SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Balanced MC Series - Modified TO-220 Balance MC TO-220 Series Description Balanced MC Series Modified TO-220 are low capacitance SIDACtor® devices designed to protect broadband equipment from damaging overvoltage transients. The patented “Y” configuration also ensures balanced overvoltage protection. The series provides a single port solution that enables equipment to comply with various global requlatory standards while limiting the impact to broadband signals. Features and Benefits Agency Approvals Agency t 40% lower capacitance than our Baseband Protectors, for applications that demand greater signal integrity t Low voltage overshoot t Low on-state voltage Agency File Number t Does not degrade with use E133083 t Fails short circuit when surged in excess of ratings Pinout Designation t Robust Modified TO-220 Package t Custom lead forms available t Balanced overvoltage protection PIN 1 Applicable Global Standards PIN 3 PIN 2 Schematic Symbol 1 3 (T) (R) t TIA-968-A t IEC 61000-4-5 t ITU K.20/21 Enhanced Level t YD/T 1082 t ITU K.20/21 Basic t YD/T 950 t YD/T 993 t GR 1089 Inter-building t GR 1089 Intra-building 2 (G) Electrical Characteristics Part Number Marking VDRM @lDRM=5μA VS @100V/μs IH IS IT VT @IT=2.2 Amps V min V max mA max Pins 1-2, 3-2, 1-3 mA max A max V min 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 8 8 8 8 8 8 8 8 Pins 1-2, 3-2, 1-3 P1553ACMCLxx P1803ACMCLxx P2103ACMCLxx P2353ACMCLxx P2703ACMCLxx P3203ACMCLxx P3403ACMCLxx P5103ACMCLxx P1553ACMC P1803ACMC P2103ACMC P2353ACMC P2703ACMC P3203ACMC P3403ACMC P5103ACMC 130 150 170 200 230 270 300 420 180 210 250 270 300 350 400 600 Capacitance See Capacitance Values Table Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). - XX Part Number Suffix: ‘RP’ (Reel Pack), Blank (Bulk Pack), or ‘60’ (Type 60 lead form, Bulk Pack. Special order item -- contact factory.) 85 © 2010 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Capacitance Values P1553ACMCLxx P1803ACMCLxx P2103ACMCLxx P2353ACMCLxx P2703ACMCLxx P3203ACMCLxx P3403ACMCLxx P5103ACMCLxx pF Pin 1-2 / 3-2 Tip-Ground, Ring-Ground MIN MAX 30 55 30 60 30 45 25 45 25 40 25 40 20 35 20 30 pF Pin 1-3 Tip-Ring MIN MAX 20 35 15 30 15 30 15 30 15 30 15 30 15 25 10 20 Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. Surge Ratings IPP Series C 1 1 1 1 ITSM 50/60 Hz di/dt A min A min A/μs max 200 30 500 0.2x310 0.5x700 2 2x10 2x10 2 8x20 1.2x50 2 10x160 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 A min A min A min A min A min A min A min A min 50 500 400 200 150 200 175 100 Notes: 1 Current waveform in μs 2 Voltage waveform in μs - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The device must initially be in thermal equilibrium with -40°C < TJ < +150°C Thermal Considerations Package Symbol Modified TO-220 PIN 1 Value Unit TJ Operating Junction Temperature Range -40 to +150 °C TS Storage Temperature Range -65 to +150 °C 50 °C/W R0JA PIN 3 PIN 2 Parameter Thermal Resistance: Junction to Ambient V-I Characteristics tr x td Pulse Waveform +I IPP – Peak Pulse Current – %IPP Balance MC TO-220 Series Part Number IT IS IH IDRM -V +V VT VDRM VS Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t – Time (μs) -I 86 © 2010 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Normalized DC Holding Current vs. Case Temperature 2.0 10 IH 8 6 25 °C 4 2 1.8 IH (TC = 25ºC) 14 12 1.6 1.4 0 -4 25°C 1.2 Ratio of Percent of VS Change – % 1.0 0.8 0.6 -6 -8 0.4 -40 -20 0 -40 20 40 60 80 100 120 140 160 -20 Junction Temperature (TJ) – °C 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC Soldering Parameters Reflow Condition - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Figure 1 TP tP Critical Zone TL to TP Ramp-up Temperature Balance MC TO-220 Series Normalized VS Change vs. Junction Temperature TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Physical Specifications Environmental Specifications Lead Material Copper Alloy High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Terminal Finish 100% Matte-Tin Plated Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C Peak). JEDEC-J-STD-020, Level 1 Body Material UL recognized epoxy meeting flammability classification 94V-0 87 © 2010 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Part Numbering Part Marking P xxx 3 A C MC L xx TYPE P = SIDACtor xxxxx Blank, RP or 60 -for Type 60 orders, contact factory MEDIAN VOLTAGE MC Series IPP RATING Dimensions - Modified TO-220 Tape and Reel Specification — Modified TO-220 Inches O Min D Temperature Measurement Point F G P PIN 3 PIN 2 PIN 1 L M K H Date Code RoHS COMPLIANT PACKAGE TYPE A Part Marking Code (Refer to Electrical Characteristics Table) PACKING OPTIONS CONSTRUCTION VARIABLE Balance MC TO-220 Series XXXXXXXXX N J The modified TO-220 package is designed to meet mechanical standards as set forth in JEDEC publication number 95. Millimeters Max Min 0.240 (6.10) Max A 0.400 0.410 10.16 10.42 D 0.360 0.375 9.14 9.53 F 0.110 0.130 2.80 3.30 G 0.540 0.575 13.71 14.61 H 0.025 0.035 0.63 0.89 J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 L 0.060 0.075 1.52 1.90 M 0.070 0.085 1.78 2.16 N O P 0.018 0.024 0.46 0.61 0.178 0.290 0.188 0.310 4.52 7.37 4.78 7.87 0.019 (0.5) 1.626 (41.15) 0.720 (18.29) 0.750 ± 0.010 (19.05 ± 0.25) 0.360 (9.14) 0.500 (12.7) 0.100 (2.54) 0.100 (2.54) 14.173 (360.0) Dimensions are in inches (and millimeters). Direction of Feed 1.968 (50.0) Packing Options Package Type A Description Quantity Added Suffix Industry Standard Modified TO-220 Tape and Reel Pack 700 RP EIA-468-B Modified TO-220 Bulk Pack 500 N/A N/A Modified TO-220, Type 60 Lead Form Bulk Pack 500 60 (special order item, contact factory for details) N/A 88 © 2010 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information.