PCA9534A REMOTE 8-BIT AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS I2C www.ti.com SCPS141B – SEPTEMBER 2006 – REVISED MARCH 2007 FEATURES 3 14 4 13 5 12 6 11 7 10 8 9 VCC SDA SCL INT P7 P6 P5 P4 A1 A0 A2 1 16 15 14 13 12 P0 2 11 INT P1 3 10 P7 P2 4 9 P6 5 6 7 8 P5 15 P4 16 2 GND 1 P3 A0 A1 A2 P0 P1 P2 P3 GND RGT PACKAGE (TOP VIEW) SCL A2 P0 P1 P2 VCC S DA RGV PACKAGE (TOP VIEW) A1 DB, DBQ, DGV, DW, OR PW PACKAGE (TOP VIEW) • 16 15 14 13 12 SCL 11 INT 2 3 10 P7 1 9 P6 4 5 6 7 8 P3 GND P4 P5 • • • • Power-Up With All Channels Configured as Inputs No Glitch on Power-Up Noise Filter on SCL/SDA Inputs Latched Outputs With High-Current Drive Maximum Capability for Directly Driving LEDs Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II ESD Protection Exceeds JESD 22 – 2000-V Human-Body Model (A114-A) – 200-V Machine Model (A115-A) – 1000-V Charged-Device Model (C101) SDA • • • • • • VCC • • • • Low Standby Current Consumption of 1 µA Max I2C to Parallel Port Expander Open-Drain Active-Low Interrupt Output Operating Power-Supply Voltage Range of 2.3 V to 5.5 V 5-V Tolerant I/O Ports 400-kHz Fast I2C Bus Three Hardware Address Pins Allow up to Eight Devices on the I2C/SMBus Input/Output Configuration Register Polarity Inversion Register Internal Power-On Reset A0 • DESCRIPTION/ORDERING INFORMATION This 8-bit I/O expander for the two-line bidirectional bus (I2C) is designed for 2.3-V to 5.5-V VCC operation. It provides general-purpose remote I/O expansion for most microcontroller families via the I2C interface [serial clock (SCL), serial data (SDA)]. The PCA9534A consists of one 8-bit configuration (input or output selection), input port, output port, and polarity inversion (active high or active low) register. At power on, the I/Os are configured as inputs. However, the system master can enable the I/Os as either inputs or outputs by writing to the I/O configuration bits. The data for each input or output is kept in the corresponding input or output register. The polarity of the input port register can be inverted with the polarity inversion register. All registers can be read by the system master. The system master can reset the PCA9534A in the event of a timeout or other improper operation by utilizing the power-on reset feature, which puts the registers in their default state and initializes the I2C/SMBus state machine. The PCA9534A open-drain interrupt (INT) output is activated when any input state differs from its corresponding input port register state and is used to indicate to the system master that an input state has changed. INT can be connected to the interrupt input of a microcontroller. By sending an interrupt signal on this line, the remote I/O can inform the microcontroller if there is incoming data on its ports without having to communicate via the I2C bus. Thus, the PCA9534A can remain a simple slave device. The device's outputs (latched) have high-current drive capability for directly driving LEDs. It has low current consumption. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2006–2007, Texas Instruments Incorporated PCA9534A REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS www.ti.com SCPS141B – SEPTEMBER 2006 – REVISED MARCH 2007 Three hardware pins (A0, A1, and A2) are used to program and vary the fixed I2C address and allow up to eight devices to share the same I2C bus or SMBus. The PCA9534A is pin-to-pin and I2C address compatible with the PCF8574A. However, software changes are required due to the enhancements in the PCA9534A over the PCF8574A. The PCA9534A is a low-power version of the PCA9554A. The only difference between the PCA9534A and PCA9554A is that the PCA9534A eliminates an internal I/O pullup resistor, which dramatically reduces power consumption in the standby mode when the I/Os are held low. The PCA9534A and PCA9534 are identical, except for their fixed I2C address. This allows for up to 16 of these devices (8 of each) on the same I2C bus. ORDERING INFORMATION PACKAGE (1) TA Reel of 3000 PCA9534ARGTR PREVIEW QFN – RGV Reel of 2500 PCA9534ARGVR PREVIEW QSOP – DBQ Reel of 2500 PCA9534ADBQR PDA534A Tube of 40 PCA9534ADW Reel of 2000 PCA9534ADWR Reel of 2000 PCA9534ADBR Tube of 80 PCA9534ADB Tube of 90 PCA9534APW Reel of 2000 PCA9534APWR Reel of 2000 PCA9534ADGVR –40°C to 85°C SSOP – DB TSSOP – PW TVSOP – DGV 2 TOP-SIDE MARKING QFN – RGT SOIC – DW (1) ORDERABLE PART NUMBER PCA9534A PDA534A PD534A PD534A Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Submit Documentation Feedback PCA9534A REMOTE 8-BIT AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS I2C www.ti.com SCPS141B – SEPTEMBER 2006 – REVISED MARCH 2007 TERMINAL FUNCTIONS NO. QSOP (DBQ), SOIC (DW), SSOP (DB), TSSOP (PW), AND TVSOP (DGV) QFN (RGT) AND QFN (RGV) NAME 1 15 A0 Address input. Connect directly to VCC or ground. 2 16 A1 Address input. Connect directly to VCC or ground. 3 1 A2 Address input. Connect directly to VCC or ground. 4 2 P0 P-port input/output. Push-pull design structure. 5 3 P1 P-port input/output. Push-pull design structure. 6 4 P2 P-port input/output. Push-pull design structure. 7 5 P3 P-port input/output. Push-pull design structure. 8 6 GND 9 7 P4 P-port input/output. Push-pull design structure. 10 8 P5 P-port input/output. Push-pull design structure. 11 9 P6 P-port input/output. Push-pull design structure. 12 10 P7 P-port input/output. Push-pull design structure. 13 11 INT Interrupt output. Connect to VCC through a pullup resistor. 14 12 SCL Serial clock bus. Connect to VCC through a pullup resistor. 15 13 SDA Serial data bus. Connect to VCC through a pullup resistor. 16 14 VCC Supply voltage DESCRIPTION Ground LOGIC DIAGRAM (POSITIVE LOGIC) INT A0 A1 A2 SCL SDA 13 Interrupt Logic LP Filter 1 2 P7−P0 3 14 15 Input Filter I2C Bus Control Shift Register 8 Bits I/O Port Write Pulse VCC GND 16 8 Power-On Reset Read Pulse A. Pin numbers shown are for DB, DBQ, DGV, DW, or PW package. B. All I/Os are set to inputs at reset. Submit Documentation Feedback 3 PCA9534A REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS www.ti.com SCPS141B – SEPTEMBER 2006 – REVISED MARCH 2007 SIMPLIFIED SCHEMATIC OF P0 TO P7 Data From Shift Register Data From Shift Register Output Port Register Data Configuration Register D VCC Q1 Q FF Write Configuration Pulse Write Pulse CK Q D Q FF P0 to P7 CK Q Q2 Output Port Register Input Port Register D Q FF Read Pulse CK Q Data From Shift Register D Q ESD Protection Diode GND Input Port Register Data To INT Polarity Register Data FF Write Polarity Pulse CK Q Polarity Inversion Register A. At power-on reset, all registers return to default values. I/O Port When an I/O is configured as an input, FETs Q1 and Q2 are off, creating a high-impedance input. The input voltage may be raised above VCC to a maximum of 5.5 V. If the I/O is configured as an output, Q1 or Q2 is enabled, depending on the state of the output port register. In this case, there are low-impedance paths between the I/O pin and either VCC or GND. The external voltage applied to this I/O pin should not exceed the recommended levels for proper operation. I2C Interface The bidirectional I2C bus consists of the serial clock (SCL) and serial data (SDA) lines. Both lines must be connected to a positive supply through a pull-up resistor when connected to the output stages of a device. Data transfer may be initiated only when the bus is not busy. I2C communication with this device is initiated by a master sending a start condition, a high-to-low transition on the SDA input/output while the SCL input is high (see Figure 1). After the start condition, the device address byte is sent, MSB first, including the data direction bit (R/W). After receiving the valid address byte, this device responds with an acknowledge (ACK), a low on the SDA input/output during the high of the ACK-related clock pulse. The address inputs (A0–A2) of the slave device must not be changed between the start and the stop conditions. On the I2C bus, only one data bit is transferred during each clock pulse. The data on the SDA line must remain stable during the high pulse of the clock period, as changes in the data line at this time are interpreted as control commands (start or stop) (see Figure 2). A stop condition, a low-to-high transition on the SDA input/output while the SCL input is high, is sent by the master (see Figure 1). 4 Submit Documentation Feedback PCA9534A REMOTE 8-BIT AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS I2C www.ti.com SCPS141B – SEPTEMBER 2006 – REVISED MARCH 2007 Any number of data bytes can be transferred from the transmitter to receiver between the start and the stop conditions. Each byte of eight bits is followed by one ACK bit. The transmitter must release the SDA line before the receiver can send an ACK bit. The device that acknowledges must pull down the SDA line during the ACK clock pulse so that the SDA line is stable low during the high pulse of the ACK-related clock period (see Figure 3). When a slave receiver is addressed, it must generate an ACK after each byte is received. Similarly, the master must generate an ACK after each byte that it receives from the slave transmitter. Setup and hold times must be met to ensure proper operation. A master receiver will signal an end of data to the slave transmitter by not generating an acknowledge (NACK) after the last byte has been clocked out of the slave. This is done by the master receiver by holding the SDA line high. In this event, the transmitter must release the data line to enable the master to generate a stop condition. SDA SCL S P Start Condition Stop Condition Figure 1. Definition of Start and Stop Conditions SDA SCL Data Line Stable; Data Valid Change of Data Allowed Figure 2. Bit Transfer Data Output by Transmitter NACK Data Output by Receiver ACK SCL From Master 1 2 8 9 S Clock Pulse for Acknowledgment Start Condition Figure 3. Acknowledgment on I2C Bus Submit Documentation Feedback 5 PCA9534A REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS www.ti.com SCPS141B – SEPTEMBER 2006 – REVISED MARCH 2007 Interface Definition BYTE I2C slave address Px I/O data bus BIT 7 (MSB) 6 5 4 3 2 1 0 (LSB) L H H H A2 A1 A0 R/W P7 P6 P5 P4 P3 P2 P1 P0 Device Address Figure 4 shows the address byte of the PCA9534A. Slave Address 0 1 1 1 A2 A1 A0 R/W Hardware Selectable Fixed Figure 4. PCA9534A Address Address Reference INPUTS I2C BUS SLAVE ADDRESS A2 A1 A0 L L L 56 (decimal), 38 (hexadecimal) L L H 57 (decimal), 39 (hexadecimal) L H L 58 (decimal), 3A (hexadecimal) L H H 59 (decimal), 3B (hexadecimal) H L L 60 (decimal), 3C (hexadecimal) H L H 61 (decimal), 3D (hexadecimal) H H L 62 (decimal), 3E (hexadecimal) H H H 63 (decimal), 3F (hexadecimal) The last bit of the slave address defines the operation (read or write) to be performed. When it is high (1), a read is selected, while a low (0) selects a write operation. Control Register and Command Byte Following the successful acknowledgment of the address byte, the bus master sends a command byte which is stored in the control register in the PCA9534A. Two bits of this command byte state the operation (read or write) and the internal register (input, output, polarity inversion or configuration) that will be affected. This register can be written or read through the I2C bus. The command byte is sent only during a write transmission. Once a command byte has been sent, the register that was addressed continues to be accessed by reads until a new command byte has been sent. 0 0 0 0 0 0 B1 B0 Figure 5. Control Register Bits 6 Submit Documentation Feedback PCA9534A REMOTE 8-BIT AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS I2C www.ti.com SCPS141B – SEPTEMBER 2006 – REVISED MARCH 2007 Command Byte CONTROL REGISTER BITS COMMAND BYTE (HEX) REGISTER PROTOCOL POWER-UP DEFAULT Input Port Read byte xxxx xxxx B1 B0 0 0 0x00 0 1 0x01 Output Port Read/write byte 1111 1111 1 0 0x02 Polarity Inversion Read/write byte 0000 0000 1 1 0x03 Configuration Read/write byte 1111 1111 Register Descriptions The input port register (register 0) reflects the incoming logic levels of the pins, regardless of whether the pin is defined as an input or an output by the configuration register. It only acts on read operation. Writes to these registers have no effect. The default value, X, is determined by the externally applied logic level. Before a read operation, a write transmission is sent with the command byte to let the I2C device know that the input port register will be accessed next. Register 0 (Input Port Register) BIT I7 I6 I5 I4 I3 I2 I1 I0 DEFAULT X X X X X X X X The output port register (register 1) shows the outgoing logic levels of the pins defined as outputs by the configuration register. Bit values in this register have no effect on pins defined as inputs. In turn, reads from this register reflect the value that is in the flip-flop controlling the output selection, not the actual pin value. Register 1 (Output Port Register) BIT O7 O6 O5 O4 O3 O2 O1 O0 DEFAULT 1 1 1 1 1 1 1 1 The polarity inversion register (register 2) allows polarity inversion of pins defined as inputs by the configuration register. If a bit in this register is set (written with 1), the corresponding port pin polarity is inverted. If a bit in this register is cleared (written with a 0), the corresponding port pin original polarity is retained. Register 2 (Polarity Inversion Register) BIT N7 N6 N5 N4 N3 N2 N1 N0 DEFAULT 0 0 0 0 0 0 0 0 The configuration register (register 3) configures the directions of the I/O pins. If a bit in this register is set to 1, the corresponding port pin is enabled as an input with high-impedance output driver. If a bit in this register is cleared to 0, the corresponding port pin is enabled as an output. Register 3 (Configuration Register) BIT C7 C6 C5 C4 C3 C2 C1 C0 DEFAULT 1 1 1 1 1 1 1 1 Power-On Reset When power (from 0 V) is applied to VCC, an internal power-on reset holds the PCA9534A in a reset condition until VCC has reached VPOR. At that point, the reset condition is released and the PCA9534A registers and I2C/SMBus state machine initialize to their default states. After that, VCC must be lowered to below 0.2 V and then back up to the operating voltage for a power-reset cycle. Submit Documentation Feedback 7 PCA9534A REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS www.ti.com SCPS141B – SEPTEMBER 2006 – REVISED MARCH 2007 Interrupt Output (INT) An interrupt is generated by any rising or falling edge of the port inputs in the input mode. After time, tiv, the signal INT is valid. Resetting the interrupt circuit is achieved when data on the port is changed to the original setting, data is read from the port that generated the interrupt or in a stop event. Resetting occurs in the read mode at the acknowledge (ACK) or not acknowledge (NACK) bit after the rising edge of the SCL signal. In a stop event, INT is cleared after the rising edge of SDA. Interrupts that occur during the ACK or NACK clock pulse can be lost (or be very short) due to the resetting of the interrupt during this pulse. Each change of the I/Os after resetting is detected and is transmitted as INT. Reading from or writing to another device does not affect the interrupt circuit, and a pin configured as an output cannot cause an interrupt. Changing an I/O from an output to an input may cause a false interrupt to occur if the state of the pin does not match the contents of the Input Port register. The INT output has an open-drain structure and requires pull-up resistor to VCC. Bus Transactions Data is exchanged between the master and PCA9534A through write and read commands. Writes Data is transmitted to the PCA9534A by sending the device address and setting the least-significant bit to a logic 0 (see Figure 4 for device address). The command byte is sent after the address and determines which register receives the data that follows the command byte (see Figure 6 and Figure 7). There is no limitation on the number of data bytes sent in one write transmission. SCL 1 2 3 4 5 6 7 8 9 Slave Address S SDA 0 1 1 Command Byte 1 A2 A1 A0 0 A 0 0 0 0 0 0 0 1 A Data 1 A P ACK From Slave ACK From Slave R/W ACK From Slave Start Condition Data to Port Write to Port Data Out From Port Data 1 Valid tpv Figure 6. Write to Output Port Register <br/> SCL 1 2 3 4 5 6 7 8 9 Slave Address SDA S 0 1 1 Command Byte 1 A2 A1 A0 0 Start Condition R/W A 0 0 0 0 ACK From Slave 0 0 Data to Register 1 1/0 A Data ACK From Slave Data to Register Figure 7. Write to Configuration or Polarity Inversion Registers 8 Submit Documentation Feedback A P ACK From Slave PCA9534A REMOTE 8-BIT AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS I2C www.ti.com SCPS141B – SEPTEMBER 2006 – REVISED MARCH 2007 Reads The bus master first must send the PCA9534A address with the least-significant bit set to a logic 0 (see Figure 4 for device address). The command byte is sent after the address and determines which register is accessed. After a restart, the device address is sent again but, this time, the least-significant bit is set to a logic 1. Data from the register defined by the command byte then is sent by the PCA9534A (see Figure 8 and Figure 9). After a restart, the value of the register defined by the command byte matches the register being accessed when the restart occurred. Data is clocked into the register on the rising edge of the ACK clock pulse. There is no limitation on the number of data bytes received in one read transmission, but when the final byte is received, the bus master must not acknowledge the data. S 0 1 1 ACK From Slave ACK From Slave Slave Address 1 A2 A1 A0 0 Command Byte A A S 0 ACK From ACK From Master Slave Data from Register Slave Address 1 1 Data A Data from Register NACK From Master 1 A2 A1 A0 1 A R/W R/W Data NA P Last Byte Figure 8. Read From Register <br/> 1 SCL 2 3 4 5 6 7 8 9 Data From Port Slave Address S 0 SDA 1 Start Condition 1 1 A2 A1 A0 0 R/W Data 1 A Data From Port Data 4 A ACK From Slave ACK From Master NA P NACK From Master Stop Condition Read From Port Data Into Port Data 2 tph Data 3 Data 4 Data 5 tps INT tiv tir A. This figure assumes that the command byte has previously been programmed with 00h. B. Transfer of data can be stopped at any moment by a stop condition. C. This figure eliminates the command byte transfer, a restart and slave address call between the initial slave address call and the actual data transfer from the P Port. See Figure 8 for these details. Figure 9. Read Input Port Register Submit Documentation Feedback 9 PCA9534A REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS www.ti.com SCPS141B – SEPTEMBER 2006 – REVISED MARCH 2007 Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN MAX VCC Supply voltage range –0.5 6 V VI Input voltage range (2) –0.5 6 V range (2) VO Output voltage IIK Input clamp current VI < 0 –20 mA IOK Output clamp current VO < 0 –20 mA IIOK Input/output clamp current VO < 0 or VO > VCC ±20 mA IOL Continuous output low current VO = 0 to VCC 50 mA IOH Continuous output high current VO = 0 to VCC –50 mA ICC θJA –0.5 Continuous current through GND –250 Continuous current through VCC 160 Package thermal impedance (3) DB package 82 DBQ package 90 DGV package 86 DW package 46 N package 67 PW package Tstg (1) (2) (3) 6 UNIT mA °C/W 88 RGT package TBD RGV package TBD Storage temperature range V –65 150 °C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed. The package thermal impedance is calculated in accordance with JESD 51-7. Recommended Operating Conditions VCC Supply voltage MIN MAX 2.3 5.5 0.7 × VCC 5.5 2 5.5 SCL, SDA –0.5 0.3 × VCC A2–A0, P7–P0 –0.5 0.8 SCL, SDA UNIT V VIH High-level input voltage VIL Low-level input voltage IOH High-level output current P7–P0 –10 mA IOL Low-level output current P7–P0 25 mA TA Operating free-air temperature 85 °C 10 A2–A0, P7–P0 –40 Submit Documentation Feedback V V PCA9534A REMOTE 8-BIT AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS I2C www.ti.com SCPS141B – SEPTEMBER 2006 – REVISED MARCH 2007 Electrical Characteristics over operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS VIK Input diode clamp voltage II = –18 mA VPOR Power-on reset voltage VI = VCC or GND, IO = 0 IOH = –8 mA P-port high-level output voltage (2) VOH IOH = –10 mA SDA VOL = 0.4 V VOL = 0.5 V P port (3) IOL VOL = 0.7 V INT SCL, SDA II A2–A0 VCC MIN 2.3 V to 5.5 V –1.2 VPOR 2.3 V 1.8 3V 2.6 4.5 V 4.1 4.75 V 4.1 2.3 V 1.7 3V 2.5 TYP (1) MAX 1.5 1.65 UNIT V V V 4.5 V 4 4.75 V 4 2.3 V to 5.5 V 3 8 2.3 V 8 10 3V 8 14 4.5 V 8 17 4.75 V 8 35 2.3 V 10 13 3V 10 19 4.5 V 10 24 4.75 V 10 45 VOL = 0.4 V 2.3 V to 5.5 V 3 10 VI = VCC or GND 2.3 V to 5.5 V mA ±1 ±1 µA IIH P port VI = VCC 2.3 V to 5.5 V 1 µA IIL P port VI = GND 2.3 V to 5.5 V –1 µA VI = VCC or GND, IO = 0, I/O = inputs, fscl = 400 kHz Operating mode VI = VCC or GND, IO = 0, I/O = inputs, fscl = 100 kHz ICC Standby mode ∆ICC CI Cio (1) (2) (3) Additional current in standby mode SCL SDA P port VI = GND, IO = 0, I/O = inputs, fscl = 0 kHz One input at VCC – 0.6 V, Other inputs at VCC or GND All LED I/Os at VI = 4.3 V, fscl = 0 kHz VI = VCC or GND VIO = VCC or GND 5.5 V 104 175 3.6 V 50 90 2.7 V 20 65 5.5 V 60 150 3.6 V 15 40 2.7 V 8 20 5.5 V 0.25 1 3.6 V 0.2 0.9 2.7 V 0.1 0.8 2.3 V to 5.5 V µA 1.5 mA 5.5 V 2.3 V to 5.5 V 2.3 V to 5.5 V 1 4 5 5.5 6.5 8 9.5 pF pF All typical values are at nominal supply voltage (2.5-V, 3.3-V, or 5-V VCC) and TA = 25°C. The total current sourced by all I/Os must be limited to 85 mA. Each I/O must be externally limited to a maximum of 25 mA, and the P port (P7–P0) must be limited to a maximum current of 200 mA. Submit Documentation Feedback 11 PCA9534A REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS www.ti.com SCPS141B – SEPTEMBER 2006 – REVISED MARCH 2007 I2C Interface Timing Requirements over operating free-air temperature range (unless otherwise noted) (see Figure 10) STANDARD MODE I2C BUS MIN MAX 100 FAST MODE I2C BUS UNIT MIN MAX 0 400 fscl I2C clock frequency 0 tsch I2C clock high time 4 0.6 µs tscl I2C clock low time 4.7 1.3 µs tsp I2C tsds I2C serial-data setup time tsdh I2C serial-data hold time ticr I2C input rise time ticf I2C tocf I2C output fall time tbuf I2C bus free time between stop and start 4.7 1.3 µs tsts I2C start or repeated start condition setup 4.7 0.6 µs tsth I2C start or repeated start condition hold 4 0.6 µs tsps I2C stop condition setup 4 0.6 µs 50 ns spike time 50 100 0 0 300 tvd(ack) Valid data time of ACK condition ACK signal from SCL low to SDA (out) low 0.3 Cb I2C bus capacitive load ns ns 20 + 0.1Cb (1) 300 ns 300 20 + 0.1Cb (1) 300 ns 300 20 + 0.1Cb (1) 300 10-pF to 400-pF bus SCL low to SDA output valid ns 1000 input fall time tvd(data) Valid data time (1) 50 250 kHz 3.45 0.1 400 ns 0.9 µs 400 ns Cb = total capacitive of one bus in pF Switching Characteristics over operating free-air temperature range (unless otherwise noted) (see Figure 11 and Figure 12) PARAMETER FROM (INPUT) TO (OUTPUT) P port INT STANDARD MODE I2C BUS MIN MAX FAST MODE I2C BUS MIN UNIT MAX 4 µs 4 4 µs 200 200 ns tiv Interrupt valid time tir Interrupt reset delay time SCL INT tpv Output data valid SCL P7–P0 tps Input data setup time P port SCL 100 100 ns tph Input data hold time P port SCL 1 1 µs 12 Submit Documentation Feedback 4 PCA9534A REMOTE 8-BIT AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS I2C www.ti.com SCPS141B – SEPTEMBER 2006 – REVISED MARCH 2007 TYPICAL CHARACTERISTICS SUPPLY CURRENT vs TEMPERATURE QUIESCENT SUPPLY CURRENT vs TEMPERATURE 35 55 50 VCC = 5 V 30 ICC – Supply Current – nA ICC – Supply Current – µA 45 40 f SCL = 400 kHz I/Os unloaded 35 30 25 20 VCC = 3.3 V 15 10 VCC = 2.5 V VCC = 5 V 25 VCC = 3.3 V 20 15 VCC = 2.5 V 10 5 5 SCL = VCC 0 -40 -15 10 35 60 0 -40 85 10 35 60 TA – Free-Air Temperature – °C TA – Free-Air Temperature – °C SUPPLY CURRENT vs SUPPLY VOLTAGE SUPPLY CURRENT vs NUMBER OF I/Os HELD LOW 70 85 600 f SCL = 400 kHz I/Os unloaded 60 VCC = 5 V 550 500 ICC – Supply Current – µA ICC – Supply Current – µA -15 50 40 30 20 450 400 TA = –40°C 350 300 TA = 25°C 250 200 TA = 85°C 150 100 10 50 0 0 2.3 2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5 0 VCC – Supply Voltage – V 1 2 3 4 5 6 7 8 Number of I/Os Held Low Submit Documentation Feedback 13 PCA9534A REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS www.ti.com SCPS141B – SEPTEMBER 2006 – REVISED MARCH 2007 TYPICAL CHARACTERISTICS (continued) I/O OUTPUT LOW VOLTAGE vs TEMPERATURE I/O SINK CURRENT vs OUTPUT LOW VOLTAGE 30 300 250 VCC = 2.5 V VCC = 2.5 V, ISINK = 10 mA 25 ISINK – I/O Sink Current – mA VOL – Output Low Voltage – mV 275 225 200 175 150 VCC = 5 V, ISINK = 10 mA 125 100 VCC = 2.5 V, ISINK = 1 mA 75 50 VCC = 5 V, ISINK = 1 mA TA = –40°C 20 TA = 25°C 15 TA = 85°C 10 5 25 0 0 -40 -15 10 35 60 0.0 85 0.3 0.4 0.5 0.6 TA – Free-Air Temperature – °C I/O SINK CURRENT vs OUTPUT LOW VOLTAGE I/O SINK CURRENT vs OUTPUT LOW VOLTAGE 0.7 60 VCC = 3.3 V VCC = 5 V 55 35 50 ISINK – I/O Sink Current – mA TA = –40°C 30 25 TA = 25°C 20 15 TA = 85°C 10 45 TA = –40°C 40 35 TA = 25°C 30 25 TA = 85°C 20 15 10 5 5 0 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.0 0.1 0.2 0.3 0.4 0.5 VOL – Output Low Voltage – V VOL – Output Low Voltage – V 14 0.2 VOL – Output Low Voltage – V 40 ISINK – I/O Sink Current – mA 0.1 Submit Documentation Feedback 0.6 0.7 PCA9534A REMOTE 8-BIT AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS I2C www.ti.com SCPS141B – SEPTEMBER 2006 – REVISED MARCH 2007 TYPICAL CHARACTERISTICS (continued) I/O OUTPUT HIGH VOLTAGE vs TEMPERATURE I/O SOURCE CURRENT vs OUTPUT HIGH VOLTAGE 275 35 VCC = 2.5 V VCC = 2.5 V, IOL = 10 mA ISOURCE – I/O Source Current – mA (V CC – V OH ) – Output High Voltage – mV 250 225 200 175 150 125 VCC = 5 V, IOL = 10 mA 100 75 VCC = 2.5 V, IOL = 1 mA 50 VCC = 5 V, IOL = 1 mA 30 TA = –40°C 25 TA = 25°C 20 15 10 TA = 85°C 5 25 0 0 -40 0.0 -15 10 35 60 0.1 0.2 0.3 0.4 0.5 0.6 0.7 85 (VCC – VOH) – Output High Voltage – V TA – Free-Air Temperature – °C I/O SOURCE CURRENT vs OUTPUT HIGH VOLTAGE I/O SOURCE CURRENT vs OUTPUT HIGH VOLTAGE 75 70 50 ISOURCE – I/O Source Current – mA 45 40 ISOURCE – I/O Source Current – mA VCC = 3.3 V TA = –40°C 35 TA = 25°C 30 25 20 TA = 85°C 15 10 5 VCC = 5 V 65 60 55 50 TA = –40°C 45 40 35 30 TA = 25°C TA = 85°C 25 20 15 10 5 0 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.0 (VCC – VOH) – Output High Voltage – V Submit Documentation Feedback 0.1 0.2 0.3 0.4 0.5 0.6 0.7 (VCC – VOH) – Output High Voltage – V 15 PCA9534A REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS www.ti.com SCPS141B – SEPTEMBER 2006 – REVISED MARCH 2007 TYPICAL CHARACTERISTICS (continued) OUTPUT HIGH VOLTAGE vs SUPPLY VOLTAGE 6 TA = 25°C VOH – Output High Voltage – V 5 4 IOH = –8 mA 3 IOH = –10 mA 2 1 0 2.3 2.7 3.1 3.5 3.9 4.3 4.7 VCC – Supply Voltage – V 16 Submit Documentation Feedback 5.1 5.5 PCA9534A REMOTE 8-BIT AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS I2C www.ti.com SCPS141B – SEPTEMBER 2006 – REVISED MARCH 2007 PARAMETER MEASUREMENT INFORMATION VCC RL = 1 kΩ SDA DUT CL = 50 pF (see Note A) SDA LOAD CONFIGURATION Three Bytes for Complete Device Programming Stop Condition (P) Start Address Address Condition Bit 7 Bit 6 (S) (MSB) Address Bit 1 tscl R/W Bit 0 (LSB) ACK (A) Data Bit 07 (MSB) Data Bit 10 (LSB) Stop Condition (P) tsch 0.7 × VCC SCL 0.3 × VCC ticr tsts tPHL ticf tbuf tPLH tsp 0.7 × VCC SDA 0.3 × VCC ticf ticr tsth tsdh tsds tsps Repeat Start Condition Start or Repeat Start Condition Stop Condition VOLTAGE WAVEFORMS BYTE DESCRIPTION 1 I2C address 2, 3 P-port data A. CL includes probe and jig capacitance. B. All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns. C. All parameters and waveforms are not applicable to all devices. Figure 10. I2C Interface Load Circuit and Voltage Waveforms Submit Documentation Feedback 17 PCA9534A REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS www.ti.com SCPS141B – SEPTEMBER 2006 – REVISED MARCH 2007 PARAMETER MEASUREMENT INFORMATION (continued) VCC RL = 4.7 kΩ INT DUT CL = 100 pF (see Note A) INTERRUPT LOAD CONFIGURATION ACK From Slave Start Condition 8 Bits (One Data Byte) From Port R/W Slave Address S 0 1 1 1 A2 A1 A0 1 A 1 2 3 4 A 5 6 7 8 Data 1 ACK From Slave Data From Port A Data 2 1 A tir tir B B INT A tiv tsps A Data Into Port Address Data 1 0.7 × VCC INT 0.3 × VCC SCL Data 2 0.7 × VCC R/W tiv A 0.3 × VCC tir 0.7 × VCC Pn 0.7 × VCC INT 0.3 × VCC 0.3 × VCC View A−A View B−B A. CL includes probe and jig capacitance. B. All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns. C. All parameters and waveforms are not applicable to all devices. Figure 11. Interrupt Load Circuit and Voltage Waveforms 18 Submit Documentation Feedback P PCA9534A REMOTE 8-BIT AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS I2C www.ti.com SCPS141B – SEPTEMBER 2006 – REVISED MARCH 2007 PARAMETER MEASUREMENT INFORMATION (continued) Pn 500 W DUT CL = 50 pF (see Note A) 2 × VCC 500 W P-PORT LOAD CONFIGURATION SCL 0.7 × VCC P0 A P3 0.3 × VCC Slave ACK ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ SDA Pn tpv (see Note B) Unstable Data Last Stable Bit WRITE MODE (R/W = 0) SCL 0.7 × VCC P0 A tps P3 0.3 × VCC tph 0.7 × VCC Pn 0.3 × VCC READ MODE (R/W = 1) A. CL includes probe and jig capacitance. B. tpv is measured from 0.7 × VCC on SCL to 50% I/O (Pn) output. C. All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns. D. The outputs are measured one at a time, with one transition per measurement. E. All parameters and waveforms are not applicable to all devices. Figure 12. P-Port Load Circuit and Voltage Waveforms Submit Documentation Feedback 19 PCA9534A REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS www.ti.com SCPS141B – SEPTEMBER 2006 – REVISED MARCH 2007 PARAMETER MEASUREMENT INFORMATION (continued) VCC Pn RL = 1 kΩ DUT 500 W 2 × VCC DUT SDA CL = 50 pF (see Note A) 500 W CL = 50 pF (see Note A) SDA LOAD CONFIGURATION P-PORT LOAD CONFIGURATION Start SCL ACK or Read Cycle SDA 0.3 y VCC tRESET RESET VCC/2 tREC tw Pn VCC/2 tRESET A. CL includes probe and jig capacitance. B. All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns. C. I/Os are configured as inputs. D. All parameters and waveforms are not applicable to all devices. Figure 13. Reset Load Circuits and Voltage Waveforms 20 Submit Documentation Feedback PCA9534A REMOTE 8-BIT AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS I2C www.ti.com SCPS141B – SEPTEMBER 2006 – REVISED MARCH 2007 APPLICATION INFORMATION Figure 14 shows an application in which the PCA9534A can be used. VCC (5 V) 10 kW VCC Master Controller 10 kW 10 kW 2 kW 10 kW 100 kW (y3) VCC SDA SDA SCL SCL INT INT P0 P1 Subsystem 1 (e.g., Temperature Sensor) INT P2 RESET GND P3 Subsystem 2 (e.g., Counter) PCA9534A P4 A P5 A2 Controlled Device (e.g., CBT Device) P6 ENABLE A1 P7 B A0 GND ALARM Subsystem 3 (e.g., Alarm System) VCC A. Device address is configured as 0111100 for this example. B. P0, P2, and P3 are configured as outputs. C. P1, P4, and P5 are configured as inputs. D. P6 and P7 are not used and must be configured as outputs. Figure 14. Typical Application Submit Documentation Feedback 21 PCA9534A REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT AND CONFIGURATION REGISTERS www.ti.com SCPS141B – SEPTEMBER 2006 – REVISED MARCH 2007 APPLICATION INFORMATION (continued) Minimizing ICC When the I/O Controls LEDs When the I/Os are used to control LEDs, they are normally connected to VCC through a resistor as shown in Figure 14. Because the LED acts as a diode, when the LED is off, the I/O VIN is about 1.2 V less than VCC. The supply current, ICC, increases as VIN becomes lower than VCC and is specified as ∆ICC in Electrical Characteristics. For battery-powered applications, it is essential that the voltage of the I/O pins is greater than or equal to VCC when the LED is off to minimize current consumption. Figure 15 shows a high-value resistor in parallel with the LED. Figure 16 shows VCC less than the LED supply voltage by at least 1.2 V. Both of these methods maintain the I/O VIN at or above VCC and prevents additional supply-current consumption when the LED is off. VCC LED 100 kW VCC LEDx Figure 15. High-Value Resistor in Parallel With the LED 3.3 V VCC 5V LED LEDx Figure 16. Device Supplied by a Lower Voltage 22 Submit Documentation Feedback PACKAGE OPTION ADDENDUM www.ti.com 10-May-2007 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty PCA9534ADB ACTIVE SSOP DB 16 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCA9534ADBG4 ACTIVE SSOP DB 16 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCA9534ADBQR PREVIEW SSOP/ QSOP DBQ 16 2500 TBD Call TI PCA9534ADBR ACTIVE SSOP DB 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCA9534ADBRG4 ACTIVE SSOP DB 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCA9534ADGVR ACTIVE TVSOP DGV 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCA9534ADGVRG4 ACTIVE TVSOP DGV 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCA9534ADW ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCA9534ADWG4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCA9534ADWR ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCA9534ADWRG4 ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCA9534APW ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCA9534APWG4 ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCA9534APWR ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCA9534APWRG4 ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCA9534ARGTR PREVIEW QFN RGT 16 3000 TBD Call TI Call TI PCA9534ARGVR PREVIEW QFN RGV 16 2500 TBD Call TI Call TI Lead/Ball Finish MSL Peak Temp (3) Call TI (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 10-May-2007 (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 16-Jun-2007 TAPE AND REEL INFORMATION Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com Device 16-Jun-2007 Package Pins Site Reel Diameter (mm) Reel Width (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant PCA9534ADBR DB 16 MLA 330 16 8.2 6.6 2.5 12 16 Q1 PCA9534ADGVR DGV 16 MLA 330 12 6.8 4.0 1.6 8 16 Q1 PCA9534ADWR DW 16 TAI 330 16 10.75 10.7 2.7 12 16 Q1 PCA9534APWR PW 16 MLA 330 12 7.0 5.6 1.6 8 12 Q1 TAPE AND REEL BOX INFORMATION Device Package Pins Site Length (mm) Width (mm) Height (mm) PCA9534ADBR DB 16 MLA 342.9 336.6 28.58 PCA9534ADGVR DGV 16 MLA 342.9 336.6 20.64 PCA9534ADWR DW 16 TAI 346.0 346.0 33.0 PCA9534APWR PW 16 MLA 342.9 336.6 20.64 Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 16-Jun-2007 Pack Materials-Page 3 MECHANICAL DATA MPDS006C – FEBRUARY 1996 – REVISED AUGUST 2000 DGV (R-PDSO-G**) PLASTIC SMALL-OUTLINE 24 PINS SHOWN 0,40 0,23 0,13 24 13 0,07 M 0,16 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 0°–8° 1 0,75 0,50 12 A Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,08 14 16 20 24 38 48 56 A MAX 3,70 3,70 5,10 5,10 7,90 9,80 11,40 A MIN 3,50 3,50 4,90 4,90 7,70 9,60 11,20 DIM 4073251/E 08/00 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side. Falls within JEDEC: 24/48 Pins – MO-153 14/16/20/56 Pins – MO-194 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 28 PINS SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,25 0,09 8,20 7,40 5,60 5,00 Gage Plane 1 14 0,25 A 0°–ā8° 0,95 0,55 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 /E 12/01 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0°– 8° A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Telephony www.ti.com/telephony Low Power Wireless www.ti.com/lpw Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2007, Texas Instruments Incorporated