PIC12F508/509/16F505 Data Sheet 8/14-Pin, 8-Bit Flash Microcontrollers © 2009 Microchip Technology Inc. DS41236E Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, rfPIC and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MXDEV, MXLAB, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Octopus, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, PIC32 logo, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, UniWinDriver, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2009, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received ISO/TS-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. DS41236E-page 2 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 8/14-Pin, 8-Bit Flash Microcontrollers Devices Included In This Data Sheet: • PIC12F508 • PIC12F509 • PIC16F505 High-Performance RISC CPU: • Only 33 Single-Word Instructions to Learn • All Single-Cycle Instructions Except for Program Branches, which are Two-Cycle • 12-Bit Wide Instructions • 2-Level Deep Hardware Stack • Direct, Indirect and Relative Addressing modes for Data and Instructions • 8-Bit Wide Data Path • 8 Special Function Hardware Registers • Operating Speed: - DC – 20 MHz clock input (PIC16F505 only) - DC – 200 ns instruction cycle (PIC16F505 only) - DC – 4 MHz clock input - DC – 1000 ns instruction cycle Special Microcontroller Features: • 4 MHz Precision Internal Oscillator: - Factory calibrated to ±1% • In-Circuit Serial Programming™ (ICSP™) • In-Circuit Debugging (ICD) Support • Power-On Reset (POR) • Device Reset Timer (DRT) • Watchdog Timer (WDT) with Dedicated On-Chip RC Oscillator for Reliable Operation • Programmable Code Protection • Multiplexed MCLR Input Pin • Internal Weak Pull-Ups on I/O Pins • Power-Saving Sleep mode • Wake-Wp from Sleep on Pin Change • Selectable Oscillator Options: - INTRC: 4 MHz precision Internal oscillator - EXTRC: External low-cost RC oscillator - XT: Standard crystal/resonator - HS: High-speed crystal/resonator (PIC16F505 only) - LP: Power-saving, low-frequency crystal - EC: High-speed external clock input (PIC16F505 only) © 2009 Microchip Technology Inc. Low-Power Features/CMOS Technology: • Operating Current: - < 175 μA @ 2V, 4 MHz, typical • Standby Current: - 100 nA @ 2V, typical • Low-Power, High-Speed Flash Technology: - 100,000 Flash endurance - > 40 year retention • Fully Static Design • Wide Operating Voltage Range: 2.0V to 5.5V • Wide Temperature Range: - Industrial: -40°C to +85°C - Extended: -40°C to +125°C Peripheral Features (PIC12F508/509): • 6 I/O Pins: - 5 I/O pins with individual direction control - 1 input only pin - High current sink/source for direct LED drive - Wake-on-change - Weak pull-ups • 8-Bit Real-Time Clock/Counter (TMR0) with 8-Bit Programmable Prescaler Peripheral Features (PIC16F505): • 12 I/O Pins: - 11 I/O pins with individual direction control - 1 input only pin - High current sink/source for direct LED drive - Wake-on-change - Weak pull-ups • 8-Bit Real-Time Clock/Counter (TMR0) with 8-Bit Programmable Prescaler DS41236E-page 3 PIC12F508/509/16F505 Pin Diagrams PDIP, SOIC, MSOP 14 VSS RB5/OSC1/CLKIN 2 13 RB0/ICSPDAT RB4/OSC2/CLKOUT 3 12 RB1/ICSPCLK RB3/MCLR/VPP 11 RB2 RC5/T0CKI 4 5 10 RC0 RC4 6 9 RC1 RC3 7 8 RC2 PIC16F505 1 VDD VDD 1 GP5/OSC1/CLKIN 2 GP4/OSC2 3 GP3/MCLR/VPP 4 PIC12F508/509 PDIP, SOIC, TSSOP 8 VSS 7 GP0/ICSPDAT 6 GP1/ICSPCLK 5 GP2/T0CKI VDD 1 GP5/OSC1/CLKIN 2 GP4/OSC2 3 GP3/MCLR/VPP 4 PIC12F508/509 DFN 8 VSS 7 GP0/ICSPDAT 6 GP1/ICSPCLK 5 GP2/T0CKI DS41236E-page 4 RB5/OSC1/CLKIN 1 RB4/OSC2/CLKOUT 2 VDD NC NC VSS 16 15 14 13 PIC16F505 16-Pin Diagram (QFN) 12 RB0/ICSPDAT 11 RB1/ICSPCLK PIC16F505 8 RC0 RC1 9 7 4 RC2 RC5/TOCKI 6 RB2 RC3 10 5 3 RC4 RB3/MCLR/VPP © 2009 Microchip Technology Inc. PIC12F508/509/16F505 Program Memory Data Memory Device I/O Flash (words) SRAM (bytes) Timers 8-bit PIC12F508 512 25 6 1 PIC12F509 1024 41 6 1 PIC16F505 1024 72 12 1 © 2009 Microchip Technology Inc. DS41236E-page 5 PIC12F508/509/16F505 Table of Contents 1.0 General Description...................................................................................................................................................................... 7 2.0 PIC12F508/509/16F505 Device Varieties ................................................................................................................................... 9 3.0 Architectural Overview ............................................................................................................................................................... 11 4.0 Memory Organization ................................................................................................................................................................. 17 5.0 I/O Port ....................................................................................................................................................................................... 31 6.0 Timer0 Module and TMR0 Register ........................................................................................................................................... 35 7.0 Special Features Of The CPU .................................................................................................................................................... 41 8.0 Instruction Set Summary ............................................................................................................................................................ 57 9.0 Development Support................................................................................................................................................................. 65 10.0 Electrical Characteristics ............................................................................................................................................................ 69 11.0 DC and AC Characteristics Graphs and Charts ......................................................................................................................... 81 12.0 Packaging Information................................................................................................................................................................ 91 Index .................................................................................................................................................................................................. 105 The Microchip Web Site ..................................................................................................................................................................... 107 Customer Change Notification Service .............................................................................................................................................. 107 Customer Support .............................................................................................................................................................................. 107 Reader Response .............................................................................................................................................................................. 108 Product Identification System............................................................................................................................................................. 109 TO OUR VALUED CUSTOMERS It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and enhanced as new volumes and updates are introduced. If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via E-mail at [email protected] or fax the Reader Response Form in the back of this data sheet to (480) 792-4150. We welcome your feedback. Most Current Data Sheet To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000). Errata An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision of silicon and revision of document to which it applies. To determine if an errata sheet exists for a particular device, please check with one of the following: • Microchip’s Worldwide Web site; http://www.microchip.com • Your local Microchip sales office (see last page) • The Microchip Corporate Literature Center; U.S. FAX: (480) 792-7277 When contacting a sales office or the literature center, please specify which device, revision of silicon and data sheet (include literature number) you are using. Customer Notification System Register on our web site at www.microchip.com/cn to receive the most current information on all of our products. DS41236E-page 6 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 1.0 GENERAL DESCRIPTION The PIC12F508/509/16F505 devices from Microchip Technology are low-cost, high-performance, 8-bit, fully-static, Flash-based CMOS microcontrollers. They employ a RISC architecture with only 33 single-word/ single-cycle instructions. All instructions are single cycle (200 μs) except for program branches, which take two cycles. The PIC12F508/509/16F505 devices deliver performance an order of magnitude higher than their competitors in the same price category. The 12-bit wide instructions are highly symmetrical, resulting in a typical 2:1 code compression over other 8-bit microcontrollers in its class. The easy to use and easy to remember instruction set reduces development time significantly. 1.1 Applications The PIC12F508/509/16F505 devices fit in applications ranging from personal care appliances and security systems to low-power remote transmitters/receivers. The Flash technology makes customizing application programs (transmitter codes, appliance settings, receiver frequencies, etc.) extremely fast and convenient. The small footprint packages, for through hole or surface mounting, make these microcontrollers perfect for applications with space limitations. Low cost, low power, high performance, ease-of-use and I/O flexibility make the PIC12F508/509/16F505 devices very versatile even in areas where no microcontroller use has been considered before (e.g., timer functions, logic and PLDs in larger systems and coprocessor applications). The PIC12F508/509/16F505 products are equipped with special features that reduce system cost and power requirements. The Power-on Reset (POR) and Device Reset Timer (DRT) eliminate the need for external Reset circuitry. There are four oscillator configurations to choose from (six on the PIC16F505), including INTRC Internal Oscillator mode and the power-saving LP (Low-Power) Oscillator mode. Power-Saving Sleep mode, Watchdog Timer and code protection features improve system cost, power and reliability. The PIC12F508/509/16F505 devices are available in the cost-effective Flash programmable version, which is suitable for production in any volume. The customer can take full advantage of Microchip’s price leadership in Flash programmable microcontrollers, while benefiting from the Flash programmable flexibility. The PIC12F508/509/16F505 products are supported by a full-featured macro assembler, a software simulator, an in-circuit emulator, a ‘C’ compiler, a low-cost development programmer and a full featured programmer. All the tools are supported on IBM® PC and compatible machines. TABLE 1-1: PIC12F508/509/16F505 DEVICES PIC12F508 PIC12F509 PIC16F505 Clock Maximum Frequency of Operation (MHz) 4 4 20 Memory Flash Program Memory (words) 512 1024 1024 Data Memory (bytes) 25 41 72 TMR0 TMR0 TMR0 Yes Yes Yes I/O Pins 5 5 11 Input Pins 1 1 1 Internal Pull-ups Yes Yes Yes In-Circuit Serial Programming Yes Yes Yes Number of Instructions 33 33 33 8-pin PDIP, SOIC, MSOP, DFN 8-pin PDIP, SOIC, MSOP, DFN 14-pin PDIP, SOIC, TSSOP Peripherals Timer Module(s) Wake-up from Sleep on Pin Change Features Packages The PIC12F508/509/16F505 devices have Power-on Reset, selectable Watchdog Timer, selectable code-protect, high I/O current capability and precision internal oscillator. The PIC12F508/509/16F505 devices use serial programming with data pin RB0/GP0 and clock pin RB1/GP1. © 2009 Microchip Technology Inc. DS41236E-page 7 PIC12F508/509/16F505 NOTES: DS41236E-page 8 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 2.0 PIC12F508/509/16F505 DEVICE VARIETIES A variety of packaging options are available. Depending on application and production requirements, the proper device option can be selected using the information in this section. When placing orders, please use the PIC12F508/509/16F505 Product Identification System at the back of this data sheet to specify the correct part number. 2.1 2.2 Serialized Quick Turn ProgrammingSM (SQTPSM) Devices Microchip offers a unique programming service, where a few user-defined locations in each device are programmed with different serial numbers. The serial numbers may be random, pseudo-random or sequential. Serial programming allows each device to have a unique number, which can serve as an entry code, password or ID number. Quick Turn Programming (QTP) Devices Microchip offers a QTP programming service for factory production orders. This service is made available for users who choose not to program medium-to-high quantity units and whose code patterns have stabilized. The devices are identical to the Flash devices but with all Flash locations and fuse options already programmed by the factory. Certain code and prototype verification procedures do apply before production shipments are available. Please contact your local Microchip Technology sales office for more details. © 2009 Microchip Technology Inc. DS41236E-page 9 PIC12F508/509/16F505 NOTES: DS41236E-page 10 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 3.0 ARCHITECTURAL OVERVIEW The high performance of the PIC12F508/509/16F505 devices can be attributed to a number of architectural features commonly found in RISC microprocessors. To begin with, the PIC12F508/509/16F505 devices use a Harvard architecture in which program and data are accessed on separate buses. This improves bandwidth over traditional von Neumann architectures where program and data are fetched on the same bus. Separating program and data memory further allows instructions to be sized differently than the 8-bit wide data word. Instruction opcodes are 12 bits wide, making it possible to have all single-word instructions. A 12-bit wide program memory access bus fetches a 12-bit instruction in a single cycle. A two-stage pipeline overlaps fetch and execution of instructions. Consequently, all instructions (33) execute in a single cycle (200 ns @ 20 MHz, 1 μs @ 4 MHz) except for program branches. Table 3-1 below lists program memory (Flash) and data memory (RAM) for the PIC12F508/509/16F505 devices. TABLE 3-1: PIC12F508/509/16F505 MEMORY The PIC12F508/509/16F505 devices contain an 8-bit ALU and working register. The ALU is a general purpose arithmetic unit. It performs arithmetic and Boolean functions between data in the working register and any register file. The ALU is 8 bits wide and capable of addition, subtraction, shift and logical operations. Unless otherwise mentioned, arithmetic operations are two’s complement in nature. In two-operand instructions, one operand is typically the W (working) register. The other operand is either a file register or an immediate constant. In single operand instructions, the operand is either the W register or a file register. The W register is an 8-bit working register used for ALU operations. It is not an addressable register. Depending on the instruction executed, the ALU may affect the values of the Carry (C), Digit Carry (DC) and Zero (Z) bits in the STATUS register. The C and DC bits operate as a borrow and digit borrow out bit, respectively, in subtraction. See the SUBWF and ADDWF instructions for examples. Simplified block diagrams are shown in Figure 3-1 and Figure 3-2, with the corresponding pin described in Table 3-2 and Table 3-3. Memory Device Program Data PIC12F508 512 x 12 25 x 8 PIC12F509 1024 x 12 41 x 8 PIC16F505 1024 x 12 72 x 8 The PIC12F508/509/16F505 devices can directly or indirectly address its register files and data memory. All Special Function Registers (SFR), including the PC, are mapped in the data memory. The PIC12F508/509/ 16F505 devices have a highly orthogonal (symmetrical) instruction set that makes it possible to carry out any operation, on any register, using any addressing mode. This symmetrical nature and lack of “special optimal situations” make programming with the PIC12F508/509/16F505 devices simple, yet efficient. In addition, the learning curve is reduced significantly. © 2009 Microchip Technology Inc. DS41236E-page 11 PIC12F508/509/16F505 FIGURE 3-1: PIC12F508/509 BLOCK DIAGRAM 12 Flash 512 x 12 or 1024 x 12 Program Memory 8 Data Bus Program Counter GP0/ISCPDAT GP1/ISCPCLK GP2/T0CKI GP3/MCLR/VPP GP4/OSC2 GP5/OSC1/CLKIN RAM 25 x 8 or 41 x 8 File Registers Stack 1 Stack 2 Program 12 Bus RAM Addr GPIO 9 Addr MUX Instruction Reg Direct Addr 5 5-7 Indirect Addr FSR Reg Status Reg 8 3 MUX Device Reset Timer Instruction Decode and Control OSC1/CLKIN OSC2 Timing Generation Internal RC OSC Power-on Reset Watchdog Timer ALU 8 W Reg Timer0 MCLR VDD, VSS DS41236E-page 12 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 TABLE 3-2: PIC12F508/509 PINOUT DESCRIPTION Name GP0/ICSPDAT GP1/ICSPCLK GP2/T0CKI GP3/MCLR/VPP GP4/OSC2 GP5/OSC1/CLKIN Function Input Type Output Type GP0 TTL CMOS Bidirectional I/O pin. Can be software programmed for internal weak pull-up and wake-up from Sleep on pin change. ICSPDAT ST CMOS In-Circuit Serial Programming™ data pin. GP1 TTL CMOS Bidirectional I/O pin. Can be software programmed for internal weak pull-up and wake-up from Sleep on pin change. ICSPCLK ST CMOS In-Circuit Serial Programming clock pin. CMOS Bidirectional I/O pin. Description GP2 TTL T0CKI ST — Clock input to TMR0. GP3 TTL — Input pin. Can be software programmed for internal weak pull-up and wake-up from Sleep on pin change. MCLR ST — Master Clear (Reset). When configured as MCLR, this pin is an active-low Reset to the device. Voltage on MCLR/VPP must not exceed VDD during normal device operation or the device will enter Programming mode. Weak pull-up always on if configured as MCLR. — Programming voltage input. VPP HV GP4 TTL OSC2 — CMOS Bidirectional I/O pin. XTAL GP5 TTL OSC1 XTAL — Oscillator crystal output. Connections to crystal or resonator in Crystal Oscillator mode (XT and LP modes only, GPIO in other modes). CMOS Bidirectional I/O pin. Oscillator crystal input. CLKIN ST — External clock source input. VDD VDD — P Positive supply for logic and I/O pins. VSS VSS — P Ground reference for logic and I/O pins. Legend: I = Input, O = Output, I/O = Input/Output, P = Power, — = Not used, TTL = TTL input, ST = Schmitt Trigger input, HV = High Voltage © 2009 Microchip Technology Inc. DS41236E-page 13 PIC12F508/509/16F505 FIGURE 3-2: PIC16F505 BLOCK DIAGRAM 12 Flash 1K x 12 Program Memory 8 Data Bus Program Counter RB0/ICSPCLK RB1/ICSPDAT RB2 RB3/MCLR/VPP RB4/OSC2/CLKOUT RB5/OSC1/CLKIN RAM 72 bytes File Registers Stack 1 Stack 2 Program 12 Bus RAM Addr 9 PORTC Addr MUX Instruction Reg Direct Addr 5 5-7 Indirect Addr FSR Reg Status Reg 8 3 Device Reset Timer Instruction Decode and Control OSC1/CLKIN OSC2/CLKOUT Timing Generation PORTB Power-on Reset RC0 RC1 RC2 RC3 RC4 RC5/T0CKI MUX ALU 8 Watchdog Timer W Reg Internal RC OSC Timer0 MCLR VDD, VSS DS41236E-page 14 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 TABLE 3-3: PIC16F505 PINOUT DESCRIPTION Name RB0/ICSPDAT RB1/ICSPCLK Function Input Type Output Type RB0 TTL CMOS Bidirectional I/O pin. Can be software programmed for internal weak pull-up and wake-up from Sleep on pin change. ICSPDAT ST CMOS In-Circuit Serial Programming™ data pin. RB1 TTL CMOS Bidirectional I/O pin. Can be software programmed for internal weak pull-up and wake-up from Sleep on pin change. ICSPCLK ST CMOS In-Circuit Serial Programming clock pin. CMOS Bidirectional I/O pin. Description RB2 RB2 TTL RB3/MCLR/VPP RB3 TTL — Input port. Can be software programmed for internal weak pull-up and wake-up from Sleep on pin change. MCLR ST — Master Clear (Reset). When configured as MCLR, this pin is an active-low Reset to the device. Voltage on MCLR/VPP must not exceed VDD during normal device operation or the device will enter Programming mode. Weak pull-up always on if configured as MCLR. VPP HV — Programming voltage input. RB4 TTL OSC2 — XTAL CLKOUT — CMOS In EXTRC and INTRC modes, the pin output can be configured for CLKOUT, which has 1/4 the frequency of OSC1 and denotes the instruction cycle rate. RB5 TTL RB4/OSC2/CLKOUT RB5/OSC1/CLKIN CMOS Bidirectional I/O pin. Can be software programmed for internal weak pull-up and wake-up from Sleep on pin change. Oscillator crystal output. Connections to crystal or resonator in Crystal Oscillator mode (XT, HS and LP modes only). CMOS Bidirectional I/O pin. OSC1 XTAL — Crystal input. CLKIN ST — External clock source input. RC0 RC0 TTL CMOS Bidirectional I/O pin. RC1 RC1 TTL CMOS Bidirectional I/O pin. RC2 RC2 TTL CMOS Bidirectional I/O pin. RC3 RC3 TTL CMOS Bidirectional I/O pin. RC4 RC4 TTL CMOS Bidirectional I/O pin. RC5/T0CKI RC5 TTL CMOS Bidirectional I/O pin. T0CKI ST — Clock input to TMR0. VDD VDD — P Positive supply for logic and I/O pins. VSS VSS — P Ground reference for logic and I/O pins. Legend: I = Input, O = Output, I/O = Input/Output, P = Power, — = Not used, TTL = TTL input, ST = Schmitt Trigger input, HV = High Voltage © 2009 Microchip Technology Inc. DS41236E-page 15 PIC12F508/509/16F505 3.1 Clocking Scheme/Instruction Cycle 3.2 Instruction Flow/Pipelining An instruction cycle consists of four Q cycles (Q1, Q2, Q3 and Q4). The instruction fetch and execute are pipelined such that fetch takes one instruction cycle, while decode and execute take another instruction cycle. However, due to the pipelining, each instruction effectively executes in one cycle. If an instruction causes the PC to change (e.g., GOTO), then two cycles are required to complete the instruction (Example 3-1). The clock input (OSC1/CLKIN pin) is internally divided by four to generate four non-overlapping quadrature clocks, namely Q1, Q2, Q3 and Q4. Internally, the PC is incremented every Q1 and the instruction is fetched from program memory and latched into the instruction register in Q4. It is decoded and executed during the following Q1 through Q4. The clocks and instruction execution flow is shown in Figure 3-3 and Example 3-1. A fetch cycle begins with the PC incrementing in Q1. In the execution cycle, the fetched instruction is latched into the Instruction Register (IR) in cycle Q1. This instruction is then decoded and executed during the Q2, Q3 and Q4 cycles. Data memory is read during Q2 (operand read) and written during Q4 (destination write). FIGURE 3-3: CLOCK/INSTRUCTION CYCLE Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 OSC1 Q1 Q2 Internal phase clock Q3 Q4 PC PC PC + 1 Fetch INST (PC) Execute INST (PC – 1) EXAMPLE 3-1: PC + 2 Fetch INST (PC + 1) Execute INST (PC) Fetch INST (PC + 2) Execute INST (PC + 1) INSTRUCTION PIPELINE FLOW 1. MOVLW 03H 2. MOVWF PORTB 3. CALL SUB_1 4. BSF PORTB, BIT1 Fetch 1 Execute 1 Fetch 2 Execute 2 Fetch 3 Execute 3 Fetch 4 Flush Fetch SUB_1 Execute SUB_1 All instructions are single cycle, except for any program branches. These take two cycles, since the fetch instruction is “flushed” from the pipeline, while the new instruction is being fetched and then executed. DS41236E-page 16 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 4.0 MEMORY ORGANIZATION The PIC12F508/509/16F505 memories are organized into program memory and data memory. For devices with more than 512 bytes of program memory, a paging scheme is used. Program memory pages are accessed using one STATUS register bit. For the PIC12F509 and PIC16F505, with data memory register files of more than 32 registers, a banking scheme is used. Data memory banks are accessed using the File Select Register (FSR). FIGURE 4-1: PROGRAM MEMORY MAP AND STACK FOR THE PIC12F508/509 PC<11:0> 12 CALL, RETLW Stack Level 1 Stack Level 2 Reset Vector(1) Program Memory Organization for the PIC12F508/509 The PIC12F508 device has a 10-bit Program Counter (PC) and PIC12F509 has a 11-bit Program Counter (PC) capable of addressing a 2K x 12 program memory space. Only the first 512 x 12 (0000h-01FFh) for the PIC12F508, and 1K x 12 (0000h-03FFh) for the PIC12F509 are physically implemented (see Figure 4-1). Accessing a location above these boundaries will cause a wrap-around within the first 512 x 12 space (PIC12F508) or 1K x 12 space (PIC12F509). The effective Reset vector is a 0000h (see Figure 4-1). Location 01FFh (PIC12F508) and location 03FFh (PIC12F509) contain the internal clock oscillator calibration value. This value should never be overwritten. On-chip Program Memory User Memory Space 4.1 512 Word 01FFh 0200h On-chip Program Memory 1024 Word 03FFh 0400h 7FFh Note 1: © 2009 Microchip Technology Inc. 0000h Address 0000h becomes the effective Reset vector. Location 01FFh, 03FFh (PIC12F508, PIC12F509) contains the MOVLW XX internal oscillator calibration value. DS41236E-page 17 PIC12F508/509/16F505 4.2 Program Memory Organization For The PIC16F505 The PIC16F505 device has a 11-bit Program Counter (PC) capable of addressing a 2K x 12 program memory space. The 1K x 12 (0000h-03FFh) for the PIC16F505 are physically implemented. Refer to Figure 4-2. Accessing a location above this boundary will cause a wrap-around within the first 1K x 12 space. The effective Reset vector is at 0000h (see Figure 4-2). Location 03FFh contains the internal oscillator calibration value. This value should never be overwritten. FIGURE 4-2: PROGRAM MEMORY MAP AND STACK FOR THE PIC16F505 PC<11:0> Stack Level 1 Stack Level 2 Reset Vector(1) Data Memory Organization Data memory is composed of registers or bytes of RAM. Therefore, data memory for a device is specified by its register file. The register file is divided into two functional groups: Special Function Registers (SFR) and General Purpose Registers (GPR). The Special Function Registers include the TMR0 register, the Program Counter (PCL), the STATUS register, the I/O registers (ports) and the File Select Register (FSR). In addition, Special Function Registers are used to control the I/O port configuration and prescaler options. The General Purpose Registers are used for data and control information under command of the instructions. For the PIC12F508/509, the register file is composed of 7 Special Function Registers, 9 General Purpose Registers and 16 or 32 General Purpose Registers accessed by banking (see Figure 4-3 and Figure 4-4). For the PIC16F505, the register file is composed of 8 Special Function Registers, 8 General Purpose Registers and 64 General Purpose Registers accessed by banking (Figure 4-5). 12 CALL, RETLW 4.3 4.3.1 0000h GENERAL PURPOSE REGISTER FILE User Memory Space The General Purpose Register file is accessed, either directly or indirectly, through the File Select Register (FSR). See Section 4.9 “Indirect Data Addressing: INDF and FSR Registers”. 01FFh 0200h On-chip Program Memory 1024 Words 03FFh 0400h 7FFh Note 1: Address 0000h becomes the effective Reset vector. Location 03FFh contains the MOVLW XX internal oscillator calibration value. DS41236E-page 18 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 FIGURE 4-3: PIC12F508 REGISTER FILE MAP FIGURE 4-4: PIC12F509 REGISTER FILE MAP FSR<5> File Address 0 1 File Address 00h INDF(1) 01h TMR0 02h PCL 03h STATUS 04h FSR 05h OSCCAL 06h GPIO 07h 00h INDF(1) 01h TMR0 02h PCL 03h STATUS 04h FSR 05h OSCCAL 06h GPIO 20h Addresses map back to addresses in Bank 0. 07h General Purpose Registers General Purpose Registers 2Fh 0Fh 10h 30h General Purpose Registers 1Fh 1Fh 3Fh Bank 0 Note 1: Note 1: Not a physical register. See Section 4.9 “Indirect Data Addressing: INDF and FSR Registers”. FIGURE 4-5: General Purpose Registers Bank 1 Not a physical register. See Section 4.9 “Indirect Data Addressing: INDF and FSR Registers”. PIC16F505 REGISTER FILE MAP FSR<6:5> 00 File Address 00h INDF(1) 01h TMR0 02h PCL 03h STATUS 04h FSR 05h OSCCAL 06h PORTB 07h PORTC 08h General Purpose Registers 0Fh 10h 20h 60h 2Fh 4Fh 6Fh 30h 50h 70h General Purpose Registers 3Fh Bank 0 Note 1: 40h 11 Addresses map back to addresses in Bank 0. General Purpose Registers 1Fh 10 01 General Purpose Registers 5Fh Bank 1 General Purpose Registers 7Fh Bank 2 Bank 3 Not a physical register. See Section 4.9 “Indirect Data Addressing: INDF and FSR Registers”. © 2009 Microchip Technology Inc. DS41236E-page 19 PIC12F508/509/16F505 4.3.2 SPECIAL FUNCTION REGISTERS The Special Function Registers (SFRs) are registers used by the CPU and peripheral functions to control the operation of the device (Table 4-1). The Special Function Registers can be classified into two sets. The Special Function Registers associated with the “core” functions are described in this section. Those related to the operation of the peripheral features are described in the section for each peripheral feature. TABLE 4-1: Address SPECIAL FUNCTION REGISTER (SFR) SUMMARY (PIC12F508/509) Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on Power-On Reset(2) Page # 00h INDF Uses Contents of FSR to Address Data Memory (not a physical register) xxxx xxxx 28 01h TMR0 8-bit Real-Time Clock/Counter xxxx xxxx 35 02h(1) PCL Low-order 8 bits of PC 1111 1111 27 — (5) PA0 TO PD Z DC C (3) 22 03h STATUS GPWUF 04h FSR Indirect Data Memory Address Pointer 111x xxxx 28 04h(4) FSR Indirect Data Memory Address Pointer 110x xxxx 28 05h OSCCAL CAL6 CAL5 06h GPIO — — N/A TRISGPIO — — N/A OPTION GPWU 0-01 1xxx CAL4 CAL3 CAL2 CAL1 CAL0 — 1111 111- 26 GP5 GP4 GP3 GP2 GP1 GP0 --xx xxxx 31 --11 1111 31 1111 1111 24 I/O Control Register GPPU TOCS TOSE PSA PS2 PS1 PS0 Legend: – = unimplemented, read as ‘0’, x = unknown, u = unchanged, q = value depends on condition. Note 1: The upper byte of the Program Counter is not directly accessible. See Section 4.7 “Program Counter” for an explanation of how to access these bits. 2: Other (non Power-up) Resets include external Reset through MCLR, Watchdog Timer and wake-up on pin change Reset. 3: If Reset was due to wake-up on pin change, then bit 7 = 1. All other Resets will cause bit 7 = 0. 4: PIC12F509 only. 5: This bit is used on the PIC12F509. For code compatibility do not use this bit on the PIC12F508. DS41236E-page 20 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 TABLE 4-2: Address SPECIAL FUNCTION REGISTER (SFR) SUMMARY (PIC16F505) Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on Power-On Reset(2) Page # 00h INDF Uses Contents of FSR to Address Data Memory (not a physical register) xxxx xxxx 28 01h TMR0 8-bit Real-Time Clock/Counter xxxx xxxx 35 02h(1) PCL Low-order 8 bits of PC 1111 1111 27 03h STATUS RBWUF 0-01 1xxx 22 Indirect Data Memory Address Pointer 04h FSR 05h OSCCAL 06h 07h — PA0 CAL4 TO Z DC C 100x xxxx 28 CAL2 CAL1 CAL0 — 1111 111- 26 CAL6 CAL5 PORTB — — RB5 RB4 RB3 RB2 RB1 RB0 --xx xxxx 31 PORTC — — RC5 RC4 RC3 RC2 RC1 RC0 --xx xxxx 31 N/A TRISB — — I/O Control Register --11 1111 31 N/A TRISC — — I/O Control Register --11 1111 31 N/A OPTION RBWU RBPU 1111 1111 25 TOCS CAL3 PD TOSE PSA PS2 PS1 PS0 Legend: – = unimplemented, read as ‘0’, x = unknown, u = unchanged, q = value depends on condition. Note 1: If Reset was due to wake-up on pin change, then bit 7 = 1. All other Resets will cause bit 7 = 0. 2: Other (non Power-up) Resets include external reset through MCLR, Watchdog Timer and wake-up on pin change Reset. © 2009 Microchip Technology Inc. DS41236E-page 21 PIC12F508/509/16F505 4.4 STATUS Register For example, CLRF STATUS, will clear the upper three bits and set the Z bit. This leaves the STATUS register as 000u u1uu (where u = unchanged). This register contains the arithmetic status of the ALU, the Reset status and the page preselect bit. Therefore, it is recommended that only BCF, BSF and MOVWF instructions be used to alter the STATUS register. These instructions do not affect the Z, DC or C bits from the STATUS register. For other instructions which do affect Status bits, see Section 8.0 “Instruction Set Summary”. The STATUS register can be the destination for any instruction, as with any other register. If the STATUS register is the destination for an instruction that affects the Z, DC or C bits, then the write to these three bits is disabled. These bits are set or cleared according to the device logic. Furthermore, the TO and PD bits are not writable. Therefore, the result of an instruction with the STATUS register as destination may be different than intended. REGISTER 4-1: STATUS REGISTER (ADDRESS: 03h) (PIC12F508/509) R/W-0 R/W-0 R/W-0 R-1 R-1 R/W-x R/W-x R/W-x GPWUF — PA0 TO PD Z DC C bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 GPWUF: GPIO Reset bit 1 = Reset due to wake-up from Sleep on pin change 0 = After power-up or other Reset bit 6 Reserved: Do not use bit 5 PA0: Program Page Preselect bits(1) 1 = Page 1 (200h-3FFh) 0 = Page 0 (000h-1FFh) Each page is 512 bytes. Using the PA0 bit as a general purpose read/write bit in devices which do not use it for program page preselect is not recommended, since this may affect upward compatibility with future products. bit 4 TO: Time-Out bit 1 = After power-up, CLRWDT instruction, or SLEEP instruction 0 = A WDT time-out occurred bit 3 PD: Power-Down bit 1 = After power-up or by the CLRWDT instruction 0 = By execution of the SLEEP instruction bit 2 Z: Zero bit 1 = The result of an arithmetic or logic operation is zero 0 = The result of an arithmetic or logic operation is not zero bit 1 DC: Digit Carry/Borrow bit (for ADDWF and SUBWF instructions) ADDWF: 1 = A carry from the 4th low-order bit of the result occurred 0 = A carry from the 4th low-order bit of the result did not occur SUBWF: 1 = A borrow from the 4th low-order bit of the result did not occur 0 = A borrow from the 4th low-order bit of the result occurred bit 0 C: Carry/Borrow bit (for ADDWF, SUBWF and RRF, RLF instructions) SUBWF: RRF or RLF: ADDWF: 1 = A carry occurred 1 = A borrow did not occur Load bit with LSb or MSb, respectively 0 = A carry did not occur 0 = A borrow occurred Note 1: This bit is used on the PIC12F509. For code compatibility do not use this bit on the PIC12F508. DS41236E-page 22 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 REGISTER 4-2: STATUS REGISTER (ADDRESS: 03h) (PIC16F505) R/W-0 R/W-0 R/W-0 R-1 R-1 R/W-x R/W-x R/W-x RBWUF — PA0 TO PD Z DC C bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 RBWUF: PORTB Reset bit 1 = Reset due to wake-up from Sleep on pin change 0 = After power-up or other Reset bit 6 Reserved: Do not use bit 5 PA0: Program Page Preselect bits 1 = Page 1 (200h-3FFh) 0 = Page 0 (000h-1FFh) Each page is 512 bytes. Using the PA0 bit as a general purpose read/write bit in devices which do not use it for program page preselect is not recommended, since this may affect upward compatibility with future products. bit 4 TO: Time-Out bit 1 = After power-up, CLRWDT instruction, or SLEEP instruction 0 = A WDT time-out occurred bit 3 PD: Power-Down bit 1 = After power-up or by the CLRWDT instruction 0 = By execution of the SLEEP instruction bit 2 Z: Zero bit 1 = The result of an arithmetic or logic operation is zero 0 = The result of an arithmetic or logic operation is not zero bit 1 DC: Digit Carry/Borrow bit (for ADDWF and SUBWF instructions) ADDWF: 1 = A carry from the 4th low-order bit of the result occurred 0 = A carry from the 4th low-order bit of the result did not occur SUBWF: 1 = A borrow from the 4th low-order bit of the result did not occur 0 = A borrow from the 4th low-order bit of the result occurred bit 0 C: Carry/Borrow bit (for ADDWF, SUBWF and RRF, RLF instructions) ADDWF: SUBWF: RRF or RLF: 1 = A carry occurred 1 = A borrow did not occur Load bit with LSb or MSb, respectively 0 = A carry did not occur 0 = A borrow occurred © 2009 Microchip Technology Inc. DS41236E-page 23 PIC12F508/509/16F505 4.5 OPTION Register The OPTION register is a 8-bit wide, write-only register, which contains various control bits to configure the Timer0/WDT prescaler and Timer0. Note: If TRIS bit is set to ‘0’, the wake-up on change and pull-up functions are disabled for that pin (i.e., note that TRIS overrides Option control of GPPU/RBPU and GPWU/RBWU). Note: If the T0CS bit is set to ‘1’, it will override the TRIS function on the T0CKI pin. By executing the OPTION instruction, the contents of the W register will be transferred to the OPTION register. A Reset sets the OPTION<7:0> bits. REGISTER 4-3: OPTION REGISTER (PIC12F508/509) W-1 W-1 W-1 W-1 W-1 W-1 W-1 W-1 GPWU GPPU T0CS T0SE PSA PS2 PS1 PS0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 GPWU: Enable Wake-up on Pin Change bit (GP0, GP1, GP3) 1 = Disabled 0 = Enabled bit 6 GPPU: Enable Weak Pull-ups bit (GP0, GP1, GP3) 1 = Disabled 0 = Enabled bit 5 T0CS: Timer0 Clock Source Select bit 1 = Transition on T0CKI pin (overrides TRIS on the T0CKI pin) 0 = Transition on internal instruction cycle clock, FOSC/4 bit 4 T0SE: Timer0 Source Edge Select bit 1 = Increment on high-to-low transition on the T0CKI pin 0 = Increment on low-to-high transition on the T0CKI pin bit 3 PSA: Prescaler Assignment bit 1 = Prescaler assigned to the WDT 0 = Prescaler assigned to Timer0 bit 2-0 PS<2:0>: Prescaler Rate Select bits Bit Value 000 001 010 011 100 101 110 111 DS41236E-page 24 x = Bit is unknown Timer0 Rate WDT Rate 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128 1 : 256 1:1 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 REGISTER 4-4: OPTION REGISTER (PIC16F505) W-1 W-1 W-1 W-1 W-1 W-1 W-1 W-1 RBWU RBPU T0CS T0SE PSA PS2 PS1 PS0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7 RBWU: Enable Wake-up on Pin Change bit (RB0, RB1, RB3, RB4) 1 = Disabled 0 = Enabled bit 6 RBPU: Enable Weak Pull-ups bit (RB0, RB1, RB3, RB4) 1 = Disabled 0 = Enabled bit 5 T0CS: Timer0 clock Source Select bit 1 = Transition on T0CKI pin (overrides TRIS on the T0CKI pin) 0 = Transition on internal instruction cycle clock, FOSC/4 bit 4 T0SE: Timer0 Source Edge Select bit 1 = Increment on high-to-low transition on the T0CKI pin 0 = Increment on low-to-high transition on the T0CKI pin bit 3 PSA: Prescaler Assignment bit 1 = Prescaler assigned to the WDT 0 = Prescaler assigned to Timer0 bit 2-0 PS<2:0>: Prescaler Rate Select bits Bit Value 000 001 010 011 100 101 110 111 © 2009 Microchip Technology Inc. x = Bit is unknown Timer0 Rate WDT Rate 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128 1 : 256 1:1 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128 DS41236E-page 25 PIC12F508/509/16F505 4.6 OSCCAL Register The Oscillator Calibration (OSCCAL) register is used to calibrate the internal precision 4 MHz oscillator. It contains seven bits for calibration. Note: After you move in the calibration constant, do not change the value. See Section 7.2.5 “Internal 4 MHz RC Oscillator”. Erasing the device will also erase the preprogrammed internal calibration value for the internal oscillator. The calibration value must be read prior to erasing the part so it can be reprogrammed correctly later. REGISTER 4-5: OSCCAL REGISTER (ADDRESS: 05h) R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-0 CAL6 CAL5 CAL4 CAL3 CAL2 CAL1 CAL0 — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-1 CAL<6:0>: Oscillator Calibration bits 0111111 = Maximum frequency • • • 0000001 0000000 = Center frequency 1111111 • • • 1000000 = Minimum frequency bit 0 Unimplemented: Read as ‘0’ DS41236E-page 26 x = Bit is unknown © 2009 Microchip Technology Inc. PIC12F508/509/16F505 4.7 4.7.1 Program Counter EFFECTS OF RESET As a program instruction is executed, the Program Counter (PC) will contain the address of the next program instruction to be executed. The PC value is increased by one every instruction cycle, unless an instruction changes the PC. The PC is set upon a Reset, which means that the PC addresses the last location in the last page (i.e., the oscillator calibration instruction). After executing MOVLW XX, the PC will roll over to location 00h and begin executing user code. For a GOTO instruction, bits 8:0 of the PC are provided by the GOTO instruction word. The Program Counter (PCL) is mapped to PC<7:0>. Bit 5 of the STATUS register provides page information to bit 9 of the PC (Figure 4-6). The STATUS register page preselect bits are cleared upon a Reset, which means that page 0 is pre-selected. For a CALL instruction, or any instruction where the PCL is the destination, bits 7:0 of the PC again are provided by the instruction word. However, PC<8> does not come from the instruction word, but is always cleared (Figure 4-6). Instructions where the PCL is the destination, or modify PCL instructions, include MOVWF PC, ADDWF PC and BSF PC,5. Note: Because PC<8> is cleared in the CALL instruction or any modify PCL instruction, all subroutine calls or computed jumps are limited to the first 256 locations of any program memory page (512 words long). FIGURE 4-6: LOADING OF PC BRANCH INSTRUCTIONS GOTO Instruction 11 10 9 8 7 PC 0 PCL 4.8 Stack The PIC12F508/509/16F505 devices have a 2-deep, 12-bit wide hardware PUSH/POP stack. A CALL instruction will PUSH the current value of Stack 1 into Stack 2 and then PUSH the current PC value, incremented by one, into Stack Level 1. If more than two sequential CALLs are executed, only the most recent two return addresses are stored. A RETLW instruction will POP the contents of Stack Level 1 into the PC and then copy Stack Level 2 contents into Stack Level 1. If more than two sequential RETLWs are executed, the stack will be filled with the address previously stored in Stack Level 2. Note that the W register will be loaded with the literal value specified in the instruction. This is particularly useful for the implementation of data look-up tables within the program memory. Note 1: There are no Status bits to indicate stack overflows or stack underflow conditions. 2: There are no instruction mnemonics called PUSH or POP. These are actions that occur from the execution of the CALL and RETLW instructions. Instruction Word 7 Therefore, upon a Reset, a GOTO instruction will automatically cause the program to jump to page 0 until the value of the page bits is altered. PA0 0 Status CALL or Modify PCL Instruction 11 10 9 8 7 PC 0 PCL 7 Instruction Word Reset to ‘0’ PA0 0 Status © 2009 Microchip Technology Inc. DS41236E-page 27 PIC12F508/509/16F505 4.9 EXAMPLE 4-1: Indirect Data Addressing: INDF and FSR Registers The INDF register is not a physical register. Addressing INDF actually addresses the register whose address is contained in the FSR register (FSR is a pointer). This is indirect addressing. 4.9.1 NEXT MOVLW MOVWF CLRF INCF BTFSC GOTO CONTINUE : : INDIRECT ADDRESSING • • • • Register file 07 contains the value 10h Register file 08 contains the value 0Ah Load the value 07 into the FSR register A read of the INDF register will return the value of 10h • Increment the value of the FSR register by one (FSR = 08) • A read of the INDR register now will return the value of 0Ah. HOW TO CLEAR RAM USING INDIRECT ADDRESSING 0x10 FSR INDF ;initialize pointer ;to RAM ;clear INDF ;register ;inc pointer ;all done? ;NO, clear next FSR,F FSR,4 NEXT ;YES, continue The FSR is a 5-bit wide register. It is used in conjunction with the INDF register to indirectly address the data memory area. Reading INDF itself indirectly (FSR = 0) will produce 00h. Writing to the INDF register indirectly results in a no operation (although Status bits may be affected). A simple program to clear RAM locations 10h-1Fh using indirect addressing is shown in Example 4-1. The FSR<4:0> bits are used to select data memory addresses 00h to 1Fh. PIC12F508 – Does not use banking. FSR <7:5> are unimplemented and read as ‘1’s. PIC12F509 – Uses FSR<5>. Selects between bank 0 and bank 1. FSR<7:6> are unimplemented, read as ‘1’. PIC16F505 – Uses FSR<6:5>. Selects from bank 0 to bank 3. FSR<7> is unimplemented, read as ‘1’. FIGURE 4-7: DIRECT/INDIRECT ADDRESSING (PIC12F508/509) Direct Addressing (FSR) 6 5 Bank Select 4 Indirect Addressing (opcode) 0 6 Location Select 5 4 Bank 00 (FSR) 0 Location Select 01 00h Addresses map back to addresses in Bank 0. Data Memory(1) 0Fh 10h 1Fh Bank 0 Note 1: 2: 3Fh Bank 1(2) For register map detail, see Section 4.3 “Data Memory Organization”. PIC12F509. DS41236E-page 28 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 FIGURE 4-8: DIRECT/INDIRECT ADDRESSING (PIC16F505) Direct Addressing (FSR) 6 5 Bank Select 4 Indirect Addressing (opcode) 0 6 Location Select 01 10 00h (FSR) 0 Location Select 11 Addresses map back to addresses in Bank 0. 0Fh 10h 1Fh Bank 0 Note 1: 4 Bank 00 Data Memory(1) 5 3Fh Bank 1 5Fh Bank 2 7Fh Bank 3 For register map detail, see Section 4.3 “Data Memory Organization”. © 2009 Microchip Technology Inc. DS41236E-page 29 PIC12F508/509/16F505 NOTES: DS41236E-page 30 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 5.0 I/O PORT As with any other register, the I/O register(s) can be written and read under program control. However, read instructions (e.g., MOVF PORTB,W) always read the I/O pins independent of the pin’s Input/Output modes. On Reset, all I/O ports are defined as input (inputs are at high-impedance) since the I/O control registers are all set. Note: 5.1 On the PIC12F508/509, I/O PORTB is referenced as GPIO. On the PIC16F505, I/O PORTB is referenced as PORTB. The equivalent circuit for an I/O port pin is shown in Figure 5-2. All port pins, except RB3/GP3 which is input only, may be used for both input and output operations. For input operations, these ports are non-latching. Any input must be present until read by an input instruction (e.g., MOVF PORTB, W). The outputs are latched and remain unchanged until the output latch is rewritten. To use a port pin as output, the corresponding direction control bit in TRIS must be cleared (= 0). For use as an input, the corresponding TRIS bit must be set. Any I/O pin (except RB3/GP3) can be programmed individually as input or output. FIGURE 5-1: PIC12F508/509/16F505 EQUIVALENT CIRCUIT FOR A SINGLE I/O PIN Data Bus D WR Port W Reg Q Data Latch CK VDD VDD Q P N D PORTC (PIC16F505 Only) PORTC is an 8-bit I/O register. Only the low-order 6 bits are used (RC<5:0>). Bits 7 and 6 are unimplemented and read as ‘0’s. Note: I/O Interfacing PORTB/GPIO PORTB/GPIO is an 8-bit I/O register. Only the loworder 6 bits are used (RB/GP<5:0>). Bits 7 and 6 are unimplemented and read as ‘0’s. Please note that RB3/ GP3 is an input only pin. The Configuration Word can set several I/O’s to alternate functions. When acting as alternate functions, the pins will read as ‘0’ during a port read. Pins RB0/GP0, RB1/GP1, RB3/GP3 and RB4 can be configured with weak pull-ups and also for wake-up on change. The wake-up on change and weak pull-up functions are not pin selectable. If RB3/GP3/ MCLR is configured as MCLR, weak pull-up is always on and wake-up on change for this pin is not enabled. 5.2 5.4 TRIS ‘f’ Q TRIS Latch CK VSS VSS Q Reset On power-up, TOCKI functionality is enabled in the OPTION register and must be disabled to allow RC5 to be used as general purpose I/O. I/O pin (1) RD Port 5.3 TRIS Registers Note 1: See Table 3-3 for buffer type. The Output Driver Control register is loaded with the contents of the W register by executing the TRIS f instruction. A ‘1’ from a TRIS register bit puts the corresponding output driver in a High-Impedance mode. A ‘0’ puts the contents of the output data latch on the selected pins, enabling the output buffer. The exceptions are RB3/GP3, which is input only and the T0CKI pin, which may be controlled by the OPTION register. See Register 4-3 and Register 4-4. Note: A read of the ports reads the pins, not the output data latches. That is, if an output driver on a pin is enabled and driven high, but the external system is holding it low, a read of the port will indicate that the pin is low. The TRIS registers are “write-only” and are set (output drivers disabled) upon Reset. © 2009 Microchip Technology Inc. DS41236E-page 31 PIC12F508/509/16F505 TABLE 5-1: Address SUMMARY OF PORT REGISTERS Name Bit 7 Bit 6 TRISGPIO(1) Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on Power-On Reset Value on All Other Resets — — I/O Control Register --11 1111 --11 1111 N/A (2) TRISB — — I/O Control Register --11 1111 --11 1111 N/A TRISC(2) — — I/O Control Register --11 1111 --11 1111 N/A OPTION(1) GPWU GPPU TOCS TOSE PSA PS2 PS1 PS0 1111 1111 1111 1111 N/A OPTION(2) RBWU RBPU TOCS TOSE PSA PS2 PS1 PS0 1111 1111 1111 1111 03h STATUS (1) GPWUF — PAO TO PD Z DC C 0-01 1xxx q00q quuu(3) 03h STATUS(2) RBWUF — PAO TO PD Z DC C 0-01 1xxx q00q quuu(3) N/A (1) 06h GPIO — — GP5 GP4 GP3 GP2 GP1 GP0 --xx xxxx --uu uuuu 06h PORTB(2) — — RB5 RB4 RB3 RB2 RB1 RB0 --xx xxxx --uu uuuu 07h PORTC(2) — — RC5 RC4 RC3 RC2 RC1 RC0 --xx xxxx --uu uuuu Legend: Note 1: 2: 3: Shaded cells are not used by Port registers, read as ‘0’. – = unimplemented, read as ‘0’, x = unknown, u = unchanged, q = depends on condition. PIC12F508/509 only. PIC16F505 only. If Reset was due to wake-up on pin change, then bit 7 = 1. All other Resets will cause bit 7 = 0. DS41236E-page 32 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 5.5 I/O Programming Considerations 5.5.1 BIDIRECTIONAL I/O PORTS Some instructions operate internally as read followed by write operations. The BCF and BSF instructions, for example, read the entire port into the CPU, execute the bit operation and re-write the result. Caution must be used when these instructions are applied to a port where one or more pins are used as input/outputs. For example, a BSF operation on bit 5 of PORTB/GPIO will cause all eight bits of PORTB/GPIO to be read into the CPU, bit 5 to be set and the PORTB/GPIO value to be written to the output latches. If another bit of PORTB/ GPIO is used as a bidirectional I/O pin (say bit 0) and it is defined as an input at this time, the input signal present on the pin itself would be read into the CPU and rewritten to the data latch of this particular pin, overwriting the previous content. As long as the pin stays in the Input mode, no problem occurs. However, if bit 0 is switched into Output mode later on, the content of the data latch may now be unknown. Example 5-1 shows the effect of two sequential Read-Modify-Write instructions (e.g., BCF, BSF, etc.) on an I/O port. A pin actively outputting a high or a low should not be driven from external devices at the same time in order to change the level on this pin (“wired OR”, “wired AND”). The resulting high output currents may damage the chip. FIGURE 5-2: READ-MODIFY-WRITE INSTRUCTIONS ON AN I/O PORT(e.g., PIC16F505) ;Initial PORTB Settings ;PORTB<5:3> Inputs ;PORTB<2:0> Outputs ; ; PORTB latch PORTB pins ; ------------------BCF PORTB, 5 ;--01 -ppp --11 pppp BCF PORTB, 4 ;--10 -ppp --11 pppp MOVLW 007h; TRIS PORTB ;--10 -ppp --11 pppp ; Note 1: The user may have expected the pin values to be ‘--00 pppp’. The 2nd BCF caused RB5 to be latched as the pin value (High). 5.5.2 SUCCESSIVE OPERATIONS ON I/O PORTS The actual write to an I/O port happens at the end of an instruction cycle, whereas for reading, the data must be valid at the beginning of the instruction cycle (Figure 5-2). Therefore, care must be exercised if a write followed by a read operation is carried out on the same I/O port. The sequence of instructions should allow the pin voltage to stabilize (load dependent) before the next instruction causes that file to be read into the CPU. Otherwise, the previous state of that pin may be read into the CPU rather than the new state. When in doubt, it is better to separate these instructions with a NOP or another instruction not accessing this I/O port. SUCCESSIVE I/O OPERATION (PIC16F505 Shown) Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 PC Instruction Fetched EXAMPLE 5-1: MOVWF PORTB PC + 1 MOVF PORTB, W Q1 Q2 Q3 Q4 PC + 2 PC + 3 This example shows a write to PORTB followed by a read from PORTB. NOP NOP Data setup time = (0.25 TCY – TPD) where: TCY = instruction cycle RB<5:0> TPD = propagation delay Port pin written here Instruction Executed MOVWF PORTB (Write to PORTB) © 2009 Microchip Technology Inc. Port pin sampled here MOVF PORTB,W (Read PORTB) Therefore, at higher clock frequencies, a write followed by a read may be problematic. NOP DS41236E-page 33 PIC12F508/509/16F505 NOTES: DS41236E-page 34 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 6.0 TIMER0 MODULE AND TMR0 REGISTER Counter mode is selected by setting the T0CS bit (OPTION<5>). In this mode, Timer0 will increment either on every rising or falling edge of pin T0CKI. The T0SE bit (OPTION<4>) determines the source edge. Clearing the T0SE bit selects the rising edge. Restrictions on the external clock input are discussed in detail in Section 6.1 “Using Timer0 with an External Clock”. The Timer0 module has the following features: • • • • 8-bit timer/counter register, TMR0 Readable and writable 8-bit software programmable prescaler Internal or external clock select: - Edge select for external clock Figure 6-1 is a simplified block diagram of the Timer0 module. Timer mode is selected by clearing the T0CS bit (OPTION<5>). In Timer mode, the Timer0 module will increment every instruction cycle (without prescaler). If TMR0 register is written, the increment is inhibited for the following two cycles (Figure 6-2 and Figure 6-3). The user can work around this by writing an adjusted value to the TMR0 register. FIGURE 6-1: The prescaler may be used by either the Timer0 module or the Watchdog Timer, but not both. The prescaler assignment is controlled in software by the control bit, PSA (OPTION<3>). Clearing the PSA bit will assign the prescaler to Timer0. The prescaler is not readable or writable. When the prescaler is assigned to the Timer0 module, prescale values of 1:2, 1:4,..., 1:256 are selectable. Section 6.2 “Prescaler” details the operation of the prescaler. A summary of registers associated with the Timer0 module is found in Table 6-1. TIMER0 BLOCK DIAGRAM Data Bus (GP2/RC5)/T0CKI FOSC/4 Pin 0 PSOUT 1 1 Programmable Prescaler(2) 0 T0SE 8 Sync with Internal Clocks TMR0 Reg PSOUT (2 TCY delay) Sync 3 T0CS(1) Note 1: 2: The prescaler is shared with the Watchdog Timer (Figure 6-5). TIMER0 TIMING: INTERNAL CLOCK/NO PRESCALE Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 PC – 1 Instruction Fetch Timer0 PSA(1) Bits T0CS, T0SE, PSA, PS2, PS1 and PS0 are located in the OPTION register. FIGURE 6-2: PC (Program Counter) PS2, PS1, PS0(1) PC MOVWF TMR0 T0 T0 + 1 Instruction Executed © 2009 Microchip Technology Inc. PC + 1 PC + 2 PC + 3 PC + 4 PC + 5 PC + 6 MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W T0 + 2 Write TMR0 executed NT0 + 1 NT0 Read TMR0 reads NT0 Read TMR0 reads NT0 Read TMR0 reads NT0 NT0 + 2 Read TMR0 Read TMR0 reads NT0 + 1 reads NT0 + 2 DS41236E-page 35 PIC12F508/509/16F505 FIGURE 6-3: TIMER0 TIMING: INTERNAL CLOCK/PRESCALE 1:2 PC Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 (Program PC – 1 PC PC + 1 PC + 2 PC + 3 PC + 4 PC + 5 PC + 6 Counter) Instruction Fetch MOVWF TMR0 T0 Timer0 T0 + 1 Instruction Executed 01h NT0 Write TMR0 executed TABLE 6-1: Address MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W Read TMR0 reads NT0 Read TMR0 Read TMR0 reads NT0 + 1 reads NT0 + 2 Read TMR0 reads NT0 REGISTERS ASSOCIATED WITH TIMER0 Name TMR0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 OPTION GPWU GPPU N/A OPTION (2) RBWU RBPU N/A TRISGPIO(1), (3) — — — — (2), (3) T0CS T0SE PSA PS2 PS1 PS0 T0CS T0SE PSA PS2 PS1 PS0 I/O Control Register RC4 RC3 RC2 RC1 Value on All Other Resets xxxx xxxx uuuu uuuu 1111 1111 1111 1111 RC0 1111 1111 1111 1111 --11 1111 --11 1111 --11 1111 --11 1111 N/A TRISC Legend: Note 1: 2: 3: Shaded cells are not used by Timer0. – = unimplemented, x = unknown, u = unchanged. PIC12F508/509 only. PIC16F505 only. The TRIS of the T0CKI pin is overridden when T0CS = 1. DS41236E-page 36 RC5 Value on Power-On Reset Bit 0 Timer0 – 8-bit Real-Time Clock/Counter (1) N/A Read TMR0 reads NT0 NT0 + 1 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 6.1 Using Timer0 with an External Clock When an external clock input is used for Timer0, it must meet certain requirements. The external clock requirement is due to internal phase clock (TOSC) synchronization. Also, there is a delay in the actual incrementing of Timer0 after synchronization. 6.1.1 EXTERNAL CLOCK SYNCHRONIZATION When no prescaler is used, the external clock input is the same as the prescaler output. The synchronization of T0CKI with the internal phase clocks is accomplished by sampling the prescaler output on the Q2 and Q4 cycles of the internal phase clocks (Figure 6-4). Therefore, it is necessary for T0CKI to be high for at least 2 TOSC (and a small RC delay of 2 Tt0H) and low for at least 2 TOSC (and a small RC delay of 2 Tt0H). Refer to the electrical specification of the desired device. FIGURE 6-4: When a prescaler is used, the external clock input is divided by the asynchronous ripple counter-type prescaler, so that the prescaler output is symmetrical. For the external clock to meet the sampling requirement, the ripple counter must be taken into account. Therefore, it is necessary for T0CKI to have a period of at least 4 TOSC (and a small RC delay of 4 Tt0H) divided by the prescaler value. The only requirement on T0CKI high and low time is that they do not violate the minimum pulse width requirement of Tt0H. Refer to parameters 40, 41 and 42 in the electrical specification of the desired device. 6.1.2 TIMER0 INCREMENT DELAY Since the prescaler output is synchronized with the internal clocks, there is a small delay from the time the external clock edge occurs to the time the Timer0 module is actually incremented. Figure 6-4 shows the delay from the external clock edge to the timer incrementing. TIMER0 TIMING WITH EXTERNAL CLOCK Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 External Clock Input or Prescaler Output (2) Q1 Q2 Q3 Q4 Small pulse misses sampling (1) External Clock/Prescaler Output After Sampling (3) Increment Timer0 (Q4) Timer0 Note 1: T0 T0 + 1 T0 + 2 Delay from clock input change to Timer0 increment is 3 TOSC to 7 TOSC. (Duration of Q = TOSC). Therefore, the error in measuring the interval between two edges on Timer0 input = ±4 TOSC max. 2: External clock if no prescaler selected; prescaler output otherwise. 3: The arrows indicate the points in time where sampling occurs. © 2009 Microchip Technology Inc. DS41236E-page 37 PIC12F508/509/16F505 6.2 Prescaler An 8-bit counter is available as a prescaler for the Timer0 module or as a postscaler for the Watchdog Timer (WDT), respectively (see Section 7.6 “Watchdog Timer (WDT)”). For simplicity, this counter is being referred to as “prescaler” throughout this data sheet. Note: The prescaler may be used by either the Timer0 module or the WDT, but not both. Thus, a prescaler assignment for the Timer0 module means that there is no prescaler for the WDT and vice versa. The PSA and PS<2:0> bits (OPTION<3:0>) determine prescaler assignment and prescale ratio. When assigned to the Timer0 module, all instructions writing to the TMR0 register (e.g., CLRF 1, MOVWF 1, BSF 1, x, etc.) will clear the prescaler. When assigned to WDT, a CLRWDT instruction will clear the prescaler along with the WDT. The prescaler is neither readable nor writable. On a Reset, the prescaler contains all ‘0’s. 6.2.1 SWITCHING PRESCALER ASSIGNMENT EXAMPLE 6-1: CHANGING PRESCALER (TIMER0 → WDT) CLRWDT ;Clear WDT CLRF TMR0 ;Clear TMR0 & Prescaler MOVLW ‘00xx1111’b ;These 3 lines (5, 6, 7) OPTION ;are required only if ;desired CLRWDT ;PS<2:0> are 000 or 001 MOVLW ‘00xx1xxx’b ;Set Postscaler to OPTION ;desired WDT rate To change the prescaler from the WDT to the Timer0 module, use the sequence shown in Example 6-2. This sequence must be used even if the WDT is disabled. A CLRWDT instruction should be executed before switching the prescaler. EXAMPLE 6-2: CLRWDT MOVLW ‘xxxx0xxx’ CHANGING PRESCALER (WDT → TIMER0) ;Clear WDT and ;prescaler ;Select TMR0, new ;prescale value and ;clock source OPTION The prescaler assignment is fully under software control (i.e., it can be changed “on-the-fly” during program execution). To avoid an unintended device Reset, the following instruction sequence (Example 6-1) must be executed when changing the prescaler assignment from Timer0 to the WDT. DS41236E-page 38 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 BLOCK DIAGRAM OF THE TIMER0/WDT PRESCALER(1), (2) FIGURE 6-5: TCY (= FOSC/4) Data Bus 0 (GP2/RC5)/T0CKI pin 1 8 M U X 1 M U X 0 T0SE T0CS 0 Watchdog Timer 1 M U X Sync 2 Cycles TMR0 Reg PSA 8-bit Prescaler 8 8-to-1 MUX PS<2:0> PSA WDT Enable bit 1 0 MUX PSA WDT Time-out Note 1: 2: T0CS, T0SE, PSA, PS<2:0> are bits in the OPTION register. T0CKI is shared with pin RC5 on the PIC16F505 and pin GP2 on the PIC12F508/509. © 2009 Microchip Technology Inc. DS41236E-page 39 PIC12F508/509/16F505 NOTES: DS41236E-page 40 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 7.0 SPECIAL FEATURES OF THE CPU What sets a microcontroller apart from other processors are special circuits that deal with the needs of real-time applications. The PIC12F508/509/16F505 microcontrollers have a host of such features intended to maximize system reliability, minimize cost through elimination of external components, provide powersaving operating modes and offer code protection. These features are: • Oscillator Selection • Reset: - Power-on Reset (POR) - Device Reset Timer (DRT) - Wake-up from Sleep on Pin Change • Watchdog Timer (WDT) • Sleep • Code Protection • ID Locations • In-Circuit Serial Programming™ • Clock Out © 2009 Microchip Technology Inc. The PIC12F508/509/16F505 devices have a Watchdog Timer, which can be shut off only through Configuration bit WDTE. It runs off of its own RC oscillator for added reliability. If using HS (PIC16F505), XT or LP selectable oscillator options, there is always an 18 ms (nominal) delay provided by the Device Reset Timer (DRT), intended to keep the chip in Reset until the crystal oscillator is stable. If using INTRC or EXTRC, there is an 18 ms delay only on VDD power-up. With this timer on-chip, most applications need no external Reset circuitry. The Sleep mode is designed to offer a very low-current Power-Down mode. The user can wake-up from Sleep through a change on input pins or through a Watchdog Timer time-out. Several oscillator options are also made available to allow the part to fit the application, including an internal 4 MHz oscillator. The EXTRC oscillator option saves system cost while the LP crystal option saves power. A set of Configuration bits are used to select various options. 7.1 Configuration Bits The PIC12F508/509/16F505 Configuration Words consist of 12 bits. Configuration bits can be programmed to select various device configurations. Three bits are for the selection of the oscillator type; (two bits on the PIC12F508/509), one bit is the Watchdog Timer enable bit, one bit is the MCLR enable bit and one bit is for code protection (Register 7-1, Register 7-2). DS41236E-page 41 PIC12F508/509/16F505 REGISTER 7-1: — — CONFIGURATION WORD FOR PIC12F508/509(1) — — — — — MCLRE CP WDTE FOSC1 bit 11 FOSC0 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 11-5 Unimplemented: Read as ‘0’ bit 4 MCLRE: GP3/MCLR Pin Function Select bit 1 = GP3/MCLR pin function is MCLR 0 = GP3/MCLR pin function is digital input, MCLR internally tied to VDD bit 3 CP: Code Protection bit 1 = Code protection off 0 = Code protection on bit 2 WDTE: Watchdog Timer Enable bit 1 = WDT enabled 0 = WDT disabled bit 1-0 FOSC<1:0>: Oscillator Selection bits 11 = EXTRC = external RC oscillator 10 = INTRC = internal RC oscillator 01 = XT oscillator 00 = LP oscillator Note 1: x = Bit is unknown Refer to the “PIC12F508/509 Memory Programming Specifications” (DS41227) to determine how to access the Configuration Word. The Configuration Word is not user addressable during device operation. DS41236E-page 42 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 REGISTER 7-2: — — CONFIGURATION WORD FOR PIC16F505(1) — — — — MCLRE CP WDTE FOSC2 FOSC1 bit 11 FOSC0 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 11-6 Unimplemented: Read as ‘0’ bit 5 MCLRE: RB3/MCLR Pin Function Select bit 1 = RB3/MCLR pin function is MCLR 0 = RB3/MCLR pin function is digital input, MCLR internally tied to VDD bit 4 CP: Code Protection bit 1 = Code protection off 0 = Code protection on bit 3 WDTE: Watchdog Timer Enable bit 1 = WDT enabled 0 = WDT disabled bit 2-0 FOSC<1:0>: Oscillator Selection bits 111 = External RC oscillator/CLKOUT function on RB4/OSC2/CLKOUT pin 110 = External RC oscillator/RB4 function on RB4/OSC2/CLKOUT pin 101 = Internal RC oscillator/CLKOUT function on RB4/OSC2/CLKOUT pin 100 = Internal RC oscillator/RB4 function on RB4/OSC2/CLKOUT pin 011 = EC oscillator/RB4 function on RB4/OSC2/CLKOUT pin 010 = HS oscillator 001 = XT oscillator 000 = LP oscillator Note 1: x = Bit is unknown Refer to the “PIC16F505 Memory Programming Specifications” (DS41226) to determine how to access the Configuration Word. The Configuration Word is not user addressable during device operation. © 2009 Microchip Technology Inc. DS41236E-page 43 PIC12F508/509/16F505 7.2 7.2.1 Oscillator Configurations FIGURE 7-1: OSCILLATOR TYPES The PIC12F508/509/16F505 devices can be operated in up to six different oscillator modes. The user can program up to three Configuration bits (FOSC<1:0> [PIC12F508/509], FOSC<2:0> [PIC16F505]). To select one of these modes: Low-Power Crystal Crystal/Resonator High-Speed Crystal/Resonator (PIC16F505 only) • INTRC: Internal 4 MHz Oscillator • EXTRC: External Resistor/Capacitor • EC: External High-Speed Clock Input (PIC16F505 only) C1(1) Sleep XTAL RS Note 1: This device has been designed to perform to the parameters of its data sheet. It has been tested to an electrical specification designed to determine its conformance with these parameters. Due to process differences in the manufacture of this device, this device may have different performance characteristics than its earlier version. These differences may cause this device to perform differently in your application than the earlier version of this device. 2: The user should verify that the device oscillator starts and performs as expected. Adjusting the loading capacitor values and/or the Oscillator mode may be required. DS41236E-page 44 (2) RF(3) OSC2 To internal logic C2(1) Note 1: See Capacitor Selection tables for recommended values of C1 and C2. A series resistor (RS) may be required for AT strip cut crystals. RF approx. value = 10 MΩ. 2: 3: CRYSTAL OSCILLATOR/CERAMIC RESONATORS In HS (PIC16F505), XT or LP modes, a crystal or ceramic resonator is connected to the (GP5/RB5)/ OSC1/(CLKIN) and (GP4/RB4)/OSC2/(CLKOUT) pins to establish oscillation (Figure 7-1). The PIC12F508/ 509/16F505 oscillator designs require the use of a parallel cut crystal. Use of a series cut crystal may give a frequency out of the crystal manufacturers specifications. When in HS (PIC16F505), XT or LP modes, the device can have an external clock source drive the (GP5/RB5)/OSC1/CLKIN pin (Figure 7-2). When the part is used in this fashion, the output drive levels on the OSC2 pin are very weak. This pin should be left open and unloaded. Also, when using this mode, the external clock should observe the frequency limits for the clock mode chosen (HS, XT or LP). PIC12F508/509 PIC16F505 OSC1 • LP: • XT: • HS: 7.2.2 CRYSTAL OPERATION (OR CERAMIC RESONATOR) (HS, XT OR LP OSC CONFIGURATION) FIGURE 7-2: EXTERNAL CLOCK INPUT OPERATION (HS, XT OR LP OSC CONFIGURATION) OSC1 Clock from ext. system PIC12F508/509 PIC16F505 Open TABLE 7-1: OSC2 CAPACITOR SELECTION FOR CERAMIC RESONATORS – PIC12F508/509/16F505(1) Osc Type Resonator Freq. Cap. Range C1 Cap. Range C2 XT 4.0 MHz 30 pF 30 pF 16 MHz 10-47 pF 10-47 pF HS(2) Note 1: 2: These values are for design guidance only. Since each resonator has its own characteristics, the user should consult the resonator manufacturer for appropriate values of external components. PIC16F505 only. © 2009 Microchip Technology Inc. PIC12F508/509/16F505 TABLE 7-2: CAPACITOR SELECTION FOR CRYSTAL OSCILLATOR – PIC12F508/509/16F505(2) Osc Type Resonator Freq. Cap. Range C1 Cap. Range C2 LP 32 kHz(1) 15 pF 15 pF XT 200 kHz 1 MHz 4 MHz 47-68 pF 15 pF 15 pF 47-68 pF 15 pF 15 pF 20 MHz 15-47 pF 15-47 pF HS(3) Note 1: 2: 3: 7.2.3 FIGURE 7-3: EXTERNAL PARALLEL RESONANT CRYSTAL OSCILLATOR CIRCUIT +5V To Other Devices 10k For VDD > 4.5V, C1 = C2 ≈ 30 pF is recommended. These values are for design guidance only. Rs may be required to avoid overdriving crystals with low drive level specification. Since each crystal has its own characteristics, the user should consult the crystal manufacturer for appropriate values of external components. PIC16F505 only. EXTERNAL CRYSTAL OSCILLATOR CIRCUIT Either a prepackaged oscillator or a simple oscillator circuit with TTL gates can be used as an external crystal oscillator circuit. Prepackaged oscillators provide a wide operating range and better stability. A well-designed crystal oscillator will provide good performance with TTL gates. Two types of crystal oscillator circuits can be used: one with parallel resonance, or one with series resonance. Figure 7-3 shows implementation of a parallel resonant oscillator circuit. The circuit is designed to use the fundamental frequency of the crystal. The 74AS04 inverter performs the 180-degree phase shift that a parallel oscillator requires. The 4.7 kΩ resistor provides the negative feedback for stability. The 10 kΩ potentiometers bias the 74AS04 in the linear region. This circuit could be used for external oscillator designs. 74AS04 4.7k CLKIN 74AS04 PIC16F505 PIC12F508 PIC12F509 10k XTAL 10k 20 pF 20 pF Figure 7-4 shows a series resonant oscillator circuit. This circuit is also designed to use the fundamental frequency of the crystal. The inverter performs a 180degree phase shift in a series resonant oscillator circuit. The 330 Ω resistors provide the negative feedback to bias the inverters in their linear region. FIGURE 7-4: 330 EXTERNAL SERIES RESONANT CRYSTAL OSCILLATOR CIRCUIT To Other Devices 330 74AS04 74AS04 74AS04 CLKIN 0.1 mF XTAL 7.2.4 PIC16F505 PIC12F508 PIC12F509 EXTERNAL RC OSCILLATOR For timing insensitive applications, the RC device option offers additional cost savings. The RC oscillator frequency is a function of the supply voltage, the resistor (REXT) and capacitor (CEXT) values, and the operating temperature. In addition to this, the oscillator frequency will vary from unit-to-unit due to normal process parameter variation. Furthermore, the difference in lead frame capacitance between package types will also affect the oscillation frequency, especially for low CEXT values. The user also needs to take into account variation due to tolerance of external R and C components used. Figure 7-5 shows how the R/C combination is connected to the PIC12F508/509/16F505 devices. For REXT values below 3.0 kΩ, the oscillator operation may become unstable, or stop completely. For very high REXT values (e.g., 1 MΩ), the oscillator becomes sensitive to noise, humidity and leakage. Thus, we recommend keeping REXT between 5.0 kΩ and 100 kΩ. © 2009 Microchip Technology Inc. DS41236E-page 45 PIC12F508/509/16F505 Although the oscillator will operate with no external capacitor (CEXT = 0 pF), we recommend using values above 20 pF for noise and stability reasons. With no or small external capacitance, the oscillation frequency can vary dramatically due to changes in external capacitances, such as PCB trace capacitance or package lead frame capacitance. Section 10.0 “Electrical Characteristics” shows RC frequency variation from part-to-part due to normal process variation. The variation is larger for larger values of R (since leakage current variation will affect RC frequency more for large R) and for smaller values of C (since variation of input capacitance will affect RC frequency more). Also, see the Electrical Specifications section for variation of oscillator frequency due to VDD for given REXT/CEXT values, as well as frequency variation due to operating temperature for given R, C and VDD values. FIGURE 7-5: EXTERNAL RC OSCILLATOR MODE VDD REXT OSC1 N CEXT PIC16F505 PIC12F508 PIC12F509 VSS FOSC/4 7.2.5 Internal clock In addition, a calibration instruction is programmed into the last address of memory, which contains the calibration value for the internal RC oscillator. This location is always uncode protected, regardless of the code-protect settings. This value is programmed as a MOVLW XX instruction where XX is the calibration value, and is placed at the Reset vector. This will load the W register with the calibration value upon Reset and the PC will then roll over to the users program at address 0x000. The user then has the option of writing the value to the OSCCAL Register (05h) or ignoring it. OSCCAL, when written to with the calibration value, will “trim” the internal oscillator to remove process variation from the oscillator frequency. Note: Erasing the device will also erase the preprogrammed internal calibration value for the internal oscillator. The calibration value must be read prior to erasing the part so it can be reprogrammed correctly later. For the PIC12F508/509/16F505 devices, only bits <7:1> of OSCCAL are implemented. Bits CAL6-CAL0 are used for calibration. Adjusting CAL6-CAL0 from ‘0000000’ to ‘1111111’ changes the clock speed. See Register 4-5 for more information. Note: The 0 bit of OSCCAL is unimplemented and should be written as ‘0’ when modifying OSCCAL for compatibility with future devices. OSC2/CLKOUT INTERNAL 4 MHz RC OSCILLATOR The internal RC oscillator provides a fixed 4 MHz (nominal) system clock at VDD = 5V and 25°C, (see Section 10.0 “Electrical Characteristics” for information on variation over voltage and temperature). DS41236E-page 46 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 7.3 Reset The device differentiates between various kinds of Reset: • • • • • • Power-on Reset (POR) MCLR Reset during normal operation MCLR Reset during Sleep WDT time-out Reset during normal operation WDT time-out Reset during Sleep Wake-up from Sleep on pin change TABLE 7-3: Register Some registers are not reset in any way, they are unknown on POR and unchanged in any other Reset. Most other registers are reset to “Reset state” on Power-on Reset (POR), MCLR, WDT or Wake-up on pin change Reset during normal operation. They are not affected by a WDT Reset during Sleep or MCLR Reset during Sleep, since these Resets are viewed as resumption of normal operation. The exceptions to this are TO, PD and RBWUF/GPWUF bits. They are set or cleared differently in different Reset situations. These bits are used in software to determine the nature of Reset. See Table 7-4 for a full description of Reset states of all registers. RESET CONDITIONS FOR REGISTERS – PIC12F508/509 Address W — Power-on Reset MCLR Reset, WDT Time-out, Wake-up On Pin Change qqqq qqqu(1) qqqq qqqu(1) INDF 00h xxxx xxxx uuuu uuuu TMR0 01h xxxx xxxx uuuu uuuu PC 02h 1111 1111 1111 1111 STATUS 03h 0001 1xxx q00q quuu(2), (3) FSR(4) 04h 110x xxxx 11uu uuuu FSR(5) 04h 111x xxxx 111u uuuu OSCCAL 05h 1111 111- uuuu uuu- GPIO 06h --xx xxxx --uu uuuu OPTION — 1111 1111 1111 1111 TRIS — --11 1111 --11 1111 Legend: u = unchanged, x = unknown, – = unimplemented bit, read as ‘0’, q = value depends on condition. Note 1: Bits <7:2> of W register contain oscillator calibration values due to MOVLW XX instruction at top of memory. 2: See Table 7-5 for Reset value for specific conditions. 3: If Reset was due to wake-up on pin change, then bit 7 = 1. All other Resets will cause bit 7 = 0. 4: PIC12F509 only. 5: PIC12F508 only. © 2009 Microchip Technology Inc. DS41236E-page 47 PIC12F508/509/16F505 TABLE 7-4: RESET CONDITIONS FOR REGISTERS – PIC16F505 Register Address W — Power-on Reset MCLR Reset, WDT Time-out, Wake-up On Pin Change qqqq qqqu(1) qqqq qqqu(1) INDF 00h xxxx xxxx uuuu uuuu TMR0 01h xxxx xxxx uuuu uuuu PC 02h 1111 1111 1111 1111 STATUS 03h 0001 1xxx q00q quuu(2), (3) FSR 04h 100x xxxx 1uuu uuuu OSCCAL 05h 1111 111- uuuu uuu- PORTB 06h --xx xxxx --uu uuuu PORTC 07h --xx xxxx --uu uuuu OPTION — 1111 1111 1111 1111 TRISB — --11 1111 --11 1111 TRISC — --11 1111 --11 1111 Legend: u = unchanged, x = unknown, – = unimplemented bit, read as ‘0’, q = value depends on condition. Note 1: Bits <7:2> of W register contain oscillator calibration values due to MOVLW XX instruction at top of memory. 2: See Table 7-5 for Reset value for specific conditions. 3: If Reset was due to wake-up on pin change, then bit 7 = 1. All other Resets will cause bit 7 = 0. TABLE 7-5: RESET CONDITION FOR SPECIAL REGISTERS STATUS Addr: 03h PCL Addr: 02h Power-on Reset 0001 1xxx 1111 1111 MCLR Reset during normal operation 000u uuuu 1111 1111 MCLR Reset during Sleep 0001 0uuu 1111 1111 WDT Reset during Sleep 0000 0uuu 1111 1111 WDT Reset normal operation 0000 uuuu 1111 1111 Wake-up from Sleep on pin change 1001 0uuu 1111 1111 Legend: u = unchanged, x = unknown, – = unimplemented bit, read as ‘0’. DS41236E-page 48 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 7.3.1 MCLR ENABLE This Configuration bit, when unprogrammed (left in the ‘1’ state), enables the external MCLR function. When programmed, the MCLR function is tied to the internal VDD and the pin is assigned to be an input only. See Figure 7-6. FIGURE 7-6: MCLR SELECT GPWU/RBWU (GP3/RB3)/MCLR/VPP Internal MCLR MCLRE 7.4 Power-on Reset (POR) The PIC12F508/509/16F505 devices incorporate an on-chip Power-on Reset (POR) circuitry, which provides an internal chip Reset for most power-up situations. The on-chip POR circuit holds the chip in Reset until VDD has reached a high enough level for proper operation. To take advantage of the internal POR, program the (GP3/RB3)/MCLR/VPP pin as MCLR and tie through a resistor to VDD, or program the pin as (GP3/RB3). An internal weak pull-up resistor is implemented using a transistor (refer to Table 10-2 for the pull-up resistor ranges). This will eliminate external RC components usually needed to create a Power-on Reset. A maximum rise time for VDD is specified. See Section 10.0 “Electrical Characteristics” for details. The Power-on Reset circuit and the Device Reset Timer (see Section 7.5 “Device Reset Timer (DRT)”) circuit are closely related. On power-up, the Reset latch is set and the DRT is reset. The DRT timer begins counting once it detects MCLR to be high. After the time-out period, which is typically 18 ms, it will reset the Reset latch and thus end the on-chip Reset signal. A power-up example where MCLR is held low is shown in Figure 7-8. VDD is allowed to rise and stabilize before bringing MCLR high. The chip will actually come out of Reset TDRT msec after MCLR goes high. In Figure 7-9, the on-chip Power-on Reset feature is being used (MCLR and VDD are tied together or the pin is programmed to be (GP3/RB3). The VDD is stable before the start-up timer times out and there is no problem in getting a proper Reset. However, Figure 7-10 depicts a problem situation where VDD rises too slowly. The time between when the DRT senses that MCLR is high and when MCLR and VDD actually reach their full value, is too long. In this situation, when the start-up timer times out, VDD has not reached the VDD (min) value and the chip may not function correctly. For such situations, we recommend that external RC circuits be used to achieve longer POR delay times (Figure 7-9). Note: When the devices start normal operation (exit the Reset condition), device operating parameters (voltage, frequency, temperature, etc.) must be met to ensure operation. If these conditions are not met, the device must be held in Reset until the operating conditions are met. For additional information, refer to Application Notes AN522 “Power-Up Considerations” (DS00522) and AN607 “Power-up Trouble Shooting” (DS00607). When the devices start normal operation (exit the Reset condition), device operating parameters (voltage, frequency, temperature,...) must be met to ensure operation. If these conditions are not met, the devices must be held in Reset until the operating parameters are met. A simplified block diagram of the on-chip Power-on Reset circuit is shown in Figure 7-7. © 2009 Microchip Technology Inc. DS41236E-page 49 PIC12F508/509/16F505 FIGURE 7-7: SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT VDD Power-up Detect POR (Power-on Reset) (GP3/RB3)/MCLR/VPP MCLR Reset MCLRE WDT Reset WDT Time-out S Q R Q Start-up Timer CHIP Reset (10 μs or 18 ms) Pin Change Sleep Wake-up on pin Change Reset FIGURE 7-8: TIME-OUT SEQUENCE ON POWER-UP (MCLR PULLED LOW) VDD MCLR Internal POR TDRT DRT Time-out Internal Reset TIME-OUT SEQUENCE ON POWER-UP (MCLR TIED TO VDD): FAST VDD RISE TIME FIGURE 7-9: VDD MCLR Internal POR TDRT DRT Time-out Internal Reset DS41236E-page 50 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 FIGURE 7-10: TIME-OUT SEQUENCE ON POWER-UP (MCLR TIED TO VDD): SLOW VDD RISE TIME V1 VDD MCLR Internal POR TDRT DRT Time-out Internal Reset Note: When VDD rises slowly, the TDRT time-out expires long before VDD has reached its final value. In this example, the chip will reset properly if, and only if, V1 ≥ VDD min. © 2009 Microchip Technology Inc. DS41236E-page 51 PIC12F508/509/16F505 7.5 Device Reset Timer (DRT) On the PIC12F508/509/16F505 devices, the DRT runs any time the device is powered up. DRT runs from Reset and varies based on oscillator selection and Reset type (see Table 7-6). The DRT operates on an internal RC oscillator. The processor is kept in Reset as long as the DRT is active. The DRT delay allows VDD to rise above VDD min. and for the oscillator to stabilize. Oscillator circuits based on crystals or ceramic resonators require a certain time after power-up to establish a stable oscillation. The on-chip DRT keeps the devices in a Reset condition for approximately 18 ms after MCLR has reached a logic high (VIH MCLR) level. Programming (GP3/RB3)/MCLR/VPP as MCLR and using an external RC network connected to the MCLR input is not required in most cases. This allows savings in cost-sensitive and/or space restricted applications, as well as allowing the use of the (GP3/RB3)/MCLR/VPP pin as a general purpose input. The Device Reset Time delays will vary from chip-tochip due to VDD, temperature and process variation. See AC parameters for details. The DRT will also be triggered upon a Watchdog Timer time-out from Sleep. This is particularly important for applications using the WDT to wake from Sleep mode automatically. Reset sources are POR, MCLR, WDT time-out and wake-up on pin change. See Section 7.9.2 “Wake-up from Sleep”, Notes 1, 2 and 3. 7.6 TABLE 7-6: DRT (DEVICE RESET TIMER PERIOD) Oscillator Configuration POR Reset Subsequent Resets INTOSC, EXTRC 18 ms (typical) 10 μs (typical) HS(1) 18 ms (typical) 18 ms (typical) 18 ms (typical) 10 μs (typical) , XT, LP (1) EC Note 1: 7.6.1 PIC16F505 only. WDT PERIOD The WDT has a nominal time-out period of 18 ms, (with no prescaler). If a longer time-out period is desired, a prescaler with a division ratio of up to 1:128 can be assigned to the WDT (under software control) by writing to the OPTION register. Thus, a time-out period of a nominal 2.3 seconds can be realized. These periods vary with temperature, VDD and part-to-part process variations (see DC specs). Under worst case conditions (VDD = Min., Temperature = Max., max. WDT prescaler), it may take several seconds before a WDT time-out occurs. 7.6.2 WDT PROGRAMMING CONSIDERATIONS The CLRWDT instruction clears the WDT and the postscaler, if assigned to the WDT, and prevents it from timing out and generating a device Reset. The SLEEP instruction resets the WDT and the postscaler, if assigned to the WDT. This gives the maximum Sleep time before a WDT wake-up Reset. Watchdog Timer (WDT) The Watchdog Timer (WDT) is a free running on-chip RC oscillator, which does not require any external components. This RC oscillator is separate from the external RC oscillator of the (GP5/RB5)/OSC1/CLKIN pin and the internal 4 MHz oscillator. This means that the WDT will run even if the main processor clock has been stopped, for example, by execution of a SLEEP instruction. During normal operation or Sleep, a WDT Reset or wake-up Reset, generates a device Reset. The TO bit (STATUS<4>) will be cleared upon a Watchdog Timer Reset. The WDT can be permanently disabled by programming the configuration WDTE as a ‘0’ (see Section 7.1 “Configuration Bits”). Refer to the PIC12F508/509/16F505 Programming Specifications to determine how to access the Configuration Word. DS41236E-page 52 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 FIGURE 7-11: WATCHDOG TIMER BLOCK DIAGRAM From Timer0 Clock Source (Figure 6-5) 0 1 Watchdog Time M U X Postscaler 8-to-1 MUX PS<2:0> PSA WDT Enable Configuration Bit To Timer0 (Figure 6-4) 0 1 MUX PSA WDT Time-out Note 1: TABLE 7-7: Address T0CS, T0SE, PSA, PS<2:0> are bits in the OPTION register. SUMMARY OF REGISTERS ASSOCIATED WITH THE WATCHDOG TIMER Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on Power-On Reset Value on All Other Resets N/A OPTION(1) GPWU GPPU T0CS T0SE PSA PS2 PS1 PS0 1111 1111 1111 1111 N/A OPTION(2) RBPU T0CS T0SE PSA PS2 PS1 PS0 1111 1111 1111 1111 RBWU Legend: Shaded boxes = Not used by Watchdog Timer. – = unimplemented, read as ‘0’, u = unchanged. Note 1: PIC12F508/509 only. 2: PIC16F505 only. © 2009 Microchip Technology Inc. DS41236E-page 53 PIC12F508/509/16F505 7.7 Time-out Sequence, Power-down and Wake-up from Sleep Status Bits (TO, PD, GPWUF/RBWUF) FIGURE 7-13: VDD VDD The TO, PD and (GPWUF/RBWUF) bits in the STATUS register can be tested to determine if a Reset condition has been caused by a Power-up condition, a MCLR or Watchdog Timer (WDT) Reset. TABLE 7-8: TO PD 0 0 0 WDT wake-up from Sleep 0 0 u WDT time-out (not from Sleep) 0 1 0 MCLR wake-up from Sleep 0 1 1 Power-up 0 u u MCLR not during Sleep 1 1 0 Wake-up from Sleep on pin change Reset Caused By Legend: u = unchanged Note 1: The TO, PD and GPWUF/RBWUF bits maintain their status (u) until a Reset occurs. A low-pulse on the MCLR input does not change the TO, PD and GPWUF/RBWUF Status bits. 7.8 R1 Note 1: To reset PIC12F508/509/16F505 devices when a brown-out occurs, external brown-out protection circuits may be built, as shown in Figure 7-12 and Figure 7-13. FIGURE 7-12: 40k(1) This brown-out circuit is less expensive, although less accurate. Transistor Q1 turns off when VDD is below a certain level such that: R1 VDD • 2: = 0.7V R1 + R2 Pin must be confirmed as MCLR. FIGURE 7-14: BROWN-OUT PROTECTION CIRCUIT 3 VDD MCP809 VSS RST Reset on Brown-out A brown-out is a condition where device power (VDD) dips below its minimum value, but not to zero, and then recovers. The device should be reset in the event of a brown-out. PIC16F505 PIC12F508 Q1 MCLR(2) PIC12F509 R2 TO/PD/(GPWUF/RBWUF) STATUS AFTER RESET GPWUF/ RBWUF BROWN-OUT PROTECTION CIRCUIT 2 Bypass Capacitor VDD VDD MCLR PIC16F505 PIC12F508 PIC12F509 Note: This brown-out protection circuit employs Microchip Technology’s MCP809 microcontroller supervisor. There are 7 different trip point selections to accommodate 5V to 3V systems. BROWN-OUT PROTECTION CIRCUIT 1 VDD VDD 33k 10k Q1 MCLR PIC16F505 PIC12F508 (2) PIC12F509 40k(1) Note 1: 2: This circuit will activate Reset when VDD goes below Vz + 0.7V (where Vz = Zener voltage). Pin must be confirmed as MCLR. DS41236E-page 54 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 7.9 Power-down Mode (Sleep) A device may be powered down (Sleep) and later powered up (wake-up from Sleep). 7.9.1 SLEEP The Power-Down mode is entered by executing a SLEEP instruction. If enabled, the Watchdog Timer will be cleared but keeps running, the TO bit (STATUS<4>) is set, the PD bit (STATUS<3>) is cleared and the oscillator driver is turned off. The I/O ports maintain the status they had before the SLEEP instruction was executed (driving high, driving low or high-impedance). Note: A Reset generated by a WDT time-out does not drive the MCLR pin low. For lowest current consumption while powered down, the T0CKI input should be at VDD or VSS and the (GP3/RB3)/MCLR/VPP pin must be at a logic high level if MCLR is enabled. 7.9.2 WAKE-UP FROM SLEEP 7.10 Program Verification/Code Protection If the code protection bit has not been programmed, the on-chip program memory can be read out for verification purposes. The first 64 locations and the last location (OSCCAL) can be read, regardless of the code protection bit setting. The last memory location can be read regardless of the code protection bit setting on the PIC12F508/509/ 16F505 devices. 7.11 ID Locations Four memory locations are designated as ID locations where the user can store checksum or other code identification numbers. These locations are not accessible during normal execution, but are readable and writable during Program/Verify. Use only the lower 4 bits of the ID locations and always program the upper 8 bits as ‘0’s. The device can wake-up from Sleep through one of the following events: 7.12 1. The PIC12F508/509/16F505 microcontrollers can be serially programmed while in the end application circuit. This is simply done with two lines for clock and data, and three other lines for power, ground and the programming voltage. This allows customers to manufacture boards with unprogrammed devices and then program the microcontroller just before shipping the product. This also allows the most recent firmware, or a custom firmware, to be programmed. 2. 3. An external Reset input on (GP3/RB3)/MCLR/ VPP pin, when configured as MCLR. A Watchdog Timer time-out Reset (if WDT was enabled). A change on input pin GP0/RB0, GP1/RB1, GP3/RB3 or RB4 when wake-up on change is enabled. These events cause a device Reset. The TO, PD and GPWUF/RBWUF bits can be used to determine the cause of device Reset. The TO bit is cleared if a WDT time-out occurred (and caused wake-up). The PD bit, which is set on power-up, is cleared when SLEEP is invoked. The GPWUF/RBWUF bit indicates a change in state while in Sleep at pins GP0/RB0, GP1/RB1, GP3/RB3 or RB4 (since the last file or bit operation on GP/RB port). Note: Caution: Right before entering Sleep, read the input pins. When in Sleep, wakeup occurs when the values at the pins change from the state they were in at the last reading. If a wake-up on change occurs and the pins are not read before reentering Sleep, a wake-up will occur immediately even if no pins change while in Sleep mode. In-Circuit Serial Programming™ The devices are placed into a Program/Verify mode by holding the GP1/RB1 and GP0/RB0 pins low while raising the MCLR (VPP) pin from VIL to VIHH (see programming specification). GP1/RB1 becomes the programming clock and GP0/RB0 becomes the programming data. Both GP1/RB1 and GP0/RB0 are Schmitt Trigger inputs in this mode. After Reset, a 6-bit command is then supplied to the device. Depending on the command, 14 bits of program data are then supplied to or from the device, depending if the command was a Load or a Read. For complete details of serial programming, please refer to the PIC12F508/509/16F505 Programming Specifications. A typical In-Circuit Serial Programming connection is shown in Figure 7-15. The WDT is cleared when the device wakes from Sleep, regardless of the wake-up source. © 2009 Microchip Technology Inc. DS41236E-page 55 PIC12F508/509/16F505 FIGURE 7-15: External Connector Signals TYPICAL IN-CIRCUIT SERIAL PROGRAMMING CONNECTION To Normal Connections PIC16F505 PIC12F508 PIC12F509 +5V VDD 0V VSS VPP MCLR/VPP CLK GP1/RB1 Data I/O GP0/RB0 VDD To Normal Connections DS41236E-page 56 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 8.0 INSTRUCTION SET SUMMARY The PIC16 instruction set is highly orthogonal and is comprised of three basic categories. • Byte-oriented operations • Bit-oriented operations • Literal and control operations Each PIC16 instruction is a 12-bit word divided into an opcode, which specifies the instruction type, and one or more operands which further specify the operation of the instruction. The formats for each of the categories is presented in Figure 8-1, while the various opcode fields are summarized in Table 8-1. For byte-oriented instructions, ‘f’ represents a file register designator and ‘d’ represents a destination designator. The file register designator specifies which file register is to be used by the instruction. The destination designator specifies where the result of the operation is to be placed. If ‘d’ is ‘0’, the result is placed in the W register. If ‘d’ is ‘1’, the result is placed in the file register specified in the instruction. For bit-oriented instructions, ‘b’ represents a bit field designator which selects the number of the bit affected by the operation, while ‘f’ represents the number of the file in which the bit is located. For literal and control operations, ‘k’ represents an 8 or 9-bit constant or literal value. TABLE 8-1: Description Register file address (0x00 to 0x7F) W Working register (accumulator) b Bit address within an 8-bit file register k Literal field, constant data or label x Don’t care location (= 0 or 1) The assembler will generate code with x = 0. It is the recommended form of use for compatibility with all Microchip software tools. d Destination select; d = 0 (store result in W) d = 1 (store result in file register ‘f’) Default is d = 1 label Label name TOS Top-of-Stack PC WDT TO Power-down bit Byte-oriented file register operations 11 6 OPCODE 5 d 4 0 f (FILE #) d = 0 for destination W d = 1 for destination f f = 5-bit file register address Bit-oriented file register operations 11 OPCODE 8 7 5 4 b (BIT #) 0 f (FILE #) b = 3-bit bit address f = 5-bit file register address Literal and control operations (except GOTO) 11 8 7 OPCODE 0 k (literal) k = 8-bit immediate value Literal and control operations – GOTO instruction 11 9 8 OPCODE 0 k (literal) k = 9-bit immediate value Options ( ) Contents → Assigned to italics GENERAL FORMAT FOR INSTRUCTIONS Watchdog Timer counter Destination, either the W register or the specified register file location ∈ FIGURE 8-1: Time-out bit PD <> 0xhhh where ‘h’ signifies a hexadecimal digit. Program Counter dest [ ] Figure 8-1 shows the three general formats that the instructions can have. All examples in the figure use the following format to represent a hexadecimal number: OPCODE FIELD DESCRIPTIONS Field f All instructions are executed within a single instruction cycle, unless a conditional test is true or the program counter is changed as a result of an instruction. In this case, the execution takes two instruction cycles. One instruction cycle consists of four oscillator periods. Thus, for an oscillator frequency of 4 MHz, the normal instruction execution time is 1 μs. If a conditional test is true or the program counter is changed as a result of an instruction, the instruction execution time is 2 μs. Register bit field In the set of User defined term (font is courier) © 2009 Microchip Technology Inc. DS41236E-page 57 PIC12F508/509/16F505 TABLE 8-2: INSTRUCTION SET SUMMARY Mnemonic, Operands ADDWF ANDWF CLRF CLRW COMF DECF DECFSZ INCF INCFSZ IORWF MOVF MOVWF NOP RLF RRF SUBWF SWAPF XORWF 12-Bit Opcode Description Cycles MSb LSb Status Notes Affected f, d f, d f — f, d f, d f, d f, d f, d f, d f, d f — f, d f, d f, d f, d f, d 0001 11df ffff C, DC, Z 1, 2, 4 Add W and f 1 0001 01df ffff AND W with f 1 Z 2, 4 0000 011f ffff Clear f 1 Z 4 0000 0100 0000 Clear W 1 Z 0010 01df ffff Complement f 1 Z 0000 11df ffff Decrement f 1 Z 2, 4 0010 11df ffff Decrement f, Skip if 0 1(2) None 2, 4 1 0010 10df ffff Increment f Z 2, 4 1(2) 0011 11df ffff Increment f, Skip if 0 None 2, 4 1 0001 00df ffff Inclusive OR W with f Z 2, 4 1 0010 00df ffff Move f Z 2, 4 1 0000 001f ffff Move W to f None 1, 4 1 0000 0000 0000 No Operation None 1 0011 01df ffff Rotate left f through Carry C 2, 4 1 0011 00df ffff Rotate right f through Carry C 2, 4 1 0000 10df ffff C, DC, Z 1, 2, 4 Subtract W from f 1 0011 10df ffff Swap f None 2, 4 1 0001 10df ffff Exclusive OR W with f Z 2, 4 BIT-ORIENTED FILE REGISTER OPERATIONS 0100 bbbf ffff None 2, 4 1 Bit Clear f BCF f, b 0101 bbbf ffff None 2, 4 1 Bit Set f BSF f, b 0110 bbbf ffff None Bit Test f, Skip if Clear 1(2) BTFSC f, b 1(2) 0111 bbbf ffff None f, b Bit Test f, Skip if Set BTFSS LITERAL AND CONTROL OPERATIONS ANDLW k AND literal with W 1 1110 kkkk kkkk Z CALL 1 k Call Subroutine 2 1001 kkkk kkkk None CLRWDT — Clear Watchdog Timer 1 0000 0000 0100 TO, PD None GOTO k Unconditional branch 2 101k kkkk kkkk Z IORLW k Inclusive OR literal with W 1 1101 kkkk kkkk None MOVLW k Move literal to W 1 1100 kkkk kkkk None OPTION — Load OPTION register 1 0000 0000 0010 None RETLW k Return, place literal in W 2 1000 kkkk kkkk SLEEP — Go into Standby mode 1 0000 0000 0011 TO, PD None 3 TRIS f Load TRIS register 1 0000 0000 0fff Z XORLW k Exclusive OR literal to W 1 1111 kkkk kkkk Note 1: The 9th bit of the program counter will be forced to a ‘0’ by any instruction that writes to the PC except for GOTO. See Section 4.7 “Program Counter”. 2: When an I/O register is modified as a function of itself (e.g. MOVF PORTB, 1), the value used will be that value present on the pins themselves. For example, if the data latch is ‘1’ for a pin configured as input and is driven low by an external device, the data will be written back with a ‘0’. 3: The instruction TRIS f, where f = 6, causes the contents of the W register to be written to the tri-state latches of PORTB. A ‘1’ forces the pin to a high-impedance state and disables the output buffers. 4: If this instruction is executed on the TMR0 register (and, where applicable, d = 1), the prescaler will be cleared (if assigned to TMR0). DS41236E-page 58 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 ADDWF Add W and f BCF Bit Clear f Syntax: [ label ] ADDWF Syntax: [ label ] BCF Operands: 0 ≤ f ≤ 31 d ∈ [0,1] Operands: 0 ≤ f ≤ 31 0≤b≤7 Operation: (W) + (f) → (dest) Operation: 0 → (f<b>) Status Affected: C, DC, Z Status Affected: None Description: Description: Bit ‘b’ in register ‘f’ is cleared. BSF Bit Set f ANDLW Syntax: f,d Add the contents of the W register and register ‘f’. If ‘d’ is’0’, the result is stored in the W register. If ‘d’ is ‘1’, the result is stored back in register ‘f’. AND literal with W [ label ] ANDLW k Syntax: [ label ] BSF Operands: 0 ≤ f ≤ 31 0≤b≤7 Status Affected: Z Operation: 1 → (f<b>) Description: The contents of the W register are AND’ed with the eight-bit literal ‘k’. The result is placed in the W register. Status Affected: None AND W with f BTFSC Operands: 0 ≤ k ≤ 255 Operation: (W).AND. (k) → (W) ANDWF f,b f,b Description: Bit ‘b’ in register ‘f’ is set. Bit Test f, Skip if Clear Syntax: [ label ] ANDWF Syntax: [ label ] BTFSC f,b Operands: 0 ≤ f ≤ 31 d ∈ [0,1] Operands: 0 ≤ f ≤ 31 0≤b≤7 Operation: (W) .AND. (f) → (dest) Operation: skip if (f<b>) = 0 Status Affected: Z Status Affected: None Description: Description: If bit ‘b’ in register ‘f’ is ‘0’, then the next instruction is skipped. If bit ‘b’ is ‘0’, then the next instruction fetched during the current instruction execution is discarded, and a NOP is executed instead, making this a two-cycle instruction. f,d The contents of the W register are AND’ed with register ‘f’. If ‘d’ is ‘0’, the result is stored in the W register. If ‘d’ is ‘1’, the result is stored back in register ‘f’. © 2009 Microchip Technology Inc. DS41236E-page 59 PIC12F508/509/16F505 BTFSS Bit Test f, Skip if Set CLRW Syntax: [ label ] BTFSS f,b Syntax: [ label ] CLRW 0 ≤ f ≤ 31 0≤b<7 Operands: None Operation: 00h → (W); 1→Z Operands: Clear W Operation: skip if (f<b>) = 1 Status Affected: None Status Affected: Z Description: If bit ‘b’ in register ‘f’ is ‘1’, then the next instruction is skipped. If bit ‘b’ is ‘1’, then the next instruction fetched during the current instruction execution, is discarded and a NOP is executed instead, making this a two-cycle instruction. Description: The W register is cleared. Zero bit (Z) is set. CALL Subroutine Call CLRWDT Clear Watchdog Timer Syntax: [ label ] CALL k Syntax: [ label ] CLRWDT Operands: 0 ≤ k ≤ 255 Operands: None Operation: (PC) + 1→ Top-of-Stack; k → PC<7:0>; (STATUS<6:5>) → PC<10:9>; 0 → PC<8> Operation: 00h → WDT; 0 → WDT prescaler (if assigned); 1 → TO; 1 → PD Status Affected: None Status Affected: TO, PD Description: Subroutine call. First, return address (PC + 1) is PUSHed onto the stack. The eight-bit immediate address is loaded into PC bits <7:0>. The upper bits PC<10:9> are loaded from STATUS<6:5>, PC<8> is cleared. CALL is a two-cycle instruction. Description: The CLRWDT instruction resets the WDT. It also resets the prescaler, if the prescaler is assigned to the WDT and not Timer0. Status bits TO and PD are set. CLRF Clear f COMF Complement f Syntax: [ label ] CLRF Syntax: [ label ] COMF Operands: 0 ≤ f ≤ 31 Operands: Operation: 00h → (f); 1→Z 0 ≤ f ≤ 31 d ∈ [0,1] Operation: (f) → (dest) Z Status Affected: Z The contents of register ‘f’ are cleared and the Z bit is set. Description: The contents of register ‘f’ are complemented. If ‘d’ is ‘0’, the result is stored in the W register. If ‘d’ is ‘1’, the result is stored back in register ‘f’. Status Affected: Description: DS41236E-page 60 f f,d © 2009 Microchip Technology Inc. PIC12F508/509/16F505 DECF Decrement f INCF Syntax: [ label ] DECF f,d Syntax: [ label ] Operands: 0 ≤ f ≤ 31 d ∈ [0,1] Operands: 0 ≤ f ≤ 31 d ∈ [0,1] Operation: (f) – 1 → (dest) Operation: (f) + 1 → (dest) Status Affected: Z Status Affected: Z Description: Decrement register ‘f’. If ‘d’ is ‘0’, the result is stored in the W register. If ‘d’ is ‘1’, the result is stored back in register ‘f’. Description: The contents of register ‘f’ are incremented. If ‘d’ is ‘0’, the result is placed in the W register. If ‘d’ is ‘1’, the result is placed back in register ‘f’. DECFSZ Decrement f, Skip if 0 INCFSZ Increment f, Skip if 0 Syntax: [ label ] DECFSZ f,d Syntax: [ label ] Operands: 0 ≤ f ≤ 31 d ∈ [0,1] Operands: 0 ≤ f ≤ 31 d ∈ [0,1] Operation: (f) – 1 → d; Operation: (f) + 1 → (dest), skip if result = 0 Status Affected: None Status Affected: None Description: The contents of register ‘f’ are decremented. If ‘d’ is ‘0’, the result is placed in the W register. If ‘d’ is ‘1’, the result is placed back in register ‘f’. If the result is ‘0’, the next instruction, which is already fetched, is discarded and a NOP is executed instead making it a two-cycle instruction. Description: The contents of register ‘f’ are incremented. If ‘d’ is ‘0’, the result is placed in the W register. If ‘d’ is ‘1’, the result is placed back in register ‘f’. If the result is ‘0’, then the next instruction, which is already fetched, is discarded and a NOP is executed instead making it a two-cycle instruction. GOTO Unconditional Branch IORLW Inclusive OR literal with W Syntax: [ label ] Syntax: [ label ] Operands: 0 ≤ k ≤ 511 Operands: 0 ≤ k ≤ 255 Operation: k → PC<8:0>; STATUS<6:5> → PC<10:9> Operation: (W) .OR. (k) → (W) Status Affected: Z Status Affected: None Description: Description: GOTO is an unconditional branch. The 9-bit immediate value is loaded into PC bits <8:0>. The upper bits of PC are loaded from STATUS<6:5>. GOTO is a twocycle instruction. The contents of the W register are OR’ed with the eight-bit literal ‘k’. The result is placed in the W register. skip if result = 0 GOTO k © 2009 Microchip Technology Inc. Increment f INCF f,d INCFSZ f,d IORLW k DS41236E-page 61 PIC12F508/509/16F505 IORWF Inclusive OR W with f MOVWF Syntax: [ label ] Syntax: [ label ] Operands: 0 ≤ f ≤ 31 d ∈ [0,1] Operands: 0 ≤ f ≤ 31 Operation: (W).OR. (f) → (dest) (W) → (f) Operation: Status Affected: None Status Affected: Z Description: Description: Inclusive OR the W register with register ‘f’. If ‘d’ is ‘0’, the result is placed in the W register. If ‘d’ is ‘1’, the result is placed back in register ‘f’. Move data from the W register to register ‘f’. MOVF Move f NOP No Operation Syntax: [ label ] Syntax: [ label ] Operands: 0 ≤ f ≤ 31 d ∈ [0,1] Operands: None Operation: No operation IORWF f,d MOVF f,d Move W to f MOVWF f NOP Operation: (f) → (dest) Status Affected: None Status Affected: Z Description: No operation. Description: The contents of register ‘f’ are moved to destination ‘d’. If ‘d’ is ‘0’, destination is the W register. If ‘d’ is ‘1’, the destination is file register ‘f’. ‘d’ = 1 is useful as a test of a file register, since status flag Z is affected. MOVLW Move Literal to W OPTION Load OPTION Register Syntax: [ label ] Syntax: [ label ] Operands: 0 ≤ k ≤ 255 Operands: None Operation: k → (W) Operation: (W) → OPTION Status Affected: None Status Affected: None Description: The content of the W register is loaded into the OPTION register. Description: DS41236E-page 62 MOVLW k The eight-bit literal ‘k’ is loaded into the W register. The “don’t cares” will assembled as ‘0’s. OPTION © 2009 Microchip Technology Inc. PIC12F508/509/16F505 RETLW Return with Literal in W SLEEP Enter SLEEP Mode Syntax: [ label ] Syntax: [label ] Operands: 0 ≤ k ≤ 255 Operands: None Operation: k → (W); TOS → PC Operation: Status Affected: None Description: The W register is loaded with the eight-bit literal ‘k’. The program counter is loaded from the top of the stack (the return address). This is a two-cycle instruction. 00h → WDT; 0 → WDT prescaler; 1 → TO; 0 → PD Status Affected: TO, PD, RBWUF Description: Time-out Status bit (TO) is set. The Power-down Status bit (PD) is cleared. RBWUF is unaffected. The WDT and its prescaler are cleared. The processor is put into Sleep mode with the oscillator stopped. See Section 7.9 “Power-down Mode (Sleep)” on Sleep for more details. RLF Rotate Left f through Carry SUBWF Subtract W from f Syntax: [ label ] Syntax: [label ] Operands: 0 ≤ f ≤ 31 d ∈ [0,1] Operands: 0 ≤ f ≤ 31 d ∈ [0,1] Operation: See description below Operation: (f) – (W) → (dest) Status Affected: C Status Affected: C, DC, Z Description: The contents of register ‘f’ are rotated one bit to the left through the Carry flag. If ‘d’ is ‘0’, the result is placed in the W register. If ‘d’ is ‘1’, the result is stored back in register ‘f’. Description: Subtract (2’s complement method) the W register from register ‘f’. If ‘d’ is ‘0’, the result is stored in the W register. If ‘d’ is ‘1’, the result is stored back in register ‘f’. RETLW k RLF f,d SLEEP SUBWF f,d register ‘f’ C RRF Rotate Right f through Carry SWAPF Swap Nibbles in f Syntax: [ label ] Syntax: [ label ] SWAPF f,d Operands: 0 ≤ f ≤ 31 d ∈ [0,1] Operands: 0 ≤ f ≤ 31 d ∈ [0,1] Operation: See description below Operation: Status Affected: C (f<3:0>) → (dest<7:4>); (f<7:4>) → (dest<3:0>) Description: The contents of register ‘f’ are rotated one bit to the right through the Carry flag. If ‘d’ is ‘0’, the result is placed in the W register. If ‘d’ is ‘1’, the result is placed back in register ‘f’. Status Affected: None Description: The upper and lower nibbles of register ‘f’ are exchanged. If ‘d’ is ‘0’, the result is placed in W register. If ‘d’ is ‘1’, the result is placed in register ‘f’. RRF f,d C © 2009 Microchip Technology Inc. register ‘f’ DS41236E-page 63 PIC12F508/509/16F505 TRIS Load TRIS Register XORWF Syntax: [ label ] TRIS Syntax: [ label ] XORWF Operands: f=6 Operands: Operation: (W) → TRIS register f 0 ≤ f ≤ 31 d ∈ [0,1] f Exclusive OR W with f f,d Status Affected: None Operation: (W) .XOR. (f) → (dest) Description: TRIS register ‘f’ (f = 6 or 7) is loaded with the contents of the W register Status Affected: Z Description: Exclusive OR the contents of the W register with register ‘f’. If ‘d’ is ‘0’, the result is stored in the W register. If ‘d’ is ‘1’, the result is stored back in register ‘f’. XORLW Exclusive OR literal with W Syntax: [label ] Operands: 0 ≤ k ≤ 255 Operation: (W) .XOR. k → (W) XORLW k Status Affected: Z Description: The contents of the W register are XOR’ed with the eight-bit literal ‘k’. The result is placed in the W register. DS41236E-page 64 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 9.0 DEVELOPMENT SUPPORT The PIC® microcontrollers are supported with a full range of hardware and software development tools: • Integrated Development Environment - MPLAB® IDE Software • Assemblers/Compilers/Linkers - MPASMTM Assembler - MPLAB C18 and MPLAB C30 C Compilers - MPLINKTM Object Linker/ MPLIBTM Object Librarian - MPLAB ASM30 Assembler/Linker/Library • Simulators - MPLAB SIM Software Simulator • Emulators - MPLAB ICE 2000 In-Circuit Emulator - MPLAB REAL ICE™ In-Circuit Emulator • In-Circuit Debugger - MPLAB ICD 2 • Device Programmers - PICSTART® Plus Development Programmer - MPLAB PM3 Device Programmer - PICkit™ 2 Development Programmer • Low-Cost Demonstration and Development Boards and Evaluation Kits 9.1 MPLAB Integrated Development Environment Software The MPLAB IDE software brings an ease of software development previously unseen in the 8/16-bit microcontroller market. The MPLAB IDE is a Windows® operating system-based application that contains: • A single graphical interface to all debugging tools - Simulator - Programmer (sold separately) - Emulator (sold separately) - In-Circuit Debugger (sold separately) • A full-featured editor with color-coded context • A multiple project manager • Customizable data windows with direct edit of contents • High-level source code debugging • Visual device initializer for easy register initialization • Mouse over variable inspection • Drag and drop variables from source to watch windows • Extensive on-line help • Integration of select third party tools, such as HI-TECH Software C Compilers and IAR C Compilers The MPLAB IDE allows you to: • Edit your source files (either assembly or C) • One touch assemble (or compile) and download to PIC MCU emulator and simulator tools (automatically updates all project information) • Debug using: - Source files (assembly or C) - Mixed assembly and C - Machine code MPLAB IDE supports multiple debugging tools in a single development paradigm, from the cost-effective simulators, through low-cost in-circuit debuggers, to full-featured emulators. This eliminates the learning curve when upgrading to tools with increased flexibility and power. © 2009 Microchip Technology Inc. DS41236E-page 65 PIC12F508/509/16F505 9.2 MPASM Assembler The MPASM Assembler is a full-featured, universal macro assembler for all PIC MCUs. The MPASM Assembler generates relocatable object files for the MPLINK Object Linker, Intel® standard HEX files, MAP files to detail memory usage and symbol reference, absolute LST files that contain source lines and generated machine code and COFF files for debugging. The MPASM Assembler features include: • Integration into MPLAB IDE projects • User-defined macros to streamline assembly code • Conditional assembly for multi-purpose source files • Directives that allow complete control over the assembly process 9.5 MPLAB ASM30 Assembler produces relocatable machine code from symbolic assembly language for dsPIC30F devices. MPLAB C30 C Compiler uses the assembler to produce its object file. The assembler generates relocatable object files that can then be archived or linked with other relocatable object files and archives to create an executable file. Notable features of the assembler include: • • • • • • Support for the entire dsPIC30F instruction set Support for fixed-point and floating-point data Command line interface Rich directive set Flexible macro language MPLAB IDE compatibility 9.6 9.3 MPLAB C18 and MPLAB C30 C Compilers The MPLAB C18 and MPLAB C30 Code Development Systems are complete ANSI C compilers for Microchip’s PIC18 and PIC24 families of microcontrollers and the dsPIC30 and dsPIC33 family of digital signal controllers. These compilers provide powerful integration capabilities, superior code optimization and ease of use not found with other compilers. For easy source level debugging, the compilers provide symbol information that is optimized to the MPLAB IDE debugger. 9.4 MPLINK Object Linker/ MPLIB Object Librarian The MPLINK Object Linker combines relocatable objects created by the MPASM Assembler and the MPLAB C18 C Compiler. It can link relocatable objects from precompiled libraries, using directives from a linker script. MPLAB ASM30 Assembler, Linker and Librarian MPLAB SIM Software Simulator The MPLAB SIM Software Simulator allows code development in a PC-hosted environment by simulating the PIC MCUs and dsPIC® DSCs on an instruction level. On any given instruction, the data areas can be examined or modified and stimuli can be applied from a comprehensive stimulus controller. Registers can be logged to files for further run-time analysis. The trace buffer and logic analyzer display extend the power of the simulator to record and track program execution, actions on I/O, most peripherals and internal registers. The MPLAB SIM Software Simulator fully supports symbolic debugging using the MPLAB C18 and MPLAB C30 C Compilers, and the MPASM and MPLAB ASM30 Assemblers. The software simulator offers the flexibility to develop and debug code outside of the hardware laboratory environment, making it an excellent, economical software development tool. The MPLIB Object Librarian manages the creation and modification of library files of precompiled code. When a routine from a library is called from a source file, only the modules that contain that routine will be linked in with the application. This allows large libraries to be used efficiently in many different applications. The object linker/library features include: • Efficient linking of single libraries instead of many smaller files • Enhanced code maintainability by grouping related modules together • Flexible creation of libraries with easy module listing, replacement, deletion and extraction DS41236E-page 66 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 9.7 MPLAB ICE 2000 High-Performance In-Circuit Emulator The MPLAB ICE 2000 In-Circuit Emulator is intended to provide the product development engineer with a complete microcontroller design tool set for PIC microcontrollers. Software control of the MPLAB ICE 2000 In-Circuit Emulator is advanced by the MPLAB Integrated Development Environment, which allows editing, building, downloading and source debugging from a single environment. The MPLAB ICE 2000 is a full-featured emulator system with enhanced trace, trigger and data monitoring features. Interchangeable processor modules allow the system to be easily reconfigured for emulation of different processors. The architecture of the MPLAB ICE 2000 In-Circuit Emulator allows expansion to support new PIC microcontrollers. The MPLAB ICE 2000 In-Circuit Emulator system has been designed as a real-time emulation system with advanced features that are typically found on more expensive development tools. The PC platform and Microsoft® Windows® 32-bit operating system were chosen to best make these features available in a simple, unified application. 9.8 MPLAB REAL ICE In-Circuit Emulator System MPLAB REAL ICE In-Circuit Emulator System is Microchip’s next generation high-speed emulator for Microchip Flash DSC and MCU devices. It debugs and programs PIC® Flash MCUs and dsPIC® Flash DSCs with the easy-to-use, powerful graphical user interface of the MPLAB Integrated Development Environment (IDE), included with each kit. The MPLAB REAL ICE probe is connected to the design engineer’s PC using a high-speed USB 2.0 interface and is connected to the target with either a connector compatible with the popular MPLAB ICD 2 system (RJ11) or with the new high-speed, noise tolerant, LowVoltage Differential Signal (LVDS) interconnection (CAT5). 9.9 MPLAB ICD 2 In-Circuit Debugger Microchip’s In-Circuit Debugger, MPLAB ICD 2, is a powerful, low-cost, run-time development tool, connecting to the host PC via an RS-232 or high-speed USB interface. This tool is based on the Flash PIC MCUs and can be used to develop for these and other PIC MCUs and dsPIC DSCs. The MPLAB ICD 2 utilizes the in-circuit debugging capability built into the Flash devices. This feature, along with Microchip’s In-Circuit Serial ProgrammingTM (ICSPTM) protocol, offers costeffective, in-circuit Flash debugging from the graphical user interface of the MPLAB Integrated Development Environment. This enables a designer to develop and debug source code by setting breakpoints, single stepping and watching variables, and CPU status and peripheral registers. Running at full speed enables testing hardware and applications in real time. MPLAB ICD 2 also serves as a development programmer for selected PIC devices. 9.10 MPLAB PM3 Device Programmer The MPLAB PM3 Device Programmer is a universal, CE compliant device programmer with programmable voltage verification at VDDMIN and VDDMAX for maximum reliability. It features a large LCD display (128 x 64) for menus and error messages and a modular, detachable socket assembly to support various package types. The ICSP™ cable assembly is included as a standard item. In Stand-Alone mode, the MPLAB PM3 Device Programmer can read, verify and program PIC devices without a PC connection. It can also set code protection in this mode. The MPLAB PM3 connects to the host PC via an RS-232 or USB cable. The MPLAB PM3 has high-speed communications and optimized algorithms for quick programming of large memory devices and incorporates an SD/MMC card for file storage and secure data applications. MPLAB REAL ICE is field upgradeable through future firmware downloads in MPLAB IDE. In upcoming releases of MPLAB IDE, new devices will be supported, and new features will be added, such as software breakpoints and assembly code trace. MPLAB REAL ICE offers significant advantages over competitive emulators including low-cost, full-speed emulation, real-time variable watches, trace analysis, complex breakpoints, a ruggedized probe interface and long (up to three meters) interconnection cables. © 2009 Microchip Technology Inc. DS41236E-page 67 PIC12F508/509/16F505 9.11 PICSTART Plus Development Programmer The PICSTART Plus Development Programmer is an easy-to-use, low-cost, prototype programmer. It connects to the PC via a COM (RS-232) port. MPLAB Integrated Development Environment software makes using the programmer simple and efficient. The PICSTART Plus Development Programmer supports most PIC devices in DIP packages up to 40 pins. Larger pin count devices, such as the PIC16C92X and PIC17C76X, may be supported with an adapter socket. The PICSTART Plus Development Programmer is CE compliant. 9.12 PICkit 2 Development Programmer The PICkit™ 2 Development Programmer is a low-cost programmer and selected Flash device debugger with an easy-to-use interface for programming many of Microchip’s baseline, mid-range and PIC18F families of Flash memory microcontrollers. The PICkit 2 Starter Kit includes a prototyping development board, twelve sequential lessons, software and HI-TECH’s PICC™ Lite C compiler, and is designed to help get up to speed quickly using PIC® microcontrollers. The kit provides everything needed to program, evaluate and develop applications using Microchip’s powerful, mid-range Flash memory family of microcontrollers. DS41236E-page 68 9.13 Demonstration, Development and Evaluation Boards A wide variety of demonstration, development and evaluation boards for various PIC MCUs and dsPIC DSCs allows quick application development on fully functional systems. Most boards include prototyping areas for adding custom circuitry and provide application firmware and source code for examination and modification. The boards support a variety of features, including LEDs, temperature sensors, switches, speakers, RS-232 interfaces, LCD displays, potentiometers and additional EEPROM memory. The demonstration and development boards can be used in teaching environments, for prototyping custom circuits and for learning about various microcontroller applications. In addition to the PICDEM™ and dsPICDEM™ demonstration/development board series of circuits, Microchip has a line of evaluation kits and demonstration software for analog filter design, KEELOQ® security ICs, CAN, IrDA®, PowerSmart battery management, SEEVAL® evaluation system, Sigma-Delta ADC, flow rate sensing, plus many more. Check the Microchip web page (www.microchip.com) for the complete list of demonstration, development and evaluation kits. © 2009 Microchip Technology Inc. PIC12F508/509/16F505 10.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings(†) Ambient temperature under bias.......................................................................................................... -40°C to +125°C Storage temperature ............................................................................................................................ -65°C to +150°C Voltage on VDD with respect to VSS ............................................................................................................... 0 to +6.5V Voltage on MCLR with respect to VSS..........................................................................................................0 to +13.5V Voltage on all other pins with respect to VSS ............................................................................... -0.3V to (VDD + 0.3V) Total power dissipation(1) .................................................................................................................................. 800 mW Max. current out of VSS pin ................................................................................................................................ 200 mA Max. current into VDD pin ................................................................................................................................... 150 mA Input clamp current, IIK (VI < 0 or VI > VDD)...................................................................................................................±20 mA Output clamp current, IOK (VO < 0 or VO > VDD) ...........................................................................................................±20 mA Max. output current sunk by any I/O pin .............................................................................................................. 25 mA Max. output current sourced by any I/O pin ......................................................................................................... 25 mA Max. output current sourced by I/O port .............................................................................................................. 75 mA Max. output current sunk by I/O port ................................................................................................................... 75 mA Note 1: Power dissipation is calculated as follows: PDIS = VDD x {IDD – ∑ IOH} + ∑ {(VDD – VOH) x IOH} + ∑(VOL x IOL) †NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. © 2009 Microchip Technology Inc. DS41236E-page 69 PIC12F508/509/16F505 PIC12F508/509/16F505 VOLTAGE-FREQUENCY GRAPH, -40°C ≤ TA ≤ +125°C FIGURE 10-1: 6.0 5.5 (PIC16F505 only) 5.0 4.5 VDD (Volts) 4.0 3.5 3.0 2.5 2.0 0 4 8 10 20 25 Frequency (MHz) FIGURE 10-2: MAXIMUM OSCILLATOR FREQUENCY TABLE Oscillator Mode LP XT INTOSC EXTRC EC(1) HS(1) 0 200 kHz 4 MHz 20 MHz Frequency (MHz) Note 1: DS41236E-page 70 For PIC16F505 only. © 2009 Microchip Technology Inc. PIC12F508/509/16F505 10.1 DC Characteristics: PIC12F508/509/16F505 (Industrial) Standard Operating Conditions (unless otherwise specified) Operating Temperature -40°C ≤ TA ≤ +85°C (industrial) DC Characteristics Param Sym. No. D001 VDD Characteristic Supply Voltage VDR D003 VPOR VDD Start Voltage to ensure Power-on Reset D004 SVDD VDD Rise Rate to ensure Power-on Reset IDD D020 IPD D022 IWDT * Note 1: 2: 3: 4: 5: Typ(1) Max. 2.0 (2) D002 D010 Min. RAM Data Retention Voltage 5.5 Units V Conditions See Figure 10-1 — 1.5* — V Device in Sleep mode — Vss — V See Section 7.4 "Power-on Reset (POR)" for details 0.05* — — V/ms See Section 7.4 "Power-on Reset (POR)" for details — — 175 0.625 275 1.1 μA mA FOSC = 4 MHz, VDD = 2.0V FOSC = 4 MHz, VDD = 5.0V — — 500 1.5 650 2.2 μA mA FOSC = 10 MHz, VDD = 3.0V FOSC = 20 MHz, VDD = 5.0V (PIC16F505 only) — — 11 38 20 54 μA μA FOSC = 32 kHz, VDD = 2.0V FOSC = 32 kHz, VDD = 5.0V Power-down Current(5) — — 0.1 0.35 1.2 2.4 μA μA VDD = 2.0V VDD = 5.0V WDT Current(5) — — 1.0 7.0 3.0 16.0 μA μA VDD = 2.0V VDD = 5.0V Supply Current(3,4) These parameters are characterized but not tested. Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance only and is not tested. This is the limit to which VDD can be lowered in Sleep mode without losing RAM data. The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus loading, oscillator type, bus rate, internal code execution pattern and temperature also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VSS, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified. For standby current measurements, the conditions are the same as IDD, except that the device is in Sleep mode. If a module current is listed, the current is for that specific module enabled and the device in Sleep. © 2009 Microchip Technology Inc. DS41236E-page 71 PIC12F508/509/16F505 10.2 DC Characteristics: PIC12F508/509/16F505 (Extended) Standard Operating Conditions (unless otherwise specified) Operating Temperature -40°C ≤ TA ≤ +125°C (extended) DC Characteristics Param No. Sym. D001 VDD Characteristic Supply Voltage D002 VDR VPOR VDD Start Voltage to ensure Power-on Reset D004 SVDD VDD Rise Rate to ensure Power-on Reset IDD D020 IPD D022 IWDT * Note 1: 2: 3: 4: 5: Typ(1) Max. 2.0 (2) D003 D010 Min. RAM Data Retention Voltage 5.5 Units V Conditions See Figure 10-1 — 1.5* — V Device in Sleep mode — Vss — V See Section 7.4 "Power-on Reset (POR)" for details 0.05* — — V/ms See Section 7.4 "Power-on Reset (POR)" for details — — 175 0.625 275 1.1 μA mA FOSC = 4 MHz, VDD = 2.0V FOSC = 4 MHz, VDD = 5.0V — — 500 1.5 650 2.2 μA mA FOSC = 10 MHz, VDD = 3.0V FOSC = 20 MHz, VDD = 5.0V (PIC16F515 only) — — 11 38 26 110 μA μA FOSC = 32 kHz, VDD = 2.0V FOSC = 32 kHz, VDD = 5.0V Power-down Current(5) — — 0.1 0.35 9.0 15.0 μA μA VDD = 2.0V VDD = 5.0V WDT Current(5) — — 1.0 7.0 18 22 μA μA VDD = 2.0V VDD = 5.0V Supply Current(3,4) These parameters are characterized but not tested. Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance only and is not tested. This is the limit to which VDD can be lowered in Sleep mode without losing RAM data. The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus loading, oscillator type, bus rate, internal code execution pattern and temperature also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VSS, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified. For standby current measurements, the conditions are the same as IDD, except that the device is in Sleep mode. If a module current is listed, the current is for that specific module enabled and the device in Sleep. DS41236E-page 72 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 TABLE 10-1: DC CHARACTERISTICS: PIC12F508/509/16F505 (Industrial, Extended) Standard Operating Conditions (unless otherwise specified) Operating temperature -40°C ≤ TA ≤ +85°C (industrial) -40°C ≤ TA ≤ +125°C (extended) Operating voltage VDD range as described in DC specification DC CHARACTERISTICS Param No. Sym. VIL Characteristic Min. Typ† Max. Units Conditions Input Low Voltage I/O ports: D030 with TTL buffer D030A D031 with Schmitt Trigger buffer Vss — 0.8V V For all 4.5 ≤ VDD ≤ 5.5V Vss — 0.15 VDD V Otherwise Vss — 0.15 VDD V D032 MCLR, T0CKI Vss — 0.15 VDD V D033 OSC1 (in EXTRC) Vss — 0.15 VDD V (Note1) D033 OSC1 (in HS) Vss — 0.3 VDD V (Note1) D033 OSC1 (in XT and LP) Vss — 0.3 V (Note1) 2.0 — VDD V 4.5 ≤ VDD ≤ 5.5V 0.25 VDD + 0.8 — VDD V Otherwise For entire VDD range VIH Input High Voltage I/O ports: D040 with TTL buffer D040A D041 with Schmitt Trigger buffer — 0.85 VDD — VDD V D042 MCLR, T0CKI 0.85 VDD — VDD V D043 OSC1 (in EXTRC) 0.85 VDD — VDD V (Note1) D043 OSC1 (in HS) 0.7 VDD — VDD V (Note1) D043 OSC1 (in XT and LP) 1.6 — VDD V GPIO/PORTB weak pull-up current(4) 50 250 400 μA D070 IPUR IIL VDD = 5V, VPIN = VSS Input Leakage Current(2), (3) D060 I/O ports — — ±1 μA Vss ≤ VPIN ≤ VDD, Pin at high-impedance D061 GP3/RB3/MCLRI(5) — ± 0.7 ±5 μA Vss ≤ VPIN ≤ VDD D063 OSC1 — — ±5 μA Vss ≤ VPIN ≤ VDD, XT, HS and LP oscillator configuration D080 I/O ports/CLKOUT — — 0.6 V IOL = 8.5 mA, VDD = 4.5V, -40°C to +85°C — — 0.6 V IOL = 7.0 mA, VDD = 4.5V, -40°C to +125°C — — 0.6 V IOL = 1.6 mA, VDD = 4.5V, -40°C to +85°C — — 0.6 V IOL = 1.2 mA, VDD = 4.5V, -40°C to +125°C Output Low Voltage D080A D083 OSC2 D083A Output High Voltage I/O ports/CLKOUT(3) D090 VDD – 0.7 — — V IOH = -3.0 mA, VDD = 4.5V, -40°C to +85°C VDD – 0.7 — — V IOH = -2.5 mA, VDD = 4.5V, -40°C to +125°C VDD – 0.7 — — V IOH = -1.3 mA, VDD = 4.5V, -40°C to +85°C VDD – 0.7 — — V IOH = -1.0 mA, VDD = 4.5V, -40°C to +125°C OSC2 pin — — 15 pF In XT, HS and LP modes when external clock is used to drive OSC1. All I/O pins and OSC2 — — 50 pF D090A D092 OSC2 D092A Capacitive Loading Specs on Output Pins D100 D101 Note † 1: 2: 3: 4: 5: Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. In EXTRC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC12F508/509/ 16F505 be driven with external clock in RC mode. The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. Negative current is defined as coming out of the pin. The specification applies to all weak pull-up devices, including the weak pull-up on GP3/MCLR. The current listed will be the same whether GP3/MCLR is configured as GP3 with a weak pull-up or enabled as MCLR. This specification applies when GP3/RB3/MCLR is configured as an input with pull-up disabled. The leakage current of the MCLR circuit is higher than the standard I/O logic. © 2009 Microchip Technology Inc. DS41236E-page 73 PIC12F508/509/16F505 TABLE 10-2: VDD (Volts) PULL-UP RESISTOR RANGES – PIC12F508/509/16F505 Temperature (°C) GP0(RBO)/GP1(RB1) 2.0 5.5 GP3(RB3) 2.0 5.5 * –40 25 85 125 –40 25 85 125 Min. Typ. Max. 73K 73K 82K 86K 15K 15K 19K 23K 105K 113K 123K 132k 21K 22K 26k 29K 186K 187K 190K 190K 33K 34K 35K 35K 81K 93K 96k 100K 20k 21K 25k 27K 96K 116K 116K 119K 22K 23K 28K 29K –40 63K 25 77K 85 82K 125 86K –40 16K 25 16K 85 24K 125 26K These parameters are characterized but not tested. DS41236E-page 74 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 10.3 Timing Parameter Symbology and Load Conditions – PIC12F508/509/16F505 The timing parameter symbols have been created following one of the following formats: 1. TppS2ppS 2. TppS T F Frequency T Time Lowercase subscripts (pp) and their meanings: pp 2 to mc MCLR ck CLKOUT osc Oscillator cy Cycle time os OSC1 drt Device Reset Timer t0 T0CKI io I/O port wdt Watchdog Timer Uppercase letters and their meanings: S F Fall P Period H High R Rise I Invalid (high-impedance) V Valid L Low Z High-impedance FIGURE 10-3: LOAD CONDITIONS – PIC12F508/509/16F505 Legend: CL pin CL = 50 pF for all pins except OSC2 15 pF for OSC2 in XT, HS or LP modes when external clock is used to drive OSC1 VSS FIGURE 10-4: EXTERNAL CLOCK TIMING – PIC12F508/509/16F505 Q4 Q1 Q3 Q2 Q4 Q1 OSC1 1 3 3 4 4 2 © 2009 Microchip Technology Inc. DS41236E-page 75 PIC12F508/509/16F505 TABLE 10-3: EXTERNAL CLOCK TIMING REQUIREMENTS – PIC12F508/509/16F505 AC CHARACTERISTICS Standard Operating Conditions (unless otherwise specified) Operating Temperature -40°C ≤ TA ≤ +85°C (industrial), -40°C ≤ TA ≤ +125°C (extended) Operating Voltage VDD range is described in Section 10.1 "Poweron Reset (POR)" Param No. Sym. Characteristic Min. Typ(1) 1A FOSC External CLKIN Frequency(2) DC — 4 MHz XT Oscillator mode DC — 20 MHz EC, HS Oscillator mode (PIC16F505 only) DC — 200 kHz — — 4 Oscillator Frequency 1 TOSC External CLKIN (2) Period(2) Oscillator Period (2) Max. Units Conditions LP Oscillator mode MHz EXTRC Oscillator mode 0.1 — 4 MHz XT Oscillator mode 4 — 20 MHz HS Oscillator mode (PIC16F505 only) — — 200 kHz 250 — — ns XT Oscillator mode 50 — — ns EC, HS Oscillator mode (PIC16F505 only) 5 — — μs LP Oscillator mode 250 — — ns EXTRC Oscillator mode 250 — 10,000 ns XT Oscillator mode 50 — 250 ns HS Oscillator mode (PIC16F505 only) LP Oscillator mode LP Oscillator mode 5 — — μs 2 TCY Instruction Cycle Time 200 4/FOSC — ns 3 TosL, TosH Clock in (OSC1) Low or High Time 50* — — ns XT Oscillator 2* — — μs LP Oscillator 10* — — ns EC, HS Oscillator (PIC16F505 only) — — 25* ns XT Oscillator — — 50* ns LP Oscillator — — 15* ns EC, HS Oscillator (PIC16F505 only) 4 TosR, TosF * Note 1: 2: Clock in (OSC1) Rise or Fall Time These parameters are characterized but not tested. Data in the Typical (“Typ”) column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices. DS41236E-page 76 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 TABLE 10-4: CALIBRATED INTERNAL RC FREQUENCIES – PIC12F508/509/16F505 AC CHARACTERISTICS Standard Operating Conditions (unless otherwise specified) Operating Temperature -40°C ≤ TA ≤ +85°C (industrial), -40°C ≤ TA ≤ +125°C (extended) Param No. Freq Min. Tolerance F10 Sym. FOSC Characteristic Internal Calibrated INTOSC Frequency(1) Typ† Max. Units Conditions ± 1% 3.96 4.00 4.04 MHz VDD = 3.5V, TA = 25°C ± 2% 3.92 4.00 4.08 MHz 2.5V ≤ VDD ≤ 5.5V 0°C ≤ TA ≤ +85°C ± 5% 3.80 4.00 4.20 MHz 2.0V ≤ VDD ≤ 5.5V -40°C ≤ TA ≤ +85°C (Ind.) -40°C ≤ TA ≤ +125°C (Ext.) * These parameters are characterized but not tested. † Data in the Typical (“Typ”) column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: To ensure these oscillator frequency tolerances, VDD and VSS must be capacitively decoupled as close to the device as possible. 0.1 uF and 0.01 uF values in parallel are recommended. FIGURE 10-5: I/O TIMING – PIC12F508/509/16F505 Q1 Q4 Q2 Q3 OSC1 I/O Pin (input) 17 I/O Pin (output) 19 18 New Value Old Value 20, 21 Note: All tests must be done with specified capacitive loads (see data sheet) 50 pF on I/O pins and CLKOUT. © 2009 Microchip Technology Inc. DS41236E-page 77 PIC12F508/509/16F505 TABLE 10-5: TIMING REQUIREMENTS – PIC12F508/509/16F505 Standard Operating Conditions (unless otherwise specified) AC Operating Temperature -40°C ≤ TA ≤ +85°C (industrial) CHARACTERISTICS -40°C ≤ TA ≤ +125°C (extended) Operating Voltage VDD range is described in Section 10.1 "Power-on Reset (POR)" Param No. 17 Sym. TOSH2IOV Characteristic Min. Typ(1) Max. Units — — 100* ns OSC1↑ (Q1 cycle) to Port Out Valid(2), (3) (2) 18 TOSH2IOI OSC1↑ (Q2 cycle) to Port Input Invalid (I/O in hold time) 50 — — ns 19 TIOV2OSH Port Input Valid to OSC1↑ (I/O in setup time) 20 — — ns — 10 25** ns — 10 25** ns 20 21 TIOR TIOF Port Output Rise Time Port Output Fall Time (3) (3) * These parameters are characterized but not tested. ** These parameters are design targets and are not tested. Note 1: Data in the Typical (“Typ”) column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. 2: Measurements are taken in EXTRC mode. 3: See Figure 10-3 for loading conditions. FIGURE 10-6: RESET, WATCHDOG TIMER AND DEVICE RESET TIMER TIMING – PIC12F508/509/16F505 VDD MCLR 30 Internal POR 32 32 32 DRT Timeout(2) Internal Reset Watchdog Timer Reset 31 34 34 I/O pin(1) Note 1: 2: I/O pins must be taken out of High-Impedance mode by enabling the output drivers in software. Runs in MCLR or WDT Reset only in XT, LP and HS (PIC16F505) modes. DS41236E-page 78 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 TABLE 10-6: RESET, WATCHDOG TIMER AND DEVICE RESET TIMER – PIC12F508/509/16F505 Standard Operating Conditions (unless otherwise specified) Operating Temperature -40°C ≤ TA ≤ +85°C (industrial) -40°C ≤ TA ≤ +125°C (extended) AC CHARACTERISTICS Param No. Sym. Characteristic Min. Typ(1) Max. Units 30 TMCL MCLR Pulse Width (low) 2000* — — ns VDD = 5.0V 31 TWDT Watchdog Timer Time-out Period (no prescaler) 9* 9* 18* 18* 30* 40* ms ms VDD = 5.0V (Industrial) VDD = 5.0V (Extended) 32 TDRT Device Reset Timer Period(2) 9* 9* 18* 18* 30* 40* ms ms VDD = 5.0V (Industrial) VDD = 5.0V (Extended) 34 TIOZ I/O High-impedance from MCLR low — — 2000* ns * Note 1: Conditions These parameters are characterized but not tested. Data in the Typical (“Typ”) column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. © 2009 Microchip Technology Inc. DS41236E-page 79 PIC12F508/509/16F505 FIGURE 10-7: TIMER0 CLOCK TIMINGS – PIC12F508/509/16F505 T0CKI 40 41 42 TABLE 10-7: TIMER0 CLOCK REQUIREMENTS – PIC12F508/509/16F505 Standard Operating Conditions (unless otherwise specified) Operating Temperature -40°C ≤ TA ≤ +85°C (industrial) -40°C ≤ TA ≤ +125°C (extended) Operating Voltage VDD range is described in Section 10.1 "Power-on Reset (POR)" AC CHARACTERISTICS Param Sym. No. 40 41 42 * Note 1: Tt0H Tt0L Tt0P Characteristic T0CKI High Pulse Width No Prescaler T0CKI Low Pulse Width No Prescaler T0CKI Period With Prescaler With Prescaler Min. Typ(1) Max. Units 0.5 TCY + 20* — — ns 10* — — ns 0.5 TCY + 20* — — ns 10* — — ns 20 or TCY + 40* N — — ns Conditions Whichever is greater. N = Prescale Value (1, 2, 4,..., 256) These parameters are characterized but not tested. Data in the Typical (“Typ”) column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. DS41236E-page 80 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 11.0 DC AND AC CHARACTERISTICS GRAPHS AND CHARTS Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore, outside the warranted range. “Typical” represents the mean of the distribution at 25°C. “Maximum” or “minimum” represents (mean + 3σ) or (mean 3σ) respectively, where s is a standard deviation, over each temperature range. FIGURE 11-1: IDD vs. VDD at FOSC = 4 MHz 1,400 1,200 Typical: Statistical Mean @25°C Maximum: Mean (Worst-Case Temp) + 3σ (-40°C to 125°C) Maximum 1,000 IDD (μA) 4 MHz 800 Typical 600 4 MHz 400 200 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VDD (V) © 2009 Microchip Technology Inc. DS41236E-page 81 PIC12F508/509/16F505 FIGURE 11-2: IDD VS. FOSC Over VDD (HS MODE, PIC16F505 only) 3.00 Typical: Statistical Mean @25°C Maximum: Mean (Worst-Case Temp) + 3σ (-40°C to 125°C) 2.50 Max. 5V IDD (mA) 2.00 Typical 5V 1.50 1.00 Max. 3V 0.50 Typical 3V 0.00 10 5 15 25 20 Fosc (MHz) FIGURE 11-3: TYPICAL IPD vs. VDD (SLEEP MODE, ALL PERIPHERALS DISABLED) Typical (Sleep Mode all Peripherals Disabled) 0.45 0.40 Typical: Statistical Mean @25°C Maximum: Mean (Worst-Case Temp) + 3σ (-40°C to 125°C) 0.35 IPD (μA) 0.30 0.25 0.20 0.15 0.10 0.05 0.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VDD (V) DS41236E-page 82 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 FIGURE 11-4: MAXIMUM IPD vs. VDD (SLEEP MODE, ALL PERIPHERALS DISABLED) Maximum (Sleep Mode all Peripherals Disabled) 18.0 16.0 Typical: Statistical Mean @25°C Maximum: Mean (Worst-Case Temp) + 3σ (-40°C to 125°C) 14.0 Max. 125°C IPD (μA) 12.0 10.0 8.0 6.0 4.0 Max. 85°C 2.0 0.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VDD (V) TYPICAL WDT IPD vs. VDD FIGURE 11-5: 9 8 7 Typical: Statistical Mean @25°C Maximum: Mean (Worst-Case Temp) + 3σ (-40°C to 125°C) IPD (μA) 6 5 4 3 2 1 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VDD (V) © 2009 Microchip Technology Inc. DS41236E-page 83 PIC12F508/509/16F505 FIGURE 11-6: MAXIMUM WDT IPD vs. VDD OVER TEMPERATURE Maximum 25.0 20.0 Typical: Statistical Mean @25°C Maximum: Mean (Worst-Case Temp) + 3σ (-40°C to 125°C) IPD (μA) Max. 125°C 15.0 10.0 Max. 85°C 5.0 0.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VDD (V) WDT TIME-OUT or DEVICE RESET TIMER vs. VDD OVER TEMPERATURE (NO WDT PRESCALER)(1) FIGURE 11-7: 50 Typical: Statistical Mean @25°C Maximum: Mean (Worst-Case Temp) + 3σ (-40°C to 125°C) Max. 125°C 45 40 Max. 85°C 35 Time (ms) 30 Typical. 25°C 25 20 Min. -40°C 15 10 5 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VDD (V) Note 1: Device Reset Timer (DRT) values are for case of Reset of power-up. Table 7-6 shows DRT values for the case of other types of Reset events. DS41236E-page 84 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 FIGURE 11-8: VOL vs. IOL OVER TEMPERATURE (VDD = 3.0V) (VDD = 3V, -40×C TO 125×C) 0.8 Typical: Statistical Mean @25°C Maximum: Mean (Worst-Case Temp) + 3σ (-40°C to 125°C) 0.7 Max. 125°C 0.6 VOL (V) 0.5 Max. 85°C 0.4 Typical 25°C 0.3 0.2 Min. -40°C 0.1 0.0 5.0 5.5 6.0 6.5 7.0 7.5 8.0 8.5 9.0 9.5 10.0 IOL (mA) FIGURE 11-9: VOL vs. IOL OVER TEMPERATURE (VDD = 5.0V) 0.45 Typical: Statistical Mean @25°C Typical: Statistical Mean @25×C Maximum: Mean (Worst-Case Temp) + 3σ Maximum: Meas(-40×C + 3 to 125×C) (-40°C to 125°C) 0.40 Max. 125°C 0.35 Max. 85°C VOL (V) 0.30 0.25 Typ. 25°C 0.20 0.15 Min. -40°C 0.10 0.05 0.00 5.0 5.5 6.0 6.5 7.0 7.5 8.0 8.5 9.0 9.5 10.0 IOL (mA) © 2009 Microchip Technology Inc. DS41236E-page 85 PIC12F508/509/16F505 FIGURE 11-10: VOH vs. IOH OVER TEMPERATURE (VDD = 3.0V) 3.5 3.0 Max. -40°C Typ. 25°C 2.5 Min. 125°C VOH (V) 2.0 1.5 1.0 Typical: Statistical Mean @25°C Maximum: Mean (Worst-Case Temp) + 3σ (-40°C to 125°C) 0.5 0.0 0.0 -0.5 -1.0 -1.5 -2.0 -2.5 -3.0 -3.5 -4.0 IOH (mA) FIGURE 11-11: (VDD = 5.0V) VOH vs. IOH OVER TEMPERATURE ( , ) 5.5 5.0 Max. -40°C Typ. 25°C VOH (V) 4.5 Min. 125°C 4.0 3.5 Typical: Statistical Mean @25°C Maximum: Mean (Worst-Case Temp) + 3σ (-40°C to 125°C) 3.0 0.0 -0.5 -1.0 -1.5 -2.0 -2.5 -3.0 -3.5 -4.0 -4.5 -5.0 IOH (mA) DS41236E-page 86 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 FIGURE 11-12: TTL INPUT THRESHOLD VIN vs. VDD (TTL Input, -40×C TO 125×C) 1.7 1.5 Typical: Statistical Mean @25°C Maximum: Mean (Worst-Case Temp) + 3σ (-40°C to 125°C) Max. -40°C VIN (V) 1.3 Typ. 25°C 1.1 Min. 125°C 0.9 0.7 0.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VDD (V) FIGURE 11-13: SCHMITT TRIGGER INPUT THRESHOLD VIN vs. VDD (ST Input, -40×C TO 125×C) 4.0 VIH Max. 125°C 3.5 Typical: Statistical Mean @25°C Maximum: Mean (Worst-Case Temp) + 3σ (-40°C to 125°C) VIH Min. -40°C VIN (V) 3.0 2.5 2.0 VIL Max. -40°C 1.5 VIL Min. 125°C 1.0 0.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VDD (V) © 2009 Microchip Technology Inc. DS41236E-page 87 PIC12F508/509/16F505 FIGURE 11-14: TYPICAL INTOSC FREQUENCY CHANGE vs VDD (25°C) 55 44 Change from Calibration (%) 33 22 11 00 -1-1 -2-2 -3-3 -4-4 -5-5 22 2.5 2.5 3 3 44 3.5 3.5 5 4.5 4.5 5.5 5.5 VDD (V) TYPICAL INTOSC FREQUENCY CHANGE vs VDD (-40°C) FIGURE 11-15: 55 44 Change from Calibration (%) 33 22 11 00 -1-1 -2-2 -3-3 -4-4 -5-5 22 2.5 2.5 33 3.5 3.5 44 4.5 4.5 55 5.5 5.5 VDD (V) DS41236E-page 88 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 FIGURE 11-16: TYPICAL INTOSC FREQUENCY CHANGE vs VDD (85°C) 5 44 Change from Calibration (%) 33 22 11 00 -1-1 -2-2 -3-3 -4 -4 -5-5 22 2.5 2.5 33 3.5 3.5 44 4.5 4.5 5 5.5 5.5 VDD (V) FIGURE 11-17: TYPICAL INTOSC FREQUENCY CHANGE vs VDD (125°C 5 44 Change from Calibration (%) 33 22 11 00 -1-1 -2-2 -3-3 -4 -4 -5-5 22 2.5 2.5 33 3.5 3.5 44 4.5 4.5 55 5.5 5.5 VDD (V) © 2009 Microchip Technology Inc. DS41236E-page 89 PIC12F508/509/16F505 NOTES: DS41236E-page 90 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 12.0 PACKAGING INFORMATION 12.1 Package Marking Information 8-Lead PDIP Example XXXXXXXX XXXXXNNN YYWW 12F508-I /P e3 017 0610 8-Lead SOIC (3.90 mm) XXXXXXXX XXXXYYWW NNN 8-Lead MSOP 8-Lead 2x3 DFN* XXX YWW NN Example Example BEQ 610 17 Legend: XX...X Y YY WW NNN e3 * * 12F509-I /SN e3 0610 017 12F509 0610017 XXXXXX YWWNNN Note: Example Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week ‘01’) Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line thus limiting the number of available characters for customer specific information. Standard PIC® device marking consists of Microchip part number, year code, week code, and traceability code. For PIC device marking beyond this, certain price adders apply. Please check with your Microchip Sales Office. For QTP devices, any special marking adders are included in QTP price. © 2009 Microchip Technology Inc. DS41236E-page 91 PIC12F508/509/16F505 12.1 Package Marking Information (Continued) 14-Lead PDIP (300 mil) XXXXXXXXXXXXXX XXXXXXXXXXXXXX YYWWNNN 14-Lead SOIC (3.90 mm) XXXXXXXXXXX XXXXXXXXXXX YYWWNNN 14-Lead TSSOP (4.4 mm) XXXXXXXX YYWW NNN 16-Lead QFN Example PIC16F505 -I/P e3 0215 0610017 Example PIC16F505-E /SL0125 0610017 Example 16F505-I 0610 017 Example XXXXXXX XXXXXXX 16F505 -I/MG YYWWNNN 0610017 TABLE 12-1: 8-LEAD 2X3 DFN (MC) TOP MARKING Part Number Marking PIC12F508 (T) - I/MC BN0 PIC12F508-E/MC BP0 PIC12F509 (T) - I/MC BQ0 PIC12F509-E/MC BR0 DS41236E-page 92 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 N NOTE 1 E1 1 3 2 D E A2 A L A1 c e eB b1 b 6&! '! 9'&! 7"') %! 7,8. 7 7 7: ; < & & & = = ##44!! - 1!& & = = "#& "#>#& . - - ##4>#& . < : 9& -< -? & & 9 - 9#4!! < ) ? ) < 1 = = 69#>#& 9 *9#>#& : *+ 1, - !"#$%&"' ()"&'"!&) &#*&&&# +%&,&!& - '! !#.# &"#' #%! &"! ! #%! &"! !! &$#/!# '! #& .0 1,21!'! &$& "! **& "&& ! * ,<1 © 2009 Microchip Technology Inc. DS41236E-page 93 PIC12F508/509/16F505 ! ""#$%& !' 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 D e N E E1 NOTE 1 1 2 3 α h b h A2 A c φ L A1 β L1 6&! '! 9'&! 7"') %! 99.. 7 7 7: ; < & : 8& = 1, = ##44!! = = &# %%+ = : >#& . ##4>#& . -1, : 9& 1, ?1, ,'%@ & A = 3 &9& 9 = 3 && 9 .3 3 & I B = <B 9#4!! = 9#>#& ) - = #%& D B = B #%&1 && ' E B = B !"#$%&"' ()"&'"!&) &#*&&&# +%&,&!& - '! !#.# &"#' #%! &"! ! #%! &"! !! &$#''!# '! #& .0 1,2 1!'! &$& "! **& "&& ! .32 %'! ("!"*& "&& (% % '& " !! * ,1 DS41236E-page 94 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 ! ""#$%& !' 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 © 2009 Microchip Technology Inc. DS41236E-page 95 PIC12F508/509/16F505 (" ! )*( ( ! 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 D N E E1 NOTE 1 1 2 e b A2 A c φ L L1 A1 6&! '! 9'&! 7"') %! 99.. 7 7 7: ; < & : 8& = ?1, = ##44!! < &# %% = : >#& . ##4>#& . -1, : 9& -1, 3 &9& 9 3 && 9 1, ? < .3 3 & I B = <B 9#4!! < = - 9#>#& ) = !"#$%&"' ()"&'"!&) &#*&&&# '! !#.# &"#' #%! &"! ! #%! &"! !! &$#''!# - '! #& .0 1,2 1!'! &$& "! **& "&& ! .32 %'! ("!"*& "&& (% % '& " !! * ,1 DS41236E-page 96 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 + $)*(',--%&+ 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 e D b N N L K E2 E EXPOSED PAD NOTE 1 NOTE 1 2 1 2 1 D2 BOTTOM VIEW TOP VIEW A A3 A1 NOTE 2 6&! '! 9'&! 7"') %! 99.. 7 7 7: ; < & : 8& < &# %% , &&4!! - .3 : 9& 1, : >#& . .$ !##9& - = .$ !##>#& . = ) - , &&9& 9 - , &&& .$ !## C = = , &&>#& 1, -1, !"#$%&"' ()"&'"!&) &#*&&&# 4' ' $ !#&)!&#! - 4!!*!"&# '! #& .0 1,2 1!'! &$& "! **& "&& ! .32 %'! ("!"*& "&& (% % '& " !! * ,-, © 2009 Microchip Technology Inc. DS41236E-page 97 PIC12F508/509/16F505 ./ 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 N NOTE 1 E1 1 3 2 D E A2 A L A1 c b1 b e eB 6&! '! 9'&! 7"') %! 7,8. 7 7 7: ; & & & = = ##44!! - 1!& & = = "#& "#>#& . - - ##4>#& . < : 9& - & & 9 - 9#4!! < ) ? ) < 1 = = 69#>#& 9 *9#>#& : *+ 1, - !"#$%&"' ()"&'"!&) &#*&&&# +%&,&!& - '! !#.# &"#' #%! &"! ! #%! &"! !! &$#/!# '! #& .0 1,21!'! &$& "! **& "&& ! * ,1 DS41236E-page 98 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 ./ ! ""#$%& !' 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 D N E E1 NOTE 1 1 2 3 e h b α h A A2 c φ L A1 β L1 6&! '! 9'&! 7"') %! 99.. 7 7 7: ; & : 8& = 1, = ##44!! = = &# %%+ = : >#& . ##4>#& . -1, : 9& <?1, ?1, ,'%@ & A = 3 &9& 9 = 3 && 9 .3 3 & I B = <B 9#4!! = 9#>#& ) - = #%& D B = B #%&1 && ' E B = B !"#$%&"' ()"&'"!&) &#*&&&# +%&,&!& - '! !#.# &"#' #%! &"! ! #%! &"! !! &$#''!# '! #& .0 1,2 1!'! &$& "! **& "&& ! .32 %'! ("!"*& "&& (% % '& " !! * ,?1 © 2009 Microchip Technology Inc. DS41236E-page 99 PIC12F508/509/16F505 ./ 01 1") ! 0/%/0 ! 3 &' !&"&4#*!(!!& 4%& &#& &&255***' '54 D N E E1 NOTE 1 1 2 e b c φ A2 A A1 6&! '! 9'&! 7"') %! L L1 99.. 7 7 7: ; & : 8& = ?1, = ##44!! < &# %% = : >#& . ##4>#& . - ?1, ##49& 3 &9& 9 ? 3 && 9 .3 3 & B = <B 9#4!! = 9#>#& ) = - !"#$%&"' ()"&'"!&) &#*&&&# '! !#.# &"#' #%! &"! ! #%! &"! !! &$#''!# - '! #& .0 1,2 1!'! &$& "! **& "&& ! .32 %'! ("!"*& "&& (% % '& " !! * ,<1 DS41236E-page 100 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging © 2009 Microchip Technology Inc. DS41236E-page 101 PIC12F508/509/16F505 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS41236E-page 102 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 APPENDIX A: REVISION HISTORY Revision A (April 2004) Original devices data sheet for PIC12F508/509/16F505 Revision B (June 2005) Update packages Revision C (03/2007) Revised Table 3-2 Legend; Revised Table 3-3 RB3 and Legend; Revised Table 10-4 F10; Replaced Package Drawings (Rev. AN); Added DFN package; Replaced Development Support Section; Revised Product ID System. Revision D (12/2007) Revised Title; Operating Current; Table 1-1 added DFN and revised note; Revised Section 3.0, last paragraph; Revised Figure 4-4; Revised Table 4-2 (FSR); Revised Register 7-1 and Register 7-2; Revised Section 7.2.2; Revised Table 7-3, Note 2; Revised Table 7-4 (FSR) and Note 2; Deleted Section 7.3.1: External Clock In and Figure 7-6; Revised new Section 7.3.1; Replaced TBD with new data in Tables 10-4 and 10-5; Revised Tables 10-1 (Industrial), 10-2 (Extended), and Tables 10-1 (Industrial, Extended) and 10-2 (Pull-up Resistor Ranges), 10-3, 10-4 and 10-6; Revised Figure 10-1, Figure 10-2; Section 11.0, Added Char data; Revised Package Marking Information; Revised Product ID System. Revision E (08/2009) Added PIC16F505 16-Pin diagram (QFN); Added Note after subsection 5.2 PORTC; Updated Note 4 and deleted Note 5, Table 10-1; Deleted Param. No. D061 (Table 10-1) and Param. No. D061A becomes D061; Added QFN Package Information; Revised Product Identification System; Added Figures 11-14, 11-15, 1116, 11-7 to Char Data section; Other minor corrections; Removed Preliminary status. © 2009 Microchip Technology Inc. DS41236E-page 103 PIC12F508/509/16F505 NOTES: DS41236E-page 104 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 INDEX A ALU ..................................................................................... 11 Assembler MPASM Assembler..................................................... 66 MPLAB Integrated Development Environment Software.... 65 MPLAB PM3 Device Programmer ...................................... 67 MPLAB REAL ICE In-Circuit Emulator System .................. 67 MPLINK Object Linker/MPLIB Object Librarian .................. 66 B O Block Diagram On-Chip Reset Circuit ................................................. 50 Timer0......................................................................... 35 TMR0/WDT Prescaler................................................. 39 Watchdog Timer.......................................................... 53 Brown-Out Protection Circuit .............................................. 54 Option Register................................................................... 24 OSC selection..................................................................... 41 OSCCAL Register............................................................... 26 Oscillator Configurations..................................................... 44 Oscillator Types HS............................................................................... 44 LP ............................................................................... 44 RC .............................................................................. 44 XT ............................................................................... 44 C C Compilers MPLAB C18 ................................................................ 66 MPLAB C30 ................................................................ 66 Carry ................................................................................... 11 Clocking Scheme ................................................................ 16 Code Protection ............................................................ 41, 55 Configuration Bits................................................................ 41 Configuration Word ............................................................. 43 Customer Change Notification Service ............................. 107 Customer Notification Service........................................... 107 Customer Support ............................................................. 107 D P PIC12F508/509/16F505 Device Varieties ............................ 9 PICSTART Plus Development Programmer....................... 68 POR Device Reset Timer (DRT) ................................... 41, 52 PD......................................................................... 54, 41 TO............................................................................... 54 PORTB ............................................................................... 31 Power-down Mode.............................................................. 55 Prescaler ............................................................................ 38 Program Counter ................................................................ 27 DC and AC Characteristics ................................................. 81 Development Support ......................................................... 65 Digit Carry ........................................................................... 11 Q E R Errata .................................................................................... 6 F Family of Devices PIC12F508/509/PIC16F505.......................................... 7 FSR ..................................................................................... 28 I I/O Interfacing ..................................................................... 31 I/O Ports .............................................................................. 31 I/O Programming Considerations........................................ 33 ID Locations .................................................................. 41, 55 INDF.................................................................................... 28 Indirect Data Addressing..................................................... 28 Instruction Cycle ................................................................. 16 Instruction Flow/Pipelining .................................................. 16 Instruction Set Summary..................................................... 58 Internet Address................................................................ 107 L Loading of PC ..................................................................... 27 M Memory Organization.......................................................... 17 Data Memory .............................................................. 18 Program Memory (PIC12F508/509)............................ 17 Program Memory (PIC16F505)................................... 18 Microchip Internet Web Site .............................................. 107 MPLAB ASM30 Assembler, Linker, Librarian ..................... 66 MPLAB ICD 2 In-Circuit Debugger ..................................... 67 MPLAB ICE 2000 High-Performance Universal In-Circuit Emulator ...................................................... 67 © 2009 Microchip Technology Inc. Q cycles .............................................................................. 16 RC Oscillator....................................................................... 45 Reader Response............................................................. 108 Read-Modify-Write.............................................................. 33 Register File Map PIC12F508 ................................................................. 19 PIC12F509 ................................................................. 19 PIC16F505 ................................................................. 19 Registers Special Function ......................................................... 20 Reset .................................................................................. 41 Reset on Brown-Out ........................................................... 54 S Sleep ............................................................................ 41, 55 Software Simulator (MPLAB SIM) ...................................... 66 Special Features of the CPU .............................................. 41 Special Function Registers ................................................. 20 Stack................................................................................... 27 Status Register ............................................................. 11, 22 T Timer0 Timer0 ........................................................................ 35 Timer0 (TMR0) Module .............................................. 35 TMR0 with External Clock .......................................... 37 Timing Diagrams and Specifications .................................. 75 Timing Parameter Symbology and Load Conditions .......... 75 TRIS Registers ................................................................... 31 DS41236E-page 105 PIC12F508/509/16F505 W Wake-up from Sleep ........................................................... 55 Watchdog Timer (WDT) ................................................ 41, 52 Period.......................................................................... 52 Programming Considerations ..................................... 52 WWW Address.................................................................. 107 WWW, On-Line Support........................................................ 6 Z Zero bit ................................................................................ 11 DS41236E-page 106 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 THE MICROCHIP WEB SITE CUSTOMER SUPPORT Microchip provides online support via our WWW site at www.microchip.com. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information: Users of Microchip products can receive assistance through several channels: • Product Support – Data sheets and errata, application notes and sample programs, design resources, user’s guides and hardware support documents, latest software releases and archived software • General Technical Support – Frequently Asked Questions (FAQ), technical support requests, online discussion groups, Microchip consultant program member listing • Business of Microchip – Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives • • • • • Distributor or Representative Local Sales Office Field Application Engineer (FAE) Technical Support Development Systems Information Line Customers should contact their distributor, representative or field application engineer (FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document. Technical support is available through the web site at: http://support.microchip.com CUSTOMER CHANGE NOTIFICATION SERVICE Microchip’s customer notification service helps keep customers current on Microchip products. Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest. To register, access the Microchip web site at www.microchip.com, click on Customer Change Notification and follow the registration instructions. © 2009 Microchip Technology Inc. DS41236E-page 107 PIC12F508/509/16F505 READER RESPONSE It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150. Please list the following information, and use this outline to provide us with your comments about this document. To: Technical Publications Manager RE: Reader Response Total Pages Sent ________ From: Name Company Address City / State / ZIP / Country Telephone: (_______) _________ - _________ FAX: (______) _________ - _________ Application (optional): Would you like a reply? Y Device: PIC12F508/509/16F505 N Literature Number: DS41236E Questions: 1. What are the best features of this document? 2. How does this document meet your hardware and software development needs? 3. Do you find the organization of this document easy to follow? If not, why? 4. What additions to the document do you think would enhance the structure and subject? 5. What deletions from the document could be made without affecting the overall usefulness? 6. Is there any incorrect or misleading information (what and where)? 7. How would you improve this document? DS41236E-page 108 © 2009 Microchip Technology Inc. PIC12F508/509/16F505 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. X /XX XXX Device Temperature Range Package Pattern Examples: a) b) Device: PIC16F505 PIC12F508 PIC12F509 PIC16F505T(1) PIC12F508T(2) PIC12F509T(2) Temperature Range: I E Package: MC MS P SL SN ST MG Pattern: Note: = = c) PIC12F508-E/P 301 = Extended Temp., PDIP package, QTP pattern #301 PIC12F508-I/SN = Industrial Temp., SOIC package PIC12F508T-E/P = Extended Temp., PDIP package, Tape and Reel -40°C to +85°C (Industrial) -40°C to +125°C (Extended) = = = = = = = 8L DFN 2x3 (DUAL Flatpack No-Leads)(3, 4) Micro-Small Outline Package (MSOP)(3, 4) Plastic (PDIP)(4) 14L Small Outline, 3.90 mm (SOIC)(4) 8L Small Outline, 3.90 mm Narrow (SOIC)(4) Thin Shrink Small Outline (TSSOP)(4) 16L QFN (3x3x0.9)(5) Special Requirements Note 1: 2: 3: 4: 5: T = in tape and reel SOIC, TSSOP and QFN packages only T = in tape and reel SOIC and MSOP packages only. PIC12F508/PIC12F509 only. Pb-free. PIC16F505 only. Tape and Reel available for only the following packages: SOIC, MSOP and TSSOP. © 2009 Microchip Technology Inc. DS41236E-page 109 WORLDWIDE SALES AND SERVICE AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://support.microchip.com Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4080 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Kokomo Kokomo, IN Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 Taiwan - Hsin Chu Tel: 886-3-6578-300 Fax: 886-3-6578-370 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 03/26/09 DS41236E-page 110 © 2009 Microchip Technology Inc.