AC-DC 200 Watts xppower.com PBM200 Series • Worldwide Medical Approvals • Single, Dual, Triple and Quad Outputs • Small Size - Only 7” x 4” x 1.5” • Power Fail Detect & Remote On/Off • Universal AC Input with Active PFC • High Reliability - 350k Hours MTBF • 100 Watt Convection-Cooled Rating Specification Input General Input Voltage Input Frequency Input Current • 90-264 VAC • 47-63 Hz • 3.2 A rms at 115 VAC, 1.6 A rms at 230 VAC Inrush Current • 20 A at 115 VAC, 40 A at 230 VAC cold start 25 ºC Power Factor • 0.98 typical Earth Leakage Current • 90 µA max at 115 VAC, 60 Hz 150 µA max at 230 VAC, 50 Hz Input Protection • Both line and neutral fused Output Output Voltage Output Voltage Trim Initial Set Accuracy Minimum Load Start Up Delay Start Up Rise Time Hold Up Time Drift Line Regulation Load Regulation Transient Response • • • • • • • • • • • Ripple & Noise • Overvoltage Protection • Overtemperature Protection • Overload Protection Short Circuit Protection Temperature Coefficient Remote Sense • • • Remote On/Off See table Not user-adjustable ±2% See table & note 5 2 s max 18 ms typical 20 ms minimum at full load & 110 VAC ±0.2% ±0.5% max See note 7 4% max deviation, recovery to within 1% in 500 µs for a 25% load change 2% max pk-pk, 20 MHz BW with a 22 µF electrolytic & a 0.47 µF tantalum capacitor 112-140% Vnom output 1 only, recycle input to reset Shutdown at +85 ºC (singles) or +105 ºC (multi outputs) with auto recovery, measured internally 140-200% typical, auto recovery Trip and restart (Hiccup mode) 0.04%/˚C • Single output models only. Compensates for up to 0.5 V drop • On = Logic low or open circuit Off = Logic high Efficiency Isolation Switching Frequency Power Density Power Fail Detect MTBF • Up to 80% • 4000 VAC Input to Output 1500 VAC Input to Ground 500 VAC Output to Ground • 100 kHz ±12 kHz • 4.76 W/In3 • AC OK = TTL logic high AC not OK = TTL logic low • 350 kHrs per MIL-HDBK-217F at +25 ˚C Environmental Operating Temperature • 0 ˚C to +70 ˚C, derate linearly from 100% power at +50 ˚C to 50% power at +70 ˚C Cooling • ‘C’ versions have internal fan, ‘B’ versions are derated with convection cooling or require 25 CFM (see note 4) Operating Humidity • Up to 95% RH, non-condensing Storage Temperature • -40 ˚C to +85 ˚C Operating Altitude • 2500 m Shock • Half sine pulse. acceleration 50 g, 11 ms duration, 3 shocks in each direction, unpackaged, non-operating Vibration • Sinusoidal 10-55 Hz, amplitude 0.15 mm, 30 min/axis, unpackaged, non-operating EMC & Safety Emissions Harmonic Currents Voltage Flicker ESD Immunity Radiated Immunity EFT/Burst Surge Conducted Immunity Dips & Interruptions Safety Approvals • EN55011 & FCC Class B conducted & radiated • EN61000-3-2 • EN61000-3-3 • EN61000-4-2, level 3 Perf Criteria A • EN61000-4-3, level 3 Perf Criteria A • EN61000-4-4, level 3 Perf Criteria A • EN61000-4-5, level 3 Perf Criteria A • EN61000-4-6 3 V, Perf Criteria A • EN61000-4-11, 30% 10 ms, 60% 100 ms, >95% 5000 ms, Perf Criteria A, B, B • EN60601-1, UL60601-1, CSA22.2 No. 601-1 per cUL, CE Mark Output 1(8) Output Power(4) Vnom (5) Output 2(2,5) (7) Imin Imax Reg Vnom Output 3(5) (7) Imax Reg Vnom Output 4(3,5) (7) Imax Reg Vnom Imax Model Number(1) Reg(7) 150 W 3.3 V 3.0 A 46.0 A 3% PBM200PS3V3-C† 175 W 5.1 V 3.0 A 35.0 A 2% PBM200PS05-C† 200 W 12.0 V 1.2 A 16.7 A 2% PBM200PS12-C† 200 W 15.0 V 1.0 A 13.4 A 2% PBM200PS15-C† 200 W 24.0 V 0.6 A 8.4 A 2% PBM200PS24-C† 200 W 30.0 V 0.5 A 6.7 A 2% PBM200PS30-C 200 W 48.0 V 0.5 A 4.2 A 2% 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 8.0 A 4% PBM200PD01-C 200 W +5.1 V 3.0 A 30.0 A 2% +15 V 6.0 A 4% PBM200PD02-C 200 W +5.1 V 3.0 A 30.0 A 2% +24 V 4.0 A 4% PBM200PD03-C 200 W +12.0 V 1.0 A 8.7 A 2% +24 V 4.0 A 4% PBM200PD04-C 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 8.0 A 4% -5 V 6.0 A 4% PBM200PT01-C 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 8.0 A 4% -12 V 4.0 A 4% PBM200PT02-C† 200 W +5.1 V 3.0 A 30.0 A 2% +15 V 6.0 A 4% -15 V 4.0 A 4% 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 8.0 A 4% 200 W +5.1 V 3.0 A 30.0 A 2% +15 V 6.0 A 4% -12 V 4.0 A 4% 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 8.0 A 4% -12 V 4.0 A 200 W +5.1 V 3.0 A 30.0 A 2% +15 V 6.0 A 4% -15 V 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 8.0 A 4% 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 8.0 A 200 W +5.1 V 3.0 A 30.0 A 2% +12 V 175 W +3.3 V 3.0 A 30.0 A 3% +5.1 V PBM200PS48-C† 4% PBM200PT03-C† F 24 V 4.0 A 4% PBM200PT04-C 4% F5V 6.0 A 4% PBM200PQ01-C 4.0 A 4% F 24 V 4.0 A 4% PBM200PQ02-C† -12 V 4.0 A 4% F 12 V 4.0 A 4% PBM200PQ03-C 4% -15 V 4.0 A 4% F 15 V 4.0 A 4% PBM200PQ04-C 8.0 A 4% -12 V 4.0 A 4% F 24 V 4.0 A 4% PBM200PQ05-C† 8.0 A 4% -12 V 4.0 A 4% F 12 V 4.0 A 4% PBM200PQ06-C† PBM200PT05-C Notes 1. For U-bracket format, replace suffix ‘-C’ with suffix ‘-B’. 2. Output 2 peak current is 12 A on +12 V, 9 A on +15 V, and 6 A on +24 V. Maximum 2 s duration with total load <200 W. 3. Output 4 is floating and can be connected externally for positive or negative output. 4. 200 W for ‘-C’ version with a cover and fan assembly. 100 W for ‘-B’ version with convection cooling (maximum current of output 1 & 2 derated to 50%). 200 W for ‘-B’ version with 25 CFM forced air provided by user. 5. Zero minimum load for outputs 2, 3 & 4. All models may be operated at noload on output 1, but voltage total regulation increases to 10%. 6. When the Remote Sense facility is not used, +Sense must be connected to +V, and –Sense to return, on P2 connector. 7. Total regulation includes initial tolerance, line regulation and load regulation. 8. Peak current for single output models is 140% of Imax. Maximum 2 s duration with 10% duty cycle. 9. † Available from Farnell. See pages 204-206. Mechanical Details Model Number(s) B: Mounting holes. Threaded inserts for 6.32" screws (8 places) A: Mounting holes. Threaded inserts for M3 0.5 screws (8 places) Conn B B A A 1.00 (25.4) P2 0.50 (12.7) 6.00 (152.4) A A B B 1 P2 P4 1 3.00 (76.2) 2.30 (58.4) P3 P3 1 4.00 (101.6) P5 P1 B G 1.00 (25.4) A A A A B B 0.85 (21.6) 1.50 (38.1) 0.65 (16.5) PDXX PTXX (except 04) -SENSE OP1 OP1 Return OP1 OP1 Return Com Ret Com Ret Return Com Ret Com Ret Return Com Ret Com Ret OP1 OP2 OP2 OP1 N.C. OP3 OP1 N.C. N.C. +SENSE N.C. N.C. Fan Com Ret Com Ret PFD PFD PFD PT04 PQXX OP1 OP1 Com Ret Com Ret Com Ret OP2 N.C. OP4 Ret OP4 OP1 OP1 Com Ret Com Ret Com Ret OP2 OP3 OP4 Ret OP4 PFD PFD Notes B 9 0.50 (12.7) PSXX 1 L N Pin 1 2 3 4 5 6 7 8 9 1 2 3 4 7.00 (177.8) 1. Dimensions shown in inches (mm). 2. Tolerance 0.02 [0.5] maximum. 3. Input connector P1 is Dinkle DT-35-B01W-03, output connector P2 is Dinkle DT-35-B01W-09 screws are M3, Nickel plated. 4. Connector P3 mates with Molex housing 22-01-1043 & Molex 40445 series crimp terminal. 5. Connectors P4 & P5 mate with Molex housing 22-01-1023 & Molex 40445 series crimp terminal. 6. P4 is for DC fan rated at 24 V/0.2 A (models PBM200PD03 & PD04), 5 V/0.38 A (PBM200PQ06), or 12 V/0.2 A (all other models). Pin 1 Fan+, pin 2 Fan-. 7. P5 is for Remote On/Off. Pin 1 is positive, pin 2 is return. 8. Weight:1.83 lb (0.82kg) approx. for ‘-B’ version, 2.14 lb (0.96kg) approx. for ‘-C’ version. 17-Apr-07 AC-DC PBM200 Models and Ratings