PHILIPS SA630

RF COMMUNICATIONS PRODUCTS
OUTPUT/INPUT
INPUT/OUTPUT
OUTPUT/INPUT
ENCH1
SA630
Single pole double throw (SPDT) switch
Product Specification
Replaces data of October 10, 1991
IC17 Data Handbook
Philips Semiconductors
1997 Nov 07
Philips Semiconductors
Product specification
Single pole double throw (SPDT) switch
DESCRIPTION
SA630
PIN CONFIGURATION
The SA630 is a wideband RF switch fabricated in BiCMOS technology and incorporating on-chip CMOS/TTL compatible drivers. Its
primary function is to switch signals in the frequency range DC 1GHz from one 50Ω channel to another. The switch is activated by
a CMOS/TTL compatible signal applied to the enable channel 1 pin
(ENCH1).
D and N Packages
The extremely low current consumption makes the SA630 ideal for
portable applications. The excellent isolation and low loss makes
this a suitable replacement for PIN diodes.
VDD
1
8
OUT1
GND
2
7
AC GND
INPUT
3
6
GND
ENCH1
4
5
OUT2
SR00578
Figure 1. Pin Configuration
The SA630 is available in an 8-pin dual in-line plastic package and
an 8-pin SO (surface mounted miniature) package.
•Low distortion (IP3 intercept +33dBm)
•Good 50Ω match (return loss 18dB at 400MHz)
•Full ESD protection
•Bidirectional operation
FEATURES
•Wideband (DC - 1GHz)
•Low through loss (1dB typical at 200MHz)
•Unused input is terminated internally in 50Ω
•Excellent overload capability (1dB gain compression point +18dBm
APPLICATIONS
•Digital transceiver front-end switch
•Antenna switch
•Filter selection
•Video switch
•FSK transmitter
at 300MHz)
•Low DC power (170µA from 5V supply)
•Fast switching (20ns typical)
•Good isolation (off channel isolation 60dB at 100MHz)
ORDERING INFORMATION
TEMPERATURE RANGE
ORDER CODE
DWG #
8-Pin Plastic Dual In-Line Package (DIP)
DESCRIPTION
-40 to +85°C
SA630N
SOT97-1
8-Pin Plastic Small Outline (SO) package (Surface-mount)
-40 to +85°C
SA630D
SOT96-1
BLOCK DIAGRAM
OUTPUT/INPUT
INPUT/OUTPUT
OUTPUT/INPUT
ENCH1
SR00579
Figure 2. Block Diagram
RECOMMENDED OPERATING CONDITIONS
SYMBOL
RATING
UNITS
Supply voltage
3.0 to 5.5V
V
TA
Operating ambient temperature range
SA Grade
-40 to +85
°C
TJ
Operating junction temperature range
SA Grade
-40 to +105
°C
VDD
1997 Nov 07
PARAMETER
2
853-1577 18666
Philips Semiconductors
Product specification
Single pole double throw (SPDT) switch
SA630
EQUIVALENT CIRCUIT
VDD
1
+5V
8
OUT1
20kΩ
CONTROL
LOGIC
50Ω
7
2
AC BYPASS
50Ω
6
3
INPUT
20kΩ
4
ENCH1
OUT2
5
SR00580
Figure 3. Equivalent Circuit
ABSOLUTE MAXIMUM RATINGS
SYMBOL
PARAMETER
VDD
Supply voltage
PD
Power dissipation, TA = 25oC (still air)1
8-Pin Plastic DIP
8-Pin Plastic SO
RATING
UNITS
-0.5 to +5.5
V
1160
780
mW
mW
TJMAX
Maximum operating junction temperature
150
°C
PMAX
Maximum power input/output
+20
dBm
TSTG
Storage temperature range
-65 to +150
°C
NOTES:
1. Maximum dissipation is determined by the operating ambient temperature and the thermal resistance, θJA:
8-Pin DIP: θJA = 108°C/W
8-Pin SO: θJA = 158°C/W
DC ELECTRICAL CHARACTERISTICS
VDD = +5V, TA = 25°C; unless otherwise stated.
LIMITS
SYMBOL
IDD
PARAMETER
TEST CONDITIONS
Supply current
voltage1
SA630
UNITS
MIN
TYP
MAX
40
170
300
µA
1.1
1.25
VT
TTL/CMOS logic threshold
1.4
V
VIH
Logic 1 level
Enable channel 1
2.0
VDD
V
VIL
Logic 0 level
Enable channel 2
-0.3
0.8
V
IIL
ENCH1 input current
ENCH1 = 0.4V
-1
0
1
µA
IIH
ENCH1 input current
ENCH1 = 2.4V
-1
0
1
µA
NOTE:
1. The ENCH1 input must be connected to a valid Logic Level for proper operation of the SA630.
1997 Nov 07
3
Philips Semiconductors
Product specification
Single pole double throw (SPDT) switch
SA630
AC ELECTRICAL CHARACTERISTICS1 - D PACKAGE
VDD = +5V, TA = 25°C; unless otherwise stated.
LIMITS
SYMBOL
PARAMETER
TEST CONDITIONS
SA630
MIN
DC - 100MHz
500MHz
900MHz
S21, S12
Insertion loss (ON channel)
S21, S12
Isolation (OFF channel)2
10MHz
100MHz
500MHz
900MHz
S11, S22
S11, S22
tD
tr, tf
1
1.4
2
2.8
dB
dB
Return loss (ON channel)
DC - 400MHz
900MHz
20
12
dB
Return loss (OFF channel)
DC - 400MHz
900MHz
17
13
dB
50% TTL to 90/10% RF
20
ns
90%/10% to 10%/90% RF
5
ns
165
mVP-P
Switching speeds (on-off rise/fall time)
24
Switching transients
P-1dB
MAX
80
60
50
30
Switching speed (on-off delay)
70
UNITS
TYP
DC - 1GHz
+18
dBm
IP3
Third-order intermodulation intercept
100MHz
+33
dBm
IP2
Second-order intermodulation intercept
100MHz
+52
dBm
Noise figure (ZO = 50Ω )
100MHz
900MHz
1.0
2.0
dB
NF
1dB gain compression
NOTE:
1. All measurements include the effects of the D package SA630 Evaluation Board (see Figure 4B). Measurement system impedance is 50Ω.
2. The placement of the AC bypass capacitor is critical to achieve these specifications. See the applications section for more details.
AC ELECTRICAL CHARACTERISTICS1 - N PACKAGE
VDD = +5V, TA = 25°C; all other characteristics similar to the D-Package, unless otherwise stated.
LIMITS
SYMBOL
PARAMETER
TEST CONDITIONS
SA630
MIN
DC - 100MHz
500MHz
900MHz
S21, S12
Insertion loss (ON channel)
S21, S12
Isolation (OFF channel)
10MHz
100MHz
500MHz
900MHz
NF
Noise figure (ZO = 50Ω )
100MHz
900MHz
58
TYP
UNITS
MAX
1
1.4
2.5
dB
68
50
37
15
dB
1.0
2.5
dB
NOTE:
1. All measurements include the effects of the N package SA630 Evaluation Board (see Figure 4C). Measurement system impedance is 50Ω.
should be placed straight down as close to the device as practical.
For better isolation between the two channels at higher frequencies,
it is also advisable to run the two output/input traces at an angle.
This also minimizes any inductive coupling between the two traces.
The power supply bypass capacitor should be placed close to the
device. Figure 10 shows the frequency response of the SA630.
The loss matching between the two channels is excellent to 1.2GHz
as shown in Figure 13.
APPLICATIONS
The typical applications schematic and printed circuit board layout of
the SA630 evaluation board is shown in Figure 4. The layout of the
board is simple, but a few cautions need to be observed. The input
and output traces should be 50Ω. The placement of the AC bypass
capacitor is extremely critical if a symmetric isolation between the
two channels is desired. The trace from Pin 7 should be drawn back
towards the package and then be routed downwards. The capacitor
1997 Nov 07
4
Philips Semiconductors
Product specification
Single pole double throw (SPDT) switch
SA630
VDD
+5V
D and N Packages
0.1µF
0.01µF
1
GND
INPUT
0.01µF
8
2
7
3
6
4
5
OUT1
AC GND
0.01µF
GND
OUT2
0.01µF
ENCH1
a. Evaluation Board Schematic
b. 630 D-Package Board Layout
630N1 7/91
c. 630 N-Package Board Layout
Figure 4. Board and Package Graphics
1997 Nov 07
5
SR00581
Philips Semiconductors
Product specification
Single pole double throw (SPDT) switch
SA630
shown in Figure 8. The cascaded configuration will have a higher
loss but greater than 35dB of isolation at 1GHz and greater than
65dB @ 500MHz can be obtained from this configuration. By
modifying the enable control, an RF multiplexer/ de-multiplexer or
antenna selector can be constructed. The simplicity of SA630
coupled with its ease of use and high performance lends itself to
many innovative applications.
The isolation and matching of the two channels over frequency is
shown in Figures 15 and 17, respectively.
The SA630 is a very versatile part and can be used in many
applications. Figure 5 shows a block diagram of a typical Digital RF
transceiver front-end. In this application the SA630 replaces the
duplexer which is typically very bulky and lossy. Due to the low
power consumption of the device, it is ideally suited for handheld
applications such as in CT2 cordless telephones. The SA630 can
also be used to generate Amplitude Shift Keying (ASK) or On-Off
Keying (OOK) and Frequency Shift Keying (FSK) signals for digital
RF communications systems. Block diagrams for these applications
are shown in Figures 6 and 7, respectively.
The SA630 switch terminates the OFF channel in 50Ω. The 50Ω
resistor is internal and is in series with the external AC bypass
capacitor. Matching to impedances other than 50Ω can be achieved
by adding a resistor in series with the AC bypass capacitor (e.g.,
25Ω additional to match to a 75Ω environment).
For applications that require a higher isolation at 1GHz than
obtained from a single SA630, several SA630s can be cascaded as
5200
602A
630
IF OUT
KEYPAD
&
DISPLAY
MICRO
CONTROLLER
Tx/Rx
5200
VCO
MODULATION
SR00582
Figure 5. A Typical TDMA/Digital RF Transceiver System Front-End
ASK OUTPUT
OUT1/IN1
630
630
OSCILLATOR
ENABLE
CH1
IN/OUT
50Ω
630
TTL DATA
SR00583
630
Figure 6. Amplitude Shift Keying (ASK) Generator
OUT2/IN2
f1
FSK OUTPUT
ENABLE
Figure 8.
630
ENABLE
CH1
f2
TTL DATA
SR00584
Figure 7. Frequency Shift Keying (FSK) Gnerator
1997 Nov 07
6
SR00585
Philips Semiconductors
Product specification
Single pole double throw (SPDT) switch
SA630
200
+85°C
5V
180
+25°C
4V
-40°C
140
120
3V
S21 (dB)
SUPPLY CURRENT ( µ A)
160
–1
100
80
60
40
20
TA = +25°C
–2
0
3
3.5
4
4.5
5
5.5
10
6
100
FREQUENCY (MHz)
SUPPLY VOLTAGE (V)
1000
SR00588
SR00586
Figure 11. Loss vs. Frequency and VDD for
D-Package-Expanded Detail-
Figure 9. Supply Current vs. VDD and Temperature
0
0
5V
–2
4V
–2
–4
S21 (dB)
S21 (dB)
3V
–4
–6
–6
CH2
–8
VDD = 5V
TA = +25°C
TA = +25°C
–10
–8
10
100
1000
10
2000
FREQUENCY (MHz)
1997 Nov 07
1000
2000
SR00589
SR00587
Figure 10.
100
FREQUENCY (MHz)
Figure 12.
Loss vs. Frequency and VDD for D-Package
7
Loss Matching vs. Frequency for N-Package (DIP)
Philips Semiconductors
Product specification
Single pole double throw (SPDT) switch
SA630
0
0
–1
–10
–2
–20
–30
–4
S21 (dB)
S21 (dB)
–3
–40
3V
–5
4V
–50
CH1
–6
5V
–60
–7
VDD =
T
5V
A = +25°C
–70
TA = +25°C
–8
10
100
1000
2000
–80
10
FREQUENCY (MHz)
100
SR00590
Figure 13. Loss Matching vs. Frequency; CH1 vs. CH2 for
D-Pakage
2000
SR00592
Figure 15. Isolation vs. Frequency and VDD for D-Package
0
0
-40°C
–10
–1
+25°C
–20
–2
+85°C
–30
S21 (dB)
–3
S21 (dB)
1000
FREQUENCY (MHz)
–4
–40
CH2
–5
–50
–6
–60
–70
–7
TA = +25°C
VDD = 5V
VDD = 5V
–80
–8
10
100
1000
10
2000
100
1000
2000
FREQUENCY (MHz)
FREQUENCY (MHz)
SR00593
SR00591
Figure 14.
1997 Nov 07
Figure 16. Isolation Matching vs. Frequency for N-Package
(DIP)
Loss vs. Frequency and Temperature for
D-Package
8
Philips Semiconductors
Product specification
Single pole double throw (SPDT) switch
SA630
0
0
–10
–5
–20
–10
S22 (dB)
S21 (dB)
–30
–40
–15
CH2
–50
–20
CH1
–60
–25
VDD = 5V
–70
TA = +25°C
VDD = +5V
TA = +25°C
–80
10
100
–30
1000
10
2000
100
1000
2000
FREQUENCY (MHz)
FREQUENCY (MHz)
SR00597
SR00594
Figure 19. Output Match On-Channel vs. Frequency
Figure 17. Isolation Matching vs. Frequency; CH1 vs. CH2 for
D-Package
0
0
–5
–5
–10
–10
–15
S22 (dB)
S11 (dB)
CH1: 3V
3V
–15
CH1: 5V
4V
CH2: 5V
–20
–20
5V
–25
–25
TA = +25°C
TA = +25°C
–30
10
100
1000
–30
2000
10
FREQUENCY (MHz)
SR00595
1000
2000
SR00597
Figure 18. Input Match On-Channel vs. Frequency and VDD
1997 Nov 07
100
FREQUENCY (MHz)
Figure 20. OFF-Channel Match vs. Frequency and VDD
9
Philips Semiconductors
Product specification
Single pole double throw (SPDT) switch
SA630
0
60
–5
50
IP2
INTERCEPT POINT (dBm)
S22 (dB)
–10
+85°C
–15
+25°C
–20
40
30
IP3
20
-40°C
–25
10
VDD = 5V
TA = +25°C
–30
0
10
100
1000
2000
3
3.5
FREQUENCY (MHz)
4
4.5
5
SUPPLY VOLTAGE (V)
5.5
SR00633
SR00598
Figure 21.
Figure 23.
OFF Channel Match vs. Frequency and
Temperature
Intercept Points vs.VDD
5
20
18
4.5
5V
TA = +25°C
4
16
ZO = 50Ω
4V
3.5
14
NOISE FIGURE (dB)
3V
12
P-1 (dBm)
6
10
8
3
2.5
2
6
1.5
4
1
2
0.5
3V
4V
5V
TA = +25°C
0
0
10
100
1000
10
2000
1997 Nov 07
1000
2000
SR00634
SR00599
Figure 22.
100
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 24. Noise Figure vs. Frequency and VDD for D-Package
P-1 dB vs. Frequency and VDD
10
Philips Semiconductors
Product specification
Single pole double throw (SPDT) switch
SA630
ENCH1 (Pin4)
OUT1 (Pin 8)
SR00635
Figure 25.
1997 Nov 07
Switching Speed; fIN = 100MHz at -6dBm, VDD = 5V
11
Philips Semiconductors
Product specification
Single pole double throw (SPDT) switch
SO8: plastic small outline package; 8 leads; body width 3.9mm
1997 Nov 07
12
SA630
SOT96-1
Philips Semiconductors
Product specification
Single pole double throw (SPDT) switch
DIP8: plastic dual in-line package; 8 leads (300 mil)
1997 Nov 07
SA630
SOT97-1
13
Philips Semiconductors
Product specification
Single pole double throw (SPDT) switch
SA630
DEFINITIONS
Data Sheet Identification
Product Status
Definition
Objective Specification
Formative or in Design
This data sheet contains the design target or goal specifications for product development. Specifications
may change in any manner without notice.
Preliminary Specification
Preproduction Product
This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips
Semiconductors reserves the right to make changes at any time without notice in order to improve design
and supply the best possible product.
Product Specification
Full Production
This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes
at any time without notice, in order to improve design and supply the best possible product.
Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products,
including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips
Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright,
or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask
work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes
only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing
or modification.
LIFE SUPPORT APPLICATIONS
Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices,
or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected
to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips
Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully
indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale.
 Copyright Philips Electronics North America Corporation 1997
All rights reserved. Printed in U.S.A.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381
1997 Nov 07
14