SH3004-DC70A Printhead Near edge thermal printhead (with thermal historical control) SH3004-DC70A SH-DC70 series was developed with two key structures step-free and near edge for the packaging printer market which requires high speed continuous printing. It is suitable for printers in factory line where high speed 24 hours continuous printing is required. zApplications Barcode printer Label printer Packaging printer Ticket printer Scale printer ATM zFeatures 1) ROHM new technology “STEP FREE” structure will provide, high corrosion resistance, better resistance against scratching damage, high efficiency. 2) Head inclination by near-edge structure, applicable to the large-size platen. Resin type thermal-transfer ink-ribbon can be used. 3) High-hardness protect cote type “W-coat” is employed with 150km abrasion life-time. 4) A built in history-control functionality, high-speed printing up to 300mm / s can be achieved at 300dpi with clear print image. zExternal dimensions (Unit : mm) DOT No.1 124±0.5 6±0.5 108.416 MAX.51 BU9630 Print Direc tion (7.792) Max.4.5 Max.11 #20 #2 #6 #1 Type of PRINTHEAD #1 CONNECTOR:A #19 100±0.2 CONNECTOR:B 3-M3 Effective Depth 3 φ3 H10 Effective Depth 3 (21.2) 20.45±0.2 2.8±0.2 7.3±0.3 31.0±0.5 (43) 10±0.2 φ3 H10 Length 4 Effective Depth 3 14.208±0.3 40±0.3 80±0.3 DOT No.1 1/3 SH3004-DC70A Printhead zEquivalent circuit DOT #1280 VH (COM) DOT #1 220µF 35V GND 0.1µF 50V VDD (+5) / STB2 / STB1 BEO / RESET LATCH REGISTER SHIFT REGISTER SHIFT REGISTER CLK (CP) DI2 DI1 / LOAD START TO EACH IC INC SEL2 SEL1 TM TM THERMISTOR 30kΩ B: 3950K DI No. DOT No. / STB No. DI2 1280 to 641 / STB2 DI1 640 to / STB1 1 DOT No. 1280 to 641 640 to 1 zPin assignments CONNECTOR : A CONNECTOR : B No. Circuit No. Circuit No. Circuit No. Circuit 1 VDD 2 BEO 1 VH (COM) 2 VH (COM) 3 GND 4 DI2 3 VH (COM) 4 GND 5 5 GND 6 GND GND 6 CLK (CP) 7 /LOAD 8 START 9 INC 10 DI1 11 SEL2 12 SEL1 13 /RESET 14 /STB2 15 /STB1 16 TM 17 TM 18 SENS1 19 SENS2 20 SENS3 2/3 SH3004-DC70A Printhead zCharacteristics Parameter Symbol Typical Unit Effective printing width − 108.416 mm Dot pitch − 0.0847 mm Total dot number − 1280 dots Rave 850 Ω Average resistance value Applied voltage VH 24 V Applied power PO 0.57 W/dot SLT 0.28 ms Maximum number of dots energized simultaneously − 1280 dots Maximum clock frequency − 8 MHz Maximum roller diameter − φ50 mm Running life / pulse life − 150/(1×108) km/pulses Operating temperature − 5 to 45 °C Print cycle 3/3 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1