ZARLINK MVTX2604

MVTX2604
Managed 24-Port 10/100 Mb + 2 Port 1 Gb
Ethernet Switch
Data Sheet
Features
•
•
•
•
•
•
•
•
February 2004
Integrated Single-Chip 10/100/1000 Mbps
Ethernet Switch
24 10/100 Mbps Autosensing, Fast Ethernet
Ports with RMII or Serial Interface (7WS). Each
port can independently use one of the two
interfaces
2 Gigabit Ports with GMII, PCS, 10/100 and
stacking (2 G per port) interface options per port
Stacking port supports hot swap in managed
configuration
Supports 8/16-bit CPU interface in managed
mode
Serial interface in unmanaged mode
Supports two Frame Buffer Memory domains with
SRAM at 100 MHz
Supports memory size 2 MB, or 4 MB
Ordering Information
MVTX2604AG
-40°C to 85°C
•
•
• Static address filtering for source and/or destination
MAC
• Static MAC address not subject to aging
•
Secure mode freezes MAC address learning
Each port may independently use this mode
Full Duplex Ethernet IEEE 802.3x Flow Control
Backpressure flow control for Half Duplex ports
Supports Ethernet multicasting and broadcasting
and flooding control
Supports per-system option to enable flow
control for best effort frames even on QoSenabled ports
•
•
•
Applies centralized shared memory architecture
Up to 64 K MAC addresses
Maximum throughput is 6.4 Gbps non-blocking
High performance packet forwarding (19.047 M
packets per second) at full wire speed
•
VLAN 1 MCT
VLAN 1 MCT
Provides port based and ID tagged VLAN
support (IEEE 802.1Q), up to 255 VLANs
Supports IP Multicast with IGMP snooping
Supports spanning tree with CPU, on per port or
per VLAN basis
Packet Filtering and Port Security
•
•
• For 24 + 2, two SRAM domains (2 MB or 4 MB) are
required.
• For 24 + 2 stacking (2 G per stacking port), two ZBT
domains (2 MB or 4 MB) are required
•
•
•
•
553 Pin HSBGA
Frame Data Buffer A
SRAM (1 M / 2 M)
Frame Data Buffer B
SRAM (1 M / 2 M)
FDB Interface
FCB
24 x 10 / 100
RMII
Ports 0 - 23
Search
Engine
Frame Engine
GMII/
PCS
Port
24
LED
GMII/
PCS
Port
25
Management
Module
MCT
Link
16-bit
Parallel /
Serial
Figure 1 - MVTX2604 System Block Diagram
1
Zarlink Semiconductor Inc.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright 2003-2004, Zarlink Semiconductor Inc. All Rights Reserved.
MVTX2604
•
Data Sheet
Traffic Classification
• 4 transmission priorities for Fast Ethernet ports with 2 dropping levels
• Classification based on:
- Port based priority
- VLAN Priority field in VLAN tagged frame
- DS/TOS field in IP packet
- UDP/TCP logical ports: 8 hard-wired and 8 programmable ports, including one programmable range
•
•
The precedence of the above classifications is programmable
QoS Support
• Supports IEEE 802.1p/Q Quality of Service with 4 transmission priority queues with delay bounded, strict priority, and
WFQ service disciplines
• Provides 2 levels of dropping precedence with WRED mechanism
• User controls the WRED thresholds
• Buffer management: per class and per port buffer reservations
• Port-based priority: VLAN priority in a tagged frame can be overwritten by the priority of Port VLAN ID
•
•
•
•
•
•
•
•
•
•
•
3 port trunking groups, one for the 2 Gigabit ports, and two groups for 10/100 ports, with up to 4 10/100
ports per group
Load sharing among trunked ports can be based on source MAC and/or destination MAC. The Gigabit
trunking group has one more option, based on source port
Port Mirroring to any two ports of 0-23 in managed mode or to a dedicated mirroring port or port 23 in
unmanaged mode
Full set of LED signals provided by a serial interface, or 6 LED signals dedicated to Gigabit port status only
(without serial interface)
Built-in MIB statistics counters
Recognizes Simple Bandwidth Management (SBM) and Resource Reservation Protocol (RSVP) packets
and forwards to CPU
Hardware auto-negotiation through serial management interface (MDIO) for Ethernet ports
Built-in reset logic triggered by system malfunction
Built-in self test for internal and external SRAM
I2C EEPROM for configuration
553 BGA package
2
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
Description
The MVTX2604 is a high density, low cost, high performance, non-blocking Ethernet switch chip. A single chip
provides 24 ports at 10/100 Mbps, 2 ports at 1000 Mbps and a CPU interface for managed and unmanaged switch
applications. The Gigabit ports can also support 10/100 M and 2 G stacking modes.
The chip supports up to 64 K MAC addresses and up to 255 port-based Virtual LANs (VLANs). The centralized
shared memory architecture permits a very high performance packet forwarding rate at up to 9.524 M packets per
second at full wire speed. The chip is optimized to provide low-cost, high-performance workgroup switching.
Two Frame Buffer Memory domains utilize cost-effective, high-performance synchronous SRAM with aggregate
bandwidth of 12.8 Gbps to support full wire speed on all ports simultaneously. In the 24+2 stacking (2 G per
stacking port) configuration, 2 ZBT domains are needed.
With delay bounded, strict priority, and/or WFQ transmission scheduling, and WRED dropping schemes, the
MVTX2604 provides powerful QoS functions for various multimedia and mission-critical applications. The chip
provides 4 transmission priorities (8 priorities per Gigabit port) and 2 levels of dropping precedence. Each packet is
assigned a transmission priority and dropping precedence based on the VLAN priority field in a VLAN tagged
frame, or the DS/TOS field, or the UDP/TCP logical port fields in IP packets. The MVTX2604 recognizes a total of
16 UDP/TCP logical ports, 8 hard-wired and 8 programmable (including one programmable range).
The MVTX2604 supports 3 groups of port trunking/load sharing. One group is dedicated to the two Gigabit ports,
and the other two groups to 10/100 ports, where each 10/100 group can contain up to 4 ports. Port trunking/load
sharing can be used to group ports between interlinked switches to increase the effective network bandwidth.
In half-duplex mode all ports support backpressure flow control to minimize the risk of losing data during long
activity bursts. In full-duplex mode, IEEE 802.3x flow control is provided. The MVTX2604 also supports a persystem option to enable flow control for best effort frames, even on QoS-enabled ports.
The Physical Coding Sublayer (PCS) is integrated on-chip to provide a direct 10-bit interface for connection to
SERDES chips. The PCS can be bypassed to provide a GMII interface.
Statistical information for SNMP and the Remote Monitoring Management Information Base (RMON MIB) are
collected independently for all ports. Access to these statistical counters/registers is provided via the CPU interface.
SNMP Management frames can be received and transmitted via the CPU interface creating a complete network
management solution.
The MVTX2604 is fabricated using 0.25 micron technology. Inputs, however, are 3.3 V tolerant, and the outputs are
capable of directly interfacing to LVTTL levels. The MVTX2604 is packaged in a 553-pin Ball Grid Array package.
3
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
Table of Contents
1.0 Bock Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.1 Frame Data Buffer (FDB) Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.2 GMII/PCS MAC Module (GMAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.3 Physical Coding Sublayer (PCS) Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.4 10/100 MAC Module (RMAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1.5 CPU Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1.6 Management Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1.7 Frame Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1.8 Search Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1.9 LED Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1.10 Internal Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.0 System Configuration (Stand-alone and Stacking) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.1 Management and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.2 Managed Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.3 Register Configuration, Frame Transmission, and Frame Reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.3.1 Register Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.3.2 Rx/Tx of Standard Ethernet Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.3.3 Control Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.4 Unmanaged Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.5 I2C Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.5.1 Start Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.5.2 Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.5.3 Data Direction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.5.4 Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.5.5 Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.5.6 Stop Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.6 Synchronous Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.6.1 Write Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.6.2 Read Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.7 Stacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.0 MVTX2604 Data Forwarding Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.1 Unicast Data Frame Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.2 Multicast Data Frame Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.3 Frame Forwarding To and From CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.0 Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.2 ZBT Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.3 Detailed Memory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.4 Memory Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.0 Search Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.1 Search Engine Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.2 Basic Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.3 Search, Learning, and Aging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.3.1 MAC Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.3.2 Learning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.3.3 Aging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.3.4 VLAN Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.4 MAC Address Filtering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
5.5 Quality of Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
5.6 Priority Classification Rule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.7 Port and Tag Based VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
5.7.1 Port-Based VLAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
Table of Contents
5.7.2 Tag-Based VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
5.8 Memory Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
6.0 Frame Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
6.1 Data Forwarding Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
6.2 Frame Engine Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
6.2.1 FCB Manager. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
6.2.2 Rx Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
6.2.3 RxDMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
6.2.4 TxQ Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
6.3 Port Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
6.4 TxDMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
7.0 Quality of Service and Flow Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
7.1 Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
7.2 Four QoS Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
7.3 Delay Bound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
7.4 Strict Priority and Best Effort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
7.5 Weighted Fair Queuing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
7.6 Shaper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
7.7 Rate Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
7.8 WRED Drop Threshold Management Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
7.9 Buffer Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
7.9.1 Dropping When Buffers Are Scarce . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
7.10 MVTX2604 Flow Control Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
7.10.1 Unicast Flow Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
7.10.2 Multicast Flow Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
7.11 Mapping to IETF Diffserv Classes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
8.0 Port Trunking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
8.1 Features and Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
8.2 Unicast Packet Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
8.3 Multicast Packet Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
8.4 Unmanaged Trunking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
9.0 Port Mirroring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
9.1 Port Mirroring Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
9.2 Setting Registers for Port Mirroring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
10.0 TBI Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
10.1 TBI Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
11.0 GPSI (7WS) Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
11.1 GPSI connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
11.2 SCAN LINK and SCAN COL interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
12.0 LED Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
12.1 LED Interface Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
12.2 Port Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
12.3 LED Interface Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
13.0 Hardware Statistics Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
13.1 Hardware Statistics Counters List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
13.2 IEEE 802.3 HUB Management (RFC 1516) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
13.2.1 Event Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
13.2.1.1 Readablectet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
13.2.1.2 ReadableFrame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
13.2.1.3 FCSErrors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
13.2.1.4 AlignmentErrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
5
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
Table of Contents
13.2.1.5 FrameTooLongs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
13.2.1.6 ShortEvents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
13.2.1.7 Runts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
13.2.1.8 Collisions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
13.2.1.9 LateEvents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
13.2.1.10 VeryLongEvents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
13.2.1.11 DataRateMisatches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
13.2.1.12 AutoPartitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
13.2.1.13 TotalErrors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
13.3 IEEE – 802.1 Bridge Management (RFC 1286) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
13.3.1 Event Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
13.3.1.1 InFrames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
13.3.1.2 OutFrames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
13.3.1.3 InDiscards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
13.3.1.4 DelayExceededDiscards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
13.3.1.5 MtuExceededDiscards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
13.4 RMON – Ethernet Statistic Group (RFC 1757) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
13.4.1 Event Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
13.4.1.1 Drop Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
13.4.1.2 Octets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
13.4.1.3 BroadcastPkts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
13.4.1.4 MulticastPkts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
13.4.1.5 CRCAlignErrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
13.4.1.6 UndersizePkts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
13.4.1.7 OversizePkts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
13.4.1.8 Fragments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
13.4.1.9 Jabbers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
13.4.1.10 Collisions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
13.4.1.11 Packet Count for Different Size Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
13.5 Miscellaneous Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
14.0 Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
14.1 MVTX2604 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
14.2 Directly Accessed Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
14.2.1 INDEX_REG0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
14.2.2 INDEX_REG1 (only needed for 8-bit mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
14.2.3 DATA_FRAME_REG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
14.2.4 CONTROL_FRAME_REG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
14.2.5 COMMAND&STATUS Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
14.2.6 Interrupt Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
14.2.7 Control Command Frame Buffer1 Access Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
14.2.8 Control Command Frame Buffer2 Access Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
14.3 Indirectly Accessed registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
14.4 Group 0 Address MAC Ports Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
14.4.1 ECR1Pn: Port N Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
14.4.2 ECR2Pn: Port N Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
14.4.3 GGControl – Extra GIGA Port Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
14.5 Group 1 Address VLAN Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
14.5.1 AVTCL – VLAN Type Code Register Low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
14.5.2 AVTCH – VLAN Type Code Register High . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
14.5.3 PVMAP00_0 – Port 00 Configuration Register 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
14.5.4 PVMAP00_1 – Port 00 Configuration Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
14.5.5 PVMAP00_2 – Port 00 Configuration Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
6
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
Table of Contents
14.5.6 PVMAP00_3 – Port 00 Configuration Register 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
14.6 Port Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
14.6.1 PVMODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
14.6.2 PVROUTE 0. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
14.6.3 PVROUTE1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
14.6.4 PVROUTE2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
14.6.5 PVROUTE3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
14.6.6 PVROUTE4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
14.6.7 PVROUTE5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
14.6.8 PVROUTE6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
14.6.9 PVROUTE7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
14.7 Group 2 Address Port Trunking Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
14.7.1 TRUNK0_L – Trunk group 0 Low (Managed mode only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
14.7.2 TRUNK0_M – Trunk group 0 Medium (Managed mode only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
14.7.3 TRUNK0_H – Trunk group 0 High (Managed mode only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
14.7.4 TRUNK0_MODE– Trunk group 0 mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
14.7.5 TRUNK0_HASH0 – Trunk group 0 hash result 0 destination port number . . . . . . . . . . . . . . . . . . 78
14.7.6 TRUNK0_HASH1 – Trunk group 0 hash result 1 destination port number . . . . . . . . . . . . . . . . . . 78
14.7.7 TRUNK0_HASH2 – Trunk group 0 hash result 2 destination port number . . . . . . . . . . . . . . . . . . 78
14.7.8 TRUNK0_HASH3 – Trunk group 0 hash result 3 destination port number . . . . . . . . . . . . . . . . . . 79
14.7.9 TRUNK1_L – Trunk group 1 Low (Managed mode only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
14.7.10 TRUNK1_M – Trunk group 1 Medium (Managed mode only) . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
14.7.11 TRUNK1_H – Trunk group 1 High (Managed mode only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
14.7.12 TRUNK1_MODE – Trunk group 1 mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
14.7.13 TRUNK1_HASH0 – Trunk group 1 hash result 0 destination port number . . . . . . . . . . . . . . . . . 80
14.7.14 TRUNK1_HASH1 – Trunk group 1 hash result 1 destination port number . . . . . . . . . . . . . . . . . 80
14.7.15 TRUNK1_HASH2 – Trunk group 1 hash result 2 destination port number . . . . . . . . . . . . . . . . . 80
14.7.16 TRUNK1_HASH3 – Trunk group 1 hash result 3 destination port number . . . . . . . . . . . . . . . . . 80
14.7.17 TRUNK2_MODE – Trunk group 2 mode (Gigabit ports 1 and 2). . . . . . . . . . . . . . . . . . . . . . . . . 80
14.7.18 TRUNK2_HASH0 – Trunk group 2 hash result 0 destination port number . . . . . . . . . . . . . . . . . 81
14.7.19 TRUNK2_HASH1 – Trunk group 2 hash result 1 destination port number . . . . . . . . . . . . . . . . . 81
14.7.20 Multicast Hash Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
14.7.20.1 Multicast_HASH0-1 – Multicast hash result 0 mask byte 1 . . . . . . . . . . . . . . . . . . . . . . . . 82
14.7.20.2 Multicast_HASH0-2 – Multicast hash result 0 mask byte 2 . . . . . . . . . . . . . . . . . . . . . . . . 82
14.7.20.3 Multicast_HASH0-3 – Multicast hash result 0 mask byte 3 . . . . . . . . . . . . . . . . . . . . . . . . 82
14.7.20.4 Multicast_HASH1-0 – Multicast hash result 1 mask byte 0 . . . . . . . . . . . . . . . . . . . . . . . . 82
14.7.20.5 Multicast_HASH1-1 – Multicast hash result 1 mask byte 1 . . . . . . . . . . . . . . . . . . . . . . . . 82
14.7.20.6 Multicast_HASH1-2 – Multicast hash result 1 mask byte 2 . . . . . . . . . . . . . . . . . . . . . . . . 82
14.7.20.7 Multicast_HASH1-3 – Multicast hash result 1 mask byte 3 . . . . . . . . . . . . . . . . . . . . . . . . 82
14.7.20.8 Multicast_HASH2-0 – Multicast hash result 2 mask byte 0 . . . . . . . . . . . . . . . . . . . . . . . . 83
14.7.20.9 Multicast_HASH2-1 – Multicast hash result 2 mask byte 1 . . . . . . . . . . . . . . . . . . . . . . . . 83
14.7.20.10 Multicast_HASH2-2 – Multicast hash result 2 mask byte 2 . . . . . . . . . . . . . . . . . . . . . . . 83
14.7.20.11 Multicast_HASH2-3 – Multicast hash result 2 mask byte 3 . . . . . . . . . . . . . . . . . . . . . . . 83
14.7.20.12 Multicast_HASH3-0 – Multicast hash result 3 mask byte 0 . . . . . . . . . . . . . . . . . . . . . . . 83
14.7.20.13 Multicast_HASH3-1 – Multicast hash result 3 mask byte 1 . . . . . . . . . . . . . . . . . . . . . . . 83
14.7.20.14 Multicast_HASH3-2 – Multicast hash result 3 mask byte 2 . . . . . . . . . . . . . . . . . . . . . . . 83
14.7.20.15 Multicast_HASH3-3 – Multicast hash result 3 mask byte 3 . . . . . . . . . . . . . . . . . . . . . . . 84
14.8 Group 3 Address CPU Port Configuration Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
14.8.1 MAC0 – CPU Mac address byte 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
14.8.2 MAC1 – CPU Mac address byte 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
14.8.3 MAC2 – CPU Mac address byte 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
14.8.4 MAC3 – CPU Mac address byte 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
7
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
Table of Contents
14.8.5 MAC4 – CPU Mac address byte 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
14.8.6 MAC5 – CPU Mac address byte 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
14.8.7 INT_MASK0 – Interrupt Mask 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
14.8.8 INTP_MASK0 – Interrupt Mask for MAC Port 0,1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
14.8.9 INTP_MASK1 – Interrupt Mask for MAC Port 2,3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
14.8.10 INTP_MASK2 – Interrupt Mask for MAC Port 4,5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
14.8.11 INTP_MASK3 – Interrupt Mask for MAC Port 6,7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
14.8.12 INTP_MASK4 – Interrupt Mask for MAC Port 8,9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
14.8.13 INTP_MASK5 – Interrupt Mask for MAC Port 10,11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
14.8.14 INTP_MASK6 – Interrupt Mask for MAC Port 12,13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
14.8.15 INTP_MASK7 – Interrupt Mask for MAC Port 14,15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
14.8.16 INTP_MASK8 – Interrupt Mask for MAC Port 16,17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
14.8.17 NTP_MASK9 – Interrupt Mask for MAC Port 18,19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
14.8.18 INTP_MASK10 – Interrupt Mask for MAC Port 20,21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
14.8.19 INTP_MASK11 – Interrupt Mask for MAC Port 22,23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
14.8.20 INTP_MASK12 – Interrupt Mask for MAC Port G1,G2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
14.8.21 RQS – Receive Queue Select CPU Address:h323). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
14.8.22 RQSS – Receive Queue Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
14.8.23 TX_AGE – Tx Queue Aging timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
14.9 Group 4 Address Search Engine Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
14.9.1 AGETIME_LOW – MAC address aging time Low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
14.9.2 AGETIME_HIGH –MAC address aging time High . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
14.9.3 V_AGETIME – VLAN to Port aging time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
14.9.4 SE_OPMODE – Search Engine Operation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
14.9.5 SCAN – SCAN Control Register (default 00) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
14.10 Group 5 Address Buffer Control/QOS Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
14.10.1 FCBAT – FCB Aging Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
14.10.2 QOSC – QOS Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
14.10.3 FCR – Flooding Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
14.10.4 AVPML – VLAN Tag Priority Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
14.10.5 AVPMM – VLAN Priority Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
14.10.6 AVPMH – VLAN Priority Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
14.10.7 TOSPML – TOS Priority Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
14.10.8 TOSPMM – TOS Priority Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
14.10.9 TOSPMH – TOS Priority Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
14.10.10 AVDM – VLAN Discard Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
14.10.11 TOSDML – TOS Discard Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
14.10.12 BMRC - Broadcast/Multicast Rate Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
14.10.13 UCC – Unicast Congestion Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
14.10.14 MCC – Multicast Congestion Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
14.10.15 PR100 – Port Reservation for 10/100 ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
14.10.16 PRG – Port Reservation for Giga ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
14.10.17 SFCB – Share FCB Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
14.10.18 C2RS – Class 2 Reserve Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
14.10.19 C3RS – Class 3 Reserve Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
14.10.20 C4RS – Class 4 Reserve Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
14.10.21 C5RS – Class 5 Reserve Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
14.10.22 C6RS – Class 6 Reserve Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
14.10.23 C7RS – Class 7 Reserve Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
14.10.24 QOSCn - Classes Byte Limit Set 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
14.10.25 Classes Byte Limit Set 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
14.10.26 Classes Byte Limit Set 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
8
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
Table of Contents
14.10.27 Classes Byte Limit Set 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
14.10.28 Classes Byte Limit Giga Port 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
14.10.29 Classes Byte Limit Giga Port 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
14.10.30 Classes WFQ Credit Set 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
14.10.31 Classes WFQ Credit Set 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
14.10.32 Classes WFQ Credit Set 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
14.10.33 Classes WFQ Credit Set 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
14.10.34 Classes WFQ Credit Port G1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
14.10.35 Classes WFQ Credit Port G2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
14.10.36 Class 6 Shaper Control Port G1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
14.10.37 Class 6 Shaper Control Port G2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
14.10.38 RDRC0 – WRED Rate Control 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
14.10.39 RDRC1 – WRED Rate Control 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
14.10.40 User Defined Logical Ports and Well Known Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
14.10.40.1 USER_PORT0_(0~7) – User Define Logical Port (0~7) . . . . . . . . . . . . . . . . . . . . . . . . 105
14.10.40.2 USER_PORT_[1:0]_PRIORITY - User Define Logic Port 1 and 0 Priority . . . . . . . . . . 105
14.10.40.3 USER_PORT_[3:2]_PRIORITY - User Define Logic Port 3 and 2 Priority . . . . . . . . . . 106
14.10.40.4 USER_PORT_[5:4]_PRIORITY - User Define Logic Port 5 and 4 Priority . . . . . . . . . . 106
14.10.40.5 USER_PORT_[7:6]_PRIORITY - User Define Logic Port 7 and 6 Priority . . . . . . . . . . 106
14.10.40.6 USER_PORT_ENABLE[7:0] – User Define Logic 7 to 0 Port Enables . . . . . . . . . . . . . 106
14.10.40.7 WELL_KNOWN_PORT[1:0] PRIORITY- Well Known Logic Port 1 and 0 Priority . . . . 106
14.10.40.8 WELL_KNOWN_PORT[3:2] PRIORITY- Well Known Logic Port 3 and 2 Priority . . . . 107
14.10.40.9 WELL_KNOWN_PORT [5:4] PRIORITY- Well Known Logic Port 5 and 4 Priority . . . . 107
14.10.40.10 WELL_KNOWN_PORT [7:6] PRIORITY- Well Known Logic Port 7 and 6 Priority . . . 107
14.10.40.11 WELL KNOWN_PORT_ENABLE [7:0] – Well Known Logic 7 to 0 Port Enables . . . . 108
14.10.40.12 RLOWL – User Define Range Low Bit 7:0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
14.10.40.13 RLOWH – User Define Range Low Bit 15:8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
14.10.40.14 RHIGHL – User Define Range High Bit 7:0. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
14.10.40.15 RHIGHH – User Define Range High Bit 15:8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
14.10.40.16 RPRIORITY – User Define Range Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
14.10.41 CPUQOSC123 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
14.11 Group 6 Address MISC Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
14.11.1 MII_OP0 – MII Register Option 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
14.11.2 MII_OP1 – MII Register Option 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
14.11.3 FEN – Feature Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
14.11.4 MIIC0 – MII Command Register 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
14.11.5 MIIC1 – MII Command Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
14.11.6 MIIC2 – MII Command Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
14.11.7 MIIC3 – MII Command Register 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
14.11.8 MIID0 – MII Data Register 0. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
14.11.9 MIID1 – MII Data Register 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
14.11.10 LED Mode – LED Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
14.11.11 DEVICE Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
14.11.12 CHECKSUM - EEPROM Checksum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
14.12 Group 7 Address Port Mirroring Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
14.12.1 MIRROR1_SRC - Port Mirror source port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
14.12.2 MIRROR1_DEST – Port Mirror destination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
14.12.3 MIRROR2_SRC – Port Mirror source port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
14.12.4 MIRROR2_DEST – Port Mirror destination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
14.13 Group F Address CPU Access Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
14.13.1 GCR-Global Control Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
14.13.2 DCR-Device Status and Signature Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
9
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
Table of Contents
14.3.13 DCR1-Giga port status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
14.3.14 DPST – Device Port Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
14.3.15 DTST – Data read back register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
14.3.16 DA – DA Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
14.4 TBI Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
14.4.1 Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
14.4.2 Status Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
14.4.3 Advertisement Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
14.4.4 Link Partner Ability Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
14.4.5 Expansion Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
14.4.6 Extended Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
15.0 BGA and Ball Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
15.1 BGA Views (Top-View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
15.1.1 Encapsulated view in unmanaged mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
15.1.2 Encapsulated view in managed mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
15.2 Ball – Signal Descriptions in Managed Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
15.2.1 Ball Signal Descriptions in Managed Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
15.2.2 Ball – Signal Descriptions in Unmanaged Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
15.3 Ball – Signal Name in Unmanaged Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
15.4 Ball – Signal Name in Managed Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
15.5 AC/DC Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
15.5.1 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
15.5.2 DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
15.5.3 Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
15.5.4 Typical Reset & Bootstrap Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
15.5.5 Typical CPU Timing Diagram for a CPU Write Cycle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
15.5.6 Typical CPU Timing Diagram for a CPU Read Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
15.6 Local Frame Buffer SBRAM Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
15.6.1 Local SBRAM Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
15.7 Local Switch Database SBRAM Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
15.7.1 Local SBRAM Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
15.8 AC Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
15.8.1 Reduced Media Independent Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
15.8.2 Gigabit Media Independent Interface - Port A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
15.8.3 Ten Bit Interface - Port A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
15.8.4 Gigabit Media Independent Interface - Port B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
15.8.5 Ten Bit Interface - Port B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
15.8.6 LED Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
15.8.7 SCANLINK SCANCOL Output Delay Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
15.9 MDIO Input Setup and Hold Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
15.9.1 I2C Input Setup Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
15.9.2 Serial Interface Setup Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
10
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
List of Figures
Figure 1 - MVTX2604 System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Figure 2 - Overview of the MVTX2604 CPU Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 3 - Data Transfer Format for I2C Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 4 - MVTX2604 SRAM Interface Block Diagram (DMAs for 10/1000 Ports Only) . . . . . . . . . . . . . . . . . . . . 24
Figure 5 - Priority Classification Rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 6 - Memory Configuration For: 2 Banks, 1 Layer, 2 MB Total . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 7 - Memory Configuration For: 2 Banks, 2 Layers, 4 MB Total . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 8 - Memory Configuration For: 2 Banks, 1 Layer, 4 MB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 9 - Memory Configuration For: 2 Banks, 2 Layers, 4 MB Total . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 10 - Memory Configuration For: 2 Banks, 1 Layer, 4 MB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 11 - Buffer Partition Scheme Used to Implement MVTX2604 AG Buffer Management . . . . . . . . . . . . . . . 41
Figure 12 - TBI Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Figure 13 - GPSI (7WS) Mode Connection Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Figure 14 - SCAN LINK and SCAN COLLISON Status Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Figure 15 - Timing Diagram of LED Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Figure 16 - Typical Reset & Bootstrap Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Figure 17 - Typical CPU Timing Diagram for a CPU Write Cycle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Figure 18 - Typical CPU Timing Diagram for a CPU Read Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Figure 19 - Local Memory Interface – Input Setup and Hold Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Figure 20 - Local Memory Interface - Output Valid Delay Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Figure 21 - Local Memory Interface – Input Setup and Hold Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Figure 22 - Local Memory Interface - Output Valid Delay Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Figure 23 - AC Characteristics – Reduced Media Independent Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Figure 24 - AC Characteristics – Reduced Media Independent Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Figure 25 - AC Characteristics- GMII . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Figure 26 - AC Characteristics – Gigabit Media Independent Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Figure 27 - Gigabit TBI Interface Transmit Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Figure 28 - Gigabit TBI Interface Receive Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Figure 29 - AC Characteristics- GMII . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Figure 30 - AC Characteristics – Gigabit Media Independent Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Figure 31 - Gigabit TBI Interface Transmit Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Figure 32 - Gigabit TBI Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Figure 33 - AC Characteristics – LED Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
Figure 34 - SCANLINK SCANCOL Output Delay Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Figure 35 - SCANLINK, SCANCOL Setup Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Figure 36 - MDIO Input Setup and Hold Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
Figure 37 - MDIO Output Delay Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
Figure 38 - I2C Input Setup Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Figure 39 - I2C Output Delay Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Figure 40 - Serial Interface Setup Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Figure 41 - Serial Interface Output Delay Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
11
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
List of Tables
Table 1 - VLAN Index Mapping Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Table 2 - LAN Index Port Association Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 3 - PVMAP Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Table 4 - Supported Memory Configurations (SBRAM Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Table 5 - Supported Memory Configurations (ZBT Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Table 6 - Options for Memory Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Table 7 - Two-dimensional World Traffic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Table 8 - Four QoS Configurations for a 10/100 Mbps Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Table 9 - Four QoS Configurations for a Gigabit Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Table 10 - WRED Drop Thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Table 11 - Mapping between MVTX2604 and IETF Diffserv Classes for Gigabit Ports . . . . . . . . . . . . . . . . . . . . . 43
Table 12 - Mapping between MVTX2604 and IETF Diffserv Classes for 10/100 Ports . . . . . . . . . . . . . . . . . . . . . 43
Table 13 - MVTX2604 Features Enabling IETF Diffserv Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table 14 - Reset & Bootstrap Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Table 15 - AC Characteristics – Local Frame Buffer SBRAM Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . . 161
Table 16 - AC Characteristics – Local Switch Database SBRAM Memory Interface . . . . . . . . . . . . . . . . . . . . . . 163
Table 17 - AC Characteristics – Reduced Media Independent Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Table 18 - AC Characteristics – Gigabit Media Independent Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Table 19 - Output Delay Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Table 20 - Input Setup Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Table 21 - AC Characteristics – Gigabit Media Independent Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Table 22 - Output Delay Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Table 23 - Input Setup Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Table 24 - AC Characteristics – LED Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
Table 25 - SCANLINK, SCANCOL Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Table 26 - MDIO Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
Table 27 - I2C Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Table 28 - Serial Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
12
Zarlink Semiconductor Inc.
MVTX2604
1.0
Bock Functionality
1.1
Frame Data Buffer (FDB) Interfaces
Data Sheet
The FDB interface supports pipelined synchronous burst SRAM (SBRAM) memory at 100 MHz. To ensure a nonblocking switch two memory domains are required. Each domain has a 64 bit wide memory bus. At 100 MHz, the
aggregate memory bandwidth is 12.8 Gbps which is enough to support 24 10/100 Mbps and 2 Gigabit ports at full
wire speed switching. For 24 + 2 stacking application, pipelined ZBT-SRAM memory running at 125 MHz is
required.
The Switching Database is also located in the external SRAM; it is used for storing MAC addresses and their
physical port number. It is duplicated and stored in both memory domains. Therefore, when the system updates the
contents of the switching database it has to write the entry to both domains at the same time.
1.2
GMII/PCS MAC Module (GMAC)
The GMII/PCS Media Access Control (MAC) module provides the necessary buffers and control interface between
the Frame Engine (FE) and the external physical device (PHY).
The MVTX2604 GMAC implements both GMII and MII interface, which offers a simple migration from 10/100 to 1 G.
The GMAC of the MVTX2604 meets the IEEE 802.3Z specification. It is able to operate in 10 M/100 M either Half or
Full Duplex mode with a back pressure/flow control mechanism or in 1G Full duplex mode with flow control
mechanism. Furthermore, it will automatically retransmit upon collision for up to 16 total transmissions. PHY
addresses for GMAC are 01h and 02h.
For fiber optics media, the MVTX2604 implements the Physical Code Sublayer (PCS) interface. The PCS includes
an 8B10B encoder and decoder, auto-negotiation and Ten Bit Interface (TBI)
1.3
Physical Coding Sublayer (PCS) Interface
For the MVTX2604, the 1000BASE-X PCS Interface is designed internally and may be utilized in the absence of a
GMII. The PCS incorporates all the functions required by the GMII to include encoding (decoding) 8B GMII data to
(from) 8B/10B TBI format for PHY communication and generating Collision Detect (COL) signals for half-duplex
mode. It also manages the Auto negotiation process by informing the management entity that the PHY is ready for
communications. The on-chip TBI may be disabled if TBI exists within the Gigabit PHY. The TBI interface provides
a uniform interface for all 1000 Mbps PHY implementations.
The PCS comprises the PCS Transmit, Synchronization, PCS Receive and Auto negotiation processes for
1000BASE-X.
The PCS Transmit process sends the TBI signals TXD [9:0] to the physical medium and generates the GMII
Collision Detect (COL) signal based on whether a reception is occurring simultaneously with transmission.
Additionally, the Transmit process generates an internal “transmitting” flag and monitors Auto negotiation to
determine whether to transmit data or to reconfigure the link.
The PCS Synchronization process determines whether or not the receive channel is operational.
The PCS Receive process generates RXD [7:0] on the GMII from the TBI data [9:0], and the internal “receiving” flag
for use by the Transmit processes.
The PCS Auto negotiation process allows the MVTX2604 to exchange configuration information between two
devices that share a link segment and to automatically configure the link for the appropriate speed of operation for
both devices.
15
Zarlink Semiconductor Inc.
MVTX2604
1.4
Data Sheet
10/100 MAC Module (RMAC)
The 10/100 Media Access Control module provides the necessary buffers and control interface between the Frame
Engine (FE) and the external physical device (PHY). The MVTX2604 has two interfaces, RMII or Serial (only for
10 M). The 10/100 MAC of the MVTX2604 device meets the IEEE 802.3 specification. It is able to operate in either
Half or Full Duplex mode with a back pressure/flow control mechanism. In addition, it will automatically retransmit
upon collision for up to 16 total transmissions. The PHY addresses for 24 10/100 MAC are from 08h to 1Fh.
1.5
CPU Interface Module
One extra port is dedicated to the CPU via the CPU interface module. The CPU interface utilizes a 16/8-bit bus in
managed mode (Bootstrap pin TSTOUT6 makes the selection). It also supports a serial and an I2C interface, which
provides an easy way to configure the system if unmanaged.
1.6
Management Module
The CPU can send a control frame to access or configure the internal network management database. The
Management Module decodes the control frame and executes the functions requested by the CPU.
1.7
Frame Engine
The main function of the frame engine is to forward a frame to its proper destination port or ports. When a frame
arrives, the frame engine parses the frame header (64 bytes) and formulates a switching request which is sent to
the search engine to resolve the destination port. The arriving frame is moved to the FDB. After receiving a switch
response from the search engine, the frame engine performs transmission scheduling based on the frame’s priority.
The frame engine forwards the frame to the MAC module when the frame is ready to be sent.
1.8
Search Engine
The Search Engine resolves the frame’s destination port or ports according to the destination MAC address (L2) or
IP multicast address (IP multicast packet) by searching the database. It also performs MAC learning, priority
assignment and trunking functions.
1.9
LED Interface
The LED interface provides a serial interface for carrying 24 + 2 port status signals. It can also provide direct status
pins (6) for the two Gigabit ports.
1.10
Internal Memory
Several internal tables are required and are described as follows:
•
•
•
Frame Control Block (FCB) - Each FCB entry contains the control information of the associated frame
stored in the FDB, e.g., frame size, read/write pointer, transmission priority, etc.
Network Management (NM) Database - The NM database contains the information in the statistics counters
and MIB.
MAC address Control Table (MCT) Link Table - The MCT Link Table stores the linked list of MCT entries that
have collisions in the external MAC Table.
Note that the external MAC table is located in the external SRAM Memory.
16
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
2.0
System Configuration (Stand-alone and Stacking)
2.1
Management and Configuration
Two modes are supported in the MVTX2604: managed and unmanaged. In managed mode, the MVTX2604 uses
an 8 or 16 bit CPU interface very similar to the Industry Standard Architecture (ISA) specification. In unmanaged
mode, the MVTX2604 has no CPU but can be configured by EEPROM using an I2C interface at bootup, or via a
synchronous serial interface otherwise.
2.2
Managed Mode
In managed mode, the MVTX2604 uses an 8 or 16 bit CPU interface very similar to the ISA bus. The MVTX2604
CPU interface provides for easy and effective management of the switching system. Figure 2 provides an overview
of the CPU interface.
INDEX REG 1
(Addr = 001)
INDEX REG 0
(Addr = 000)
CONFIG
DATA REG
(Addr = 010)
8 bit internal
data bus
FRAME DATA REG
(Addr = 011)
CONTROL
BLOCK REG
8/16 bit internal
data bus
8/16 bit internal
data bus
16 bit internal
address bus
INTERNAL
CONFIGURE
REGISTERS
CPU
FRAME
RECEIVE
FIFO
CPU
FRAME
TRANSMIT
FIFO
CONTROL
COMMAND
FRAME
RECEIVE
FIFO
CONTROL
COMMAND
FRAME
TRANSMIT
FIFO
1 AND 2
SYNOCHRONOUS
SERIAL
INTERFACE
Figure 2 - Overview of the MVTX2604 CPU Interface
2.3
Register Configuration, Frame Transmission, and Frame Reception
2.3.1
Register Configuration
The MVTX2604 has many programmable parameters, covering such functions as QoS weights, VLAN control and
port mirroring setup. In managed mode, the CPU interface provides an easy way of configuring these parameters.
The parameters are contained in 8-bit configuration registers. The MVTX2604 allows indirect access to these
registers, as follows:
•
If operating in 8 bits-interface mode, two “index” registers (addresses 000 and 001) need to be written to
indicate the desired 8-bit register address. In 16-bit mode, only one register (address 000) needs to be
written for the desired 16-bit register address.
17
Zarlink Semiconductor Inc.
MVTX2604
•
•
Data Sheet
To indirectly configure the register addressed by the two index registers, a “configure data” register (address
010) must be written with the desired 8-bit data.
Similarly, to read the value in the register addressed by the two index registers, the “configure data” register
can now simply be read.
In summary, access to the many internal registers is carried out simply by directly accessing only three registers –
two registers to indicate the address of the desired parameter, and one register to read or write a value. Of course,
because there is only one bus master, there can never be any conflict between reading and writing the
configuration registers.
2.3.2
Rx/Tx of Standard Ethernet Frames
The CPU interface is also responsible for receiving and transmitting standard Ethernet frames to and from the CPU.
To transmit a frame from the CPU:
•
•
The CPU writes a “data frame” register (address 011) with the data it wants to transmit (minimum 64 bytes).
After writing all the data, it then writes the frame size, destination port number and frame status.
The MVTX2604 forwards the Ethernet frame to the desired destination port, no longer distinguishing the fact
that the frame originated from the CPU.
To receive a frame into the CPU:
•
•
•
The CPU receives an interrupt when an Ethernet frame is available to be received.
Frame information arrives first in the data frame register. This includes source port number, frame size and
VLAN tag.
The actual data follows the frame information. The CPU uses the frame size information to read the frame
out.
In summary, receiving and transmitting frames to and from the CPU is a simple process that uses one direct access
register only.
2.3.3
Control Frames
In addition to standard Ethernet frames described in the preceding section, the CPU is also called upon to handle
special “Control frames,” generated by the MVTX2604 and sent to the CPU. These proprietary frames are related
to such tasks as statistics collection, MAC address learning and aging etc. All Control frames are up to 40 bytes
long. Transmitting and receiving these frames is similar to transmitting and receiving Ethernet frames, except that
the register accessed is the “Control frame data” register (address 111).
Specifically, there are eight types of control frames generated by the CPU and sent to the MVTX2604:
•
•
•
•
•
•
•
•
Memory read request
Memory write request
Learn MAC address
Delete MAC address
Search MAC address
Learn IP Multicast address
Delete IP Multicast address
Search IP Multicast address
Note: Memory read and write requests by the CPU may include VLAN table, spanning tree, statistic counters and
similar updates.
In addition, there are nine types of Control frames generated by the MVTX2604 and sent to the CPU:
•
Interrupt CPU when statistics counter rolls over
18
Zarlink Semiconductor Inc.
MVTX2604
•
•
•
•
•
•
•
•
Data Sheet
Response to memory read request from CPU
Learn MAC address
Delete MAC address
Delete IP Multicast address
New VLAN port
Age out VLAN port
Response to search MAC address request from CPU
Response to search IP Multicast address request from CPU
The format of the Control Frame is described in the processor interface application note.
2.4
Unmanaged Mode
In unmanaged mode, the MVTX2604 can be configured by EEPROM (24C02 or compatible) via an I2C interface at
boot time, or via a synchronous serial interface during operation.
2.5
I2C Interface
The I2C interface uses two bus lines, a serial data line (SDA) and a serial clock line (SCL). The SCL line carries the
control signals that facilitate the transfer of information from EEPROM to the switch. Data transfer is 8-bit serial and
bidirectional at 50 Kbps. Data transfer is performed between master and slave IC using a request /
acknowledgment style of protocol. The master IC generates the timing signals and terminates data transfer.
Figure 3 depicts the data transfer format.
START
SLAVE ADDRESS
R/W
ACK
DATA 1 (8 bits)
ACK
DATA 2
ACK
DATA M
ACK
STOP
Figure 3 - Data Transfer Format for I 2C Interface
2.5.1
Start Condition
Generated by the master (in our case, the MVTX2604). The bus is considered to be busy after the Start condition is
generated. The Start condition occurs if while the SCL line is High, there is a High-to-Low transition of the SDA line.
Other than in the Start condition (and Stop condition), the data on the SDA line must be stable during the High
period of SCL. The High or Low state of SDA can only change when SCL is Low. In addition, when the I2C bus is
free, both lines are High.
2.5.2
Address
The first byte after the Start condition determines which slave the master will select. The slave in our case is the
EEPROM. The first seven bits of the first data byte make up the slave address.
2.5.3
Data Direction
The eighth bit in the first byte after the Start condition determines the direction (R/W) of the message. A master
transmitter sets this bit to W; a master receiver sets this bit to R.
2.5.4
Acknowledgment
Like all clock pulses, the acknowledgment-related clock pulse is generated by the master. However, the transmitter
releases the SDA line (High) during the acknowledgment clock pulse. Furthermore, the receiver must pull down the
SDA line during the acknowledge pulse so that it remains stable Low during the High period of this clock pulse. An
acknowledgment pulse follows every byte transfer.
19
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
If a slave receiver does not acknowledge after any byte, then the master generates a Stop condition and aborts the
transfer.
If a master receiver does not acknowledge after any byte, then the slave transmitter must release the SDA line to let
the master generate the Stop condition.
2.5.5
Data
After the first byte containing the address, all bytes that follow are data bytes. Each byte must be followed by an
acknowledge bit. Data is transferred MSB first.
2.5.6
Stop Condition
Generated by the master. The bus is considered to be free after the Stop condition is generated. The Stop condition
occurs if while the SCL line is High, there is a Low-to-High transition of the SDA line.
The I2C interface serves the function of configuring the MVTX2604 at boot time. The master is the MVTX2604 and
the slave is the EEPROM memory.
2.6
Synchronous Serial Interface
The synchronous serial interface serves the function of configuring the MVTX2604, not at boot time, but via a PC.
The PC serves as master and the MVTX2604 serves as slave. The protocol for the synchronous serial interface is
nearly identical to the I2C protocol. The main difference is that there is no acknowledgment bit after each byte of
data transferred.
The unmanaged MVTX2604 uses a synchronous serial interface to program the internal registers. To reduce the
number of signals required, the register address, command and data are shifted in serially through the D0 pin.
STROBE- pin is used as the shift clock. AUTOFD- pin is used as data return path.
Each command consists of four parts.
•
•
•
•
START pulse
Register Address
Read or Write command
Data to be written or read back
Any command can be aborted in the middle by sending a ABORT pulse to the MVTX2600AG.
A START command is detected when D0 is sampled high when STROBE- rise and D0 is sampled low when
STROBE- fall.
An ABORT command is detected when D0 is sampled low when STROBE- rise and D0 is sampled high when
STROBE- fall.
20
Zarlink Semiconductor Inc.
MVTX2604
2.6.1
Data Sheet
Write Command
STROBE2 extra
clock
cycles
after
2 Extra
clocks
after last
last transfer
transfer
A0 A1
A1 A2
A2 ...
A0
D0
START
2.6.2
A11 W
A9
A9 A10
A10 A11
ADDRESS
D0 D1 D2 D3 D4 D5 D6 D7
COMMAND
DATA
Read Command
STROBE-
A0 A1
A1 A2
A0
A2
D0
START
AUTOFD-
A10 A11
A11
A9 A10
... A9
ADDRESS
R
COMMAND
DATA
D0 D1 D2 D3 D4 D5 D6 D7
All registers in MVTX2600AG can be modified through this synchronous serial interface.
2.7
Stacking
The MVTX2604 supports expanded port count by providing stacking capabilities. The Gigabit port is used as the
link between boxes, and each Gigabit port can be accelerated to 2 Gpbs if desired (in conjunction with ZBT memory
domains at 125 MHz). If both Gigabit ports are used for this purpose, this provides a total of 4 Gbps of bandwidth
between devices.
In addition to a standard back-to-back configuration of devices, the MVTX2604 also provides more powerful
stacking alternatives:
•
•
Unidirectional ring configuration. Up to 32 devices. Devices are connected by one Gigabit link, which can be
accelerated to 2 Gbps, if desired. Flow control cannot be enabled in this configuration, because of the
inherent inefficiency in sending flow control messages upstream in a unidirectional ring.
Bidirectional ring configuration. Up to 32 devices. Devices are connected by two Gigabit links, forming two
rings, one clockwise and one counter clockwise. The total outgoing bandwidth can be as much as 4 Gbps.
Flow control may be enabled in this configuration. The outgoing direction of a packet (clockwise or counter
clockwise) is selected using a hash key for load distribution. The hash key can be a function of source MAC
address, destination MAC address, both MAC addresses, or source port. This configuration provides faulttolerance when one of the stacking links fail.
21
Zarlink Semiconductor Inc.
MVTX2604
MVTX2600
•
MVTX2600
...
Data Sheet
MVTX2600
Cascade Stacking configuration. Up to 32 devices. Devices are connected to form a list configuration.
Devices are connected by two Gigabit links, except the two devices at both ends, where one Gigabit port is
used as an uplink port. Flow control may be enabled in this configuration.
MVTX2600
MVTX2600
3.0
MVTX2604 Data Forwarding Protocol
3.1
Unicast Data Frame Forwarding
...
MVTX2600
When a frame arrives, it is assigned a handle in memory by the Frame Control Buffer Manager (FCB Manager). An
FCB handle will always be available because of advance buffer reservations.
The memory (SRAM) interface consists of two 64-bit buses, connected to two SRAM banks, A and B. The Receive
DMA (RxDMA) is responsible for multiplexing the data and the address. On a port’s “turn,” the RxDMA will move 8
bytes (or up to the end-of-frame) from the port’s associated RxFIFO into memory (Frame Data Buffer, or FDB).
Once an entire frame has been moved to the FDB, and a good end-of-frame (EOF) has been received, the Rx
interface makes a switch request. The RxDMA arbitrates among multiple switch requests.
The switch request consists of the first 64 bytes of a frame, containing among other things, the source and
destination MAC addresses of the frame. The search engine places a switch response in the switch response
queue of the frame engine when done. Among other information, the search engine will have resolved the
destination port of the frame and will have determined that the frame is unicast.
After processing the switch response, the Transmission Queue Manager (TxQ manager) of the frame engine is
responsible for notifying the destination port that it has a frame to forward to it. But first, the TxQ manager has to
decide whether or not to drop the frame, based on global FDB reservations and usage, as well as TxQ occupancy
at the destination. If the frame is not dropped, then the TxQ manager links the frame’s FCB to the correct per-portper-class TxQ. Unicast TxQ’s are linked lists of transmission jobs, represented by their associated frames’ FCB’s.
There is one linked list for each transmission class for each port. There are 4 transmission classes for each of the
24 10/100 ports and 8 classes for each of the two Gigabit ports – a total of 112 unicast queues.
The TxQ manager is responsible for scheduling transmission among the queues representing different classes for a
port. When the port control module determines that there is room in the MAC Transmission FIFO (TxFIFO) for
another frame, it requests the handle of a new frame from the TxQ manager. The TxQ manager chooses among
the head-of-line (HOL) frames from the per-class queues for that port using a Zarlink Semiconductor scheduling
algorithm.
22
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
The Transmission DMA (TxDMA) is responsible for multiplexing the data and the address. On a port’s turn, the
TxDMA will move 8 bytes (or up to the EOF) from memory into the port’s associated TxFIFO. After reading the EOF,
the port control requests a FCB release for that frame. The TxDMA arbitrates among multiple buffer release
requests.
The frame is transmitted from the TxFIFO to the line.
3.2
Multicast Data Frame Forwarding
After receiving the switch response, the TxQ manager has to make the dropping decision. A global decision to drop
can be made, based on global FDB utilization and reservations. If so, then the FCB is released and the frame is
dropped. In addition, a selective decision to drop can be made, based on the TxQ occupancy at some subset of
the multicast packet’s destinations. If so, then the frame is dropped at some destinations but not others and the
FCB is not released.
If the frame is not dropped at a particular destination port, then the TxQ manager formats an entry in the multicast
queue for that port and class. Multicast queues are physical queues (unlike the linked lists for unicast frames).
There are 2 multicast queues for each of the 24 10/100 ports. The queue with higher priority has room for 32 entries
and the queue with lower priority has room for 64 entries. There are 4 multicast queues for each of the two Gigabit
ports. The size of the queues are: 32 entries (higher priority queue), 32 entries, 32 entries and 64 entries (lower
priority queue). There is one multicast queue for every two priority classes. For the 10/100 ports to map the 8
transmit priorities into 2 multicast queues, the 2 LSB are discarded. For the gigabit ports to map the 8 transmit
priorities into 4 multicast queues, the LSB are discarded.
During scheduling, the TxQ manager treats the unicast queue and the multicast queue of the same class as one
logical queue. The older head of line of the two queues is forwarded first.
The port control requests a FCB release only after the EOF for the multicast frame has been read by all ports to
which the frame is destined.
3.3
Frame Forwarding To and From CPU
Frame forwarding from the CPU port to a regular transmission port is nearly the same as forwarding between
transmission ports. The only difference is that the physical destination port must be indicated in addition to the
destination MAC address.
Frame forwarding to the CPU port is nearly the same as forwarding to a regular transmission port. The only
difference is in frame scheduling. Instead of using the patent-pending Zarlink Semiconductor scheduling algorithms,
scheduling for the CPU port is simply based on strict priority. That is, a frame in a high priority queue will always be
transmitted before a frame in a lower priority queue. There are four output queues to the CPU and one receive
queue.
4.0
Memory Interface
4.1
Overview
The MVTX2604 provides two 64-bit wide SRAM banks, SRAM Bank A and SRAM Bank B with a 64-bit bus
connected to each. Each DMA can read and write from both bank A and bank B. The following figure provides an
overview of the MVTX2604 SRAM banks.
23
Zarlink Semiconductor Inc.
MVTX2604
SRAM
SRAM
TX DMA
0-7
Data Sheet
TX DMA
8-15
TX DMA
16-23
RX DMA
0-7
RX DMA
8-15
RX DMA
16-23
Figure 4 - MVTX2604 SRAM Interface Block Diagram (DMAs for 10/1000 Ports Only)
4.2
ZBT Support
The MVTX2604 supports Zero Bus Turnaround (ZBT). ZBT is a synchronous SRAM architecture that is optimized
for networking and telecommunications applications. It can significantly increase the switch’s internal bandwidth
when compared to standard Pipeline SyncBurst SRAM.
The ZBT architecture is optimized for switching and other applications with highly random READs and WRITEs.
ZBT SRAMs eliminate all idle cycles when turning the data bus around from a WRITE operation to a READ
operation (or vice versa). This feature results in dramatic performance improvements in systems that have such
traffic patterns (that is, frequent and random read and write access to the SRAM).
Please refer to the ZBT Application Note for further details.
4.3
Detailed Memory Information
Because the bus for each bank is 64 bits wide, frames are broken into 8-byte granules, written to and read from
memory. The first 8-byte granule gets written to Bank A, the second 8-byte granule gets written to Bank B and so on
in alternating fashion. When reading frames from memory, the same procedure is followed, first from A, then from B
and so on.
The reading and writing from alternating memory banks can be performed with minimal waste of memory
bandwidth. What’s the worst case? For any speed port, in the worst case, a 1-byte-long EOF granule gets written
to Bank A. This means that a 7-byte segment of Bank A bandwidth is idle, and furthermore, the next 8-byte
segment of Bank B bandwidth is idle, because the first 8 bytes of the next frame will be written to Bank A, not B.
This scenario results in a maximum 15 bytes of waste per frame, which is always acceptable because the
interframe gap is 20 bytes.
The CPU management port gets treated like any other port, reading and writing to alternating memory banks
starting with Bank A. The VLAN Index Mapping Table and Mac Address Table are duplicated in Bank A and B.
When the CPU writes an entry to the VLAN Index Mapping Table it has to write the same data in bank A and bank
B. Search engine data is written to both banks in parallel. In this way, a search engine read operation can be
performed by either bank at any time without a problem.
24
Zarlink Semiconductor Inc.
MVTX2604
4.4
Data Sheet
Memory Requirements
To speed up searching and decrease memory latency, the external MAC address database is duplicated in both
memory banks. To support 64 K MAC address, 4 MB memory is required. When VLAN support is enabled, 512
entries of the MAC address table are used for storing the VLAN ID at VLAN Index Mapping Table.
Up to 2 K Ethernet frame buffers are supported and they will use 3 MB of memory. Each frame uses 1536 bytes.
The maximum system memory requirement is 4 MB. If less memory is desired, the configuration can scale down.
Memory Configuration
Bank A
Bank B
Tag based VLAN
Frame Buffer
Max MAC Address
1M
1M
Disable
1K
32 K
1M
1M
Enable
1K
31.5 K
2M
2M
Disable
2K
64 K
2M
2M
Enable
2K
63.5 K
Memory Map
25
Zarlink Semiconductor Inc.
MVTX2604
5.0
Search Engine
5.1
Search Engine Overview
Data Sheet
The MVTX2604 search engine is optimized for high throughput searching, with enhanced features to support:
•
•
•
•
•
•
•
•
•
Up to 64 K MAC addresses
Up to 255 VLAN and IP Multicast groups
3 groups of port trunking (1 for the two Gigabit ports and 2 others)
Traffic classification into 4 (or 8 for Gigabit) transmission priorities and 2 drop precedence levels
Packet filtering
Security
IP Multicast
Flooding, Broadcast, Multicast Storm Control
MAC address learning and aging
5.2
Basic Flow
Shortly after a frame enters the MVTX2604 and is written to the Frame Data Buffer (FDB), the frame engine
generates a Switch Request, which is sent to the search engine. The switch request consists of the first 64 bytes of
the frame, which contain all the necessary information for the search engine to perform its task. When the search
engine is done, it writes to the Switch Response Queue and the frame engine uses the information provided in that
queue for scheduling and forwarding.
In performing its task, the search engine extracts and compresses the useful information from the 64-byte switch
request. Among the information extracted are the source and destination MAC addresses, the transmission and
discard priorities, whether the frame is unicast or multicast and VLAN ID. Requests are sent to the external SRAM
to locate the associated entries in the external hash table.
When all the information has been collected from external SRAM, the search engine has to compare the MAC
address on the current entry with the MAC address for which it is searching. If it is not a match, the process is
repeated on the internal MCT Table. All MCT entries other than the first of each linked list are maintained internal to
the chip. If the desired MAC address is still not found, then the result is either learning (source MAC address
unknown) or flooding (destination MAC address unknown).
In addition, VLAN information is used to select the correct set of destination ports for the frame (for multicast), or to
verify that the frame’s destination port is associated with the VLAN (for unicast).
If the destination MAC address belongs to a port trunk, then the trunk number is retrieved instead of the port
number. But on which port of the trunk will the frame be transmitted? This is easily computed using a hash of the
source and destination MAC addresses.
When all the information is compiled, the switch response is generated, as stated earlier. The search engine also
interacts with the CPU with regard to learning and aging.
5.3
5.3.1
Search, Learning, and Aging
MAC Search
The search block performs source MAC address and destination MAC address (or destination IP address for IP
multicast) searching. As we indicated earlier, if a match is not found, then the next entry in the linked list must be
examined and so on until a match is found or the end of the list is reached.
In tag based VLAN mode, if the frame is unicast, and the destination port is not a member of the correct VLAN, then
the frame is dropped; otherwise, the frame is forwarded. If the frame is multicast, this same table is used to indicate
26
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
all the ports to which the frame will be forwarded. Moreover, if port trunking is enabled, this block selects the
destination port (among those in the trunk group).
In port based VLAN mode, a bitmap is used to determine whether the frame should be forwarded to the outgoing
port. The main difference in this mode is that the bitmap is not dynamic. Ports cannot enter and exit groups
because of real-time learning made by a CPU.
The MAC search block is also responsible for updating the source MAC address timestamp and the VLAN port
association timestamp, used for aging.
5.3.2
Learning
The learning module learns new MAC addresses and performs port change operations on the MCT database. The
goal of learning is to update this database as the networking environment changes over time.
When CPU reporting is enabled, learning and port change will be performed when the CPU request queue has
room, and a memory slot is available, and a “Learn MAC Address” message is sent to the CPU. When fast learning
mode is enabled, learning and port change will be performed when memory slot is available and a latter “Learn
MAC Address” message is sent to the CPU when CPU queue has room.
When CPU reporting is disabled, learning and port change will be performed based on memory slot availability only.
In tag based VLAN mode, if the source port is not a member of a classified VLAN a “New VLAN Port” message is
sent to the CPU. The CPU can decide whether or not the source port can be added to the VLAN.
5.3.3
Aging
Aging time is controlled by register 400h and 401h.
The aging module scans and ages MCT entries based on a programmable “age out” time interval. As we indicated
earlier, the search module updates the source MAC address and VLAN port association timestamps for each frame
it processes. When an entry is ready to be aged, the entry is removed from the table and a “Delete MAC Address”
message is sent to inform the CPU.
Supported MAC entry types are: dynamic, static, source filter, destination filter, IP multicast, source and destination
filter and secure MAC address. Only dynamic entries can be aged; all others are static. The MAC entry type is
stored in the “status” field of the MCT data structure.
5.3.4
VLAN Table
The table below provides a mapping from VLAN ID to VLAN index. It is maintained by system software and is
checked by the hardware search engine for every incoming frame. This table has 4 K entries and is stored in
external SRAM. It is organized as 512 × 8 entries (total of 4 K VLAN indexes) as shown. Each VLAN index is 8 bits.
VIX7
VIX6
VIX5
VIX4
VIX3
VIX2
VIX1
VIX0
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
VIX4095
VIX4094
VIX4093
VIX4092
VIX4091
VIX4090
VIX4089
VIX4088
Table 1 - VLAN Index Mapping Table
Each VIX represents the mapping result from the associated VLAN ID (VLANID = 0x004 is mapped to VIX4).
Unused VLAN ID’s have their corresponding VIX programmed to hexadecimal 00. Used VLAN ID’s have their
corresponding VIX programmed to hexadecimal 01 through FF. In other words, 255 VLAN’s are supported. The VIX
value is a pointer to the entries in the VLAN Index port association table (internal memory).
27
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
The VLAN Index port association table is used by both software and hardware. It contains 256 entries. Each entry
has 27 fields, such that each field represents the port status of that particular VLAN.
Port
Not Used
G1
G0
CPU
P23
P22
Bit
63 to 54
53 52
51 50
49 48
47 46
45 44
……
P3
P2
P1
7 6
5 4
3
P0
2
1
0
0
E
N
T
R
I
E
S
1
:
:
255
Table 2 - LAN Index Port Association Table
Each entry has 64 bits. Each port has a VLAN status field with the following two bits values:
•
•
•
•
00: Port not a member of VLAN
01: Port is a member of VLAN, and is subject to aging (Do not use. Used by the aging module)
10: Port is a member of VLAN, and is subject to aging
11: Port is a member of VLAN, and is not subject to aging
Note: The VLAN aging time is controlled by register 402h.
5.4
MAC Address Filtering
The MVTX2604's implementation of intelligent traffic switching provides filters for source and destination MAC
addresses. This feature filters unnecessary traffic, thereby providing intelligent control over traffic flows and
broadcast traffic.
MAC address filtering allows the MVTX2604 to block an incoming packet to an interface when it sees a specified
MAC address in either the source address or destination address of the incoming packet. For example, if your
network is congested because of high utilization from a MAC address you can filter all traffic transmitted from that
address and restore network flow while you troubleshoot the problem.
5.5
Quality of Service
Quality of Service (QoS) refers to the ability of a network to provide better service to selected network traffic over
various technologies. Primary goals of QoS include dedicated bandwidth, controlled jitter and latency (required by
some real-time and interactive traffic) and improved loss characteristics.
Traditional Ethernet networks have had no prioritization of traffic. Without a protocol to prioritize or differentiate
traffic, a service level known as “best effort” attempts to get all the packets to their intended destinations with
minimum delay; however, there are no guarantees. In a congested network or when a low-performance
switch/router is overloaded, “best effort” becomes unsuitable for delay-sensitive traffic and mission-critical data
transmission.
28
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
The advent of QoS for packet-based systems accommodates the integration of delay-sensitive video and
multimedia traffic onto any existing Ethernet network. It also alleviates the congestion issues that have previously
plagued such “best effort” networking systems. QoS provides Ethernet networks with the breakthrough technology
to prioritize traffic and ensure that a certain transmission will have a guaranteed minimum amount of bandwidth.
Extensive core QoS mechanisms are built into the MVTX2604 architecture to ensure policy enforcement and
buffering of the ingress port, as well as weighted fair-queue(WFQ) scheduling at the egress port.
In the MVTX2604, QoS-based policies sort traffic into a small number of classes and mark the packets accordingly.
The QoS identifier provides specific treatment to traffic in different classes, so that different quality of service is
provided to each class. Frame and packet scheduling and discarding policies are determined by the class to which
the frames and packets belong. For example, the overall service given to frames and packets in the premium class
will be better than that given to the standard class; the premium class is expected to experience lower loss rate or
delay.
The MVTX2604 supports the following QoS techniques:
•
•
•
•
5.6
In a port-based setup, any station connected to the same physical port of the switch will have the same
transmit priority.
In a tag-based setup, a 3-bit field in the VLAN tag provides the priority of the packet. This priority can be
mapped to different queues in the switch to provide QoS.
In a TOS/DS-based set up, TOS stands for “Type of Service” that may include “minimize delay,” “maximize
throughput,” or “maximize reliability.” Network nodes may select routing paths or forwarding behaviours that
are suitably engineered to satisfy the service request.
In a logical port-based set up, a logical port provides the application information of the packet. Certain
applications are more sensitive to delays than others; using logical ports to classify packets can help speed
up delay sensitive applications, such as VoIP.
Priority Classification Rule
Figure 5 shows the MVTX2604 priority classification rule.
Yes
Use Default Port Settings
Fix Port Priority ?
No
TOS Precedence over VLAN?
(FCR Register, Bit 7)
Use Default Port Settings
No
No
No
IP
Yes
Yes
VLAN Tag ?
No
IP Frame ?
Yes
Yes
Use Logical Port
Yes
Use VLAN Priority
Use Logical Port
Figure 5 - Priority Classification Rule
29
Zarlink Semiconductor Inc.
No
Use TOS
MVTX2604
5.7
Data Sheet
Port and Tag Based VLAN
The MVTX2604 supports two models for determining and controlling how a packet gets assigned to a VLAN: port
priority and tag -based VLAN.
5.7.1
Port-Based VLAN
An administrator can use the PVMAP Registers to configure the MVTX2604 for port-based VLAN (see “Registration
Definition” on page 42). For example, ports 1-3 might be assigned to the Marketing VLAN, ports 4-6 to the
Engineering VLAN and ports 7-9 to the Administrative VLAN. The MVTX2604 determines the VLAN membership of
each packet by noting the port on which it arrives. From there, the MVTX2604 determines which outgoing port(s)
is/are eligible to transmit each packet or whether the packet should be discarded.
Destination Port Numbers Bit Map
Port Registers
26
Register for Port #0
PVMAP00_0[7:0] to PVMAP00_3[2:0]
…
2
1
0
0
1
1
0
Register for Port #1
PVMAP01_0[7:0] to PVMAP01_3[2:0]
0
1
0
1
Register for Port #2
PVMAP02_0[7:0] to PVMAP02_3[2:0]
0
0
0
0
0
0
0
0
…
Register for Port #26
PVMAP26_0[7:0] to PVMAP26_3[2:0]
Table 3 - PVMAP Register
For example, in the above table, a "1" denotes that an outgoing port is eligible to receive a packet from an incoming
port. A 0 (zero) denotes that an outgoing port is not eligible to receive a packet from an incoming port.
In this example:
Data packets received at port #0 are eligible to be sent to outgoing ports 1 and 2.
Data packets received at port #1 are eligible to be sent to outgoing ports 0 and 2.
Data packets received at port #2 are NOT eligible to be sent to ports 0 and 1.
5.7.2
Tag-Based VLAN
The MVTX2604 supports the IEEE 802.1q specification for “tagging” frames. The specification defines a way to
coordinate VLANs across multiple switches. In the specification, an additional 4-octet header (or “tag”) is inserted in
a frame after the source MAC address and before the frame type. 12 bits of the tag are used to define the VLAN ID.
Packets are then switched through the network with each MVTX2604 simply swapping the incoming tag for an
appropriate forwarding tag rather than processing each packet's contents to determine the path. This approach
minimizes the processing needed once the packet enters the tag-switched network. In addition, coordinating VLAN
IDs across multiple switches enables VLANs to extend to multiple switches.
Up to 255 VLANs are supported in the MVTX2604. The 4 K VLANs specified in the IEEE 802.1q are mapped to 255
VLAN indexes. The mapping is made by the VLAN index mapping table. Based on the VLAN index (VIXn), the
source and destination port membership is checked against the content in the VLAN Index Port association table. If
the destination port is a member of the VLAN, the packet is forwarded; otherwise it is discarded. If the source port is
not a member, a “New VLAN Port” message is sent to the CPU. A filter can be applied to discard the packet if the
source port is not a member of the VLAN.
30
Zarlink Semiconductor Inc.
MVTX2604
5.8
Data Sheet
Memory Configurations
The MVTX2604 supports the following memory configurations. Pipeline SBRAM modes support 1 M and 2 M per
bank configurations, while ZBT mode supports 4 M configurations, 2 M per domain (bank). For detail connection
information, please reference the memory application note.
Configuration
Single Layer
(Bootstrap pin
TSTOUT13 = open)
1 M per bank
(Bootstrap pin
TSTOUT7 = open)
2 M per bank
(Bootstrap pin
TSTOUT7 = pull down)
Connections
Two 128 K x 32 SRAM/bank
Two 256 K x 32 SRAM/bank
Connect 0E# and WE#
Four 128 K x 32
SRAM/bank
Connect 0E0# and
WE0#
Connect 0E1# and
WE1#
or
One 128 K x 64 SRAM/bank
NA
Double Layer
(Bootstrap pin
TSTOUT13 = pull
down)
or
Two 128 K x 64 SRAM/bank
Table 4 - Supported Memory Configurations (SBRAM Mode)
Configuration
2 M per bank
Connections
Single Layer
(Bootstrap pin
TSTOUT13 = open)
Two 256 K x 32 ZBT SRAM/bank
or One 256 K x 64 ZBT SRAM/bank
Connect ADS# to Layer 0 chipselect
pin
Double Layer
(Bootstrap pin
TSTOUT13 = pull down)
Four 128 K x 32 ZBT SRAM/bank
or Two 128 K x 64 ZBT SRAM/bank
Connect ADS# to Layer 0 chipselect
pin
and 0E# to Layer 1 chipselect pin
Table 5 - Supported Memory Configurations (ZBT Mode)
Frame data Buffer
Only Bank A
1M
(SBRAM)
2M
(SBRAM)
MVTX2601
X
X
MVTX2602
X
X
MVTX2603
Bank A and Bank B
Bank A and Bank B
1 M/bank
(SBRAM)
2 M/bank
(SBRAM)
1 M/bank
(ZBT SRAM)
2 M/bank
(ZBT SRAM)
X
X
X
X
X
X
MVTX2603
(Gigabit ports
in 2giga mode)
MVTX2604
X
X
MVTX2604
(Gigabit ports
in 2giga mode)
Table 6 - Options for Memory Configuration
31
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
Bank A (1 M One Layer)
Bank B (1 M One Layer)
Data LA_D[63:32]
Data LB_D[63:32]
Data LB_D[31:0]
Data LA_D[31:0]
SRAM
Memory
128 K
32 bits
SRAM
Memory
128 K
32 bits
Memory
128 K
32 bits
Memory
128 K
32 bits
Address LB_A[19:3]
Address LA_A[19:3]
Bootstraps: TSTOUT7 = Open, TSTOUT13 = Open, TSTOUT4 = Open
Figure 6 - Memory Configuration For: 2 Banks, 1 Layer, 2 MB Total
Bank A (2 M Two Layers)
Bank B (2 M Two Layers)
Data LA_D[63:32]
Data LB_D[63:32]
Data LA_D[31:0]
Data LB_D[31:0]
SRAM
Memory
128 K
32 bits
SRAM
Memory
128 K
32 bits
SRAM
Memory
128 K
32 bits
SRAM
Memory
128 K
32 bits
Address LA_A[19:3]
SRAM
Memory
128 K
32 bits
SRAM
Memory
128 K
32 bits
SRAM
Memory
128 K
32 bits
SRAM
Memory
128 K
32 bits
Address LB_A[19:3]
Bootstraps: TSTOUT7 = Pull Down, TSTOUT13 = Pull Down, TSTOUT4 = Open
Figure 7 - Memory Configuration For: 2 Banks, 2 Layers, 4 MB Total
32
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
Bank A (2 M One Layer)
Bank B (2 M One Layer)
Data LA_D[63:32]
Data LB_D[63:32]
Data LB_D[31:0]
Data LA_D[31:0]
SRAM
Memory
256 K
32 bits
SRAM
Memory
256 K
32 bits
Memory
256 K
32 bits
Memory
256 K
32 bits
Address LB_A[20:3]
Address LA_A[20:3]
Bootstraps: TSTOUT7 = Pull Down, TSTOUT13 = Open, TSTOUT4 = Open
Figure 8 - Memory Configuration For: 2 Banks, 1 Layer, 4 MB
Bank A (2 M Two Layers)
Bank B (2 M Two Layers)
Data LA_D[63:32]
Data LB_D[63:32]
Data LA_D[31:0]
Data LB_D[31:0]
ZBT
Memory
128 K
32 bits
ZBT
Memory
128 K
32 bits
ZBT
Memory
128 K
32 bits
ZBT
Memory
128 K
32 bits
Address LA_A[19:3]
ZBT
Memory
128 K
32 bits
ZBT
Memory
128 K
32 bits
ZBT
Memory
128 K
32 bits
ZBT
Memory
128 K
32 bits
Address LB_A[19:3]
Bootstraps: TSTOUT7 = Pull Down, TSTOUT13 = Pull Down, TSTOUT4 = Open
Figure 9 - Memory Configuration For: 2 Banks, 2 Layers, 4 MB Total
33
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
Bank A (2 M One Layer)
Bank B (2 M One Layer)
Data LA_D[63:32]
Data LB_D[63:32]
Data LA_D[31:0]
ZBT
Memory
256 K
32 bits
Data LB_D[31:0]
ZBT
Memory
256 K
32 bits
ZBT
Memory
256 K
32 bits
ZBT
Memory
256 K
32 bits
Address LB_A[20:3]
Address LA_A[20:3]
Bootstraps: TSTOUT7 = Pull Down, TSTOUT13 = Open, TSTOUT4 = Open
Figure 10 - Memory Configuration For: 2 Banks, 1 Layer, 4 MB
6.0
Frame Engine
6.1
Data Forwarding Summary
When a frame enters the device at the RxMAC, the RxDMA will move the data from the MAC RxFIFO to the FDB.
Data is moved in 8-byte granules in conjunction with the scheme for the SRAM interface.
A switch request is sent to the Search Engine. The Search Engine processes the switch request.
A switch response is sent back to the Frame Engine and indicates whether the frame is unicast or multicast and its
destination port or ports. A VLAN table lookup is performed as well.
A Transmission Scheduling Request is sent in the form of a signal notifying the TxQ manager. Upon receiving a
Transmission Scheduling Request, the device will format an entry in the appropriate Transmission Scheduling
Queue (TxSch Q) or Queues. There are 4 TxSch Q for each 10/100 port (and 8 per Gigabit port), one for each
priority. Creation of a queue entry either involves linking a new job to the appropriate linked list if unicast or adding
an entry to a physical queue if multicast.
When the port is ready to accept the next frame, the TxQ manager will get the head-of-line (HOL) entry of one of
the TxSch Qs, according to the transmission scheduling algorithm (to ensure per-class quality of service). The
unicast linked list and the multicast queue for the same port-class pair are treated as one logical queue. The older
HOL between the two queues goes first. For 10/100 ports multicast queue 0 is associated with unicast queue 0 and
multicast queue 1 is associated with unicast queue 2. For Gigabit ports multicast queue 0 is associated with unicast
queue 0, multicast queue 1 with unicast queue 2, multicast queue 2 with unicast queue 4 and multicast queue 3
with unicast queue 6.
The TxDMA will pull frame data from the memory and forward it granule-by-granule to the MAC TxFIFO of the
destination port.
34
Zarlink Semiconductor Inc.
MVTX2604
6.2
Data Sheet
Frame Engine Details
This section briefly describes the functions of each of the modules of the MVTX2604 frame engine.
6.2.1
FCB Manager
The FCB manager allocates FCB handles to incoming frames and releases FCB handles upon frame departure.
The FCB manager is also responsible for enforcing buffer reservations and limits. The default values can be
determined by referring to Chapter 7. In addition, the FCB manager is responsible for buffer aging and for linking
unicast forwarding jobs to their correct TxSch Q. The buffer aging can be enabled or disabled by the bootstrap pin
and the aging time is defined in register FCBAT.
6.2.2
Rx Interface
The Rx interface is mainly responsible for communicating with the RxMAC. It keeps track of the start and end of
frame and frame status (good or bad). Upon receiving an end of frame that is good, the Rx interface makes a switch
request.
6.2.3
RxDMA
The RxDMA arbitrates among switch requests from each Rx interface. It also buffers the first 64 bytes of each
frame for use by the search engine when the switch request has been made.
6.2.4
TxQ Manager
First, the TxQ manager checks the per-class queue status and global reserved resource situation and using this
information makes the frame dropping decision after receiving a switch response. If the decision is not to drop, the
TxQ manager requests that the FCB manager link the unicast frame’s FCB to the correct per-port-per-class TxQ. If
multicast, the TxQ manager writes to the multicast queue for that port and class. The TxQ manager can also trigger
source port flow control for the incoming frame’s source if that port is flow control enabled. Second, the TxQ
manager handles transmission scheduling; it schedules transmission among the queues representing different
classes for a port. Once a frame has been scheduled, the TxQ manager reads the FCB information and writes to
the correct port control module.
6.3
Port Control
The port control module calculates the SRAM read address for the frame currently being transmitted. It also writes
start of frame information and an end of frame flag to the MAC TxFIFO. When transmission is done, the port control
module requests that the buffer be released.
6.4
TxDMA
The TxDMA multiplexes data and address from port control and arbitrates among buffer release requests from the
port control modules.
7.0
Quality of Service and Flow Control
7.1
Model
Quality of service is an all-encompassing term for which different people have different interpretations. In general,
the approach to quality of service described here assumes that we do not know the offered traffic pattern. We also
assume that the incoming traffic is not policed or shaped. Furthermore, we assume that the network manager
knows his applications, such as voice, file transfer, or web browsing and their relative importance. The manager
can then subdivide the applications into classes and set up a service contract with each. The contract may consist
35
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
of bandwidth or latency assurances per class. Sometimes it may even reflect an estimate of the traffic mix offered to
the switch. As an added bonus, although we do not assume anything about the arrival pattern, if the incoming traffic
is policed or shaped we may be able to provide additional assurances about our switch’s performance.
Table 7 shows examples of QoS applications with three transmission priorities, but best effort (P0) traffic may form
a fourth class with no bandwidth or latency assurances. Gigabit ports actually have eight total transmission
priorities.
Goals
TotalAssured
Bandwidth (user
defined)
Low Drop Probability
(low-drop)
High Drop Probability
(high-drop)
Highest transmission
priority, P3
50 Mbps
Apps: phone calls,
circuit emulation.
Latency: < 1 ms.
Drop: No drop if P3 not
oversubscribed.
Apps: training video.
Latency: < 1 ms.
Drop: No drop if P3 not
oversubscribed; first P3 to drop
otherwise.
Middle transmission
priority, P2
37.5 Mbps
Apps: interactive apps,
Web business.
Latency: < 4-5 ms.
Drop: No drop if P2 not
oversubscribed.
Apps: non-critical interactive
apps.
Latency: < 4-5 ms.
Drop: No drop if P2 not
oversubscribed; firstP2 to drop
otherwise.
Low transmission
priority, P1
12.5 Mbps
Apps: emails, file
backups.
Latency: < 16 ms
desired, but not critical.
Drop: No drop if P1 not
oversubscribed.
Apps: casual web browsing.
Latency: < 16 ms desired, but
not critical.
Drop: No drop if P1 not
oversubscribed; first to drop
otherwise.
Total
100 Mbps
Table 7 - Two-dimensional World Traffic
A class is capable of offering traffic that exceeds the contracted bandwidth. A well-behaved class offers traffic at a
rate no greater than the agreed-upon rate. By contrast, a misbehaving class offers traffic that exceeds the agreedupon rate. A misbehaving class is formed from an aggregation of misbehaving microflows. To achieve high link
utilization, a misbehaving class is allowed to use any idle bandwidth. However, such leniency must not degrade the
quality of service (QoS) received by well-behaved classes.
As Table 7 illustrates, the six traffic types may each have their own distinct properties and applications. As shown,
classes may receive bandwidth assurances or latency bounds. In the table, P3, the highest transmission class,
requires that all frames be transmitted within 1 ms,and receives 50% of the 100 Mbps of bandwidth at that port.
Best-effort (P0) traffic forms a fourth class that only receives bandwidth when none of the other classes have any
traffic to offer. It is also possible to add a fourth class that has strict priority over the other three; if this class has
even one frame to transmit, then it goes first. In the MVTX2604, each 10/100 Mbps port will support four total
classes and each 1000 Mbps port will support eight classes. We will discuss the various modes of scheduling these
classes in the next section.
In addition, each transmission class has two subclasses, high-drop and low-drop. Well-behaved users should rarely
lose packets. But poorly behaved users – users who send frames at too high a rate – will encounter frame loss and
the first to be discarded will be high-drop. Of course, if this is insufficient to resolve the congestion, eventually some
low-drop frames are dropped and then all frames in the worst case.
36
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
Table 7 shows that different types of applications may be placed in different boxes in the traffic table. For example,
casual web browsing fits into the category of high-loss, high-latency-tolerant traffic, whereas VoIP fits into the
category of low-loss, low-latency traffic.
7.2
Four QoS Configurations
There are four basic pieces to QoS scheduling in the MVTX2604: strict priority (SP), delay bound, weighted fair
queuing (WFQ), and best effort (BE). Using these four pieces, there are four different modes of operation as shown
in the tables below. For 10/100 Mbps ports, the following registers select these modes:
QOSC24 [7:6]_CREDIT_C00
QOSC28 [7:6]_CREDIT_C10
QOSC32 [7:6]_CREDIT_C20
QOSC36 [7:6]_CREDIT_C30
P3
P2
P1
Op1 (default)
Delay Bound
Op2
SP
Delay Bound
Op3
SP
WFQ
Op4
WFQ
P0
BE
BE
Table 8 - Four QoS Configurations for a 10/100 Mbps Port
QOSC40 [7:6] and QOSC48 [7:6] select these modes for the first and second gigabit ports, respectively.
P7
P6
P5
P4
Op1 (default)
Delay Bound
Op2
SP
Delay Bound
Op3
SP
WFQ
Op4
WFQ
P3
P2
P1
P0
BE
BE
Table 9 - Four QoS Configurations for a Gigabit Port
The default configuration for a 10/100 Mbps port is three delay-bounded queues and one best-effort queue. The
delay bounds per class are 0,8 ms for P3, 3.2 ms for P2, and 12.8 ms for P1. For a 1 Gbps port, we have a default
of six delay-bounded queues and two best-effort queues. The delay bounds for a 1 Gbps port are 0.16 ms for P7
and P6, 0.32 ms for P5, 0.64 ms for P4, 1.28 ms for P3, and 2.56 ms for P2. Best effort traffic is only served when
there is no delay-bounded traffic to be served. For a 1 Gbps port, where there are two best-effort queues, P1 has
strict priority over P0.
We have a second configuration for a 10/100 Mbps port in which there is one strict priority queue, two delay
bounded queues and one best effort queue. The delay bounds per class are 3.2 ms for P2 and 12.8 ms for P1. If
the user is to choose this configuration, it is important that P3 (SP) traffic be either policed or implicitly bounded
(e.g., if the incoming P3 traffic is very light and predictably patterned). Strict priority traffic, if not admissioncontrolled at a prior stage to the MVTX2604 can have an adverse effect on all other classes’ performance. For a
1 Gbps port, P7 and P6 are both SP classes and P7 has strict priority over P6. In this case, the delay bounds per
class are 0.32 ms for P5, 0.64 ms for P4, 1.28 ms for P3, and 2.56 ms for P2.
37
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
The third configuration for a 10/100 Mbps port contains one strict priority queue and three queues receiving a
bandwidth partition via WFQ. As in the second configuration, strict priority traffic needs to be carefully controlled. In
the fourth configuration, all queues are served using a WFQ service discipline.
7.3
Delay Bound
In the absence of a sophisticated QoS server and signaling protocol, the MVTX2604 may not know the mix of
incoming traffic ahead of time. To cope with this uncertainty, our delay assurance algorithm dynamically adjusts its
scheduling and dropping criteria, guided by the queue occupancies and the due dates of their head-of-line (HOL)
frames. As a result, we assure latency bounds for all admitted frames with high confidence, even in the presence of
system-wide congestion. Our algorithm identifies misbehaving classes and intelligently discards frames at no
detriment to well-behaved classes. Our algorithm also differentiates between high-drop and low-drop traffic with a
weighted random early drop (WRED) approach. Random early dropping prevents congestion by randomly dropping
a percentage of high-drop frames even before the chip’s buffers are completely full, while still largely sparing lowdrop frames. This allows high-drop frames to be discarded early, as a sacrifice for future low-drop frames. Finally,
the delay bound algorithm also achieves bandwidth partitioning among classes.
7.4
Strict Priority and Best Effort
When strict priority is part of the scheduling algorithm, if a queue has even one frame to transmit, it goes first. Two
of our four QoS configurations include strict priority queues. The goal is for strict priority classes to be used for IETF
expedited forwarding (EF), where performance guarantees are required. As we have indicated, it is important that
strict priority traffic be either policed or implicitly bounded, so as to keep from harming other traffic classes.
When best effort is part of the scheduling algorithm, a queue only receives bandwidth when none of the other
classes have any traffic to offer. Two of our four QoS configurations include best effort queues. The goal is for best
effort classes to be used for non-essential traffic, because we provide no assurances about best effort performance.
However, in a typical network setting, much best effort traffic will indeed be transmitted and with an adequate
degree of expediency.
Because we do not provide any delay assurances for best effort traffic, we do not enforce latency by dropping best
effort traffic. Furthermore, because we assume that strict priority traffic is carefully controlled before entering the
MVTX2604, we do not enforce a fair bandwidth partition by dropping strict priority traffic. To summarize, dropping to
enforce bandwidth or delay does not apply to strict priority or best effort queues. We only drop frames from best
effort and strict priority queues when global buffer resources become scarce.
7.5
Weighted Fair Queuing
In some environments – for example, in an environment in which delay assurances are not required, but precise
bandwidth partitioning on small time scales is essential, WFQ may be preferable to a delay-bounded scheduling
discipline. The MVTX2604 provides the user with a WFQ option with the understanding that delay assurances can
not be provided if the incoming traffic pattern is uncontrolled. The user sets four WFQ “weights” (eight for Gigabit
ports) such that all weights are whole numbers and sum to 64. This provides per-class bandwidth partitioning with
error within 2%.
In WFQ mode, though we do not assure frame latency, the MVTX2604 still retains a set of dropping rules that helps
to prevent congestion and trigger higher level protocol end-to-end flow control.
As before, when strict priority is combined with WFQ, we do not have special dropping rules for the strict priority
queues, because the input traffic pattern is assumed to be carefully controlled at a prior stage. However, we do
indeed drop frames from SP queues for global buffer management purposes. In addition, queue P0 for a 10/100
port (and queues P0 and P1 for a Gigabit port) are treated as best effort from a dropping perspective, though they
still are assured a percentage of bandwidth from a WFQ scheduling perspective. What this means is that these
particular queues are only affected by dropping when the global buffer count becomes low.
38
Zarlink Semiconductor Inc.
MVTX2604
7.6
Data Sheet
Shaper
Although traffic shaping is not a primary function of the MVTX2604, the chip does implement a shaper for expedited
forwarding (EF). Our goal in shaping is to control the peak and average rate of traffic exiting the MVTX2604.
Shaping is limited to the two Gigabit ports only, and only to class P6 (the second highest priority). This means that
class P6 will be the class used for EF traffic. If shaping is enabled for P6, then P6 traffic must be scheduled using
strict priority. With reference to Table 7, only the middle two QoS configurations may be used.
Peak rate is set using a programmable whole number, no greater than 64. For example, if the setting is 32, then the
peak rate for shaped traffic is 32/64 * 1000 Mbps = 500 Mbps. Average rate is also a programmable whole number,
no greater than 64 and no greater than the peak rate. For example, if the setting is 16, then the average rate for
shaped traffic is 16/64 * 1000 Mbps = 250 Mbps. As a consequence of the above settings in our example, shaped
traffic will exit the MVTX2604 at a rate always less than 500 Mbps and averaging no greater than 250 Mbps. See
Programming QoS Register application note for more information.
Also, when shaping is enabled, it is possible for a P6 queue to explode in length if fed by a greedy source. The
reason is that a shaper is by definition not work-conserving; that is, it may hold back from sending a packet even if
the line is idle. Though we do have global resource management, we do nothing to prevent this situation locally. We
assume SP traffic is policed at a prior stage to the MVTX2604.
7.7
Rate Control
The MVTX2604 provides a rate control function on its 10/100 ports. This rate control function applies to the
outgoing traffic aggregate on each 10/100 port. It provides a way of reducing the outgoing average rate below full
wire speed. Note that the rate control function does not shape or manipulate any particular traffic class.
Furthermore, though the average rate of the port can be controlled with this function, the peak rate will still be full
line rate.
Two principal parameters are used to control the average rate for a 10/100 port. A port’s rate is controlled by
allowing, on average, M bytes to be transmitted every N microseconds. Both of these values are programmable.
The user can program the number of bytes in 8-byte increments and the time may be set in units of 10 ms.
The value of M/N will, of course, equal the average data rate of the outgoing traffic aggregate on the given 10/100
port. Although there are many (M,N) pairs that will provide the same average data rate performance, the smaller the
time interval N, the “smoother” the output pattern will appear.
In addition to controlling the average data rate on a 10/100 port, the rate control function also manages the
maximum burst size at wire speed. The maximum burst size can be considered the memory of the rate control
mechanism; if the line has been idle for a long time, to what extent can the port “make up for lost time” by
transmitting a large burst? This value is also programmable, measured in 8-byte increments.
Example: Suppose that the user wants to restrict Fast Ethernet port P’s average departure rate to 32 Mbps – 32%
of line rate – when the average is taken over a period of 10 ms. In an interval of 10 ms, exactly 40000 bytes can be
transmitted at an average rate of 32 Mbps.
So how do we set the parameters? The rate control parameters are contained in an internal RAM block accessible
through the CPU port (See Programming QoS Registers application note and Processor interface application note).
The data format is shown below.
63:40
39:32
31:16
15:0
0
Time interval
Maximum burst size
Number of bytes
As we indicated earlier, the number of bytes is measured in 8-byte increments, so the 16-bit field “Number of bytes”
should be set to 40000/8, or 5000. In addition, the time interval has to be indicated in units of 10 ms. Though we
want the average data rate on port P to be 32 Mbps when measured over an interval of 10 ms, we can also adjust
the maximum number of bytes that can be transmitted at full line rate in any single burst. Suppose we wish this limit
39
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
to be 12 kilobytes. The number of bytes is measured in 8-byte increments, so the 16-bit field “Maximum burst size”
is set to 12000/8, or 1500.
7.8
WRED Drop Threshold Management Support
To avoid congestion, the Weighted Random Early Detection (WRED) logic drops packets according to specified
parameters. The following table summarizes the behavior of the WRED logic.
In KB (kilobytes)
Level 1
N ≥ 120
Level 2
N ≥ 140
P3
P3 ≥ AKB
P2
P1
P2 ≥ BKB
P1 ≥ CKB
Level 3
N ≥ 160
High Drop
Low Drop
X%
0%
Y%
Z%
100%
100%
Table 10 - WRED Drop Thresholds
Px is the total byte count, in the priority queue x. The WRED logic has three drop levels, depending on the value of
N, which is based on the number of bytes in the priority queues. If delay bound scheduling is used, N equals
P3*16+P2*4+P1. If using WFQ scheduling, N equals P3+P2+P1. Each drop level from one to three has defined
high-drop and low-drop percentages, which indicate the minimum and maximum percentages of the data that can
be discarded. The X, Y Z percent can be programmed by the register RDRC0, RDRC1. In Level 3, all packets are
dropped if the bytes in each priority queue exceed the threshold. Parameters A, B, C are the byte count thresholds
for each priority queue. They can be programmed by the QOS control register (refer to the register group 5). See
Programming QoS Registers application note for more information.
7.9
Buffer Management
Because the number of FDB slots is a scarce resource and because we want to ensure that one misbehaving
source port or class cannot harm the performance of a well-behaved source port or class, we introduce the concept
of buffer management into the MVTX2604. Our buffer management scheme is designed to divide the total buffer
space into numerous reserved regions and one shared pool as shown in Figure 11 on page 41.
As shown in the figure, the FDB pool is divided into several parts. A reserved region for temporary frames stores
frames prior to receiving a switch response. Such a temporary region is necessary, because when the frame first
enters the MVTX2604, its destination port and class are as yet unknown, and so the decision to drop or not needs
to be temporarily postponed. This ensures that every frame can be received first before subjecting them to the
frame drop discipline after classifying.
Six reserved sections, one for each of the first six priority classes, ensure a programmable number of FDB slots per
class. The lowest two classes do not receive any buffer reservation. Furthermore, even for 10/100 Mbps ports, a
frame is stored in the region of the FDB corresponding to its class. As we have indicated, the eight classes use only
four transmission scheduling queues for 10/100 Mbps ports, but as far as buffer usage is concerned there are still
eight distinguishable classes.
Another segment of the FDB reserves space for each of the 27 ports — 26 ports for Ethernet and one CPU port
(port number 24). Two parameters can be set, one for the source port reservation for 10/100 Mbps ports and CPU
port, and one for the source port reservation for 1 Gbps ports. These 27 reserved regions make sure that no wellbehaved source port can be blocked by another misbehaving source port.
In addition, there is a shared pool, which can store any type of frame. The frame engine allocates the frames first in
the six priority sections. When the priority section is full or the packet has priority 1 or 0, the frame is allocated in the
shared poll. Once the shared poll is full the frames are allocated in the section reserved for the source port.
40
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
The following registers define the size of each section of the Frame data Buffer:
PR100- Port Reservation for 10/100 Ports
PRG- Port Reservation for Giga Ports
SFCB- Share FCB Size
C2RS- Class 2 Reserve Size
C3RS- Class 3 Reserve Size
C4RS- Class 4 Reserve Size
C5RS- Class 5 Reserve Size
C6RS- Class 6 Reserve Size
C7RS- Class 7 Reserve Size
temporary
reservation
shared pool
S
per-class
reservation
per-source
reservations
(24 10/100 M, CPU)
per-source
reservations
(2 G)
Figure 11 - Buffer Partition Scheme Used to Implement MVTX2604 AG Buffer Management
7.9.1
Dropping When Buffers Are Scarce
Summarizing the two examples of local dropping discussed earlier in this chapter:
If a queue is a delay-bounded queue we have a multi-level WRED drop scheme designed to control delay and
partition bandwidth in case of congestion.
If a queue is a WFQ-scheduled queue we have a multi-level WRED drop scheme designed to prevent congestion.
In addition to these reasons for dropping, we also drop frames when global buffer space becomes scarce. The
function of buffer management is to make sure that such dropping causes as little blocking as possible.
41
Zarlink Semiconductor Inc.
MVTX2604
7.10
Data Sheet
MVTX2604 Flow Control Basics
Because frame loss is unacceptable for some applications, the MVTX2604 provides a flow control option. When
flow control is enabled, scarcity of buffer space in the switch may trigger a flow control signal; this signal tells a
source port that is sending a packet to this switch, to temporarily hold off.
While flow control offers the clear benefit of no packet loss, it also introduces a problem for quality of service. When
a source port receives an Ethernet flow control signal, all microflows originating at that port, well-behaved or not,
are halted. A single packet destined for a congested output can block other packets destined for uncongested
outputs. The resulting head-of-line blocking phenomenon means that quality of service cannot be assured with high
confidence when flow control is enabled.
In the MVTX2604, each source port can independently have flow control enabled or disabled. For flow control
enabled ports, by default all frames are treated as lowest priority during transmission scheduling. This is done so
that those frames are not exposed to the WRED Dropping scheme. Frames from flow control enabled ports feed to
only one queue at the destination, the queue of lowest priority. This means that if flow control is enabled for a given
source port then we can guarantee that no packets originating from that port will be lost but at the possible expense
of minimum bandwidth or maximum delay assurances. In addition, these “downgraded” frames may only use the
shared pool or the per-source reserved pool in the FDB; frames from flow control enabled sources may not use
reserved FDB slots for the highest six classes (P2-P7).
The MVTX2604 does provide a system-wide option of permitting normal QoS scheduling (and buffer use) for
frames originating from flow control enabled ports. When this programmable option is active, it is possible that
some packets may be dropped even though flow control is on. The reason is that intelligent packet dropping is a
major component of the MVTX2604’s approach to ensuring bounded delay and minimum bandwidth for high priority
flows.
7.10.1
Unicast Flow Control
For unicast frames, flow control is triggered by source port resource availability. Recall that the MVTX2604’s buffer
management scheme allocates a reserved number of FDB slots for each source port. If a programmed number of a
source port’s reserved FDB slots have been used then flow control Xoff is triggered.
Xon is triggered when a port is currently being flow controlled and all of that port’s reserved FDB slots have been
released.
Note that the MVTX2604’s per-source-port FDB reservations assure that a source port that sends a single frame to
a congested destination will not be flow controlled.
7.10.2
Multicast Flow Control
In unmanaged mode, flow control for multicast frames is triggered by a global buffer counter. When the system
exceeds a programmable threshold of multicast packets Xoff is triggered. Xon is triggered when the system returns
below this threshold.
In managed mode, per-VLAN flow control is used for multicast frames. In this case, flow control is triggered by
congestion at the destination. How so? The MVTX2604 checks each destination to which a multicast packet is
headed. For each destination port, the occupancy of the lowest-priority transmission multicast queue (measured in
number of frames) is compared against a programmable congestion threshold. If congestion is detected at even
one of the packet’s destinations then Xoff is triggered.
In addition, each source port has a 26-bit port map recording which port or ports of the multicast frame’s fanout
were congested at the time Xoff was triggered. All ports are continuously monitored for congestion and a port is
identified as uncongested when its queue occupancy falls below a fixed threshold. When all those ports that were
originally marked as congested in the port map have become uncongested, then Xon is triggered and the 26-bit
vector is reset to zero.
42
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
The MVTX2604 also provides the option of disabling VLAN multicast flow control.
Note: If per-Port flow control is on, QoS performance will be affected.
7.11
Mapping to IETF Diffserv Classes
The mapping between priority classes discussed in this chapter and elsewhere is shown below.
VTX
P7
P6
P5
P4
P3
P2
P1
P0
IETF
NM
EF
AF0
AF1
AF2
AF3
BE0
BE1
Table 11 - Mapping between MVTX2604 and IETF Diffserv Classes for Gigabit Ports
As the table illustrates, P7 is used solely for network management (NM) frames. P6 is used for expedited
forwarding service (EF). Classes P2 through P5 correspond to an assured forwarding (AF) group of size 4. Finally,
P0 and P1 are two best effort (BE) classes.
For 10/100 Mbps ports, the classes of Table 12 are merged in pairs—one class corresponding to NM+EF, two AF
classes, and a single BE class.
VTX
P3
P2
P1
P0
IETF
NM+EF
AF0
AF1
BE0
Table 12 - Mapping between MVTX2604 and IETF Diffserv Classes for 10/100 Ports
Features of the MVTX2604 that correspond to the requirements of their associated IETF classes are summarized in
the table below.
Network management (NM) and
Expedited forwarding (EF)
Global buffer reservation for NM and EF
Shaper for EF traffic on 1 Gbps ports
Option of strict priority scheduling
No dropping if admission controlled
Assured forwarding (AF)
Four AF classes for 1 Gbps ports
Programmable bandwidth partition, with option of
WFQ service
Option of delay-bounded service keeps delay
under fixed levels even if not admissioncontrolled
Random early discard, with programmable levels
Global buffer reservation for each AF class
Best effort (BE)
Two BE classes for 1 Gbps ports
Service only when other queues are idle means
that QoS not adversely affected
Random early discard, with programmable levels
Traffic from flow control enabled ports
automatically classified as BE
Table 13 - MVTX2604 Features Enabling IETF Diffserv Standards
43
Zarlink Semiconductor Inc.
MVTX2604
8.0
Port Trunking
8.1
Features and Restrictions
Data Sheet
A port group (i.e., trunk) can include up to 4 physical ports but when using stack all of the ports in a group must be
in the same MVTX2604.
The two Gigabit ports may also be trunked together. There are three trunk groups total including the option to trunk
Gigabit ports.
Load distribution among the ports in a trunk for unicast is performed using hashing based on source MAC address
and destination MAC address. Three other options include source MAC address only, destination MAC address
only and source port (in bidirectional ring mode only). Load distribution for multicast is performed similarly.
If a VLAN includes any of the ports in a trunk group, all the ports in that trunk group should be in the same VLAN
member map.
The MVTX2604 also provides a safe fail-over mode for port trunking automatically. If one of the ports in the trunking
group goes down, the MVTX2604 will automatically redistribute the traffic over to the remaining ports in the trunk in
unmanaged mode. In managed mode, the software can perform similar tasks.
8.2
Unicast Packet Forwarding
The search engine finds the destination MCT entry, and if the status field says that the destination port found
belongs to a trunk, then the group number is retrieved instead of the port number. In addition, if the source address
belongs to a trunk then the source port’s trunk membership register is checked.
A hash key, based on some combination of the source and destination MAC addresses for the current packet
selects the appropriate forwarding port as specified in the Trunk_Hash registers.
8.3
Multicast Packet Forwarding
For multicast packet forwarding, the device must determine the proper set of ports from which to transmit the
packet based on the VLAN index and hash key.
Two functions are required in order to distribute multicast packets to the appropriate destination ports in a port
trunking environment.
Determining one forwarding port per group. For multicast packets, all but one port per group, the forwarding port
must be excluded.
Preventing the multicast packet from looping back to the source trunk.
The search engine needs to prevent a multicast packet from sending to a port that is in the same trunk group with
the source port. This is because, when we select the primary forwarding port for each group we do not take the
source port into account. To prevent this, we simply apply one additional filter so as to block that forwarding port for
this multicast packet.
44
Zarlink Semiconductor Inc.
MVTX2604
8.4
Data Sheet
Unmanaged Trunking
In unmanaged mode, 3 trunk groups are supported. Groups 0 and 1 can trunk up to 4 10/100 ports. Group 2 can
trunk 2 Gigabit ports. The supported combinations are shown in the following table.
Group 0
Port 0
Port 1
Port 2
9
9
9
9
9
9
9
9
Port 3
9
Select via trunk0_mode register
Group 1
Port 4
Port 5
9
9
9
9
Port 6
Port 7
9
9
Select via trunk1_mode register
Group 2
Port 25(Giga 0)
Port 26 (Giga 1)
9
9
In unmanaged mode, the trunks are individually enabled/disabled by controlling pin trunk0,1,2.
9.0
9.1
Port Mirroring
Port Mirroring Features
The received or transmitted data of any 10/100 port in the MVTX2604 chip can be “mirrored” to any other port. We
support two such mirrored source-destination pairs. A mirror port can not also serve as a data port.
Please refer to the Port Mirroring Application note for further details.
9.2
Setting Registers for Port Mirroring
MIRROR1_SRC: Sets the source port for the first port mirroring pair. Bits [4:0] select the source port to be mirrored.
An illegal port number is used to disable mirroring (which is the default setting). Bit [5] is used to select between
ingress (Rx) or egress (Tx) data.
MIRROR1_DEST: Sets the destination port for the first port mirroring pair. Bits [4:0] select the destination port to be
mirrored. The default is port 23.
MIRROR2_SRC: Sets the source port for the second port mirroring pair. Bits [4:0] select the source port to be
mirrored. An illegal port number is used to disable mirroring (which is the default setting). Bit [5] is used to select
between ingress (Rx) or egress (Tx) data.
MIRROR2_DEST: Sets the destination port for the second port mirroring pair. Bits [4:0] select the destination port to
be mirrored. The default is port 0.
45
Zarlink Semiconductor Inc.
MVTX2604
10.0
TBI Interface
10.1
TBI Connection
Data Sheet
The TBI interface can be used for 1000 Mbps fiber operation. In this mode, the MVTX2604 is connected to the
Serdes as shown in Figure 12. There are two TBI interfaces in the MVTX2604 devices. To enable to TBI function,
the corresponding TXEN and TXER pins need to be boot strapped. See Ball – Signal Description for details.
M25/26_TXD[9:0]
T[9:0]
REFCLK
M25/26_TXCLK
MVTX2604
SERDES
M25/26_RXD[9:0]
R[9:0]
M25/26_RXCLK
RBC0
M25/26_COL
RBC1
Figure 12 - TBI Connection
11.0
GPSI (7WS) Interface
11.1
GPSI connection
The 10/100 RMII ethernet port can function in GPSI (7WS) mode when the corresponding TXEN pin is strapped low
with a 1K pull down resistor. In this mode, the TXD[0], TXD[1], RXD[0] and RXD[1] serve as TX data, TX clock, RX
data and RX clock respectively. The link status and collision from the PHY are multiplexed and shifted into the
switch device through external glue logic. The duplex of the port can be controlled by programming the ECR
register.
The GPSI interface can be operated in port based VLAN mode only.
46
Zarlink Semiconductor Inc.
MVTX2604
CRS_DV
RXD[0]
RXD[1]
TXD[1]
TXD[0]
TXEN
Data Sheet
crs
rxd
rx_clk
tx_clk
link0
Port 0
Ethernet
PHY
col0
txd
txen
link1
260X
link2
col1
col2
SCAN_LINK
SCAN_CLK
SCAN_COL
link23
col23
Port 23
Ethernet
PHY
Link
Serializer
(CPLD)
Collision
Serializer
(CPLD)
Figure 13 - GPSI (7WS) Mode Connection Diagram
47
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
11.2SCAN LINK and SCAN COL interface
An external CPLD logic is required to take the link signals and collision signals from the GPSI PHYs and shift them
into the switch device. The switch device will drive out a signature to indicate the start of the sequence. After that,
the CPLD should shift in the link and collision status of the PHYS as shown in the figure. The extra link status
indicates the polarity of the link signal. One indicates the polarity of the link signal is active high.
scan_clk
scan_link/
scan_col
25 cycles for link/
24 cycles for col
Drived by MVTX260x
Drived by VTX260x
Drived by CPLD
Drived by CPLD
Total 32 cycles period
Total 32 cycles period
Figure 14 - SCAN LINK and SCAN COLLISON Status Diagram
12.0
LED Interface
12.1
LED Interface Introduction
A serial output channel provides port status information from the MVTX2604 chips. It requires three additional pins.
LED_CLK at 12.5 MHz
LED_SYN a sync pulse that defines the boundary between status frames
LED_DATA a continuous serial stream of data for all status LEDs that repeats once every frame time
A non-serial interface is also allowed, but in this case, only the Gigabit ports will have status LEDs.
A low cost external device (44 pin PAL) is used to decode the serial data and to drive an LED array for display. This
device can be customized for different needs.
12.2
Port Status
In the VTX2604, each port has 8 status indicators, each represented by a single bit. The 8 LED status indicators
are:
Bit 0: Flow control
Bit 1:Transmit data
Bit 2: Receive data
Bit 3: Activity (where activity includes either transmission or reception of data)
Bit 4: Link up
Bit 5: Speed (1= 100 Mb/s; 0= 10 Mb/s)
Bit 6: Full-duplex
Bit 7: Collision
48
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
Eight clocks are required to cycle through the eight status bits for each port.
When the LED_SYN pulse is asserted, the LED interface will present 256 LED clock cycles with the clock cycles
providing information for the following ports.
Port 0 (10/100): cycles #0 to cycle #7
Port 1 (10/100): cycles#8 to cycle #15
Port 2 (10/100): cycle #16 to cycle #23
...
Port 22 (10/100): cycle #176 to cycle #183
Port 23 (10/100): cycle #184 to cycle #191
Port 24 (Gigabit 1): cycle #192 to cycle #199
Port 25 (Gigabit 2): cycle #200 to cycle #207
Byte 26 (additional status): cycle #208 to cycle #215
Byte 27 (additional status): cycle #216 to cycle #223
Cycles #224 to 256 present data with a value of zero.
The first two bits of byte 26 provides the speed information for the Gigabit ports while the remainder of byte 26 and
byte 27 provides bist status.
26[0]: G0 port (1= port 24 is operating at Gigabit speed; 0= speed is either 10 or 100 Mb/s depending on
speed bit of Port 24)
26[1]: G1 port (1= port 25 is operating at Gigabit speed; 0= speed is either 10 or 100 Mb/s depending on
speed bit of Port 25)
26[2]: initialization done
26[3]: initialization start
26[4]: checksum ok
26[5]: link_init_complete
26[6]: bist_fail
26[7]: ram_error
27[0]: bist_in_process
27[1]: bist_done
12.3
LED Interface Timing Diagram
The signal from the MVTX2604 to the LED decoder is shown in Figure 15.
Figure 15 - Timing Diagram of LED Interface
49
Zarlink Semiconductor Inc.
MVTX2604
13.0
Hardware Statistics Counter
13.1
Hardware Statistics Counters List
Data Sheet
MVTX2604 hardware provides a full set of statistics counters for each Ethernet port. The CPU accesses these
counters through the CPU interface. All hardware counters are rollover counters. When a counter rolls over the
CPU is interrupted so that long-term statistics may be kept. The MAC detects all statistics except for the delay
exceed discard counter (detected by buffer manager) and the filtering counter (detected by queue manager). The
following is the wrapped signal sent to the CPU through the command block.
31
30
2
6
2
5
0
Status Wrapped Signal
B[0]
0-d
Bytes Sent (D)
B[1]
1-L
Unicast Frame Sent
B[2]
1-U
Frame Send Fail
B[3]
2-I
Flow Control Frames Sent
B[4]
2-u
Non-Unicast Frames Sent
B[5]
3-d
Bytes Received (Good and Bad) (D)
B[6]
4-d
Frames Received (Good and Bad) (D)
B[7]
5-d
Total Bytes Received (D)
B[8]
6-L
Total Frames Received
B9]
6-U
Flow Control Frames Received
B[10]
7-l
Multicast Frames Received
B[11]
7-u
Broadcast Frames Received
B[12]
8-L
Frames with Length of 64 Bytes
B[13]
8-U
Jabber Frames
B[14]
9-L
Frames with Length Between 65-127 Bytes
B[15]
9-U
Oversize Frames
B[16]
A-l
Frames with Length Between 128-255 Bytes
B[17]
A-u
Frames with Length Between 256-511 Bytes
B[18]
B-l
Frames with Length Between 512-1023 Bytes
B[19]
B-u
Frames with Length Between 1024-1528 Bytes
B[20]
C-l
Fragments
B[21]
C-U1
Alignment Error
B[22]
C-U
Undersize Frames
B[23]
D-l
CRC
50
Zarlink Semiconductor Inc.
MVTX2604
B[24]
D-u
Short Event
B[25]
E-l
Collision
B[26]
E-u
Drop
B[27]
F-l
Filtering Counter
B[28]
F-U1
Delay Exceed Discard Counter
B[29]
F-U
Late Collision
B[30]
Link Status Change
B[31]
Current link status
Notation: X-Y
X:
Address in the contain memory
Y:
Size and bits for the counter
d:
D Word counter
L:
24 bits counter bit[23:0]
U:
8 bits counter bit[31:24]
U1:
8 bits counter bit[23:16]
l:
16 bits counter bit[15:0]
u:
16 bits counter bit[31:16]
13.2
IEEE 802.3 HUB Management (RFC 1516)
13.2.1
13.2.1.1
Event Counters
Readablectet
Counts number of bytes (i.e. octets) contained in good valid frames received.
Frame size:
> 64 bytes,
< 1522 bytes if VLAN Tagged;
1518 bytes if not VLAN Tagged
No FCS (i.e. checksum) error
No collisions
51
Zarlink Semiconductor Inc.
Data Sheet
MVTX2604
13.2.1.2
ReadableFrame
Counts number of good valid frames received.
Frame size:
> 64 bytes,
< 1522 bytes if VLAN Tagged;
1518 bytes if not VLAN Tagged
No FCS error
No collisions
13.2.1.3
FCSErrors
Counts number of valid frames received with bad FCS.
Frame size:
> 64 bytes,
< 1522 bytes if VLAN Tagged;
1518 bytes if not VLAN Tagged
No framing error
No collisions
13.2.1.4
AlignmentErrors
Counts number of valid frames received with bad alignment (not byte-aligned).
Frame size:
> 64 bytes,
< 1522 bytes if VLAN Tagged;
1518 bytes if not VLAN Tagged
No framing error
No collisions
13.2.1.5
FrameTooLongs
Counts number of frames received with size exceeding the maximum allowable frame size.
Frame size:
> 64 bytes,
> 1522 bytes if VLAN Tagged;
1518 bytes if not VLAN Tagged
FCS error:
don’t care
Framing error:
don’t care
No collisions
13.2.1.6
ShortEvents
Counts number of frames received with size less than the length of a short event.
Frame size:
< 10 bytes
FCS error:
don’t care
52
Zarlink Semiconductor Inc.
Data Sheet
MVTX2604
Framing error:
Data Sheet
don’t care
No collisions
13.2.1.7
Runts
Counts number of frames received with size under 64 bytes, but greater than the length of a short event.
Frame size:
> 10 bytes,
FCS error:
don’t care
Framing error:
don’t care
< 64 bytes
No collisions
13.2.1.8
Collisions
Counts number of collision events.
Frame size:
13.2.1.9
any size
LateEvents
Counts number of collision events that occurred late (after LateEventThreshold = 64 bytes).
Frame size:
any size
Events are also counted by collision counter
13.2.1.10
VeryLongEvents
Counts number of frames received with size larger than Jabber Lockup Protection Timer (TW3).
Frame size:
13.2.1.11
> Jabber
DataRateMisatches
For repeaters or HUB application only.
13.2.1.12
AutoPartitions
For repeaters or HUB application only.
13.2.1.13
TotalErrors
Sum of the following errors:
FCS errors
Alignment errors
Frame too long
Short events
Late events
Very long events
53
Zarlink Semiconductor Inc.
MVTX2604
13.3
Data Sheet
IEEE – 802.1 Bridge Management (RFC 1286)
13.3.1
Event Counters
13.3.1.1
InFrames
Counts number of frames received by this port or segment.
Note: A frame received by this port is only counted by this counter if and only if it is for a protocol being processed
by the local bridge function.
13.3.1.2
OutFrames
Counts number of frames transmitted by this port.
Note: A frame transmitted by this port is only counted by this counter if and only if it is for a protocol being
processed by the local bridge function.
13.3.1.3
InDiscards
Counts number of valid frames received which were discarded (i.e. filtered) by the forwarding process.
13.3.1.4
DelayExceededDiscards
Counts number of frames discarded due to excessive transmit delay through the bridge.
13.3.1.5
MtuExceededDiscards
Counts number of frames discarded due to excessive size.
13.4
RMON – Ethernet Statistic Group (RFC 1757)
13.4.1
13.4.1.1
Event Counters
Drop Events
Counts number of times a packet is dropped, because of lack of available resources. DOES NOT include all packet
dropping -- for example, random early drop for quality of service support.
13.4.1.2
Octets
Counts the total number of octets (i.e. bytes) in any frames received.
13.4.1.3
BroadcastPkts
Counts the number of good frames received and forwarded with broadcast address.
Does not include non-broadcast multicast frames.
13.4.1.4
MulticastPkts
Counts the number of good frames received and forwarded with multicast address.
Does not include broadcast frames.
54
Zarlink Semiconductor Inc.
MVTX2604
13.4.1.5
CRCAlignErrors
Frame size:
> 64 bytes,
< 1522 bytes if VLAN tag (1518 if no VLAN)
No collisions:
Counts number of frames received with FCS or alignment errors
13.4.1.6
UndersizePkts
Counts number of frames received with size less than 64 bytes.
Frame size:
< 64 bytes,
No FCS error
No framing error
No collisions
13.4.1.7
OversizePkts
Counts number of frames received with size exceeding the maximum allowable frame size.
Frame size:
1522 bytes if VLAN tag (1518 bytes if no VLAN)
FCS error
don’t care
Framing error
don’t care
No collisions
13.4.1.8
Fragments
Counts number of frames received with size less than 64 bytes and with bad FCS.
Frame size:
< 64 bytes
Framing error
don’t care
No collisions
13.4.1.9
Data Sheet
Jabbers
Counts number of frames received with size exceeding maximum frame size and with bad FCS.
Frame size:
> 1522 bytes if VLAN tag (1518 bytes if no VLAN)
Framing error
don’t care
No collisions
55
Zarlink Semiconductor Inc.
MVTX2604
13.4.1.10
Data Sheet
Collisions
Counts number of collision events detected.
Only a best estimate since collisions can only be detected while in transmit mode, but not while in receive mode.
Frame size:
13.4.1.11
any size
Packet Count for Different Size Groups
Six different size groups – one counter for each:
Pkts64Octets
for any packet with size = 64 bytes
Pkts65to127Octets
for any packet with size from 65 bytes to 127 bytes
Pkts128to255Octets
for any packet with size from 128 bytes to 255 bytes
Pkts256to511Octets
for any packet with size from 256 bytes to 511 bytes
Pkts512to1023Octets
for any packet with size from 512 bytes to 1023 bytes
Pkts1024to1518Octets for any packet with size from 1024 bytes to 1518 bytes
Counts both good and bad packets.
13.5
Miscellaneous Counters
In addition to the statistics groups defined in previous sections, the MVTX2604 has other statistics counters for its
own purposes. We have two counters for flow control – one counting the number of flow control frames received,
and another counting the number of flow control frames sent. We also have two counters, one for unicast frames
sent and one for non-unicast frames sent. A broadcast or multicast frame qualifies as non-unicast. Furthermore, we
have a counter called “frame send fail.” This keeps track of FIFO under-runs, late collisions and collisions that have
occurred 16 times.
56
Zarlink Semiconductor Inc.
MVTX2604
14.0
Register Definition
14.1
MVTX2604 Register Description
Register
CPU Addr
(Hex)
Description
Data Sheet
R/W
I2C Addr
(Hex)
Default
0. ETHERNET Port Control Registers Substitute [N] with Port number (0..1A)
ECR1P”N”
Port Control Register 1 for Port N
0000 + 2 x N
R/W
000-01A
020
ECR2P”N”
Port Control Register 2 for Port N
001 + 2 x N
R/W
01B-035
000
GGC
Extra GIGA bit control register
036
R/W
NA
000
1. VLAN Control Registers Substitute [N] with Port number (0..1A)
AVTCL
VLAN Type Code Register Low
100
R/W
036
000
AVTCH
VLAN Type Code Register High
101
R/W
037
081
PVMAP”N”_0
Port “N” Configuration Register 0
102 + 4N
R/W
038-052
0FF
PVMAP”N”_1
Port “N” Configuration Register 1
103 + 4N
R/W
053-06D
0FF
PVMAP”N”_2
Port “N” Configuration Register 2
104 + 4N
R/W
06E-088
0FF
PVMAP”N”_3
Port “N” Configuration Register 3
105 + 4N
R/W
089-0A3
007
PVMODE
VLAN Operating Mode
170
R/W
0A4
000
PVROUTE7-0
VLAN Router Group Enable
171-178
R/W
NA
000
2. TRUNK Control Registers
TRUNK0_L
Trunk Group 0 Low
200
R/W
NA
000
TRUNK0_M
Trunk Group 0 Medium
201
R/W
NA
000
TRUNK0_H
Trunk Group 0 High
202
R/W
NA
000
TRUNK0_
MODE
Trunk Group 0 Mode
203
R/W
0A5
003
TRUNK0_
HASH0
Trunk Group 0 Hash 0 Destination
Port
204
R/W
NA
000
TRUNK0_
HASH1
Trunk Group 0 Hash 1 Destination
Port
205
R/W
NA
001
TRUNK0_
HASH2
Trunk Group 0 Hash 2 Destination
Port
206
R/W
NA
002
TRUNK0_
HASH3
Trunk Group 0 Hash 3 Destination
Port
207
R/W
NA
003
TRUNK1_L
Trunk Group 1 Low
208
R/W
NA
000
TRUNK1_M
Trunk Group 1 Medium
209
R/W
NA
000
57
Zarlink Semiconductor Inc.
Notes
MVTX2604
Register
CPU Addr
(Hex)
Description
Data Sheet
R/W
I2C Addr
(Hex)
Default
TRUNK1_H
Trunk Group 1 High
20A
R/W
NA
000
TRUNK1_
MODE
Trunk Group 1 Mode
20B
R/W
0A6
003
TRUNK1_
HASH0
Trunk Group 1 Hash 0 Destination
Port
20C
R/W
NA
004
TRUNK1_
HASH1
Trunk Group 1 Hash 1 Destination
Port
20D
R/W
NA
005
TRUNK1_
HASH2
Trunk Group 1 Hash 2 Destination
Port
20E
R/W
NA
006
TRUNK1_
HASH3
Trunk Group 1 Hash 3 Destination
Port
20F
R/W
NA
007
TRUNK2_
MODE
Trunk Group 2 Mode
210
R/W
NA
003
TRUNK2_
HASH0
Trunk Group 2 Hash 0 Destination
Port
211
R/W
NA
019
TRUNK2_
HASH1
Trunk Group 2 Hash 1 Destination
Port
212
R/W
NA
01A
Multicast_
HASH0-0
Multicast hash result 0 mask byte
0
220
R/W
NA
0FF
Multicast_
HASH0-1
Multicast hash result 0 mask byte
1
221
R/W
NA
0FF
Multicast_
HASH0-2
Multicast hash result 0 mask byte
2
222
R/W
NA
0FF
Multicast_
HASH0-3
Multicast hash result 0 mask byte
3
223
R/W
NA
0FF
Multicast_
HASH1-0
Multicast hash result 1 mask byte
0
224
R/W
NA
0FF
Multicast_
HASH1-1
Multicast hash result 1 mask byte
1
225
R/W
NA
0FF
Multicast_
HASH1-2
Multicast hash result 1 mask byte
2
226
R/W
NA
0FF
Multicast_
HASH1-3
Multicast hash result 1 mask byte
3
227
R/W
NA
0FF
Multicast_
HASH2-0
Multicast hash result 2 mask byte
0
228
R/W
NA
0FF
Multicast_
HASH2-1
Multicast hash result 2 mask byte
1
229
R/W
NA
0FF
58
Zarlink Semiconductor Inc.
Notes
MVTX2604
Register
CPU Addr
(Hex)
Description
Data Sheet
R/W
I2C Addr
(Hex)
Default
Multicast_
HASH2-2
Multicast hash result 2 mask byte
2
22A
R/W
NA
0FF
Multicast_
HASH2-3
Multicast hash result 2 mask byte
3
22B
R/W
NA
0FF
Multicast_
HASH3-0
Multicast hash result 3 mask byte
0
22C
R/W
NA
0FF
Multicast_
HASH3-1
Multicast hash result 3 mask byte
1
22D
R/W
NA
0FF
Multicast_
HASH3-2
Multicast hash result 3 mask byte
2
22E
R/W
NA
0FF
Multicast_
HASH3-3
Multicast hash result 3 mask byte
3
22F
R/W
NA
0FF
3. CPU Port Configuration
MAC0
CPU MAC Address byte 0
300
R/W
NA
000
MAC1
CPU MAC Address byte 1
301
R/W
NA
000
MAC2
CPU MAC Address byte 2
302
R/W
NA
000
MAC3
CPU MAC Address byte 3
303
R/W
NA
000
MAC4
CPU MAC Address byte 4
304
R/W
NA
000
MAC5
CPU MAC Address byte 5
305
R/W
NA
000
INT_MASK0
Interrupt Mask 0
306
R/W
NA
000
INTP_MASK”N”
Interrupt Mask for MAC Port 2N,
2N+1
310+N (310 313)
R/W
NA
000
RQS
Receive Queue Select
323
R/W
NA
000
RQSS
Receive Queue Status
324
RO
NA
N/A
TX_AGE
Transmission Queue Aging Time
325
R/W
0A7
008
4. Search Engine Configurations
AGETIME_LOW
MAC Address Aging Time Low
400
R/W
0A8
2M:05C/
4M:02E
AGETIME_
HIGH
MAC Address Aging Time High
401
R/W
0A9
000
V_AGETIME
VLAN to Port Aging Time
402
R/W
NA
0FF
SE_OPMODE
Search Engine Operating Mode
403
R/W
NA
000
SCAN
Scan control register
404
R/W
NA
000
59
Zarlink Semiconductor Inc.
Notes
MVTX2604
Register
CPU Addr
(Hex)
Description
Data Sheet
R/W
I2C Addr
(Hex)
Default
5. Buffer Control and QOS Control
FCBAT
FCB Aging Timer
500
R/W
0AA
0FF
QOSC
QOS Control
501
R/W
0AB
000
FCR
Flooding Control Register
502
R/W
0AC
008
AVPML
VLAN Priority Map Low
503
R/W
0AD
000
AVPMM
VLAN Priority Map Middle
504
R/W
0AE
000
AVPMH
VLAN Priority Map High
505
R/W
0AF
000
TOSPML
TOS Priority Map Low
506
R/W
0B0
000
TOSPMM
TOS Priority Map Middle
507
R/W
0B1
000
TOSPMH
TOS Priority Map High
508
R/W
0B2
000
AVDM
VLAN Discard Map
509
R/W
0B3
000
TOSDML
TOS Discard Map
50A
R/W
0B4
000
BMRC
Broadcast/Multicast Rate Control
50B
R/W
0B5
000
UCC
Unicast Congestion Control
50C
R/W
0B6
2M:008/
4M:010
MCC
Multicast Congestion Control
50D
R/W
0B7
050
PR100
Port Reservation for 10/100 Ports
50E
R/W
0B8
2M:024/
4M:036
PRG
Port Reservation for Giga Ports
50F
R/W
0B9
2M:035/
4M:058
SFCB
Share FCB Size
510
R/W
0BA
2M:014/
4M:064
C2RS
Class 2 Reserve Size
511
R/W
0BB
000
C3RS
Class 3 Reserve Size
512
R/W
0BC
000
C4RS
Class 4 Reserve Size
513
R/W
0BD
000
C5RS
Class 5 Reserve Size
514
R/W
0BE
000
C6RS
Class 6 Reserve Size
515
R/W
0BF
000
C7RS
Class 7 Reserve Size
516
R/W
0C0
000
QOSC”N”
QOS Control (N=0 - 5)
517- 51C
R/W
0C1-0C6
000
QOS Control (N=6 - 11)
51D- 522
R/W
NA
000
60
Zarlink Semiconductor Inc.
Notes
MVTX2604
Register
CPU Addr
(Hex)
Description
Data Sheet
R/W
I2C Addr
(Hex)
Default
QOS Control (N=12 - 23)
523- 52E
R/W
0C7-0D2
000
QOS Control (N=24 - 59)
52F- 552
R/W
NA
000
RDRC0
WRED Drop Rate Control 0
553
R/W
0FB
08F
RDRC1
WRED Drop Rate Control 1
554
R/W
0FC
088
USER_
PORT”N”_LOW
User Define Logical Port “N” Low
(N=0-7)
580 + 2N
R/W
0D6-0DD
000
USER_
PORT”N”_HIGH
User Define Logical Port “N” High
581 + 2N
R/W
0DE-0E5
000
USER_
PORT1:0_
PRIORITY
User Define Logic Port 1 and 0
Priority
590
R/W
0E6
000
USER_
PORT3:2_
PRIORITY
User Define Logic Port 3 and 2
Priority
591
R/W
0E7
000
USER_
PORT5:4_
PRIORITY
User Define Logic Port 5 and 4
Priority
592
R/W
0E8
000
USER_
PORT7:6_PRI
ORITY
User Define Logic Port 7 and 6
Priority
593
R/W
0E9
000
USER_PORT_
ENABLE
User Define Logic Port Enable
594
R/W
0EA
000
WLPP10
Well known Logic Port Priority for
1 and 0
595
R/W
0EB
000
WLPP32
Well known Logic Port Priority for
3 and 2
596
R/W
0EC
000
WLPP54
Well known Logic Port Priority for
5 and 4
597
R/W
0ED
000
WLPP76
Well-known Logic Port Priority for
7&6
598
R/W
0EE
000
WLPE
Well known Logic Port Enable
599
R/W
0EF
000
RLOWL
User Define Range Low Bit7:0
59A
R/W
0F4
000
RLOWH
User Define Range Low Bit 15:8
59B
R/W
0F5
000
RHIGHL
User Define Range High Bit 7:0
59C
R/W
0D3
000
RHIGHH
User Define Range High Bit 15:8
59D
R/W
0D4
000
RPRIORITY
User Define Range Priority
59E
R/W
0D5
000
61
Zarlink Semiconductor Inc.
Notes
MVTX2604
Register
CPUQOSC1~3
R/W
I2C Addr
(Hex)
Default
5A0-5A2
R/W
NA
000
CPU Addr
(Hex)
Description
Byte limit for TxQ on CPU port
Data Sheet
6. MISC Configuration Registers
MII_OP0
MII Register Option 0
600
R/W
0F0
000
MII_OP1
MII Register Option 1
601
R/W
0F1
000
FEN
Feature Registers
602
R/W
0F2
010
MIIC0
MII Command Register 0
603
R/W
N/A
000
MIIC1
MII Command Register 1
604
R/W
N/A
000
MIIC2
MII Command Register 2
605
R/W
N/A
000
MIIC3
MII Command Register 3
606
R/W
N/A
000
MIID0
MII Data Register 0
607
RO
N/A
N/A
MIID1
MII Data Register 1
608
RO
N/A
N/A
LED
LED Control Register
609
R/W
0F3
000
DEVICE
Device id and test
60A
R/W
N/A
000
SUM
EEPROM Checksum Register
60B
R/W
0FF
000
7. Port Mirroring Controls
MIRROR1_SRC
Port Mirror 1 Source Port
700
R/W
N/A
07F
MIRROR1_
DEST
Port Mirror 1 Destination Port
701
R/W
N/A
017
MIRROR2_SRC
Port Mirror 2 Source Port
702
R/W
N/A
0FF
MIRROR2_
DEST
Port Mirror 2 Destination Port
703
R/W
N/A
000
F. Device Configuration Register
GCR
Global Control Register
F00
R/W
N/A
000
DCR
Device Status and Signature
Register
F01
RO
N/A
N/A
DCR1
Giga Port status
F02
RO
N/A
N/A
DPST
Device Port Status Register
F03
R/W
N/A
000
DTST
Data read back register
F04
RO
N/A
N/A
DA
DA Register
FFF
RO
N/A
DA
62
Zarlink Semiconductor Inc.
Notes
MVTX2604
14.2
14.2.1
•
•
INDEX_REG1 (only needed for 8-bit mode)
DATA_FRAME_REG
Data of indirectly accessed registers. (8 bits)
Address = 2 (read/write)
14.2.4
•
•
•
INDEX_REG0
Address bits [15:8] for indirectly accessed register addresses
Address = 1 (write only)
14.2.3
•
•
Directly Accessed Registers
Address bits [7:0] for indirectly accessed register addresses
Address = 0 (write only)
14.2.2
•
•
Data Sheet
CONTROL_FRAME_REG
CPU transmit/receive switch frames. (8/16 bits)
Address = 3 (read/write)
Format:
- Send frame from CPU: In sequence)
Frame Data (size should be in multiple of 8-byte)
8-byte of Frame status (Frame size, Destination port #, Frame O.K. status)
- CPU Received frame: In sequence)
8-byte of Frame status (Frame size, Source port #, VLAN tag)
Frame Data
14.2.5
•
•
•
COMMAND&STATUS Register
CPU interface commands (write) and status
Address = 4 (read/write)
When the CPU writes to this register
Bit [0]:
•
Set Control Frame Receive buffer ready after CPU writes a complete frame
into the buffer. This bit is self-cleared.
Bit [1]:
•
Set Control Frame Transmit buffer1 ready after CPU reads out a complete
frame from the buffer. This bit is self-cleared.
Bit [2]:
•
Set Control Frame Transmit buffer2 ready after CPU reads out a complete
frame from the buffer. This bit is self-cleared.
Bit [3]:
•
Set this bit to indicate CPU received a whole frame (transmit FIFO frame
receive done), and flushed the rest of frame fragment. This bit will be selfcleared.
Bit [4]:
•
Set this bit to indicate that the following Write to the Receive FIFO is the last
one (EOF). This bit will be self-cleared.
63
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
Bit [5]:
•
Set this bit to re-start the data that is sent from the CPU to Receive FIFO
(re-align). This feature can be used for software debug. For normal
operation must be '0'.
Bit [6]:
•
Do not use. Must be '0'
Bit [7]:
•
Reserved
When the CPU reads this register:
Bit [0]:
•
Control Frame receive buffer ready, CPU can write a new frame
• 1 – CPU can write a new control command 1
• 0 – CPU has to wait until this bit is 1 to write a new control command 1
Bit [1]:
•
Control Frame transmit buffer1 ready for CPU to read
• 1 – CPU can read a new control command 1
• 0 – CPU has to wait until this bit is 1 to read a new control command
Bit [2]:
•
Control Frame transmit buffer2 ready for CPU to read
• 1 – CPU can read a new control command 1
• 0 – CPU has to wait until this bit is 1 to read a new control command
Bit [3]:
•
Transmit FIFO has data for CPU to read (TXFIFO_RDY)
Bit [4]:
•
Receive FIFO has space for incoming CPU frame (RXFIFO_SPOK)
Bit [5]:
•
Transmit FIFO End Of Frame (TXFIFO_EOF)
Bit [6]:
•
Reserve
Bit [7]:
•
Reserve
64
Zarlink Semiconductor Inc.
MVTX2604
14.2.6
•
•
•
Data Sheet
Interrupt Register
Interrupt sources (8 bits)
Address = 5 (read only)
When CPU reads this register
Bit [0]:
•
CPU frame interrupt
Bit [1]:
•
Control Frame 1 interrupt. Control Frame receive buffer1 has data for CPU
to read
Bit [2]:
•
Control Frame 2 interrupt. Control Frame receive buffer2 has data for CPU
to read
Bit [3]:
•
Gigabit port A interrupt
Bit [4]:
•
Gigabit port B interrupt
Bit [7:5]:
•
Reserve
Note: This register is not self-cleared. After reading CPU has to clear the bit writing 0 to it.
14.2.7
•
•
•
Address = 6 (read/write)
When CPU writes to this register, data is written to the Control Command Frame Receive Buffer
When CPU reads this register, data is read from the Control Command Frame Transmit Buffer1
14.2.8
•
•
Control Command Frame Buffer1 Access Register
Control Command Frame Buffer2 Access Register
Address = 7 (read only)
When CPU reads this register, data is read from the Control Command Frame Transmit Buffer1
14.3
Indirectly Accessed registers
14.4
Group 0 Address MAC Ports Group
14.4.1
ECR1Pn: Port N Control Register
I2C Address 000 - 01A; CPU Address:0000+2xN (N = port number)
Accessed by CPU, serial interface and I2C (R/W)
7
6
Sp State
5
4
2
A-FC
Port Mode
3
1
0
65
Zarlink Semiconductor Inc.
MVTX2604
Bit [0]
Data Sheet
1 - Flow Control Off
0 - Flow Control On
•
•
•
•
•
•
Bit [1]
When Flow Control On:
In half duplex mode the MAC transmitter applies back pressure for flow
control.
In full duplex mode the MAC transmitter sends Flow Control frames when
necessary. The MAC receiver interprets and processes incoming flow
control frames. The Flow Control Frame Received counter is incremented
whenever a flow control is received.
When Flow Control off:
In half duplex mode the MAC Transmitter does not assert flow control by
sending flow control frames or jamming collision.
In full duplex mode the Mac transmitter does not send flow control frames.
The MAC receiver does not interpret or process the flow control frames. The
Flow Control Frame Received counter is not incremented.
1 - Half Duplex - Only in 10/100 mode
0 - Full Duplex
Bit [2]
1 - 10 Mbps
0 - 100 Mbps
Bit [4:3]
00 – Automatic Enable Auto Neg. - This enables hardware state machine
for auto-negotiation.
01 - Limited Disable auto Neg. This disables hardware for speed auto-negotiation. Hardware Poll MII for link status.
10 - Link Down. Force link down (disable the port).
11 - Link Up. The configuration in ECR1[2:0] is used for (speed/half
duplex/full duplex/flow control) setup.
Bit [5]
•
Asymmetric Flow Control Enable.
0 – Disable asymmetric flow control
01 – Enable Asymmetric flow control
Bit [7:6]
•
When this bit is set, and flow control is on (bit[0] = 0), don’t send out a flow
control frame. But MAC receiver interprets and processes flow control
frames.
•
SS - Spanning tree state (802.1D spanning tree protocol) Default is 11.
00 – Blocking: Frame is dropped
01 - Listening:
Frame is dropped
10 - Learning:
Frame is dropped. Source MAC address is learned.
11 - Forwarding: Frame is forwarded. Source MAC address is learned.
66
Zarlink Semiconductor Inc.
MVTX2604
14.4.2
Data Sheet
ECR2Pn: Port N Control Register
I2C Address: 01B-035; CPU Address:0001+2xN (N = port number)
Accessed by CPU and serial interface (R/W)
7
6
5
Security En
Bit [0]:
•
4
QoS Sel
3
Reserve
2
1
0
DisL
Ftf
Futf
Filter untagged frame (Default 0)
• 0: Disable
• 1: All untagged frames from this port are discarded or follow security option when
security is enable
Bit [1]:
•
Filter Tag frame (Default 0)
• 0: Disable
• 1: All tagged frames from this port are discarded or follow security option when
security is enable
Bit [2]:
•
Learning Disable (Default 0)
• 1 Learning is disabled on this port
• 0 Learning is enabled on this port
Bit [3]:
•
Must be ‘1’
Bit [5:4:]
•
•
•
QOS mode selection (Default 00)
Determines which of the 4 sets of QoS settings is used for 10/100 ports.
Note that there are 4 sets of per-queue byte thresholds, and 4 sets of WFQ
ratios programmed. These bits select among the 4 choices for each 10/100
port. Refer to QOS Application Note.
•
•
•
•
00: select class byte limit set 0 and classes WFQ credit set 0
01: select class byte limit set 1 and classes WFQ credit set 1
10: select class byte limit set 2 and classes WFQ credit set 2
11: select class byte limit set 3 and classes WFQ credit set 3
67
Zarlink Semiconductor Inc.
MVTX2604
Bit[7:6]
•
Data Sheet
Security Enable (Default 00). The MVTX2604 checks the incoming data for
one of the following conditions:
1. If the source MAC address of the incoming packet is in the MAC table
and is defined as secure address but the ingress port is not the same as the
port associated with the MAC address in the MAC table.
A MAC address is defined as secure when its entry at MAC table has static
status and bit 0 is set to 1. MAC address bit 0 (the first bit transmitted) indicates whether the address is unicast or multicast. As source addresses are
always unicast bit 0 is not used (always 0). MVTX2600 uses this bit to
define secure MAC addresses.
2. If the port is set as learning disable and the source MAC address of the
incoming packet is not defined in the MAC address table.
3. If the port is configured to filter untagged frames and an untagged frame
arrives or if the port is configured to filter tagged frames and a tagged frame
arrives.
If one of these three conditions occurs the packet will be handled according
to one of the following specified options:
•
CPU installed
•
•
•
•
14.4.3
00 – Disable port security
01 – Discard violating packets
10 – Send packet to CPU and destination port
11 – Send packet to CPU only
GGControl – Extra GIGA Port Control
CPU Address:h036
Accessed by CPU and serial interface (R/W)
7
6
5
4
3
2
1
0
DF
DI
MiiB
RstA
DF
DI
MiiA
RstA
Bit [0]:
•
Reset GIGA port A
• 0: Normal operation (default)
• 1: Reset Gigabit port A. Normally used when a new Phy is connected (Hot swap).
Bit [1]:
•
GIGA port A use MII interface (10/100M)
• 0: Gigabit port operations at 1000 mode (default)
• 1: Gigabit port operations at 10/100 mode
Bit [2]:
•
Device information insertion enable for Gigabit port A
• 0: Disable preamble stack device ID insertion (default).
• 1: Insert stack device ID into the preamble (must be enabled for ring mode).
Bit [3]:
•
GIGA port A direct flow control (MAC to MAC connection). The MVTX2604
supports direct flow control mechanism; the flow control frame is therefore
not sent through the Gigabit port data path.
• 0: Direct flow control disabled (default)
• 1: Direct flow control enabled
68
Zarlink Semiconductor Inc.
MVTX2604
Bit [4]:
•
Data Sheet
Reset GIGA port B
• 0: Normal operation (default)
• 1: Reset Gigabit port B
Bit [5]:
•
GIGA port B use MII interface (10/100M)
• 0: Gigabit port operates at 1000 mode (default)
• 1: Gigabit port operates at 10/100 mode
Bit [6]:
•
Device information attach enable for Gigabit port B
• 0: Disable preamble stack device ID insertion (default)
• 1: Insert stack device ID into the preamble (must be enabled for ring mode).
Bit [7]:
•
GIGA port B direct flow control (MAC to MAC connection). MVTX2604
supports direct flow control mechanism; the flow control frame is therefore
not sent through the Gigabit port data path.
• 0: Direct flow control disabled (default)
• 1: Direct flow control enabled
14.5
14.5.1
Group 1 Address VLAN Group
AVTCL – VLAN Type Code Register Low
I2C Address 036; CPU Address:h100
Accessed by CPU, serial interface and I2C (R/W)
Bit [7:0]:
14.5.2
VLANType_LOW: Lower 8 bits of the VLAN type code (Default 00)
AVTCH – VLAN Type Code Register High
I2C Address 037; CPU Address:h101
Accessed by CPU, serial interface and I2C (R/W)
Bit [7:0]:
14.5.3
VLANType_HIGH: Upper 8 bits of the VLAN type code (Default is 81)
PVMAP00_0 – Port 00 Configuration Register 0
I2C Address 038, CPU Address:h102
Accessed by CPU, serial interface and I2C (R/W)
In Port Based VLAN Mode
Bit [7:0]:
VLAN Mask for ports 7 to 0 (Default FF)
This register indicates the legal egress ports. A “1” on bit 7 means that the packet can be sent to port 7. A
“0” on bit 7 means that any packet destined to port 7 will be discarded. This register works with registers 1,
2 and 3 to form a 27 bit mask to all egress ports.
69
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
In Tag based VLAN Mode
Bit [7:0]:
PVID [7:0] (Default is FF)
This is the default VLAN tag. It works with configuration register PVMAP00_1 [7:5] [3:0] to form a default
VLAN tag. If the received packet is untagged, then the packet is classified with the default VLAN tag. If the
received packet has a VLAN ID of 0, then PVID is used to replace the packet’s VLAN ID.
14.5.4
PVMAP00_1 – Port 00 Configuration Register 1
I2C Address h53, CPU Address:h103
Accessed by CPU, serial interface and I2C (R/W)
In Port based VLAN Mode
Bit [7:0]:
VLAN Mask for ports 15 to 8 (Default is FF)
In Tag based VLAN Mode
7
5
Unitag Port Priority
4
3
Ultrust
PVID
Bit [3:0]:
PVID [11:8] (Default is F)
Bit [4]:
•
0
Untrusted Port. (Default is 1)
This register is used to change the VLAN priority field of a packet to a predetermined priority.
• 1 : VLAN priority field is changed to Bit[7:5] at ingress port
• 0 : Keep VLAN priority field
Bit [7:5]:
14.5.5
•
Untag Port Priority (Default 7)
PVMAP00_2 – Port 00 Configuration Register 2
I2C Address h6E, CPU Address:h104
Accessed by CPU, serial interface and I2C (R/W)
In Port Based VLAN Mode
Bit [7:0]:
•
VLAN Mask for ports 23 to 16 (Default FF)
In Tag based VLAN Mode
This registered is unused
14.5.6
PVMAP00_3 – Port 00 Configuration Register 3
I2C Address h89, CPU Address:h105
Accessed by CPU, serial interface and I2C (R/W)
70
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
In Port Based VLAN Mode
7
6
5
3
FP
en
Drop
Default
priority
2
tx
0
VLAN Mask
Bit [2:0]:
VLAN Mask for ports 26 to 24 (Default 7). Port 24 is the CPU port
Bit [5:3]:
Default Transmit priority. Used when Bit [7] = 1 (Default 0)
•
•
•
•
•
•
•
•
Bit [6]:
000
001
010
011
100
101
110
111
Transmit Priority Level 0 (Lowest)
Transmit Priority Level 1
Transmit Priority Level 2
Transmit Priority Level 3
Transmit Priority Level 4
Transmit Priority Level 5
Transmit Priority Level 6
Transmit Priority Level 7 (Highest)
Default Discard priority. Used when Bit[7]=1 (Default 0)
• 0 - Discard Priority Level 0 (Lowest)
• 1 - Discard Priority Level 1(Highest)
Bit [7]:
Enable Fix Priority (Default 0)
• 0 Disable fix priority. All frames are analyzed. Transmit Priority and Discard
Priority are based on VLAN Tag, TOS or Logical Port.
• 1 Transmit Priority and Discard Priority are based on values programmed in bit
[6:3]
In Tag-based VLAN Mode
Bit [0]:
•
Not used
Bit [1]:
Ingress Filter Enable (Default 1)
• 0 Disable Ingress Filter. Packets with VLAN not belonging to source
port are forwarded, if destination port belongs to the VLAN. Symmetric
VLAN.
• 1 Enable Ingress Filter. Packets with VLAN not belonging to source port
are filtered. Asymmetric VLAN.
Bit [2]:
Force untag out (VLAN tagging is based on 802.1q rule) (Default 1).
• 0 Disable (Default)
• 1 Force untagged output
All packets transmitted from this port are untagged. This register is used
when this port is connected to legacy equipment that does not support
VLAN tagging.
71
Zarlink Semiconductor Inc.
MVTX2604
Bit [5:3]:
Default Transmit priority. Used when Bit [7] = 1 (Default 0)
•
•
•
•
•
•
•
•
Bit [6]:
Data Sheet
000
001
010
011
100
101
110
111
Transmit Priority Level 0 (Lowest)
Transmit Priority Level 1
Transmit Priority Level 2
Transmit Priority Level 3
Transmit Priority Level 4
Transmit Priority Level 5
Transmit Priority Level 6
Transmit Priority Level 7 (Highest)
Default Discard priority Used when Bit [7] =1 (Default 0)
• 0 - Discard Priority Level 0 (Lowest)
• 1 Discard Priority Level 1 (Highest)
Bit [7]:
Enable Fix Priority (Default 0)
• 0 Disable fix priority. All frames are analyzed. Transmit Priority and
Discard Priority are based on VLAN Tag, TOS or Logical Port.
• 1 Transmit Priority and Discard Priority are based on values
programmed in bit [6:3]
14.6
Port Configuration Registers
PVMAP01_0,1,2,3 I2C Address h39,54,6F,8A; CPU Address:h106,107,108,109)
PVMAP02_0,1,2,3 I2C Address h3A,55,70,8B; CPU Address:h10A, 10B, 10C, 10D)
PVMAP03_0,1,2,3 I2C Address h3B,56,71,8C; CPU Address:h10E, 10F, 110, 111)
PVMAP04_0,1,2,3 I2C Address h3C,57,72,8D; CPU Address:h112, 113, 114, 115)
PVMAP05_0,1,2,3 I2C Address h3D,58,73,8E; CPU Address:h116, 117, 118, 119)
PVMAP06_0,1,2,3 I2C Address h3E,59,74,8F; CPU Address:h11A, 11B, 11C, 11D)
PVMAP07_0,1,2,3 I2C Address h3F,5A,75,90; CPU Address:h11E, 11F, 120, 121)
PVMAP08_0,1,2,3 I2C Address h40,5B,76,91; CPU Address:h122, 123, 124, 125)
PVMAP09_0,1,2,3 I2C Address h41,5C,77,92; CPU Address:h126, 127, 128, 129)
PVMAP10_0,1,2,3 I2C Address h42,5D,78,93; CPU Address:h12A, 12B, 12C, 12D)
PVMAP11_0,1,2,3 I2C Address h43,5E,79,94; CPU Address:h12E, 12F, 130, 131)
PVMAP12_0,1,2,3 I2C Address h44,5F,7A,95; CPU Address:h132, 133, 134, 135)
PVMAP13_0,1,2,3 I2C Address h45,60,7B,96; CPU Address:h136, 137, 138, 139)
PVMAP14_0,1,2,3 I2C Address h46,61,7C,97; CPU Address:h13A, h13B, 13C, 13D)
PVMAP15_0,1,2,3 I2C Address h47,62,7D,98; CPU Address:h13E, 13F, 140, 141)
PVMAP16_0,1,2,3 I2C Address h48,63,7E,99; CPU Address:h142, 143, 144, 145)
PVMAP17_0,1,2,3 I2C Address h49,64,7F,9A; CPU Address:h146, 147, 148, 149)
PVMAP18_0,1,2,3 I2C Address h4A,65,80,9B; CPU Address:h14A, 14B, 14C, 14D)
PVMAP19_0,1,2,3 I2C Address h4B,66,81,9C; CPU Address:h14E, 14F, 150, 151)
72
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
PVMAP20_0,1,2,3 I2C Address h4C,67,82,9D; CPU Address:h152, 153, 154, 155)
PVMAP21_0,1,2,3 I2C Address h4D,68,83,9E; CPU Address:h156, 157, 158, 159)
PVMAP22_0,1,2,3 I2C Address h4E,69,84,9F; CPU Address:h15A, 15B, 15C, 15D)
PVMAP23_0,1,2,3 I2C Address h4F,6A,85,A0; CPU Address:h15E, 15F, 160, 161)
PVMAP24_0,1,2,3 I2C Address h50,6B,86,A1; CPU Address:h162, 163, 164, 165) (CPU port)
PVMAP25_0,1,2,3 I2C Address h51,6C,87,A2; CPU Address:h166, 167, 168, 169) (Giagabit port 1)
PVMAP26_0,1,2,3 I2C Address h52,6D,88,A3; CPU Address:h16A, 16B, 16C, 16D) (Gigabit port 2)
14.6.1
PVMODE
I2C Address: h0A4, CPU Address:h170
Accessed by CPU, serial interface (R/W)
7
6
5
4
3
2
1
0
MAC05
MMA
STP
SM0
rPCS
DF
SL
Vmod
Bit [0]:
•
VLAN Mode (Default = 0)
• 1 Tag based VLAN Mode
• 0 Port based VLAN Mode
Bit [1]:
•
Slow learning (Default = 0)
Same function as SE_OP MODE bit 7. Either bit can enable the function;
both need to be turned off to disable the feature.
Bit [2]:
•
Disable dropping of frames with destination MAC addresses
0180C2000001 to 0180C200000F (Default = 0)
• 0: Drop all frames in this range
• 1: Disable dropping of frames in this range
Bit [3]:
•
Disable Reset PCS (Default = 0)
• 0: Enable reset PCS. PCS FIFO will be reset when received a PCS symbol error.
• 1: Disable reset PCS
Bit [4]:
•
Support MAC address 0 (Default = 0)
• 0: MAC address 0 is not learned.
• 1: MAC address 0 is learned.
Bit [5]:
•
Disable IEEE multicast control frame (0180C2000000 to 0180C20000FF)
to CPU in managed mode (Default = 0)
• 0: Packet is forwarded to CPU
• 1: Packet is forwarded as multicast
Bit [6]:
•
Multiple MAC addresses (Default = 0)
• 0: Single MAC address is assigned to CPU. Registers MAC0 to MAC5 are used
to program the CPU MAC address.
• 1: One block of 32 MAC addresses are assigned to CPU. The block is defined in
an increase way from the MAC address programmed in registers MAC0 to
MAC5.
73
Zarlink Semiconductor Inc.
MVTX2604
Bit [7]:
•
Data Sheet
Disable registers MAC 5 – 0 (CPU MAC address) in comparison with
Ethernet frame destination MAC address. When disable, unicast frames
are not forward to CPU. (Default = 0)
• 1: Disable
• 0: Enable
14.6.2
PVROUTE 0
Registers PVROUTE0 to PVROUTE7 allows the VLAN Index to be assigned an address of a router group. This
feature is useful during IP Multicast mode when data is being sent to the VLAN group and no member of the group
registers. By assigning a router group the VLAN group always has a default address to handle the multicast traffic.
CPU Address:h171
Accessed by CPU, serial interface (R/W)
14.6.3
Bit [0]:
•
VLAN Index 8’hC0 has router group and the router group is VLAN Index 8’h40
Bit [1]:
•
VLAN Index 8’hC1 has router group and the router group is VLAN Index 8’h41
Bit [2]:
•
VLAN Index 8’hC2 has router group and the router group is VLAN Index 8’h42
Bit [3]:
•
VLAN Index 8’hC3 has router group and the router group is VLAN Index 8’h43
Bit [4]:
•
VLAN Index 8’hC4 has router group and the router group is VLAN Index 8’h44
Bit [5]:
•
VLAN Index 8’hC5 has router group and the router group is VLAN Index 8’h45
Bit [6]:
•
VLAN Index 8’hC6 has router group and the router group is VLAN Index 8’h46
Bit [7]:
•
VLAN Index 8’hC7 has router group and the router group is VLAN Index 8’h47
PVROUTE1
CPU Address:h172
Accessed by CPU, serial interface (R/W)
Bit [0]:
•
VLAN Index 8’hC8 has router group and the router group is VLAN Index 8’h48
Bit [1]:
•
VLAN Index 8’hC9 has router group and the router group is VLAN Index 8’h48
Bit [2]:
•
VLAN Index 8’hCA has router group and the router group is VLAN Index 8’h4A
Bit [3]:
•
VLAN Index 8’hCB has router group and the router group is VLAN Index 8’h4B
Bit [4]:
•
VLAN Index 8’hCC has router group and the router group is VLAN Index 8’h4C
Bit [5]:
•
VLAN Index 8’hCD has router group and the router group is VLAN Index 8’h4D
Bit [6]:
•
VLAN Index 8’hCE has router group and the router group is VLAN Index 8’h4E
Bit [7]:
•
VLAN Index 8’hCF has router group and the router group is VLAN Index 8’h4F
74
Zarlink Semiconductor Inc.
MVTX2604
14.6.4
Data Sheet
PVROUTE2
CPU Address:h173
Accessed by CPU, serial interface (R/W)
14.6.5
Bit [0]:
•
VLAN Index 8’hD0 has router group and the router group is VLAN Index 8’h50
Bit [1]:
•
VLAN Index 8’hD1 has router group and the router group is VLAN Index 8’h51
Bit [2]:
•
VLAN Index 8’hD2 has router group and the router group is VLAN Index 8’h52
Bit [3]:
•
VLAN Index 8’hD3 has router group and the router group is VLAN Index 8’h53
Bit [4]:
•
VLAN Index 8’hD4 has router group and the router group is VLAN Index 8’h54
Bit [5]:
•
VLAN Index 8’hD5 has router group and the router group is VLAN Index 8’h55
Bit [6]:
•
VLAN Index 8’hD6 has router group and the router group is VLAN Index 8’h56
Bit [7]:
•
VLAN Index 8’hD7 has router group and the router group is VLAN Index 8’h57
PVROUTE3
CPU Address:h174
Accessed by CPU, serial interface (R/W)
14.6.6
Bit [0]:
•
VLAN Index 8’hD8 has router group and the router group is VLAN Index 8’h58
Bit [1]:
•
VLAN Index 8’hD9 has router group and the router group is VLAN Index 8’h59
Bit [2]:
•
VLAN Index 8’hDA has router group and the router group is VLAN Index 8’h5A
Bit [3]:
•
VLAN Index 8’hDB has router group and the router group is VLAN Index 8’h5B
Bit [4]:
•
VLAN Index 8’hDC has router group and the router group is VLAN Index 8’h5C
Bit [5]:
•
VLAN Index 8’hDD has router group and the router group is VLAN Index 8’h5D
Bit [6]:
•
VLAN Index 8’hDE has router group and the router group is VLAN Index 8’h5E
Bit [7]:
•
VLAN Index 8’hDF has router group and the router group is VLAN Index 8’h5F
PVROUTE4
CPU Address:h175
Accessed by CPU, serial interface (R/W)
Bit [0]:
•
VLAN Index 8’hE0 has router group and the router group is VLAN Index 8’h60
Bit [1]:
•
VLAN Index 8’hE1 has router group and the router group is VLAN Index 8’h61
Bit [2]:
•
VLAN Index 8’hE2 has router group and the router group is VLAN Index 8’h62
Bit [3]:
•
VLAN Index 8’hE3 has router group and the router group is VLAN Index 8’h63
Bit [4]:
•
VLAN Index 8’hE4 has router group and the router group is VLAN Index 8’h64
Bit [5]:
•
VLAN Index 8’hE5 has router group and the router group is VLAN Index 8’h65
Bit [6]:
•
VLAN Index 8’hE6 has router group and the router group is VLAN Index 8’h66
Bit [7]:
•
VLAN Index 8’hE7 has router group and the router group is VLAN Index 8’h67
75
Zarlink Semiconductor Inc.
MVTX2604
14.6.7
Data Sheet
PVROUTE5
CPU Address:h176
Accessed by CPU, serial interface (R/W)
14.6.8
Bit [0]:
•
VLAN Index 8’hE8 has router group and the router group is VLAN Index 8’h68
Bit [1]:
•
VLAN Index 8’hE9 has router group and the router group is VLAN Index 8’h69
Bit [2]:
•
VLAN Index 8’hEA has router group and the router group is VLAN Index 8’h6A
Bit [3]:
•
VLAN Index 8’hEB has router group and the router group is VLAN Index 8’h6B
Bit [4]:
•
VLAN Index 8’hEC has router group and the router group is VLAN Index 8’h6C
Bit [5]:
•
VLAN Index 8’hED has router group and the router group is VLAN Index 8’h6D
Bit [6]:
•
VLAN Index 8’hEE has router group and the router group is VLAN Index 8’h6E
Bit [7]:
•
VLAN Index 8’hEF has router group and the router group is VLAN Index 8’h6F
PVROUTE6
CPU Address:h177
Accessed by CPU, serial interface (R/W)
14.6.9
Bit [0]:
•
VLAN Index 8’hF0 has router group and the router group is VLAN Index 8’h70
Bit [1]:
•
VLAN Index 8’hF1 has router group and the router group is VLAN Index 8’h71
Bit [2]:
•
VLAN Index 8’hF2 has router group and the router group is VLAN Index 8’h72
Bit [3]:
•
VLAN Index 8’hF3 has router group and the router group is VLAN Index 8’h73
Bit [4]:
•
VLAN Index 8’hF4 has router group and the router group is VLAN Index 8’h74
Bit [5]:
•
VLAN Index 8’hF5 has router group and the router group is VLAN Index 8’h75
Bit [6]:
•
VLAN Index 8’hF6 has router group and the router group is VLAN Index 8’h76
Bit [7]:
•
VLAN Index 8’hF7 has router group and the router group is VLAN Index 8’h77
PVROUTE7
CPU Address:h178
Accessed by CPU, serial interface (R/W)
Bit [0]:
•
VLAN Index 8’hF8 has router group and the router group is VLAN Index 8’h78
Bit [1]:
•
VLAN Index 8’hF9 has router group and the router group is VLAN Index 8’h79
Bit [2]:
•
VLAN Index 8’hFA has router group and the router group is VLAN Index 8’h7A
Bit [3]:
•
VLAN Index 8’hFB has router group and the router group is VLAN Index 8’h7B
Bit [4]:
•
VLAN Index 8’hFC has router group and the router group is VLAN Index
8’h7C
76
Zarlink Semiconductor Inc.
MVTX2604
14.7
Data Sheet
Bit [5]:
•
VLAN Index 8’hFD has router group and the router group is VLAN Index
8’h7D
Bit [6]:
•
VLAN Index 8’hFE has router group and the router group is VLAN Index 8’h7E
Bit [7]:
•
VLAN Index 8’hFF has router group and the router group is VLAN Index 8’h7F
Group 2 Address Port Trunking Groups
Trunk Group 0 - Up to four 10/100 ports can be selected for trunk group 0.
14.7.1
TRUNK0_L – Trunk group 0 Low (Managed mode only)
CPU Address:h200
Accessed by CPU, serial interface (R/W)
Bit [7:0] Port7-0 bit map of trunk 0. (Default 00)
14.7.2
TRUNK0_M – Trunk group 0 Medium (Managed mode only)
CPU Address:h201
Accessed by CPU, serial interface (R/W)
Bit [7:0] Port15-8 bit map of trunk 0. (Default 00)
14.7.3
TRUNK0_H – Trunk group 0 High (Managed mode only)
CPU Address:h202
Accessed by CPU, serial interface (R/W)
Bit [7:0] Port23-16 bit map of trunk 0. (Default 00)
TRUNK0_H, TRUNK0_M, and TRUNK0_L provide a trunk map for trunk0. If ports 0 and 2 are to be trunked
together bit 0 and bit 2 of TRUNK0_L are set to 1. All others are clear at “0” to indicate that they are not part of
trunk 0. Up to 4 ports can be selected for trunk group 0.
B
i
t
0
B
i
t
7
TRUNK0_H
P
o
r
t
23
B
i
t
0
B
i
t
7
TRUNK0_M
P
o
r
t
16
P
o
r
t
15
Zarlink Semiconductor Inc.
B
i
t
0
TRUNK0_L
P
o
r
t
8
77
B
i
t
7
P
o
r
t
7
P
o
r
t
0
MVTX2604
14.7.4
Data Sheet
TRUNK0_MODE– Trunk group 0 mode
I2C Address h0A5; CPU Address:203
Accessed by CPU, serial interface and I2C (R/W)
7
4
3
2
Hash
Select
Bit [1:0]:
•
1
0
Port
Select
Port selection in unmanaged mode. Input pin TRUNK0 enable/disable
trunk group 0 in unmanaged mode.
00 Reserved
01 Port 0 and 1 are used for trunk0
10 Port 0,1 and 2 are used for trunk0
11 Port 0,1,2 and 3 are used for trunk0
Bit [3:2]
•
Hash Select. The Hash selected is valid for Trunk 0, 1 and 2. (Default
00)
00 Use Source and Destination Mac Address for hashing
01 Use Source Mac Address for hashing
10 Use Destination Mac Address for hashing
11 Use source destination MAC address and ingress physical port
number for hashing
14.7.5
TRUNK0_HASH0 – Trunk group 0 hash result 0 destination port number
CPU Address:h204
Accessed by CPU, serial interface (R/W)
Bit [4:0]
14.7.6
Hash result 0 destination port number (Default 00)
TRUNK0_HASH1 – Trunk group 0 hash result 1 destination port number
CPU Address:h205
Accessed by CPU, serial interface (R/W)
Bit [4:0]
14.7.7
Hash result 1 destination port number (Default 01)
TRUNK0_HASH2 – Trunk group 0 hash result 2 destination port number
CPU Address:h206
Accessed by CPU, serial interface (R/W)
Bit [4:0]
Hash result 2 destination port number (Default 02)
78
Zarlink Semiconductor Inc.
MVTX2604
14.7.8
TRUNK0_HASH3 – Trunk group 0 hash result 3 destination port number
CPU Address:h207
Accessed by CPU, serial interface (R/W)
Bit [4:0]
Hash result 3 destination port number (Default 03)
Trunk Group 1 - Up to four 10/100 ports can be selected for trunk group 1.
14.7.9
TRUNK1_L – Trunk group 1 Low (Managed mode only)
Port selection for trunk group 1.
CPU Address:h208
Accessed by CPU, serial interface (R/W)
Bit [7:0] Port7-0 bit map of trunk 1. (Default 00)
14.7.10
TRUNK1_M – Trunk group 1 Medium (Managed mode only)
CPU Address:h209
Accessed by CPU, serial interface (R/W)
Bit [7:0] Port15-8 bit map of trunk 1. (Default 00)
14.7.11
TRUNK1_H – Trunk group 1 High (Managed mode only)
CPU Address:h20A
Accessed by CPU, serial interface (R/W)
Bit [7:0] Port23-16 bit map of trunk 1. (Default 00)
14.7.12
TRUNK1_MODE – Trunk group 1 mode
I2C Address h0A6; CPU Address:20B
Accessed by CPU, serial interface and I2C (R/W)
7
2
1
0
Port Select
Bit [1:0]:
•
Port selection in unmanaged mode. Input pin TRUNK1
enable/disable trunk group 1 in unmanaged mode.
•
•
•
•
00
01
10
11
Reserved
Port 4 and 5 are used for trunk1
Reserved
Port 4,5,6 and 7 are used for trunk1
79
Zarlink Semiconductor Inc.
Data Sheet
MVTX2604
14.7.13
•
•
•
TRUNK1_HASH0 – Trunk group 1 hash result 0 destination port number
CPU Address:h20C
Accessed by CPU, serial interface (R/W)
Bit [4:0]
Hash result 0 destination port number (Default 04)
14.7.14
TRUNK1_HASH1 – Trunk group 1 hash result 1 destination port number
CPU Address:h20D
Accessed by CPU, serial interface (R/W)
Bit [4:0]
14.7.15
Hash result 1 destination port number (Default 05)
TRUNK1_HASH2 – Trunk group 1 hash result 2 destination port number
CPU Address:h20E
Accessed by CPU, serial interface (R/W)
Bit [4:0]
14.7.16
Hash result 1 destination port number (Default 06)
TRUNK1_HASH3 – Trunk group 1 hash result 3 destination port number
CPU Address:h20F
Accessed by CPU, serial interface (R/W)
Bit [4:0]
Hash result 1 destination port number (Default 07)
Trunk Group 2
14.7.17
TRUNK2_MODE – Trunk group 2 mode (Gigabit ports 1 and 2)
CPU Address:210
Accessed by CPU, serial interface (R/W)
7
6
4
3
0
Ring/trunk Mode
Bit [3:0]
Reserved
Bit [6:4]
000 Normal
001 Trunk Mode. Enable Trunk group for Gigabit port 1 and 2 in
managed mode. In unmanaged mode Trunk 2 is enable/disable
using input pin TRUNK2.
• 010 Single Ring with G1
• 100 Single Ring with G2
• 111 Dual Ring Mode
80
Zarlink Semiconductor Inc.
Data Sheet
MVTX2604
14.7.18
Data Sheet
TRUNK2_HASH0 – Trunk group 2 hash result 0 destination port number
CPU Address:h211
Accessed by CPU, serial interface (R/W)
Bit [4:0]
Hash result 0 destination port number (Default 0x19)
0x19 = Gigabit port 1
0x1A = Gigabit port 2
14.7.19
TRUNK2_HASH1 – Trunk group 2 hash result 1 destination port number
CPU Address:h211
Accessed by CPU, serial interface (R/W)
Bit [4:0]
Hash result 1 destination port number (Default 0x1A)
0x19 = Gigabit port 1
0x1A = Gigabit port 2
14.7.20
Multicast Hash Registers
Multicast Hash registers are used to distribute multicast traffic. 16 registers are used to form a 4-entry array; each
entry has 27 bits, with each bit representing one port. Any port not belonging to a trunk group should be
programmed with 1. Ports belonging to the same trunk group should only have a single port set to “1” per entry.
The port set to “1” is picked to transmit the multicast frame when the hash value is met.
Hash Value =0
HASH0_3
HASH0_2
HASH0_1
HASH0_0
Hash Value =1
HASH1_3
HASH1_2
HASH1_1
HASH1_0
Hash Value =2
HASH2_3
HASH2_2
HASH2_1
HASH2_0
Hash Value =3
HASH3_3
HASH3_2
HASH3_1
HASH3_0
P
o
r
t
26
P
o
r
t
24
C
P
U
P
o
r
t
16
P
o
r
t
23
Multicast_HASH0-0 – Multicast hash result 0 mask byte 0
CPU Address:h220
Accessed by CPU, serial interface (R/W)
Bit [7:0]
(Default FF)
81
Zarlink Semiconductor Inc.
P
o
r
t
15
P P
o o
r r
t
t 7
8
P
o
r
t
0
MVTX2604
14.7.20.1
Data Sheet
Multicast_HASH0-1 – Multicast hash result 0 mask byte 1
CPU Address:h221
Accessed by CPU, serial interface (R/W)
Bit [7:0]
14.7.20.2
(Default FF)
Multicast_HASH0-2 – Multicast hash result 0 mask byte 2
CPU Address:h222
Accessed by CPU, serial interface (R/W)
Bit [7:0]
14.7.20.3
(Default FF)
MULTICAST_HASH0-3 – MULTICAST
HASH RESULT
0
MASK BYTE
3
CPU Address:h223
Accessed by CPU, serial interface (R/W)
Bit [7:0]
14.7.20.4
(Default FF)
Multicast_HASH1-0 – Multicast hash result 1 mask byte 0
CPU Address:h224
Accessed by CPU, serial interface (R/W)
Bit [7:0]
14.7.20.5
(Default FF)
MULTICAST_HASH1-1 – MULTICAST
HASH RESULT
1
MASK BYTE
CPU Address:h225
Accessed by CPU, serial interface (R/W)
Bit [7:0]
14.7.20.6
(Default FF)
Multicast_HASH1-2 – Multicast hash result 1 mask byte 2
CPU Address:h226
Accessed by CPU, serial interface (R/W)
Bit [7:0]
14.7.20.7
(Default FF)
Multicast_HASH1-3 – Multicast hash result 1 mask byte 3
CPU Address:h227
Accessed by CPU, serial interface (R/W)
Bit [7:0]
(Default FF)
82
Zarlink Semiconductor Inc.
1
MVTX2604
14.7.20.8
Data Sheet
Multicast_HASH2-0 – Multicast hash result 2 mask byte 0
CPU Address:h228
Accessed by CPU, serial interface (R/W)
Bit [7:0]
14.7.20.9
(Default FF)
MULTICAST_HASH2-1 – MULTICAST
HASH RESULT
2
MASK BYTE
1
CPU Address:h229
Accessed by CPU, serial interface (R/W)
Bit [7:0]
(Default FF)
14.7.20.10
MULTICAST_HASH2-2 – MULTICAST
HASH RESULT
2
MASK BYTE
2
HASH RESULT
2
MASK BYTE
3
HASH RESULT
3
MASK BYTE
0
HASH RESULT
3
MASK BYTE
1
HASH RESULT
3
MASK BYTE
2
CPU Address:h22A
Accessed by CPU, serial interface (R/W)
Bit [7:0]
(Default FF)
14.7.20.11
MULTICAST_HASH2-3 – MULTICAST
CPU Address:h22B
Accessed by CPU, serial interface (R/W)
Bit [7:0]
(Default FF)
14.7.20.12
MULTICAST_HASH3-0 – MULTICAST
CPU Address:h22C
Accessed by CPU, serial interface (R/W)
Bit [7:0]
(Default FF)
14.7.20.13
MULTICAST_HASH3-1 – MULTICAST
CPU Address:h22D
Accessed by CPU, serial interface (R/W)
Bit [7:0]
(Default FF)
14.7.20.14
MULTICAST_HASH3-2 – MULTICAST
CPU Address:h22E
Accessed by CPU, serial interface (R/W)
Bit [7:0]
(Default FF)
83
Zarlink Semiconductor Inc.
MVTX2604
14.7.20.15
Data Sheet
Multicast_HASH3-3 – Multicast hash result 3 mask byte 3
CPU Address:h22F
Accessed by CPU, serial interface (R/W)
Bit [7:0]
14.8
(Default FF)
Group 3 Address CPU Port Configuration Group
5
MAC5
0
MAC4
MAC3
MAC2
MAC1
MAC0
MAC5 to MAC0 registers form the CPU MAC address. When a packet with destination MAC address match MAC
[5:0], the packet is forwarded to the CPU.
14.8.1
MAC0 – CPU Mac address byte 0
CPU Address:h300
Accessed by CPU
Bit [7:0] Byte 0 of the CPU MAC address. (Default 00)
14.8.2
MAC1 – CPU Mac address byte 1
CPU Address:h301
Accessed by CPU
Bit [7:0] Byte 1 of the CPU MAC address. (Default 00)
14.8.3
MAC2 – CPU Mac address byte 2
CPU Address:h302
Accessed by CPU
Bit [7:0] Byte 2 of the CPU MAC address. (Default 00)
14.8.4
MAC3 – CPU Mac address byte 3
CPU Address:h303
Accessed by CPU
Bit [7:0] Byte 3 of the CPU MAC address. (Default 00)
14.8.5
MAC4 – CPU Mac address byte 4
CPU Address:h304
Accessed by CPU
Bit [7:0] Byte 4 of the CPU MAC address. (Default 00)
84
Zarlink Semiconductor Inc.
MVTX2604
14.8.6
Data Sheet
MAC5 – CPU Mac address byte 5
CPU Address:h305
Accessed by CPU
Bit [7:0] Byte 5 of the CPU MAC address. (Default 00).
14.8.7
INT_MASK0 – Interrupt Mask 0
CPU Address:h306
Accessed by CPU, serial interface (R/W)
The CPU can dynamically mask the interrupt when it is busy and doesn’t want to be interrupted. (Default 0xFF)
Bit [7:0]
MASK
- 1: Mask the interrupt
- 0: Unmask the interrupt (Enable interrupt)
14.8.8
Bit [0]:
•
CPU frame interrupt. CPU frame buffer has data for CPU to read
Bit [1]:
•
Control Command 1 interrupt. Control Command Frame buffer1 has data for
CPU to read
Bit [2]:
•
Control Command 2 interrupt. Control command Frame buffer2 has data for
CPU to read
Bit [7:3]:
•
Reserved
INTP_MASK0 – Interrupt Mask for MAC Port 0,1
CPU Address:h310
Accessed by CPU, serial interface (R/W)
The CPU can dynamically mask the interrupt when it is busy and doesn’t want to be interrupted (Default 0xFF)
7
6
5
4
3
P1
2
1
0
P0
- 1: Mask the interrupt
- 0: Unmask the interrupt
Bit [0]:
Port 0 statistic counter wrap around interrupt mask. An Interrupt is generated when a
statistic counter wraps around. Refer to hardware statistic counter for interrupt
sources.
Bit [1]:
Port 0 link change mask
Bit [4]:
Port 1 statistic counter wrap around interrupt mask.
counter for interupt sources.
Bit [5]:
Port 1 link change mask
85
Zarlink Semiconductor Inc.
Refer to hardware statistic
MVTX2604
14.8.9
INTP_MASK1 – Interrupt Mask for MAC Port 2,3
CPU Address:h311
Accessed by CPU, serial interface (R/W)
14.8.10
INTP_MASK2 – Interrupt Mask for MAC Port 4,5
CPU Address:h312
Accessed by CPU, serial interface (R/W)
14.8.11
INTP_MASK3 – Interrupt Mask for MAC Port 6,7
CPU Address:h313
Accessed by CPU, serial interface (R/W)
14.8.12
INTP_MASK4 – Interrupt Mask for MAC Port 8,9
CPU Address:h314
Accessed by CPU, serial interface (R/W)
14.8.13
INTP_MASK5 – Interrupt Mask for MAC Port 10,11
CPU Address:h315
Accessed by CPU, serial interface (R/W)
14.8.14
INTP_MASK6 – Interrupt Mask for MAC Port 12,13
CPU Address:h316
Accessed by CPU, serial interface (R/W)
14.8.15
INTP_MASK7 – Interrupt Mask for MAC Port 14,15
CPU Address:h317
Accessed by CPU, serial interface (R/W)
14.8.16
INTP_MASK8 – Interrupt Mask for MAC Port 16,17
CPU Address:h318
Accessed by CPU, serial interface (R/W)
14.8.17
NTP_MASK9 – Interrupt Mask for MAC Port 18,19
CPU Address:h319
Accessed by CPU, serial interface (R/W)
86
Zarlink Semiconductor Inc.
Data Sheet
MVTX2604
14.8.18
Data Sheet
INTP_MASK10 – Interrupt Mask for MAC Port 20,21
CPU Address:h31A
Accessed by CPU, serial interface (R/W)
14.8.19
INTP_MASK11 – Interrupt Mask for MAC Port 22,23
CPU Address:h31B
Accessed by CPU, serial interface (R/W)
14.8.20
INTP_MASK12 – Interrupt Mask for MAC Port G1,G2
CPU Address:h31C
Accessed by CPU, serial interface (R/W)
14.8.21
RQS – Receive Queue Select CPU Address:h323)
Accessed by CPU, serial interface (RW)
Select which receive queue is used.
7
FQ3
6
5
4
FQ2
FQ1
FQ0
3
SQ3
2
SQ2
1
SQ1
0
SQ0
Bit [0]:
Select Queue 0. If set to one this queue may be scheduled to CPU port. If set to zero,
this queue will be blocked. If multiple queues are selected, a strict priority will be
applied. Q3> Q2> Q1> Q0. Same applies to bits [3:1]. See QoS Application Note for
more information.
Bit [1]:
Select Queue 1
Bit[2]:
Select Queue 2
Bit [3]:
Select Queue 3
Note: Strip priority applies between different selected queues (Q3>Q2>Q1>Q0)
Bit [4]:
Enable flush Queue 0
Bit [5]:
Enable flush Queue 1
Bit [6]:
Enable flush Queue 2
Bit [7]:
Enable flush Queue 3
When flush (drop frames) is enable, it starts when queue is too long or entry is too old. A queue is too long when it
reaches WRED thresholds. Queue 0 is not subject to early drop. Packets in queue 0 are dropped only when the
queue is too old. An entry is too old when it is older than the time programmed in the register TX_AGE [5:0]. CPU
can dynamically program this register reading register RQSS [7:4].
87
Zarlink Semiconductor Inc.
MVTX2604
14.8.22
Data Sheet
RQSS – Receive Queue Status
CPU Address:h324
Accessed by CPU, serial interface (RO)
7
LQ3
LQ2
5
4
3
LQ1
LQ0
NeQ3
0
NeQ2
NeQ1
NeQ0
CPU receive queue status
Bit [3:0]: Queue 3 to 0 not empty
Bit [4]: Head of line entry for Queue 0 is valid for too long. CPU Queue 0 has no WRED threshold.
Bit [7:5]: Head of line entry for Queue 3 to 1 is valid for too long or Queue length is longer than WRED
threshold.
14.8.23
TX_AGE – Tx Queue Aging timer
I2C Address: h07;CPU Address:h324
Accessed by CPU, serial interface (RW)
7
6
5
0
Tx Queue Agent
Bit [5:0]: Unit of 100ms (Default 8)
Disable transmission queue aging if value is zero. Aging timer for all ports and queues.
This register must be set to 0 for ‘No Packet Loss Flow Control Test’.
14.9
14.9.1
Group 4 Address Search Engine Group
AGETIME_LOW – MAC address aging time Low
I2C Address h0A8; CPU Address:h400
Accessed by CPU, serial interface and I2C (R/W)
The MVTX2600 removes the MAC address from the data base and sends a Delete MAC Address Control
Command to the CPU. MAC address aging is enable/disable by boot strap TSTOUT9.
Bit [7:0] Low byte of the MAC address aging timer.
14.9.2
AGETIME_HIGH –MAC address aging time High
I2C Address h0A9; CPU Address h401
Accessed by CPU, serial interface and I2C (R/W)
Bit [7:0]: High byte of the MAC address aging timer.
The default setting provide 300 seconds aging time. Aging time is based on the following equation:
88
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
{AGETIME_TIME,AGETIME_LOW} X (# of MAC entries in the memory X100µsec). Number of MAC entries = 32 K
when 1 MB is used per Bank. Number of entries = 64 K when 2 MB is used per Bank.
14.9.3
V_AGETIME – VLAN to Port aging time
CPU Address h402
Accessed by CPU (R/W)
Bit [7:0] (Default FF) V_AGETIME X 256 X 100 msec is the age time for the VLAN. This timer is for controlling how
long a port is associated to a particular VLAN. It can use dynamic shrinking of a VLAN domain if no packet arrives
for the VLAN. The 2600 does not remove the port from the VLAN domain. It sends an Age VLAN Port Control
Command to the CPU. The CPU has to remove the port.
14.9.4
SE_OPMODE – Search Engine Operation Mode
CPU Address:h403
Accessed by CPU (R/W)
Note: ECR2[2] enable/disable learning for each port.
7
6
5
4
3
2
1
0
SL
DMS
ARP
DRA
DA
DRD
DRN
FL
Bit [0]:
1 – Enable fast learning mode. In this mode, the hardware learns all
the new MAC addresses at highest rate, and reports to the CPU while
the hardware scans the MAC database. When the CPU report queue is
full, the MAC address is learned and marked as “Not reported”. When
the hardware scans the database and finds a MAC address marked as
“Not Reported” it tries to report it to the CPU. The scan rate must be
set. SCAN Control register sets the scan rate. (Default 0)
0 – Search Engine learns a new MAC address and sends a message
to the CPU report queue. If queue is full, the learning is temporarily
halted.
Bit [1]:
1 – Disable report new VLAN port association(Default 0)
0 – Report new VLAN port association
Bit [2]:
Report control
• 1 – Disable report MAC address deletion (Default 0)
• 0 – Report MAC address deletion (MAC address is deleted from MCT after
aging time)
Bit [3]:
Delete Control
• 1 – Disable aging logic from removing MAC during aging (Default 0)
• 0 – MAC address entry is removed when it is old enough to be aged.
However, a report is still sent to the CPU in both cases, when bit[2] = 0
Bit [4]:
1 – Disable report aging VLAN port association (Default 0)
0 – Enable Report aging VLAN. VLAN is not removed by hardware.
The CPU needs to remove the VLAN –port association.
Bit [5]:
1 - Report ARP packet to CPU (Default 0)
89
Zarlink Semiconductor Inc.
MVTX2604
Bit [6]:
Data Sheet
Disable MCT speedup aging (Default 0)
• 1 – Disable speedup aging when MCT resource is low.
• 0 – Enable speedup aging when MCT resource is low.
Bit [7]:
Slow Learning (Default 0)
• 1– Enable slow learning. Learning is temporary disabled when search
demand is high
• 0 – Learning is performed independent of search demand
14.9.5
SCAN – SCAN Control Register (default 00)
CPU Address h404
Accessed by CPU (R/W)
7
6
0
R
Ratio
SCAN is used when fast learning is enabled (SE_OPMODE bit 0). It is used for setting up the report rate for newly
learned MAC addresses to the CPU.
Bit [6:0]:
•
Ratio between database scanning and aging round (Default 00)
Bit [7]:
•
Reverse the ratio between scanning round and aging round (Default 0)
Examples:
R= 0, Ratio = 0:
All rounds are used for aging. Never scan for new MAC addresses.
R= 0, Ratio = 1:
Aging and scanning in every other aging round
R= 1, Ratio = 7:
In eight rounds, one is used for scanning and seven are used for aging
R= 0, Ratio = 7:
In eight rounds, one is used for aging and seven are used for scanning
14.10
14.10.1
Group 5 Address Buffer Control/QOS Group
FCBAT – FCB Aging Timer
I2C Address h0AA; CPU Address:h500
7
0
FCBAT
Bit [7:0]:
•
•
FCB Aging time. Unit of 1ms. (Default FF)
This is for buffer aging control. It is used to configure the buffer aging
time. This function can be enabled/disabled through bootstrap pin. It
is not suggested to use this function for normal operation.
90
Zarlink Semiconductor Inc.
MVTX2604
14.10.2
Data Sheet
QOSC – QOS Control
I2C Address h0AB; CPU Address:h501
Accessed by CPU, serial interface and I2C (R/W)
7
6
5
4
3
Tos-d
Tos-p
PMCQ
VF1c
1
0
L
Bit [0]:
•
QoS frame lost is OK. Priority will be available for flow control enabled
source only when this bit is set (Default 0)
Bit [4]:
•
Per VLAN Multicast Flow Control (Default 0)
• 0 – Disable
• 1 – Enable
Bit [5]:
•
Select processor multicast queue size
• 0 = 16 entries
• 1 = 64 entries
Bit [6]:
•
Select TOS bits for Priority (Default 0)
• 0 – Use TOS [4:2] bits to map the transmit priority
• 1 – Use TOS [7:5] bits to map the transmit priority
Bit [7]:
•
Select TOS bits for Drop priority(Default 0)
• 0 – Use TOS [4:2] bits to map the drop priority
• 1 – Use TOS [7:5] bits to map the drop priority
14.10.3
FCR – Flooding Control Register
I2C Address h0AC; CPU Address:h502
Accessed by CPU, serial interface and I2C (R/W)
7
6
Tos
TimeBase
Bit [3:0]:
4
•
3
0
U2MR
U2MR: Unicast to Multicast Rate. Units in terms of time base defined in
bits [6:4]. This is used to limit the amount of flooding traffic. The value
in U2MR specifies how many packets are allowed to flood within the
time specified by bit [6:4]. To disable this function, program U2MR to
0. (Default = 8)
91
Zarlink Semiconductor Inc.
MVTX2604
Bit [6:4]:
Data Sheet
Time Base: (Default = 000)
000 = 100 us
001 = 200 us
010 = 400 us
011 = 800 us
100 = 1.6 ms
101 = 3.2 ms
110 = 6.4 ms
111 = 100 us, same as 000.
Bit [7]:
Select VLAN tag or TOS (IP packets) to be preferentially picked to map
transmit priority and drop priority (Default = 0).
0 – Select VLAN Tag priority field over TOS
1 – Select TOS over VLAN tag priority field
14.10.4
AVPML – VLAN Tag Priority Map
I2C Address h0AD; CPU Address:h503
Accessed by CPU, serial interface and I2C (R/W)
7
6
VP2
5
3
2
0
VP1
VP0
Registers AVPML, AVPMM and AVPMH allow the eight VLAN Tag priorities to map into eight Internal level transmit
priorities. Under the Internal transmit priority, seven is the highest priority where as zero is the lowest. This feature
allows the user the flexibility of redefining the VLAN priority field. For example, programming a value of 7 into bit 2:0
of the AVPML register would map packet VLAN priority 0 into Internal transmit priority 7. The new priority is used
inside the 2600. When the packet goes out it carries the original priority.
Bit [2:0]:
Priority when the VLAN tag priority field is 0 (Default 0)
Bit [5:3]:
Priority when the VLAN tag priority field is 1 (Default 0)
Bit [7:6]:
Priority when the VLAN tag priority field is 2 (Default 0)
92
Zarlink Semiconductor Inc.
MVTX2604
14.10.5
Data Sheet
AVPMM – VLAN Priority Map
I2C Address h0AE, CPU Address:h504
Accessed by CPU, serial interface and I2C (R/W)
Map VLAN priority into eight level transmit priorities:
7
6
4
VP5
14.10.6
3
1
VP4
0
VP3
VP2
Bit [0]:
Priority when the VLAN tag priority field is 2 (Default 0)
Bit [3:1]:
Priority when the VLAN tag priority field is 3 (Default 0)
Bit [6:4]:
Priority when the VLAN tag priority field is 4 (Default 0)
Bit [7]:
Priority when the VLAN tag priority field is 5 (Default 0)
AVPMH – VLAN Priority Map
I2C Address h0AF, CPU Address:h505
Accessed by CPU, serial interface and I2C (R/W)
7
5
4
VP7
2
1
VP6
0
VP5
Map VLAN priority into eight level transmit priorities:
14.10.7
Bit [1:0]:
Priority when the VLAN tag priority field is 5 (Default 0)
Bit [4:2]:
Priority when the VLAN tag priority field is 6 (Default 0)
Bit [7:5]:
Priority when the VLAN tag priority field is 7 (Default 0)
TOSPML – TOS Priority Map
I2C Address h0B0, CPU Address:h506
Accessed by CPU, serial interface and I2C (R/W)
7
6
TP2
5
3
2
0
TP1
TP0
Map TOS field in IP packet into eight level transmit priorities
Bit [2:0]:
Priority when the TOS field is 0 (Default 0)
Bit [5:3]:
Priority when the TOS field is 1 (Default 0)
Bit [7:6]:
Priority when the TOS field is 2 (Default 0)
93
Zarlink Semiconductor Inc.
MVTX2604
14.10.8
Data Sheet
TOSPMM – TOS Priority Map
I2C Address h0B1, CPU Address:h507
Accessed by CPU, serial interface and I2C (R/W)
7
6
4
TP5
1
3
TP4
0
TP3
TP2
Map TOS field in IP packet into eight level transmit priorities
14.10.9
Bit [0]:
Priority when the TOS field is 2 (Default 0)
Bit [3:1]:
Priority when the TOS field is 3 (Default 0)
Bit [6:4]:
Priority when the TOS field is 4 (Default 0)
Bit [7]:
Priority when the TOS field is 5 (Default 0)
TOSPMH – TOS Priority Map
I2C Address h0B2, CPU Address:h508
Accessed by CPU, serial interface and I2C (R/W)
7
5
4
TP7
2
1
TP6
0
TP5
Map TOS field in IP packet into eight level transmit priorities:
14.10.10
Bit [1:0]:
Priority when the TOS field is 5 (Default 0)
Bit [4:2]:
Priority when the TOS field is 6 (Default 0)
Bit [7:5]:
Priority when the TOS field is 7 (Default 0)
AVDM – VLAN Discard Map
I2C Address h0B3, CPU Address:h509
Accessed by CPU, serial interface and I2C (R/W)
7
FDV7
6
5
4
3
2
1
FDV6
FDV5
FDV4
FDV3
FDV2
FDV1
0
FDV0
Map VLAN priority into frame discard when low priority buffer usage is above threshold
Bit [0]:
Frame drop priority when VLAN Tag priority field is 0 (Default 0)
Bit [1]:
Frame drop priority when VLAN Tag priority field is 1 (Default 0)
Bit [2]:
Frame drop priority when VLAN Tag priority field is 2 (Default 0)
Bit [3]:
Frame drop priority when VLAN Tag priority field is 3 (Default 0)
94
Zarlink Semiconductor Inc.
MVTX2604
14.10.11
Data Sheet
Bit [4]:
Frame drop priority when VLAN Tag priority field is 4 (Default 0)
Bit [5]:
Frame drop priority when VLAN Tag priority field is 5 (Default 0)
Bit [6]:
Frame drop priority when VLAN Tag priority field is 6 (Default 0)
Bit [7]:
Frame drop priority when VLAN Tag priority field is 7 (Default 0)
TOSDML – TOS Discard Map
I2C Address h0B4, CPU Address:h50A
Accessed by CPU, serial interface and I2C (R/W)
7
FDT7
6
5
4
3
2
1
FDT6
FDT5
FDT4
FDT3
FDT2
FDT1
0
FDT0
Map TOS into frame discard when low priority buffer usage is above threshold
14.10.12
Bit [0]:
Frame drop priority when TOS field is 0 (Default 0)
Bit [1]:
Frame drop priority when TOS field is 1 (Default 0)
Bit [2]:
Frame drop priority when TOS field is 2 (Default 0)
Bit [3]:
Frame drop priority when TOS field is 3 (Default 0)
Bit [4]:
Frame drop priority when TOS field is 4 (Default 0)
Bit [5]:
Frame drop priority when TOS field is 5 (Default 0)
Bit [6]:
Frame drop priority when TOS field is 6 (Default 0)
Bit [7]:
Frame drop priority when TOS field is 7 (Default 0)
BMRC - Broadcast/Multicast Rate Control
I2C Address h0B5, CPU Address:h50B)
Accessed by CPU, serial interface and I2C (R/W)
7
4
Broadcast Rate
3
0
Multicast Rate
This broadcast and multicast rate defines for each port, the number of packets allowed to be forwarded within a
specified time. Once the packet rate is reached, packets will be dropped. To turn off the rate limit, program the field
to 0. Time base is based on register FCR [6:4]
Bit [3:0] :
Multicast Rate Control. Number of multicast packets allowed within the time
defined in bits 6 to 4 of the Flooding Control Register (FCR). (Default 0).
95
Zarlink Semiconductor Inc.
MVTX2604
Bit [7:4] :
14.10.13
Data Sheet
Broadcast Rate Control. Number of broadcast packets allowed within the
time defined in bits 6 to 4 of the Flooding Control Register (FCR). (Default
0)
UCC – Unicast Congestion Control
I2C Address h0B6, CPU Address: 50C
Accessed by CPU, serial interface and I2C (R/W)
7
0
Unicast congest threshold
Bit [7:0] :
14.10.14
Number of frame count. Used for best effort dropping at B% when destination
port’s best effort queue reaches UCC threshold and shared pool is all in use.
Granularity 1 frame. (Default: h10 for 2 MB/bank or h08 for 1 MB/bank)
MCC – Multicast Congestion Control
I2C Address h0B7, CPU Address: 50D
Accessed by CPU, serial interface and I2C (R/W)
7
5
FC reaction period
14.10.15
4
0
Multicast congest threshold
Bit [4:0]:
In multiples of two frames (granularity). Used for triggering MC flow control
when destination port’s multicast best effort queue reaches MCC
threshold.(Default 0x10)
Bit [7:5]:
Flow control reaction period (Default 2) Granularity 4uSec.
PR100 – Port Reservation for 10/100 ports
I2C Address h0B8, CPU Address 50E
Accessed by CPU, serial interface and I2C (R/W)
7
4
Buffer low threshold
Bit [3:0]:
3
0
SP Buffer reservation
Per source port buffer reservation.
Define the space in the FDB reserved for each 10/100 port and CPU.
Expressed in multiples of 4 packets. For each packet 1536 bytes are
reserved in the memory.
96
Zarlink Semiconductor Inc.
MVTX2604
Bits [7:4]:
Data Sheet
Expressed in multiples of 4 packets. Threshold for dropping all best effort
frames when destination port best efforts queues reaches UCC threshold,
shared pool is all used and source port reservation is at or below the
PR100[7:4] level. Also the threshold for initiating UC flow control.
•
Default:
- h36 for 24+2 configuration with memory 2 MB/bank;
- h24 for 24+2 configuration with 1MB/bank;
14.10.16
PRG – Port Reservation for Giga ports
I2C Address h0B9, CPU Address 50F
Accessed by CPU, serial interface and I2C (R/W)
7
4
Buffer low threshold
Bit [3:0]:
3
0
SP buffer reservation
Per source port buffer reservation.
Define the space in the FDB reserved for each Gigabit port. Expressed in
multiples of 16 packets. For each packet 1536 bytes are reserved in the
memory.
Bits [7:4]:
Expressed in multiples of 16 packets. Threshold for dropping all best effort
frames when destination port best effort queues reach UCC threshold,
shared pool is all used and source port reservation is at or below the
PRG[7:4] level. Also the threshold for initiating UC flow control.
•
Default:
- h58 for memory 2 MB/bank;
- h35 for 1 MB/bank;
14.10.17
SFCB – Share FCB Size
I2C Address h0BA), CPU Address 510
Accessed by CPU, serial interface and I2C (R/W)
7
0
Shared pool buffer size
Bits [7:0]:
Expressed in multiples of 4 packets. Buffer reservation for shared pool.
•
Default:
- h64 for 24+2 configuration with memory of 2 MB/bank;
- h14 for 24+2 configuration with memory of 1 MB/bank;
97
Zarlink Semiconductor Inc.
MVTX2604
14.10.18
Data Sheet
C2RS – Class 2 Reserve Size
I2C Address h0BB, CPU Address 511
Accessed by CPU, serial interface and I2C (R/W)
7
0
Class 2 FCB Reservation
Buffer reservation for class 2 (third lowest priority). Granularity 1. (Default 0)
14.10.19
C3RS – Class 3 Reserve Size
I2C Address h0BC, CPU Address 512
Accessed by CPU, serial interface and I2C (R/W)
7
0
Class 3 FCB Reservation
Buffer reservation for class 3. Granularity 1. (Default 0)
14.10.20
C4RS – Class 4 Reserve Size
I2C Address h0BD, CPU Address 513
Accessed by CPU, serial interface and I2C (R/W)
7
0
Class 4 FCB Reservation
Buffer reservation for class 4. Granularity 1. (Default 0)
14.10.21
C5RS – Class 5 Reserve Size
I2C Address h0BE; CPU Address 514
Accessed by CPU, serial interface and I2C (R/W)
7
0
Class 5 FCB Reservation
Buffer reservation for class 5. Granularity 1. (Default 0)
14.10.22
C6RS – Class 6 Reserve Size
I2C Address h0BF; CPU Address 515
Accessed by CPU, serial interface and I2C (R/W)
7
0
Class 6 FCB Reservation
Buffer reservation for class 6 (second highest priority). Granularity 1. (Default 0)
98
Zarlink Semiconductor Inc.
MVTX2604
14.10.23
Data Sheet
C7RS – Class 7 Reserve Size
I2C Address h0C0; CPU Address 516
Accessed by CPU, serial interface and I2C (R/W)
7
0
Class 7 FCB Reservation
Buffer reservation for class 7 (highest priority). Granularity 1. (Default 0)
14.10.24
QOSCn - Classes Byte Limit Set 0
Accessed by CPU; serial interface and I2C (R/W):
C — QOSC00 – BYTE_C01 (I2C Address h0C1, CPU Address 517)
B — QOSC01 – BYTE_C02 (I2C Address h0C2, CPU Address 518)
A — QOSC02 – BYTE_C03 (I2C Address h0C3, CPU Address 519)
QOSC00 through QOSC02 represents one set of values A-C for a 10/100 port when using the Weighted Random
Early Drop (WRED) Scheme described in Chapter 7. There are four such sets of values A-C specified in Classes
Byte Limit Set 0, 1, 2, and 3. For CPU port A-C values are defined using register CPUQOSC1, 2 and 3.
Each 10/ 100 port can choose one of the four Byte Limit Sets as specified by the QoS Select field located in bits 5
to 4 of the ECR2n register. The values A-C are per-queue byte thresholds for random early drop. QOSC02
represents A, and QOSC00 represents C.
Granularity when Delay bound is used: QOSC02: 128 bytes, QOSC01: 256 bytes, QOSC00: 512 bytes. Granularity
when WFQ is used: QOSC02: 512 bytes, QOSC01: 512 bytes, QOSC00: 512 bytes.
14.10.25
Classes Byte Limit Set 1
Accessed by CPU, serial interface and I2C (R/W):
C - QOSC03 – BYTE_C11 (I2C Address h0C4, CPU Address 51a)
B - QOSC04 – BYTE_C12 (I2C Address h0C5, CPU Address 51b)
A - QOSC05 – BYTE_C13 (I2C Address h0C6, CPU Address 51c)
QOSC03 through QOSC05 represents one set of values A-C for a 10/100 port when using the Weighted Random
Early Drop (WRED) scheme.
Granularity when Delay bound is used: QOSC05: 128 bytes, QOSC04: 256 bytes, QOSC03: 512 bytes. Granularity
when WFQ is used: QOSC05: 512 bytes, QOSC04: 512 bytes, QOSC03: 512 bytes.
14.10.26
Classes Byte Limit Set 2
Accessed by CPU and serial interface (R/W):
C - QOSC06 – BYTE_C21 (CPU Address 51d)
B - QOSC07 – BYTE_C22 (CPU Address 51e)
A - QOSC08 – BYTE_C23 (CPU Address 51f)
QOSC06 through QOSC08 represents one set of values A-C for a 10/100 port when using the Weighted Random
Early Drop (WRED) scheme.
99
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
Granularity when Delay bound is used: QOSC08: 128 bytes, QOSC07: 256 bytes, QOSC06: 512 bytes.
Granularity when WFQ is used: QOSC08: 512 bytes, QOSC07: 512 bytes, QOSC06: 512 bytes
14.10.27
Classes Byte Limit Set 3
Accessed by CPU and serial interface (R/W):
C - QOSC09 – BYTE_C31 (CPU Address 520)
B - QOSC10 – BYTE_C32 (CPU Address 521)
A - QOSC11 – BYTE_C33 (CPU Address 522)
QOSC09 through QOSC011 represents one set of values A-C for a 10/100 port when using the Weighted Random
Early Drop (WRED) scheme.
Granularity when Delay bound is used: QOSC11: 128 bytes, QOSC10: 256 bytes, QOSC09: 512 bytes.
Granularity when WFQ is used: QOSC11: 512 bytes, QOSC10: 512 bytes, QOSC09: 512 bytes
14.10.28
Classes Byte Limit Giga Port 1
Accessed by CPU, serial interface and I2C (R/W):
F - QOSC12 – BYTE_C2_G1 (I2C Address h0C7, CPU Address 523)
E - QOSC13 – BYTE_C3_G1 (I2C Address h0C8, CPU Address 524)
D - QOSC14 – BYTE_C4_G1 (I2C Address h0C9, CPU Address 525)
C -QOSC15 – BYTE_C5_G1 (I2C Address h0CA, CPU Address 526)
B - QOSC16 – BYTE_C6_G1 (I2C Address h0CB, CPU Address 527)
A - QOSC17 – BYTE_C7_G1 (I2C Address h0CC, CPU Address 528)
QOSC12 through QOSC17 represent the values A-F for Gigabit port 1. They are per-queue byte thresholds for
random early drop. QOSC17 represents A, and QOSC12 represents F.
Granularity when Delay bound is used: QOSC17 and QOSC16: 256 bytes, QOSC15 and QOSC14: 512 bytes,
QOSC13 and QOSC12: 1024 bytes.
Granularity when WFQ is used: QOSC17 to QOSC12: 1024 bytes
14.10.29
Classes Byte Limit Giga Port 2
Accessed by CPU, serial interface and I2C (R/W)
F - QOSC18 – BYTE_C2_G2 (I2C Address h0CD, CPU Address 529)
E - QOSC19 – BYTE_C3_G2 (I2C Address h0CE, CPU Address 52a)
D - QOSC20 – BYTE_C4_G2 (I2C Address h0CF, CPU Address 52b)
C - QOSC21 – BYTE_C5_G2 (I2C Address h0D0, CPU Address 52c)
B - QOSC22 – BYTE_C6_G2 (I2C Address h0D1, CPU Address 52d)
A - QOSC23 – BYTE_C7_G2 (I2C Address h0D2, CPU Address 52e)
QOSC12 through QOSC17 represent the values A-F for Gigabit port 2. They are per-queue byte thresholds for
random early drop. QOSC17 represents A, and QOSC12 represents F.
100
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
Granularity when Delay bound is used: QOSC17 and QOSC16: 256 bytes, QOSC15 and QOSC14: 512 bytes,
QOSC13 and QOSC12: 1024 bytes.
Granularity when WFQ is used: QOSC17 to QOSC12: 1024 bytes
14.10.30
Classes WFQ Credit Set 0
Accessed by CPU and serial interface
W0 - QOSC24[5:0] – CREDIT_C00 (CPU Address 52f)
W1 - QOSC25[5:0] – CREDIT_C01 (CPU Address 530)
W2 - QOSC26[5:0] – CREDIT_C02 (CPU Address 531)
W3 - QOSC27[5:0] – CREDIT_C03 (CPU Address 532)
QOSC24 through QOSC27 represents one set of WFQ parameters for a 10/100 port. There are four such sets of
values. The granularity of the numbers is 1, and their sum must be 64. QOSC27 corresponds to W3 and QOSC24
corresponds to W0.
QOSC24[7:6]: Priority service type for the ports select this parameter set. Option 1 to option 4.
QOSC25[7]: Priority service allow flow control for the ports select this parameter set.
QOSC25[6]: Flow control pause best effort traffic only
Both flow control allow and flow control best effort only can take effect only the priority type is WFQ.
14.10.31
Classes WFQ Credit Set 1
Accessed by CPU and serial interface
W0 - QOSC28[5:0] – CREDIT_C10 (CPU Address 533)
W1 - QOSC29[5:0] – CREDIT_C11 (CPU Address 534)
W2 - QOSC30[5:0] – CREDIT_C12 (CPU Address 535)
W3 - QOSC31[5:0] – CREDIT_C13 (CPU Address 536)
QOSC28 through QOSC31 represents one set of WFQ parameters for a 10/100 port. There are four such sets of
values. The granularity of the numbers is 1, and their sum must be 64. QOSC31 corresponds to W3 and QOSC28
corresponds to W0.
QOSC28[7:6]: Priority service type for the ports select this parameter set. Option 1 to option 4.
QOSC29[7]: Priority service allow flow control for the ports select this parameter set.
QOSC29[6]: Flow control pause best effort traffic only
14.10.32
Classes WFQ Credit Set 2
Accessed by CPU and serial interface
W0 - QOSC32[5:0] – CREDIT_C20 (CPU Address 537)
W1 - QOSC33[5:0] – CREDIT_C21 (CPU Address 538)
W2 - QOSC34[5:0] – CREDIT_C22 (CPU Address 539)
W3 - QOSC35[5:0] – CREDIT_C23 (CPU Address 53a)
101
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
QOSC35 through QOSC32 represents one set of WFQ parameters for a 10/100 port. There are four such sets of
values. The granularity of the numbers is 1 and their sum must be 64. QOSC35 corresponds to W3 and QOSC32
corresponds to W0.
QOSC32[7:6]: Priority service type for the ports select this parameter set. Option 1 to option 4.
QOSC33[7]: Priority service allow flow control for the ports select this parameter set.
QOSC33[6]: Flow control pause for best effort traffic only
14.10.33
Classes WFQ Credit Set 3
Accessed by CPU and serial interface
W0 - QOSC36[5:0] – CREDIT_C30 (CPU Address 53b)
W1 - QOSC37[5:0] – CREDIT_C31 (CPU Address 53c)
W2 - QOSC38[5:0] – CREDIT_C32 (CPU Address 53d)
W3 - QOSC39[5:0] – CREDIT_C33 (CPU Address 53e)
QOSC39 through QOSC36 represents one set of WFQ parameters for a 10/100 port. There are four such sets of
values. The granularity of the numbers is 1 and their sum must be 64. QOSC39 corresponds to W0 and QOSC36
corresponds to W0.
QOSC36[7:6]: Priority service type for the ports select this parameter set. Option 1 to option 4.
QOSC37[7]: Priority service allow flow control for the ports select this parameter set.
QOSC37[6]: Flow control pause best effort traffic only
14.10.34
Classes WFQ Credit Port G1
Accessed by CPU and serial interface
W0 - QOSC40[5:0] - CREDIT_C0_G1(CPU Address 53f)
[7:6]:
Priority service type. Option 1 to 4.
W1 - QOSC41[5:0] – CREDIT_C1_G1 (CPU Address 540)
[7]: Priority service allow flow control for the ports select this parameter set.
[6]: Flow control pause best effort traffic only
W2 - QOSC42[5:0] – CREDIT_C2_G1 (CPU Address 541)
W3 - QOSC43[5:0] – CREDIT_C3_G1 (CPU Address 542)
W4 - QOSC44[5:0] – CREDIT_C4_G1 (CPU Address 543)
W5 - QOSC45[5:0] – CREDIT_C5_G1 (CPU Address 544)
W6 - QOSC46[5:0] – CREDIT_C6_G1 (CPU Address 545)
W7 - QOSC47[5:0] – CREDIT_C7_G1 (CPU Address 546)
QOSC40 through QOSC47 represents the set of WFQ parameters for Gigabit port 24. The granularity of the
numbers is 1 and their sum must be 64. QOSC47 corresponds to W7 and QOSC40 corresponds to W0. In the 2G
trunk configuration, the sum of all values QOSC40 through QOSC47 must be equal to 128.
102
Zarlink Semiconductor Inc.
MVTX2604
14.10.35
Data Sheet
Classes WFQ Credit Port G2
Accessed by CPU and serial interface
W0 - QOSC48[5:0] – CREDIT_C0_G2(CPU Address 547)
[7:6]: Priority service type. Option 1 to 4
W1 - QOSC49[5:0] – CREDIT_C1_G2(CPU Address 548)
[7]: Priority service allow flow control for the ports select this parameter set.
[6]: Flow control pause best effort traffic only
W2 - QOSC50[5:0] – CREDIT_C2_G2(CPU Address 549)
W3 - QOSC51[5:0] – CREDIT_C3_G2(CPU Address 54a)
W4 - QOSC52[5:0] – CREDIT_C4_G2(CPU Address 54b)
W5 - QOSC53[5:0] – CREDIT_C5_G2(CPU Address 54c)
W6 - QOSC54[5:0] – CREDIT_C6_G2(CPU Address 54d)
W7 - QOSC55[5:0] – CREDIT_C7_G2(CPU Address 54e)
QOSC48 through QOSC55 represents the set of WFQ parameters for Gigabit port 2. The granularity of the
numbers is 1 and their sum must be 64. QOSC55 corresponds to W7 and QOSC48 corresponds to W0. In the 2G
trunk configuration, the sum of all values QOSC48 through QOSC55 must be equal to 128.
14.10.36
Class 6 Shaper Control Port G1
Accessed by CPU and serial interface
QOSC56[5:0] – TOKEN_RATE_G1 (CPU Address 54f). Programs de average rate for gigabit port 1. When equal to
0, shaper is disable. Granularity is 1.
QOSC57[7:0] – TOKEN_LIMIT_G1 (CPU Address 550). Programs the maximum counter for gigabit port 1.
Granularity is 16 bytes.
Shaper is implemented to control the peak and average rate for outgoing traffic with priority 6 (queue 6). Shaper is
limited to gigabit ports and queue P6 when it is in strict priority. QOSC41 programs the peak rate for gigabit port 1.
See Programming QoS Registers Application Note for more information.
14.10.37
Class 6 Shaper Control Port G2
Accessed by CPU and serial interface
QOSC58[5:0] – TOKEN_RATE_G2 (CPU Address 551). Programs de average rate for gigabit port 2. When equal
to 0, shaper is disable. Granularity is 1.
QOSC59[7:0] – TOKEN_LIMIT_G2 (CPU Address 552). Programs the maximum counter for gigabit port 2.
Granularity is 16 bytes.
Shaper is implemented to control the peak and average rate for outgoing traffic with priority 6 (queue 6). Shaper is
limited to gigabit ports and queue P6 when it is in strict priority. QOSC49 programs the peak rate for gigabit port 2.
See Programming QoS Register application note for more information.
103
Zarlink Semiconductor Inc.
MVTX2604
14.10.38
Data Sheet
RDRC0 – WRED Rate Control 0
I2C Address 0FB, CPU Address 553
Accessed by CPU, Serial Interface and IcC (R/W)
7
4
3
X Rate
0
Y Rate
Bits [7:4]:
Corresponds to the frame drop percentage X% for WRED. Granularity
6.25%.
Bits [3:0]:
Corresponds to the frame drop percentage Y% for WRED. Granularity
6.25%.
See Programming QoS Registers application note for more information
14.10.39
RDRC1 – WRED Rate Control 1
I2C Address 0FC, CPU Address 554
Accessed by CPU, Serial Interface and I2C (R/W)
7
Z Rate
4
3
0
B Rate
Bits [7:4]:
Corresponds to the frame drop percentage Z% for WRED. Granularity
6.25%.
Bits [3:0]:
Corresponds to the best effort frame drop percentage B%, when shared pool
is all in use and destination port best effort queue reaches UCC. Granularity
6.25%.
See Programming QoS Registers application note for more information
14.10.40
User Defined Logical Ports and Well Known Ports
The MVTX2600AG supports classifying packet priority through layer 4 logical port information. It can be setup by 8
Well Known Ports, 8 User Defined Logical Ports, and 1 User Defined Range. The 8 Well Known Ports supported
are:
•
•
•
•
•
•
•
•
0:23
1:512
2:6000
3:443
4:111
5:22555
6:22
7:554
Their respective priority can be programmed via Well_Known_Port [7:0] priority register.
Enable can individually turn on/off each Well Known Port if desired.
104
Zarlink Semiconductor Inc.
Well_Known_Port_
MVTX2604
Data Sheet
Similarly, the User Defined Logical Port provides the user programmability to the priority, plus the flexibility to select
specific logical ports to fit the applications. The 8 User Logical Ports can be programmed via User_Port 0-7
registers. Two registers are required to be programmed for the logical port number. The respective priority can be
programmed to the User_Port [7:0] priority register. The port priority can be individually enabled/disabled via
User_Port_Enable register.
The User Defined Range provides a range of logical port numbers with the same priority level. Programming is
similar to the User Defined Logical Port. Instead of programming a fixed port number, an upper and lower limit need
to be programmed, they are: {RHIGHH, RHIGHL} and {RLOWH, RLOWL} respectively. If the value in the upper
limit is smaller or equal to the lower limit, the function is disabled. Any IP packet with a logical port that is less than
the upper limit and more than the lower limit will use the priority specified in RPRIORITY.
14.10.40.1
USER_PORT0_(0~7) – USER DEFINE LOGICAL PORT (0~7)
USER_PORT_0 - I2C Address h0D6 + 0DE; CPU Address 580(Low) + 581(high)
USER_PORT_1 - I2C Address h0D7 + 0DF; CPU Address 582 + 583
USER_PORT_2 - I2C Address h0D8 + 0E0; CPU Address 584 + 585
USER_PORT_3 - I2C Address h0D9 + 0E1; CPU Address 586 + 587
USER_PORT_4 - I2C Address h0DA + 0E2; CPU Address 588 + 589
USER_PORT_5 - I2C Address h0DB + 0E3; CPU Address 58A + 58B
USER_PORT_6 - I2C Address h0DC + 0E4; CPU Address 58C + 58D
USER_PORT_7 - I2C Address h0DD + 0E5; CPU Address 58E + 58F
Accessed by CPU, serial interface and I2C (R/W)
7
0
TCP/UDP Logic Port Low
7
0
TCP/UDP Logic Port High
(Default 00) This register is duplicated eight times from PORT 0 through PORT 7 and allows the CPU to define
eight separate ports.
14.10.40.2
USER_PORT_[1:0]_PRIORITY - User Define Logic Port 1 and 0 Priority
I2C Address h0E6, CPU Address 590
Accessed by CPU, serial interface and I2C (R/W)
7
Priority 1
5
4
3
1
Drop
Priority 0
0
Drop
The chip allows the CPU to define the priority
Bits [3:0]:
Priority setting, transmission + dropping, for logic port 0
Bits [7:4]:
Priority setting, transmission + dropping, for logic port 1 (Default 00)
105
Zarlink Semiconductor Inc.
MVTX2604
14.10.40.3
Data Sheet
USER_PORT_[3:2]_PRIORITY - User Define Logic Port 3 and 2 Priority
I2C Address h0E7, CPU Address 591
Accessed by CPU, serial interface and I2C (R/W)
7
5
Priority 3
14.10.40.4
4
3
1
Drop
Priority 2
0
Drop
USER_PORT_[5:4]_PRIORITY - User Define Logic Port 5 and 4 Priority
I2C Address h0E8, CPU Address 592
Accessed by CPU, serial interface and I2C (R/W)
7
5
Priority 5
4
3
1
Drop
Priority 4
0
Drop
(Default 00)
14.10.40.5
USER_PORT_[7:6]_PRIORITY - USER DEFINE LOGIC PORT 7
AND
6 PRIORITY
I2C Address h0E9, CPU Address 593
Accessed by CPU, serial interface and I2C (R/W)
7
5
Priority 7
4
3
1
Drop
Priority 6
0
Drop
(Default 00)
14.10.40.6
USER_PORT_ENABLE[7:0] – User Define Logic 7 to 0 Port Enables
I2C Address h0EA, CPU Address 594
Accessed by CPU, serial interface and I2C (R/W)
7
6
5
4
3
2
1
0
P7
P6
P5
P4
P3
P2
P1
P0
(Default 00)
14.10.40.7
WELL_KNOWN_PORT[1:0] PRIORITY- Well Known Logic Port 1 and 0 Priority
I2C Address h0EB, CPU Address 595
Accessed by CPU, serial interface and I2C (R/W)
7
Priority 1
5
4
3
1
Drop
Priority 0
0
Drop
Priority 0 - Well known port 23 for telnet applications.
106
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
Priority 1 - Well Known port 512 for TCP/UDP.
(Default 00)
14.10.40.8
WELL_KNOWN_PORT[3:2] PRIORITY- Well Known Logic Port 3 and 2 Priority
I2C Address h0EC, CPU Address 596
Accessed by CPU, serial interface and I2C (R/W)
7
5
Priority 3
4
3
1
Drop
Priority 2
0
Drop
Priority 2 - Well known port 6000 for XWIN.
Priority 3 - Well known port 443 for http.sec
(Default 00)
14.10.40.9
WELL_KNOWN_PORT [5:4] PRIORITY- Well Known Logic Port 5 and 4 Priority
I2C Address h0ED, CPU Address 597
Accessed by CPU, serial interface and I2C (R/W)
7
5
Priority 5
4
3
1
Drop
Priority 4
0
Drop
Priority 4 - Well Known port 111 for sun remote procedure call.
Priority 5 - Well Known port 22555 for IP Phone call setup.
(Default 00)
14.10.40.10
WELL_KNOWN_PORT [7:6] PRIORITY- WELL KNOWN LOGIC PORT 7
I2C Address h0EE, CPU Address 598
Accessed by CPU, serial interface and I2C (R/W)
7
Priority 7
5
4
3
1
Drop
Priority 6
0
Drop
Priority 6 - well know port 22 for ssh.
Priority 7 – well Known port 554 for rtsp.
(Default 00)
107
Zarlink Semiconductor Inc.
AND
6 PRIORITY
MVTX2604
14.10.40.11
Data Sheet
WELL KNOWN_PORT_ENABLE [7:0] – Well Known Logic 7 to 0 Port Enables
I2C Address h0EF, CPU Address 599
Accessed by CPU, serial interface and I2C (R/W)
7
6
5
4
3
2
1
0
P7
P6
P5
P4
P3
P2
P1
P0
1 – Enable
0 - Disable
(Default 00)
14.10.40.12
RLOWL – USER DEFINE RANGE LOW BIT 7:0
I2C Address h0F4, CPU Address: 59a
Accessed by CPU, serial interface and I2C (R/W)
(Default 00)
14.10.40.13
RLOWH – User Define Range Low Bit 15:8
I2C Address h0F5, CPU Address: 59b
Accessed by CPU, serial interface and I2C (R/W)
(Default 00)
14.10.40.14
RHIGHL – User Define Range High Bit 7:0
I2C Address h0D3, CPU Address: 59c
Accessed by CPU, serial interface and I2C (R/W)
(Default 00)
14.10.40.15
RHIGHH – User Define Range High Bit 15:8
I2C Address h0D4, CPU Address: 59d
Accessed by CPU, serial interface and I2C (R/W)
(Default 00)
14.10.40.16
RPRIORITY – User Define Range Priority
I2C Address h0D5, CPU Address: 59e
Accessed by CPU, serial interface and I2C (R/W)
7
4
3
0
Range Transmit Priority
Drop
108
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
RLOW and RHIGH form a range for logical ports to be classified with priority specified in RPRIORITY.
14.10.41
Bit[3:1]
Transmit Priority
Bits[0]:
Drop Priority
CPUQOSC123
CPU Address: 5a0, 5a1, 5a2
Accessed by CPU and serial interface (R/W)
C - CPUQOSC1 – CPU BYTE_C1 I2C Address h0C1, CPU Address 517)
B - CPUQOSC2 – CPU BYTE_C2 I2C Address h0C2, CPU Address 518)
A - CPUQOSC3 – CPU BYTE_C3 I2C Address h0C3, CPU Address 519)
Represents values A-C for a CPU port. The values A-C are per-queue byte thresholds for random early drop.
QOSC3 represents A, and QOSC1 represents C. Granularity: 256 bytes
14.11
14.11.1
Group 6 Address MISC Group
MII_OP0 – MII Register Option 0
I2C Address F0, CPU Address:h600
Accessed by CPU, serial interface and I2C (R/W)
7
6
5
4
hfc
1prst
DisJ
Vendor Spc. Reg Addr
Bits [7]:
0
Half duplex flow control feature
0 = Half duplex flow control always enable
1 = Half duplex flow control by negotiation
Bits [6]:
Link partner reset auto-negotiate disable
Bits [5]:
Disable jabber detection. This is for HomePNA applications or any serial
operation slower than 10 Mbps.
0 = Enable
1 = Disable
Bit [4:0]:
Vendor specified link status register address (null value means don’t use it)
(Default 00). This is used if the Linkup bit position in the PHY is nonstandard.
109
Zarlink Semiconductor Inc.
MVTX2604
14.11.2
Data Sheet
MII_OP1 – MII Register Option 1
I2C Address F1, CPU Address:h601
Accessed by CPU, serial interface and I2C (R/W)
7
4
3
Speed bit location
0
Duplex bit location
Bits [3:0]:
Duplex bit location in vendor specified register
Bits [7:4]:
Speed bit location in vendor specified register
(Default 00)
14.11.3
FEN – Feature Register
I2C Address F2, CPU Address:h602)
Accessed by CPU, serial interface and I2C (R/W)
7
DML
Bits [0]:
6
5
4
3
2
1
Mii
Rp
IP Mul
V-Sp
DS
RC
0
SC
Statistic Counter Enable (Default 0)
•
•
0 – Disable
1 – Enable (all ports)
When statistic counter is enable, an interrupt control frame is generated to
the CPU, every time a counter wraps around. This feature requires an
external CPU.
Bits [1]:
Rate Control Enable (Default 0)
•
•
0 – Disable
1 – Enable; Must also set ECR2Pn[3] = 1
This bit enables/disables the rate control for all 10/100 ports. To start rate
control in a 10/100 port the rate control memory must be programmed. This
feature requires an external CPU. See Programming QoS Registers
Application Note and Processor Interface Application Note for more
information.
Bit [2]:
Support DS EF Code. (Default 0)
•
•
0 – Disable
1 – Enable (all ports)
When 101110 is detected in DS field (TOS[7:2]), the frame priority is set for
110 and drop is set for 0.
110
Zarlink Semiconductor Inc.
MVTX2604
Bit [3]:
Data Sheet
Enable VLAN spanning tree support (Default 0)
•
•
0 – Disable
1 – Enable
When VLAN spanning tree is enable the registers ECR1Pn are NOT used to
program the port spanning tree status. The port status is programmed using
the Control Command Frame.
Bit [4]:
Disable IP Multicast Support (Default 1)
•
•
0 – Enable IP Multicast Support
1 – Disable IP Multicast Support
When enable, IGMP packets are identified by search engine and are passed
to the CPU for processing. IP multicast packets are forwarded to the IP
multicast group members according to the VLAN port mapping table.
Bit [5]:
Enable report to CPU(Default 0)
•
•
0 – Disable report to CPU
1 – Enable report to CPU
When disable new VLAN port association report, new MAC address report or
aging reports are disable for all ports. When enable, register SE_OPEMODE
is used to enable/disable selectively each function.
Bit [6]:
Disable MII Management State Machine (Default 0)
•
•
Bit [7]:
0: Enable MII Management State Machine
1: Disable MII Management State Machine
Disable using MCT Link List structure (Default 0)
0 – Enable using MCT Link structure
1 - Disable using MCT Link List structure
14.11.4
MIIC0 – MII Command Register 0
CPU Address:h603
Accessed by CPU and serial interface only (R/W)
Bit [7:0] - MII Data [7:0]
Note: Before programming MII command: set FEN[6], check MIIC3, making sure no RDY, and no VALID; then
program MII command.
14.11.5
MIIC1 – MII Command Register 1
CPU Address:h604
Accessed by CPU and serial interface only (R/W)
Bit [7:0] - MII Data [15:8]
Note: Before programming MII command: set FEN[6], check MIIC3, making sure no RDY and no VALID; then
program MII command.
111
Zarlink Semiconductor Inc.
MVTX2604
14.11.6
Data Sheet
MIIC2 – MII Command Register 2
CPU Address:h605
Accessed by CPU and serial interface only (R/W)
7
6
5
4
Mii OP
0
Register address
Bit [4:0] -
REG_AD – Register PHY Address
Bit [6:5] -
OP – Operation code “10” for read command and “01” for write command
Note: Before programming MII command: set FEN[6], check MIIC3, making sure no RDY and no VALID; then
program MII command.
14.11.7
MIIC3 – MII Command Register 3
CPU Address:h606
Accessed by CPU and serial interface only (R/W)
7
Rdy
6
Valid
5
4
0
PHY address
Bits [4:0] -
PHY_AD – 5 Bit PHY Address
Bit [6] -
VALID – Data Valid from PHY (Read Only)
Bit [7] -
RDY – Data is returned from PHY (Ready Only)
Note: Before programming MII command: set FEN[6], check MIIC3, making sure no RDY and no VALID; then
program MII command. Writing this register will initiate a serial management cycle to the MII management
interface.
14.11.8
MIID0 – MII Data Register 0
CPU Address:h607
Accessed by CPU and serial interface only (RO)
Bit [7:0] - MII Data [7:0]
14.11.9
MIID1 – MII Data Register 1
CPU Address:h608
Accessed by CPU and serial interface only (RO)
Bit [7:0] - MII Data [15:8]
112
Zarlink Semiconductor Inc.
MVTX2604
14.11.10
Data Sheet
LED Mode – LED Control
CPU Address:h609
Accessed by CPU, serial interface and I2C (R/W)
7
5
4
3
Clock rate
2
1
Hold Time
Bit [0]
Reserved(Default 0)
Bit [2:1]:
Hold time for LED signal (Default 00)
00=8 msec
10=32 msec
Bit [4:3]:
0
01=16 msec
11=64 msec
LED clock frequency (Default 0)
For 100MHz SCLK
00 = 100 M/8 = 12.5 MHz
10 = 100 M/32 = 3.125 MHz
01 = 100 M/16 = 6.25 MHz
11 = 100 M/64 = 1.5625 MHz
For 125 MHz SCLK
00 = 125 M/64 = 1953 KHz
10 = 125 M/512 = 244 KHz
Bit [7:5]:
14.11.11
01 = 125 M/128 = 977 KHz
11 = 125 M/1024 = 122 KHz
Reserved. Must be set to ‘0’ (Default 0)
DEVICE Mode
CPU Address:h60a
Accessed by CPU and serial interface (R/W)
7
4
3
0
Device ID
Bit [1:0]:
Reserved. Must be set to ‘0’ (Default 0)
Bit [2]:
Support < = 1536 frames
0: < = 1518 bytes (< = 1522 bytes with VLAN tag) (Default)
1: < = 1536 bytes
14.11.12
Bit [3:0]:
Reserved. Must be set to ‘0’ (Default 0)
Bit [7:4]:
DEVICE ID (Default 0). This is for stacking operation. This is the stack ID
for loop topology.
CHECKSUM - EEPROM Checksum
I2C Address FF, CPU Address:h60b
Accessed by CPU, serial interface and I2C (R/W)
Bit [7:0]:
(Default 0)
113
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
This register is used in unmanaged mode only. Before requesting that the MVTX2604 updates the EEPROM
device, the correct checksum needs to be calculated and written into this checksum register. The checksum
formula is:
FF
Σ
i2C register = 0
i=0
When the MVTX2604 boots from the EEPROM the checksum is calculated and the value must be zero. If the
checksum is not zeroed the MVTX2604 does not start and pin CHECKSUM_OK is set to zero.
14.12
Group 7 Address Port Mirroring Group
14.12.1
MIRROR1_SRC - Port Mirror source port
CPU Address 700
Accessed by CPU and serial interface (R/W) (Default 7F)
7
6
5
4
0
I/O
Src Port Select
Bit [4:0]:
Source port to be mirrored. Use illegal port number to disable mirroring
Bit [5]:
1 - select ingress data
0 - select egress data
Bit [6]:
Reserved
Bit [7]:
Reserved must be se to '1'
14.12.2
MIRROR1_DEST – Port Mirror destination
CPU Address 701
Accessed by CPU, serial interface (R/W) (Default 17)
7
5
4
0
Dest Port Select
Bit [4:0]:
Port Mirror Destination
When port mirroring is enable, destination port can not serve as a data port.
14.12.3
MIRROR2_SRC – Port Mirror source port
CPU Address 702
Accessed by CPU, serial interface (R/W) (Default FF)
7
6
5
4
0
I/O
Src Port Select
114
Zarlink Semiconductor Inc.
MVTX2604
Bit [4:0]:
Source port to be mirrored. Use illegal port number to disable mirroring
Bit [5]:
1 – select ingress data
Data Sheet
0 – select egress data
14.12.4
Bit [6]
Reserved
Bit [7]
Reserved must be set to '1'
MIRROR2_DEST – Port Mirror destination
CPU Address 703
Accessed by CPU, serial interface (R/W) (Default 00)
7
5
4
0
Dest Port Select
Bit [4:0]:
Port Mirror Destination
When port mirroring is enable, destination port can not serve as a data port.
14.13
14.13.1
Group F Address CPU Access Group
GCR-Global Control Register
CPU Address: hF00
Accessed by CPU and serial interface. (R/W)
7
5
4
Init
Bit [0]:
3
2
1
Reset
Bist
SR
0
SC
Store configuration (Default = 0)
Write ‘1’ followed by ‘0’ to store configuration into external EEPROM
Bit [1]:
Store configuration and reset (Default = 0)
Write ‘1’ to store configuration into external EEPROM and reset chip
Bit [2]:
Start BIST (Default = 0)
Write ‘1’ followed by ‘0’ to start the device’s built-in self-test. The result is
found in the DCR register.
Bit [3]:
Soft Reset (Default = 0)
Write ‘1’ to reset chip
115
Zarlink Semiconductor Inc.
MVTX2604
Bit [4]:
Data Sheet
Initialization Done (Default = 0).
This bit is meaningless in unmanaged mode. In managed mode, CPU write
this bit with ‘1’ to indicate initialization is completed and ready to forward
packets.
1 = Initialization is done.
0 = Initialization is not complete.
14.13.2
DCR-Device Status and Signature Register
CPU Address: hF01
Accessed by CPU and serial interface. (RO)
7
6
Revision
Bit [0]:
5
4
Signature
3
RE
2
1
BinP
BR
0
BW
1: Busy writing configuration to I2C
0: Not busy (not writing configuration to I2C)
Bit [1]:
1: Busy reading configuration from I2C
0: Not busy ( not reading configuration from I2C)
Bit [2]:
1: BIST in progress
0: BIST not running
Bit [3]:
1: RAM Error
0: RAM OK
Bit [5:4]:
Device Signature
11: MVTX2604 device
Bit [7:6]:
Revision
00: Initial Silicon
01: XA1 Silicon
10: Production Silicon
116
Zarlink Semiconductor Inc.
MVTX2604
14.3.13
Data Sheet
DCR1-Giga port status
CPU Address: hF02
Accessed by CPU and serial interface. (RO)
7
6
4
CIC
Bit [1:0]:
3
2
1
GIGA1
0
GIGA0
Giga port 0 strap option
- 00 – 100 Mb MII mode
- 01 – 2 G mode
- 10 – GMII
- 11 – PCS
Bit [3:2]
Giga port 1 strap option
- 00 – 100 Mb MII mode
- 01 – 2 G mode
- 10 – GMII
- 11 – PCS
Bit [7]
Chip initialization completed
117
Zarlink Semiconductor Inc.
MVTX2604
14.3.14
Data Sheet
DPST – Device Port Status Register
CPU Address:hF03
Accessed by CPU and serial interface (R/W)
Bit [4:0]:
Read back index register. This is used for selecting what to read back from
DTST. (Default 00)
- 5’b00000 - Port 0 Operating mode and Negotiation status
- 5’b00001 - Port 1 Operating mode and Negotiation status
- 5’b00010 - Port 2 Operating mode and Negotiation status
- 5’b00011 - Port 3 Operating mode and Negotiation status
- 5’b00100 - Port 4 Operating mode and Negotiation status
- 5’b00101 - Port 5 Operating mode and Negotiation status
- 5’b00110 - Port 6 Operating mode and Negotiation status
- 5’b00111 - Port 7 Operating mode and Negotiation status
- 5’b01000 - Port 8 Operating mode and Negotiation status
- 5’b01001 - Port 9 Operating mode and Negotiation status
- 5’b01010 - Port 10 Operating mode and Negotiation status
- 5’b01011 - Port 11 Operating mode and Negotiation status
- 5’b01100 - Port 12 Operating mode and Negotiation status
- 5’b01101 - Port 13 Operating mode and Negotiation status
- 5’b01110 - Port 14 Operating mode and Negotiation status
- 5’b01111 - Port 15 Operating mode and Negotiation status
- 5’b10000 - Port 16 Operating mode and Negotiation status
- 5’b10001 - Port 17 Operating mode and Negotiation status
- 5’b10010 - Port 18 Operating mode and Negotiation status
- 5’b00011 - Port 19 Operating mode and Negotiation status
- 5’b10100 - Port 20 Operating mode and Negotiation status
- 5’b10101 - Port 21 Operating mode and Negotiation status
- 5’b10110 - Port 22 Operating mode and Negotiation status
- 5’b10111 - Port 23 Operating mode and Negotiation status
- 5’b11000 - Port 24 Operating mode/Neg status (CPU port)
- 5’b11001 - Port 25 Operating mode/Neg status (Gigabit 1)
- 5’b11010 - Port 26 Operating mode/Neg status (Gigabit 2)
118
Zarlink Semiconductor Inc.
MVTX2604
14.3.15
Data Sheet
DTST – Data read back register
CPU Address: hF04
Accessed by CPU and serial interface (RO)
This register provides various internal information as selected in DPST bit[4:0].
Application Note.
7
6
5
MD
Info
Sig
4
3
Giga
Inkdn
2
FE
Refer to the PHY Control
1
0
Fdpx
FcEn
When bit is 1:
Bit [0] – Flow control enable
Bit [1] – Full duplex port
Bit [2] – Fast Ethernet port (if not gigabit port)
Bit [3] – Link is down
Bit [4] – Giga port
Bit [5] – Signal detect (when PCS interface mode)
Bit [6] - 2G signal detect (2G mode only)
Bit [7] – Module detected (for hot swap purpose)
14.3.16
DA – DA Register
CPU Address: hFFF
Accessed by CPU and serial interface (RO)
Always return 8’h DA. Indicate the CPU interface or serial port connection is good.
14.4
TBI Registers
Two sets of TBI registers are used for configure the two Gigabit ports if they are operating in TBI mode. These TBI
registers are located inside the switching chip and they are accessed through the MII command and MII data
registers.
14.4.1
Control Register
MII Address: h00
Read/Write
Bit [15]
Reset PCS logic and all TBI registers
1 = Reset.
0 = Normal operation.
Bit [14]
Reserved. Must be programmed with “0”.
Bit [13]
Speed selection (See bit 6 for complete details)
119
Zarlink Semiconductor Inc.
MVTX2604
Bit [12]
Auto Negotiation Enable
1 = Enable auto-negotiation process.
0 = Disable auto-negotiation process (Default).
Bit [11:10]
Reserved. Must be programmed with “0”
Bit [9]
Restart Auto Negotiation.
1 = Restart auto-negotiation process.
0 = Normal operation (Default).
Bit [8:7]
Reserved.
Bit [6]
Speed Selection
Bit[6][13]
1 1 = Reserved
1 0
=1000 Mb/s (Default)
0 1 =100 Mb/s
0 0 =10 Mb/s
Bit [5:0]
14.4.2
Reserved. Must be programmed with “0”.
Status Register
MII Address: h01
Read Only
Bit [15:9]
Reserved. Always read back as “0”.
Bit [8]
Reserved. Always read back as “1”.
Bit [7:6]
Reserved. Always read back as “0”.
Bit [5]
Auto-Negotiation Complete
1 = Auto-negotiation process completed.
0 = Auto-negotiation process not completed.
Bit [4]
Reserved. Always read back as “0”
Bit [3]
Reserved. Always read back as “1”
Bit [2]
Link Status
1 = Link is up.
0 = Link is down.
Bit [1]
Reserved. Always read back as “0”.
Bit [0]
Reserved. Always read back as “1”.
120
Zarlink Semiconductor Inc.
Data Sheet
MVTX2604
14.4.3
Advertisement Register
MII Address: h04
Read/Write
14.4.4
Bit [15]
Next Page
1 = Has next page capabilities.
0 = Do not has next page capabilities (Default).
Bit [14]
Reserved. Always read back as “0”. Read Only.
Bit [13:12]
Remote Fault. Default is “0”.
Bit [11:9]
Reserved. Always read back as “0”. Read Only.
Bit [8:7]
Pause. Default is “00”
Bit [6]
Half Duplex
1 = Support half duplex (Default).
0 = Do not support half duplex.
Bit [5]
Full duplex
1 = Support full duplex (Default).
0 = Do not support full duplex.
Bit [4:0]
Reserved. Always read back as “0”. Read Only.
Link Partner Ability Register
MII Address: h05
Read Only
Bit [15]
Next Page
1 = Has next page capabilities.
0 = Do not has next page capabilities.
Bit [14]
Acknowledge
Bit [13:12]
Remote Fault.
Bit [11:9]
Reserved. Always read back as “0”.
Bit [8:7]
Pause.
Bit [6]
Half Duplex
1 = Support half duplex.
0 = Do not support half duplex.
Bit [5]
Full duplex
1 = Support full duplex.
0 = Do not support full duplex.
Bit [4:0]
Reserved. Always read back as “0”.
121
Zarlink Semiconductor Inc.
Data Sheet
MVTX2604
14.4.5
Expansion Register
MII Address: h06
Read Only
Bit [15:2]
Reserved. Always read back as “0”.
Bit [1]
Page Received.
1 = A new page has been received.
0 = A new page has not been received.
Bit [0]
14.4.6
Reserved. Always read back as “0”.
Extended Status Register
MII Address: h15
Read Only
Bit [15]
1000 Full Duplex
1 = Support 1000 full duplex operation (Default).
0 = Do not support 1000 full duplex operation.
Bit [14]
1000 Half Duplex
1 = Support 1000 half duplex operation (Default).
0 = Do not support 1000 half duplex operation.
Bit [13:0]
Reserved. Always read back as “0”.
122
Zarlink Semiconductor Inc.
Data Sheet
MVTX2604
15.0
BGA and Ball Signal Descriptions
15.1
BGA Views (Top-View)
15.1.1
1
Data Sheet
Encapsulated view in unmanaged mode
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
LA_D LA_D LA_D LA_D LA_D LA_A LA_O LA_A LA_A LA_A LA_A LA_D LA_D LA_D LA_D LA_D OE_C LA_C TRUN MIRR MIRR SCL
4
7
10
13
15
4
E0_
8
13
16
19
33
36
39
42
45
LK0 LK0
K1
OR4 OR1
A
25
26
LA_D LA_D LA_D LA_D LA_D LA_D LA_A LA_O LA_A LA_A LA_A LA_A LA_D LA_D LA_D LA_D LA_D OE_C LA_C LA_D MIRR MIRR TRUN RESE D0
1
3
6
9
12
14 DSC_ E1_
7
12
15
18
32
35
38
41
44
LK1 LK1
62
OR5 OR2
K2 RVED
B
27
28
29
RO TSTO
SDA ST
BE
UT7
TSTO TSTO
UT8 UT3
C LA_C LA_D LA_D LA_D LA_D LA_D LA_A LA_O LA_W T_MO LA_A LA_A LA_A LA_A LA_D LA_D LA_D LA_D OE_C LA_C P_D TRUN MIRR MIRR AUTO TSTO TSTO TSTO TSTO
LK
0
2
5
8
11
3
E_
E_
DE1
11
14
17
20
34
37
40
43 LK2
LK2
K0
OR3 OR0
FD UT11 UT9 UT4 UT0
D
AGN LA_D LA_D LA_D LA_D LA_D LA_D LA_D LA_D LA_A LA_A LA_W LA_D LA_D LA_D LA_D LA_D LA_D LA_D LA_D LA_D SCAN SCAN TSTO TSTO TSTO TSTO TSTO TSTO
17
19
21
23
25
27
29
31
6
10
E0_
49
51
53
55
57
59
61
63
47
COL CLK UT14 UT13 UT12 UT10 UT5 UT1
D
S C A N T S T O M 2 6 _ M 2 6 _ SMCOADN
LINK UT15 CRS TXER
E
M26_ M26_ M26_
TXCL TXEN MTX
K
CLK
M26_ M26_ M26_
TXD1 TXD1 RXD1
4
5
5
M26_ M26_ M26_
TXD1 TXD1 RXD1
2
3
2
M26_ M26_ M26_
TXD1 TXD1 R
XD9
0
1
_D LA_D LA_D LA_D LA_D LA_D LA_D LA_D LA_A LA_A LA_W LA_D LA_D LA_D LA_D LA_D LA_D LA_D RESE LA_D
E SCLK LA
16
18
20
22
24
26
28
30
5
9
E1_
48
50
52
54
56
58
60 RVED 46
F
AVC
C
RESI SCAN LB_D LB_D
N_
EN
63
62
VCC
VCC
VCC
VCC
VCC
ESE LB_D LB_D LB_D
B _ C TRO
G LL
UT 4 7
K
61
60
_
H
LB_D LB_D LB_D LB_D LB_D
46
45
44
59
58
_D LB_D LB_D LB_D LB_D
J LB
43
42
41
57
56
_D LB_D LB_D LB_D LB_D
K LB
40
39
38
55
54
VDD VDD
TSTO TSTO
UT6 UT2
M26_ M26_
RXD RXCL
V
K
M26_ M26_
RXER COL
M26_
RXD1
3
M26_
RXD1
0
M26_
RXD1
4
M26_
RXD1
1
M26_ M26_ M26_ M26_ M26_
TXD9 TXD8 RXD6 RXD7 RXD8
VDD VDD
L LB_D LB_D LB_D LB_D LB_D
37
36
35
53
52
M26_ M26_ M26_ M26_ M26_
TXD4 TXD6 RXD3 RXD4 RXD5
M26_ M26_ M26_ M26_ M26_
TXD7 TXD5 RXD0 RXD1 RXD2
M
LB_D LB_D LB_D LB_D LB_D
34
33
32
51
50
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
N
LB_A LB_A LB_A LB_D LB_D VCC
18
19
20
49
48
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
P
LB_A LB_A LB_A LB_W LB_ VCC
15
16
17
E0_ WE1_
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VCC M26_ M26_
TXD0 TXD1
GREF
_CLK
1
GREF
MDIO _CLK
0
_A LB_A LB_A LB_A LB_A
R LB
VCC
10
11
12
13
14
VSS
VSS
VSS
VSS
VSS
VSS
VSS
25_ M25_
VCC M
CRS TXER
M D C M _KC L
M25_ M25_ M25_ M25_ M25_
VCC TXCL TXEN MTX RXD RXCL
K
CLK
V
K
T L B5_ A L B6_ A L B7_ A L B8_ A L B9_ A V C C
LB_O LB_O T_MO LB_D LB_D VCC
U E0_
E1_ DE0
31
30
LB_A LB_O LB_W LB_D LB_D
V DSC_ E_
E_
29
28
W
LB_D LB_A LB_A LB_D LB_D
15
3
4
27
26
Y
LB_D LB_D LB_D LB_D LB_D
14
13
12
25
24
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD VDD
VCC M26_ M26_
TXD2 TXD3
M25_
VCC TXD1
4
M25_
TXD1
2
M25_
TXD1
0
M25_
TXD1
5
M25_
TXD1
3
M25_
TXD1
1
M25_
RXD1
5
M25_
RXD1
2
M25_ M25_
RXER COL
M25_
RXD1
3
M25_ M25_
R X D 9 R X0D 1
M25_
RXD1
4
M25_
RXD1
1
M25_ M25_ M25_ M25_ M25_
RXD6 TXD8 RXD9 RXD7 RXD8
VDD VDD
A LB_D LB_D LB_D LB_D LB_D
11
10
9
23
22
A
M25_ M25_ M25_ M25_ M25_
TXD6 TXD7 RXD3 RXD4 RXD5
A LB_D LB_D LB_D LB_D LB_D
8
7
6
21
20
B
M25_ M25_ M25_ M25_ M25_
TXD4 TXD5 RXD0 RXD1 RXD2
A LB_D LB_D LB_D LB_D LB_D
5
4
3
19
18
C
M25_ M25_ M23_ M23_ M23_
TXD2 TXD3 CRS RXD0 RXD1
A LB_D LB_D LB_D LB_D LB_D
2
1
0
17
16
D
VCC
VCC
VCC
VCC
M25_ M25_ M23_ M23_ M23_
TXD0 TXD1 TXD1 TXD0 TXEN
VCC
A M0_T M0_T M0_T M3_T M3_T M3_R M5_T M5_T M5_R M8_T M8_T M8_R M10_ M10_ M10_ M13_ M16_ M15_ M16_ M15_ M15_ M18_ M18_ M18_ M20_ M20_ M20_ M22_
E XEN XD0 XD1 XD1 XEN XD0 XD1 XEN XD0 XD1 XEN XD0 TXD1 TXEN RXD0 TXD1 TXD0 TXD1 RXD1 TXEN RXD0 TXD1 TXEN RXD0 TXD1 TXEN RXD0 RXD1
0_R M0_R M0_C M3_T M3_C M3_R M5_T M5_C M5_R M8_T M8_C M8_R M10_ M10_ M10_ M13_ M13_ M13_ M14_ M16R M15_ M17_ M17_ M18_ M20_ M20_ M20_ M22_ M22_
AF M
XD1 XD0
RS
XD0
RS
XD1 XD0
RS
XD1 XD0
RS
XD1 TXD0 CRS RXD1 TXD0 CRS RXD1 CRS XD0 RXD1 RXD0 CRS RXD1 TXD0 CRS RXD1 RXD0 CRS
A M1_T M1_T M1_T M2_T M2_C M4_T M4_C M6_T M6_C M7_T M7_C M9_T M9_C M11_ M11_ M12_ M12_ M14_ M15_ M16_ M16_ M18_ M18_ M19_ M19_ M21_ M21_ M22_ M22_
RS
XD1
RS
XD1
RS
XD1
RS
XD1
RS TXD1 CRS TXD1 CRS TXD1 TXD0 TXD1 CRS TXD0 CRS TXD1 CRS TXD1 CRS TXEN TXD0
G XEN XD0 XD1 XD1
A
H
M1_R M1_C M2_T M2_R M4_T M4_R M6_T M6_R M7_T M7_R M9_T M9_R M11_ M11_ M12_ M12_ M14_ M14_ M13_ M15_ M17_ M17_ M19_ M19_ M21_ M21_ M22_
XD0
RS
XD0 XD0 XD0 XD0 XD0 XD0 XD0 XD0 XD0 XD0 TXD0 RXD0 TXD0 RXD0 TXD0 RXD0 RXD0 CRS TXD0 RXD1 TXD0 RXD0 TXD0 RXD0 TXD1
AJ
M1_R M2_T M2_R M4_T M4_R M6_T M6_R M7_T M7_R M9_T M9_R M11_ M11_ M12_ M12_ M14_ M14_ M16_ M13_ M17_ M17_ M19_ M19_ M21_ M21_
XD1 XEN XD1 XEN XD1 XEN XD1 XEN XD1 XEN XD1 TXEN RXD1 TXEN RXD1 TXEN RXD1 TXEN TXEN TXEN TXD1 TXEN RXD1 TXEN RXD1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
123
Zarlink Semiconductor Inc.
18
19
20
21
22
23
24
25
26
27
28
29
MVTX2604
15.1.2
1
Data Sheet
Encapsulated view in managed mode
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
A
LA_D LA_D LA_D LA_D LA_D LA_A LA_O LA_A LA_A LA_A LA_A LA_D LA_D LA_D LA_D LA_D P_DA P_DA P_DA P_DA P_DA P_A0 P_A1 P_WE T STO
UT7
4
7
10
13
15
4
E0_
8
13
16
19
33
36
39
42
45
TA13 TA10 TA7 TA4 TA1
B
LA_D LA_D LA_D LA_D LA_D LA_D LA_A LA_O LA_A LA_A LA_A LA_A LA_D LA_D LA_D LA_D LA_D P_DA P_DA LA_D P_DA P_DA P_DA P_IN
TSTO TSTO
P_RD
1
3
6
9
12
14 DSC_ E1_
7
12
15
18
32
35
38
41
44
TA14 TA11
62
TA5 TA2 TA6
T
UT8 UT3
29
PDA P_CS TSTO TSTO TSTO TSTO
C L A _ C L A _ D L A _ D L A _ D L A _ D L A _ D L A _ A L A _ O L A _ W T _ M O L A _ A L A _ A L A _ A L A _ A L A _ D L A _ D L A _ D L A _ D P _ D A P _ D A P _ D A P _ A 2 D A T A PT_A
UT11 UT9 UT4 UT0
0
LK
0
2
5
8
11
3
E_
E_
DE1
11
14
17
20
34
37
40
43
TA15 TA12 TA9
3
D
AGN LA_D LA_D LA_D LA_D LA_D LA_D LA_D LA_D LA_A LA_A LA_W LA_D LA_D LA_D LA_D LA_D LA_D LA_D LA_D LA_D SCAN SCAN TSTO TSTO TSTO TSTO TSTO TSTO
17
19
21
23
25
27
29
31
6
10
E0_
49
51
53
55
57
59
61
63
47
COL CLK UT14 UT13 UT12 UT10 UT5 UT1
D
SCAN
SCAN TSTO M26_ M26_ MOD
LINK UT15 CRS TXER
E
M26_ M26_ M26_
MTX
TXCL
TXEN CLK
K
M26_ M26_ M26_
TXD1 TXD1 RXD1
4
5
5
M26_ M26_ M26_
TXD1 TXD1 RXD1
2
3
2
M26_ M26_ M26_
TXD1 TXD1 R
XD9
1
0
E SCLK LA_D LA_D LA_D LA_D LA_D LA_D LA_D LA_D LA_A LA_A LA_W LA_D LA_D LA_D LA_D LA_D LA_D LA_D P_DA LA_D
16
18
20
22
24
26
28
30
5
9
E1_
48
50
52
54
56
58
60
TA8
46
F
AVC
C
RESI SCAN LB_D LB_D
N_
EN
63
62
VCC
VCC
VCC
VCC
VCC
RESE
G LB_ C T O UT LB_ D LB_ D LB_ D
LK
47
61
60
_
H LB_D LB_D LB_D LB_D LB_D
46
45
44
59
58
J LB_D LB_D LB_D LB_D LB_D
43
42
41
57
56
K LB_D LB_D LB_D LB_D LB_D
40
39
38
55
54
VDD VDD
TSTO TSTO
UT6 UT2
M26_ M26_
RXD RXCL
K
V
M26_ M26_
RXER COL
M26_
RXD1
3
M26_
RXD1
0
M26_
RXD1
4
M26_
RXD1
1
M26_ M26_ M26_ M26_ M26_
TXD9 TXD8 RXD6 RXD7 RXD8
VDD VDD
M26_ M26_ M26_ M26_ M26_
TXD4 TXD6 RXD3 RXD4 RXD5
L LB_D LB_D LB_D LB_D LB_D
37
36
35
53
52
M
LB_D LB_D LB_D LB_D LB_D
34
33
32
51
50
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
N
LB_A LB_A LB_A LB_D LB_D VCC
18
19
20
49
48
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
P
LB_A LB_A LB_A LB_W LB_ VCC
15
16
17
E0_ WE1_
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VCC M26_ M26_
TXD0 TXD1
_A LB_A LB_A LB_A LB_A
R LB
VCC
10
11
12
13
14
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VCC
M25_ M25_ M25_ M25_ M25_
VCC TXCL TXEN MTX RXD RXCL
K
V
CLK
K
T L B5_ A L B6_ A L B7_ A L B8_ A L B9_ A V C C
LB_O LB_O T_MO LB_D LB_D VCC
U E0_
E1_
DE0
31
30
LB_A LB_O LB_W LB_D LB_D
V DSC_ E_
E_
29
28
W
LB_D LB_A LB_A LB_D LB_D
15
3
4
27
26
Y
LB_D LB_D LB_D LB_D LB_D
14
13
12
25
24
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD VDD
M26_ M26_ M26_ M26_ M26_
TXD7 TXD5 RXD0 RXD1 RXD2
GREF
_CLK
1
GREF
MDIO _CLK
0
VCC M26_ M26_
TXD2 TXD3
M25_ M25_
CRS TXER
M25_
VCC TXD1
4
M25_
TXD1
2
M25_
TXD1
0
M25_
TXD1
5
M25_
TXD1
3
M25_
TXD1
1
MDC
M25_
RXD1
5
M25_
RXD1
2
M_CL
K
M25_ M25_
RXER COL
M25_
RXD1
3
M25_
M25_ RXD1
RXD9
0
M25_
RXD1
4
M25_
RXD1
1
M25_ M25_ M25_ M25_ M25_
RXD6 TXD8 RXD9 RXD7 RXD8
VDD VDD
A LB_D LB_D LB_D LB_D LB_D
11
10
9
23
22
A
M25_ M25_ M25_ M25_ M25_
TXD6 TXD7 RXD3 RXD4 RXD5
A LB_D LB_D LB_D LB_D LB_D
8
7
6
21
20
B
M25_ M25_ M25_ M25_ M25_
TXD4 TXD5 RXD0 RXD1 RXD2
A LB_D LB_D LB_D LB_D LB_D
5
4
3
19
18
C
M25_ M25_ M23_ M23_ M23_
TXD2 TXD3 CRS RXD0 RXD1
A LB_D LB_D LB_D LB_D LB_D
2
1
0
17
16
D
VCC
VCC
VCC
VCC
M25_ M25_ M23_ M23_ M23_
TXD0 TXD1 TXD1 TXD0 TXEN
VCC
A M0_T M0_T M0_T M3_T M3_T M3_R M5_T M5_T M5_R M8_T M8_T M8_R M10_ M10_ M10_ M13_ M16_ M15_ M16_ M15_ M15_ M18_ M18_ M18_ M20_ M20_ M20_ M22_
E XEN XD0 XD1 XD1 XEN XD0 XD1 XEN XD0 XD1 XEN XD0 TXD1 TXEN RXD0 TXD1 TXD0 TXD1 RXD1 TXEN RXD0 TXD1 TXEN RXD0 TXD1 TXEN RXD0 RXD1
M0_R M0_R M0_C M3_T M3_C M3_R M5_T M5_C M5_R M8_T M8_C M8_R M10_ M10_ M10_ M13_ M13_ M13_ M14_ M16R M15_ M17_ M17_ M18_ M20_ M20_ M20_ M22_ M22_
AF XD1 XD0
RS
XD0
RS
XD1 XD0
RS
XD1 XD0
RS
XD1 TXD0 CRS RXD1 TXD0 CRS RXD1 CRS XD0 RXD1 RXD0 CRS RXD1 TXD0 CRS RXD1 RXD0 CRS
A M1_T M1_T M1_T M2_T M2_C M4_T M4_C M6_T M6_C M7_T M7_C M9_T M9_C M11_ M11_ M12_ M12_ M14_ M15_ M16_ M16_ M18_ M18_ M19_ M19_ M21_ M21_ M22_ M22_
RS
XD1
RS
XD1
RS
XD1
RS
XD1
RS TXD1 CRS TXD1 CRS TXD1 TXD0 TXD1 CRS TXD0 CRS TXD1 CRS TXD1 CRS TXEN TXD0
G XEN XD0 XD1 XD1
A
H
M1_R M1_C M2_T M2_R M4_T M4_R M6_T M6_R M7_T M7_R M9_T M9_R M11_ M11_ M12_ M12_ M14_ M14_ M13_ M15_ M17_ M17_ M19_ M19_ M21_ M21_ M22_
XD0
RS
XD0 XD0 XD0 XD0 XD0 XD0 XD0 XD0 XD0 XD0 TXD0 RXD0 TXD0 RXD0 TXD0 RXD0 RXD0 CRS TXD0 RXD1 TXD0 RXD0 TXD0 RXD0 TXD1
AJ
M1_R M2_T M2_R M4_T M4_R M6_T M6_R M7_T M7_R M9_T M9_R M11_ M11_ M12_ M12_ M14_ M14_ M16_ M13_ M17_ M17_ M19_ M19_ M21_ M21_
XD1 XEN XD1 XEN XD1 XEN XD1 XEN XD1 XEN XD1 TXEN RXD1 TXEN RXD1 TXEN RXD1 TXEN TXEN TXEN TXD1 TXEN RXD1 TXEN RXD1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
124
Zarlink Semiconductor Inc.
18
19
20
21
22
23
24
25
26
27
28
29
MVTX2604
15.2
Data Sheet
Ball – Signal Descriptions in Managed Mode
All pins are CMOS type; all Input Pins are 5 Volt tolerance; and all Output Pins are 3.3 CMOS drive.
15.2.1
Ball Signal Descriptions in Managed Mode
Ball No(s)
Symbol
I/O
Description
CPU BUS Interface in Managed Mode
C19, B19, A19,
C20, B20, A20,
C21, E20, A21,
B24, B22, A22,
C23, B23, A23,
C24
P_DATA[15:0]
I/O-TS with pull up
Except P_DATA[7:6]
I/O-TS with pull down
Processor Bus Data Bit [15:0].
P_DATA[7:0] is used in 8-bit mode.
C22, A24, A25
P_A[2:0]
Input
Processor Bus Address Bit [2:0]
A26
P_WE#
Input with weak
internal pull up
CPU Bus-Write Enable
B26
P_RD#
Input with weak
internal pull up
CPU Bus-Read Enable
C25
P_CS#
Input with weak
internal pull up
Chip Select
B25
P_INT#
Output
CPU Interrupt
Frame Buffer Interface
D20, B21, D19,
E19,D18, E18,
D17, E17, D16,
E16, D15, E15,
D14, E14, D13,
E13, D21, E21,
A18, B18, C18,
A17, B17, C17,
A16, B16, C16,
A15, B15, C15,
A14, B14, D9, E9,
D8, E8, D7, E7, D6,
E6, D5, E5, D4, E4,
D3, E3, D2, E2, A7,
B7, A6, B6, C6, A5,
B5, C5, A4, B4, C4,
A3, B3, C3, B2, C2
LA_D[63:0]
C14, A13, B13,
C13, A12, B12,
C12, A11, B11,
C11, D11, E11,
A10, B10, D10,
E10, A8, C7
LA_A[20:3]
I/O-TS with pullup
Output
Frame Bank A– Data Bit [63:0]
Frame Bank A – Address Bit [20:3]
125
Zarlink Semiconductor Inc.
MVTX2604
Ball No(s)
Symbol
I/O
Data Sheet
Description
B8
LA_ADSC#
Output with pull up
Frame Bank A Address Status
Control
C1
LA_CLK
Output
Frame Bank A Clock Input
C9
LA_WE#
Output with pull up
Frame Bank A Write Chip Select for
one layer SRAM configuration
D12
LA_WE0#
Output with pull up
Frame Bank A Write Chip Select for
lower layer of two layers SRAM
configuration
E12
LA_WE1#
Output with pull up
Frame Bank A Write Chip Select for
upper layer of two layers SRAM
configuration
C8
LA_OE#
Output with pull up
Frame Bank A Read Chip Select for
one bank SRAM configuration
A9
LA_OE0#
Output with pull up
Frame Bank A Read Chip Select for
lower layer of two layers SRAM
configuration
B9
LA_OE1#
Output with pull up
Frame Bank A Read Chip Select for
upper layer of two layers SRAM
configuration
F4, F5, G4, G5, H4,
H5, J4, J5, K4, K5,
L4, L5, M4, M5, N4,
N5, G3, H1, H2,
H3, J1, J2, J3, K1,
K2, K3, L1, L2, L3,
M1, M2, M3, U4,
U5, V4, V5, W4,
W5, Y4, Y5, AA4,
AA5, AB4, AB5,
AC4, AC5, AD4,
AD5, W1, Y1, Y2,
Y3, AA1, AA2, AA3,
AB1, AB2, AB3,
AC1, AC2, AC3,
AD1, AD2, AD3
LB_D[63:0]
I/O-TS with pullup.
Frame Bank B– Data Bit [63:0]
N3, N2, N1, P3, P2,
P1, R5, R4, R3, R2,
R1, T5, T4, T3, T2,
T1, W3, W2
LB_A[20:3]
Output
Frame Bank B – Address Bit [20:3]
V1
LB_ADSC#
Output with pull up
Frame Bank B Address Status
Control
G1
LB_CLK
Output with pull up
Frame Bank B Clock Input
V3
LB_WE#
Output with pull up
Frame Bank B Write Chip Select for
one layer SRAM configuration
126
Zarlink Semiconductor Inc.
MVTX2604
Ball No(s)
Symbol
I/O
Data Sheet
Description
P4
LB_WE0#
Output with pull up
Frame Bank B Write Chip Select for
lower layer of two layer SRAM
configuration
P5
LB_WE1#
Output with pull up
Frame Bank B Write Chip Select for
upper layer of two layers SRAM
configuration
V2
LB_OE#
Output with pull up
Frame Bank B Read Chip Select for
one layer SRAM configuration
U1
LB_OE0#
Output with pull up
Frame Bank B Read Chip Select for
lower layer of two layers SRAM
configuration
U2
LB_OE1#
Output with pull up
Frame Bank B Read Chip Select for
upper layer of two layers SRAM
configuration
Fast Ethernet Access Ports [23:0] RMII
R28
M_MDC
Output
MII Management Data Clock –
(Common for all MII Ports [23:0])
P28
M_MDIO
I/O-TS with pull up
MII Management Data I/O –
(Common for all MII Ports –[23:0]))
R29
M_CLKI
Input
Reference Input Clock
AC29, AE28, AJ27,
AF27, AJ25, AF24,
AH23, AE19, AF21,
AJ19, AF18, AJ17,
AJ15, AF15, AJ13,
AF12, AJ11, AJ9,
AF9, AJ7, AF6,
AJ5, AJ3, AF1
M[23:0]_RXD[1]
Input with weak
internal pull up
resistors.
Ports [23:0] – Receive Data Bit [1]
AC28, AF28, AH27,
AE27, AH25, AE24,
AF22, AF20, AE21,
AH19, AH20,
AH17, AH15,
AE15, AH13, AE12,
AH11, AH9, AE9,
AH7, AE6, AH5,
AH2, AF2
M[23:0]_RXD[0]
Input with weak
internal pull up
resistors
Ports [23:0] – Receive Data Bit [0]
127
Zarlink Semiconductor Inc.
MVTX2604
Ball No(s)
Symbol
I/O
Data Sheet
Description
AC27, AF29,
AG27, AF26,
AG25, AG23,
AF23, AG21,
AH21, AF19, AF17,
AG17, AG15,
AF14, AG13, AF11,
AG11, AG9, AF8,
AG7, AF5, AG5,
AH3, AF3
M[23:0]_CRS_DV
Input with weak
internal pull down
resistors.
Ports [23:0] – Carrier Sense and
Receive Data Valid
AD29, AG28, AJ26,
AE26, AJ24, AE23,
AJ22, AJ20, AE20,
AJ18, AJ21, AJ16,
AJ14, AE14, AJ12,
AE11, AJ10, AJ8,
AE8, AJ6, AE5,
AJ4, AG1, AE1
M[23:0]_TXEN
I/O- TS with pull up ,
slew
Ports [23:0] – Transmit Enable
Strap option for RMII/GPSI
AD27, AH28,
AG26, AE25,
AG24, AE22, AJ23,
AG20, AE18,
AG18, AE16,
AG16, AG14,
AE13, AG12,
AE10, AG10, AG8,
AE7, AG6, AE4,
AG4, AG3, AE3
M[23:0]_TXD[1]
Output, slew
Ports [23:0] – Transmit Data Bit [1]
AD28, AG29,
AH26, AF25, AH24,
AG22, AH22,
AE17, AG19,
AH18, AF16, AH16,
AH14, AF13, AH12,
AF10, AH10, AH8,
AF7, AH6, AF4,
AH4, AG2, AE2
M[23:0]_TXD[0]
Output, slew
Ports [23:0] – Transmit Data Bit [0]
GMII/TBI GiGabit Ethernet Access Ports 0 & 1
U26, U25, V26,
V25, W26, W25,
Y27, Y26, AA26,
AA25, AB26, AB25,
AC26, AC25,
AD26, AD25
M25_TXD[15:0]
Output
Transmit Data Bit [15:0]
[7:0] - GMII
[9:0] - TBI
[15:0] - 2G
T28
M25_RX_DV
Input w/ pull down
Receive Data Valid
U28
M25_RX_ER
Input w/ pull up
Receive Error
R25
M25_CRS
Input w/ pull down
Carrier Sense
128
Zarlink Semiconductor Inc.
MVTX2604
Ball No(s)
Symbol
I/O
Data Sheet
Description
U29
M25_COL
Input w/ pull up
Collision Detected
T29
M25_RXCLK
Input w/ pull up
Receive Clock
U27, V29, V28,
V27, W29, W28,
W27, Y29, Y28,
Y25, AA29, AA28,
AA27, AB29, AB28,
AB27
M25_RXD[15:0]
Input w/ pull up
Receive Data Bit [15:0]
[7:0] - GMII
[9:0] - TBI
[15:0] - 2G
T26
M25_TX_EN
Output w/ pull up
Transmit Data Enable
R26
M25_TX_ER
Output w/ pull up
Transmit Error
T27
M25_ MTXCLK
Input w/ pull down
MII Mode Transmit Clock
T25
M25_ TXCLK
Output
Gigabit Transmit Clock
P29
GREF_CLK0
Input w/ pull up
Gigabit Reference Clock
G26, G25, H26,
H25, J26, J25, K25,
K26, M25, L26,
M26, L25, N26,
N25, P26, P25
M26_TXD[15:0]
Output
Transmit Data Bit [15:0]
[7:0] - GMII
[9:0] - TBI
[15:0] - 2G
F28
M26_RX_DV
Input w/ pull down
Receive Data Valid
G28
M26_RX_ER
Input w/ pull up
Receive Error
E25
M26_CRS
Input w/ pull down
Carrier Sense
G29
M26_COL
Input w/ pull up
Collision Detected
F29
M26_RXCLK
Input w/ pull up
Receive Clock
G27,H29, H28,
H27, J29, J28, J27,
K29, K28, K27,
L29, L28, L27,
M29, M28, M27
M26_RXD[15:0]
Input w/ pull up
Receive Data Bit [15:0]
[7:0] - GMII
[9:0] - TBI
[15:0] - 2G
F26
M26_TX_EN
Output w/ pull up
Transmit Data Enable
E26
M26_TX_ER
Output w/ pull up
Transmit Error
F27
M26_ MTXCLK
Input w/ pull down
MII Mode Transmit Clock
F25
M26_ TXCLK
Output
Gigabit Transmit Clock
N29
GREF_CLK1
Input w/ pull up
Gigabit Reference Clock
C29
LED_CLK/TSTOUT0
I/O- TS with pull up
LED Serial Interface Output Clock
D29
LED_SYN/TSTOUT1
I/O- TS with pull up
LED Output Data Stream Envelope
LED Interface
129
Zarlink Semiconductor Inc.
MVTX2604
Ball No(s)
Symbol
I/O
Data Sheet
Description
E29
LED_BIT/TSTOUT2
I/O- TS with pull up
LED Serial Data Output Stream
B28
G1_RXTX#/TSTOUT
3
I/O- TS with pull up
LED for Gigabit port 1 (receive +
transmit)
C28
G1_DPCOL#/TSTO
UT4
I/O- TS with pull up
LED for Gigabit port 1 (full duplex +
collision)
D28
G1_LINK#/TSTOUT
5
I/O- TS with pull up
LED for Gigabit port 1
E28
G2_RXTX#/TSTOUT
6
I/O- TS with pull up
LED for Gigabit port 2 (receive +
transmit)
A27
G2_DPCOL#/TSTO
UT7
I/O- TS with pull up
LED for Gigabit port 2 (full duplex +
collision)
B27
G2_LINK#/TSTOUT
8
I/O- TS with pull up
LED for Gigabit port 2
C27
INIT_DONE/TSTOU
T9
I/O- TS with pull up
System start operation
D27
INIT_START/TSTOU
T10
I/O- TS with pull up
Start initialization
C26
CHECKSUM_OK/TS
TOUT11
I/O- TS with pull up
EEPROM read OK
D26
FCB_ERR/TSTOUT
12
I/O- TS with pull up
FCB memory self test fail
D25
MCT_ERR/TSTOUT
13
I/O- TS with pull up
MCT memory self test fail
D24
BIST_IN_PRC/TSTO
UT14
I/O- TS with pull up
Processing memory self test
E24
BIST_DONE/TSTOU
T15
I/O- TS with pull up
Memory self test done
U3, C10
T_MODE0,
T_MODE1
I/O-TS
Test Pins
00 – Test mode – Set Mode upon
Reset, and provides NAND Tree test
output during test mode
01 - Reserved - Do not use
10 - Reserved - Do not use
11 – Normal mode. Use external pull
up for normal mode
F3
SCAN_EN
Input with pull down
Scan Enable
E27
SCANMODE
Input with pull down
1 – Enable Test mode
0 - Normal mode (open)
Test Facility
130
Zarlink Semiconductor Inc.
MVTX2604
Ball No(s)
Symbol
Data Sheet
I/O
Description
System Clock, Power, and Ground Pins
E1
SCLK
Input
System Clock at 100 MHz
K12, K13, K17,K18
M10, N10, M20,
N20, U10, V10,
U20, V20, Y12,
Y13, Y17, Y18
VDD
Power
+2.5 Volt DC Supply
F13, F14, F15,
F16, F17, N6, P6,
R6, T6, U6, N24,
P24, R24, T24,
U24, AD13, AD14,
AD15, AD16, AD17
VCC
Power
+3.3 Volt DC Supply
M12, M13, M14,
M15, M16, M17,
M18, N12, N13,
N14, N15, N16,
N17, N18, P12,
P13, P14, P15,
P16, P17, P18,
R12, R13, R14,
R15, R16, R17,
R18, T12, T13,
T14, T15, T16,
T17, T18, U12,
U13, U14, U15,
U16, U17, U18,
V12, V13, V14,
V15, V16, V17,
V18,
VSS
Power Ground
Ground
F1
AVCC
Analog Power
Analog +2.5 Volt DC Supply
D1
AGND
Analog Ground
Analog Ground
D22
SCANCOL
Input/ output
Scans the Collision signal of Home
PHY
D23
SCANCLK
Output
Clock for scanning Home PHY
collision and link
E23
SCANLINK
Input/ output
Link up signal from Home PHY
F2
RESIN#
Input
Reset Input
G2
RESETOUT#
Output
Reset PHY
MISC
Bootstrap Pins (Default = pull up, 1= pull up 0= pull down)
After reset TSTOUT0 to TSTOU15 are used by the LED interface.
C29
TSTOUT0
Default 1
131
Zarlink Semiconductor Inc.
GIGA Link polarity
0 – active low
1 – active high
MVTX2604
Ball No(s)
Symbol
Data Sheet
I/O
Description
D29
TSTOUT1
Default 1
RMII MAC Power Saving Enable
0 – No power saving
1 – power saving
E29
TSTOUT2
Default: Enable (1)
Recommend disable
(0) with pull-down
Giga Half Duplex Support
0 - Disable
1 - Enable
B28
TSTOUT3
Default 1
Module detect enable
0 – Hot swap enable
1 – Hot swap disable
C28
TSTOUT4
Default 1
Memory is SBRAM/ZBT
0 – ZBT
1 – Pipeline SBRAM
D28
TSTOUT5
Default 1
Scan Speed: ¼ SCLK or SCLK
0 – ¼ SCLK (HPNA)
1 - SCLK
E28
TSTOUT6
Default 1
CPU Port Mode
0 - 8 bit Bus Mode
1 - 16 bit Bus Mode
A27
TSTOUT7
Default 1
Memory Size
0 - 256 K x 32 or 256 K x 64
(4 M total)
1 - 128 K x 32 or 128 K x 64
(2 M total)
B27
TSTOUT8
Default 1
EEPROM Installed
0 – EEPROM installed
1 – EEPROM not installed
C27
TSTOUT9
Default 1
MCT Aging
0 – MCT aging disable
1 – MCT aging enable
D27
TSTOUT10
Default 1
FCB Aging
0 - FCB aging disable
1 – FCB aging enable
C26
TSTOUT11
Default 1
Timeout Reset
0 – Time out reset disable
1 – Time out reset enable. Issue
reset if any state machine did not go
back to idle for 5sec.
D26
TSTOUT12
D25
TSTOUT13
Default 1
FDB RAM depth (1 or 2 layers)
0 – 2 layer
1 – 1 layer
D24
TSTOUT14
Default 1
CPU installed
0 – CPU installed
1 – CPU not installed
E24
TSTOUT15
Default 1
SRAM Test Mode
0 – Enable test mode
1 – Normal operation
Reserved
132
Zarlink Semiconductor Inc.
MVTX2604
Ball No(s)
Symbol
Data Sheet
I/O
Description
T26, R26
G0_TXEN,
G0_TXER
Default: PCS
Giga0
Mode: G0_TXEN G0_TXER
0
0
MII
0
1
2G
1
0
GMII
1
1
PCS
F26, E26
G1_TXEN,
G1_TXER
Default: PCS
Giga1
Mode: G1_TXEN G1_TXER
0
0
MII
0
1
2G
1
0
GMII
1
1
PCS
AD29, AG28, AJ26,
AE26, AJ24, AE23,
AJ22, AJ20, AE20,
AJ18, AJ21, AJ16,
AJ14, AE14, AJ12,
AE11, AJ10, AJ8,
AE8, AJ6, AE5,
AJ4, AG1, AE1
M[23:0] TXEN
Default: RMII
0 – GPSI
1 – RMII
C21
P_D[9]
Must be pulled-down
Reserved. Must be pulled-down.
C19, B19, A19
P_D[15:13]
Default: 111
Programmable delay for internal
OE_CLK from SCLK input. The
OE_CLK is used for generating the
OE0 and OE1 signals
Suggested value is 001.
C20, B20, A20
P_D[12:10]
Default: 111
Programmable delay for LA_CLK
and LB_CLK from internal OE_CLK.
The LA_CLK and LB_CLK delay
from SCLK is the sum of the delay
programmed in here and the delay in
P_D[15:13].
Suggested value is 011.
B22, A22, C23,
B23, A23, C24
P_D[5:0]
Default: 111111
Dedicated Port Mirror Mode. The
first 5 bits select the port to be
mirrored. The last bit selects either
ingress or egress data.
Notes
# = Active low signal
Input = Input signal
In-ST = Input signal with Schmitt-Trigger
Output = Output signal (Tri-State driver)
Out-OD = Output signal with Open-Drain driver
I/O-TS = Input & Output signal with Tri-State driver
I/O-OD = Input & Output signal with Open-Drain driver
133
Zarlink Semiconductor Inc.
MVTX2604
15.2.2
Data Sheet
Ball – Signal Descriptions in Unmanaged Mode
Ball No(s)
Symbol
I/O
Description
I2C Interface Note: In unmanaged mode, Use I2C and Serial control interface to configure the system
A24
SCL
Output
I2C Data Clock
A25
SDA
I/O-TS with internal pull
up
I2C Data I/O
Serial Control Interface
A26
STROBE
Input with weak internal
pull up
Serial Strobe Pin
B26
D0
Input with weak internal
pull up
Serial Data Input
C25
AUTOFD
Output with pull up
Serial Data Output (AutoFD)
Frame Buffer Interface
D20, B21, D19,
E19,D18, E18,
D17, E17, D16,
E16, D15, E15,
D14, E14, D13,
E13, D21, E21,
A18, B18, C18,
A17, B17, C17,
A16, B16, C16,
A15, B15, C15,
A14, B14, D9, E9,
D8, E8, D7, E7,
D6, E6, D5, E5,
D4, E4, D3, E3,
D2, E2, A7, B7,
A6, B6, C6, A5,
B5, C5, A4, B4,
C4, A3, B3, C3,
B2, C2
LA_D[63:0]
I/O-TS with pull up
C14, A13, B13,
C13, A12, B12,
C12, A11, B11,
C11, D11, E11,
A10, B10, D10,
E10, A8, C7
LA_A[20:3]
Output
Frame Bank A – Address Bit
[20:3]
B8
LA_ADSC#
Output with pull up
Frame Bank A Address Status
Control
C1
LA_CLK
Output with pull up
Frame Bank A Clock Input
C9
LA_WE#
Output with pull up
Frame Bank A Write Chip
Select for one layer SRAM
application
134
Zarlink Semiconductor Inc.
Frame Bank A– Data Bit [63:0]
MVTX2604
Ball No(s)
Symbol
I/O
Data Sheet
Description
D12
LA_WE0#
Output with pull up
Frame Bank A Write Chip
Select for lower layer of two
bank SRAM application
E12
LA_WE1#
Output with pull up
Frame Bank A Write Chip
Select for upper bank of two
layer SRAM application
C8
LA_OE#
Output with pull up
Frame Bank A Read Chip
Select for one layer SRAM
application
A9
LA_OE0#
Output with pull up
Frame Bank A Read Chip
Select for lower layer of two
layers SRAM application
B9
LA_OE1#
Output with pull up
Frame Bank A Read Chip
Select for upper layer of two
layers SRAM application
F4, F5, G4, G5,
H4, H5, J4, J5,
K4, K5, L4, L5,
M4, M5, N4, N5,
G3, H1, H2, H3,
J1, J2, J3, K1, K2,
K3, L1, L2, L3,
M1, M2, M3, U4,
U5, V4, V5, W4,
W5, Y4, Y5, AA4,
AA5, AB4, AB5,
AC4, AC5, AD4,
AD5, W1, Y1, Y2,
Y3, AA1, AA2,
AA3, AB1, AB2,
AB3, AC1, AC2,
AC3, AD1, AD2,
AD3
LB_D[63:0]
I/O-TS with pull up.
Frame Bank B– Data Bit [63:0]
N3, N2, N1, P3,
P2, P1, R5, R4,
R3, R2, R1, T5,
T4, T3, T2, T1,
W3, W2
LB_A[20:3]
Output
Frame Bank B – Address Bit
[20:3]
V1
LB_ADSC#
Output with pull up
Frame Bank B Address Status
Control
G1
LB_CLK
Output with pull up
Frame Bank B Clock Input
V3
LB_WE#
Output with pull up
Frame Bank B Write Chip
Select for one layer SRAM
application
135
Zarlink Semiconductor Inc.
MVTX2604
Ball No(s)
Symbol
I/O
Data Sheet
Description
P4
LB_WE0#
Output with pull up
Frame Bank B Write Chip
Select for lower layer of two
layers SRAM application
P5
LB_WE1#
Output with pull up
Frame Bank B Write Chip
Select for upper layer of two
layers SRAM application
V2
LB_OE#
Output with pull up
Frame Bank B Read Chip
Select for one layer SRAM
application
U1
LB_OE0#
Output with pull up
Frame Bank B Read Chip
Select for lower layer of two
layers SRAM application
U2
LB_OE1#
Output with pull up
Frame Bank B Read Chip
Select for upper layer of two
layers SRAM application
Fast Ethernet Access Ports [23:0] RMII
R28
M_MDC
Output
MII Management Data Clock –
(Common for all MII Ports
[23:0])
P28
M_MDIO
I/O-TS with pull up
MII Management Data I/O –
(Common for all MII Ports –
[23:0])
R29
M_CLKI
Input
Reference Input Clock
AC29, AE28,
AJ27, AF27,
AJ25, AF24,
AH23, AE19,
AF21, AJ19,
AF18, AJ17,
AJ15, AF15,
AJ13, AF12,
AJ11, AJ9, AF9,
AJ7, AF6, AJ5,
AJ3, AF1
M[23:0]_RXD[1]
Input with weak internal
pull up resistors.
Ports [23:0] – Receive Data Bit
[1]
AC28, AF28,
AH27, AE27,
AH25, AE24,
AF22, AF20,
AE21, AH19,
AH20, AH17,
AH15, AE15,
AH13, AE12,
AH11, AH9, AE9,
AH7, AE6, AH5,
AH2, AF2
M[23:0]_RXD[0]
Input with weak internal
pull up resistors
Ports [23:0] – Receive Data Bit
[0]
136
Zarlink Semiconductor Inc.
MVTX2604
Ball No(s)
Symbol
I/O
Data Sheet
Description
AC27, AF29,
AG27, AF26,
AG25, AG23,
AF23, AG21,
AH21, AF19,
AF17, AG17,
AG15, AF14,
AG13, AF11,
AG11, AG9, AF8,
AG7, AF5, AG5,
AH3, AF3
M[23:0]_CRS_DV
Input with weak internal
pull down resistors.
Ports [23:0] – Carrier Sense
and Receive Data Valid
AD29, AG28,
AJ26, AE26,
AJ24, AE23,
AJ22, AJ20,
AE20, AJ18,
AJ21, AJ16,
AJ14, AE14,
AJ12, AE11,
AJ10, AJ8, AE8,
AJ6, AE5, AJ4,
AG1, AE1
M[23:0]_TXEN
I/O- TS with pull up ,
slew
Ports [23:0] – Transmit Enable
Strap option for RMII/GPSI
AD27, AH28,
AG26, AE25,
AG24, AE22,
AJ23, AG20,
AE18, AG18,
AE16, AG16,
AG14, AE13,
AG12, AE10,
AG10, AG8, AE7,
AG6, AE4, AG4,
AG3, AE3
M[23:0]_TXD[1]
Output, slew
Ports [23:0] – Transmit Data Bit
[1]
AD28, AG29,
AH26, AF25,
AH24, AG22,
AH22, AE17,
AG19, AH18,
AF16, AH16,
AH14, AF13,
AH12, AF10,
AH10, AH8, AF7,
AH6, AF4, AH4,
AG2, AE2
M[23:0]_TXD[0]
Output, slew
Ports [23:0] – Transmit Data Bit
[0]
137
Zarlink Semiconductor Inc.
MVTX2604
Ball No(s)
Symbol
I/O
Data Sheet
Description
GMII/TBI GiGabit Ethernet Access Ports 0 & 1
U26, U25, V26,
V25, W26, W25,
Y27, Y26, AA26,
AA25, AB26,
AB25, AC26,
AC25, AD26,
AD25
M25_TXD[15:0]
Output
Transmit Data Bit [15:0]
[7:0] - GMII
[9:0] - TBI
[15:0] - 2G
T28
M25_RX_DV
Input w/ pulldown
Receive Data Valid
U28
M25_RX_ER
Input w/ pullup
Receive Error
R25
M25_CRS
Input w/ pulldown
Carrier Sense
U29
M25_COL
Input w/ pullup
Collision Detected
T29
M25_RXCLK
Input w/ pullup
Receive Clock
U27, V29, V28,
V27, W29, W28,
W27, Y29, Y28,
Y25, AA29, AA28,
AA27, AB29,
AB28, AB27
M25_RXD[15:0]
Input w/ pullup
Receive Data Bit [15:0]
[7:0] - GMII
[9:0] - TBI
[15:0] - 2G
T26
M25_TX_EN
Output w/ pullup
Transmit Data Enable
R26
M25_TX_ER
Output w/ pullup
Transmit Error
T25
M25_ TXCLK
Output
Gigabit Transmit Clock
P29
GREF_CLK0
Input w/ pullup
Gigabit Reference Clock
G26, G25, H26,
H25, J26, J25,
K25, K26, M25,
L26, M26, L25,
N26, N25, P26,
P25
M26_TXD[15:0]
Output
Transmit Data Bit [15:0]
[7:0] - GMII
[9:0] - TBI
[15:0] - 2G
F28
M26_RX_DV
Input w/ pulldown
Receive Data Valid
G28
M26_RX_ER
Input w/ pullup
Receive Error
E25
M26_CRS
Input w/ pulldown
Carrier Sense
G29
M26_COL
Input w/ pullup
Collision Detected
F29
M26_RXCLK
Input w/ pullup
Receive Clock
G27,H29, H28,
H27, J29, J28,
J27, K29, K28,
K27, L29, L28,
L27, M29, M28,
M27
M26_RXD[15:0]
Input w/ pullup
Receive Data Bit [15:0]
[7:0] - GMII
[9:0] - TBI
[15:0] - 2G
138
Zarlink Semiconductor Inc.
MVTX2604
Ball No(s)
Symbol
I/O
Data Sheet
Description
F26
M26_TX_EN
Output w/ pullup
Transmit Data Enable
E26
M26_TX_ER
Output w/ pullup
Transmit Error
F25
M26_ TXCLK
Output
Gigabit Transmit Clock
N29
GREF_CLK1
Input w/ pullup
Gigabit Reference Clock
C29
LED_CLK/TSTOUT0
I/O- TS with pull up
LED Serial Interface Output
Clock
D29
LED_SYN/TSTOUT1
I/O- TS with pull up
LED Output Data Stream
Envelope
E29
LED_BIT/TSTOUT2
I/O- TS with pull up
LED Serial Data Output Stream
B28
G1_RXTX#/TSTOUT3
I/O- TS with pull up
LED for Gigabit port 1 (receive
+ transmit)
C28
G1_DPCOL#/TSTOUT4
I/O- TS with pull up
LED for Gigabit port 1 (full
duplex + collision)
D28
G1_LINK#/TSTOUT5
I/O- TS with pull up
LED for Gigabit port 1
E28
G2_RXTX#/TSTOUT6
I/O- TS with pull up
LED for Gigabit port 2 (receive
+ transmit)
A27
G2_DPCOL#/TSTOUT7
I/O- TS with pull up
LED for Gigabit port 2 (full
duplex + collision)
B27
G2_LINK#/TSTOUT8
I/O- TS with pull up
LED for Gigabit port 2
C27
INIT_DONE/TSTOUT9
I/O- TS with pull up
System start operation
D27
INIT_START/TSTOUT10
I/O- TS with pull up
Start initialization
C26
CHECKSUM_OK/TSTOU
T11
I/O- TS with pull up
EEPROM read OK
D26
FCB_ERR/TSTOUT12
I/O- TS with pull up
FCB memory self test fail
D25
MCT_ERR/TSTOUT13
I/O- TS with pull up
MCT memory self test fail
D24
BIST_IN_PRC/TSTOUT14
I/O- TS with pull up
Processing memory self test
E24
BIST_DONE/TSTOUT15
I/O- TS with pull up
Memory self test done
C22
TRUNK0
Input w/ weak internal
pull down resistors
Trunk Port Enable in
unmanaged mode
In managed mode doesn't care
A21
TRUNK1
Input w/ weak internal
pull down resistors
Trunk Port Enable in
unmanaged mode
In managed mode doesn't care
B24
TRUNK2
Input w/ weak internal
pull down resistors
Trunk Port Enable in
unmanaged mode
In managed mode doesn't care
LED Interface
Trunk Enabale
139
Zarlink Semiconductor Inc.
MVTX2604
Ball No(s)
Symbol
Data Sheet
I/O
Description
Test Facility
U3, C10
T_MODE0, T_MODE1
I/O-TS
Test Pins
00 – Test mode – Set Mode
upon Reset, and provides
NAND Tree test output during
test mode
01 - Reserved - Do not use
10 - Reserved - Do not use
11 – Normal mode. Use
external pull up for normal
mode
F3
SCAN_EN
Input with pull down
Scan Enable
0 - Normal mode (open)
E27
SCANMODE
Input with pull down
1 – Enable Test mode
0 - Normal mode (open)
System Clock, Power, and Ground Pins
E1
SCLK
Input
System Clock at 100 MHz
K12, K13,
K17,K18 M10,
N10, M20, N20,
U10, V10, U20,
V20, Y12, Y13,
Y17, Y18
VDD
Power
+2.5 Volt DC Supply
F13, F14, F15,
F16, F17, N6, P6,
R6, T6, U6, N24,
P24, R24, T24,
U24, AD13,
AD14, AD15,
AD16, AD17
VCC
Power
+3.3 Volt DC Supply
M12, M13, M14,
M15, M16, M17,
M18, N12, N13,
N14, N15, N16,
N17, N18, P12,
P13, P14, P15,
P16, P17, P18,
R12, R13, R14,
R15, R16, R17,
R18, T12, T13,
T14, T15, T16,
T17, T18, U12,
U13, U14, U15,
U16, U17, U18,
V12, V13, V14,
V15, V16, V17,
V18,
VSS
Power Ground
Ground
140
Zarlink Semiconductor Inc.
MVTX2604
Ball No(s)
Symbol
Data Sheet
I/O
Description
F1
AVCC
Analog Power
Analog +2.5 Volt DC Supply
D1
AGND
Analog Ground
Analog Ground
D22
SCANCOL
Input
Scans the Collision signal of
Home PHY
D23
SCANCLK
Input/ output
Clock for scanning Home PHY
collision and link
E23
SCANLINK
Input
Link up signal from Home PHY
F2
RESIN#
Input
Reset Input
G2
RESETOUT#
Output
Reset PHY
E20, B25
RESERVED
N/A
Reserved Pins. Leave
unconnected.
MISC
Bootstrap Pins (Default = pull up, 1= pull up 0= pull down)
After reset TSTOUT0 to TSTOU15 are used by the LED interface.
C29
TSTOUT0
Default 1
GIGA Link polarity
0 – active low
1 – active high
D29
TSTOUT1
Default 1
RMII MAC Power Saving
Enable
0 – No power saving
1 – power saving
E29
TSTOUT2
B28
TSTOUT3
Default 1
Module detect enable
0 – Hot swap enable
1 – Hot swap disable
C28
TSTOUT4
Default 1
Memory is SBRAM/ZBT
0 – ZBT
1 – Pipeline SBRAM
D28
TSTOUT5
Default 1
Scan Speed: ¼ SCLK or SCLK
0 – ¼ SCLK (HPNA)
1 - SCLK
E28
TSTOUT6
Default 1
CPU Port Mode
0 - 8 bit Bus Mode
1 - 16 bit Bus Mode
A27
TSTOUT7
Default 1
Memory Size
0 - 256 K x 32 or 256 K x 64
(4 M total)
1 - 128 K x 32 or 128 K x 64
(2 M total)
Reserved
141
Zarlink Semiconductor Inc.
MVTX2604
Ball No(s)
Symbol
Data Sheet
I/O
Description
B27
TSTOUT8
Default 1
EEPROM Installed
0 – EEPROM installed
1 – EEPROM not installed
C27
TSTOUT9
Default 1
MCT Aging
0 – MCT aging disable
1 – MCT aging enable
D27
TSTOUT10
Default 1
FCB Aging
0 - FCB aging disable
1 – FCB aging enable
C26
TSTOUT11
Default 1
Timeout Reset
0 – Time out reset disable
1 – Time out reset enable. Issue
reset if any state machine did
not go back to idle for 5sec.
D26
TSTOUT12
D25
TSTOUT13
Default 1
FDB RAM depth (1 or 2 layers)
0 – 2 layer
1 – 1 layer
D24
TSTOUT14
Default 1
CPU installed
0 – CPU installed
1 – CPU not installed
E24
TSTOUT15
Default 1
SRAM Test Mode
0 – Enable test mode
1 – Normal operation
T26, R26
G0_TXEN, G0_TXER
Default: PCS
Giga0
Mode: G0_TXEN G0_TXER
0
0
MII
0
1
2G
1
0
GMII
1
1
PCS
F26, E26
G1_TXEN, G1_TXER
Default: PCS
Giga1
Mode: G1_TXEN G1_TXER
0
0
MII
0
1
2G
1
0
GMII
1
1
PCS
Reserved
142
Zarlink Semiconductor Inc.
MVTX2604
Ball No(s)
Symbol
Data Sheet
I/O
Description
AD29, AG28,
AJ26, AE26,
AJ24, AE23,
AJ22, AJ20,
AE20, AJ18,
AJ21, AJ16,
AJ14, AE14,
AJ12, AE11,
AJ10, AJ8, AE8,
AJ6, AE5, AJ4,
AG1, AE1,
M[23:0]_TXEN
Default: RMII
0 – GPSI
1 - RMII
C21
P_D
Must be pulled-down
Reserved. Must be pulleddown.
C19, B19, A19
OE_CLK[2:0]
Default: 111
Programmable delay for internal
OE_CLK from SCLK input. The
OE_CLK is used for generating
the OE0 and OE1 signals
Suggested value is 001.
C20, B20, A20
LA_CLK[2:0]
Default: 111
Programmable delay for
LA_CLK and LB_CLK from
internal OE_CLK. The LA_CLK
and LB_CLK delay from SCLK
is the sum of the delay
programmed in here and the
delay in P_D[15:13].
Suggested value is 011.
B22, A22,
C23, B23,
A23, C24
MIRROR[5:0]
Default: 111111
Dedicated Port Mirror Mode.
The first 5 bits select the port to
be mirrored. The last bit selects
either ingress or egress data.
Note:
# = Active low signal
Input = Input signal
In-ST = Input signal with Schmitt-Trigger
Output = Output signal (Tri-State driver)
Out-OD = Output signal with Open-Drain driver
I/O-TS = Input & Output signal with Tri-State driver
I/O-OD = Input & Output signal with Open-Drain driver
143
Zarlink Semiconductor Inc.
MVTX2604
15.3
Data Sheet
Ball – Signal Name in Unmanaged Mode
Ball No.
Signal Name
Ball No.
Signal Name
Ball No.
Signal Name
D20
LA_D[63]
D3
LA_D[19]
A9
LA_OE0#
B21
LA_D[62]
E3
LA_D[18]
B9
LA_OE1#
D19
LA_D[61]
D2
LA_D[17]
F4
LB_D[63]
E19
LA_D[60]
E2
LA_D[16]
F5
LB_D[62]
D18
LA_D[59]
A7
LA_D[15]
G4
LB_D[61]
E18
LA_D[58]
B7
LA_D[14]
G5
LB_D[60]
D17
LA_D[57]
A6
LA_D[13]
H4
LB_D[59]
E17
LA_D[56]
B6
LA_D[12]
H5
LB_D[58]
D16
LA_D[55]
C6
LA_D[11]
J4
LB_D[57]
E16
LA_D[54]
A5
LA_D[10]
J5
LB_D[56]
D15
LA_D[53]
B5
LA_D[9]
K4
LB_D[55]
E15
LA_D[52]
C5
LA_D[8]
K5
LB_D[54]
D14
LA_D[51]
A4
LA_D[7]
L4
LB_D[53]
E14
LA_D[50]
B4
LA_D[6]
L5
LB_D[52]
D13
LA_D[49]
C4
LA_D[5]
M4
LB_D[51]
E13
LA_D[48]
A3
LA_D[4]
M5
LB_D[50]
D21
LA_D[47]
B3
LA_D[3]
N4
LB_D[49]
E21
LA_D[46]
C3
LA_D[2]
N5
LB_D[48]
A18
LA_D[45]
B2
LA_D[1]
G3
LB_D[47]
B18
LA_D[44]
C2
LA_D[0]
H1
LB_D[46]
C18
LA_D[43]
C14
LA_A[20]
H2
LB_D[45]
A17
LA_D[42]
A13
LA_A[19]
H3
LB_D[44]
B17
LA_D[41]
B13
LA_A[18]
J1
LB_D[43]
C17
LA_D[40]
C13
LA_A[17]
J2
LB_D[42]
A16
LA_D[39]
A12
LA_A[16]
J3
LB_D[41]
B16
LA_D[38]
B12
LA_A[15]
K1
LB_D[40]
C16
LA_D[37]
C12
LA_A[14]
K2
LB_D[39]
A15
LA_D[36]
A11
LA_A[13]
K3
LB_D[38]
B15
LA_D[35]
B11
LA_A[12]
L1
LB_D[37]
C15
LA_D[34]
C11
LA_A[11]
L2
LB_D[36]
144
Zarlink Semiconductor Inc.
MVTX2604
Ball No.
Signal Name
Ball No.
Signal Name
Data Sheet
Ball No.
Signal Name
A14
LA_D[33]
D11
LA_A[10]
L3
LB_D[35]
B14
LA_D[32]
E11
LA_A[9]
M1
LB_D[34]
D9
LA_D[31]
A10
LA_A[8]
M2
LB_D[33]
E9
LA_D[30]
B10
LA_A[7]
M3
LB_D[32]
D8
LA_D[29]
D10
LA_A[6]
U4
LB_D[31]
E8
LA_D[28]
E10
LA_A[5]
U5
LB_D[30]
D7
LA_D[27]
A8
LA_A[4]
V4
LB_D[29]
E7
LA_D[26]
C7
LA_A[3]
V5
LB_D[28]
D6
LA_D[25]
B8
LA_DSC#
W4
LB_D[27]
E6
LA_D[24]
C1
LA_CLK
W5
LB_D[26]
D5
LA_D[23]
C9
LA_WE#
Y4
LB_D[25]
E5
LA_D[22]
D12
LA_WE0#
Y5
LB_D[24]
D4
LA_D[21]
E12
LA_WE1#
AA4
LB_D[23]
E4
LA_D[20]
C8
LA_OE#
AA5
LB_D[22]
AB4
LB_D[21]
U2
LB_OE1#
AH7
M[4]_RXD[0]
AB5
LB_D[20]
R28
MDC
AE6
M[3]_RXD[0]
AC4
LB_D[19]
P28
MDIO
AH5
M[2]_RXD[0]
AC5
LB_D[18]
R29
M_CLK
AH2
M[1]_RXD[0]
AD4
LB_D[17]
AC29
M[23]_RXD[1]
AF2
M[0]_RXD[0]
AD5
LB_D[16]
AE28
M[22]_RXD[1]
AC27
M[23]_CRS_DV
W1
LB_D[15]
AJ27
M[21]_RXD[1]
AF29
M[22]_CRS_DV
Y1
LB_D[14]
AF27
M[20]_RXD[1]
AG27
M[21]_CRS_DV
Y2
LB_D[13]
AJ25
M[19]_RXD[1]
AF26
M[20]_CRS_DV
Y3
LB_D[12]
AF24
M[18]_RXD[1]
AG25
M[19]_CRS_DV
AA1
LB_D[11]
AH23
M[17]_RXD[1]
AG23
M[18]_CRS_DV
AA2
LB_D[10]
AE19
M[16]_RXD[1]
AF23
M[17]_CRS_DV
AA3
LB_D[9]
AF21
M[15]_RXD[1]
AG21
M[16]_CRS_DV
AB1
LB_D[8]
AJ19
M[14]_RXD[1]
AH21
M[15]_CRS_DV
AB2
LB_D[7]
AF18
M[13]_RXD[1]
AF19
M[14]_CRS_DV
AB3
LB_D[6]
AJ17
M[12]_RXD[1]
AF17
M[13]_CRS_DV
AC1
LB_D[5]
AJ15
M[11]_RXD[1]
AG17
M[12]_CRS_DV
145
Zarlink Semiconductor Inc.
MVTX2604
Ball No.
Signal Name
Ball No.
Signal Name
Data Sheet
Ball No.
Signal Name
AC2
LB_D[4]
AF15
M[10]_RXD[1]
AG15
M[11]_CRS_DV
AC3
LB_D[3]
AJ13
M[9]_RXD[1]
AF14
M[10]_CRS_DV
AD1
LB_D[2]
AF12
M[8]_RXD[1]
AG13
M[9]_CRS_DV
AD2
LB_D[1]
AJ11
M[7]_RXD[1]
AF11
M[8]_CRS_DV
AD3
LB_D[0]
AJ9
M[6]_RXD[1]
AG11
M[7]_CRS_DV
N3
LB_A[20]
AF9
M[5]_RXD[1]
AG9
M[6]_CRS_DV
N2
LB_A[19]
AJ7
M[4]_RXD[1]
AF8
M[5]_CRS_DV
N1
LB_A[18]
AF6
M[3]_RXD[1]
AG7
M[4]_CRS_DV
P3
LB_A[17]
AJ5
M[2]_RXD[1]
AF5
M[3]_CRS_DV
P2
LB_A[16]
AJ3
M[1]_RXD[1]
AG5
M[2]_CRS_DV
P1
LB_A[15]
AF1
M[0]_RXD[1]
AH3
M[1]_CRS_DV
R5
LB_A[14]
AC28
M[23]_RXD[0]
AF3
M[0]_CRS_DV
R4
LB_A[13]
AF28
M[22]_RXD[0]
AD29
M[23]_TXEN
R3
LB_A[12]
AH27
M[21]_RXD[0]
AG28
M[22]_TXEN
R2
LB_A[11]
AE27
M[20]_RXD[0]
AJ26
M[21]_TXEN
R1
LB_A[10]
AH25
M[19]_RXD[0]
AE26
M[20]_TXEN
T5
LB_A[9]
AE24
M[18]_RXD[0]
AJ24
M[19]_TXEN
T4
LB_A[8]
AF22
M[17]_RXD[0]
AE23
M[18]_TXEN
T3
LB_A[7]
AF20
M[16]_RXD[0]
AJ22
M[17]_TXEN
T2
LB_A[6]
AE21
M[15]_RXD[0]
AJ20
M[16]_TXEN
T1
LB_A[5]
AH19
M[14]_RXD[0]
AE20
M[15]_TXEN
W3
LB_A[4]
AH20
M[13]_RXD[0]
AJ18
M[14]_TXEN
W2
LB_A[3]
AH17
M[12]_RXD[0]
AJ21
M[13]_TXEN
V1
LB_ADSC#
AH15
M[11]_RXD[0]
AJ16
M[12]_TXEN
G1
LB_CLK
AE15
M[10]_RXD[0]
AJ14
M[11]_TXEN
V3
LB_WE#
AH13
M[9]_RXD[0]
AE14
M[10]_TXEN
P4
LB_WE0#
AE12
M[8]_RXD[0]
AJ12
M[9]_TXEN
P5
LB_WE1#
AH11
M[7]_RXD[0]
AE11
M[8]_TXEN
V2
LB_OE#
AH9
M[6]_RXD[0]
AJ10
M[7]_TXEN
U1
LB_OE0#
AE9
M[5]_RXD[0]
AJ8
M[6]_TXEN
AE8
M[5]_TXEN
AH8
M[6]_TXD[0]
G27
M26_RXD[15]
146
Zarlink Semiconductor Inc.
MVTX2604
Ball No.
Signal Name
Ball No.
Signal Name
Data Sheet
Ball No.
Signal Name
AJ6
M[4]_TXEN
AF7
M[5]_TXD[0]
H29
M26_RXD[14]
AE5
M[3]_TXEN
AH6
M[4]_TXD[0]
H28
M26_RXD[13]
AJ4
M[2]_TXEN
AF4
M[3]_TXD[0]
H27
M26_RXD[12]
AG1
M[1]_TXEN
AH4
M[2]_TXD[0]
J29
M26_RXD[11]
AE1
M[0]_TXEN
AG2
M[1]_TXD[0]
J28
M26_RXD[10]
AD27
M[23]_TXD[1]
AE2
M[0]_TXD[0]
J27
M26_RXD[9]
AH28
M[22]_TXD[1]
U26
M25_TXD[15]
K29
M26_RXD[8]
AG26
M[21]_TXD[1]
U25
M25_TXD[14]
K28
M26_RXD[7]
AE25
M[20]_TXD[1]
V26
M25_TXD[13]
K27
M26_RXD[6]
AG24
M[19]_TXD[1]
V25
M25_TXD[12]
L29
M26_RXD[5]
AE22
M[18]_TXD[1]
W26
M25_TXD[11]
L28
M26_RXD[4]
AJ23
M[17]_TXD[1]
W25
M25_TXD[10]
L27
M26_RXD[3]
AG20
M[16]_TXD[1]
Y27
M25_TXD[9]
M29
M26_RXD[2]
AE18
M[15]_TXD[1]
Y26
M25_TXD[8]
M28
M26_RXD[1]
AG18
M[14]_TXD[1]
AA26
M25_TXD[7]
M27
M26_RXD[0]
AE16
M[13]_TXD[1]
AA25
M25_TXD[6]
G26
M26_TXD[15]
AG16
M[12]_TXD[1]
AB26
M25_TXD[5]
G25
M26_TXD[14]
AG14
M[11]_TXD[1]
AB25
M25_TXD[4]
H26
M26_TXD[13]
AE13
M[10]_TXD[1]
AC26
M25_TXD[3]
H25
M26_TXD[12]
AG12
M[9]_TXD[1]
AC25
M25_TXD[2]
J26
M26_TXD[11]
AE10
M[8]_TXD[1]
AD26
M25_TXD[1]
J25
M26_TXD[10]
AG10
M[7]_TXD[1]
AD25
M25_TXD[0]
K25
M26_TXD[9]
AG8
M[6]_TXD[1]
U27
M25_RXD[15]
K26
M26_TXD[8]
AE7
M[5]_TXD[1]
V29
M25_RXD[14]
M25
M26_TXD[7]
AG6
M[4]_TXD[1]
V28
M25_RXD[13]
L26
M26_TXD[6]
AE4
M[3]_TXD[1]
V27
M25_RXD[12]
M26
M26_TXD[5]
AG4
M[2]_TXD[1]
W29
M25_RXD[11]
L25
M26_TXD[4]
AG3
M[1]_TXD[1]
W28
M25_RXD[10]
N26
M26_TXD[3]
AE3
M[0]_TXD[1]
W27
M25_RXD[9]
N25
M26_TXD[2]
AD28
M[23]_TXD[0]
Y29
M25_RXD[8]
P26
M26_TXD[1]
AG29
M[22]_TXD[0]
Y28
M25_RXD[7]
P25
M26_TXD[0]
147
Zarlink Semiconductor Inc.
MVTX2604
Ball No.
Signal Name
Ball No.
Signal Name
Data Sheet
Ball No.
Signal Name
AH26
M[21]_TXD[0]
Y25
M25_RXD[6]
F28
M26_RX_DV
AF25
M[20]_TXD[0]
AA29
M25_RXD[5]
G28
M26_RX_ER
AH24
M[19]_TXD[0]
AA28
M25_RXD[4]
E25
M26_CRS
AG22
M[18]_TXD[0]
AA27
M25_RXD[3]
G29
M26_COL
AH22
M[17]_TXD[0]
AB29
M25_RXD[2]
F29
M26_RXCLK
AE17
M[16]_TXD[0]
AB28
M25_RXD[1]
F26
M26_TX_EN
AG19
M[15]_TXD[0]
AB27
M25_RXD[0]
E26
M26_TX_ER
AH18
M[14]_TXD[0]
R26
M25_TX_ER
F25
M26_TXCLK
AF16
M[13]_TXD[0]
T25
M25_TXCLK
E24
BIST_DONE/TSTO
UT[15]
AH16
M[12]_TXD[0]
T26
M25_TX_EN
D24
BIST_IN_PRC/TST0
UT[14]
AH14
M[11]_TXD[0]
T28
M25_RX_DV
D25
MCT_ERR/TSTOUT
[13]
AF13
M[10]_TXD[0]
U28
M25_RX_ER
D26
FCB_ERR/TSTOUT[
12]
AH12
M[9]_TXD[0]
R25
M25_CRS
C26
CHECKSUM_OK/TS
TOUT[11]
AF10
M[8]_TXD[0]
U29
M25_COL
D27
INIT_START/TSTOU
T[10]
AH10
M[7]_TXD[0]
T29
M25_RXCLK
C27
INIT_DONE/TSTOU
T[9]
B27
G2_LINK#/TSTOUT[8]
U18
VSS
N12
VSS
A27
G2_DPCOL#/TSTOUT
[7]
V12
VSS
N13
VSS
E28
G2_RXTX#/TSTOUT[
6]
V13
VSS
K17
VDD
D28
G1_LINK#/TSTOUT[5]
V14
VSS
K18
VDD
C28
G1_DPCOL#/TSTOUT
[4]
V15
VSS
M10
VDD
B28
G1_RXTX#/TSTOUT[
3]
V16
VSS
N10
VDD
E29
LED_BIT/TSTOUT[2]
V17
VSS
M20
VDD
D29
LED_SYN/TSTOUT[1]
V18
VSS
N20
VDD
C29
LED_CLK/TSTOUT[0]
N14
VSS
U10
VDD
N29
GREF_CLK1
N15
VSS
V10
VDD
148
Zarlink Semiconductor Inc.
MVTX2604
Ball No.
Signal Name
Ball No.
Signal Name
Data Sheet
Ball No.
Signal Name
P29
GREF_CLK0
N16
VSS
U20
VDD
F3
SCAN_EN
N17
VSS
V20
VDD
E1
SCLK
N18
VSS
Y12
VDD
U3
T_MODE0
P12
VSS
Y13
VDD
C10
T_MODE1
P13
VSS
Y17
VDD
B24
TRUNK2
P14
VSS
Y18
VDD
A21
TRUNK1
P15
VSS
K12
VDD
C22
TRUNK0
P16
VSS
K13
VDD
A26
STROBE
C19
OE_CLK2
M16
VSS
B26
D0
B19
OE_CLK1
M17
VSS
C25
AUTOFD
A19
OE_CLK0
M18
VSS
A24
SCL
R13
VSS
F16
VCC
A25
SDA
R14
VSS
F17
VCC
F1
AVCC
R15
VSS
N6
VCC
D1
AGND
R16
VSS
P6
VCC
D22
SCANCOL
R17
VSS
R6
VCC
E23
SCANLINK
R18
VSS
T6
VCC
E27
SCANMODE
T12
VSS
U6
VCC
N28
T13
VSS
N24
VCC
N27
T14
VSS
P24
VCC
F2
RESIN#
T15
VSS
R24
VCC
G2
RESETOUT#
T16
VSS
T24
VCC
B22
MIRROR5
T17
VSS
U24
VCC
A22
MIRROR4
T18
VSS
AD13
VCC
C23
MIRROR3
U12
VSS
AD14
VCC
B23
MIRROR2
U13
VSS
AD15
VCC
A23
MIRROR1
U14
VSS
AD16
VCC
C24
MIRROR0
U15
VSS
AD17
VCC
D23
SCANCLK
U16
VSS
F13
VCC
T27
M25_MTXCLK
U17
VSS
F14
VCC
F27
M26_MTXCLK
M12
VSS
F15
VCC
149
Zarlink Semiconductor Inc.
MVTX2604
Ball No.
Signal Name
Ball No.
Signal Name
C20
LA_CLK2
M13
VSS
B20
LA_CLK1
M14
VSS
A20
LA_CLK0
M15
VSS
C21
P_D
P17
VSS
E20
RESERVED
P18
VSS
B25
RESERVED
R12
VSS
15.4
Data Sheet
Ball No.
Signal Name
Ball – Signal Name in Managed Mode
Ball No.
Signal Name
Ball No.
Signal Name
Ball No.
Signal Name
D20
LA_D[63]
D3
LA_D[19]
A9
LA_OE0#
B21
LA_D[62]
E3
LA_D[18]
B9
LA_OE1#
D19
LA_D[61]
D2
LA_D[17]
F4
LB_D[63]
E19
LA_D[60]
E2
LA_D[16]
F5
LB_D[62]
D18
LA_D[59]
A7
LA_D[15]
G4
LB_D[61]
E18
LA_D[58]
B7
LA_D[14]
G5
LB_D[60]
D17
LA_D[57]
A6
LA_D[13]
H4
LB_D[59]
E17
LA_D[56]
B6
LA_D[12]
H5
LB_D[58]
D16
LA_D[55]
C6
LA_D[11]
J4
LB_D[57]
E16
LA_D[54]
A5
LA_D[10]
J5
LB_D[56]
D15
LA_D[53]
B5
LA_D[9]
K4
LB_D[55]
E15
LA_D[52]
C5
LA_D[8]
K5
LB_D[54]
D14
LA_D[51]
A4
LA_D[7]
L4
LB_D[53]
E14
LA_D[50]
B4
LA_D[6]
L5
LB_D[52]
D13
LA_D[49]
C4
LA_D[5]
M4
LB_D[51]
E13
LA_D[48]
A3
LA_D[4]
M5
LB_D[50]
D21
LA_D[47]
B3
LA_D[3]
N4
LB_D[49]
E21
LA_D[46]
C3
LA_D[2]
N5
LB_D[48]
A18
LA_D[45]
B2
LA_D[1]
G3
LB_D[47]
B18
LA_D[44]
C2
LA_D[0]
H1
LB_D[46]
C18
LA_D[43]
C14
LA_A[20]
H2
LB_D[45]
A17
LA_D[42]
A13
LA_A[19]
H3
LB_D[44]
150
Zarlink Semiconductor Inc.
MVTX2604
Ball No.
Signal Name
Ball No.
Signal Name
Data Sheet
Ball No.
Signal Name
B17
LA_D[41]
B13
LA_A[18]
J1
LB_D[43]
C17
LA_D[40]
C13
LA_A[17]
J2
LB_D[42]
A16
LA_D[39]
A12
LA_A[16]
J3
LB_D[41]
B16
LA_D[38]
B12
LA_A[15]
K1
LB_D[40]
C16
LA_D[37]
C12
LA_A[14]
K2
LB_D[39]
A15
LA_D[36]
A11
LA_A[13]
K3
LB_D[38]
B15
LA_D[35]
B11
LA_A[12]
L1
LB_D[37]
C15
LA_D[34]
C11
LA_A[11]
L2
LB_D[36]
A14
LA_D[33]
D11
LA_A[10]
L3
LB_D[35]
B14
LA_D[32]
E11
LA_A[9]
M1
LB_D[34]
D9
LA_D[31]
A10
LA_A[8]
M2
LB_D[33]
E9
LA_D[30]
B10
LA_A[7]
M3
LB_D[32]
D8
LA_D[29]
D10
LA_A[6]
U4
LB_D[31]
E8
LA_D[28]
E10
LA_A[5]
U5
LB_D[30]
D7
LA_D[27]
A8
LA_A[4]
V4
LB_D[29]
E7
LA_D[26]
C7
LA_A[3]
V5
LB_D[28]
D6
LA_D[25]
B8
LA_DSC#
W4
LB_D[27]
E6
LA_D[24]
C1
LA_CLK
W5
LB_D[26]
D5
LA_D[23]
C9
LA_WE#
Y4
LB_D[25]
E5
LA_D[22]
D12
LA_WE0#
Y5
LB_D[24]
D4
LA_D[21]
E12
LA_WE1#
AA4
LB_D[23]
E4
LA_D[20]
C8
LA_OE#
AA5
LB_D[22]
AB4
LB_D[21]
U2
LB_OE1#
AH7
M[4]_RXD[0]
AB5
LB_D[20]
R28
MDC
AE6
M[3]_RXD[0]
AC4
LB_D[19]
P28
MDIO
AH5
M[2]_RXD[0]
AC5
LB_D[18]
R29
M_CLK
AH2
M[1]_RXD[0]
AD4
LB_D[17]
AC29
M[23]_RXD[1]
AF2
M[0]_RXD[0]
AD5
LB_D[16]
AE28
M[22]_RXD[1]
AC27
M[23]_CRS_DV
W1
LB_D[15]
AJ27
M[21]_RXD[1]
AF29
M[22]_CRS_DV
Y1
LB_D[14]
AF27
M[20]_RXD[1]
AG27
M[21]_CRS_DV
Y2
LB_D[13]
AJ25
M[19]_RXD[1]
AF26
M[20]_CRS_DV
151
Zarlink Semiconductor Inc.
MVTX2604
Ball No.
Signal Name
Ball No.
Signal Name
Data Sheet
Ball No.
Signal Name
Y3
LB_D[12]
AF24
M[18]_RXD[1]
AG25
M[19]_CRS_DV
AA1
LB_D[11]
AH23
M[17]_RXD[1]
AG23
M[18]_CRS_DV
AA2
LB_D[10]
AE19
M[16]_RXD[1]
AF23
M[17]_CRS_DV
AA3
LB_D[9]
AF21
M[15]_RXD[1]
AG21
M[16]_CRS_DV
AB1
LB_D[8]
AJ19
M[14]_RXD[1]
AH21
M[15]_CRS_DV
AB2
LB_D[7]
AF18
M[13]_RXD[1]
AF19
M[14]_CRS_DV
AB3
LB_D[6]
AJ17
M[12]_RXD[1]
AF17
M[13]_CRS_DV
AC1
LB_D[5]
AJ15
M[11]_RXD[1]
AG17
M[12]_CRS_DV
AC2
LB_D[4]
AF15
M[10]_RXD[1]
AG15
M[11]_CRS_DV
AC3
LB_D[3]
AJ13
M[9]_RXD[1]
AF14
M[10]_CRS_DV
AD1
LB_D[2]
AF12
M[8]_RXD[1]
AG13
M[9]_CRS_DV
AD2
LB_D[1]
AJ11
M[7]_RXD[1]
AF11
M[8]_CRS_DV
AD3
LB_D[0]
AJ9
M[6]_RXD[1]
AG11
M[7]_CRS_DV
N3
LB_A[20]
AF9
M[5]_RXD[1]
AG9
M[6]_CRS_DV
N2
LB_A[19]
AJ7
M[4]_RXD[1]
AF8
M[5]_CRS_DV
N1
LB_A[18]
AF6
M[3]_RXD[1]
AG7
M[4]_CRS_DV
P3
LB_A[17]
AJ5
M[2]_RXD[1]
AF5
M[3]_CRS_DV
P2
LB_A[16]
AJ3
M[1]_RXD[1]
AG5
M[2]_CRS_DV
P1
LB_A[15]
AF1
M[0]_RXD[1]
AH3
M[1]_CRS_DV
R5
LB_A[14]
AC28
M[23]_RXD[0]
AF3
M[0]_CRS_DV
R4
LB_A[13]
AF28
M[22]_RXD[0]
AD29
M[23]_TXEN
R3
LB_A[12]
AH27
M[21]_RXD[0]
AG28
M[22]_TXEN
R2
LB_A[11]
AE27
M[20]_RXD[0]
AJ26
M[21]_TXEN
R1
LB_A[10]
AH25
M[19]_RXD[0]
AE26
M[20]_TXEN
T5
LB_A[9]
AE24
M[18]_RXD[0]
AJ24
M[19]_TXEN
T4
LB_A[8]
AF22
M[17]_RXD[0]
AE23
M[18]_TXEN
T3
LB_A[7]
AF20
M[16]_RXD[0]
AJ22
M[17]_TXEN
T2
LB_A[6]
AE21
M[15]_RXD[0]
AJ20
M[16]_TXEN
T1
LB_A[5]
AH19
M[14]_RXD[0]
AE20
M[15]_TXEN
W3
LB_A[4]
AH20
M[13]_RXD[0]
AJ18
M[14]_TXEN
W2
LB_A[3]
AH17
M[12]_RXD[0]
AJ21
M[13]_TXEN
152
Zarlink Semiconductor Inc.
MVTX2604
Ball No.
Signal Name
Ball No.
Signal Name
Data Sheet
Ball No.
Signal Name
V1
LB_ADSC#
AH15
M[11]_RXD[0]
AJ16
M[12]_TXEN
G1
LB_CLK
AE15
M[10]_RXD[0]
AJ14
M[11]_TXEN
V3
LB_WE#
AH13
M[9]_RXD[0]
AE14
M[10]_TXEN
P4
LB_WE0#
AE12
M[8]_RXD[0]
AJ12
M[9]_TXEN
P5
LB_WE1#
AH11
M[7]_RXD[0]
AE11
M[8]_TXEN
V2
LB_OE#
AH9
M[6]_RXD[0]
AJ10
M[7]_TXEN
U1
LB_OE0#
AE9
M[5]_RXD[0]
AJ8
M[6]_TXEN
AE8
M[5]_TXEN
AH8
M[6]_TXD[0]
G27
M26_RXD[15]
AJ6
M[4]_TXEN
AF7
M[5]_TXD[0]
H29
M26_RXD[14]
AE5
M[3]_TXEN
AH6
M[4]_TXD[0]
H28
M26_RXD[13]
AJ4
M[2]_TXEN
AF4
M[3]_TXD[0]
H27
M26_RXD[12]
AG1
M[1]_TXEN
AH4
M[2]_TXD[0]
J29
M26_RXD[11]
AE1
M[0]_TXEN
AG2
M[1]_TXD[0]
J28
M26_RXD[10]
AD27
M[23]_TXD[1]
AE2
M[0]_TXD[0]
J27
M26_RXD[9]
AH28
M[22]_TXD[1]
U26
M25_TXD[15]
K29
M26_RXD[8]
AG26
M[21]_TXD[1]
U25
M25_TXD[14]
K28
M26_RXD[7]
AE25
M[20]_TXD[1]
V26
M25_TXD[13]
K27
M26_RXD[6]
AG24
M[19]_TXD[1]
V25
M25_TXD[12]
L29
M26_RXD[5]
AE22
M[18]_TXD[1]
W26
M25_TXD[11]
L28
M26_RXD[4]
AJ23
M[17]_TXD[1]
W25
M25_TXD[10]
L27
M26_RXD[3]
AG20
M[16]_TXD[1]
Y27
M25_TXD[9]
M29
M26_RXD[2]
AE18
M[15]_TXD[1]
Y26
M25_TXD[8]
M28
M26_RXD[1]
AG18
M[14]_TXD[1]
AA26
M25_TXD[7]
M27
M26_RXD[0]
AE16
M[13]_TXD[1]
AA25
M25_TXD[6]
G26
M26_TXD[15]
AG16
M[12]_TXD[1]
AB26
M25_TXD[5]
G25
M26_TXD[14]
AG14
M[11]_TXD[1]
AB25
M25_TXD[4]
H26
M26_TXD[13]
AE13
M[10]_TXD[1]
AC26
M25_TXD[3]
H25
M26_TXD[12]
AG12
M[9]_TXD[1]
AC25
M25_TXD[2]
J26
M26_TXD[11]
AE10
M[8]_TXD[1]
AD26
M25_TXD[1]
J25
M26_TXD[10]
AG10
M[7]_TXD[1]
AD25
M25_TXD[0]
K25
M26_TXD[9]
AG8
M[6]_TXD[1]
U27
M25_RXD[15]
K26
M26_TXD[8]
153
Zarlink Semiconductor Inc.
MVTX2604
Ball No.
Signal Name
Ball No.
Signal Name
Data Sheet
Ball No.
Signal Name
AE7
M[5]_TXD[1]
V29
M25_RXD[14]
M25
M26_TXD[7]
AG6
M[4]_TXD[1]
V28
M25_RXD[13]
L26
M26_TXD[6]
AE4
M[3]_TXD[1]
V27
M25_RXD[12]
M26
M26_TXD[5]
AG4
M[2]_TXD[1]
W29
M25_RXD[11]
L25
M26_TXD[4]
AG3
M[1]_TXD[1]
W28
M25_RXD[10]
N26
M26_TXD[3]
AE3
M[0]_TXD[1]
W27
M25_RXD[9]
N25
M26_TXD[2]
AD28
M[23]_TXD[0]
Y29
M25_RXD[8]
P26
M26_TXD[1]
AG29
M[22]_TXD[0]
Y28
M25_RXD[7]
P25
M26_TXD[0]
AH26
M[21]_TXD[0]
Y25
M25_RXD[6]
F28
M26_RX_DV
AF25
M[20]_TXD[0]
AA29
M25_RXD[5]
G28
M26_RX_ER
AH24
M[19]_TXD[0]
AA28
M25_RXD[4]
E25
M26_CRS
AG22
M[18]_TXD[0]
AA27
M25_RXD[3]
G29
M26_COL
AH22
M[17]_TXD[0]
AB29
M25_RXD[2]
F29
M26_RXCLK
AE17
M[16]_TXD[0]
AB28
M25_RXD[1]
F26
M26_TX_EN
AG19
M[15]_TXD[0]
AB27
M25_RXD[0]
E26
M26_TX_ER
AH18
M[14]_TXD[0]
R26
M25_TX_ER
F25
M26_TXCLK
AF16
M[13]_TXD[0]
T25
M25_TXCLK
E24
BIST_DONE/TSTOUT[15]
AH16
M[12]_TXD[0]
T26
M25_TX_EN
D24
BIST_IN_PRC/TST0UT[1
4]
AH14
M[11]_TXD[0]
T28
M25_RX_DV
D25
MCT_ERR/TSTOUT[13]
AF13
M[10]_TXD[0]
U28
M25_RX_ER
D26
FCB_ERR/TSTOUT[12]
AH12
M[9]_TXD[0]
R25
M25_CRS
C26
CHECKSUM_OK/TSTOU
T[11]
AF10
M[8]_TXD[0]
U29
M25_COL
D27
INIT_START/TSTOUT[10]
AH10
M[7]_TXD[0]
T29
M25_RXCLK
C27
INIT_DONE/TSTOUT[9]
B27
G2_LINK#/TSTOUT[8]
U18
VSS
N12
VSS
A27
G2_DPCOL#/TSTOUT[7]
V12
VSS
N13
VSS
E28
G2_RXTX#/TSTOUT[6]
V13
VSS
K17
VDD
D28
G1_LINK#/TSTOUT[5]
V14
VSS
K18
VDD
C28
G1_DPCOL#/TSTOUT[4]
V15
VSS
M10
VDD
B28
G1_RXTX#/TSTOUT[3]
V16
VSS
N10
VDD
E29
LED_BIT/TSTOUT[2]
V17
VSS
M20
VDD
154
Zarlink Semiconductor Inc.
MVTX2604
Ball No.
Signal Name
Ball No.
Signal Name
Data Sheet
Ball No.
Signal Name
D29
LED_SYN/TSTOUT[1]
V18
VSS
N20
VDD
C29
LED_CLK/TSTOUT[0]
N14
VSS
U10
VDD
N29
GREF_CLK1
N15
VSS
V10
VDD
P29
GREF_CLK0
C19
P_DATA15
U20
VDD
F3
SCAN_EN
B19
P_DATA14
V20
VDD
E1
SCLK
A19
P_DATA13
Y12
VDD
U3
T_MODE0
P12
VSS
Y13
VDD
C10
T_MODE1
P13
VSS
Y17
VDD
B24
P_DATA6
P14
VSS
Y18
VDD
A21
P_DATA7
P15
VSS
K12
VDD
C22
P_A2
P16
VSS
K13
VDD
A26
P_WE
N16
VSS
M16
VSS
B26
P_RD
N17
VSS
M17
VSS
C25
P_CS
N18
VSS
M18
VSS
A24
P_A1
R13
VSS
F16
VCC
A25
P_A0
R14
VSS
F17
VCC
F1
AVCC
R15
VSS
N6
VCC
D1
AGND
R16
VSS
P6
VCC
D22
SCANCOL
R17
VSS
R6
VCC
E23
SCANLINK
R18
VSS
T6
VCC
E27
SCANMODE
T12
VSS
U6
VCC
N28
T13
VSS
N24
VCC
N27
T14
VSS
P24
VCC
F2
RESIN#
T15
VSS
R24
VCC
G2
RESETOUT#
T16
VSS
T24
VCC
B22
P_DATA5
T17
VSS
U24
VCC
A22
P_DATA4
T18
VSS
AD13
VCC
C23
P_DATA3
U12
VSS
AD14
VCC
B23
P_DATA2
U13
VSS
AD15
VCC
A23
P_DATA1
U14
VSS
AD16
VCC
C24
P_DATA0
U15
VSS
AD17
VCC
155
Zarlink Semiconductor Inc.
MVTX2604
Ball No.
Signal Name
Ball No.
Signal Name
Data Sheet
Ball No.
Signal Name
D23
SCANCLK
U16
VSS
F13
VCC
T27
M25_MTXCLK
U17
VSS
F14
VCC
F27
M26_MTXCLK
M12
VSS
F15
VCC
C20
P_DATA12
M13
VSS
B20
P_DATA11
M14
VSS
A20
P_DATA10
M15
VSS
C21
P_DATA9
P17
VSS
E20
P_DATA8
P18
VSS
B25
P_INT
R12
VSS
15.5
15.5.1
AC/DC Timing
Absolute Maximum Ratings
Storage Temperature
-65°C to +150°C
Operating Temperature
-40°C to +85°C
Maximum Junction Temperature
+125°C
Supply Voltage VCC with Respect to VSS
+3.0 V to +3.6 V
Supply Voltage VDD with Respect to VSS
+2.38 V to +2.75 V
Voltage on Input Pins
-0.5 V to (VCC + 3.3 V)
Caution: Stress above those listed may damage the device. Exposure to the Absolute Maximum Ratings for
extended periods may affect device reliability. Functionality at or above these limits is not implied.
15.5.2
DC Electrical Characteristics
VCC = 3.0 V to 3.6 V (3.3v +/- 10%)TAMBIENT = -40°C to +85°C
VDD = 2.5 V +10% - 5%
156
Zarlink Semiconductor Inc.
MVTX2604
15.5.3
Data Sheet
Recommended Operating Conditions
Symbol
Parameter Description
Min.
Typ.
Max.
Unit
fosc
Frequency of Operation
ICC
Supply Current – @ 100 MHz (VCC=3.3 V)
450
mA
IDD
Supply Current – @ 100 MHz (VDD=2.5 V)
1500
mA
VOH
Output High Voltage (CMOS)
VOL
Output Low Voltage (CMOS)
VIH-TTL
Input High Voltage (TTL 5 V tolerant)
VIL-TTL
100
MHz
2.4
V
0.4
V
VCC + 2.0
V
Input Low Voltage (TTL 5 V tolerant)
0.8
V
IIL
Input Leakage Current (0.1 V < VIN < VCC)
(all pins except those with internal pull-up/pulldown resistors)
10
µA
IOL
Output Leakage Current (0.1 V < VOUT < VCC)
10
µA
CIN
Input Capacitance
5
pF
COUT
Output Capacitance
5
pF
CI/O
I/O Capacitance
7
pF
θja
Thermal resistance with 0 air flow
11.2
C/W
θja
Thermal resistance with 1 m/s air flow
10.2
C/W
θja
Thermal resistance with 2 m/s air flow
8.9
C/W
θjc
Thermal resistance between junction and case
3.1
C/W
θjb
Thermal resistance between junction and board
6.6
C/W
2.0
157
Zarlink Semiconductor Inc.
MVTX2604
15.5.4
Data Sheet
Typical Reset & Bootstrap Timing Diagram
RESIN#
RESETOUT#
Tri-Stated
R1
R3
Bootstrap Pins
Outputs
Inputs
Outputs
R2
Figure 16 - Typical Reset & Bootstrap Timing Diagram
Symbol
Parameter
Min.
R1
Delay until RESETOUT# is tri-stated
R2
Bootstrap stabilization
R3
RESETOUT# assertion
1 µs
Typ.
Note:
10 ns
RESETOUT# state is then determined
by the external pull-up/down resistor
10 µs
Bootstrap pins sampled on rising
edge of RESIN#a
2 ms
Table 14 - Reset & Bootstrap Timing
a. The TSTOUT[8:0] pins will switch over to the LED interface functionality in 3 SCLK cycles after RESIN# goes high
158
Zarlink Semiconductor Inc.
MVTX2604
15.5.5
Data Sheet
Typical CPU Timing Diagram for a CPU Write Cycle
P_ADDR
ADDR1
ADDR0
P_CS#
TWA
at least
2 SCLKs
TWS
P_WE#
TWA
at least
2 SCLKs
TWS
TWH
TWR
Recovery Time
TDH
TDH
DATA 0
DATA to VTX2600
TWH
DATA 1
TDS
TDS
Hold time
Set up time
Figure 17 - Typical CPU Timing Diagram for a CPU Write Cycle
Description
Write Cycle
(SCLK=100 Mhz)
Symbol
Min.
(SCLK=125 Mhz)
Max.
Min.
Write Set up Time
TWS
10
10
Write Active Time
TWA
20
16
Write Hold Time
TWH
2
2
Write Recovery time
TWR
30
24
Data Set Up time
TDS
10
10
Data Hold time
TDH
2
2
159
Zarlink Semiconductor Inc.
Refer to Figure 17
Max.
At least 2 SCLK
At least 3 SCLK
MVTX2604
15.5.6
Data Sheet
Typical CPU Timing Diagram for a CPU Read Cycle
P_ADDR
ADDR1
ADDR0
P_CS#
TRA
at least
2 SCLKs
TRS
P_RD#
DATA to CPU
TRH
TRS
TRA
at least
2 SCLKs
TRR
Recovery Time
at least 3 SCLKs
DATA 0
TDV
TRH
DATA 1
TDI
Valid time
TDV
2ns
TDI
Invalid time
Figure 18 - Typical CPU Timing Diagram for a CPU Read Cycle
Description
(SCLK=100 Mhz)
(SCLK=125 Mhz)
Min.
Read Cycle
Symbol
Min.
Read Set up Time
TRS
10
10
Read Active Time
TRA
20
16
Read Hold Time
TRH
2
2
Read Recovery time
TRR
30
24
Data Valid time
TDv
10
10
Data Invalid time
TDI
6
6
15.6
15.6.1
Max.
Refer to Figure 18
Max.
At least 2 SCLK
At least 3 SCLK
Local Frame Buffer SBRAM Memory Interface
Local SBRAM Memory Interface
LA_CLK
L1
LA_D[63:0]
L2
Figure 19 - Local Memory Interface – Input Setup and Hold Timing
160
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
LA_CLK
L3-max
L3-min
LA_D[63:0]
L4-max
L4-min
LA_A[20:3]
L6-max
L6-min
LA_ADSC#
L7-max
L7-min
LA_WE[1:0]#
L8-max
L8-min
LA_OE[1:0]#
L9-max
L9-min
LA_WE#
L10-max
L10-min
LA_OE#
Figure 20 - Local Memory Interface - Output Valid Delay Timing
-100 MHz
Symbol
Parameter
Note
Min. (ns)
Max. (ns)
L1
LA_D[63:0] input set-up time
4
L2
LA_D[63:0] input hold time
1.5
L3
LA_D[63:0] output valid delay
1.5
7
CL = 25 pf
L4
LA_A[20:3] output valid delay
2
7
CL = 30 pf
L6
LA_ADSC# output valid delay
1
7
CL = 30 pf
L7
LA_WE[1:0]#output valid delay
1
7
CL = 25 pf
L8
LA_OE[1:0]# output valid delay
-1
1
CL = 25 pf
L9
LA_WE# output valid delay
1
7
CL = 25 pf
L10
LA_OE# output valid delay
1
5
CL = 25 pf
Table 15 - AC Characteristics – Local Frame Buffer SBRAM Memory Interface
161
Zarlink Semiconductor Inc.
MVTX2604
15.7
15.7.1
Data Sheet
Local Switch Database SBRAM Memory Interface
Local SBRAM Memory Interface
LB_CLK
L1
LB_D[63:0]
L2
Figure 21 - Local Memory Interface – Input Setup and Hold Timing
LB_CLK
L3-max
L3-min
LB_D[31:0]
L4-max
L4-min
LB_A[21:2]
L6-max
L6-min
LB_ADSC#
L8-max
L8-min
LB_WE[1:0]#
L9-max
L9-min
LB_OE[1:0]#
L10-max
L10-min
LB_WE#
L11-max
L11-min
LB_OE#
Figure 22 - Local Memory Interface - Output Valid Delay Timing
162
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
-100 MHz
Symbol
Parameter
Note:
Min. (ns)
Max. (ns)
L1
LB_D[63:0] input set-up time
4
L2
LB_D[63:0] input hold time
1.5
L3
LB_D[63:0] output valid delay
1.5
7
CL = 25 pf
L4
LB_A[20:3] output valid delay
2
7
CL = 30 pf
L6
LB_ADSC# output valid delay
1
7
CL = 30 pf
L8
LB_WE[1:0]#output valid delay
1
7
CL = 25 pf
L9
LB_OE[1:0]# output valid delay
-1
1
CL = 25 pf
L10
LB_WE# output valid delay
1
7
CL = 25 pf
L11
LB_OE# output valid delay
1
5
CL = 25 pf
Table 16 - AC Characteristics – Local Switch Database SBRAM Memory Interface
163
Zarlink Semiconductor Inc.
MVTX2604
15.8
15.8.1
Data Sheet
AC Characteristics
Reduced Media Independent Interface
M_CLKI
M6-max
M6-min
M[23:0]_TXEN
M7-max
M7-min
M[23:0] _TXD[1:0]
Figure 23 - AC Characteristics – Reduced Media Independent Interface
M_CLKI
M2
M[23:0]_RXD
M4
M[23:0]_CRS_DV
M3
M5
Figure 24 - AC Characteristics – Reduced Media Independent Interface
-50 MHz
Symbol
Parameter
Note
Min. (ns)
Max. (ns)
M2
M[23:0]_RXD[1:0] Input Setup Time
4
M3
M[23:0]_RXD[1:0] Input Hold Time
1
M4
M[23:0]_CRS_DV Input Setup Time
4
M5
M[23:0]_CRS_DV Input Hold Time
1
M6
M[23:0]_TXEN Output Delay Time
2
11
CL = 20 pF
M7
M[23:0]_TXD[1:0] Output Delay Time
2
11
CL = 20 pF
Table 17 - AC Characteristics – Reduced Media Independent Interface
164
Zarlink Semiconductor Inc.
MVTX2604
15.8.2
Data Sheet
Gigabit Media Independent Interface - Port A
M25_TXCLK
G12-max
G12-min
M25_TXD [15:0]
G13-max
G13-min
M25_TX_EN]
G14-max
G14-min
M25_TX_ER
Figure 25 - AC Characteristics- GMII
M25_RXCLK
G1
G2
M25_RXD[15:0]
G3
G4
M25_RX_DV
G5
G6
M25_RX_ER
G7
G8
M25_RX_CRS
Figure 26 - AC Characteristics – Gigabit Media Independent Interface
Symbol
-125 Mhz
Parameter
Min. (ns)
Max. (ns)
Note
G1
M[25]_RXD[15:0] Input Setup Times
2
G2
M[25]_RXD[15:0] Input Hold Times
1
G3
M[25]_RX_DV Input Setup Times
2
G4
M[25]_RX_DV Input Hold Times
1
G5
M[25]_RX_ER Input Setup Times
2
G6
M[25]_RX_ER Input Hold Times
1
G7
M[25]_CRS Input Setup Times
2
G8
M[25]_CRS Input Hold Times
1
G12
M[25]_TXD[15:0] Output Delay Times
1
6
CL = 20 pf
G13
M[25]_TX_EN Output Delay Times
1
6.5
CL = 20 pf
G14
M[25]_TX_ER Output Delay Times
1
6
CL = 20 pf
Table 18 - AC Characteristics – Gigabit Media Independent Interface
165
Zarlink Semiconductor Inc.
MVTX2604
15.8.3
Data Sheet
Ten Bit Interface - Port A
M25_TXCLK
TIMIN
M25_TXD [9:0]
TIMAX
Figure 27 - Gigabit TBI Interface Transmit Timing
M25_RXCLK
M25_COL
T2
T2
M25_RXD[9:0]
T3
T3
Figure 28 - Gigabit TBI Interface Receive Timing
Symbol
T1
Parameter
Min. (ns)
Max. (ns)
1
6
M25_TXD[9:0] Output Delay Time
Note
CL = 20 pf
Table 19 - Output Delay Timing
Symbol
Parameter
Min. (ns)
T2
M25_RXD[9:0] Input Setup Time
3
T3
M25_RXD[9:0] Input Hold Time
3
Ma.x (ns)
Table 20 - Input Setup Timing
15.8.4
Gigabit Media Independent Interface - Port B
M26_TXCLK
G12-max
G12-min
M26_TXD [15:0]
G13-max
G13-min
M26_TX_EN]
G14-max
G14-min
M26_TX_ER
Figure 29 - AC Characteristics- GMII
166
Zarlink Semiconductor Inc.
Note
MVTX2604
Data Sheet
M26_RXCLK
G1
G2
M26_RXD[15:0]
G3
G4
M26_RX_DV
G5
G6
M26_RX_ER
G7
G8
M26_RX_CRS
Figure 30 - AC Characteristics – Gigabit Media Independent Interface
-125 Mhz
Symbol
Parameter
Note
Min. (ns)
Max. (ns)
G1
M[26]_RXD[15:0] Input Setup Times
2
G2
M[26]_RXD[15:0] Input Hold Times
1
G3
M[26]_RX_DV Input Setup Times
2
G4
M[26]_RX_DV Input Hold Times
1
G5
M[26]_RX_ER Input Setup Times
2
G6
M[26]_RX_ER Input Hold Times
1
G7
M[26]_CRS Input Setup Times
2
G8
M[26]_CRS Input Hold Times
1
G12
M[26]_TXD[15:0] Output Delay Times
1
6
CL = 20 pf
G13
M[26]_TX_EN Output Delay Times
1
6.5
CL = 20 pf
G14
M[26]_TX_ER Output Delay Times
1
6
CL = 20 pf
Table 21 - AC Characteristics – Gigabit Media Independent Interface
15.8.5
Ten Bit Interface - Port B
M26_TXCLK
TIMIN
M26_TXD [9:0]
TIMAX
Figure 31 - Gigabit TBI Interface Transmit Timing
167
Zarlink Semiconductor Inc.
MVTX2604
Data Sheet
M26_RXCLK
M26_COL
T2
T2
M26_RXD[9:0]
T3
T3
Figure 32 - Gigabit TBI Interface Timing
Symbol
T1
Parameter
M26_TXD[9:0] Output Delay Time
Min. (ns)
Max. (ns)
1
6
Note
CL = 20 pf
Table 22 - Output Delay Timing
Symbol
Parameter
Min. (ns)
T2
M26_RXD[9:0] Input Setup Time
3
T3
M26_RXD[9:0] Input Hold Time
3
Table 23 - Input Setup Timing
168
Zarlink Semiconductor Inc.
Max. (ns)
Note
MVTX2604
15.8.6
Data Sheet
LED Interface
LED_CLK
LED_SYN
LED_BIT
LE5-max
LE5-min
LE6-max
LE6-min
Figure 33 - AC Characteristics – LED Interface
Variable FREQ.
Symbol
Parameter
Note
Min. (ns)
Max. (ns)
LE5
LED_SYN Output Valid Delay
-1
7
CL = 30 pf
LE6
LED_BIT Output Valid Delay
-1
7
CL = 30 pf
Table 24 - AC Characteristics – LED Interface
169
Zarlink Semiconductor Inc.
MVTX2604
15.8.7
Data Sheet
SCANLINK SCANCOL Output Delay Timing
SCANCLK
C5-max
C5-min
SCANLINK
C7-max
C7-min
SCANCOL
Figure 34 - SCANLINK SCANCOL Output Delay Timing
SCANCLK
C1
C2
SCANLINK
C3
C4
SCANCOL
Figure 35 - SCANLINK, SCANCOL Setup Timing
-25 MHz
Symbol
Parameter
Note
Min. (ns)
Max. (ns)
C1
SCANLINK input set-up time
20
C2
SCANLINK input hold time
2
C3
SCANCOL input setup time
20
C4
SCANCOL input hold time
1
C5
SCANLINK output valid delay
0
10
CL = 30pf
C7
SCANCOL output valid delay
0
10
CL = 30pf
Table 25 - SCANLINK, SCANCOL Timing
170
Zarlink Semiconductor Inc.
MVTX2604
15.9
Data Sheet
MDIO Input Setup and Hold Timing
MDC
D1
D2
MDIO
Figure 36 - MDIO Input Setup and Hold Timing
MDC
MDIO
D3-max
D3-min
Figure 37 - MDIO Output Delay Timing
1 MHz
Symbol
Parameter
Note:
Min. (ns)
D1
MDIO input setup time
10
D2
MDIO input hold time
2
D3
MDIO output delay time
1
Table 26 - MDIO Timing
171
Zarlink Semiconductor Inc.
Max. (ns)
20
CL = 50 pf
MVTX2604
15.9.1
Data Sheet
I2C Input Setup Timing
SCL
S2
S1
SDA
Figure 38 - I 2C Input Setup Timing
SCL
S3-max
S3-min
SDA
Figure 39 - I2C Output Delay Timing
50 KHz
Symbol
Parameter
Note
Min. (ns)
S1
SDA input setup time
20
S2
SDA input hold time
1
S3*
SDA output delay time
4 usec
Max. (ns)
6 usec
* Open Drain Output. Low to High transistor is controlled by external pullup resistor.
Table 27 - I2C Timing
172
Zarlink Semiconductor Inc.
CL = 30 pf
MVTX2604
15.9.2
Data Sheet
Serial Interface Setup Timing
STROBE
D4
D5
D1
D1
D2
D0
D2
Figure 40 - Serial Interface Setup Timing
STROBE
AutoFd
D3-max
D3-min
Figure 41 - Serial Interface Output Delay Timing
Symbol
Parameter
Min. (ns)
D1
D0 setup time
20
D2
D0 hold time
3 µs
D3
AutoFd output delay time
D4
Strobe low time
5 µs
D5
Strobe high time
5 µs
Max. (ns)
1
Table 28 - Serial Interface Timing
173
Zarlink Semiconductor Inc.
50
Note
CL = 100 pf
E1
DIMENSION
A
A1
A2
D
D1
E
E1
b
e
MIN
MAX
2.20
2.46
0.50
0.70
1.17 REF
37.70
37.30
34.50 REF
37.70
37.30
34.50 REF
0.60
0.90
1.27
553
Conforms to JEDEC MS - 034
E
e
D
D1
A2
b
NOTE:
1. CONTROLLING DIMENSIONS ARE IN MM
2. DIMENSION "b" IS MEASURED AT THE MAXIMUM SOLDER BALL DIAMETER
3. SEATING PLANE IS DEFINED BY THE SPHERICAL CROWNS OF THE SOLDER BALLS.
4. N IS THE NUMBER OF SOLDER BALLS
5. NOT TO SCALE.
6. SUBSTRATE THICKNESS IS 0.56 MM
Package Code
ISSUE
ACN
DATE
APPRD.
Previous package codes:
For more information about all Zarlink products
visit our Web Site at
www.zarlink.com
Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively “Zarlink”) is believed to be reliable.
However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such
information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or
use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual
property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in
certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink.
This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part
of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other
information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the
capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute
any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and
suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does
not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in
significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink’s conditions of sale which are available on request.
Purchase of Zarlink’s I2C components conveys a licence under the Philips I2C Patent rights to use these components in and I2C System, provided that the system
conforms to the I2C Standard Specification as defined by Philips.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright Zarlink Semiconductor Inc. All Rights Reserved.
TECHNICAL DOCUMENTATION - NOT FOR RESALE