors.
Ports [23:0] – Carrier Sense and
Receive Data Valid
AD29, AG28, AJ26, AE26,
AJ24, AE23, AJ22, AJ20,
AE20, AJ18, AJ21, AJ16,
AJ14, AE14, AJ12, AE11,
AJ10, AJ8, AE8, AJ6, AE5,
AJ4, AG1, AE1
M[23:0]_TXEN
I/O- TS with pull up, slew
Ports [23:0] – Transmit Enable
AD27, AH28, AG26, AE25,
AG24, AE22, AJ23, AG20,
AE18, AG18, AE16, AG16,
AG14, AE13, AG12, AE10,
AG10, AG8, AE7, AG6, AE4,
AG4, AG3, AE3
M[23:0]_TXD[1]
Output, slew
Ports [23:0] – Transmit Data Bit [1]
AD28, AG29, AH26, AF25,
AH24, AG22, AH22, AE17,
AG19, AH18, AF16, AH16,
AH14, AF13, AH12, AF10,
AH10, AH8, AF7, AH6, AF4,
AH4, AG2, AE2
M[23:0]_TXD[0]
Output, slew
Ports [23:0] – Transmit Data Bit [0]
Output
Transmit Data Bit [15:0]
[7:0] - GMII
[9:0] - TBI
[15:0] - 2G
Strap option for RMII/GPSI
GMII/TBI Gigabit Ethernet Access Ports 0 & 1
U26, U25, V26, V25, W26,
W25, Y27, Y26, AA26, AA25,
AB26, AB25, AC26, AC25,
AD26, AD25
M25_TXD[15:0]
80
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
Ball Signal Descriptions Table (continued)
Ball No(s)
Symbol
I/O
Description
T28
M25_RX_DV
Input w/ pull down
Receive Data Valid
U28
M25_RX_ER
Input w/ pull up
Receive Error
R25
M25_CRS
Input w/ pull down
Carrier Sense
U29
M25_COL
Input w/ pull up
Collision Detected
T29
M25_RXCLK
Input w/ pull up
Receive Clock
U27, V29, V28, V27, W29,
W28, W27, Y29, Y28, Y25,
AA29, AA28, AA27, AB29,
AB28, AB27
M25_RXD[15:0]
Input w/ pull up
Receive Data Bit [15:0]
T26
M25_TX_EN
Output w/ pull up
Transmit Data Enable
R26
M25_TX_ER
Output w/ pull up
Transmit Error
T27
M25_MTXCLK
Input w/ pull down
MII Mode Transmit Clock
T25
M25_ TXCLK
Output
Gigabit Transmit Clock
P29
GREF_CLK0
Input w/ pull up
Gigabit Reference Clock
G26, G25, H26, H25, J26,
J25, K25, K26, M25, L26,
M26, L25, N26, N25, P26,
P25
M26_TXD[15:0]
Output
Transmit Data Bit [15:0]
F28
M26_RX_DV
Input w/ pull down
Receive Data Valid
G28
M26_RX_ER
Input w/ pull up
Receive Error
E25
M26_CRS
Input w/ pull down
Carrier Sense
G29
M26_COL
Input w/ pull up
Collision Detected
F29
M26_RXCLK
Input w/ pull up
Receive Clock
G27,H29, H28, H27, J29,
J28, J27, K29, K28, K27,
L29, L28, L27, M29, M28,
M27
M26_RXD[15:0]
Input w/ pull up
Receive Data Bit [15:0]
F26
M26_TX_EN
Output w/ pull up
Transmit Data Enable
E26
M26_TX_ER
Output w/ pull up
Transmit Error
F27
M26_MTXCLK
Input w/ pull down
MII Mode Transmit Clock
F25
M26_ TXCLK
Output
Gigabit Transmit Clock
N29
GREF_CLK1
Input w/ pull up
Gigabit Reference Clock
[7:0] - GMII
[9:0] - TBI
[15:0] - 2G
[7:0] - GMII
[9:0] - TBI
[15:0] - 2 G
[7:0] - GMII
[9:0] - TBI
[15:0] - 2 G
81
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
Ball Signal Descriptions Table (continued)
Ball No(s)
Symbol
I/O
Description
LED Interface
C29
LED_CLK/TSTOUT0
I/O- TS with pull up
LED Serial Interface Output Clock
D29
LED_SYN/TSTOUT1
I/O- TS with pull up
LED Output Data Stream Envelope
E29
LED_BIT/TSTOUT2
I/O- TS with pull up
LED Serial Data Output Stream
B28
G1_RXTX#/TSTOUT
3
I/O- TS with pull up
LED for Gigabit port 1 (receive +
transmit)
C28
G1_DPCOL#/TSTOU
T4
I/O- TS with pull up
LED for Gigabit port 1 (full duplex +
collision)
D28
G1_LINK#/TSTOUT5
I/O- TS with pull up
LED for Gigabit port 1
E28
G2_RXTX#/TSTOUT
6
I/O- TS with pull up
LED for Gigabit port 2 (receive +
transmit)
A27
G2_DPCOL#/TSTOU
T7
I/O- TS with pull up
LED for Gigabit port 2 (full duplex +
collision)
B27
G2_LINK#/TSTOUT8
I/O- TS with pull up
LED for Gigabit port 2
C27
INIT_DONE/TSTOUT
9
I/O- TS with pull up
System start operation
D27
INIT_START/TSTOU
T10
I/O- TS with pull up
Start initialization
C26
CHECKSUM_OK/TS
TOUT11
I/O- TS with pull up
EEPROM read OK
D26
FCB_ERR/TSTOUT1
2
I/O- TS with pull up
FCB memory self test fail
D25
MCT_ERR/TSTOUT1
3
I/O- TS with pull up
MCT memory self test fail
D24
BIST_IN_PRC/TSTO
UT14
I/O- TS with pull up
Processing memory self test
E24
BIST_DONE/TSTOU
T15
I/O- TS with pull up
Memory self test done
C22
TRUNK0
Input w/ weak internal pull
down resistors
Trunk Port Enable
A21
TRUNK1
Input w/ weak internal pull
down resistors
Trunk Port Enable
B24
TRUNK2
Input w/ weak internal pull
down resistors
Trunk Port Enable
Trunk Enable
Test Facility
82
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
Ball Signal Descriptions Table (continued)
Ball No(s)
Symbol
I/O
Description
U3
T_MODE0
I/O-TS
Test Pin – Set Mode upon Reset, and
provides NAND Tree test output
during test mode (Pull Up)
C10
T_MODE1
I/O-TS
Test Pin – Set Mode upon Reset, and
provides NAND Tree test output
during test mode (Pull Up)
T_MODE1
0
0
1
1
T_MODE0
0
NandTree
1
Reserved
0
Reserved
1
Regular
operation
T_MODE0 and T_MODE1 are used
for manufacturing tests. The signals
should both be set to 1 for regular
operation.
SCAN_EN
F3
Input with pull down
Scan Enable
0 - Normal mode (unconnected)
SCANMODE
E27
Input with pull down
1 - Enables Test mode.
0 - Normal mode (unconnected)
System Clock, Power, and Ground Pins
E1
SCLK
Input
System Clock at 100 MHz
K12, K13, K17,K18 M10,
N10, M20, N20, U10, V10,
U20, V20, Y12, Y13, Y17,
Y18
VDD
Power
+2.5 Volt DC Supply
F13, F14, F15, F16, F17, N6,
P6, R6, T6, U6, N24, P24,
R24, T24, U24, AD13, AD14,
AD15, AD16, AD17
VCC
Power
+3.3 Volt DC Supply
M12, M13, M14, M15,
M17, M18, N12, N13,
N15, N16, N17, N18,
P13, P14, P15, P16,
P18, R12, R13, R14,
R16, R17, R18, T12,
T14, T15, T16, T17,
U12, U13, U14, U15,
U17, U18, V12, V13,
V15, V16, V17, V18,
VSS
Power Ground
Ground
F1
AVCC
Analog Power
Analog +2.5 Volt DC Supply
D1
AGND
Analog Ground
Analog Ground
M16,
N14,
P12,
P17,
R15,
T13,
T18,
U16,
V14,
83
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
Ball Signal Descriptions Table (continued)
Ball No(s)
Symbol
I/O
Description
MISC
D22
SCANCOL
Input
Scans the Collision signal of Home
PHY
D23
SCANCLK
Input/ output
Clock for scanning
collision and link
E23
SCANLINK
Input
Link up signal from Home PHY
F2
RESIN#
Input
Reset Input
G2
RESETOUT#
Output
Reset PHY
E20, B25
Reserved
I/O-TS
Reserved Pins. Leave
unconnected.
Home
Bootstrap Pins (Default= pull up, 1= pull up 0= pull down)
After reset TSTOUT0 to TSTOUT15 are used by the LED interface.
C29
TSTOUT0
Default: Active High (1)
GIGA Link polarity
0 - Active low
1 - Active high
D29
TSTOUT1
Default: Enable (1)
RMII MAC Power Saving Enable
0 - No power saving
1 - Power saving
E29
TSTOUT2
C28, B28
TSTOUT[4:3]
C28
TSTOUT4
Default: Enable (1)
Recommend disable
(0) with pull-down
Giga Half Duplex Support
0 - Disable
1 - Enable
Reserved
Default: SBRAM (1)
Memory is SBRAM/ZBT
0 - ZBT
1 – Pipeline SBRAM
D28
TSTOUT5
Default: SCLK (1)
Scan Speed
0 - ¼ SCLK(HPNA)
1 - SCLK
E28
TSTOUT6
A27
TSTOUT7
Reserved
Default: 128 K x 32 or
128 K x 64 (1)
Memory Size
0 - 256 K x 32 or 256 K x 64
(4 M total)
1 - 128 K x 32 or 128 K x 64
(2 M total)
84
Zarlink Semiconductor Inc.
PHY
MVTX2603
Data Sheet
Ball Signal Descriptions Table (continued)
Ball No(s)
B27
Symbol
I/O
TSTOUT8
Description
Default: Not Installed (1)
EEPROM Installed
0 - EEPROM installed
1 - EEPROM not installed
C27
TSTOUT9
Default:
MCT
enable (1)
aging
MCT Aging
0 - MCT aging disable
1 - MCT aging enable
D27
TSTOUT10
Default:
FCB
enable (1)
aging
FCB Aging
0 - FCB aging disable
1 - FCB aging enable
C26
TSTOUT11
Default: Timeout
enable (1)
reset
Timeout Reset
0 - Time out reset disable
1 - Time out reset enable. Issue reset
if any state machine did not go back
to idle for 5 Sec.
D26
TSTOUT12
Default: Normal (1)
Test Speed Up
0 - Enable test speed up. Do not use.
1 - Disable test speed up
D25
TSTOUT13
Default: Single depth (1)
FDB RAM depth (1 or 2 layers)
0 - Two layers
1 - One layer
D24
TSTOUT14
E24
TSTOUT15
Reserved.
Default: Normal operation
SRAM Test Mode
0 - Enable test mode
1 - Normal operation
T26, R26
G0_TXEN, G0_TXER
Default: PCS
Giga0
Mode: G0_TXEN G0_TXER
0
0
MII
0
1
2G
1
0
GMII
1
1
PCS
F26, E26
G1_TXEN, G1_TXER
Default: PCS
Giga1
Mode: G1_TXEN G1_TXER
0
0
MII
0
1
2G
1
0
GMII
1
1
PCS
85
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
Ball Signal Descriptions Table (continued)
Ball No(s)
Symbol
I/O
Description
AD29, AG28, AJ26, AE26,
AJ24, AE23, AJ22, AJ20,
AE20, AJ18, AJ21, AJ16,
AJ14, AE14, AJ12, AE11,
AJ10, AJ8, AE8, AJ6, AE5,
AJ4, AG1, AE1,
M[23:0]_TXEN
Default: RMII
0 – GPSI
C21
P_D
Must be pulled-down
Reserved. Must be pulled-down.
C19, B19, A19
OE_CLK[2:0]
Default: 111
Programmable delay for internal
OE_CLK from SCLK input. The
OE_CLK is used for generating the
OE0 and OE1 signals
1 - RMII
Suggested value is 001.
LA_CLK[2:0]
C20, B20, A20
Default: 111
Programmable delay for LA_CLK and
LB_CLK from internal OE_CLK. The
LA_CLK and LB_CLK delay from
SCLK is the sum of the delay
programmed in here and the delay in
P_D[15:13].
Suggested value is 011.
B22, A22, C23, B23, A23,
C24
MIRROR[5:0]
Default: 111111
Dedicated Port Mirror Mode. The first
5 bits select the port to be mirrored.
The last bit selects either ingress or
egress data.
Note:
# = Active low signal
Input = Input signal
In-ST = Input signal with Schmitt-Trigger
Output = Output signal (Tri-State driver)
Out-OD = Output signal with Open-Drain driver
I/O-TS = Input & Output signal with Tri-State driver
I/O-OD = Input & Output signal with Open-Drain driver
14.3
Ball – Signal Name
Ball – Signal Name Table
Ball
No.
Signal
Name
Ball
No.
Signal Name
Signal
Name
Ball No.
D20
LA_D[63]
D3
LA_D[19]
A9
LA_OE0#
B21
LA_D[62]
E3
LA_D[18]
B9
LA_OE1#
D19
LA_D[61]
D2
LA_D[17]
F4
LB_D[63]
E19
LA_D[60]
E2
LA_D[16]
F5
LB_D[62]
D18
LA_D[59]
A7
LA_D[15]
G4
LB_D[61]
E18
LA_D[58]
B7
LA_D[14]
G5
LB_D[60]
86
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
Ball – Signal Name Table (continued)
Ball
No.
Signal
Name
Ball
No.
Signal Name
Signal
Name
Ball No.
D17
LA_D[57]
A6
LA_D[13]
H4
LB_D[59]
E17
LA_D[56]
B6
LA_D[12]
H5
LB_D[58]
D16
LA_D[55]
C6
LA_D[11]
J4
LB_D[57]
E16
LA_D[54]
A5
LA_D[10]
J5
LB_D[56]
D15
LA_D[53]
B5
LA_D[9]
K4
LB_D[55]
E15
LA_D[52]
C5
LA_D[8]
K5
LB_D[54]
D14
LA_D[51]
A4
LA_D[7]
L4
LB_D[53]
E14
LA_D[50]
B4
LA_D[6]
L5
LB_D[52]
D13
LA_D[49]
C4
LA_D[5]
M4
LB_D[51]
E13
LA_D[48]
A3
LA_D[4]
M5
LB_D[50]
D21
LA_D[47]
B3
LA_D[3]
N4
LB_D[49]
E21
LA_D[46]
C3
LA_D[2]
N5
LB_D[48]
A18
LA_D[45]
B2
LA_D[1]
G3
LB_D[47]
B18
LA_D[44]
C2
LA_D[0]
H1
LB_D[46]
C18
LA_D[43]
C14
LA_A[20]
H2
LB_D[45]
A17
LA_D[42]
A13
LA_A[19]
H3
LB_D[44]
B17
LA_D[41]
B13
LA_A[18]
J1
LB_D[43]
C17
LA_D[40]
C13
LA_A[17]
J2
LB_D[42]
A16
LA_D[39]
A12
LA_A[16]
J3
LB_D[41]
B16
LA_D[38]
B12
LA_A[15]
K1
LB_D[40]
C16
LA_D[37]
C12
LA_A[14]
K2
LB_D[39]
A15
LA_D[36]
A11
LA_A[13]
K3
LB_D[38]
B15
LA_D[35]
B11
LA_A[12]
L1
LB_D[37]
C15
LA_D[34]
C11
LA_A[11]
L2
LB_D[36]
A14
LA_D[33]
D11
LA_A[10]
L3
LB_D[35]
B14
LA_D[32]
E11
LA_A[9]
M1
LB_D[34]
D9
LA_D[31]
A10
LA_A[8]
M2
LB_D[33]
E9
LA_D[30]
B10
LA_A[7]
M3
LB_D[32]
D8
LA_D[29]
D10
LA_A[6]
U4
LB_D[31]
E8
LA_D[28]
E10
LA_A[5]
U5
LB_D[30]
87
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
Ball – Signal Name Table (continued)
Ball
No.
Signal
Name
Ball
No.
Signal Name
Signal
Name
Ball No.
D7
LA_D[27]
A8
LA_A[4]
V4
LB_D[29]
E7
LA_D[26]
C7
LA_A[3]
V5
LB_D[28]
D6
LA_D[25]
B8
LA_ADSC#
W4
LB_D[27]
E6
LA_D[24]
C1
LA_CLK
W5
LB_D[26]
D5
LA_D[23]
C9
LA_WE#
Y4
LB_D[25]
E5
LA_D[22]
D12
LA_WE0#
Y5
LB_D[24]
D4
LA_D[21]
E12
LA_WE1#
AA4
LB_D[23]
E4
LA_D[20]
C8
LA_OE#
AA5
LB_D[22]
AB4
LB_D[21]
U2
LB_OE1#
AH7
M[4]_RXD[0]
AB5
LB_D[20]
R28
MDC
AE6
M[3]_RXD[0]
AC4
LB_D[19]
P28
MDIO
AH5
M[2]_RXD[0]
AC5
LB_D[18]
R29
M_CLK
AH2
M[1]_RXD[0]
AD4
LB_D[17]
AC29
M[23]_RXD[1]
AF2
M[0]_RXD[0]
AD5
LB_D[16]
AE28
M[22]_RXD[1]
AC27
M[23]_CRS_DV
W1
LB_D[15]
AJ27
M[21]_RXD[1]
AF29
M[22]_CRS_DV
Y1
LB_D[14]
AF27
M[20]_RXD[1]
AG27
M[21]_CRS_DV
Y2
LB_D[13]
AJ25
M[19]_RXD[1]
AF26
M[20]_CRS_DV
Y3
LB_D[12]
AF24
M[18]_RXD[1]
AG25
M[19]_CRS_DV
AA1
LB_D[11]
AH23
M[17]_RXD[1]
AG23
M[18]_CRS_DV
AA2
LB_D[10]
AE19
M[16]_RXD[1]
AF23
M[17]_CRS_DV
AA3
LB_D[9]
AF21
M[15]_RXD[1]
AG21
M[16]_CRS_DV
AB1
LB_D[8]
AJ19
M[14]_RXD[1]
AH21
M[15]_CRS_DV
AB2
LB_D[7]
AF18
M[13]_RXD[1]
AF19
M[14]_CRS_DV
AB3
LB_D[6]
AJ17
M[12]_RXD[1]
AF17
M[13]_CRS_DV
AC1
LB_D[5]
AJ15
M[11]_RXD[1]
AG17
M[12]_CRS_DV
AC2
LB_D[4]
AF15
M[10]_RXD[1]
AG15
M[11]_CRS_DV
AC3
LB_D[3]
AJ13
M[9]_RXD[1]
AF14
M[10]_CRS_DV
AD1
LB_D[2]
AF12
M[8]_RXD[1]
AG13
M[9]_CRS_DV
AD2
LB_D[1]
AJ11
M[7]_RXD[1]
AF11
M[8]_CRS_DV
AD3
LB_D[0]
AJ9
M[6]_RXD[1]
AG11
M[7]_CRS_DV
88
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
Ball – Signal Name Table (continued)
Ball
No.
Signal
Name
Ball
No.
Signal Name
Signal
Name
Ball No.
N3
LB_A[20]
AF9
M[5]_RXD[1]
AG9
M[6]_CRS_DV
N2
LB_A[19]
AJ7
M[4]_RXD[1]
AF8
M[5]_CRS_DV
N1
LB_A[18]
AF6
M[3]_RXD[1]
AG7
M[4]_CRS_DV
P3
LB_A[17]
AJ5
M[2]_RXD[1]
AF5
M[3]_CRS_DV
P2
LB_A[16]
AJ3
M[1]_RXD[1]
AG5
M[2]_CRS_DV
P1
LB_A[15]
AF1
M[0]_RXD[1]
AH3
M[1]_CRS_DV
R5
LB_A[14]
AC28
M[23]_RXD[0]
AF3
M[0]_CRS_DV
R4
LB_A[13]
AF28
M[22]_RXD[0]
AD29
M[23]_TXEN
R3
LB_A[12]
AH27
M[21]_RXD[0]
AG28
M[22]_TXEN
R2
LB_A[11]
AE27
M[20]_RXD[0]
AJ26
M[21]_TXEN
R1
LB_A[10]
AH25
M[19]_RXD[0]
AE26
M[20]_TXEN
T5
LB_A[9]
AE24
M[18]_RXD[0]
AJ24
M[19]_TXEN
T4
LB_A[8]
AF22
M[17]_RXD[0]
AE23
M[18]_TXEN
T3
LB_A[7]
AF20
M[16]_RXD[0]
AJ22
M[17]_TXEN
T2
LB_A[6]
AE21
M[15]_RXD[0]
AJ20
M[16]_TXEN
T1
LB_A[5]
AH19
M[14]_RXD[0]
AE20
M[15]_TXEN
W3
LB_A[4]
AH20
M[13]_RXD[0]
AJ18
M[14]_TXEN
W2
LB_A[3]
AH17
M[12]_RXD[0]
AJ21
M[13]_TXEN
V1
LB_ADSC#
AH15
M[11]_RXD[0]
AJ16
M[12]_TXEN
G1
LB_CLK
AE15
M[10]_RXD[0]
AJ14
M[11]_TXEN
V3
LB_WE#
AH13
M[9]_RXD[0]
AE14
M[10]_TXEN
P4
LB_WE0#
AE12
M[8]_RXD[0]
AJ12
M[9]_TXEN
P5
LB_WE1#
AH11
M[7]_RXD[0]
AE11
M[8]_TXEN
V2
LB_OE#
AH9
M[6]_RXD[0]
AJ10
M[7]_TXEN
U1
LB_OE0#
AE9
M[5]_RXD[0]
AJ8
M[6]_TXEN
AE8
M[5]_TXEN
AH8
M[6]_TXD[0]
G27
M26_RXD[15]
AJ6
M[4]_TXEN
AF7
M[5]_TXD[0]
H29
M26_RXD[14]
AE5
M[3]_TXEN
AH6
M[4]_TXD[0]
H28
M26_RXD[13]
AJ4
M[2]_TXEN
AF4
M[3]_TXD[0]
H27
M26_RXD[12]
AG1
M[1]_TXEN
AH4
M[2]_TXD[0]
J29
M26_RXD[11]
89
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
Ball – Signal Name Table (continued)
Ball
No.
Signal
Name
Ball
No.
Signal Name
Signal
Name
Ball No.
AE1
M[0]_TXEN
AG2
M[1]_TXD[0]
J28
M26_RXD[10]
AD27
M[23]_TXD[1]
AE2
M[0]_TXD[0]
J27
M26_RXD[9]
AH28
M[22]_TXD[1]
U26
M25_TXD[15]
K29
M26_RXD[8]
AG26
M[21]_TXD[1]
U25
M25_TXD[14]
K28
M26_RXD[7]
AE25
M[20]_TXD[1]
V26
M25_TXD[13]
K27
M26_RXD[6]
AG24
M[19]_TXD[1]
V25
M25_TXD[12]
L29
M26_RXD[5]
AE22
M[18]_TXD[1]
W26
M25_TXD[11]
L28
M26_RXD[4]
AJ23
M[17]_TXD[1]
W25
M25_TXD[10]
L27
M26_RXD[3]
AG20
M[16]_TXD[1]
Y27
M25_TXD[9]
M29
M26_RXD[2]
AE18
M[15]_TXD[1]
Y26
M25_TXD[8]
M28
M26_RXD[1]
AG18
M[14]_TXD[1]
AA26
M25_TXD[7]
M27
M26_RXD[0]
AE16
M[13]_TXD[1]
AA25
M25_TXD[6]
G26
M26_TXD[15]
AG16
M[12]_TXD[1]
AB26
M25_TXD[5]
G25
M26_TXD[14]
AG14
M[11]_TXD[1]
AB25
M25_TXD[4]
H26
M26_TXD[13]
AE13
M[10]_TXD[1]
AC26
M25_TXD[3]
H25
M26_TXD[12]
AG12
M[9]_TXD[1]
AC25
M25_TXD[2]
J26
M26_TXD[11]
AE10
M[8]_TXD[1]
AD26
M25_TXD[1]
J25
M26_TXD[10]
AG10
M[7]_TXD[1]
AD25
M25_TXD[0]
K25
M26_TXD[9]
AG8
M[6]_TXD[1]
U27
M25_RXD[15]
K26
M26_TXD[8]
AE7
M[5]_TXD[1]
V29
M25_RXD[14]
M25
M26_TXD[7]
AG6
M[4]_TXD[1]
V28
M25_RXD[13]
L26
M26_TXD[6]
AE4
M[3]_TXD[1]
V27
M25_RXD[12]
M26
M26_TXD[5]
AG4
M[2]_TXD[1]
W29
M25_RXD[11]
L25
M26_TXD[4]
AG3
M[1]_TXD[1]
W28
M25_RXD[10]
N26
M26_TXD[3]
AE3
M[0]_TXD[1]
W27
M25_RXD[9]
N25
M26_TXD[2]
AD28
M[23]_TXD[0]
Y29
M25_RXD[8]
P26
M26_TXD[1]
AG29
M[22]_TXD[0]
Y28
M25_RXD[7]
P25
M26_TXD[0]
AH26
M[21]_TXD[0]
Y25
M25_RXD[6]
F28
M26_RX_DV
AF25
M[20]_TXD[0]
AA29
M25_RXD[5]
G28
M26_RX_ER
AH24
M[19]_TXD[0]
AA28
M25_RXD[4]
E25
M26_CRS
90
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
Ball – Signal Name Table (continued)
Ball
No.
Signal
Name
Ball
No.
Signal Name
Signal
Name
Ball No.
AG22
M[18]_TXD[0]
AA27
M25_RXD[3]
G29
M26_COL
AH22
M[17]_TXD[0]
AB29
M25_RXD[2]
F29
M26_RXCLK
AE17
M[16]_TXD[0]
AB28
M25_RXD[1]
F26
M26_TX_EN
AG19
M[15]_TXD[0]
AB27
M25_RXD[0]
E26
M26_TX_ER
AH18
M[14]_TXD[0]
R26
M25_TX_ER
F25
M26_TXCLK
AF16
M[13]_TXD[0]
T25
M25_TXCLK
E24
BIST_DONE/TSTOUT[15]
AH16
M[12]_TXD[0]
T26
M25_TX_EN
D24
BIST_IN_PRC/TST0UT[14]
AH14
M[11]_TXD[0]
T28
M25_RX_DV
D25
MCT_ERR/TSTOUT[13]
AF13
M[10]_TXD[0]
U28
M25_RX_ER
D26
FCB_ERR/TSTOUT[12]
AH12
M[9]_TXD[0]
R25
M25_CRS
C26
CHECKSUM_OK/TSTOUT[11]
AF10
M[8]_TXD[0]
U29
M25_COL
D27
INIT_START/TSTOUT[10]
AH10
M[7]_TXD[0]
T29
M25_RXCLK
C27
INIT_DONE/TSTOUT[9]
B27
G2_LINK#/TSTOUT[8]
U18
VSS
N12
VSS
A27
G2_DPCOL#/TSTOUT[7]
V12
VSS
N13
VSS
E28
G2_RXTX#/TSTOUT[6]
V13
VSS
K17
VDD
D28
G1_LINK#/TSTOUT[5]
V14
VSS
K18
VDD
C28
G1_DPCOL#/TSTOUT[4]
V15
VSS
M10
VDD
B28
G1_RXTX#/TSTOUT[3]
V16
VSS
N10
VDD
E29
LED_BIT/TSTOUT[2]
V17
VSS
M20
VDD
D29
LED_SYN/TSTOUT[1]
V18
VSS
N20
VDD
C29
LED_CLK/TSTOUT[0]
N14
VSS
U10
VDD
N29
GREF_CLK1
N15
VSS
V10
VDD
P29
GREF_CLK0
N16
VSS
U20
VDD
F3
SCAN_EN
N17
VSS
V20
VDD
E1
SCLK
N18
VSS
Y12
VDD
U3
T_MODE0
P12
VSS
Y13
VDD
C10
T_MODE1
P13
VSS
Y17
VDD
B24
TRUNK2
P14
VSS
Y18
VDD
A21
TRUNK1
P15
VSS
K12
VDD
C22
TRUNK0
P16
VSS
K13
VDD
91
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
Ball – Signal Name Table (continued)
Ball
No.
Signal
Name
Ball
No.
Signal Name
Signal
Name
Ball No.
A26
STROBE
C19
OE_CLK2
M16
VSS
B26
D0
B19
OE_CLK1
M17
VSS
C25
AUTOFD
A19
OE_CLK0
M18
VSS
A24
SCL
R13
VSS
F16
VCC
A25
SDA
R14
VSS
F17
VCC
F1
AVCC
R15
VSS
N6
VCC
D1
AGND
R16
VSS
P6
VCC
D22
SCANCOL
R17
VSS
R6
VCC
E23
SCANLINK
R18
VSS
T6
VCC
E27
SCANMODE
T12
VSS
U6
VCC
N28
T13
VSS
N24
VCC
N27
T14
VSS
P24
VCC
F2
RESIN#
T15
VSS
R24
VCC
G2
RESETOUT#
T16
VSS
T24
VCC
B22
MIRROR5
T17
VSS
U24
VCC
A22
MIRROR4
T18
VSS
AD13
VCC
C23
MIRROR3
U12
VSS
AD14
VCC
B23
MIRROR2
U13
VSS
AD15
VCC
A23
MIRROR1
U14
VSS
AD16
VCC
C24
MIRROR0
U15
VSS
AD17
VCC
D23
SCANCLK
U16
VSS
F13
VCC
T27
M25_MTXCLK
U17
VSS
F14
VCC
F27
M26_MTXCLK
M12
VSS
F15
VCC
C20
LA_CLK2
M13
VSS
R12
VSS
B20
LA_CLK1
M14
VSS
B25
RESERVED
A20
LA_CLK0
M15
VSS
E20
RESERVED
C21
P_D
P17
VSS
P18
VSS
92
Zarlink Semiconductor Inc.
MVTX2603
14.4
14.4.1
Data Sheet
AC/DC Timing
Absolute Maximum Ratings
Storage Temperature
-65°C to +150°C
Operating Temperature
-40°C to +85°C
Maximum Junction Temperature
+125°C
Supply Voltage VCC with Respect to VSS
+3.0 V to +3.6 V
Supply Voltage VDD with Respect to VSS
+2.38 V to +2.75 V
Voltage on Input Pins
-0.5 V to (VCC + 0.3 V)
Caution: Stress above those listed may damage the device. Exposure to the Absolute Maximum Ratings for
extended periods may affect device reliability. Functionality at or above these limits is not implied.
14.4.2
DC Electrical Characteristics
VCC = 3.0 V to 3.6 V (3.3v +/- 10%)TAMBIENT = -40°C to +85°C
VDD = 2.5 V +10% - 5%
14.4.3
Recommended Operating Conditions
Symbol
Parameter Description
Min.
Typ.
Max.
Unit
fosc
Frequency of Operation
ICC
Supply Current – @ 100 MHz (VCC =3.3 V)
450
mA
IDD
Supply Current – @ 100 MHz (VDD =2.5 V)
1500
mA
VOH
Output High Voltage (CMOS)
VOL
Output Low Voltage (CMOS)
VIH-TTL
Input High Voltage (TTL 5 V tolerant)
VIL-TTL
100
MHz
2.4
V
0.4
V
VCC +
2.0
V
Input Low Voltage (TTL 5 V tolerant)
0.8
V
IIL
Input Leakage Current (0.1 V < VIN < VCC) (all pins
except those with internal pull-up/pull-down resistors)
10
µA
IOL
Output Leakage Current (0.1 V < VOUT < VCC)
10
µA
CIN
Input Capacitance
5
pF
COUT
Output Capacitance
5
pF
CI/O
I/O Capacitance
7
pF
θja
Thermal resistance with 0 air flow
11.2
C/W
θja
Thermal resistance with 1 m/s air flow
10.2
C/W
θja
Thermal resistance with 2 m/s air flow
8.9
C/W
θjc
Thermal resistance between junction and case
3.1
C/W
θjb
Thermal resistance between junction and board
6.6
C/W
2.0
93
Zarlink Semiconductor Inc.
MVTX2603
14.4.4
Data Sheet
Typical Reset & Bootstrap Timing Diagram
RESIN#
RESETOUT#
Tri-Stated
R1
R3
Bootstrap Pins
Outputs
Inputs
Outputs
R2
Figure 18 - Typical Reset & Bootstrap Timing Diagram
Symbol
Parameter
Min.
R1
Delay until RESETOUT# is tri-stated
R2
Bootstrap stabilization
R3
RESETOUT# assertion
1 µs
Typ.
Note:
10 ns
RESETOUT# state is then determined
by the external pull-up/down resistor
10 µs
Bootstrap pins sampled on rising
edge of RESIN#a
2 ms
Table 13 - Reset & Bootstrap Timing
a. The TSTOUT[8:0] pins will switch over to the LED interface functionality in 3 SCLK cycles after RESIN# goes high
94
Zarlink Semiconductor Inc.
MVTX2603
14.5
14.5.1
Data Sheet
Local Frame Buffer SBRAM Memory Interface
Local SBRAM Memory Interface
LA_CLK
L1
L2
LA_D[63:0]
Figure 19 - Local Memory Interface – Input Setup and Hold Timing
LA_CLK
L3-max
L3-min
LA_D[63:0]
L4-max
L4-min
LA_A[20:3]
L6-max
L6-min
LA_ADSC#
L7-max
L7-min
LA_WE[1:0]#
####
L8-max
L8-min
LA_OE[1:0]#
L9-max
L9-min
LA_WE#
L10-max
L10-min
LA_OE#
Figure 20 - Local Memory Interface - Output Valid Delay Timing
95
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
-100 MHz
Symbol
Parameter
Min. (ns)
Max. (ns)
Note
L1
LA_D[63:0] input set-up time
4
L2
LA_D[63:0] input hold time
1.5
L3
LA_D[63:0] output valid delay
1.5
7
CL = 25 pf
L4
LA_A[20:3] output valid delay
2
7
CL = 30 pf
L6
LA_ADSC# output valid delay
1
7
CL = 30 pf
L7
LA_WE[1:0]#output valid delay
1
7
CL = 25 pf
L8
LA_OE[1:0]# output valid delay
-1
1
CL = 25 pf
L9
LA_WE# output valid delay
1
7
CL = 25 pf
L10
LA_OE# output valid delay
1
5
CL = 25 pf
Table 14 - AC Characteristics – Local Frame Buffer SBRAM Memory Interface
96
Zarlink Semiconductor Inc.
MVTX2603
14.6
14.6.1
Data Sheet
Local Switch Database SBRAM Memory Interface
Local SBRAM Memory Interface
LB_CLK
L1
L2
LB_D[63:0]
Figure 21 - Local Memory Interface – Input Setup and Hold Timing
LB_CLK
L3-max
L3-min
LB_D[31:0]
L4-max
L4-min
LB_A[21:2]
L6-max
L6-min
LB_ADSC#
L8-max
L8-min
LB_WE[1:0]#
L9-max
L9-min
LB_OE[1:0]#
L10-max
L10-min
LB_WE#
L11-max
L11-min
LB_OE#
Figure 22 - Local Memory Interface - Output Valid Delay Timing
97
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
-100 MHz
Symbol
Parameter
Min. (ns)
Max. (ns)
Note
L1
LB_D[63:0] input set-up time
4
L2
LB_D[63:0] input hold time
1.5
L3
LB_D[63:0] output valid delay
1.5
7
CL = 25 pf
L4
LB_A[20:3] output valid delay
2
7
CL = 30 pf
L6
LB_ADSC# output valid delay
1
7
CL = 30 pf
L8
LB_WE[1:0]#output valid delay
1
7
CL = 25 pf
L9
LB_OE[1:0]# output valid delay
-1
1
CL = 25 pf
L10
LB_WE# output valid delay
1
7
CL = 25 pf
L11
LB_OE# output valid delay
1
5
CL = 25 pf
Table 15 - AC Characteristics – Local Switch Database SBRAM Memory Interface
98
Zarlink Semiconductor Inc.
MVTX2603
14.7
Data Sheet
AC Characteristics
14.7.1
Reduced Media Independent Interface
M_CLKI
M6-max
M6-min
M[23:0]_TXEN
M7-max
M7-min
M[23:0] _TXD[1:0]
Figure 23 - AC Characteristics – Reduced Media Independent Interface
M_CLKI
M2
M[23:0]_RXD
M3
M4
M[23:0]_CRS_DV
M5
Figure 24 - AC Characteristics – Reduced Media Independent Interface
-50 MHz
Symbol
Parameter
Note
Min. (ns)
Max. (ns)
M2
M[23:0]_RXD[1:0] Input Setup Time
4
M3
M[23:0]_RXD[1:0] Input Hold Time
1
M4
M[23:0]_CRS_DV Input Setup Time
4
M5
M[23:0]_CRS_DV Input Hold Time
1
M6
M[23:0]_TXEN Output Delay Time
2
11
CL = 20 pF
M7
M[23:0]_TXD[1:0] Output Delay Time
2
11
CL = 20 pF
Table 16 - AC Characteristics – Reduced Media Independent Interface
99
Zarlink Semiconductor Inc.
MVTX2603
14.7.2
Data Sheet
Gigabit Media Independent Interface - Port A
M25_TXCLK
G12-max
G12-min
M25_TXD [15:0]
G13-max
G13-min
M25_TX_EN]
G14-max
G14-min
M25_TX_ER
Figure 25 - AC Characteristics- GMII
M25_RXCLK
G1
G2
M25_RXD[15:0]
G3
G4
M25_RX_DV
G5
G6
M25_RX_ER
G7
G8
M25_RX_CRS
Figure 26 - AC Characteristics – Gigabit Media Independent Interface
-125 Mhz
Symbol
Parameter
Note
Min. (ns)
G1
M[25]_RXD[15:0] Input Setup Times
2
G2
M[25]_RXD[15:0] Input Hold Times
1
G3
M[25]_RX_DV Input Setup Times
2
G4
M[25]_RX_DV Input Hold Times
1
G5
M[25]_RX_ER Input Setup Times
2
G6
M[25]_RX_ER Input Hold Times
1
G7
M[25]_CRS Input Setup Times
2
G8
M[25]_CRS Input Hold Times
1
Max. (ns)
Table 17 - AC Characteristics – Gigabit Media Independent Interface
100
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
-125 Mhz
Symbol
Parameter
Note
Min. (ns)
Max. (ns)
G12
M[25]_TXD[15:0] Output Delay Times
1
6
CL = 20 pf
G13
M[25]_TX_EN Output Delay Times
1
6.5
CL = 20 pf
G14
M[25]_TX_ER Output Delay Times
1
6
CL = 20 pf
Table 17 - AC Characteristics – Gigabit Media Independent Interface (continued)
14.7.3
Ten Bit Interface - Port A
M25_TXCLK
TIMIN
M25_TXD [9:0]
TIMAX
Figure 27 - Gigabit TBI Interface Transmit Timing
M25_RXCLK
M25_COL
T2
T2
M25_RXD[9:0]
T3
T3
Figure 28 - Gigabit TBI Interface Receive Timing
Symbol
T1
Parameter
Min. (ns)
Max. (ns)
Note
1
6
CL = 20 pf
Max. (ns)
Note
M25_TXD[9:0] Output Delay Time
Table 18 - Output Delay Timing
Symbol
Parameter
Min. (ns)
T2
M25_RXD[9:0] Input Setup Time
3
T3
M25_RXD[9:0] Input Hold Time
3
Table 19 - Input Setup Timing
101
Zarlink Semiconductor Inc.
MVTX2603
14.7.4
Data Sheet
Gigabit Media Independent Interface - Port B
M26_TXCLK
G12-max
G12-min
M26_TXD [15:0]
G13-max
G13-min
M26_TX_EN]
G14-max
G14-min
M26_TX_ER
Figure 29 - AC Characteristics- GMII
M26_RXCLK
G1
G2
M26_RXD[15:0]
G3
G4
M26_RX_DV
G5
G6
M26_RX_ER
G7
G8
M26_RX_CRS
Figure 30 - AC Characteristics – Gigabit Media Independent Interface
-125 Mhz
Symbol
Parameter
Note
Min. (ns)
G1
M[26]_RXD[15:0] Input Setup Times
2
G2
M[26]_RXD[15:0] Input Hold Times
1
G3
M[26]_RX_DV Input Setup Times
2
G4
M[26]_RX_DV Input Hold Times
1
G5
M[26]_RX_ER Input Setup Times
2
G6
M[26]_RX_ER Input Hold Times
1
G7
M[26]_CRS Input Setup Times
2
G8
M[26]_CRS Input Hold Times
1
Max. (ns)
Table 20 - AC Characteristics – Gigabit Media Independent Interface
102
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
-125 Mhz
Symbol
Parameter
Note
Min. (ns)
Max. (ns)
G12
M[26]_TXD[15:0] Output Delay Times
1
6
CL = 20 pf
G13
M[26]_TX_EN Output Delay Times
1
6.5
CL = 20 pf
G14
M[26]_TX_ER Output Delay Times
1
6
CL = 20 pf
Table 20 - AC Characteristics – Gigabit Media Independent Interface (continued)
14.7.5
Ten Bit Interface - Port B
M26_TXCLK
TIMIN
M26_TXD [9:0]
TIMAX
Figure 31 - Gigabit TBI Interface Transmit Timing
M26_RXCLK
M26_COL
T2
T2
M26_RXD[9:0]
T3
T3
Figure 32 - Gigabit TBI Interface Timing
Symbol
T1
Parameter
Min. (ns)
Max. (ns)
Note
1
6
CL = 20 pf
Max. (ns)
Note
M26_TXD[9:0] Output Delay Time
Table 21 - Output Delay Timing
Symbol
Parameter
Min. (ns)
T2
M26_RXD[9:0] Input Setup Time
3
T3
M26_RXD[9:0] Input Hold Time
3
Table 22 - Input Setup Timing
103
Zarlink Semiconductor Inc.
MVTX2603
14.7.6
Data Sheet
LED Interface
LED_CLK
LE5-max
LE5-min
LED_SYN
LE6-max
LE6-min
LED_BIT
Figure 33 - AC Characteristics – LED Interface
Variable FREQ.
Symbol
Parameter
Note
Min. (ns)
Max. (ns)
LE5
LED_SYN Output Valid Delay
-1
7
CL = 30 pf
LE6
LED_BIT Output Valid Delay
-1
7
CL = 30 pf
Table 23 - AC Characteristics – LED Interface
14.7.7
SCANLINK SCANCOL Output Delay Timing
SCANCLK
C5-max
C5-min
SCANLINK
C7-max
C7-min
SCANCOL
Figure 34 - SCANLINK SCANCOL Output Delay Timing
SCANCLK
C1
C2
SCANLINK
C3
C4
SCANCOL
Figure 35 - SCANLINK, SCANCOL Setup Timing
104
Zarlink Semiconductor Inc.
MVTX2603
Data Sheet
-25 MHz
Symbol
Parameter
Note
Min. (ns)
Max. (ns)
C1
SCANLINK input set-up time
20
C2
SCANLINK input hold time
2
C3
SCANCOL input setup time
20
C4
SCANCOL input hold time
1
C5
SCANLINK output valid delay
0
10
CL = 30 pf
C7
SCANCOL output valid delay
0
10
CL = 30 pf
Table 24 - SCANLINK, SCANCOL Timing
14.7.8
MDIO Input Setup and Hold Timing
MDC
D1
D2
MDIO
Figure 36 - MDIO Input Setup and Hold Timing
MDC
D3-max
D3-min
MDIO
Figure 37 - MDIO Output Delay Timing
1 MHz
Symbol
Parameter
Note
Min. (ns)
D1
MDIO input setup time
10
D2
MDIO input hold time
2
D3
MDIO output delay time
1
Table 25 - MDIO Timing
105
Zarlink Semiconductor Inc.
Max. (ns)
20
CL = 50 pf
MVTX2603
14.7.9
Data Sheet
I2C Input Setup Timing
SCL
S2
S1
SDA
Figure 38 - I2C Input Setup Timing
SCL
S3-max
S3-min
SDA
Figure 39 - I2C Output Delay Timing
50 KHz
Symbol
Parameter
Note
Min. (ns)
S1
SDA input setup time
20
S2
SDA input hold time
1
S3*
SDA output delay time
4 usec
Max. (ns)
6 usec
* Open Drain Output. Low to High transistor is controlled by external pullup resistor.
Table 26 - I2C Timing
106
Zarlink Semiconductor Inc.
CL = 30 pf
MVTX2603
14.7.10
Data Sheet
Serial Interface Setup Timing
STROBE
D4
D5
D1
D1
D2
D0
D2
Figure 40 - Serial Interface Setup Timing
STROBE
D3-max
D3-min
AutoFd
Figure 41 - Serial Interface Output Delay Timing
Symbol
Parameter
Min. (ns)
D1
D0 setup time
20
D2
D0 hold time
3 µs
D3
AutoFd output delay time
D4
Strobe low time
5 µs
D5
Strobe high time
5 µs
1
Table 27 - Serial Interface Timing
107
Zarlink Semiconductor Inc.
Max. (ns)
Note
50
CL = 100 pf
E1
DIMENSION
A
A1
A2
D
D1
E
E1
b
e
MIN
MAX
2.20
2.46
0.50
0.70
1.17 REF
37.70
37.30
34.50 REF
37.70
37.30
34.50 REF
0.60
0.90
1.27
553
Conforms to JEDEC MS - 034
E
e
D
D1
A2
b
NOTE:
1. CONTROLLING DIMENSIONS ARE IN MM
2. DIMENSION "b" IS MEASURED AT THE MAXIMUM SOLDER BALL DIAMETER
3. SEATING PLANE IS DEFINED BY THE SPHERICAL CROWNS OF THE SOLDER BALLS.
4. N IS THE NUMBER OF SOLDER BALLS
5. NOT TO SCALE.
6. SUBSTRATE THICKNESS IS 0.56 MM
Package Code
ISSUE
ACN
DATE
APPRD.
Previous package codes:
For more information about all Zarlink products
visit our Web Site at
www.zarlink.com
Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively “Zarlink”) is believed to be reliable.
However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such
information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or
use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual
property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in
certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink.
This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part
of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other
information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the
capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute
any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and
suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does
not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in
significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink’s conditions of sale which are available on request.
Purchase of Zarlink’s I2C components conveys a licence under the Philips I2C Patent rights to use these components in and I2C System, provided that the system
conforms to the I2C Standard Specification as defined by Philips.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright Zarlink Semiconductor Inc. All Rights Reserved.
TECHNICAL DOCUMENTATION - NOT FOR RESALE