Specification : TS-S97D022C Date : August , 2000 Technical Specification for Optical Transceiver Module SDM7101-XC SDM7101-GC 155.52Mb/s 622.08Mb/s other __________ Short Haul Intermediate Reach other __________ Single 5.0 V Long Haul Long Reach Single 3.3 V 1.3 µm 1.55 µm other __________ Transmitter Receiver Transceiver ( 2R / 3R ) other __________ ( 2R / 3R ) Sumitomo Electric reserves the right to make changes in this specification without prior notice. #Safety Precaution Symbols This specification uses various picture symbols to prevent possible injury to operator or other persons or damage to properties for appropriate use of the product. The symbols and definitions are as shown below. Be sure to be familiar with these symbols before reading this specification. Warning Caution Wrong operation without following this instruction may lead to human death or serious injury. Wrong operation without following this instruction may lead to human injury or property damage. Example of picture symbols (SDM7101-XC,SDM7101-XC) indicates prohibition of actions. Action details are explained thereafter. indicatescompulsoryactionsorinstructions.Actiondetailsareexplainedthereafter. -1/9- Specification : TS-S97D022C Date : August , 2000 1. General SDM7101-XC / SDM7101-XC-W is a series of compact and high speed performance digital optical transceiver module ideally designed for versatile high speed network applications. 1300nm high speed InGaAsP FP-LD and InGaAs PIN-PD are provided as a light source and a detector, respectively. Transceiver module has PC board mountable package with electrical and optical interfaces. * Data Rate * Duty Cycle * Power Supply Voltage * Electrical Interface * Fiber Coupled Power *Sensitivity * Connector Interface 155.52Mbps,NRZ 50% Single +5.0V PECL -8 ~ -15dBm (Typ. -11dBm) for SMF ~ -34dBm (Typ. -38dBm) SC Duplex Connector The features of SDM7101-XC / SDM7101-XC-W are listed below. * Features Low Power Consumption Low Profile (9.8mm Max) Plastic Molded Package Multi-sourcedFootprint Transmitter...... Uncooled Laser with Automatic Power Control IC Class 1 Laser Product (IEC 825-1 and FDA 21 CFR 1040.10 and 1040.11) Receiver......... Wide Dynamic Range Signal Detect (FLAG) Function 2. Block Diagram Monitor Pin PD LD Automatic Power Control Modulation Current Control TD Bias Current Control Current Source LD Driver TDb Figure 1-1. Block Diagram(Transmitter ) Front-End Amplifier Peak Hold Circuit Comparator Limiting Amplifier Pin PD Figure 1-2. Block Diagram(Receiver ) (SDM7101-XC,SDM7101-XC) -2/9- Output Buffer SD RDb RD Specification : TS-S97D022C Date : August , 2000 3. Package Dimension 12.7 All dimensions are in mm. 9.4Max 25.4 0.6 20.32 0.8 2.54Px8=20.32 5.5 15.88 9.8Max 2-φ1.5 0.6 3.2 3.9 1.52 0.4 Lead pin UNIT:mm Figure2-1. Outline Dimensions ( SDM7101-XC ) Notes: 1. Surface of the receptacle and latch levers are metalized. Figure2-2. Outline Dimensions ( SDM7101-GC-ZN / SDM7101-GC-ZW ) (SDM7101-XC,SDM7101-XC) -3/9- Specification : TS-S97D022C Date : August , 2000 All dimensions are in mm. Finger Position Option ( Type-A Finger ) # L A 0 B 1 C 2 D 3 E 4 Figure2-3. Outline Dimensions ( SDM7101-GC-#N / SDM7101-GC-#W ) Figure2-4.RecommendedFootprint Caution Do not disassemble this product. Otherwise, failure, electrical shock, overheating or fire may occur. Handle the lead pins carefully. Use assisting tools or prospective aids as required. A lead pin may injure skin or human body (SDM7101-XC,SDM7101-XC) -4/9- Specification : TS-S97D022C Date : August , 2000 4. Pin Assignment No. Symbol Function 1 Veerx Power Supply (-) for Receiver : Connected to GND 2 RD Differential Data Output (Positive) 3 RDb Differential Data Output (Negative) 4 FLAG(SD) FLAG (Signal Detect) 5 Vccrx Power Supply (+) for Receiver : Connected to +5.0V 6 Vcctx Power Supply (+) for Transmitter : Connected to +5.0V 7 TDb Transmitter Differential Data (Negative) 8 TD Transmitter Differential Data (Positive) 9 Veetx Power Supply (-) for Transmitter : Connected to GND 5. Absolute Maximum Ratings Parameter Storage Case Temperature Operating Case Teperature Symbol Ts Tc Supply Voltage Input Voltage Lead Soldering (Temperature) (Time) Vcc-Vee Vi min. -40 0 -40 0.0 Vee Max 85 70 85 6.0 Vcc+0.5 260 10 Unit °C °C °C V V °C sec. Note 1 1, 2 1, 3 4 5 6 Note 1. No condensation allowed. 2. SDM7101-XC 3. SDM7101-XC-W 4. Vcc>Vee, Vcc=+5.0V, Vee=GND 5. TD, TDb 6. Measured on lead pin at 2mm (0.079in.) off the package bottom Warning Use the product with the rated voltage described in the specification. If the voltage exceeds the maximum rating, overheating or fire may occur. Caution Do not store the product in the area where temperature exceeds the maximum rating, where there is too much moisture or dampness, where there is acid gas or corrosive gas, or other extreme conditions. Otherwise, failure, overheating or fire may occur. (SDM7101-XC,SDM7101-XC) -5/9- Specification : TS-S97D022C Date : August , 2000 6. Electrical Interface ( Unless otherwise specified, VccTX-VeeTX =VccRX-VeeRX= 4.75 to 5.25 V and all operating temperature shall apply. ) 6-1.Transmitterside Parameter Supply Voltage Supply Current Input Voltage High TD, TDb Low Input Current High TD, TDb Low Signal Input Rise / Fall Time Symbol min. VccTX-VeeTX 4.75 Idtx Vih VccTX-1.17 Vil VccTX-1.95 Iih -10 Iil -10 Note 1. Input bias current is not included. 50% duty cycle data. 155.52Mbps Typ. 5.00 70 Max. 5.25 150 VccTX-0.73 VccTX-1.45 150 10 1.6 2. VccTX-VeeRX=5.0V, Tc=25°C Unit V mA V Note µA 2 nsec. 3 1 2 3. 20 ~ 80% 6-2. Receiver side Parameter Supply Voltage Supply Current Data & SD High Output Voltage Low Data Rise / Fall Time of Output Signal SD Assert Time SD Deassert Time Symbol min. VccRX-VeeRX 4.75 Idrx Voh VccRX-1.03 Vol VccRX-1.81 Trd / Tfd Sa Sd Note 1. Output current is not included. 50% duty cycle data, 155Mbps, NRZ Note 2. Vccrx=+5.0V, Tc=25°C, Output load resistance Rl=50Ω to Vccrx-2V for RD, RDb and SD. Note 3. 20 ~ 80% Note 4. Please refer to Figure 4 Note 5. 50% duty cycle data, 155Mbps, PRBS223-1, NRZ, Pin = -34 ~ -8dBm Typ. 5.00 60 Max. 5.25 110 VccRX-0.88 VccRX-1.62 1.6 100 350 Unit V mA V Note nsec µsec µsec 3 4 4 1 2 FLAG Output "H" "L" Pd Pa Optical Input Power Figure 4. FLAG Assert Level and Deassert Level 7. Optical Interface ( Unless otherwise specified, Vcc-Vee = 4.75 to 5.25 V and all operating temperature shall apply. ) 7-1.Transmitterside Parameter Average Output Power to SMF Extinction Ratio Center Wavelength Spectral Width (RMS) Eye Mask for Optical Output Symbol Pos Er λc ∆λ min. -15.0 8.2 1261 Typ. -11.0 Max. -8.0 1360 7.7 Unit dBm dB nm nm Note 1 1 Refer to Figure 5 Note 1. Measured at 155.52Mbps PRBS2^23-1, 50% duty cycle data, NRZ Normalized Amplitude 1.20 Relation between Input Signal and Optical Output Signal 1.00 Input Signal 0.80 0.50 0.20 0.00 -0.20 0.00 0.15 0.35 0.65 Optical Output Siganl TD TDb High Low ON (High) Low High OFF (Low) High High Undefined Low Low Undefined 0.85 1.00 Figure 5. Optical Pulse Mask with Fourth Order Bessel-Thomson Filter Specified in ITU-T G.957 Warning Do not look at the laser beam projection area (e.g. end of optical connector) with naked eyes or through optical equipment while the power is supplied to this product. Otherwise, your eyes may be injured. (SDM7101-XC,SDM7101-XC) -6/9- Specification : TS-S97D022C Date : August , 2000 7-2. Receiver side Parameter Center Wavelength Minimum Sensitivity Overload Flag Assert Level Flag deassert Level Symbol Pmin Pmax Pa Pd min. 1261 Typ. -8.0 -48 -49 Max. 1580 -34.0 -37 -40 Unit nm nm nm dBm dBm -34 -34 Note 1. BER=10^-10, 2. Measured at the bit rate of 155.52Mbps, PRBS 2^23-1, NRZ Note 2. 50% duty cycle data 8. Recommended Inteface Circuit TD VccTx 9. VeeTx R1 R2 Terminate close to Transceiver Inputs 8. TD C2 R3 R4 TDb 7. TDb 6. VccTx C3 5. VccRx 4. SD C4 C5 R11 Vcc L1 C1 Vcc L2 R5 SD R6 3. RDb Vcc R7 R8 2. RD RDb R9 1. VeeRx C6 R10 Terminate close to Device Inputs RD : Transmission Line with Zo= 50Ω R1 = R3 = R5 = R7 = R9 = 82Ω , R2 = R4 = R6 = R8 = R10 = 130Ω , R11=10Ω C1 = 100 µF, C3 = 2200 pF, C2 = C6 = 0.1 µF, C4 = C5 = 1 µF L1, L2 : Ferrite Bead ZBF 253D-00 (TDK) Figure 6 (SDM7101-XC,SDM7101-XC) Recommended Interface Circuit -7/9- Note 1, 2 1, 2 2 Specification : TS-S97D022C Date : August , 2000 9. Reliability Test Bellcore TA-NWT-000983 Issue 2, December 1993 Heading Test Mechanical Mechanical Integrity Shock Vibration Reference MIL-STD-883 Method 2002 MIL-STD-883 Method 2007 Thermal Shock MIL-STD-883 Method 1011 Solderability MIL-STD-883 Method 2003 Fiber Pull Endurance Accel. Aging (High Temp.) Sampling LTPD SS C SEI Plan SS F/C Condition B 5 times/axis 500G, 1.0 ms 1,500G, 0.5ms 20% 20% 11 11 0 0 --11 --0 Condition A 20 G 20% 11 0 11 0 20% 11 0 11 0 (steam aging not required) 20% 11 0 11 0 1 Kg; 3 times;5sec. 2 Kg; 3 times; 5sec. 20% 20% 11 11 0 0 ----- ----- 20-2,000 Hz 4 min/cycle; 4 cycles/axis ∆T=100°C (R)-453 Section 5.18 +85C; rated power >5,000hrs. --- 25 --- 25 0 High Temp. ---------- >10,000hrs. max. storage T (T=85°C) --20% 10 11 --0 ----- ----- Storage Low Temp. ---------- >2,000 min. storage T (T=-40°C) 20% 11 0 11 0 Section 5.20 >2,000 - 40°C to +85°C 400 times pass/fail 500 times for info. 20% --- 11 11 0 --- ----- ----- 500 times pass/fail 1000 times for info. 20% --- 11 11 0 --- 11 11 0 0 Damp Heat MIL-STD-202 M103 40°C , 95%, 56days 20% (if using epoxy) or IEC 68-2-3 or 85°C /85%RH 2,000hrs. 20% 11 11 0 0 11 --- 0 --- Cyclic Moisture Section 5.23 Resistance ---------- 20% 11 0 11 0 Internal Moisture < 5,000 ppm water vapor 20% 11 0 11 0 ------- ---6 ----- ---6 OK 0 Storage Temperature Cycling Special Tests Condition MIL-STD-883 Method 1018 Flammability TR357:Sec. 4.4.2.5 ----------ESD Threshold Section 5.22 ----------- 10. Laser Safety This product uses a semiconductor laser system and is a laser class 1 product acc. FDA, complies with 21CFR1040. 10 and 1040.11. Also this product is a laser class 1 product acc. IEC 825-1. Class 1 Laser Product Caution If this product is used under conditions not recommended in the specification or this product is used with unauthorized revision, classfication for laser product safety standard is invalid. Classify the product again at your responsibility and take appropriate actions. (SDM7101-XC,SDM7101-XC) -8/9- Specification : TS-S97D022C Date : August , 2000 11. Other Precaution Under such a strong vibration environment as in automobile, the performance and reliability are not guaranteed. The governmental approval is required to export this product to other countries. To dispose of these components, the appropriate procedure should be taken to prevent illegal exportation. This module must be handled, used and disposed of according to your company's safe working practice. Warning Be sure to carry out correct soldering for connection to peripheral circuits in order to prevent contact failure or short-circuit. Otherwise, a strong laser beam may cause eye injury, overheating or fire. Do not put this product or components of this product into your mouth. This product contaions material harmful to health. Caution Be sure to turn the power off when you touch this product connected to the printed circuit boards. Otherwise, electric shock may occur. Dispose this product or equipment including this product properly as an industrial waste according to the regulations. 12. Ordering Information Ordering Number SDM7101-XC SDM7101-XC-W Connector type SC Duplex Connector, Non-metallized. SDM7101-GC-## Operating Temparature Tc = 0 ~ 70°C Tc = -40 ~ 85°C SC Duplex Connector, Metallized. See chart below for detail. SDM7101-GC-# # Operating Case Temperature Option N : 0°C ~ -70°C W : -40°C ~ 85°C 13. For More Information EMI Shield Finger Option Z : Without Finger A ~ E : With Type-A Finger *Letter specifies finger position. Refer to Figure2-3 for detail. U.S.A. ExceLight Communications, 4021 Stirrup Creek Drive, Suite 200 Durham, NC 27703 Tel. +1-919-361-1600 / Fax. +1-919-361-1619 E-mail: [email protected] http://www.excelight.com Europe Sumitomo Electric Europe Ltd., 220, Centennial Park, Elstree, Herts, WD6 3SL, United Kingdom Tel. +44-208-953-8681 Fax. +44-208-207-5950 http://www.sumielectric.com Japan Sumitomo Electric Industries, Ltd. ( International Business Division ), 3-12, Moto-Akasaka 1-chome Minato-ku Tokyo 107-8468 Tel. +81-3-3423-5771 / Fax. +81-3-3423-5099 E-mail: [email protected] http://www.sei.co.jp/Electro-optic/index.html (SDM7101-XC,SDM7101-XC) -9/9-