NB669 24V, High Current Synchronous Buck Converter With LDO The Future of Analog IC Technology DESCRIPTION FEATURES The NB669 is a fully integrated high frequency synchronous rectified step-down switch mode converter with 5V fixed output voltage. It offers very compact solution to achieve 6A continuous output current and 9A peak output current over a wide input supply range with excellent load and line regulation. The NB669 operates at high efficiency over a wide output current load range. • • • • • • • • Constant-On-Time (COT) control mode provides fast transient response and eases loop stabilization. Under voltage lockout is internally set as 4.15 V. An open drain power good signal indicates the output is within its nominal voltage range. • • • • Wide 6.5V to 24V Operating Input Range 5V Fixed Output Voltage Built-in 5V, 100mA LDO with Switches 6A Continuous Output Current 9A Peak Output Current 300kHZ CLK for External Charge Pump Low RDS(ON) Internal Power MOSFETs Proprietary Switching Loss Reduction Technique Internal Soft Start Output Discharge 500kHZ Switching Frequency OCP, OVP, UVP Protection and Thermal Shutdown NB669 also provides a 5V LDO, which can be used to power the external peripheries, such as the keyboard controller in the laptop computer. A 300kHz CLK is also available; its output can be used to drive an external charge pump, generating gate drive voltage for the load switches without reducing the main converter’s efficiency. APPLICATIONS Full protection features include OCP, OVP, UVP and thermal shut down. All MPS parts are lead-free and adhere to the RoHS directive. For MPS green status, please visit MPS website under Products, Quality Assurance page. The converter requires minimum number of external components and is available in QFN16 (3mmx3mm) package. • • • • • • Laptop Computer Tablet PC Networking Systems Personal Video Recorders Flat Panel Television and Monitors Distributed Power Systems “MPS” and “The Future of Analog IC Technology” are registered trademarks of Monolithic Power Systems, Inc. TYPICAL APPLICATION NB669 Rev. 1.01 7/23/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 1 NB669, 24V, HIGH CURRENT SYNCHRONOUS BUCK CONVERTER WITH LDO ORDERING INFORMATION Part Number* Package Top Marking NB669GQ QFN16 (3mmx3mm) AEV * For Tape & Reel, add suffix –Z (e.g. NB669GQ–Z) PACKAGE REFERENCE TOP VIEW VIN AGND EN 14 13 ENLDO VCC 12 11 BST 10 1 15 SW PGND 9 SW 8 SW 2 16 SW 3 4 5 6 7 NC PG CLK LDO VOUT EXPOSED PAD ON BACKSIDE ABSOLUTE MAXIMUM RATINGS (1) Supply Voltage VIN ....................................... 24V VSW ........................................-0.3V to VIN + 0.3V VSW (30ns)...................................-3V to VIN + 4V VSW (5ns).......................................-6V to VIN+4V VBST ................................................... VSW + 5.5V VEN ............................................................... 12V Enable Current IEN(2)................................ 2.5mA All Other Pins ...............................-0.3V to +5.5V (3) Continuous Power Dissipation (TA=+25°C) QFN16……………………..….…..…………1.8W Junction Temperature...............................150°C Lead Temperature ....................................260°C Storage Temperature............... -65°C to +150°C NB669 Rev. 1.01 7/23/2013 Recommended Operating Conditions (4) Supply Voltage VIN ........................... 6.5V to 22V Output Voltage VOUT ...................................... 5V Enable Current IEN...................................... 1mA Operating Junction Temp. (TJ)..-40°C to +125°C Thermal Resistance (5) θJA θJC QFN16 (3mmx3mm) ............... 70 ...... 15... °C/W Notes: 1) Exceeding these ratings may damage the device. 2) Refer to Page 11 of Configuring the EN Control. 3) The maximum allowable power dissipation is a function of the maximum junction temperature TJ(MAX), the junction-toambient thermal resistance θJA, and the ambient temperature TA. The maximum allowable continuous power dissipation at any ambient temperature is calculated by PD(MAX)=(TJ(MAX)TA)/θJA. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Internal thermal shutdown circuitry protects the device from permanent damage. 4) The device is not guaranteed to function outside of its operating conditions. 5) Measured on JESD51-7, 4-layer PCB. www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 2 NB669, 24V, HIGH CURRENT SYNCHRONOUS BUCK CONVERTER WITH LDO ELECTRICAL CHARACTERISTICS VIN = 12V, TJ = 25°C, unless otherwise noted. Parameters Symbol Condition Min Typ Max Units 1 2 μA 220 300 μA Supply Current Supply Current (Shutdown) IIN_Shtdn Supply Current (Quiescent) IIN Supply Current (No Load) IIN Supply Current (Standby) IIN_Stby VEN = 0V VEN = 2V, VENLDO = 2V , VOUT = 5.2V VEN = 2V, VENLDO = 2V , VOUT = 5.05V, Io=0A VEN = 0V, VENLDO = 2V , ILDO = 0A 140 240 40 80 μA 120 μA MOSFET High-side Switch On Resistance HSRDS-ON 30 mΩ Low-side Switch On Resistance LSRDS-ON 15 mΩ Switch Leakage SWLKG VEN = 0V, VSW = 0V 0 1 μA 8 8.5 9.5 A 400 500 350 600 kHz ns 125 130 135 Current Limit Low-side Valley Current Limit ILIMIT Switching frequency and minimum off timer Switching Frequency Minimum Off Time(6) FSW TOFF Over-voltage and Under-voltage Protection OVP Threshold VOVP OVP Delay(6) TOVPDEL UVP Threshold 2.5 VUVP UVP Delay(6) 55 TUVPDEL 60 65 8 % VOUT_Ref μs % VOUT_Ref μs VOUT_Ref And Soft Start VOUT Ref Voltage Soft Start Time VOUT_Ref TSS 4.95 1.5 5.05 1.8 5.15 1.95 V ms VILEN VEN-HYS 1.15 1.25 100 5 0 1.25 100 1.35 V mV Enable And UVLO Enable Input Low Voltage Enable Hysteresis Enable Input Current Enable LDO Input Low Voltage Enable LDO Hysteresis NB669 Rev. 1.01 7/23/2013 IEN VENLDO VENLDO-HYS VEN = 2V VEN = 0V 1.15 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. μA 1.35 V mV 3 NB669, 24V, HIGH CURRENT SYNCHRONOUS BUCK CONVERTER WITH LDO ELECTRICAL CHARACTERISTICS (continued) VIN = 12V, TJ = 25°C, unless otherwise noted. Parameters Symbol VCC Under Voltage Lockout Threshold Rising VCC Under Voltage Lockout Threshold Hysteresis Condition Min Typ Max Units VCCVth 4.65 4.85 V VCCHYS 500 mV CLK Output CLK Output High Level Voltage CLK Output Low Level Voltage VCLKH VCLKL IVclk= -5mA IVclk= 5mA CLK Frequency FCLK TJ = 25°C 4.75 0 4.95 0.05 5.15 0.1 300 V V kHz LDO Regulator LDO Regulator LDO Load Regulation VLDO LDO Load capability Switch Rdson RSwitch 4.95 ILDO =50mA Before switch-over After switch-over ILDO =50mA 70 100 5.1 5 90 5.25 1.3 2 V % mA mA Ω 5.2 5.4 V 120 VCC Regulator VCC Regulator VCC VCC Load Regulation 5 Icc=5mA 5 % Power Good PG Rising (Good) PG Falling (Fault) PG Rising (Fault) PG Falling (Good) Power Good Lower to High Delay Power Good Sink Current Capability Power Good Leakage Current Thermal Protection Thermal Shutdown (6) Thermal Shutdown Hysteresis PGVth-Hi PGVth-Lo PGVth-Hi PGVth-Lo PGTd 95 85 115 105 0.5 % VOUT_Ref ms VPG Sink 4mA 0.4 V IPG_LEAK VPG = 3.3V 100 nA TSD 150 25 °C °C Note: 6) Guaranteed by design. NB669 Rev. 1.01 7/23/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 4 NB669, 24V, HIGH CURRENT SYNCHRONOUS BUCK CONVERTER WITH LDO PIN FUNCTIONS PIN # Name 1 VIN 2 3 PGND NC 4 PG 5 CLK 6 LDO 7 VOUT 8, 9 Exposed Pad 15, 16 SW 10 BST 11 VCC 12 ENLDO 13 EN 14 AGND NB669 Rev. 1.01 7/23/2013 Description Supply Voltage. The VIN pin supplies power for internal MOSFET and regulator. The NB669 operates from a +6.5V to +24V input rail. An input capacitor is needed to decouple the input rail. Use wide PCB traces and multiple vias to make the connection. Power Ground. Use wide PCB traces and multiple vias to make the connection. Not connected. Power good output. The output of this pin is an open drain signal and is high if the output voltage is higher than 95% of the nominal voltage. There is a delay from Vout ≥ 95% to PGOOD goes high. 300kHZ CLK output to drive the external charge pump Internal 5V LDO output. Decouple with a minimum 4.7µF ceramic capacitor as close to the pin as possible. X7R or X5R grade dielectric ceramic capacitors are recommended for their stable temperature characteristics. Once the output voltage of the Buck regulator is ready, it will switch over the LDO output to save the power loss. Output voltage sense. For the NB669, the output of the Buck regulator is fixed to 5V. VOUT pin is used to sense the output voltage of the Buck regulator, connect this pin to the output capacitor of the regulator directly. This pin also acts as the input of the 5V LDO switch over power input. Keep the VOUT sensing trace far away from the SW node. Vias should also be avoided on the VOUT sensing trace. Switch Output. Connect this pin to the inductor and bootstrap capacitor. This pin is driven up to the VIN voltage by the high-side switch during the on-time of the PWM duty cycle. The inductor current drives the SW pin negative during the off-time. The on-resistance of the low-side switch and the internal diode fixes the negative voltage. Use wide and short PCB traces to make the connection. Try to minimize the area of the SW pattern. Bootstrap. A capacitor connected between SW and BST pins is required to form a floating supply across the high-side switch driver. Internal 5V LDO output. The driver and control circuits are powered from this voltage. Decouple with a minimum 1µF ceramic capacitor as close to the pin as possible. X7R or X5R grade dielectric ceramic capacitors are recommended for their stable temperature characteristics. 100mA LDO and VCC enable pin. ENLDO is internally pulled up to high. Leave this pin open to enable the LDO. Drive it low to turn off all the regulators. Buck regulator and charge pump clock enable pin. EN is a digital input that turns the Buck regulator and CLK on or off. When the power supply of the control circuit is ready, drive EN high to turn on the Buck regulator and charge pump clock, drive it low to turn them off. Analog ground. The internal reference is referred to AGND. www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 5 NB669, 24V, HIGH CURRENT SYNCHRONOUS BUCK CONVERTER WITH LDO TYPICAL PERFORMANCE CHARACTERISTICS Performance waveforms are tested on the evaluation board of the Design Example section. VIN=12V, VOUT =5V, L=2µH, TJ=+25°C, unless otherwise noted. NB669 Rev. 1.01 7/23/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 6 NB669, 24V, HIGH CURRENT SYNCHRONOUS BUCK CONVERTER WITH LDO TYPICAL PERFORMANCE CHARACTERISTICS (continued) Performance waveforms are tested on the evaluation board of the Design Example section. VIN=12V, VOUT =5V, L=2µH, TJ=+25°C, unless otherwise noted. NB669 Rev. 1.01 7/23/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 7 NB669, 24V, HIGH CURRENT SYNCHRONOUS BUCK CONVERTER WITH LDO TYPICAL PERFORMANCE CHARACTERISTICS (continued) Performance waveforms are tested on the evaluation board of the Design Example section. VIN=12V, VOUT =5V, L=2µH, TJ=+25°C, unless otherwise noted. NB669 Rev. 1.01 7/23/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 8 NB669, 24V, HIGH CURRENT SYNCHRONOUS BUCK CONVERTER WITH LDO BLOCK DIAGRAM VCC VIN BST BSTREG Softstart POR & Reference VIN VOUT 0.6V V REF On Time One Shot VFB Gate control Logic Min off time EN SW VOUT PGND 1V SW OCP PG OVP 130% VREF Fault logic POK 95% VREF CLK CLK generator AGND UVP 60% VREF Vcc VOUT Vcc Regulator LDO Switch-over LDO Control VIN ENLDO LDO Figure 1—Functional Block Diagram NB669 Rev. 1.01 7/23/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 9 NB669, 24V, HIGH CURRENT SYNCHRONOUS BUCK CONVERTER WITH LDO OPERATION PWM Operation The NB669 is fully integrated synchronous rectified step-down switch mode converter. Constant-on-time (COT) control is employed to provide fast transient response and easy loop stabilization. At the beginning of each cycle, the high-side MOSFET (HS-FET) is turned ON when the feedback voltage (VFB) is below the reference voltage (VREF), which indicates insufficient output voltage. The ON period is determined by the output voltage and input voltage to make the switching frequency fairy constant over input voltage range. After the ON period elapses, the HS-FET is turned off, or becomes OFF state. It is turned ON again when VFB drops below VREF. By repeating operation this way, the converter regulates the output voltage. The integrated low-side MOSFET (LS-FET) is turned on when the HS-FET is in its OFF state to minimize the conduction loss. There will be a dead short between input and GND if both HS-FET and LS-FET are turned on at the same time. It’s called shoot-through. In order to avoid shoot-through, a dead-time (DT) is internally generated between HS-FET off and LSFET on, or LS-FET off and HS-FET on. An internal compensation is applied for COT control to make a more stable operation even when ceramic capacitors are used as output capacitors, this internal compensation will then improve the jitter performance without affect the line or load regulation. Heavy-Load Operation When the output current is high and the inductor current is always above zero amps, it is called continuous-conduction-mode (CCM). The CCM mode operation is shown in Figure 2 shown. When VFB is below VREF, HS-FET is turned on for a fixed interval. When the HS-FET is turned off, the LS-FET is turned on until next period. In CCM mode operation, the switching frequency is fairly constant and it is called PWM mode. Light-Load Operation With the load decrease, the inductor current decrease too. Once the inductor current touch zero, the operation is transition from continuousconduction-mode (CCM) to discontinuousconduction-mode (DCM). The light load operation is shown in Figure 3. When VFB is below VREF, HS-FET is turned on for a fixed interval which is determined by one- shot on-timer as equation 1 shown. When the HS-FET is turned off, the LS-FET is turned on until the inductor current reaches zero. In DCM operation, the VFB does not reach VREF when the inductor current is approaching zero. The LS-FET driver turns into tri-state (high Z) whenever the inductor current reaches zero. A current modulator takes over the control of LS-FET and limits the inductor current to less than -1mA. Hence, the output capacitors discharge slowly to GND through LSFET. As a result, the efficiency at light load condition is greatly improved. At light load condition, the HS-FET is not turned ON as frequently as at heavy load condition. This is called skip mode. At light load or no load condition, the output drops very slowly and the NB669 reduces the switching frequency naturally and then high efficiency is achieved at light load. Figure 2—Heavy Load Operation NB669 Rev. 1.01 7/23/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 10 NB669, 24V, HIGH CURRENT SYNCHRONOUS BUCK CONVERTER WITH LDO VS LOPE 2 VNOISE V FB V REF HS D river Jitter Figure 3—Light Load Operation Figure 5—Jitter in Skip Mode As the output current increases from the light load condition, the time period within which the current modulator regulates becomes shorter. The HS-FET is turned ON more frequently. Hence, the switching frequency increases correspondingly. The output current reaches the critical level when the current modulator time is zero. The critical level of the output current is determined as follows: IOUT = (VIN − VOUT ) × VOUT 2 × L × FSW × VIN (1) It turns into PWM mode once the output current exceeds the critical level. After that, the switching frequency stays fairly constant over the output current range. Jitter and FB Ramp Slope Jitter occurs in both PWM and skip modes when noise in the VFB ripple propagates a delay to the HS-FET driver, as shown in Figures 4 and 5. Jitter can affect system stability, with noise immunity proportional to the steepness of VFB’s downward slope. However, VFB ripple does not directly affect noise immunity. VNOISE Selecting the Output Capacitors The traditional constant-on-time control scheme is intrinsically unstable if output capacitor’s ESR is not large enough as an effective current-sense resistor. Ceramic capacitors usually can not be used as output capacitor. Figure 6 shows an equivalent circuit in PWM mode with the HS-FET off. To realize the stability, the ESR value should be chosen as follow: RESR TSW T + ON 2 ≥ 0.7 × π COUT (2) TSW is the switching period. SW L VOUT VOUT R ESR FB R CAP V S L O PE1 Figure 6—Simplified Circuit in PWM Mode VFB VREF HS D river J itter Figure 4—Jitter in PWM Mode The NB669 has built in internal ramp compensation to make sure the system is stable even without the help of output capacitor’s ESR; and thus the pure ceramic capacitor solution can be applicant. The pure ceramic capacitor solution can significantly reduce the output ripple, total BOM cost and the board area. Configuring the EN Control The NB669 has two enable pins to control the on/off of the internal regulators. ENLDO is used to enable or disable the whole NB669 Rev. 1.01 7/23/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 11 NB669, 24V, HIGH CURRENT SYNCHRONOUS BUCK CONVERTER WITH LDO chip. Once ENLDO is off, all the regulators include Vcc will be off. ENLDO is internally pulled high so it can be floated in the normal operation. When ENLDO is pulled high, Pull En high to turn on the Buck regulator also the charge pump clk, and pull EN low to turn them off. Do not float the EN pin. Especially, just using the pull-up resistor RUP (the pull-down resistor is not connected), the VIN-START is determined by input UVLO, and the minimum resistor value is: See Table1 for the logics to control the regulators A typical pull-up resistor is 499kΩ. Table 1—ENLDO/EN Control State ENLDO S0 1 S3 1 S4/S5 0 Others 0 EN 1 0 0 1 VCC VOUT/CLK ON ON ON OFF OFF OFF OFF OFF RUP + RDOWN (V) RDOWN (3) To avoid noise, a 10nF ceramic capacitor from EN to GND is recommended. There is an internal Zener diode on the EN pin, which clamps the EN pin voltage to prevent it from running away. The maximum pull up current assuming a worst case 12V internal Zener clamp should be less than 1mA. Therefore, when EN is driven by an external logic signal, the EN voltage should be lower than 12V; when EN is connected with VIN through a pull-up resistor or a resistive voltage divider, the resistance selection should ensure the maximum pull up current less than 1mA. If using a resistive voltage divider and VIN higher than 12V, the allowed minimum pull-up resistor RUP should meet the following equation: NB669 Rev. 1.01 7/23/2013 (5) The NB669 employs soft start (SS) mechanism to ensure smooth output during power-up. When the EN pin becomes high, the internal reference voltage ramps up gradually; hence, the output voltage ramps up smoothly, as well. Once the reference voltage reaches the target value, the soft start finishes and it enters into steady state operation. If the output is pre-biased to a certain voltage during startup, the IC will disable the switching of both high-side and low-side switches until the voltage on the internal reference exceeds the sensed output voltage at the internal FB node. 5V Linear Regulator For example, for RUP=150kΩ and RDOWN=51kΩ, the VIN−START is set at 5.32V. VIN (V) − 12 12 − < 1(mA) RUP (kΩ) RDOWN (kΩ) VIN (V) − 12 1(mA) Soft Start LDO ON ON OFF OFF For automatic start-up the EN pin can be pulled up to input voltage through a resistive voltage divider. Choose the values of the pull-up resistor (RUP from Vin pin to EN pin) and the pull-down resistor (RDOWN from EN pin to GND) to determine the automatic start-up voltage: VIN− START = 1.35 × RUP (kΩ) > (4) There is a built-in 100-mA standby linear regulator which outputs 5V.The 5V LDO is intended mainly for auxiliary 5V supply for the notebook system during standby mode. Add a ceramic capacitor with a value between 4.7μF and 22μF placed close to the LDO pins to stabilize LDOs. 5V LDO Switch Over When the output voltage becomes higher than 4.77V and the power good flag is generated, internal 5V LDO regulator is shut off and the LDO output is connected to Vout pin by the internal switch over MOSFET. The 20-us power good deglitch time helps a switch over without glitch. CLK for Charge Pump The 300kHz CLK signal can be used to drive an external charge pump circuit to generate approximately 12-15V DC voltage. The CLK voltage becomes available once the VIN is higher than UVLO threshold. Example of charge pump control circuit is shown in Figure 7. www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 12 NB669, 24V, HIGH CURRENT SYNCHRONOUS BUCK CONVERTER WITH LDO CLK 100nF 100nF 5V 12V/100mA 100nF 100nF 100nF In an over-current condition, the current to the load exceeds the current to the output capacitor; thus the output voltage tends to fall off. Eventually, it will end up with crossing the under voltage protection threshold and shutdown. Over/Under-Voltage Protection (OVP/UVP) PGND PGND PGND Figure 7—Charge Pump Circuit Power Good (PG) The NB669 has power-good (PG) output used to indicate whether the output voltage of the Buck regulator is ready or not. The PG pin is the open drain of a MOSFET. It should be connected to VCC or other voltage source through a resistor (e.g. 100k). After the input voltage is applied, the MOSFET is turned on so that the PG pin is pulled to GND before SS is ready. After FB voltage reaches 95% of REF voltage, the PG pin is pulled high after a delay. The PG delay time is 0.5ms. When the FB voltage drops to 85% of REF voltage, the PG pin will be pulled low. Over Current Protection NB669 has cycle-by-cycle over current limiting control. The current-limit circuit employs a "valley" current-sensing algorithm. The part uses the Rds(on) of the low side MOSFET as a current-sensing element. If the magnitude of the current-sense signal is above the current-limit threshold, the PWM is not allowed to initiate a new cycle. The trip level is fixed internally. The inductor current is monitored by the voltage between GND pin and SW pin. GND is used as the positive current sensing node so that GND should be connected to the source terminal of the bottom MOSFET. Since the comparison is done during the high side MOSFET OFF and low side MOSFET ON state, the OC trip level sets the valley level of the inductor current. Thus, the load current at overcurrent threshold, IOC, can be calculated as follows: IOC = I _ limit + NB669 Rev. 1.01 7/23/2013 ΔIinductor 2 NB669 monitors output voltage to detect over and under voltage. When the feedback voltage becomes higher than 115% of the target voltage, the controller will enter Dynamic Regulation Period. During this period, the LS will off when the LS current goes to -1A, this will then discharge the output and try to keep it within the normal range. If the dynamic regulation can not limit the increasing of the Vo, once the feedback voltage becomes higher than 130% of the feedback voltage, the OVP comparator output goes high and the circuit latches as the high-side MOSFET driver OFF and the low-side MOSFET driver turn on acting as an -1A current source. When the feedback voltage becomes lower than 60% of the target voltage, the UVP comparator output goes high if the UV still occurs after 26us delay; then the fault latch will be triggered--latches HS off and LS on; the LS FET keeps on until the inductor current goes zero. UVLO Protection The NB669 has under-voltage lock-out protection (UVLO). When the VCC voltage is higher than the UVLO rising threshold voltage, the part will be powered up. It shuts off when the VIN voltage is lower than the UVLO falling threshold voltage. This is non-latch protection. The part is disabled when the VCC voltage falls below 4.65V. If an application requires a higher under-voltage lockout (UVLO), use the EN pin as shown in Figure 8 to adjust the input voltage UVLO by using two external resistors. It is recommended to use the enable resistors to set the UVLO falling threshold (VSTOP) above 4.65V. The rising threshold (VSTART) should be set to provide enough hysteresis to allow for any input supply variations. (6) www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 13 NB669, 24V, HIGH CURRENT SYNCHRONOUS BUCK CONVERTER WITH LDO VIN RUP NB669 EN Comparator EN RDOWN Figure 8—Adjustable UVLO Thermal Shutdown Thermal shutdown is employed in the NB669. The junction temperature of the IC is internally monitored. If the junction temperature exceeds the threshold value (typical 150ºC), the converter shuts off. This is a non-latch protection. There is about 25ºC hysteresis. Once the junction temperature drops to about 125ºC, it initiates a SS. Output Discharge NB669 discharges the output when EN is low, or the controller is turned off by the protection functions (UVP & OCP, OCP, OVP, UVLO, and thermal shutdown). The part discharges outputs using an internal 6Ω MOSFET. NB669 Rev. 1.01 7/23/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 14 NB669, 24V, HIGH CURRENT SYNCHRONOUS BUCK CONVERTER WITH LDO APPLICATION INFORMATION ΔVOUT = Input Capacitor The input current to the step-down converter is discontinuous and therefore requires a capacitor to supply the AC current to the step-down converter while maintaining the DC input voltage. Ceramic capacitors are recommended for best performance and should be placed as close to the VIN pin as possible. Capacitors with X5R and X7R ceramic dielectrics are recommended because they are fairly stable with temperature fluctuations. The capacitors must also have a ripple current rating greater than the maximum input ripple current of the converter. The input ripple current can be estimated as follows: ICIN = IOUT × VOUT V × (1 − OUT ) VIN VIN (7) The worst-case condition occurs at VIN = 2VOUT, where: ICIN = IOUT 2 (8) For simplification, choose the input capacitor with an RMS current rating greater than half of the maximum load current. The input capacitance value determines the input voltage ripple of the converter. If there is an input voltage ripple requirement in the system, choose the input capacitor that meets the specification. The input voltage ripple can be estimated as follows:: ΔVIN = IOUT V V × OUT × (1 − OUT ) FSW × CIN VIN VIN (9) Under worst-case conditions where VIN = 2VOUT: ΔVIN = IOUT 1 × 4 FSW × CIN (10) Output Capacitor The output capacitor is required to maintain the DC output voltage. Ceramic or POSCAP capacitors are recommended. The output voltage ripple can be estimated as: NB669 Rev. 1.01 7/23/2013 VOUT V 1 × (1 − OUT ) × (RESR + ) (11) FSW × L VIN 8 × FSW × COUT In the case of ceramic capacitors, the impedance at the switching frequency is dominated by the capacitance. The output voltage ripple is mainly caused by the capacitance. For simplification, the output voltage ripple can be estimated as: ΔVOUT = VOUT V × (1 − OUT ) 2 8 × FSW × L × COUT VIN (12) In the case of POSCAP capacitors, the ESR dominates the impedance at the switching frequency. The ramp voltage generated from the ESR is high enough to stabilize the system. Therefore, an external ramp is not needed. A minimum ESR value around 12mΩ is required to ensure stable operation of the converter. For simplification, the output ripple can be approximated as: ΔVOUT = VOUT V × (1 − OUT ) × RESR FSW × L VIN (13) Maximum output capacitor limitation should be also considered in design application. NB669 has an around 1.8ms soft-start time period. If the output capacitor value is too high, the output voltage can’t reach the design value during the soft-start time, and then it will fail to regulate. The maximum output capacitor value CO_MAX can be limited approximately by: CO _ MAX = (ILIM _ AVG − IOUT ) × Tss / VOUT (14) Where, ILIM_AVG is the average start-up current during soft-start period. Tss is the soft-start time. Inductor The inductor is necessary to supply constant current to the output load while being driven by the switched input voltage. A larger-value inductor will result in less ripple current that will result in lower output ripple voltage. However, a larger-value inductor will have a larger physical footprint, higher series resistance, and/or lower saturation current. A good rule for determining the inductance value is to design the peak-topeak ripple current in the inductor to be in the range of 30% to 40% of the maximum output www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 15 NB669, 24V, HIGH CURRENT SYNCHRONOUS BUCK CONVERTER WITH LDO current, and that the peak inductor current is below the maximum switch current limit. The inductance value can be calculated by: 2. Put the input capacitors as close to the IN and GND pins as possible. Where ΔIL is the peak-to-peak inductor ripple current. 3. Put the decoupling capacitor as close to the VCC and AGND pins as possible. Place the Cap close to AGND if the distance is long. And place >3 Vias if via is required to reduce the leakage inductance. The inductor should not saturate under the maximum inductor peak current, where the peak inductor current can be calculated by: 4. Keep the VOUT sensing trace far away from the SW node.Vias should also be avoided on the VOUT sensing trace. L= VOUT V × (1 − OUT ) FSW × ΔIL VIN ILP = IOUT + VOUT V × (1 − OUT ) 2FSW × L VIN (15) (16) PCB Layout Guide The following guidelines should be followed when designing the PC board for the NB669: 1. The high current paths (GND, IN, and SW) should be placed very close to the device with short, direct and wide traces. 5. Keep the BST voltage path (BST, C3, and SW) as short as possible. 6. Keep the IN and GND pads connected with large copper and use at least two layers for IN and GND trace to achieve better thermal performance. Also, add several Vias with 10mil_drill/18mil_copper_width close to the IN and GND pads to help on thermal dissipation. 7. AGND connects PGND with KELVIN Connecting. 8. Four-layer layout is strongly recommended to achieve better thermal performance. Note: Please refer to the PCB Layout Application Note for more details. NB669 Rev. 1.01 7/23/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 16 NB669, 24V, HIGH CURRENT SYNCHRONOUS BUCK CONVERTER WITH LDO AGND KELVIN CONNECT TO PGND 14 EN ENLDO AGND 13 12 11 10 SW VIN 1 9 15 2 16 4 5 6 PG CLK LDO 7 VOUT VOUT 3 8 VOUT GND DO NOT CONNECT TO AGND HERE Figure 9—Recommend Layout Recommend Design Example A typical application schematic is shown in Figure 10 when large ESR caps are used, and Figure 11 shows the schematic when low ESR caps are applied. The typical performance and NB669 Rev. 1.01 7/23/2013 circuit waveforms have been shown in the Typical Performance Characteristics section. For more possible applications of this device, please refer to related Evaluation Board Datasheets. www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 17 NB669, 24V, HIGH CURRENT SYNCHRONOUS BUCK CONVERTER WITH LDO TYPICAL APPLICATION Figure 10---Typical Application Circuit with Poscap NB669 VIN=6.5-22V, VOUT=5V, IOUT=6A, FSW=500kHz Figure 11---Typical Application Circuit with Low ESR Ceramic Capacitor NB669 VIN=6.5-22V, VOUT=5V, IOUT=6A, FSW=500kHz NB669 Rev. 1.01 7/23/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 18 NB669, 24V, HIGH CURRENT SYNCHRONOUS BUCK CONVERTER WITH LDO PACKAGE INFORMATION QFN16 (3X3mm) PIN 1 ID MARKING PIN 1 ID 0.10x45 癟 YP. PIN 1 ID INDEX AREA TOP VIEW BOTTOM VIEW SIDE VIEW NOTE: 0.10x45° 1) ALL DIMENSIONS ARE IN MILLIMETERS. 2) EXPOSED PADDLE SIZE DOES NOT INCLUDE MOLD FLASH . 3) LEAD COPLANARITY SHALL BE 0.10 MILLIMETERS MAX. 4) JEDEC REFERENCE IS MO-220. 5) DRAWING IS NOT TO SCALE . RECOMMENDED LAND PATTERN NOTICE: The information in this document is subject to change without notice. Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS products into any application. MPS will not assume any legal responsibility for any said applications. NB669 Rev. 1.01 7/23/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 19