SD-25 25W Single Output DC-DC Converter series Features : 2:1 wide input range Protections: Short circuit / Overload / Over voltage 1500VAC I/O isolation Built-in EMI filter, low ripple noise 100% full load burn-in test Fixed switching frequency at 83KHz Low cost High reliability 2 years warranty SPECIFICATION MODEL OUTPUT SD-25A-5 SD-25B-5 SD-25C-5 SD-25A-12 SD-25B-12 SD-25C-12 SD-25A-24 DC VOLTAGE 5V 12V 24V RATED CURRENT 5A 2.1A 1.1A CURRENT RANGE 0 ~ 5A 0 ~ 2.1A 0 ~ 1.1A RATED POWER 25W 25.2W 26.4W RIPPLE & NOISE (max.) Note.2 100mVp-p VOLTAGE ADJ. RANGE 4.5 ~ 5.5VDC 120mVp-p 150mVp-p 11 ~ 16VDC 23 ~ 30VDC VOLTAGE TOLERANCE Note.3 2.0% 1.0% 1.0% LINE REGULATION 0.5% 0.3% 0.2% LOAD REGULATION 0.5% 0.3% 0.2% SD-25B-24 SD-25C-24 78% 81% SETUP, RISE, HOLD UP TIME 2.5s, 50ms, ------ at full load INPUT VOLTAGE RANGE A:9.2 ~ 18VDC EFFICIENCY (Typ.) 71% DC CURRENT 3.2A/12V OVERLOAD 105 ~ 150% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed OVER VOLTAGE 5.75 ~ 6.75V/10% load 16.8 ~ 20V/10% load Protection type : Hiccup mode, recovers automatically after fault condition is removed WORKING TEMP. -10 ~ +60 PROTECTION WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS SAFETY & WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC (Note 4) EMC EMISSION OTHERS 74% C:36 ~ 72VDC 72% 75% 78% 1.6A/24V 31.5 ~ 37.5V/10% load (Refer to "Derating Curve") 20 ~ 90% RH non-condensing -20 ~ +85 , 10 ~ 95% RH 0.03%/ (0 ~ 50 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes Design refer to LVD I/P-O/P:1.5KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 Compliance to EN55022 (CISPR22) Class B / 70% RH Compliance to EN61000-4-2,3,4,6,8, EN55024,heavy industry level, criteria A MTBF 374.3K hrs min.(SD-25A) 365.9K hrs min.(SD-25B) 99*97*36mm (L*W*H) 0.38Kg; 45pcs/17.8Kg/0.9CUFT DIMENSION 75% 0.8A/48V EMC IMMUNITY PACKING NOTE B:19 ~ 36VDC 72% 377.5K Hrs min.(SD-25C) MIL-HDBK-217F (25 ) 1. All parameters NOT specially mentioned are measured at 12,24,48VDC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. File Name:SD-25-SPEC 2011-08-23 SD-25 25W Single Output DC-DC Converter Mechanical Specification Unit:mm 36 Case No. 905 series 2 3.5 51.5 9.5 1 3 5.5 M 2- 5 20.5 55.5 8.2 3 97 4 55 3.5 4.5 89 99 6.5 3 Terminal Pin No. Assignment 3.5 74 18 Pin No. 1 2 3 36 2-M 28 3.5 17.5 7 87 Assignment DC INPUT VDC INPUT V+ FG Pin No. 4 5 Assignment DC OUTPUT +V DC OUTPUT -V Block Diagram fosc : 83KHz RECTIFIERS & FILTER EMI FILTER I/P RECTIFIERS & FILTER POWER SWITCHING FG O.L.P. +V -V DETECTION CIRCUIT PWM CONTROL O.V.P. Static Characteristics(SD-25C-24V) OUTPUT VOLTAGE (V) SD-25B,C/12,24 100 80 SD-25A SD-25B-5 SD-25C-5 LOAD (%) 60 40 20 -10 -10 0 0 10 20 30 40 50 45 AMBIENT TEMPERATURE ( ) 60 55 (VERTICAL) (HORIZONTAL) 32 350 28 300 24 250 20 200 16 150 12 100 8 50 25 30 35 40 45 50 55 60 65 70 OUTPUT RIPPLE (mVp-p) Derating Curve 72 INPUT VOLTAGE (V) File Name:SD-25-SPEC 2011-08-23