SC339 Ultra Low Output Voltage Linear FET Controller POWER MANAGEMENT Features Description The SC339 is an ultra-low output voltage, linear power supply controller designed to simplify power management for notebook PCs. It is part of Semtech’s Smart LDO TM family of products. The SC339 has a user adjustable output that can be set anywhere between 0.5V and 3.3V using two external resistors. ± 1% Voltage Accuracy Over-Temperature Low Shutdown Current Runs Off 5V Supply Ultra-Fast Transient Response Enable Control for the Output Power Good Monitoring and Signaling for the Output Gate Drive from Input Supply Enables Use of N-Channel MOSFET User Selectable Dropout Voltage Under-Voltage Protection for the Output SOT-23 6-pin Surface Mount Package Compatible with Ceramic Capacitors Low Ripple Output Internal 1ms soft-start requires no external components Fully WEEE and RoHS compliant SC339 features include tight output voltage regulation (± 1% over 0°C to +85°C), enable control, open drain power good signal, under-voltage protection and soft-start. The enable pin allows the part to enter a very low power standby mode. Pulling it high enables the output. The power good pin is an open drain and asserts low when the voltage at the adjust pin is below 88% (typ) of nominal. If the voltage at the adjust pin is below 50% (typ) of nominal, the undervoltage protection circuitry will shut down the output. The SC339 is available in a tiny SOT-23 6-pin surface mount package. Applications Notebook PCs Desktop Computers Battery Powered Devices Portable Instruments Typical Application Circuit 1.2V +/-5% IN IRF7311 or similar C1 Vout = (1+R1/R2)*0.5 1.05V @ 3A C2 5V IN R1 IN DRV GND SC339 ADJ 1.05V Enable EN 1.05V Power Good PGD R3 (1) C4 R2 Notes: (1) Optional Components to use with ceramic output capacitors (C2) Sept 11, 2006 1 C3 (1) www.semtech.com SC339 PRELIMINARY POWER MANAGEMENT Absolute Maximum Ratings Exceeding the specifications below may result in permanent damage to the device or device malfunction. Operation outside of the parameters specified in the Electrical Characteristics section is not implied. Exposure to absolute maximum rated conditions for extended periods of time may affect device reliability. Parameter Symbol Maximum Units VIN -0.3 to +6 V VDRV -0.3 to VIN + 0.3V V VADJ, VPGD -0.3 to VIN + 0.3V V Enable Pin VEN -0.3 to VIN + 0.3V V Thermal Impedance Junction to Ambient θJA 190 °C/W Thermal Impedance Junction to Case θJC 81 °C/W Operating Ambient Temperature Range TA -40 to +85 °C Operating Junction Temperature Range TJ -40 to +125 °C Storage Temperature Range TSTG -65 to +150 °C Lead Temperature (Soldering) 10 Sec. TLEAD 300 °C ESD Rating (Human Body Model) VESD 2 kV Input Supply Voltage Drive Pin Adjust and Power Good Pin Electrical Characteristics Unless specified: TA = 25°C, VIN = VEN = 5V ± 5%, VPWR(1) = 1.5V ± 5%, 0A ≤ IOUT ≤ 3A. Values in bold apply over full operating ambient temperature range. Parameter Symbol Conditions Min Typ Max Units 4.5 5 5.5 V Supply Voltage VIN Quiescent Current IQ VIN = 5V 130 200 μA IQ(OFF) EN low 0.1 1.0 μA Start Threshold VUVLO VIN rising 4.20 V Hysteresis VHYST VIN falling 0.10 V VIH Output on VIL Output off Standby Current Input Under-Voltage Lockout EN Enable Input Threshold Enable Input Bias Current © 2006 Semtech Corp. 2.8 V VIN = VEN = 5V 2 1.8 -1 +1 μA www.semtech.com SC339 POWER MANAGEMENT Electrical Characteristics Parameter Symbol Conditions Min Typ Max Units Adjust Input Bias Current IADJ VADJ = 0.5V -100 0 +100 nA Reference Voltage VADJ 0°C ≤ TA ≤ +85°C -1% 0.500 1% V Sourcing 5 20 mA Sinking 5 20 mA VDRV Full On, IDRV = 0mA, VIN = 5V 4.70 4.85 V VTH(UV) Measured at ADJ pin 40 50 60 %VADJ Power Good Threshold(3) VTH(PGD) Measured at ADJ pin -15 -12 -8 %VADJ Output Logic Low Voltage VPGD VADJ = 0.4V, IPGD = -1mA 0.4 V Power Good Leakage Current IPGD VADJ = 0.5V, 0V ≤ VPGD ≤ VIN -1 0 +1 μA tr From EN rising to 99% of VOUT 500 1000 2000 μs ADJ DRV Output Current IDRV Output Voltage Output Under-Voltage Protection Trip Threshold(2) PGD Soft-Start Output Rise Time 10% VOUT to 90% VOUT, VOUT = 1.05V Notes: 1) VPWR = input voltage to pass device drain (or source depending upon orientation of FET). 2) If V TH(UV) is exceeded for longer than 1ms (nom.) the protection circuitry will shut down the output. 3) During start-up only, V TH(PGD) is -6% (typical), then switches to -12% (typical). © 2006 Semtech Corp. 3 www.semtech.com SC339 PRELIMINARY POWER MANAGEMENT Pin Configuration Ordering Information Top View Part Number IN 1 6 DRV SC339SKTRT GND 2 5 ADJ SC339EVB EN 3 4 PGD Package SOT-23 6 Pin Evaluation Board Notes: 1) Only available in tape and reel packaging. A reel contains 2500 devices. 2) VIN = 5V 3) VADJ is ± 1% over 0°C ≤ TA ≤ +85°C. 4) Lead-free product. This product is fully WEEE and RoHS compliant. (SOT-23 6L) Marking Information Marking for SOT23, 6 lead package: yyww = Datecode (Example: E652) Pin Descriptions Pin Pin Name 1 IN 2 GND 3 EN 4 PGD Power good signal output for VOUT 5 ADJ Regulator sense input - used for sensing the output voltage for power good and under-voltage and to set the output voltage 6 DRV © 2006 Semtech Corp. Pin Function 5V supply Ground Active high enable control - connect to IN if not being used - do not allow to float Output of regulator - drives the gate of an N-channel MOSFET to maintain VOUT set by R1 and R2 4 www.semtech.com SC339 POWER MANAGEMENT Block Diagram IN EN 0.5V Bandgap Reference Shutdown Control Vref ( 0.5V) DRV + - + Under Voltage Control Vref Error Amplifier ADJ 0.5 VBG Undervoltage Comparator PGD + 0.88 VBG (0.95 VBG At start-up) Power Good Comparator © 2006 Semtech Corp. 5 GND www.semtech.com SC339 PRELIMINARY POWER MANAGEMENT Applications Information Theory Of Operation stabilize. The power-up is very smooth and monotonic. The SC339 linear FET controller provides a simple way to drive an N-channel MOSFET to produce tightly regulated output voltages from an available, higher, supply voltage. It takes its power from the 5V system supply, drawing 130μA (typ) while operating. OCP and Power Supply Sequencing It contains an internal bandgap reference which is compared to the output voltage via a resistor divider. The resistor divider is external and user selectable. The drive pin (DRV) can pull up to a guaranteed minimum of 4.7V. Thus, the device can be used to regulate a large range of output voltages by careful selection of the external MOSFETs (see Component Selection on this page). The SC339 includes an active high enable control (EN). If this pin is pulled low, the drive pin is pulled low, turning off the N-channel MOSFET. If the pin is pulled up to 2.8V ≤ VEN ≤ VIN, the drive pin is enabled. This pin should not be allowed to float. The SC339 has a power good output (PGD) which is an open drain output that pulls low if the related output is below the power good threshold (-12% of the programmed output voltage typical). The power good circuitry is active if the device is enabled, regardless of the state of the over-current latch. An over-current protection circuit monitors the output voltage. If the output voltage drops below 50% (typical) of nominal, as would occur during an over-current or short condition, the device will pull the drive pin low and latch off. Toggle the power supply or enable pin to reset the latch condition. Drive Output The drive output is source and sink capable. The drivers both source and sink 20mA of current typically at 5V IN. Soft-Start and Power Good Timing At start-up, the internal reference is switched from its normal 0.5VDC to a 1ms (typical) linear ramp. The output voltage tracks the ramp until 0.5V is reached. The PWRGD signal is held low until the output has been in regulation approximately 500μsec to allow the output voltage to © 2006 Semtech Corp. The SC339 has output under-voltage protection that looks at the output to see if it is: a) less than 50% (typical) of its nominal value and, b) VDRV for that output is within 350mV (typical) of maximum. If both of these criteria are met, there is a 1ms (typical) delay and then the output is shut down. This provides inherent immunity to UV shutdown at start-up (which may occur while the output capacitors are being charged). At star t-up, it is necessar y to ensure the power supplies and enable are sequenced correctly to avoid erroneous latch-off. For UV latch-off not to occur at start-up due to sequencing issues, the voltage supplied to the MOSFET drain should be greater than the output under-voltage threshold when that output is enabled. This assumes that the drop through the pass MOSFET is negligible. If not, then this drop needs to be taken into account also since: VOUT = VDRAIN - (IOUT x RDS(ON)) If the supply to the SC339 IN pin comes up before the supply to the MOSFET drain, then that output should be enabled after the supply to the MOSFET drain is applied - the power good signal for this rail would be ideal. If the power supply to the MOSFET drain comes up before the power supply to the SC339 IN pin, then the output can either be enabled with the supply to the IN pin or afterwards. Please note the following example: SC339 powered from 5V, the MOSFET (VDRAIN) powered from 1.8V, set for 1.5VOUT. Worst-case: under-voltage threshold is 60% (over temperature) of 1.5V, or 0.9V. The typical enable threshold is ~2.4V, see Figure 1 on Page 7. Component Selection Output Capacitors: low ESR capacitors such as Sanyo POSCAPs or Panasonic SP-caps are recommended for bulk capacitance, with ceramic bypass capacitors for decoupling high frequency transients. Ceramic output capacitors may be used; however, use of ceramic output capacitors requires compensation on the DRV output. 6 www.semtech.com SC339 POWER MANAGEMENT Applications Information (Cont.) Input Capacitors: placement of low ESR capacitors such as Sanyo POSCAPs or Panasonic SP-caps at the input to the MOSFET (VDRAIN) will help to hold up the power supply during fast load changes, thus improving overall transient response. If VDRAIN is located at the bulk capacitors for the upstream voltage regulator, additional capacitance may not be required. In this case a 0.1μF ceramic capacitor will suffice. The 5V bias supply to the SC339 should be bypassed with a 0.1μF ceramic capacitor. Note: RDS(ON) must be met at all temperatures and at the minimum VGS condition. Setting The Output Voltage: the adjust pin connects directly to the inverting input of the error amplifier, and the output voltage is set using external resistors (please refer to the Typical Application Circuit on Page 1). Using output 1 as an example, the output voltage can be calculated as follows: MOSFETs: ver y low or low threshold N-channel MOSFETs are required. Select FETs rated for V GS of 2.7V or lower. For the device to work under all operating conditions, a maximum RDS(ON) must be met to ensure that the output will never go into dropout: R1 VOUT = 0.5 • ( 1 + —— ) R2 The input bias current for the adjust pin is so low that it can be safely ignored. To avoid picking up noise, it is recommended that the total resistance of the feedback chain be less than 100kΩ. With ceramic capacitors, a recommended divider current of >100μA is recommended to keep the FET conducting during light load conditions to improve transient response. VIN(MIN) ― VOUT(MAX) RDSON(MAX) = ——————— Ω IOUT(MAX) 2.8V SC339 Supply Comes Up Before MOSFET Drain Supply 2.7V MOSFET Drain Supply Comes Up Before SC339 Supply Power Supply Sequencing © 2006 Semtech Corp. 7 www.semtech.com SC339 PRELIMINARY POWER MANAGEMENT Applications Information (Cont.) Table 1 lists recommended resistor values for some standard output voltages. All resistors are 1%, 1/10W. Total DC error = ±2.25% = 23.6mV This leaves ±2.75% = 28.875mV for the load transient ESR spike, therefore: The maximum output voltage that can be obtained from each output is determined by the input supply voltage and the RDS(ON) and gate threshold voltage of the external MOSFET. Assuming that the MOSFET gate threshold voltage is sufficiently low for the output voltage chosen and the worst-case drive voltage, VOUT(MAX) is given by: 28.875mV RESR(MAX) = —————— = 11.55mΩ 2.5A Bulk capacitance required is given by: VOUT (MAX) = VDRAIN(MIN) ― IOUT(MAX) • RDSON(MAX) VOUT (V) R1 or R3 (kΩ) R2 or R4 (kΩ) 1.05 11.0 10.0 1.2 14.0 10.0 1.5 20.0 10.0 2.5 45.3 11.3 3.3 63.4 11.3 dl • τ CBULK(MIN) = ——— = μF dV Where dI is the maximum load current step, t is the maximum regulator response time and dV is the allowable voltage droop. Therefore with dI = 2.5A, t = 1μs, and dV = 28.875mV: 6 2.5 • 1 • 10¯ CBULK(MIN) = ———————— = 87μF 3 28.875 • 10¯ Recommended Resistor Values For SC339 Design Example So if we use 1% VOUT set resistors we would select 100μF, 12mΩ POSCAP for output capacitance (which assumes that local ceramic bypass capacitors will absorb the balance of the (12 - 11.55)mΩ ESR requirement - otherwise 10mΩ capacitors should be used). If we use 0.1% set resistors, then the total DC error becomes ±1.35% = ±15.75mV, leaving ±3.65% = 38.33mV for the ESR spike. In this case: Goal: 1.05V±5% @ up to 2.5A from 1.2V±5% and 5V±5% Solution 1: No Passive Droop Total window for DC error, ripple and transient is ±52.5mV. Since this device is linear and assuming that it has been designed to not ever enter dropout, there is negligible ripple on the output. 38.33mV = 15.33mΩ RESR(MAX) = ———— 2.5A The DC error for this output is the sum of: and, 6 2.5 • 1 • 10¯ = 65μF CBULK(MIN) = ——————— 3 38.33 • 10¯ VADJ accuracy = ±1% = ±10.5mV Feedback chain tolerance = ±1% = ±10.5mV So for 0.1% resistors we could use 1 x 100μF, 15mΩ POSCAP for output capacitance. Load regulation = ±0.25% = ±2.6mV Resistors per Table 1 should be 11.0kΩ (top) and 10.0kΩ (bottom). © 2006 Semtech Corp. 8 www.semtech.com SC339 POWER MANAGEMENT Applications Information (Cont.) This is a ver y severe example, since the output voltage is so low, therefore the allowable window is ver y small. See Solution 2 for an alternate circuit. For higher output voltages the components required will be less stringent. Solution 2: Using Passive Droop 1.2V +/-5% IN C1 0.1uF RDROOP 1.075V 1.05V @ 2.5A The input capacitance needs to be large enough to stop the input supply from collapsing below -5% (i.e., the design minimum) during output load steps. If the input to the pass MOSFET is not local to the supply bulk capacitance then additional bulk capacitance may be required. C3 R1 100uF, 25mOhm POSCAP (VIN(MIN) ― VOUT ) (1.14 ― 1.05) RDSON(MAX) = —————— = —————— = 36mΩ IOUT(MAX) 2.5 MOSFET SELECTION Si5406DC NTHS5404 SOT-23 Footprint IRLMS2002 FDN337N (when Input is > 1.2V for 1.05V output) © 2006 Semtech Corp. Vgs 0.6V 0.6V Rds-on 20mΩ 25mΩ Imax 9.5A 7.2A Vgs 1V 0.7V Rds-on 30mΩ 65mΩ Imax 5.2A 2.2A EN 3 5 ADJ GND 2 6 DRV IN 1 If 1% set resistors are used, the total DC error will be ±2.25% = 24mV. Thus, at no load, the minimum output voltage will be given by: SO-8 Footprint FDS6682 IRF7456 1206 Footprint SC339 PGD Passive droop allows us to use almost the full output tolerance window for transients, therefore making the o u t p u t c a p a c i to r s e l e c t i o n s i m p l e r a n d l e s s expensive. The trade-offs are the cost of the droop resistor versus the reduction in output capacitor cost, and the reduction in headroom which impacts MOSFET selection. The top of the feedback chain connects to the input side of RDROOP, and the output is set for 1.075V. Thus at no load, VOUT will be 1.075V (or 1.05V + 2.4%) and at IOUT = 2.5A, VOUT will be 1.025V (or 1.05V - 2.4%). So a MOSFET rated for VGS = 2.7V will be required, with an RDS(ON)(MAX) (over-temperature) given by: Imax 14A 16A U1 4 10.0k VGS = (4.4 ― 1.1025) = 3.3V Rds-on 9mΩ 6.5mΩ 11.0k R2 MOSFET selection: since the input voltage to the SC339 is 5V±5%, the minimum available gate drive is: Vgs 1.7V 1.5V Q1 20mOhm VOUT(MIN_NO_LOAD) = 1.075 ― 0.024 = 1.051V This leaves 53.5mV for transient response, giving: 53.5mV RESR(MAX) = ———— = 21.4mΩ and, 2.5A 6 2.5 • 1 • 10¯ CBULK(MIN) = ——————— = 47μF 53.5 •10¯3 Instead of 2 x 100μF, 12mΩ capacitors, we can use 1 x 47μF, 15mΩ capacitor. 9 www.semtech.com SC339 PRELIMINARY POWER MANAGEMENT Applications Information (Cont.) Using Ceramic Capacitors From this response we see that the system is not stable as it has a phase margin of approximately 0 degrees. SC339 is capable of operation using an all-ceramic solution, needing only an external R-C compensation. The Typical Application schematic (R3, C3) from page 1 is reproduced here: For stable operation we introduce a low frequency pole and a zero. The low frequency pole is used to roll off the gain quicker and the zero is used to increase the bandwidth of the system. 1.2 V +/-5 % IN IRF7311 or similar C1 The Pole-Zero location: V out = (1+R1/R2)*0.5 1.05 V @ 3A C2 PHASE (deg) Gain (dB) 5 V IN R1 270 60 DRV IN Pin + Pcomp GND 1.05V Enable SC339 ADJ EN PGD 1.05 V Power Good C4 Prout Zin + Zcomp Typical Applications Circuit Gain (dB) 100 -20 Typical Frequency Response without Compensation and Ceramic Output Capacitors: Pcout 1K 10K 100K 1MEG PHASE FREQ (Hz) 10MEG -90 -40 -180 -60 -270 PHASE (deg) Low frequency pole generated internally Pin SC339 Frequency Response with Ceramic Output Capacitors and R-C Compensation 270 Low frequency zero generated internally Rout / Cout pole, moves with the load current Prout Zin 40 180 20 Pcout 100 1K 10K 100K High frequency pole generated by ESR and Output Capacitor 1MEG From the above figure we can see that the overall response of the system is stable with a decent phase margin 90 FREQ (Hz) 10MEG It is important to select the external compensation zero to be between 1 kHz and 5 kHz for optimum bandwidth and phase margin. In this example we have selected zero at approximately 3 kHz. PHASE -90 -20 -40 90 20 C 3 (1) 0,0 0,0 180 R2 Notes : (1 ) Optional Components to use with ceramic output capacitors (C2) 60 Ceramic Capacitor Operation with Compensation on DRV pin 40 R 3 (1) Ceramic Capacitor operation with very low ESR for the output capacitor . We get a three pole 1 zero system as shown above and is unstable without external compensation -60 -180 The compensation values are calculated by the following empirical equation: -270 ½• SC339 Frequency Response with Ceramic Output Capacitors and no Compensation • R3 • C3 = 3kHz We chose a low R3 compensation value to roll off gain. R3 = 100 Ω. © 2006 Semtech Corp. 10 www.semtech.com SC339 POWER MANAGEMENT Applications Information (Cont.) Now, Layout Guidelines C3 = ½ • • R3 • 3kHz = 530nF The advantages of using the SC339 to drive external MOSFETs are: We choose C3 = 470nF as the standard value. Soft-Start Behavior a) that the bandgap reference and control circuitry are in a die that does not contain high power dissipating devices At start-up, VOUT first ramps linearly from ground at the rate of ~0.5V/ms (+/- 25%) for about 800us. The linear ramping is followed by a phase of smooth settling for about 700us at the end of which the output has fully settled (to better than 1%). and, b) that the device itself does not need to be located right next to the power devices. Thus very accurate output voltages can be obtained since changes due to heating effects will be minimal. The total start-up time of about 1.5ms is kept within 1ms - 2ms window, and this is regardless of the loading and of the external components connected to the device. The 0.1μF bypass capacitor should be located close to the supply (IN) and GND pins, and connected directly to the ground plane. The feedback resistors should be located at the device, with the sense line from the output routed from the load (or top end of the droop resistor if passive droop is being used) directly to the feedback chain. If passive droop is being used, the droop resistor should be located next to the load to avoid adding additional unplanned droop. Sense and drive lines should be routed away from noisy traces or components. For very low input to output voltage differentials, the input to output/load path should be as wide and short as possible. Where greater headroom is available, wide traces may suffice. SC339 Start-Up Response Power dissipation within the device is practically negligible, thus requiring no special consideration during layout. The MOSFET pass devices should be laid out according to the manufacturer’s guidelines for the power being dissipated within them. © 2006 Semtech Corp. 11 www.semtech.com SC339 PRELIMINARY POWER MANAGEMENT Performance Characteristics Supply Current vs. Supply Voltage Adjust Voltage vs. Output Current VCC = 4.5V to 5.5V, IOUT = 2.5A, VIN = 1.5V, VEN = 5V IOUT = 0A to 3A, VIN = 1.5V, VCC = 5.0V, VEN = 5V 160.0E-6 0.5060 155.0E-6 0.5040 150.0E-6 VADJ (V) I CC (A) 0.5020 145.0E-6 140.0E-6 0.5000 135.0E-6 0.4980 130.0E-6 0.4960 125.0E-6 4.500 4.600 4.700 4.800 4.900 5.000 5.100 5.200 5.300 5.400 0.4940 0.000 5.500 VCC (V) 0.500 1.000 1.500 2.000 2.500 3.000 IOUT (A) Supply Current Adjust Voltage +1% -1% Figure 1: Supply Current v/s Supply Voltage Figure 2: Adjust Voltage v/s Output Current (1% accurate) Figure 3: Soft Start waveform shows the PWRGD delay Figure 4: Input UVLO Test (Rising) Figure 5: Input UVLO Test (Falling) © 2006 Semtech Corp. Figure 6: Enable threshold detect (Rising) 12 www.semtech.com SC339 POWER MANAGEMENT Performance Characteristics Figure 8: Transient load rising edge Figure 7: Enable threshold detect (Falling) Figure 9: Transient load falling edge © 2006 Semtech Corp. 13 www.semtech.com SC339 PRELIMINARY POWER MANAGEMENT Outline Drawing - SOT-23 6 DIMENSIONS INCHES MILLIMETERS DIM MIN NOM MAX MIN NOM MAX A e1 2X E/2 A A1 A2 b c D E1 E e e1 L L1 N 01 aaa bbb ccc D N EI 1 E 2 ccc C 2X N/2 TIPS e B D aaa C A2 SEATING PLANE bxN bbb 1.45 0.90 0.00 0.15 .90 1.15 1.30 0.25 0.50 0.22 0.08 2.80 2.90 3.00 1.50 1.60 1.75 2.80 BSC 0.95 BSC 1.90 BSC 0.30 0.45 0.60 (0.60) 6 0° 10° 0.10 0.20 0.20 A H A1 C .057 .035 .006 .000 .035 .045 .051 .020 .010 .009 .003 .110 .114 .118 .060 .063 .069 .110 BSC .037 BSC .075 BSC .012 .018 .024 (.024) 6 10° 0° .004 .008 .008 C A-B D H c GAGE PLANE 0.25 L 01 (L1) SEE DETAIL A DETAIL A SIDE VIEW NOTES: © 2006 Semtech Corp. 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. DATUMS -A- AND -B- TO BE DETERMINED AT DATUM PLANE -H- 3. DIMENSIONS "E1" AND "D" DO NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. 14 www.semtech.com SC339 POWER MANAGEMENT Land Pattern - SOT-23 6 X DIM (C) G Z Y P DIMENSIONS INCHES MILLIMETERS C G P X Y Z (.098) .055 .037 .024 .043 .141 (2.50) 1.40 0.95 0.60 1.10 3.60 NOTES: 1. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET. Contact Information Semtech Corporation Power Management Products Division 200 Flynn Road, Camarillo, CA 93012 Phone: (805) 498-2111 Fax: (805) 498-3804 www.semtech.com © 2006 Semtech Corp. 15 www.semtech.com