NCP1589A, NCP1589B Product Preview Low Voltage Synchronous Buck Controller The NCP1589A/B is a low cost PWM controller designed to operate from a 5 V or 12 V supply. This device is capable of producing an output voltage as low as 0.8 V. This device is capable of converting voltage from as low as 2.5 V. This 10−pin device provides an optimal level of integration to reduce size and cost of the power supply. Features include a 1.5 A gate driver design and an internally set 300 kHz or 600 kHz oscillator. In addition to the 1.5 A gate drive capability, other efficiency enhancing features of the gate driver include adaptive non−overlap circuitry. The NCP1589A/B also incorporates an externally compensated error amplifier. Protection features include programmable short circuit protection and undervoltage lockout (UVLO). Features • • • • • • • • • • • VCC Range from 4.5 V to 13.2 V 300 kHz and 600 kHz Internal Oscillator Boost Pin Operates to 30 V Voltage Mode PWM Control Precision 0.8 V Internal Reference Adjustable Output Voltage Internal 1.5 A Gate Drivers 80% Max Duty Cycle Input Under Voltage Lockout Programmable Current Limit This is a Pb−Free Device http://onsemi.com MARKING DIAGRAMS 1589x ALYWG G DFN10 CASE 485C 1589x = Specific Device Code x = A or B = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Device A L Y W G (Note: Microdot may be in either location) PIN CONNECTIONS 1 10 LX 2 9 VOS UG 3 8 FB LG 4 7 COMP/EN GND 5 6 VCC Applications • • • • • PGOOD BOOT (Top View) Graphics Cards Desktop Computers Servers / Networking DSP & FPGA Power Supply DC−DC Regulator Modules ORDERING INFORMATION Device Package Shipping† DFN10 (Pb−Free) 3000 / Tape & Reel NCP1589AMNTWG NCP1589BMNTWG NCP1589AMNTXG NCP1589BMNTXG †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. This document contains information on a product under development. ON Semiconductor reserves the right to change or discontinue this product without notice. © Semiconductor Components Industries, LLC, 2009 May, 2009 − Rev. P4 1 Publication Order Number: NCP1589A/D NCP1589A, NCP1589B VIN = 2.5 V − 13.2 V 3x22mF VBST = 4.5 V − 15 V 1500mF VCC = 4.5 V − 13.2 V 1mF 2x0.22mF 1500mF 0.1mF COMP/EN UG R2 17.08kW FB LG GND VOS R1 4.12kW R3 74.2W R9 R10 VOUT 1.65 V 1mH 2x1800mF 4.7nF 1.02k C3 0.014mF 1.02k R4 3.878kW NTD4806 LX C2 0.007mF ROCSET C1 0.0015mF 2.2 BOOT NTD4809 VCC PGOOD GND Figure 1. Typical Application Diagram PGOOD PGOOD MONITOR OV and UV VOS 9 0.8 V (Vref) ±10% of Vref ±25% of Vref POR UVLO 8 − + + − 0.8 V (Vref) + LATCH FAULT FB 10 S PWM OUT Q + COMP/EN 7 1 BOOT 3 UG 2 LX 4 LG 5 GND − CLOCK RAMP VCC VOCP − FAULT R 6 + SOFT START − OSC OSC FAULT Figure 2. Detailed Block Diagram http://onsemi.com 2 2V VCC NCP1589A, NCP1589B PIN FUNCTION DESCRIPTION Pin No. Symbol Description 1 BOOT Supply rail for the floating top gate driver. To form a boost circuit, use an external diode to bring the desired input voltage to this pin (cathode connected to BOOT pin). Connect a capacitor (CBOOT) between this pin and the LX pin. Typical values for CBOOT range from 0.1 mF to 1 mF. Ensure that CBOOT is placed near the IC. 2 LX Switch node pin. This is the reference for the floating top gate driver. Connect this pin to the source of the top MOSFET. 3 UG Top gate MOSFET driver pin. Connect this pin to the gate of the top N−channel MOSFET. 4 LG Bottom gate MOSFET driver pin. Connect this pin to the gate of the bottom N−channel MOSFET. 5 GND IC ground reference. All control circuits are referenced to this pin. 6 VCC Supply rail for the internal circuitry. Operating supply range is 4.5 V to 13.2 V. Decouple with a 1 mF capacitor to GND. Ensure that this decoupling capacitor is placed near the IC. 7 COMP/EN Compensation Pin. This is the output of the error amplifier (EA) and the non−inverting input of the PWM comparator. Use this pin in conjunction with the FB pin to compensate the voltage−control feedback loop. Pull this pin low for disable. 8 FB 9 VOS 10 PGOOD This pin is the inverting input to the error amplifier. Use this pin in conjunction with the COMP pin to compensate the voltage−control feedback loop. Connect this pin to the output resistor divider (if used) or directly to Vout. Voltage Offset Sense Power Good output. Pulled Low if VOS is ±10% of 0.8 V Vref. ABSOLUTE MAXIMUM RATINGS Pin Name Symbol VMAX VMIN VCC 15 V −0.3 V BOOT 35 V wrt/GND 40 V < 100 ns 15 V wrt/LX −0.3 V −0.3 V −0.3 V Switching Node (Bootstrap Supply Return) LX 35 V 40 V for < 100 ns −5 V −10 V for < 200 ns High−Side Driver Output (Top Gate) UG 30 V wrt/GND 15 V wrt/LX 40 V for < 100 ns −0.3 V wrt/LX −2 V for < 200 ns Low−Side Driver Output (Bottom Gate) LG VCC + 0.3 V −0.3 V −5 V for < 200 ns FB, VOS 5.0 V −0.3 V COMP/EN 3.6 V −0.3 V PGOOD 7V −0.3 V Symbol Value Unit Thermal Resistance, Junction−to−Ambient RqJA 165 °C/W Thermal Resistance, Junction−to−Case RqJC 45 °C/W Operating Junction Temperature Range TJ 0 to 150 °C Operating Ambient Temperature Range TA 0 to 70 °C Storage Temperature Range Tstg −55 to +150 °C Moisture Sensitivity Level MSL 1 − Main Supply Voltage Input Bootstrap Supply Voltage Input Feedback, VOS COMP/EN PGOOD MAXIMUM RATINGS Rating Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. This device is ESD sensitive. Use standard ESD precautions when handling. http://onsemi.com 3 NCP1589A, NCP1589B ELECTRICAL CHARACTERISTICS (0°C < TA < 70°C; 4.5 V < [BST−PHASE] < 13.2 V, 4.5 V < BST < 30 V, 0 V < PHASE < 21 V, CTG = CBG = 1.0 nF, for min/max values unless otherwise noted.) Conditions Max Unit 4.5 13.2 V 13.2 V wrt LX 4.5 30 V VFB = 1.0 V, No Switching, VCC = 13.2 V 1.0 8.0 mA VFB = 1.0 V, No Switching 0.1 100 mA UVLO Threshold VCC Rising 3.8 4.0 4.2 V UVLO Threshold VCC Falling 3.4 3.6 3.8 V UVLO Hysteresis VCC Rising or VCC Falling Characteristic Input Voltage Range Boost Voltage Range Min Typ Supply Current Quiescent Supply Current (NCP1589A) Boost Quiescent Current Undervoltage Lockout 0.4 V Switching Regulator 0.8 0.8064 V Oscillator Frequency (NCP1589A) 270 300 330 kHz Oscillator Frequency (NCP1589B) TBD 600 TBD kHz VFB Feedback Voltage (FB Tied to Comp. Measure FB Pin.) 0.7936 Ramp−Amplitude Voltage Minimum Duty Cycle Maximum Duty Cycle 70 LG Minimum on Time 1.1 V 0 % 75 80 500 % ns Error Amplifier Open Loop DC Gain (Note 1) 70 Output Source Current Output Sink Current Vfb < 0.8 V Vfb > 0.8 V Input Offset Voltage (Note 1) 80 dB 2.0 2.0 −2.0 Input Bias Current Unity Gain Bandwidth (Note 1) 15 Disable Threshold 0.6 Output Source Current During Disable mA 0 2.0 mV 0.1 1.0 mA Mhz 0.8 10 V 40 mA Gate Drivers Upper Gate Source VCC = 5 V, VUG − VLX = 2.5 V 1.5 Upper Gate Sink A 1.4 Lower Gate Source W 1.5 Lower Gate Sink VCC = 12 V A 1.0 W UG Falling to LG Rising Delay VCC = 12 V, UG−LX < 2.0 V, LG > 2.0 V 12.4 18 ns LG Falling to UG Rising Delay VCC = 12 V, LG < 2.0 V, UG > 2.0 V 12.4 18 ns Soft−Start Soft−Start time 3.0 7.0 ms Power Good Output Voltage OVP Threshold to PGOOD Output Low OVP Threshold to Part Disable 0.4 V Ramp VOS from 0.7 to 1.2. Monitor when PGOOD goes Low Logic Low, Sinking 4 mA 0.88 1.0 V Ramp VOS from 0.8 to 1.2. Monitor when outputs disable 1.0 1.2 V UVP Threshold to PGOOD Output Low Ramp VOS from 800 mV to 500 mV. Monitor when PGOOD goes Low 0.65 0.72 V UVP Threshold to Part Disable Ramp VOS from 800 mV to 500 mV. Monitor when utputs stop switching 0.5 0.6 V Sourced from LG pin, before SS 9.0 10 Overcurrent Protection OC Current Source (Note 1) 1. Guaranteed by design but not tested in production. http://onsemi.com 4 11 mA NCP1589A, NCP1589B TYPICAL CHARACTERISTICS 303 808 806 Vref, REFERENCE (mV) FSW, FREQUENCY (kHz) VCC = 12 V VCC = 5 V 302 301 300 804 802 800 798 796 794 299 0 10 20 30 40 50 60 792 70 0 TJ, JUNCTION TEMPERATURE (°C) Figure 3. Oscillator Frequency (FSW) vs. Temperature 40 60 80 Figure 4. Reference Voltage (Vref) vs. Temperature 543 5.3 OCP THRESHOLD (mV) NCP1589B 5.0 4.7 ICC (mA) 20 TJ, JUNCTION TEMPERATURE (°C) NCP1589A 4.4 4.1 542 541 540 3.8 3.5 0 20 40 60 539 0 80 20 40 60 TJ, JUNCTION TEMPERATURE (°C) TJ, JUNCTION TEMPERATURE (°C) Figure 5. ICC vs. Temperature Figure 6. OCP Threshold at 55k vs. Temperature http://onsemi.com 5 80 NCP1589A, NCP1589B APPLICATIONS INFORMATION Over Current Protection (OCP) the under voltage lockout threshold, or if the NCP1589A/B is disabled by having the COMP pin pulled low. The NCP1589A/B monitors the voltage drop across the low side mosfet and uses this information to determine if there is excessive output current. The voltage across the low side mosfet is measured from the LX pin, and is referenced to ground. The over current measurement is timed to occur at the end of the low side mosfet conduction period, just before the bottom mosfet is turned off. If the voltage drop across the bottom mosfet exceeds the over current protection threshold, then an internal counter is incremented. If the voltage drop does not exceed the over current protection threshold, then the internal counter is reset. The NCP1589A/B will latch the over current protection fault condition only if the over current protection threshold is exceeded for four consecutive cycles. When the NCP1589A/B latches an over current protection fault, both the high side and low side mosfets are turned off. To reset the over current protection fault, the power to the VCC pin must be cycled. The over current threshold voltage can be externally, by varying the value of the ROCSET resistor. The ROCSET resistor is a resistor connected between the LG pin (low side mosfet gate) and ground. During startup, after the VCC and BOOT pins reach the under voltage lock out threshold, the NCP1589A/B will source 10 mA of current out of the LG pin. This current will flow through the ROCSET resistor and produce a voltage that is sampled and then used as the over current protection threshold voltage. For example, if ROCSET is set to 10 kW, the 10 mA of current will yield a 100 mV threshold, and if the voltage drop across the low side mosfet exceeds 100 mV at the end of its conduction period, then an over current event will be detected. If the ROCSET resistor is not present, then the over current protection threshold will max out at 640 mV. The valid range for ROCSET is 5 kW to 55 kW which yields a threshold voltage range of 50 mV to 550 mV. Startup into a Precharged Load During a startup and soft start sequence the NCP1589A will detect a residual charge on the output capacitors and not forcefully discharge the capacitors before beginning the softstart sequence, instead, the softstart ramping of the output will begin at the voltage level of the residual charge. For example, if the NCP1589A/B is configured to provide a regulated output voltage of 2.5 V, the normal softstart sequence will ramp the output voltage from 0 to 2.5 V in 4.2 ms; however if the output capcitors already have a 1.2 V charge on them, the NCP1589A/B will not discharge the capacitors, instead the softstart sequence will begin at 1.2 V and then ramp the output to 2.5 V. Power Good The PGOOD pin is an open drain active high output pin that signals the condition of the VOS (Voltage Output Sense) pin. PGOOD is pulled low during soft start cycle, and if there is a latched over current, over voltage, or under voltage fault. If the voltage on the VOS pin is within ±10% of Vref (800 mV) then the PGOOD pin will not be pulled low. The PGOOD pin does not have an internal pull-up resistor. Overvoltage Protection If the voltage on the VOS pin exceeds the over voltage threshold the NCP1589A/B will latch an over voltage fault. During an over voltage fault the UG pin will be pulled low, and the LG pin will be high while the until the voltage on the VOS pin goes below Vref/2 (400 mV). The NCP1589A will continue drive the LG pin, LG will go high if VOS exceeds 1 V and then go low when VOS goes below 400 mV. The power to the NCP1589 must be cycled to reset the over voltage protection fault. Under Voltage Protection If the voltage on the VOS pin falls below the under voltage threshold after the soft start cycle completes, then the NCP1589A/B will latch an under voltage fault. During an under voltage fault, both the UG and LG pins will be pulled low. The power to the NCP1589 must be cycled to reset the under voltage protection fault. Internal Soft-Start To prevent excess inrush current during startup, the NCP1589A/B uses a calibrated current source with an internal soft start capacitor to ramp the reference voltage from 0 to 800 mV over a period of 4 ms. The softstart ramp generator will reset if the input power supply voltages reach http://onsemi.com 6 NCP1589A, NCP1589B 4.0 V 3.6 V VCC Internal UVLO Fault 1.45 V COMP −0.7 V LG 700 mV 50 mV OCP Programmable UG VOUT 0.8 V FB PGOOD POR UVLO SS NORMAL Figure 7. Typical Startup Sequence http://onsemi.com 7 NCP1589A, NCP1589B VOS 1.0V 0.88V 0.8V 0.88V 0.8V 0.72V 0.6V 0.4V PGOOD UG LG Overvoltage Undervoltage Figure 8. Typical Power Good Function Feedback and Compensation Design Example The NCP1589A/B allows the output voltage to be adjusted from 0.8 V to 5.0 V via an external resistor divider network. The controller will try to maintain 0.8 V at feedback pin. Thus, if a resistor divider circuit was placed across the feedback pin to VOUT, the controller will regulate the output voltage proportional to the resistor divider network in order to maintain 0.8 V at the FB pin. The same formula applies to the VOS pin and the controller will maintain 0.8 V at the VOS pin. Voltage Mode Control Loop with TYPE III Compensation Converter Parameters: Input Voltage: VIN = 5 V Output Voltage: VOUT = 1.65 V Switching Frequency: 300 kHz Total Output Capacitance: COUT = 3600 mF Total ESR: ESR = 6 mW Output Inductance: LOUT: 1 mH Ramp Amplitude: VRAMP = 1.1 V VOUT C1 R1 FB R3 C3 R2 C2 R4 VOUT Figure 9. VCOMP Vref ǒVOUTVREF Ǔ * VREF Figure 10. a.. Set a target for the close loop bandwidth at 1/6th of the switching frequency. The same formula can be applied to the feedback resistors at VOS. R9 + R10 − E/A + R4 The relationship between the resistor divider network above and the output voltage is shown in the following equation: R4 + R1 R1 F cross_over :+ 50 kHz ǒVOUTVREF Ǔ * VREF http://onsemi.com 8 NCP1589A, NCP1589B Step 5: Place 2nd zero at the output filter double pole frequency. b.. Output Filter Double Pole Frequency F lc :+ 1 2 @ p @ Ǹ L OUT @ C OUT R3 :+ 2 @ p @ C OUT @ C ESR C3 :+ F ESR + 7.368 kHz Step 7: R4 is sized to maintain the feedback voltage to Vref = 0.8 V. R1 :+ 4.12 kW Step 2: Pick compensation DC gain (R2/R1) for desired close loop bandwidth. Ǔǒ V RAMP V IN @ F cross_over F lc R4 :+ Ǔ The Component values for Type III Compensation are: 2 @ ǸL OUT @ C OUT R2 10 −3 mF Step 4: Place 1st pole at ESR zero frequency. C1 :+ C2 C2 @ R2 @ 2 @ p @ F ESR * 1 C1 + 1.542 V OUT * V REF R1 = 4.12 kW R2 = 17.085 kW R3 = 74.169 W R4 = 3.878 kW C1 = 0.0015 mF C2 = 0.007 mF C3 = 0.014 mF NOTE: Recommend to change values to industry standard component values. Step 3: Place 1st zero at half the output filter double pole frequency. C2 + 7.024 V REF @ R1 R4 + 3.878 kW R2 + 17.085 kW C2 :+ 1 ǒ p @ R3 @ FSWǓ C3 + 0.014 mF Step 1: Set a value for R1 between 2 kW and 5 kW ǒ *1 Step 6: Place 2nd pole at half the switching frequency. 1 V RAMP :+ 1.1 V lc R3 + 74.169 W c.. ESR Zero Frequency: R2 :+ R1 @ SW 2@F F lc + 2.653 kHz F ESR :+ R1 F 10 −3 mF http://onsemi.com 9 NCP1589A, NCP1589B PACKAGE DIMENSIONS DFN10, 3x3, 0.5P CASE 485C−01 ISSUE B D PIN 1 REFERENCE 2X 0.15 C 2X EDGE OF PACKAGE A B ÇÇÇ ÇÇÇ ÇÇÇ ÇÇÇ L1 E DETAIL A Bottom View (Optional) MOLD CMPD 0.15 C 0.10 C (A3) A1 A 10X SIDE VIEW A1 D2 10X L 1 DIM A A1 A3 b D D2 E E2 e K L L1 MILLIMETERS MIN MAX 0.80 1.00 0.00 0.05 0.20 REF 0.18 0.30 3.00 BSC 2.40 2.60 3.00 BSC 1.70 1.90 0.50 BSC 0.19 TYP 0.35 0.45 0.00 0.03 SOLDERING FOOTPRINT* 5 2.6016 E2 K 10 10X 1.8508 2.1746 6 3.3048 b 0.10 C A B 0.05 C C DETAIL A e A3 DETAIL B Side View (Optional) SEATING PLANE 0.08 C 10X ÉÉÉ ÉÉÉ EXPOSED Cu TOP VIEW DETAIL B NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.25 AND 0.30 MM FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. 5. TERMINAL b MAY HAVE MOLD COMPOUND MATERIAL ALONG SIDE EDGE. MOLD FLASHING MAY NOT EXCEED 30 MICRONS ONTO BOTTOM SURFACE OF TERMINAL b. 6. DETAILS A AND B SHOW OPTIONAL VIEWS FOR END OF TERMINAL LEAD AT EDGE OF PACKAGE. BOTTOM VIEW NOTE 3 10X 0.5651 10X 0.5000 PITCH 0.3008 DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 10 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NCP1589A/D