SF1091A • • • • • • Designed for GSM BTS Transmitter Applications Low Insertion Loss Excellent Size-to-Performance Ratio Hermetic 13.3 X 6.5 mm Surface-Mount Case Unbalanced Input and Output Pb Complies with Directive 2002/95/EC (RoHS) 211 MHz SAW Filter Absolute Maximum Ratings Rating Value Units +10 dBm 30 VDC Maximum Incident Power in Passband Max. DC voltage between any 2 terminals Storage Temperature Range -40 to +85 Suitable for lead-free soldering - Max Soldering Profile °C SM13365-12 260°C for 30 s Electrical Characteristics Characteristic Nominal Center Frequency Passband Rejection Sym fC Insertion Loss at fc Notes 1 IL 3 dB Passband BW3 Group Delay Variation over fc ±150 kHz GDV 1, 2 fc-80 to fc-2.0 and fc+2.0 to fc+80 MHz n x fc over 291 to 2000 MHz Frequency Temperature Coefficient TA 1 FTC 1 Impedance Matching to 50 Ω unbalanced ±450 Typ 211.000 Max Units MHz 7 8.0 dB 250 nsP-P ±500 200 1, 2, 3 fc-2.0 to fc-1.05 and fc+1.05 to fc+2.0 MHz Operating Temperature Range Min 10 21 30 33 40 60 kHz dB +85 -10 0.32 °C ppm/°C2 External L-C Case Style SM13365-12 13.3 x 6.5 mm Nominal Footprint Lid Symbolization (XX = 2 character date code) RFM SF1091A XX Electrical Connections Connection Terminals Port 1 Hot 11 Port 1 Gnd Return 12 Port 2 Hot 5 Port 2 Gnd Return Case Ground 6 All others Notes: 1. Unless noted otherwise, all specitication apply over the operating temperature range with filter soldered to the specified demonstration board with impedanced matching to 50 Ω network analyzer. 2. Unless noted otherwise, all frequency specitications are referenced to the nominal center frequency, fc. 3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent oon PCB layout and external impedance matching design. See Application Note No. 42 for details. 4. The turnover temperature, TO, is the temperature of maximum (or turnover) frequency, fo. The nominal frequency at any case temperature, Tc, may 5. 6. 7. 8. be calculated from: f=fo[1-FTC(To-Tc)2]. The design, manufacturing process, and specifications of this filter are subject to change. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. Electrostatic Sensitive Device. Observe precautions for handling. RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com SF1091A-100605 Page 1 of 9 211 MHz SAW Filter RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com SF1091A-100605 Page 2 of 9 211 MHz SAW Filter SM13365-12 Case 12-Terminal Ceramic Surface-Mount Case 13.3 x 6.5 mm Nominal Footprint Case Dimensions Dimension A B C D E H P Min 13.08 6.27 Materials Max 13.60 6.80 2.00 Inches Nom 0.524 0.256 0.075 0.059 0.031 0.039 0.100 Min 0.515 0.247 Max 0.535 0.268 0.079 Electrical Connections Solder Pad Termination Au plating 30 - 60 uInches (76.2-152 uM) over 80200 uInches (203-508 uM) Ni. Lid Fe-Ni-Co Alloy Electroless Nickel Plate (8-11% Phosphorus) 100-200 uInches Thick Body mm Nom 13.31 6.50 1.91 1.50 0.79 1.0 2.54 Connection Port 1 Port 2 Al2O3 Ceramic Terminals Input or Return 2 Return or Input 3 Output or Return 8 Return or Output Pb Free 9 Ground All others Single Ended Operation Return is ground Differential Operation B 3 Return is hot C 4 D H 2 1 2 3 4 1 P (8 Places) 5 12 12 5 6 11 11 6 7 10 10 7 A 8 9 TOP VIEW RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. 9 E (10 Places) 8 BOTTOM VIEW E-mail: [email protected] http://www.rfm.com SF1091A-100605 Page 3 of 9 211 MHz SAW Filter COMPONENT ORIENTATION and DIMENSIONS 4.0 mm ±0.1 1.5 mm +0.1 -0.0 2.0 mm ±0.1 1.75 mm ±0.1 PIN #1 W (CARRIER TAPE SIZE) 11.5 mm ±0.1 ±0.1 7.5 mm BO 1.5 mm +0.3 -0.0 P (PITCH) AO USER DIRECTION OF FEED COVER TAPE SIZE 2.15 mm ±0.2 KO COVER TAPE 0.32 mm ±0.3 Carrier Tape Dimensions Ao 7.0 mm ±0.1 Bo 13.8 mm ±0.1 Ko 2.2 mm ±0.1 Pitch 12.0 mm ±0.1 W 24.0 mm ±0.3 RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com SF1091A-100605 Page 4 of 9 211 MHz SAW Filter Leader and Trailer specifications (Based upon EIA-481) Dimensions of the leader and trailer 7 Inch Reel Quantity 500 Symbol Dimension A N +0 -4 178 60 C ±1 D +0.5 -0.2 13 B +1.5 -0 20.2 2 W1 ±0.5 W2 +2 -0 24.4 30.4 MAX 13 Inch Reel Quantity 2000 Symbol Dimension A 330 N +0 -4 100 C ±2 13 D +0.5 -0.2 20.2 B +1.5 -0 2 W1 ±0.5 24.4 W2 +2 -0 30.4 MAX Dimensional drawing of the reel RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com SF1091A-100605 Page 5 of 9 211 MHz SAW Filter Additional items (1) Cover tape peeling strength The cover tape shall be adhered evenly to the carrier tape along both sides in the pulling direction. The cover tape peeling strength shall be as follows for an angle between the cover tape and the pulling direction of 165° to 180° (see the figure) and a peeling speed of 300mm/min. ±10mm/min. [EIA-481] 0.1N to 1.3N for a tape width of 12 to 56mm Fixing method 1. Insert the tip of the carrier tape into the groove. 2. Fix the tip of the cover tape with adhesive tape. Tape material (1) Carrier tape [anti-charging treatment: carbon used] Surface resistivity: 1 x 108 or less Material: Polystyrene or Polycarbonate (2) Cover tape material: Polyester (anti-charging treated) Surface resistivity: 1 x 1012 or less t = 50 to 100µm width = 13.3mm Warranty periods Cover tape peeling strength and mounting performance of stored components. 2-1. Cover tape peeling strength: One year after delivery (Peeling strength: 0.1N to 1.3N) Number of missing components There shall not be two or more consecutive missing components. Also, the maximum number of missing components shall be the larger of one piece or 0.1%. Storage environment Keep the product on which taping has been performed to a temperature below 40°C and a humidity within 80% RH. Do not subject in the direct sun. RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com SF1091A-100605 Page 6 of 9 211 MHz SAW Filter Labeling The following items are labeled on the surface of a reel. Product Part Number, Date Code, Quantity RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com SF1091A-100605 Page 7 of 9 211 MHz SAW Filter Package for Shipment 13 Inch Reel Quanity Per Reel Number Reels Per Carton External Caton Dimensions Reel Weight Shipping Carton Weight Total Weight 2000 2 356 x 356 x 102 mm 14 x 14 x 4 inches 1288 g 448 g 1736 g 2000 4 356 x 356 x 178 mm 14 x 14 x 7 inches 2576 g 448 g 3024 g 2000 8 356 x 356 x 356 mm 14 x 14 x 14 inches 5152 g 448 g 5600 g RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com SF1091A-100605 Page 8 of 9 211 MHz SAW Filter RFM Qualification and Reliability Test Test Standard Test Parameters 1 Life at Elevated Temperature MIL-STD-202 Method 108 Condition C 1,000 Hours 125°C Unbiased 2 Temperature Cycling JESD22 Method JA-104 Air-to-Air -55 ×Cto +125 ×C 20 min. Dwell 1,000 cycles 3 Vibration, Variable Frequency MIL-STD-883 Method 2007 Condition B 50g Max. 4 Cycles, 3 Axis 20 Hz to 2 kHz to 20 Hz 4 Mechanical Shock MIL-STD-883 Method 2002 Condition B 1,500g Max. 5 Shocks ±3 Axis 5 Destructive Bond Strength MIL-STD-883 Method 2011 Condition C Wire Bond Pull Strength 2.0 grams (After Seal) 6 Die Shear Strength MIL-STD-883 Method 2019 Shear Strength 0.6 kg (Strength/area limit in development) 7 Solderability (Note 2) J-STD-002 Method B 8 hr. steam age 245 × C solder temperature 5 second dwell >95% wetted surface 8 Physical Dimensions JESD22 Method JB-100 Critical Dimensions Within specifications 9 Temperature Characteristics RFM Procedure Frequency over Temperature Within specifications 10 Terminal Strength (Note 2) MIL-STD-833 Method 2004 Condition A & D Cond. A-Lead Tension Cond. B -Pad Adhesionr 24 8 oz. - 30 sec. Visual Requirements & meets Hermetic Spec. 11 Resistance to Solvents MIL-STD-883 Method 2015 Solvents a, b, d Visual Requirements 12 Steady State Life MIL-STD-883 Method 1005 1,000 Hours Max. Operating Temperature Rated Voltage Within Electrical & Hermetic Spec. (Note 1) 13 Internal WaterVapor Content MIL-STD-883 Method 1018 < 5,001 PPM 14 Constant Acceleration MIL-STD-883 Method 2001 Y1 Direction 30,000g Within Electrical & Hermetic Spec. (Note 1) 15 Substrate Attach Strength MIL-STD-883 Method 2027 Tensile Strength of Die Attachment Custom per Device RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. Pass / Fail Criteria Within Electrical & Hermetic Spec. (Note 1) E-mail: [email protected] http://www.rfm.com SF1091A-100605 Page 9 of 9