SBT01 1W DC-DC Unregulated Single Output Converter series Features : 1000VDC I/O isolation Internal SMD technology Protection: Short circuit Cooling by free air convection Non-conductive plastic case SMD package styles 100% full load burn-in test Low cost / High reliability Approved: UL / CUL 1 year warranty SPECIFICATION ORDER NO. OUTPUT SBT01L-05 SBT01L-09 SBT01M-05 SBT01M-09 9V DC OUTPUT VOLTAGE 5V OUTPUT CURRENT RANGE 0 ~ 200mA EFFICIENCY 70% RATED POWER 1W SBT01L-12 SBT01M-12 12V 0 ~ 111mA SBT01L-15 SBT01M-15 15V 0 ~ 84mA 0 ~ 67mA 74% 75% 74% 75% 75% 75% 10.8 ~ 13.2V 12V 4.5 ~ 5.5V 5V 10.8 ~ 13.2V 12V 4.5 ~ 5.5V 5V 10.8 ~ 13.2V 12V 4.5 ~ 5.5V 5V 10.8 ~ 13.2V 12V 120mA 292mA 120mA 292mA 120mA 292mA 120mA 15mA 29mA 15mA 29mA 15mA 29mA 15mA 72% RIPPLE & NOISE (max.) Note.2 100mVp-p LINE REGULATION Note.3 1.2% for 1% input variation LOAD REGULATION Note.4 8.0% VOLTAGE TOLERANCE 8.0% SWITCHING FREQUENCY(Typ.) 100KHz 4.5 ~ 5.5V 5V VOLTAGE RANGE NORMAL VOLTAGE Full load 292mA No load 29mA INPUT CURRENT Fuse recommended PROTECTION Momentary OVERLOAD Protection type : Broken Momentary PROTECTION SHORT CIRCUIT Protection type : Broken WORKING TEMP. -40 ~ +85 WORKING HUMIDITY 20% ~ 90% RH non-condensing ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS SAFETY & WITHSTAND VOLTAGE EMC ISOLATION RESISTANCE MTBF OTHERS DIMENSION -40 ~ +105 I/P-O/P:1KVDC I/P-O/P: 100M Ohms / 500VDC / 25 Unit: mm (inch) 12.7 7.62 1 2.54 2 3 6.00 TOP VIEW 4.13 5 6.25 7.50 11.2 MAX 6 / 70% RH 500khrs min. MIL-HDBK-217F(25 ) 12.7*7.5*6.0mm or 0.50"*0.30"*0.24" inch (L*W*H) Mechanical Specification 7 , 10 ~ 95% RH 0.03% / (0 ~ 50 ) 10 ~ 500Hz, 2G 10min./1 cycle, period for 60min. each along X, Y, Z axes UL60950-1, CSA C22.2 1.3g WEIGHT 8 (Refer to output load derating curve) 2.54 4 0.5 0.25 Derating Curve Pin Configuration Pin No. Output 1 2 3 4 5 6 7 8 -Vin +Vin NC -Vout +Vout NC NC NC 100 LOAD (%) INPUT 80 -40 NOTE 0 25 50 70 85 100 Ta ( ) 1.All parameters are specified at normal input, rated load, 25 70% RH ambient. 2.Ripple & noise are measured at 20MHz by using a 12" twisted pair terminated with a 0.1uf & 47uf capacitor. 3.Line regulation is measured from low line to high line at rated load. 4.Load regulation is measured from 20% to 100% rated load. File Name: SBT01-SPEC 2008-05-08