SILABS SIM3C154-B-GM

SiM3C1xx
High-Performance, Low-Power, 32-Bit Precision32™
MCU Family with up to 256 kB of Flash
32-bit ARM® Cortex™-M3 CPU
- 80 MHz maximum frequency
- Single-cycle multiplication, hardware division support
- Nested vectored interrupt control (NVIC) with 16 levels of
interrupt priority
Memory
- 32–256 kB Flash, in-system programmable
- 8–32 kB SRAM (including 4 kB retention SRAM)
- External bus interface supports up to 16 MB of external memory and a parallel LCD interface with QVGA resolution
Power Management
- Low drop-out (LDO) regulator
- Power-on reset circuit and brownout detectors
- 5-to-3.3 V voltage regulator supports up to 150 mA to drive the
-
device directly from up to 5 V supply
Programmable external regulator supports up to 3.6 V,
1000 mA
Multiple power modes supported for low power optimization
Clock Sources
- Internal oscillator with PLL: Fine frequency resolution up to
-
80 MHz; spread-spectrum mode for reduced EMI
Low power internal oscillator: 20 MHz and 2.5 MHz modes
Low frequency internal oscillator: 16.4 kHz
External oscillators: Crystal, RC, C, CMOS and RTC Crystal
Flexible clock divider: Reduce frequency by up to 128x from
any clock source
128/192/256-bit Hardware AES Encryption
- Hardware-supported Electronic Codebook (ECB), Cipher-Block
-
Chaining (CBC) and Counter (CTR) algorithms
All cipher operations can be performed without any firmware
intervention for a set of 4-word blocks (up to 32 kB)
16/32-bit CRC
- Hardware support for common 32-bit and 16-bit polynomials
Timers/Counters
- 2 x 32-bit or 4 x 16-bit timers with capture/compare
- 2 x 16-bit, 2-channel counters with capture/compare/PWM
- 16-bit, 6-channel counter with capture/compare/PWM and
dead-time controller with differential outputs
- 16-bit low power timer/pulse counter operational in the lowest
power mode
- 32-bit real time clock (RTC) with multiple alarms
- Watchdog timer
Current-to-Voltage Converter
- Supports up to 6 mA input range
Supply Voltage
- 2.7 to 5.5 V (regulator enabled)
- 1.8 to 3.6 V (regulator disabled)
Preliminary Rev. 0.8 2/12
Low Power Features
- 85 nA current mode with voltage supply monitor enabled
- 350 nA current mode with RTC (internal oscillator)
- 620 nA current mode with RTC (external oscillator)
- 10 µs wakeup (lowest power mode); 1.5 µs analog setting time
- 275 µA/MHz active current
- Clocks can be gated off from unused peripherals to save power
2 x 12-Bit Analog-to-Digital Converters
- Up to 28 input channels
- Up to 250 ksps 12-bit mode or 1 Msps 10-bit mode
- Single, simultaneous, and interleaving modes supported
- Channel sequencer enables automatic multiplexing of multiple
channels without firmware intervention
- Internal VREF or external VREF supported
2 x 10-Bit Digital-to-Analog Converters
- DMA support for waveform generation
- Four-word circular buffer to enable 12-bit mode
16-Channel Capacitance-to-Digital Converter
- Supports buttons, sliders, wheels, and capacitive proximity
- Fast conversion time; <1 µA wake-on-touch average current
Two Low-Current Comparators
- Integrated 6-bit programmable reference voltage
- 400 nA current consumption in low power mode
16-Channel DMA Controller
- Supports ADC, DAC, I2C, I2S, SPI, USART, AES, EPCA,
capacitive sensing, external triggers, and timers
Up to 65 Flexible I/O
- Up to 59 contiguous GPIO with two priority crossbars providing
flexibility in pin assignments; 12 x 5 V tolerant GPIO
- Up to 6 programmable high drive capable (5–300 mA, 1.8–6 V)
I/O can drive LEDs, power MOSFETs, buzzers, etc.
Communication Interfaces
- 2 x USARTs and 2 x UARTs with IrDA and ISO7816 SmartCard
- 3 x SPIs, 2 x I2C, I2S (receive and transmit)
On-Chip Debugging
- Serial wire debug (SWD) and JTAG allow for full-speed, nonintrusive debug
- Serial wire viewer (SWV) available in 64 / 80 / 92-pin packages
- Cortex-M3 embedded trace macrocell (ETM) in 80 / 92-pin
packages
Temperature Range: –40 to +85 °C
Package Options
- QFN options: 40-pin (6 x 6 mm), 64-pin (9 x 9 mm)
- TQFP options: 64-pin (10 x 10 mm), 80-pin (12 x 12 mm)
- LGA option: 92-pin (7 x 7 mm)
Copyright © 2012 by Silicon Laboratories
SiM3C1xx
This information applies to a product under development. Its characteristics and specifications are subject to change without notice.
SiM3C1xx
Ta ble of Contents
1. Related Documents and Conventions ...............................................................................4
1.1. Related Documents........................................................................................................4
1.1.1. SiM3U1xx/SiM3C1xx Reference Manual...............................................................4
1.1.2. Hardware Access Layer (HAL) API Description ....................................................4
1.1.3. ARM Cortex-M3 Reference Manual.......................................................................4
1.2. Conventions ...................................................................................................................4
2. Typical Connection Diagrams ............................................................................................5
2.1. Power .............................................................................................................................5
3. Electrical Specifications......................................................................................................6
3.1. Electrical Characteristics ................................................................................................6
3.2. Thermal Conditions ...................................................................................................... 28
3.3. Absolute Maximum Ratings..........................................................................................28
4. Precision32™ SiM3C1xx System Overview .................................................................... 31
4.1. Power ........................................................................................................................... 33
4.1.1. LDO and Voltage Regulator (VREG0) ................................................................. 33
4.1.2. Voltage Supply Monitor (VMON0) ....................................................................... 33
4.1.3. External Regulator (EXTVREG0) ........................................................................ 33
4.1.4. Power Management Unit (PMU).......................................................................... 33
4.1.5. Device Power Modes........................................................................................... 34
4.2. I/O................................................................................................................................. 36
4.2.1. General Features.................................................................................................36
4.2.2. High Drive Pins (PB4)..........................................................................................36
4.2.3. 5 V Tolerant Pins (PB3) ....................................................................................... 36
4.2.4. Crossbars ............................................................................................................ 36
4.3. Clocking........................................................................................................................ 37
4.3.1. PLL (PLL0)........................................................................................................... 38
4.3.2. Low Power Oscillator (LPOSC0) ......................................................................... 38
4.3.3. Low Frequency Oscillator (LFOSC0)................................................................... 38
4.3.4. External Oscillators (EXTOSC0).......................................................................... 38
4.4. Data Peripherals...........................................................................................................39
4.4.1. 16-Channel DMA Controller................................................................................. 39
4.4.2. 128/192/256-bit Hardware AES Encryption (AES0) ............................................ 39
4.4.3. 16/32-bit CRC (CRC0)......................................................................................... 39
4.5. Counters/Timers and PWM ..........................................................................................40
4.5.1. Programmable Counter Array (EPCA0, PCA0, PCA1)........................................ 40
4.5.2. 32-bit Timer (TIMER0, TIMER1).......................................................................... 40
4.5.3. Real-Time Clock (RTC0) ..................................................................................... 41
4.5.4. Low Power Timer (LPTIMER0)............................................................................41
4.5.5. Watchdog Timer (WDTIMER0)............................................................................41
4.6. Communications Peripherals ....................................................................................... 42
4.6.1. External Memory Interface (EMIF0).....................................................................42
4.6.2. USART (USART0, USART1)............................................................................... 42
4.6.3. UART (UART0, UART1) ...................................................................................... 42
4.6.4. SPI (SPI0, SPI1) .................................................................................................. 43
2
Preliminary Rev. 0.8
SiM3C1xx
4.6.5. I2C (I2C0, I2C1)................................................................................................... 43
4.6.6. I2S (I2S0)............................................................................................................. 44
4.7. Analog .......................................................................................................................... 45
4.7.1. 12-Bit Analog-to-Digital Converters (SARADC0, SARADC1).............................. 45
4.7.2. Sample Sync Generator (SSG0) ......................................................................... 45
4.7.3. 10-Bit Digital-to-Analog Converter (IDAC0, IDAC1) ............................................ 45
4.7.4. 16-Channel Capacitance-to-Digital Converter (CAPSENSE0) ............................ 46
4.7.5. Low Current Comparators (CMP0, CMP1) .......................................................... 46
4.7.6. Current-to-Voltage Converter (IVC0) ................................................................... 46
4.8. Reset Sources..............................................................................................................47
4.9. Security ........................................................................................................................ 48
4.10.On-Chip Debugging ..................................................................................................... 48
5. Pin Definitions and Packaging Information.....................................................................49
5.1. SiM3C1x7 Pin Definitions............................................................................................. 49
5.2. SiM3C1x6 Pin Definitions............................................................................................. 57
5.3. SiM3C1x4 Pin Definitions............................................................................................. 64
6. Ordering Information .........................................................................................................68
6.1. LGA-92 Package Specifications...................................................................................70
6.1.1. LGA-92 Solder Mask Design ............................................................................... 72
6.1.2. LGA-92 Stencil Design ........................................................................................ 72
6.1.3. LGA-92 Card Assembly ....................................................................................... 72
6.2. TQFP-80 Package Specifications ................................................................................ 73
6.2.1. TQFP-80 Solder Mask Design............................................................................. 76
6.2.2. TQFP-80 Stencil Design ...................................................................................... 76
6.2.3. TQFP-80 Card Assembly..................................................................................... 76
6.3. QFN-64 Package Specifications .................................................................................. 77
6.3.1. QFN-64 Solder Mask Design............................................................................... 79
6.3.2. QFN-64 Stencil Design ........................................................................................ 79
6.3.3. QFN-64 Card Assembly....................................................................................... 79
6.4. TQFP-64 Package Specifications ................................................................................ 80
6.4.1. TQFP-64 Solder Mask Design............................................................................. 83
6.4.2. TQFP-64 Stencil Design ...................................................................................... 83
6.4.3. TQFP-64 Card Assembly..................................................................................... 83
6.5. QFN-40 Package Specifications .................................................................................. 84
6.5.1. QFN-40 Solder Mask Design............................................................................... 86
6.5.2. QFN-40 Stencil Design ........................................................................................ 86
6.5.3. QFN-40 Card Assembly....................................................................................... 86
7. Revision Specific Behavior............................................................................................... 87
7.1. Revision Identification .................................................................................................. 87
7.2. Comparator Rising/Falling Edge Flags in Debug Mode (CMP0, CMP1)...................... 88
7.2.1. Problem ...............................................................................................................88
7.2.2. Impacts ................................................................................................................ 88
7.2.3. Workaround ......................................................................................................... 88
7.2.4. Resolution............................................................................................................ 88
Contact Information ................................................................................................................ 90
Preliminary Rev. 0.8
3
SiM3C1xx
1. Related Documents and Conventions
1.1. Related Documents
This data sheet accompanies several documents to provide the complete description of the SiM3C1xx device
family.
1.1.1. SiM3U1xx/SiM3C1xx Reference Manual
The Silicon Laboratories SiM3U1xx/SiM3C1xx Reference Manual provides detailed functional descriptions for the
SiM3C1xx devices.
1.1.2. Hardware Access Layer (HAL) API Description
The Silicon Laboratories Hardware Access Layer (HAL) API provides C-language functions to modify and read
each bit in the SiM3C1xx devices. This description can be found in the SiM3xxxx HAL API Reference Manual.
1.1.3. ARM Cortex-M3 Reference Manual
The ARM-specific features like the Nested Vector Interrupt Controller are described in the ARM Cortex-M3
reference documentation. The online reference manual can be found here:
http://infocenter.arm.com/help/topic/com.arm.doc.subset.cortexm.m3/index.html#cortexm3.
1.2. Conventions
The block diagrams in this document use the following formatting conventions:
Internal Module
Other Internal
Peripheral Block
External Memory
Block
DMA Block
Memory Block
Input_Pin
External to MCU
Block
Output_Pin
Functional Block
Internal_Input_Signal
Internal_Output_Signal
REGn_NAME / BIT_NAME
Figure 1.1. Block Diagram Conventions
4
Preliminary Rev. 0.8
SiM3C1xx
2. Typical Connection Diagrams
This section provides typical connection diagrams for SiM3C1xx devices.
2.1. Power
Figure 2.1 shows a typical connection diagram for the power pins of the SiM3C1xx devices when the internal
regulator is in use.
SiM3C1xx Device
5 V (in)
VREGn
3.3 V (out)
1 uF and 0.1 uF bypass
capacitors required for
each power pin placed
as close to the pins as
possible.
VREGIN
VIOHD
VDD
VIO
VSS
VSSHD
Figure 2.1. Connection Diagram with Voltage Regulator Used
Figure 2.2 shows a typical connection diagram for the power pins of the SiM3C1xx devices when the internal
regulator is not used.
SiM3C1xx Device
1.8-3.6 V (in)
VREGn
VREGIN
VIOHD
1 uF and 0.1 uF bypass
capacitors required for
each power pin placed
as close to the pins as
possible.
VDD
VIO
VSS
VSSHD
Figure 2.2. Connection Diagram with Voltage Regulator Not Used
Preliminary Rev. 0.8
5
SiM3C1xx
3. Electrical Specifications
3.1. Electrical Characteristics
All electrical parameters in all tables are specified under the conditions listed in Table 3.1, unless stated otherwise.
Table 3.1. Recommended Operating Conditions
Parameter
Operating Supply Voltage on VDD
Operating Supply Voltage on VREGIN
Operating Supply Voltage on VIO
Operating Supply Voltage on VIOHD
Symbol
Conditions
Min
Typ
Max
Units
1.8
—
3.6
V
EXTVREG0 Not Used
4
—
5.5
V
EXTVREG0 Used
3.0
—
3.6
V
1.8
—
VDD
V
HV Mode (default)
2.7
—
6.0
V
LV Mode
1.8
—
3.6
V
VSS
—
VIO
V
SiM3C1x7
PB3.0–PB3.7 and
RESET
VSS
—
VIO+2.0
V
SiM3C1x7
PB3.8 - PB3.11
VSS
—
Lowest
of
VIO+2.0
or
VREGIN
V
SiM3C1x6
PB3.0–PB3.5 and
RESET
VSS
—
VIO+2.0
V
SiM3C1x6
PB3.6–PB3.9
VSS
—
Lowest
of
VIO+2.0
or
VREGIN
V
SiM3C1x4
RESET
VSS
—
VIO+2.0
V
SiM3C1x4
PB3.0–PB3.3
VSS
—
Lowest
of
VIO+2.0
or
VREGIN
V
VDD
VREGIN
VIO
VIOHD
Voltage on I/O pins, Port Bank 0, 1
and 2 I/O
VIN
Voltage on I/O pins, Port Bank 3 I/O
and RESET
VIN
Voltage on I/O pins, Port Bank 4 I/O
VIN
VSSHD
—
VIOHD
V
System Clock Frequency (AHB)
fAHB
0
—
80
MHz
Peripheral Clock Frequency (APB)
fAPB
0
—
50
MHz
Operating Ambient Temperature
TA
–40
—
85
°C
Operating Junction Temperature
TJ
–40
—
105
°C
Note: All voltages with respect to VSS.
6
Preliminary Rev. 0.8
SiM3C1xx
Table 3.2. Power Consumption
Parameter
Symbol
Conditions
Min
Typ
Max
Units
IDD
FAHB = 80 MHz,
FAPB = 40 MHz
—
33
36.5
mA
FAHB = FAPB = 20 MHz
—
10.5
13.3
mA
FAHB = FAPB = 2.5 MHz
—
2.0
3.8
mA
FAHB = 80 MHz,
FAPB = 40 MHz
—
22
24.9
mA
FAHB = FAPB = 20 MHz
—
7.8
10
mA
FAHB = FAPB = 2.5 MHz
—
1.2
3
mA
FAHB = 80 MHz,
FAPB = 40 MHz
—
30.5
35.5
mA
FAHB = FAPB = 20 MHz
—
8.5
10
mA
FAHB = FAPB = 2.5 MHz
—
1.7
3.5
mA
FAHB = 80 MHz,
FAPB = 40 MHz
—
20
23
mA
FAHB = FAPB = 20 MHz
—
5.3
7.3
mA
FAHB = FAPB = 2.5 MHz
—
1.0
2.8
mA
FAHB = 80 MHz,
FAPB = 40 MHz
—
19
22
mA
FAHB = FAPB = 20 MHz
—
7.8
9.7
mA
FAHB = FAPB = 2.5 MHz
—
1.3
3
mA
VDD = 1.8 V, TA = 25 °C
—
175
—
µA
VDD = 3.0 V, TA = 25 °C
—
250
—
µA
Digital Core Supply Current
Normal Mode2,3,4,5—Full speed
with code executing from Flash,
peripheral clocks ON
Normal Mode2,3,4,5—Full speed
with code executing from Flash,
peripheral clocks OFF
Power Mode 12,3,4,6—Full speed
with code executing from RAM,
peripheral clocks ON
Power Mode 12,3,4,6—Full speed
with code executing from RAM,
peripheral clocks OFF
Power Mode 22,3,4—Core halted
with peripheral clocks ON
Power Mode 32,3
IDD
IDD
IDD
IDD
IDD
Notes:
1. Perhipheral currents drop to zero when peripheral clock and peripheral are disabled, unless otherwise noted.
2. Currents are additive. For example, where IDD is specified and the mode is not mutually exclusive, enabling the
functions increases supply current by the specified amount.
3. Includes all peripherals that cannot have clocks gated in the Clock Control module.
4. Includes supply current from internal regulator and PLL0OSC (>20 MHz) or LPOSC0 (<=20 MHz).
5. Flash execution numbers use 2 wait states for 80 MHz and 0 wait states at 20 MHz or less.
6. RAM execution numbers use 0 wait states for all frequencies.
7. IDAC output current and IVC input current not included.
8. Bias current only. Does not include dynamic current from oscillator running at speed.
Preliminary Rev. 0.8
7
SiM3C1xx
Table 3.2. Power Consumption (Continued)
Parameter
Power Mode 92,3—Low Power
Shutdown with VREG0 disabled,
powered through VDD and VIO
Power Mode 92,3—Low Power
Shutdown with VREG0 in lowpower mode, VDD and VIO powered through VREG0 (Includes
VREG0 current)
VIOHD Current (High-drive I/O disabled)
Symbol
Conditions
Min
Typ
Max
Units
IDD
RTC Disabled,
VDD = 1.8 V, TA = 25 °C
—
85
—
nA
RTC w/ 16.4 kHz LFO,
VDD = 1.8 V, TA = 25 °C
—
350
—
nA
RTC w/ 32.768 kHz Crystal,
VDD = 1.8 V, TA = 25 °C
—
620
—
nA
RTC Disabled,
VDD = 3.0 V, TA = 25 °C
—
145
—
nA
RTC w/ 16.4 kHz LFO,
VDD = 3.0 V, TA = 25 °C
—
500
—
nA
RTC w/ 32.768 kHz Crystal,
VDD = 3.0 V, TA = 25 °C
—
800
—
nA
RTC Disabled,
VREGIN = 5 V, TA = 25 °C
—
300
—
nA
RTC w/ 16.4 kHz LFO,
VREGIN = 5 V, TA = 25 °C
—
650
—
nA
RTC w/ 32.768 kHz Crystal,
VREGIN = 5 V, TA = 25 °C
—
950
—
nA
HV Mode (default)
—
2.5
5
µA
LV Mode
—
2
—
nA
IVREGIN
IVIOHD
Notes:
1. Perhipheral currents drop to zero when peripheral clock and peripheral are disabled, unless otherwise noted.
2. Currents are additive. For example, where IDD is specified and the mode is not mutually exclusive, enabling the
functions increases supply current by the specified amount.
3. Includes all peripherals that cannot have clocks gated in the Clock Control module.
4. Includes supply current from internal regulator and PLL0OSC (>20 MHz) or LPOSC0 (<=20 MHz).
5. Flash execution numbers use 2 wait states for 80 MHz and 0 wait states at 20 MHz or less.
6. RAM execution numbers use 0 wait states for all frequencies.
7. IDAC output current and IVC input current not included.
8. Bias current only. Does not include dynamic current from oscillator running at speed.
8
Preliminary Rev. 0.8
SiM3C1xx
Table 3.2. Power Consumption (Continued)
Parameter
Symbol
Conditions
Min
Typ
Max
Units
IVREGIN
Normal Mode, TA = 25 °C
BGDIS = 0, SUSEN = 0
—
300
—
µA
Normal Mode, TA = 85 °C
BGDIS = 0, SUSEN = 0
—
—
650
µA
Suspend Mode, TA = 25 °C
BGDIS = 0, SUSEN = 1
—
75
—
µA
Suspend Mode, TA = 85 °C
BGDIS = 0, SUSEN = 1
—
—
115
µA
Sleep Mode, TA = 25 °C
BGDIS = 1, SUSEN = X
—
90
—
nA
Sleep Mode, TA = 85 °C
BGDIS = 1, SUSEN = X
—
—
500
nA
Regulator
—
215
250
µA
Current Sensor
—
7
—
µA
Analog Peripheral Supply Currents
Voltage Regulator (VREG0)
External Regulator (EXTVREG0)
IEXTVREG
PLL0 Oscillator (PLL0OSC)
IPLLOSC
Operating at 80 MHz
—
1.75
1.86
mA
Low-Power Oscillator (LPOSC0)
ILPOSC
Operating at 20 MHz
—
190
—
µA
Operating at 2.5 MHz
—
40
—
µA
Operating at 16.4 kHz,
TA = 25 °C
—
215
—
nA
Operating at 16.4 kHz,
TA = 85 °C
—
—
500
nA
Low-Frequency Oscillator
(LFOSC0)
ILFOSC
Notes:
1. Perhipheral currents drop to zero when peripheral clock and peripheral are disabled, unless otherwise noted.
2. Currents are additive. For example, where IDD is specified and the mode is not mutually exclusive, enabling the
functions increases supply current by the specified amount.
3. Includes all peripherals that cannot have clocks gated in the Clock Control module.
4. Includes supply current from internal regulator and PLL0OSC (>20 MHz) or LPOSC0 (<=20 MHz).
5. Flash execution numbers use 2 wait states for 80 MHz and 0 wait states at 20 MHz or less.
6. RAM execution numbers use 0 wait states for all frequencies.
7. IDAC output current and IVC input current not included.
8. Bias current only. Does not include dynamic current from oscillator running at speed.
Preliminary Rev. 0.8
9
SiM3C1xx
Table 3.2. Power Consumption (Continued)
Parameter
External Oscillator (EXTOSC0)8
SARADC0,
SARADC1
Temperature Sensor
Internal SAR Reference
Symbol
Conditions
Min
Typ
Max
Units
IEXTOSC
FREQCN = 111
—
3.8
4.7
mA
FREQCN = 110
—
840
950
µA
FREQCN = 101
—
185
220
µA
FREQCN = 100
—
65
80
µA
FREQCN = 011
—
25
30
µA
FREQCN = 010
—
10
15
µA
FREQCN = 001
—
5
10
µA
FREQCN = 000
—
3
8
µA
Sampling at 1 Msps, highest
power mode settings.
—
1.2
1.5
mA
Sampling at 250 ksps, lowest
power mode settings.
—
390
510
µA
—
75
105
µA
Normal Power Mode
—
680
750
µA
Low Power Mode
—
160
190
µA
—
75
100
µA
CMPMD = 11
—
0.5
—
µA
CMPMD = 10
—
3
—
µA
CMPMD = 01
—
10
—
µA
CMPMD = 00
—
25
—
µA
Continuous Conversions
—
55
80
µA
—
75
90
µA
—
1.5
1.9
µA
—
15
25
µA
ISARADC
ITSENSE
IREFFS
VREF0
IREFP
Comparator 0 (CMP0),
Comparator 1 (CMP1)
ICMP
Capacitive Sensing (CAPSENSE0)
ICS
IDAC07,
IDAC17
IIDAC
IVC07
IIVC
Voltage Supply Monitor (VMON0)
IIN = 0
IVMON
Notes:
1. Perhipheral currents drop to zero when peripheral clock and peripheral are disabled, unless otherwise noted.
2. Currents are additive. For example, where IDD is specified and the mode is not mutually exclusive, enabling the
functions increases supply current by the specified amount.
3. Includes all peripherals that cannot have clocks gated in the Clock Control module.
4. Includes supply current from internal regulator and PLL0OSC (>20 MHz) or LPOSC0 (<=20 MHz).
5. Flash execution numbers use 2 wait states for 80 MHz and 0 wait states at 20 MHz or less.
6. RAM execution numbers use 0 wait states for all frequencies.
7. IDAC output current and IVC input current not included.
8. Bias current only. Does not include dynamic current from oscillator running at speed.
10
Preliminary Rev. 0.8
SiM3C1xx
Table 3.2. Power Consumption (Continued)
Parameter
Symbol
Conditions
Min
Typ
Max
Units
Flash Current on VDD
Write Operation
IFLASH-W
—
—
8
mA
Erase Operation
IFLASH-E
—
—
15
mA
Notes:
1. Perhipheral currents drop to zero when peripheral clock and peripheral are disabled, unless otherwise noted.
2. Currents are additive. For example, where IDD is specified and the mode is not mutually exclusive, enabling the
functions increases supply current by the specified amount.
3. Includes all peripherals that cannot have clocks gated in the Clock Control module.
4. Includes supply current from internal regulator and PLL0OSC (>20 MHz) or LPOSC0 (<=20 MHz).
5. Flash execution numbers use 2 wait states for 80 MHz and 0 wait states at 20 MHz or less.
6. RAM execution numbers use 0 wait states for all frequencies.
7. IDAC output current and IVC input current not included.
8. Bias current only. Does not include dynamic current from oscillator running at speed.
Table 3.3. Power Mode Wake Up Times
Parameter
Min
Typ
Max
Units
tPM3FW
—
425
—
µs
Power Mode 3 Wake Time
tPM3
—
1.35
—
ms
Power Mode 9 Wake Time
tPM9
—
12
—
µs
Power Mode 3 Fast Wake Time
Symbol
Conditions
Preliminary Rev. 0.8
11
SiM3C1xx
Table 3.4. Reset and Supply Monitor
Parameter
Symbol
Conditions
Min
Typ
Max
Units
VDD High Supply Monitor Threshold
(VDDHITHEN = 1)
VVDDMH
Early Warning
2.10
2.20
2.30
V
Reset
1.95
2.05
2.1
V
VDD Low Supply Monitor Threshold
(VDDHITHEN = 0)
VVDDML
Early Warning
1.81
1.85
1.88
V
Reset
1.70
1.74
1.77
V
VREGIN Supply Monitor Threshold
VVREGM
Early Warning
4.2
4.4
4.6
V
Power-On Reset (POR) Threshold
VPOR
Rising Voltage on VDD
—
1.4
—
V
Falling Voltage on VDD
0.8
1
1.3
V
VDD Ramp Time
tRMP
Time to VDD > 1.8 V
10
—
3000
µs
Reset Delay from POR
tPOR
Relative to VDD >
VPOR
3
—
100
ms
Reset Delay from non-POR source
tRST
Time between release
of reset source and
code execution
—
10
—
µs
RESET Low Time to Generate Reset
tRSTL
50
—
—
ns
Missing Clock Detector Response
Time (final rising edge to reset)
tMCD
—
0.4
1
ms
Missing Clock Detector Trigger 
Frequency
FMCD
—
7.5
13
kHz
VDD Supply Monitor Turn-On Time
tMON
—
2
—
µs
12
FAHB > 1 MHz
Preliminary Rev. 0.8
SiM3C1xx
Table 3.5. On-Chip Regulators
Parameter
Symbol
Conditions
Min
Typ
Max
Units
4 < VREGIN < 5.5
BGDIS = 0, SUSEN = 0
3.2
3.3
3.4
V
4 < VREGIN < 5.5
BGDIS = 0, SUSEN = 1
3.2
3.3
3.4
V
4 < VREGIN < 5.5
BGDIS = 1, SUSEN = X
IDDOUT = 500 µA
2.3
2.8
3.6
V
4 < VREGIN < 5.5
BGDIS = 1, SUSEN = X
IDDOUT = 5 mA
2.1
2.65
3.3
V
4 < VREGIN < 5.5
BGDIS = 0, SUSEN = X
—
—
150
mA
4 < VREGIN < 5.5
BGDIS = 1, SUSEN = X
—
—
5
mA
BGDIS = 0
—
0.1
1
mV/mA
1
—
10
µF
3.3 V Regulator Characteristics (VREG0, Supplied from VREGIN Pin)
Output Voltage (at VDD pin)
Output Current (at VDD pin)*
VDDOUT
IDDOUT
Output Load Regulation
VDDLR
Output Capacitance
CVDD
*Note: Total current VREG0 is capable of providing. Any current consumed by the SiM3C1xx reduces the current available to
external devices powered from VDD.
Preliminary Rev. 0.8
13
SiM3C1xx
Table 3.6. External Regulator
Parameter
Symbol
Input Voltage Range (at VREGIN)
VREGIN
Conditions
Min
Typ
Max
Units
3.0
—
3.6
V
Output Voltage (at
EXREGOUT)
VEXREGOUT
Programmable in
100 mV steps
1.8
—
3.6
V
NPN Current Drive
INPN
400 mV Dropout
12
—
—
mA
PNP Current Drive
IPNP
VEXREGBD > VREGIN1.5 V
–6
—
—
mA
VEXREGBD
VREGIN >= 3.5 V
VREGIN –
2.0
—
—
V
VREGIN < 3.5 V
1.5
—
—
V
400mV Dropout
—
—
11.5
mA
EXREGBD Voltage (PNP
Mode)
Standalone Mode Output
Current
IEXTREGBD
External Capacitance with
External BJT
CBJT
4.7
—
—
µF
Standalone Mode Load Regulation
LRSTAND-
—
1
—
mV/mA
Standalone Mode External
Capacitance
CSTAND-
47
—
—
nF
10
—
720
mA
Current Limit Accuracy
—
—
10
%
Foldback Limit Accuracy
—
—
20
%
RSENSE
—
—
1

Internal Pull-Down
RPD
—
10
—
k
Internal Pull-Up
RPU
—
5
—
k
Current Limit Range
Current Sense Resistor
ALONE
ALONE
ILIMIT
1  Sense Resistor
Current Sensor
Sensing Pin Voltage
VEXTREGSP
VEXTREGSN
Measured at
EXTREGSP or
EXTREGSN pin
2.2
—
VREGIN
V
Differential Sensing Voltage
VDIFF
(VEXTREGSP VEXTREGSN)
10
—
1600
mV
Current at EXTREGSN Pin
IEXTREGSN
—
8
—
A
Current at EXTREGSP Pin
IEXTREGSP
—
VDIFF x 2
00 + 12
—
A
14
Preliminary Rev. 0.8
SiM3C1xx
Table 3.7. Flash Memory
Parameter
Write Time
1
Erase Time1
Symbol
Conditions
Min
Typ
Max
Units
tWRITE
One 16-bit Half Word
20
21
22
µs
tERASE
One Page
20
21
22
ms
tERALL
Full Device
20
21
22
ms
VDD Voltage During Programming
VPROG
1.8
—
3.6
V
Endurance (Write/Erase Cycles)
NWE
20k
TBD
—
Cycles
Retention2
tRET
TBD
TBD
—
Years
TA = 85 °C, 1k Cycles
Notes:
1. Does not include sequencing time before and after the write/erase operation, which may be multiple AHB clock cycles.
2. Additional Data Retention Information is published in the Quarterly Quality and Reliability Report.
Table 3.8. Internal Oscillators
Parameter
Symbol
Conditions
Min
Typ
Max
Units
fPLL0OSC
Full Temperature and
Supply Range
77
79
80
MHz
Power Supply Sensitivity*
PSSPLL0OSC
TA = 25 °C,
Fout = 79 MHz
—
430
—
ppm/V
Temperature Sensitivity*
TSPLL0OSC
VDD = 3.3 V,
Fout = 79 MHz
—
95
—
ppm/°C
23
—
80
MHz
fREF = 20 MHz,
fPLL0OSC = 80 MHz,
M=24, N=99,
LOCKTH = 0
—
1.7
—
µs
fREF = 32 kHz,
fPLL0OSC = 80 MHz,
M=0, N=2440,
LOCKTH = 0
—
91
—
µs
Phase-Locked Loop (PLL0OSC)
Calibrated Output Frequency*
Adjustable Output Frequency
Range
fPLL0OSC
Lock Time
tPLL0LOCK
Preliminary Rev. 0.8
15
SiM3C1xx
Table 3.8. Internal Oscillators
Parameter
Symbol
Conditions
Min
Typ
Max
Units
fLPOSC
Full Temperature and
Supply Range
19
20
21
MHz
TA = 25 °C,
VDD = 3.3 V
19.6
20
20.4
MHz
fLPOSCD
Full Temperature and
Supply Range
2.375
2.5
2.625
MHz
Power Supply Sensitivity
PSSLPOSC
TA = 25 °C
—
0.5
—
%/V
Temperature Sensitivity
TSLPOSC
VDD = 3.3 V
—
55
—
ppm/°C
Full Temperature and
Supply Range
13.4
16.4
19.7
kHz
TA = 25 °C,
VDD = 3.3 V
15.8
16.4
17.3
kHz
Low Power Oscillator (LPOSC0)
Oscillator Frequency
Divided Oscillator Frequency
Low Frequency Oscillator (LFOSC0)
Oscillator Frequency
fLFOSC
Power Supply Sensitivity
PSSLFOSC
TA = 25 °C
—
2.4
—
%/V
Temperature Sensitivity
TSLFOSC
VDD = 3.3 V
—
0.2
—
%/°C
RTC0 Oscillator (RTC0OSC)
Missing Clock Detector Trigger
Frequency
fRTCMCD
—
8
15
kHz
RTC Robust Duty Cycle Range
DCRTC
25
—
55
%
Min
Typ
Max
Units
*Note: PLL0OSC in free-running oscillator mode
Table 3.9. External Oscillator
Parameter
Symbol
Conditions
External Input CMOS Clock
Frequency
fCMOS
0
—
50
MHz
External Input CMOS Clock High Time
tCMOSH
9
—
—
ns
External Input CMOS Clock Low Time
tCMOSL
9
—
—
ns
16
Preliminary Rev. 0.8
SiM3C1xx
Table 3.10. SAR ADC
Parameter
Resolution
Supply Voltage Requirements
(VDD)
Symbol
Conditions
Nbits
12 Bit Mode
12
Bits
10 Bit Mode
10
Bits
VADC
Throughput Rate
(High Speed Mode)
fS
Throughput Rate
(Low Power Mode)
fS
Tracking Time
SAR Clock Frequency
tTRK
fSAR
Min
Typ
Max
Units
High Speed Mode
2.2
—
3.6
V
Low Power Mode
1.8
—
3.6
V
12 Bit Mode
—
—
250
ksps
10 Bit Mode
—
—
1
Msps
12 Bit Mode
—
—
62.5
ksps
10 Bit Mode
—
—
250
ksps
High Speed Mode
230
—
—
ns
Low Power Mode
450
—
—
ns
High Speed Mode
—
—
16.24
MHz
Low Power Mode
—
—
4
MHz
Conversion Time
tCNV
10-Bit Conversion,
SAR Clock = 16 MHz,
APB Clock = 40 MHz.
Sample/Hold Capacitor
CSAR
Gain = 1
—
5
—
pF
Gain = 0.5
—
2.5
—
pF
High Quality Inputs
—
18
—
pF
Normal Inputs
—
20
—
pF
High Quality Inputs
—
300
—

Normal Inputs
—
550
—

1
—
VDD
V
Gain = 1
0
—
VREF
V
Gain = 0.5
0
—
2xVREF
V
—
70
—
dB
12 Bit Mode
—
±1
±1.9
LSB
10 Bit Mode
—
±0.2
±0.5
LSB
12 Bit Mode
–1
±0.7
1.8
LSB
10 Bit Mode
—
±0.2
±0.5
LSB
Input Pin Capacitance
Input Mux Impedance
Voltage Reference Range
Input Voltage Range*
Power Supply Rejection Ratio
CIN
RMUX
VREF
VIN
PSRRADC
762.5
ns
DC Performance
Integral Nonlinearity
Differential Nonlinearity 
(Guaranteed Monotonic)
INL
DNL
*Note: Absolute input pin voltage is limited by the lower of the supply at VDD and VIO.
Preliminary Rev. 0.8
17
SiM3C1xx
Table 3.10. SAR ADC (Continued)
Parameter
Offset Error (using AGND)
Offset Temperatue Coefficient
Slope Error
Symbol
Conditions
Min
Typ
Max
Units
EOFF
12 Bit Mode, VREF =2.4 V
–2
0
2
LSB
10 Bit Mode, VREF =2.4 V
–1
0
1
LSB
—
0.004
—
LSB/°C
–0.07
–0.02
0.02
%
TCOFF
EM
12 Bit Mode
Dynamic Performance with External Reference or Internal Reference in High Speed Mode, 10 kHz Sine
Wave Input 1dB below full scale, Max throughput
Signal-to-Noise
Signal-to-Noise Plus Distortion
SNR
SNDR
Total Harmonic Distortion (Up to
5th Harmonic)
THD
Spurious-Free Dynamic Range
SFDR
12 Bit Mode
62
66
—
dB
10 Bit Mode
58
60
—
dB
12 Bit Mode
62
66
—
dB
10 Bit Mode
58
60
—
dB
12 Bit Mode
—
78
—
dB
10 Bit Mode
—
77
—
dB
12 Bit Mode
—
–79
—
dB
10 Bit Mode
—
–74
—
dB
Dynamic Performance with Internal Reference in Low Power Mode, 10 kHz Sine Wave Input 1dB below full
scale, Max throughput
Signal-to-Noise
Signal-to-Noise Plus Distortion
SNR
SNDR
Total Harmonic Distortion (Up to
5th Harmonic)
THD
Spurious-Free Dynamic Range
SFDR
12 Bit Mode
TBD
66
—
dB
10 Bit Mode
TBD
60
—
dB
12 Bit Mode
TBD
66
—
dB
10 Bit Mode
TBD
60
—
dB
12 Bit Mode
—
78
—
dB
10 Bit Mode
—
77
—
dB
12 Bit Mode
—
–72
—
dB
10 Bit Mode
—
–71
—
dB
*Note: Absolute input pin voltage is limited by the lower of the supply at VDD and VIO.
18
Preliminary Rev. 0.8
SiM3C1xx
Table 3.11. IDAC
Parameter
Symbol
Conditions
Min
Typ
Max
Units
Static Performance
Resolution
Nbits
10
Integral Nonlinearity
INL
—
±0.5
±2
LSB
Differential Nonlinearity (Guaranteed
Monotonic)
DNL
—
±0.5
±1
LSB
Output Compliance Range
VOCR
—
—
VDD – 1.0
V
Full Scale Output Current
IOUT
2 mA Range
2.0
2.046
2.10
mA
1 mA Range
1.00
1.023
1.05
mA
0.5 mA Range
495
511.5
525
µA
—
250
—
nA
2 mA Range
—
100
—
ppm/°C
2 mA Range
—
-220
—
ppm/V
—
1
—
k
—
1.2
—
µs
—
3
—
µs
Offset Error
EOFF
Full Scale Error Tempco
TCFS
VDD Power Supply Rejection Ratio
Test Load Impedance (to VSS)
RTEST
Bits
Dynamic Performance
Output Settling Time to 1/2 LSB
min output to max
output
Startup Time
Preliminary Rev. 0.8
19
SiM3C1xx
Table 3.12. Capacitive Sense
Parameter
Symbol
Conditions
Min
Typ
Max
Units
tsingle
12-bit Mode
—
25
—
µs
13-bit Mode
—
27
—
µs
14-bit Mode
—
29
—
µs
16-bit Mode
—
33
—
µs
Highest Gain Setting
(default)
—
45
—
pF
Lowest Gain Setting
—
500
—
pF
Highest Gain Setting
(default)
—
50
—
k
Min
Typ
Max
Units
VDDIVC
2.2
—
3.6
V
Input Pin Voltage
VIN
2.2
—
VDD
V
Minimum Input Current (source)
IIN
100
—
—
µA
INLIVC
–0.6
—
0.6
%
VIVCOUT
—
1.65
—
V
Input Range 1 mA
(INxRANGE = 101)
1.62
1.66
1.73
V/mA
Input Range 2 mA
(INxRANGE = 100)
810
830
855
mV/mA
Input Range 3 mA
(INxRANGE = 011)
540
550
565
mV/mA
Input Range 4 mA
(INxRANGE = 010)
400
415
425
mV/mA
Input Range 5 mA
(INxRANGE = 001)
320
330
340
mV/mA
Input Range 6 mA
(INxRANGE = 000)
265
275
285
mV/mA
—
—
500
ns
Single Conversion Time
(Default Configuration)
Maximum External Capacitive Load
Maximum External Series Impedance
CL
CL
Table 3.13. Current-to-Voltage Converter (IVC)
Parameter
Supply Voltage (VDD)
Integral Nonlinearity
Full Scale Output
Slope
Settling Time to 0.1%
20
Symbol
MIVC
Conditions
VIVCOUT
Preliminary Rev. 0.8
SiM3C1xx
Table 3.14. Voltage Reference Electrical Characteristics
VDD = 1.8 to 3.6 V, –40 to +85 °C unless otherwise specified.
Parameter
Symbol
Conditions
Min
Typ
Max
Units
VREFFS
–40 to +85 °C,
VDD = 1.8–3.6 V
1.62
1.65
1.68
V
TCREFFS
—
50
—
ppm/°C
tREFFS
—
—
1.5
µs
PSRRREFFS
—
400
—
ppm/V
VREF2X = 0
1.8
—
3.6
V
VREF2X = 1
2.7
—
3.6
V
25 °C ambient,
VREF2X = 0
1.195
1.2
1.205
V
25 °C ambient,
VREF2X = 1
2.39
2.4
2.41
V
ISC
—
—
10
mA
Temperature Coefficient
TCVREFP
—
25
—
ppm/°C
Load Regulation
LRVREFP
Load = 0 to 200 µA to
VREFGND
—
4.5
—
ppm/µA
Load Capacitor
CVREFP
Load = 0 to 200 µA to
VREFGND
0.1
—
—
µF
tVREFPON
4.7 µF tantalum, 0.1 µF
ceramic bypass
—
3.8
—
ms
0.1 µF ceramic bypass
—
200
—
µs
VREF2X = 0
—
320
—
ppm/V
VREF2X = 1
—
560
—
ppm/V
Sample Rate = 250 ksps;
VREF = 3.0 V
—
5.25
—
µA
Internal Fast Settling Reference
Output Voltage
Temperature Coefficient
Turn-on Time
Power Supply Rejection
On-Chip Precision Reference (VREF0)
Valid Supply Range
Output Voltage
Short-Circuit Current
Turn-on Time
Power Supply Rejection
VDD
VREFP
PSRRVREFP
External Reference
Input Current
IEXTREF
Preliminary Rev. 0.8
21
SiM3C1xx
Table 3.15. Temperature Sensor
Parameter
Symbol
Conditions
Min
Typ
Max
Units
Offset
VOFF
TA = 0 °C
—
760
—
mV
Offset Error*
EOFF
TA = 0 °C
—
±14
—
mV
Slope
M
—
2.8
—
mV/°C
Slope Error*
EM
—
TBD
—
µV/°C
Linearity
—
1
—
°C
Turn-on Time
—
1.8
—
µs
*Note: Represents one standard deviation from the mean.
22
Preliminary Rev. 0.8
SiM3C1xx
Table 3.16. Comparator
Parameter
Symbol
Conditions
Min
Typ
Max
Units
Response Time, CMPMD = 00
(Highest Speed)
tRESP0
+100 mV Differential
—
100
—
ns
–100 mV Differential
—
150
—
ns
Response Time, CMPMD = 11
(Lowest Power)
tRESP3
+100 mV Differential
—
1.4
—
µs
–100 mV Differential
—
3.5
—
µs
CMPHYP = 00
—
0.37
—
mV
CMPHYP = 01
—
7.9
—
mV
CMPHYP = 10
—
16.7
—
mV
CMPHYP = 11
—
32.8
—
mV
CMPHYN = 00
—
0.37
—
mV
CMPHYN = 01
—
–7.9
—
mV
CMPHYN = 10
—
–16.1
—
mV
CMPHYN = 11
—
–32.7
—
mV
CMPHYP = 00
—
0.47
—
mV
CMPHYP = 01
—
5.85
—
mV
CMPHYP = 10
—
12
—
mV
CMPHYP = 11
—
24.4
—
mV
CMPHYN = 00
—
0.47
—
mV
CMPHYN = 01
—
–6.0
—
mV
CMPHYN = 10
—
–12.1
—
mV
CMPHYN = 11
—
–24.6
—
mV
CMPHYP = 00
—
0.66
—
mV
CMPHYP = 01
—
4.55
—
mV
CMPHYP = 10
—
9.3
—
mV
CMPHYP = 11
—
19
—
mV
CMPHYN = 00
—
0.6
—
mV
CMPHYN = 01
—
–4.5
—
mV
CMPHYN = 10
—
–9.5
—
mV
CMPHYN = 11
—
–19
—
mV
Positive Hysterisis
Mode 0 (CPMD = 00)
Negative Hysterisis
Mode 0 (CPMD = 00)
Positive Hysterisis
Mode 1 (CPMD = 01)
Negative Hysterisis
Mode 1 (CPMD = 01)
Positive Hysterisis
Mode 2 (CPMD = 10)
Negative Hysterisis
Mode 2 (CPMD = 10)
HYSCP+
HYSCP-
HYSCP+
HYSCP-
HYSCP+
HYSCP-
Preliminary Rev. 0.8
23
SiM3C1xx
Table 3.16. Comparator (Continued)
Parameter
Positive Hysterisis
Mode 3 (CPMD = 11)
Negative Hysterisis
Mode 3 (CPMD = 11)
Symbol
Conditions
Min
Typ
Max
Units
HYSCP+
CMPHYP = 00
—
1.37
—
mV
CMPHYP = 01
—
3.8
—
mV
CMPHYP = 10
—
7.8
—
mV
CMPHYP = 11
—
15.6
—
mV
CMPHYN = 00
—
1.37
—
mV
CMPHYN = 01
—
–3.9
—
mV
CMPHYN = 10
—
–7.9
—
mV
CMPHYN = 11
—
–16
—
mV
–0.25
—
VDD+0.25
V
PB2 Pins
—
7.5
—
pF
PB3 Pins
—
10.5
—
pF
HYSCP-
Input Range (CP+ or CP–)
VIN
Input Pin Capacitance
CCP
Common-Mode Rejection Ratio
CMRRCP
—
75
—
dB
Power Supply Rejection Ratio
PSRRCP
—
72
—
dB
–5
0
5
mV
—
3.5
—
µV/°C
Input Offset Voltage
VOFF
Input Offset Tempco
TCOFF
Reference DAC Resolution
24
TA = 25 °C
NBits
6
Preliminary Rev. 0.8
bits
SiM3C1xx
Table 3.17. Port I/O
Parameter
Symbol
Conditions
Min
Typ
Max
Units
Low Drive, IOH = –2 mA
VIO – 0.7
—
—
V
High Drive, IOH = –5 mA
VIO – 0.7
—
—
V
Low Drive, IOL = 3 mA
—
—
0.6
V
High Drive,
IOL = 12.5 mA
—
—
0.6
V
Standard I/O (PB0, PB1, and PB2) and 5 V Tolerant I/O (PB3)
Output High Voltage
Output Low Voltage
VOH
VOL
Output Rise Time
tR
C = TBD
TBD
—
TBD
ns
Output Fall Time
tF
C = TBD
TBD
—
TBD
ns
VIH
1.8 <= VIO <= 2.0
0.7 x VIO
—
—
V
2.0 <= VIO <= 3.6
VIO – 0.6
—
—
V
—
—
0.6
V
PB0, PB1 and PB2 Pins
—
4
—
pF
PB3 Pins
—
7
—
pF
VIO = 1.8
–6
–3.5
–2
µA
VIO = 3.6
–30
–20
–10
µA
Input High Voltage
Input Low Voltage
VIL
Pin Capacitance
CIO
Weak Pull-Up Current
(Input Voltage = 0 V)
IPU
Input Leakage 
(Pullups off or Analog)
ILK
0 < VIN < VIO
–1
—
1
µA
Input Leakage Current of Port
Bank 3 I/O, VIN above VIO
IL
VIO < VIN < VIO+2.0 V
(pins without EXREG
functions)
0
5
150
µA
VIO < VIN < VREGIN
(pins with EXREG
functions)
0
5
150
µA
Standard Mode, Low
Drive, IOH = -3mA
VIOHD – 0.7
—
—
V
Standard Mode, High
Drive, IOH = -10mA
VIOHD – 0.7
—
—
V
Standard Mode, Low
Drive, IOH = 3mA
—
—
0.6
V
Standard Mode, High
Drive, IOH = 12.5mA
—
—
0.6
V
Slew Rate Mode 0,
VIOHD = 5V
—
50
—
ns
Slew Rate Mode 1,
VIOHD = 5V
—
300
—
ns
Slew Rate Mode 2,
VIOHD = 5V
—
1
—
µs
Slew Rate Mode 3,
VIOHD = 5V
—
3
—
µs
High Drive I/O (PB4)
Output High Voltage
Output Low Voltage
Output Rise Time
VOH
VOL
tR
Preliminary Rev. 0.8
25
SiM3C1xx
Table 3.17. Port I/O (Continued)
Parameter
Output Fall Time
Input High Voltage
Symbol
Conditions
Min
Typ
Max
Units
tF
Slew Rate Mode 0,
VIOHD = 5V
—
50
—
ns
Slew Rate Mode 1,
VIOHD = 5V
—
300
—
ns
Slew Rate Mode 2,
VIOHD = 5V
—
1
—
µs
Slew Rate Mode 3,
VIOHD = 5V
—
3
—
µs
—
—
V
VIOHD – 0.6
—
—
V
—
—
0.6
V
Mode 0
—
1.76
—
mA
Mode 1
—
2.34
—
Mode 2
—
3.52
—
Mode 3
—
4.69
—
Mode 4
—
7.03
—
Mode 5
—
9.38
—
Mode 6
—
14.06
—
Mode 7
—
18.75
—
Mode 8
—
28.13
—
Mode 9
—
37.5
—
Mode 10
—
56.25
—
Mode 11
—
75
—
Mode 12
—
112.5
—
Mode 13
—
150
—
Mode 14
—
225
—
Mode 15
—
300
—
—
—
400
VIH
1.8 V<= VIOHD <= 2.0 V 0.7 x VIOHD
2.0 V<= VIOHD <= 6 V
Input Low Voltage
N-Channel Sink Current Limit
(2.7 V <= VIOHD <= 6 V,
VOL = 0.8V)
Total N-Channel Sink Current on
P4.0-P4.5 (DC)
26
VIL
ISINKL
ISINKLT
Preliminary Rev. 0.8
mA
SiM3C1xx
Table 3.17. Port I/O (Continued)
Parameter
Symbol
Conditions
Min
Typ
Max
Units
ISRCL
Mode 0
—
0.88
—
mA
Mode 1
—
1.17
—
Mode 2
—
1.76
—
Mode 3
—
2.34
—
Mode 4
—
3.52
—
Mode 5
—
4.69
—
Mode 6
—
7.03
—
Mode 7
—
9.38
—
Mode 8
—
14.06
—
Mode 9
—
18.75
—
Mode 10
—
28.13
—
Mode 11
—
37.5
—
Mode 12
—
56.25
—
Mode 13
—
75
—
Mode 14
—
112.5
—
Mode 15
—
150
—
ISRCLT
—
—
400
mA
Pin Capacitance
CIO
—
30
—
pF
Weak Pull-Up Current in Low Voltage Mode
IPU
VIOHD = 1.8 V
–6
–3.5
–2
µA
VIOHD = 3.6 V
–30
–20
–10
µA
VIOHD = 2.7 V
–15
–10
–5
µA
VIOHD = 6 V
–30
–20
–10
µA
–1
—
1
µA
P-Channel Source Current Limit
(2.7 V <= VIOHD <= 6 V,
VOH = VIOHD - 0.8V)
Total P-Channel Source Current on
P4.0-P4.5 (DC)
Weak Pull-Up Current in High Voltage Mode
Input Leakage (Pullups off)
IPU
ILK
Preliminary Rev. 0.8
27
SiM3C1xx
3.2. Thermal Conditions
Table 3.18. Thermal Conditions
Parameter
Symbol
Conditions
Min
Typ
Max
Units
JA
LGA-92 Packages
—
35
—
°C/W
TQFP-80 Packages
—
40
—
°C/W
QFN-64 Packages
—
25
—
°C/W
TQFP-64 Packages
—
30
—
°C/W
QFN-40 Packages
—
30
—
°C/W
Thermal Resistance*
*Note: Thermal resistance assumes a multi-layer PCB with any exposed pad soldered to a PCB pad.
3.3. Absolute Maximum Ratings
Stresses above those listed under Table 3.19 may cause permanent damage to the device. This is a stress rating
only and functional operation of the devices at those or any other conditions above those indicated in the operation
listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect
device reliability.
Table 3.19. Absolute Maximum Ratings
Parameter
Symbol
Conditions
Min
Max
Units
Ambient Temperature Under Bias
TBIAS
–55
125
°C
Storage Temperature
TSTG
–65
150
°C
Voltage on VDD
VDD
VSS–0.3
4.2
V
EXTVREG0 Not Used
VSS–0.3
6.0
V
EXTVREG0 Used
VSS–0.3
3.6
V
VIO
VSS–0.3
4.2
V
VIOHD
VSS–0.3
6.5
V
RESET, VIO > 3.3 V
VSS–0.3
5.8
V
RESET, VIO < 3.3 V
VSS–0.3
VIO+2.5
V
Port Bank 0, 1, and 2 I/O
VSS–0.3
VIO+0.3
V
Port Bank 4 I/O
VSSHD–0.3
VIOHD+0.3
V
Voltage on VREGIN
Voltage on VIO
Voltage on VIOHD
Voltage on I/O pins, non Port Bank 3 I/
O
VREGIN
VIN
*Note: VSS and VSSHD provide separate return current paths for device supplies, but are not isolated. They must always be
connected to the same potential on board.
28
Preliminary Rev. 0.8
SiM3C1xx
Table 3.19. Absolute Maximum Ratings (Continued)
Parameter
Voltage on I/O pins, Port Bank 3 I/O
Symbol
Conditions
Min
Max
Units
VIN
SiM3C1x7, PB3.0–
PB3.7, VIO > 3.3 V
VSS–0.3
5.8
V
SiM3C1x7, PB3.0–
PB3.7, VIO < 3.3 V
VSS–0.3
VIO+2.5
V
SiM3C1x7, PB3.8 PB3.11
VSS–0.3
Lowest of
VIO+2.5,
VREGIN+0.3,
or 5.8
V
SiM3C1x6, PB3.0–
PB3.5, VIO > 3.3 V
VSS–0.3
5.8
V
SiM3C1x6, PB3.0–
PB3.5, VIO < 3.3 V
VSS–0.3
VIO+2.5
V
SiM3C1x6, PB3.6–
PB3.9
VSS–0.3
Lowest of
VIO+2.5,
VREGIN+0.3,
or 5.8
V
SiM3C1x4, PB3.0–
PB3.3
VSS–0.3
Lowest of
VIO+2.5,
VREGIN+0.3,
or 5.8
V
Total Current Sunk into Supply Pins
ISUPP
VDD, VREGIN, VIO, VIOHD
—
400
mA
Total Current Sourced out of Ground
Pins
IVSS
VSS, VSSHD
400
—
mA
Current Sourced or Sunk by Any I/O
Pin
IPIO
PB0, PB1, PB2, PB3,
and RESET
–100
100
mA
PB4
–300
300
mA
PB0, PB1, PB2, PB3,
and RESET
–100
100
mA
PB4
–300
300
mA
Sum of all I/O and
RESET
–400
400
mA
Current Injected on Any I/O Pin
Total Injected Current on I/O Pins
IINJ
IINJ
*Note: VSS and VSSHD provide separate return current paths for device supplies, but are not isolated. They must always be
connected to the same potential on board.
Preliminary Rev. 0.8
29
SiM3C1xx
Table 3.19. Absolute Maximum Ratings (Continued)
Parameter
Power Dissipation at TA = 85 °C
Symbol
Conditions
Min
Max
Units
PD
LGA-92 Package
—
570
mW
TQFP-80 Package
—
500
mW
QFN-64 Package
—
800
mW
TQFP-64 Package
—
650
mW
QFN-40 Package
—
650
mW
*Note: VSS and VSSHD provide separate return current paths for device supplies, but are not isolated. They must always be
connected to the same potential on board.
30
Preliminary Rev. 0.8
SiM3C1xx
4. Precision32™ SiM3C1xx System Overview
The SiM3C1xx Precision32™ devices are fully integrated, mixed-signal system-on-a-chip MCUs. Highlighted
features are listed below. Refer to Table 6.1 for specific product feature selection and part ordering numbers.
Core:
32-bit
ARM Cortex-M3 CPU.
MHz maximum operating frequency.
Branch target cache and prefetch buffers to minimize wait states.
80
Memory:
32–256 kB Flash; in-system programmable, 8–32 kB SRAM (including 4 kB retention SRAM,
which preserves state in PM9 mode).
Power:
Low
drop-out (LDO) regulator for CPU core voltage.
reset circuit and brownout detectors.
3.3 V output LDO for direct power from 5 V supplies.
External transistor regulator.
Power Management Unit (PMU).
Power-on
I/O:
Up to 65 total multifunction I/O pins:
Up
to six programmable high-power capable (5–300 mA, 1.8–5 V).
to twelve 5 V tolerant general purpose pins.
Two flexible peripheral crossbars for peripheral routing.
Up
Clock
Sources:
oscillator with PLL: 23–80 MHz with ± 1.5% accuracy in free-running mode.
Low-power internal oscillator: 20 MHz and 2.5 MHz modes.
Low-frequency internal oscillator: 16.4 kHz.
External RTC crystal oscillator: 32.768 kHz.
External oscillator: Crystal, RC, C, CMOS clock modes.
Programmable clock divider allows any oscillator source to be divided by binary factor from 1-128.
Internal
Data
Peripherals:
16-Channel
DMA Controller.
Hardware AES Encryption.
16/32-bit CRC.
128/192/256-bit
Timers/Counters
and PWM:
6-channel
Enhanced Programmable Counter Array (EPCAn) supporting advanced PWM and capture/compare.
x 2-channel Standard Programmable Counter Array (PCAn) supporting PWM and capture/compare.
2 x 32-bit Timers - can be split into 4 x 16-bit Timers, support PWM and capture/compare.
Real Time Clock (RTCn).
Low Power Timer.
Watchdog Timer.
2
Communications
Peripherals:
External
Memory Interface.
2 x USARTs and 2 x UARTs with IrDA and ISO7816 SmartCard support.
3 x SPIs.
2 x I2C.
I
2S
(receive and transmit).
Analog:
2
x 12-Bit Analog-to-Digital Converters (SARADC).
x 10-Bit Digital-to-Analog Converter (IDAC).
16-Channel Capacitance-to-Digital Converter (CAPSENSE).
2 x Low-Current Comparators (CMP).
1 x Current-to-Voltage Converter (IVC) module with two channels.
2
On-Chip
Debugging
With on-chip power-on reset, voltage supply monitor, watchdog timer, and clock oscillator, the SiM3C1xx devices
are truly standalone system-on-a-chip solutions. The Flash memory is reprogrammable in-circuit, providing non-
Preliminary Rev. 0.8
31
SiM3C1xx
volatile data storage and allowing field upgrades of the firmware. User firmware has complete control of all
peripherals and may individually shut down and gate the clocks of any or all peripherals for power savings.
The on-chip debugging interface (SWJ-DP) allows non-intrusive (uses no on-chip resources), full speed, in-circuit
debugging using the production MCU installed in the final application. This debug logic supports inspection and
modification of memory and registers, setting breakpoints, single stepping, and run and halt commands. All analog
and digital peripherals are fully functional while debugging.
Each device is specified for 1.8 to 3.6 V operation over the industrial temperature range (–40 to +85 °C). The Port
I/O and RESET pins are powered from the IO supply voltage. The SiM3C1xx devices are available in 40-pin or 64pin QFN, 64-pin or 80-pin TQFP, or 92-pin LGA packages. All package options are lead-free and RoHS compliant.
See Table 6.1 for ordering information. A block diagram is included in Figure 4.1.
Analog
Core
ARM Cortex M3
Power On Reset /
PMU
APB
Debug /
Programming
Hardware
AHB
Watchdog
Timer
(WDTIMER0)
SARADC0
SARADC1
IDAC0
IDAC1
Comparator 0 Comparator 1
Memory
Voltage Supply
Monitor (VMON0)
32/64/128/256 kB Flash
IVC0
Capacitive Sensing 0
4/12/28 kB RAM
Power
I/O
4 kB retention RAM
EMIF
Low Dropout Regulator (LDO0)
Voltage Regulator (VREG0)
DMA
Crossbars
External Regulator (EXTVREG0)
16-Channel Controller
Standard I/O pins
Power Management Unit (PMU)
Peripheral Crossbar
5 V tolerant pins
High Drive pins
Clocking
Digital
Real-Time Clock (RTC0OSC)
USART0
USART1
UART0
UART1
Low Frequency Oscillator (LFOSC0)
SPI0
SPI1
SPI2
Low Power Oscillator (LPOSC0)
External Oscillator Control (EXTOSC0)
Clock Control
I2C0
I2C1
I2S0
Phase-Locked Loop (PLL0OSC)
EPCA0
PCA0
PCA1
Peripheral Clock Control (CLKCTRL)
AES0
CRC0
Timer 0
Timer 1
Low Power Timer (LPTIMER0)
DMA access available for these peripherals
Figure 4.1. Precision32™ SiM3C1xx Family Block Diagram
32
Preliminary Rev. 0.8
SiM3C1xx
4.1. Power
4.1.1. LDO and Voltage Regulator (VREG0)
The SiM3C1xx devices include two internal regulators: the core LDO Regulator and the Voltage Regulator
(VREG0).
The LDO Regulator converts a 1.8–3.6 V supply to the core operating voltage of 1.8 V. This LDO consumes little
power and provides flexibility in choosing a power supply for the system.
The Voltage Regulator regulates from 5.5 to 2.7 V and can serve as an input to the LDO. This allows the device to
be powered from up to a 5.5 V supply without any external components other than bypass capacitors.
4.1.2. Voltage Supply Monitor (VMON0)
The SiM3C1xx devices include a voltage supply monitor which allows devices to function in known, safe operating
condition without the need for external hardware. The supply monitor includes additional circuitry that can monitor
the main supply voltage and the VREGIN input voltage divided by 4 (VREGIN / 4).
The supply monitor module includes the following features:
Main
supply “VDD Low” (VDD below the early warning threshold) notification.
the device in reset if the main VDD supply drops below the VDD Reset threshold.
VREGIN divided by 4 (VREGIN / 4) supply “VREGIN Low” notification.
Holds
4.1.3. External Regulator (EXTVREG0)
The External Regulator provides all the circuitry needed for a high-power regulator except the power transistor
(NPN or PNP) and current sensing resistor (if current limiting is enabled).
The External Regulator module has the following features:
Interfaces
with either an NPN or PNP external transistor that serves as the pass device for the high current
regulator.
Automatic current limiting.
Automatic foldback limiting.
Sources up to 1 A for use by external circuitry.
Variable output voltage from 1.8–3.6 V in 100 mV steps.
4.1.4. Power Management Unit (PMU)
The Power Management Unit on the SiM3C1xx manages the power systems of the device. On power-up, the PMU
ensures the core voltages are a proper value before core instruction execution begins. It also recognizes and
manages the various wake sources for low-power modes of the device.
The PMU module includes the following features:
Up
to 16 pin wake inputs can wake the device from Power Mode 9.
Low Power Timer, RTC0 (alarms and oscillator fail), Comparator 0, and the RESET pin can also serve
as wake sources for Power Mode 9.
All PM9 wake sources (except for the RESET pin) can also reset the Low Power Timer or RTC0 modules.
Disables the level shifters to pins and peripherals to further reduce power usage in PM9. These level
shifters must be re-enabed by firmware after exiting PM9.
Provides a PMU_Asleep signal to a pin as an indicator that the device is in PM9.
The
Preliminary Rev. 0.8
33
SiM3C1xx
4.1.5. Device Power Modes
The SiM3C1xx devices feature four low power modes in addition to normal operating mode. Several peripherals
provide wake up sources for these low power modes, including the Low-Power Timer (LPT0), RTC0 (alarms and
oscillator failure notification), Comparator 0, and PMU Pin Wake. All power modes are detailed in Table 4.1.
Table 4.1. SiM3C1xx Power Modes
Mode
Description
Mode Entrance
Mode Exit
Execute code from RAM
Jump to code in Flash
WFI or WFE instruction
NVIC or WIC wakeup
Core
Normal
operating at full
speed
Code executing from
Flash
Core
Power Mode 1
(PM1)
operating at full
speed
Code executing from
RAM
Core
Power Mode 2
(PM2)
halted
AHB and APB operate
at full speed for
peripherals
All
Power Mode 3
Fast Wake
(PM3FW)
clocks stopped
except LFOSC0 or
RTC0OSC
AHB and APB set to
Low Power Oscillator
Core clock set to
LFOSC0 or RTC0OSC
DMACTRL0
disabled
wake mode
enabled in PM3CN
AHB switched to
Low Power
Oscillator
WFI or WFE
instruction
Fast
NVIC or WIC wakeup
DMACTRL0
Power Mode 3
(PM3)
All clocks stopped
disabled
Clocks disabled in
PM3CN
WFI or WFE
instruction
NVIC or WIC wakeup
SLEEPDEEP
Power Mode 9
(PM9)
Low power shutdown
set in
the ARM System
Requires a reset defined by
Control Register
the PMU as a wake up
source
WFI or WFE
instruction
In addition, all peripherals can have their clocks disconnected to reduce power consumption whenever a peripheral
is not being used using the clock control (CLKCTRL) registers.
34
Preliminary Rev. 0.8
SiM3C1xx
4.1.5.1. Normal Mode
Normal mode encompasses the typical full-speed operation. The power consumption of the device in this mode will
vary depending on AHB/APB clock speeds and the settings of CLKCTRL and the peripherals.
4.1.5.2. Power Mode 1
Power Mode 1 occurs when the core executes code from RAM instead of Flash. The power consumption of the
device is slightly less than normal mode when in PM1.
4.1.5.3. Power Mode 2
In Power Mode 2, the core halts and the peripherals run at full speed. To place the device in this mode, the clock
settings in CLKCTRL should remain the same as Normal or Power Mode 1 and the core should execute a wait-forinterrupt (WFI) or wait-for-event (WFE) instruction. If the WFI instruction is called from an interrupt service routine,
the interrupt that wakes the device from PM2 must be of a sufficient priority to be recognized by the core.
4.1.5.4. Power Mode 3 Fast Wake
Power Mode 3 Fast Wake occurs when all the clocks are stopped except for the LFOSC0 or RTC0OSC. The core
and the peripherals are halted in this mode.
The following sequence places the device in Power Mode 3 Fast Wake:
1. All DMA channels must be disabled by using the global enable/disable DMAEN in the DMA Controller
(DMACTRL0).
2. Firmware should enable PM3 Fast Wake in the PM3CN register and set the core clock to run off of the
LFOSC0 or RTC0OSC to achieve the lowest power.
3. CLKCTRL CONTROL register settings must be modified to set the AHB and APB clocks to the Low Power
Oscillator.
4. Firmware should then execute a WFI or WFE instruction.
If the WFI instruction is called from an interrupt service routine, the interrupt that wakes the device from PM3FW
must be of a sufficient priority to be recognized by the core.
By keeping the core clock running at a slow frequency in PM3 and changing the AHB and APB clocks to the Low
Power Oscillator, the device can wake up faster than in standard Power Mode 3 at the expense of higher power
consumption.
4.1.5.5. Power Mode 3
Power Mode 3 occurs when all the clocks are stopped, and the core and the peripherals are halted.
The following sequence places the device in Power Mode 3:
1. All DMA channels must be disabled by using the global enable/disable DMAEN in the DMA Controller
(DMACTRL0).
2. Firmware should disable PM3 Fast Wake in the PM3CN register.
3. Firmware should then execute a WFI or WFE instruction.
If the WFI instruction is called from an interrupt service routine, the interrupt that wakes the device from PM3 must
be of a sufficient priority to be recognized by the core.
4.1.5.6. Power Mode 9
In Power Mode 9, the core and all peripherals are halted, all clocks are stopped, and the pins and peripherals are
set to a lower power mode. In addition, standard RAM contents are not preserved, though retention RAM contents
are still available after exiting the power mode. This mode provides the lowest power consumption for the device,
but requires an appropriate reset to exit. The available reset sources to wake from PM9 are controlled by the
Power Management Unit (PMU).
To enter this mode, firmware must write the SLEEPDEEP bit in the ARM System Control Register. Firmware must
then execute a WFI or WFE instruction. The core will remain in PM9 until an enabled reset source occurs.
Preliminary Rev. 0.8
35
SiM3C1xx
4.2. I/O
4.2.1. General Features
The SiM3C1xx ports have the following features:
Push-pull
or open-drain output modes and analog or digital modes.
Option for high or low output drive strength.
Port Match allows the device to recognize a change on a port pin value.
Internal pull-up resistors are enabled or disabled on a port-by-port basis.
Two external interrupts with up to 16 inputs provide monitoring capability for external signals.
Internal Pulse Generator Timer (PB2 only) to generate simple square waves.
A subset of pins can also serve as inputs to the Port Mapped Level Shifters available on the High Drive
Pins.
4.2.2. High Drive Pins (PB4)
The High Drive pins have the following additional features:
Programmable
safe state: high, low, or high impedance.
Programmable drive strength and slew rates.
Programmable current limiting.
Powered from a separate source (VIOHD, which can be up to 6 V) from the rest of the device.
Supports various functions, including GPIO, UART1 pins, EPCA0 pins, or Port Mapped Level Shifting.
4.2.3. 5 V Tolerant Pins (PB3)
The 5 V tolerant pins can be connected to external circuitry operating at voltages above the device supply without
needing extra components to shift the voltage level.
4.2.4. Crossbars
The SiM3C1xx devices have two Crossbars with the following features:
Flexible
peripheral assignment to port pins.
Pins can be individually skipped to move peripherals as needed for design or layout considerations.
The Crossbars have a fixed priority for each I/O function and assign these functions to the port pins. When a digital
resource is selected, the least-significant unassigned port pin is assigned to that resource. If a port pin is assigned,
the Crossbars skip that pin when assigning the next selected resource. Additionally, the Crossbars will skip port
pins whose associated bits in the PBSKIPEN registers are set. This provides some flexibility when designing a
system: pins involved with sensitive analog measurements can be moved away from digital I/O and peripherals
can be moved around the chip as needed to ease layout constraints.
36
Preliminary Rev. 0.8
SiM3C1xx
4.3. Clocking
The SiM3C1xx devices have two system clocks: AHB and APB. The AHB clock services memory peripherals and
is derived from one of seven sources: the RTC0 Oscillator, the Low Frequency Oscillator, the Low Power Oscillator,
the divided Low Power Oscillator, the External Oscillator, and the PLL0 Oscillator. In addition, a divider for the AHB
clock provides flexible clock options for the device. The APB clock services data peripherals and is synchronized
with the AHB clock. The APB clock can be equal to the AHB clock (if AHB is less than or equal to 50 MHz) or set to
the AHB clock divided by two.
Clock Control allows the AHB and APB clocks to be turned off to unused peripherals to save system power. Any
registers in a peripheral with disabled clocks will be unable to be accessed until the clocks are enabled. Most
peripherals have clocks off by default after a power-on reset.
Clock Control
RTC0
Oscillator
RAM
DMA
LFOSC0
AHB clock
Flash
LPOSC0
AHB Clock
Divider
EMIF
PLL0 Registers
External
Oscillator
PLL0
Oscillator
PBCFG and
PB0/1/2/3/4
APB Clock
Divider
APB clock
USART0
USART1
UART0
Preliminary Rev. 0.8
37
SiM3C1xx
4.3.1. PLL (PLL0)
The PLL module consists of a dedicated Digitally-Controlled Oscillator (DCO) that can be used in Free-Running
mode without a reference frequency, Frequency-Locked to a reference frequency, or Phase-Locked to a reference
frequency. The reference frequency for Frequency-Lock and Phase-Lock modes can use one of multiple sources
(including the external oscillator) to provide maximum flexibility for different application needs. Because the PLL
module generates its own clock, the DCO can be locked to a particular reference frequency and then moved to
Free-Running mode to reduce system power and noise.
The PLL module includes the following features:
Five
output ranges with output frequencies ranging from 23 to 80 MHz.
Multiple reference frequency inputs.
Three output modes: free-running DCO, frequency-locked, and phase-locked.
Ability to sense the rising edge or falling edge of the reference source.
DCO frequency LSB dithering to provide finer average output frequencies.
Spectrum spreading to reduce generated system noise.
Low jitter and fast lock times.
Ability to suspend all output frequency updates (including dithering and spectrum spreading) using the
STALL bit during jitter-sensitive operations.
4.3.2. Low Power Oscillator (LPOSC0)
The Low Power Oscillator is the default AHB oscillator on SiM3C1xx devices and enables or disables
automatically, as needed.
The Low Power Oscillator has the following features:
20
MHz and divided 2.5 MHz frequencies available for the AHB clock.
starts and stops as needed.
Automatically
4.3.3. Low Frequency Oscillator (LFOSC0)
The low frequency oscillator (LFOSC0) provides a low power internal clock source running at approximately
16.4 kHz for the RTC0 timer and other peripherals on the device. No external components are required to use the
low frequency oscillator
4.3.4. External Oscillators (EXTOSC0)
The EXTOSC0 external oscillator circuit may drive an external crystal, ceramic resonator, capacitor, or RC
network. A CMOS clock may also provide a clock input. The external oscillator output may be selected as the AHB
clock or used to clock other modules independent of the AHB clock selection.
The External Oscillator control has the following features:
Support
for external crystal, RC, C, or CMOS oscillators.
external CMOS frequencies from 10 kHz to 50 MHz and external crystal frequencies from 10 kHz
to 30 MHz.
Various drive strengths for flexible crystal oscillator support.
Internal frequency divide-by-two option available.
Support
38
Preliminary Rev. 0.8
SiM3C1xx
4.4. Data Peripherals
4.4.1. 16-Channel DMA Controller
The DMA facilitates autonomous peripheral operation, allowing the core to finish tasks more quickly without
spending time polling or waiting for peripherals to interrupt. This helps reduce the overall power consumption of the
system, as the device can spend more time in low-power modes.
The DMA controller has the following features:
Utilizes
ARM PrimeCell uDMA architecture.
16 channels.
DMA crossbar supports SARADC0, SARADC1, IDAC0, IDAC1, I2C0, I2S0, SPI0, SPI1, USART0,
USART1, AES0, EPCA0, external pin triggers, and timers.
Supports primary, alternate, and scatter-gather data structures to implement various types of transfers.
Access allowed to all AHB and APB memory space.
Implements
4.4.2. 128/192/256-bit Hardware AES Encryption (AES0)
The basic AES block cipher is implemented in hardware. The integrated hardware support for Cipher Block
Chaining (CBC) and Counter (CTR) algorithms results in identical performance, memory bandwidth, and memory
footprint between the most basic Electronic Codebook (ECB) algorithm and these more complex algorithms. This
hardware accelerator translates to more core bandwidth available for other functions or a power savings for lowpower applications.
The AES module includes the following features:
Operates
on 4-word (16-byte) blocks.
key sizes of 128, 192, and 256 bits for both encryption and decryption.
Generates the round key for decryption operations.
All cipher operations can be performed without any firmware intervention for a set of 4-word blocks (up to
32 kB).
Support for various chained and stream-ciphering configurations with XOR paths on both the input and
output.
Internal 4-word FIFOs to facilitate DMA operations.
Integrated key storage.
Hardware acceleration for Cipher-Block Chaining (CBC) and Counter (CTR) algorithms utilizing integrated
counterblock generation and previous-block caching.
Supports
4.4.3. 16/32-bit CRC (CRC0)
The CRC module is designed to provide hardware calculations for Flash memory verification and communications
protocols.
The CRC module supports four common polynomials. The supported 32-bit polynomial is 0x04C11DB7 (IEEE
802.3). The three supported 16-bit polynomials are 0x1021 (CCITT-16), 0x3D65 (IEC16-MBus), and 0x8005
(ZigBee, 802.15.4, and USB).
The CRC module includes the following features:
Support
for four common polynomials (one 32-bit and three 16-bit options).
Byte-level bit reversal for the CRC input.
Byte-order reorientation of words for the CRC input.
Word or half-word bit reversal of the CRC result.
Ability to configure and seed an operation in a single register write.
Support for single-cycle parallel (unrolled) CRC computation for 32- or 8-bit blocks.
Capability to CRC 32 bits of data per peripheral bus (APB) clock.
Support for DMA writes using firmware request mode.
Preliminary Rev. 0.8
39
SiM3C1xx
4.5. Counters/Timers and PWM
4.5.1. Programmable Counter Array (EPCA0, PCA0, PCA1)
The SiM3C1xx devices include two types of PCA module: Enhanced and Standard.
The Enhanced Programmable Counter Array (EPCA0) and Standard Programmable Counter Array (PCA0, PCA1)
modules are timer/counter systems allowing for complex timing or waveform generation. Multiple modules run from
the same main counter, allowing for synchronous output waveforms.
The Enhanced PCA module is multi-purpose, but is optimized for motor control applications. The EPCA module
includes the following features:
Three
sets of channel pairs (six channels total) capable of generating complementary waveforms.
and edge-aligned waveform generation.
Programmable dead times that ensure channel pairs are never both active at the same time.
Programmable clock divisor and multiple options for clock source selection.
Waveform update scheduling.
Option to function while the core is inactive.
Multiple synchronization triggers and outputs.
Pulse-Width Modulation (PWM) waveform generation.
High-speed square wave generation.
Input capture mode.
DMA capability for both input capture and waveform generation.
PWM generation halt input.
The Standard PCA module (PCA) includes the following features:
Center-
Two
independent channels.
Center- and edge-aligned waveform generation.
Programmable clock divisor and multiple options for clock source selection.
Pulse-Width Modulation waveform generation.
4.5.2. 32-bit Timer (TIMER0, TIMER1)
Each timer module is independent, and includes the following features:
Operation
as a single 32-bit or two independent 16-bit timers.
Clocking options include the APB clock, the APB clock scaled using an 8-bit prescaler, the external
oscillator, or falling edges on an external input pin (synchronized to the APB clock).
Auto-reload functionality in both 32-bit and 16-bit modes.
Up/Down count capability, controlled by an external input pin.
Rising and falling edge capture modes.
Low or high pulse capture modes.
Duty cycle capture mode.
Square wave output mode, which is capable of toggling an external pin at a given rate with 50% duty cycle.
32- or 16-bit pulse-width modulation mode.
40
Preliminary Rev. 0.8
SiM3C1xx
4.5.3. Real-Time Clock (RTC0)
The RTC0 module includes a 32-bit timer that allows up to 36 hours of independent time-keeping when used with a
32.768 kHz watch crystal. The RTC0 provides three alarm events in addition to a missing clock event, which can
also function as interrupt, reset, or wakeup sources on SiM3C1xx devices.
The RTC0 module includes internal loading capacitors that are programmable to 16 discrete levels, allowing
compatibility with a wide range of crystals.
The RTC0 output can be buffered and routed to a port bank pin to provide an accurate, low frequency clock to
other devices while the core is in its lowest power down mode. The module also includes a low power internal low
frequency oscillator that reduces low power mode current and is available for other modules to use as a clock
source.
The RTC module includes the following features:
32-bit
timer (supports up to 36 hours) with three separate alarms.
for one alarm to automatically reset the RTC timer.
Missing clock detector.
Can be used with the internal low frequency oscillator (LFOSC0), an external 32.768 kHz crystal (no
additional resistors or capacitors necessary), or with an external CMOS clock.
Programmable internal loading capacitors support a wide range of external 32.768 kHz crystals.
Operates directly from VDD and remains operational even when the device goes into its lowest power
down mode.
The output can be buffered and routed to an I/O pin to provide an accurate, low frequency clock to other
devices while the core is in its lowest power down mode.
Option
4.5.4. Low Power Timer (LPTIMER0)
The Low Power Timer (LPTIMER0) module runs from the clock selected by the RTC0 module, allowing the
LPTIMER0 to operate even if the AHB and APB clocks are disabled. The LPTIMER0 counter can increment using
one of two clock sources: the clock selected by the RTC0 module, or rising or falling edges of an external signal.
The Low Power Timer includes the following features:
Runs
on a low-frequency clock (RTC0OSC or LFOSC0 selected in RTC0) or an external source (rising or
falling edge).
Overflow and threshold-match detection, which can generate an interrupt, reset the timer, or wake some
devices from low power modes.
Timer reset on threshold-match allows square-wave generation at a variable output frequency.
4.5.5. Watchdog Timer (WDTIMER0)
The WDTIMER0 module includes a 16-bit timer, a programmable early warning interrupt, and a programmable
reset period. The timer registers are protected from inadvertent access by an independent lock and key interface.
The watchdog timer runs from the low frequency oscillator (LFOSC0).
The Watchdog Timer has the following features:
Programmable
timeout interval.
Optional interrupt to warn when the Watchdog Timer is nearing the reset trip value.
Lock-out feature to prevent any modification until a system reset.
Preliminary Rev. 0.8
41
SiM3C1xx
4.6. Communications Peripherals
4.6.1. External Memory Interface (EMIF0)
The External Memory Interface (EMIF0) allows external parallel asynchronous devices, like SRAMs and LCD
controllers, to appear as part of the system memory map. The EMIF0 module includes the following features:
Provides
a memory mapped view of multiple external devices.
Support for byte, half-word and word accesses regardless of external device data-width.
Error indicator for certain invalid transfers.
Minimum external timing allows for 3 clocks per write or 4 clocks per read.
Output bus can be shared between non-muxed and muxed devices.
Available extended address output allows for up to 24-bit address with 8-bit parallel devices.
Support for 8-bit and 16-bit (muxed-mode only) devices with up to two chip-select signals.
Support for internally muxed devices with dynamic address shifting.
Fully programmable control signal waveforms.
4.6.2. USART (USART0, USART1)
The USART uses two signals (TX and RX) and a predetermined fixed baud rate to communicate with a single
device. In addition to these signals, the USART0 module can optionally use a clock (UCLK) or hardware
handshaking (RTS and CTS).
The USART module provides the following features:
Independent
transmitter and receiver configurations with separate 16-bit baud rate generators.
Synchronous or asynchronous transmissions and receptions.
Clock master or slave operation with programmable polarity and edge controls.
Up to 5 Mbaud (synchronous or asynchronous, TX or RX, and master or slave) or 1 Mbaud Smartcard (TX
or RX).
Individual enables for generated clocks during start, stop, and idle states.
Internal transmit and receive FIFOs with flush capability and support for byte, half-word, and word reads
and writes.
Data bit lengths from 5 to 9 bits.
Programmable inter-packet transmit delays.
Auto-baud detection with support for the LIN SYNC byte.
Automatic parity generation (with enable).
Automatic start and stop generation (with separate enables).
Transmit and receive hardware flow-control.
Independent inversion correction for TX, RX, RTS, and CTS signals.
IrDA modulation and demodulation with programmable pulse widths.
Smartcard ACK/NACK support.
Parity error, frame error, overrun, and underrun detection.
Multi-master and half-duplex support.
Multiple loop-back modes supported.
Multi-processor communications support.
4.6.3. UART (UART0, UART1)
The USART uses two signals (TX and RX) and a predetermined fixed baud rate to communicate with a single
device.
The UART module provides the following features:
Independent
transmitter and receiver configurations with separate 16-bit baud-rate generators.
Asynchronous transmissions and receptions.
Up to 5 Mbaud (TX or RX) or 1 Mbaud Smartcard (TX or RX).
42
Preliminary Rev. 0.8
SiM3C1xx
Internal
transmit and receive FIFOs with flush capability and support for byte, half-word, and word reads
and writes.
Data bit lengths from 5 to 9 bits.
Programmable inter-packet transmit delays.
Auto-baud detection with support for the LIN SYNC byte.
Automatic parity generation (with enable).
Automatic start and stop generation.
Transmit and receive hardware flow-control.
Independent inversion correction for TX, RX, RTS, and CTS signals.
IrDA modulation and demodulation with programmable pulse widths.
Smartcard ACK/NACK support.
Parity error, frame error, overrun, and underrun detection.
Multi-master and half-duplex support.
Multiple loop-back modes supported.
4.6.4. SPI (SPI0, SPI1)
SPI is a 3- or 4-wire communication interface that includes a clock, input data, output data, and an optional select
signal.
The SPI module includes the following features:
Supports
3- or 4-wire master or slave modes.
Supports up to 10 MHz clock in master mode and 5 MHz clock in slave mode.
Support for all clock phase and slave select (NSS) polarity modes.
16-bit programmable clock rate.
Programmable MSB-first or LSB-first shifting.
8-byte FIFO buffers for both transmit and receive data paths to support high speed transfers.
Programmable FIFO threshold level to request data service for DMA transfers.
Support for multiple masters on the same data lines.
4.6.5. I2C (I2C0, I2C1)
The I2C interface is a two-wire, bi-directional serial bus. The two clock and data signals operate in open-drain
mode with external pull-ups to support automatic bus arbitration.
Reads and writes to the interface are byte oriented with the I2C interface autonomously controlling the serial
transfer of the data. Data can be transferred at up to 1/8th of the APB clock as a master or slave, which can be
faster than allowed by the I2C specification, depending on the clock source used. A method of extending the clocklow duration is available to accommodate devices with different speed capabilities on the same bus.
The I2C interface may operate as a master and/or slave, and may function on a bus with multiple masters. The I2C
provides control of SDA (serial data), SCL (serial clock) generation and synchronization, arbitration logic, and start/
stop control and generation.
The I2C module includes the following features:
Standard
(up to 100 kbps) and Fast (400 kbps) transfer speeds.
Can operate down to APB clock divided by 32768 or up to APB clock divided by 8.
Support for master, slave, and multi-master modes.
Hardware synchronization and arbitration for multi-master mode.
Clock low extending (clock stretching) to interface with faster masters.
Hardware support for 7-bit slave and general call address recognition.
Firmware support for 10-bit slave address decoding.
Ability to disable all slave states.
Programmable clock high and low period.
Programmable data setup/hold times.
Preliminary Rev. 0.8
43
SiM3C1xx
Spike
suppression up to 2 times the APB period.
4.6.6. I2S (I2S0)
The I2S module receives digital data from an external source over a data line in the standard I2S, left-justified, rightjustified, or time domain multiplexing format, de-serializes the data, and generates requests to transfer the data
using the DMA. The module also reads stereo audio samples from the DMA, serializes the data, and sends it out of
the chip on a data line in the same standard serial format for digital audio. The I2S receive interface consists of 3
signals: SCK (bit clock), WS (word select or frame sync), and SD (data input). The block’s transmit interface
consists of 3 signals: SCK (bit clock), WS (word select or frame sync) and SD (data output).
The I2S module includes the following features:
Master
or slave capability.
10-bit clock divider with 8-bit fractional clock divider provides support for various common
sampling frequencies (16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, and 48 kHz) for up to two 32-bit
channels.
Support for DMA data transfers.
Support for various data formats.
Flexible
44
Preliminary Rev. 0.8
SiM3C1xx
4.7. Analog
4.7.1. 12-Bit Analog-to-Digital Converters (SARADC0, SARADC1)
The SARADC0 and SARADC1 modules on SiM3C1xx devices are Successive Approximation Register (SAR)
Analog to Digital Converters (ADCs). The key features of the SARADC module are:
Single-ended
12-bit and 10-bit modes.
Supports an output update rate of 250 k samples per second in 12-bit mode or 1 M samples per second in
10-bit mode.
Operation in low power modes at lower conversion speeds.
Selectable asynchronous hardware conversion trigger with hardware channel select.
Output data window comparator allows automatic range checking.
Support for Burst Mode, which produces one set of accumulated data per conversion-start trigger with
programmable power-on settling and tracking time.
Conversion complete, multiple conversion complete, and FIFO overflow and underflow flags and interrupts
supported.
Flexible output data formatting.
Sequencer allows up to 8 sources to be automatically scanned using one of four channel characteristic
profiles without software intervention.
Eight-word conversion data FIFO for DMA operations.
Multiple SARADC modules can work together synchronously or by interleaving samples.
Includes two internal references (1.65 V fast-settling, 1.2/2.4 V precision), support for an external
reference, and support for an external signal ground.
4.7.2. Sample Sync Generator (SSG0)
The SSG module includes a phase counter and a pulse generator. The phase counter is a 4-bit free-running
counter clocked from the SARADC module clock. Counting-up from zero, the phase counter marks sixteen equallyspaced events for any number of SARADC modules. The ADCs can use this phase counter to start a conversion.
The programmable pulse generator creates a 50% duty cycle pulse with a period of 16 phase counter ticks. Up to
four programmable outputs available to external devices can be driven by the pulse generator with programmable
polarity and a defined output setting when the pulse generator is stopped.
The Sample Sync Generator module has the following features:
Connects
multiple modules together to perform synchronized actions.
a clock synchronized to the internal sampling clock used by any number of SARADC modules to
pins for use by external devices.
Includes a phase counter, pulse generator, and up to four programmable outputs.
Outputs
4.7.3. 10-Bit Digital-to-Analog Converter (IDAC0, IDAC1)
The IDAC takes a digital value as an input and outputs a proportional constant current on a pin. The IDAC module
includes the following features:
10-bit
current DAC with support for four timer, up to seven external I/O, on demand, and SSG0 output
update triggers.
Ability to update on rising, falling, or both edges for any of the external I/O trigger sources (DACnTx).
Supports an output update rate greater than 600 k samples per second.
Support for three full-scale output modes: 0.5 mA, 1.0 mA and 2.0 mA.
Four-word FIFO to aid with high-speed waveform generation or DMA interactions.
Individual FIFO overrun, underrun, and went-empty interrupt status sources.
Support for multiple data packing formats, including: single 10-bit sample per word, dual 10-bit samples per
word, or four 8-bit samples per word.
Support for left- and right-justified data.
Preliminary Rev. 0.8
45
SiM3C1xx
4.7.4. 16-Channel Capacitance-to-Digital Converter (CAPSENSE0)
The Capacitance Sensing module measures capacitance on external pins and converts it to a digital value. The
CAPSENSE module has the following features:
Multiple
start-of-conversion sources (CSnTx).
to convert to 12, 13, 14, or 16 bits.
Automatic threshold comparison with programmable polarity (“less than or equal” or “greater than”).
Four operation modes: single conversion, single scan, continuous single conversion, and continuous scan.
Auto-accumulate mode that will take and average multiple samples together from a single start of
conversion signal.
Single bit retry options available to reduce the effect of noise during a conversion.
Supports channel bonding to monitor multiple channels connected together with a single conversion.
Scanning option allows the module to convert a single or series of channels and compare against the
threshold while the AHB clock is stopped and the core is in a low power mode.
Option
4.7.5. Low Current Comparators (CMP0, CMP1)
The Comparators take two analog input voltages and output the relationship between these voltages (less than or
greater than) as a digital signal. The Low Power Comparator module includes the following features:
Multiple
sources for the positive and negative poles, including VDD, VREF, and 8 I/O pins.
Two outputs are available: a digital synchronous latched output and a digital asynchronous raw output.
Programmable hysteresis and response time.
Falling or rising edge interrupt options on the comparator output.
4.7.6. Current-to-Voltage Converter (IVC0)
The IVC module provides inputs to the SARADCn modules so the input current can be measured. The IVC module
has the following features:
Two
independent channels.
Programmable input ranges (1–6 mA full-scale).
46
Preliminary Rev. 0.8
SiM3C1xx
4.8. Reset Sources
Reset circuitry allows the controller to be easily placed in a predefined default condition. On entry to this reset
state, the following occur:
The
core halts program execution.
Module registers are initialized to their defined reset values unless the bits reset only with a power-on
reset.
External port pins are forced to a known state.
Interrupts and timers are disabled.
Clocks to all AHB peripherals are enabled.
Clocks to all APB peripherals other than Watchdog Timer, EMIF0, and DMAXBAR are disabled.
All registers are reset to the predefined values noted in the register descriptions unless the bits only reset with a
power-on reset. The contents of RAM are unaffected during a reset; any previously stored data is preserved as
long as power is not lost.
The Port I/O latches are reset to 1 in open-drain mode. Weak pullups are enabled during and after the reset. For
VDD Supply Monitor and power-on resets, the RESET pin is driven low until the device exits the reset state.
On exit from the reset state, the program counter (PC) is reset, and the system clock defaults to an internal
oscillator. The Watchdog Timer is enabled with the Low Frequency Oscillator (LFO0) as its clock source. Program
execution begins at location 0x00000000.
Reset Sources
RESET
VDD Supply
Monitor
Missing Clock
Detector
Watchdog Timer
Software Reset
system reset
Comparator 0
Comparator 1
RTC0 Alarm
PMU / Wakeup
Core Reset
Preliminary Rev. 0.8
47
SiM3C1xx
4.9. Security
The peripherals on the SiM3C1xx devices have a register lock and key mechanism that prevents any undesired
accesses of the peripherals from firmware. Each bit in the PERIPHLOCKx registers controls a set of peripherals. A
key sequence must be written in order to the KEY register to modify any of the bits in PERIPHLOCKx. Any
subsequent write to KEY will then inhibit any accesses of PERIPHLOCKx until it is unlocked again through KEY.
Reading the KEY register indicates the current status of the PERIPHLOCKx lock state.
If a peripheral’s registers are locked, all writes will be ignored. The registers can always be read, regardless of the
peripheral’s lock state.
Peripheral Lock and Key
USART0/1,
UART0/1
SPI0/1/2
I2C0/1
PERIPHLOCK0
EPCA0, PCA0/1
KEY
PERIPHLOCK1
TIMER0/1
SARADC0/1
SSG0
4.10. On-Chip Debugging
The SiM3C1xx devices include JTAG and Serial Wire programming and debugging interfaces and ETM for
instruction trace. The JTAG interface is supported on SiM3C1x7 and SiM3C1x6 devices, and the ETM interface is
supported on SiM3C1x7 devices. The JTAG and ETM interfaces can be optionally enabled to provide more
visibility while debugging at the cost of using several Port I/O pins. Additionally, if the core is configured for Serial
Wire (SW) mode and not JTAG, then the Serial Wire Viewer (SWV) is available to provide a single pin to send out
TPIU messages on SiM3C1x7 and SiM3C1x6 devices.
Most peripherals have the option to halt or continue functioning when the core halts in debug mode.
48
Preliminary Rev. 0.8
SiM3C1xx
5. Pin Definitions and Packaging Information
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
RESET
NC
NC
NC
VREGIN
VSS
VDD
VIO
PB0.0
PB0.1
PB0.2
PB0.3
PB0.4
PB0.5
PB0.6
PB0.7
PB0.8
PB0.9
PB0.10
PB0.11
5.1. SiM3C1x7 Pin Definitions
PB4.5
PB4.4
PB4.3
1
60
PB0.12
2
59
PB0.13
3
58
PB0.14
VSSHD
VIOHD
PB4.2
PB4.1
PB4.0
4
57
5
56
PB0.15
PB1.0
6
55
PB1.1
7
54
PB1.2/TRST
8
53
PB1.3/TDO/SWV
PB3.11
PB3.10
PB3.9
PB3.8
9
52
PB1.4/TDI
10
51
PB1.5/ETM0
80-Pin TQFP
44
SWDIO/TMS
18
43
PB1.10
19
42
PB1.11
20
41
PB1.12
27
26
25
24
23
22
21
PB2.14
PB2.13
PB2.12
PB2.11
PB2.10
PB2.9
PB2.8
PB2.7
PB2.6
PB2.5
PB2.4
VIO
VSS
PB2.3
PB2.2
PB2.1
PB2.0
PB1.15
PB1.14
PB1.13
40
17
PB3.2
PB3.1
PB3.0
39
SWCLK/TCK
38
45
37
PB1.9/TRACECLK
16
36
PB1.8/ETM3
46
35
47
15
34
14
33
PB1.7/ETM2
32
48
31
13
30
VIO
PB3.7
PB3.6
PB3.5
PB3.4
PB3.3
29
PB1.6/ETM1
49
28
50
12
11
Figure 5.1. SiM3C1x7-GQ Pinout
Preliminary Rev. 0.8
49
A41
A40
A39
PB4.4
A1
D5
PB4.3
A2
B36
B35
B34
B33
B32
B31
B30
B29
B1
A35
PB0.13
PB0.14
B27
A34
PB0.15
A33
PB1.0
A32
PB1.2*
A31
PB1.4*
A30
PB1.6*
A29
VIO
A28
PB1.9*
A27
SWDIO*
A26
PB1.10
D7
A25
PB1.11
D3
PB1.12
B3
PB3.11
PB1.1
B25
B4
PB3.10
PB1.3*
B24
B5
PB3.9
PB1.5*
B23
PB3.7
PB1.7*
B22
B7
PB3.5
PB1.8*
B21
B8
PB3.3
SWCLK*
B20
A5
A6
92 pin LGA
(Top View)
A7
A8
A9
VSS
VSS
PB2.2
PB2.0
A10
B11
B12
B13
B14
B15
B16
B17
A13
A14
A15
A16
PB2.12
PB2.11
PB2.9
B18
A17
A18
A19
A20
A21
A22
A23
A24
PB1.13
D2
B10
PB1.14
D6
PB1.15
A12
PB2.1
PB3.0
B19
PB2.3
A11
PB2.14
PB3.1
PB2.13
B9
VIO
PB3.2
PB0.12
B26
PB2.4
PB3.4
A36
A4
B6
PB3.6
D8
PB2.5
PB3.8
B28
VSSHD
PB2.6
PB4.0
D4
PB2.7
PB4.1
A37
B2
PB2.8
PB4.2
A38
A3
PB2.10
VIOHD
PB0.11
PB0.8
A42
PB0.10
PB0.6
A43
PB0.9
PB0.4
A44
PB0.7
PB0.2
A45
PB0.5
VIO
A46
PB0.3
VDD
A47
PB0.1
VREGIN
A48
PB0.0
NC
D1
VSS
NC
PB4.5
NC
RESET
SiM3C1xx
*Noted pins are listed in the pinout table and 80-pin TQFP package figure with additional names.
These alternate functions are also present on the 92-pin LGA package and are identical to those on the
80-pin TQFP package.
Figure 5.2. SiM3C1x7-GM Pinout
50
Preliminary Rev. 0.8
SiM3C1xx
Port-Mapped Level Shifter
74 A44
VIO
Power (I/O)
32 A19
49 A29
73 A43
VREGIN
Power (Regulator)
76 A45
VSSHD
Ground (High Drive)
4
B2
VIOHD
Power (High Drive)
5
A3
RESET
Active-low Reset
80 A48
SWCLK / TCK
Serial Wire / JTAG
45 B20
SWDIO / TMS
Serial Wire / JTAG
44 A27
PB0.0
Standard I/O
72 B33 XBR0

ADC0.0
PB0.1
Standard I/O
71 B32 XBR0

ADC0.1
CS0.0
PB0.2
Standard I/O
70 A42 XBR0

ADC0.2
CS0.1
PB0.3
Standard I/O
69 B31 XBR0

ADC0.3
CS0.2
PB0.4
Standard I/O
68 A41 XBR0

ADC0.4
CS0.3
PB0.5
Standard I/O
67 B30 XBR0

ADC0.5
CS0.4
PB0.6
Standard I/O
66 A40 XBR0

CS0.5
PB0.7
Standard I/O
65 B29 XBR0

ADC0.6
CS0.6
IVC0.0
Preliminary Rev. 0.8
Functions
Power (Core)
Analog or Additional
VDD
External Trigger Inputs
33 B15
75 B34
Output Toggle Logic
Ground
(m = muxed mode)
Port Match
VSS
Pin Numbers LGA-92
Type
Pin Numbers TQFP-80
Pin Name
Crossbar Capability
(see Port Config Section)
External Memory Interface
Table 5.1. Pin Definitions and alternate functions for SiM3C1x7
51
SiM3C1xx
Port-Mapped Level Shifter
PB0.9
Standard I/O
63 A38 XBR0

ADC0.8
RTC1
PB0.10
Standard I/O
62 A37 XBR0

RTC2
PB0.11
Standard I/O
61
D4 XBR0

ADC0.9
VREFGND
PB0.12
Standard I/O
60 A36 XBR0

ADC0.10
VREF
PB0.13
Standard I/O
59 A35 XBR0

IDAC0
PB0.14
Standard I/O
58 B27 XBR0

IDAC1
PB0.15
Standard I/O
57 A34 XBR0

XTAL1
PB1.0
Standard I/O
56 A33 XBR0

XTAL2
PB1.1
Standard I/O
55 B25 XBR0

ADC0.11
PB1.2/TRST
Standard I/O /JTAG
54 A32 XBR0

PB1.3/TDO/
SWV
Standard I/O /JTAG/
Serial Wire Viewer
53 B24 XBR0

ADC0.12
ADC1.12
PB1.4/TDI
Standard I/O /JTAG
52 A31 XBR0

ADC0.13
ADC1.13
PB1.5/ETM0
Standard I/O /ETM
51 B23 XBR0

ADC0.14
ADC1.14
PB1.6/ETM1
Standard I/O /ETM
50 A30 XBR0

ADC0.15
ADC1.15
PB1.7/ETM2
Standard I/O /ETM
48 B22 XBR0

ADC1.11
CS0.8
PB1.8/ETM3
Standard I/O /ETM
47 B21 XBR0

ADC1.10
CS0.9
52
Preliminary Rev. 0.8
Functions
ADC0.7
CS0.7
IVC0.1
Analog or Additional

External Trigger Inputs
64 A39 XBR0
Output Toggle Logic
Standard I/O
(m = muxed mode)
Port Match
PB0.8
Pin Numbers LGA-92
Type
Pin Numbers TQFP-80
Pin Name
Crossbar Capability
(see Port Config Section)
External Memory Interface
Table 5.1. Pin Definitions and alternate functions for SiM3C1x7 (Continued)
SiM3C1xx
Port-Mapped Level Shifter
Standard I/O
43 A26 XBR0

A23m/
A15
DMA0T1
ADC1.8
PB1.11
Standard I/O
42 A25 XBR0

A22m/
A14
DMA0T0
ADC1.7
PB1.12
Standard I/O
41
D3 XBR0

A21m/
A13
PB1.13
Standard I/O
40 A24 XBR0

A20m/
A12
ADC0T15
WAKE.0
ADC1.5
CS0.10
PB1.14
Standard I/O
39 A23 XBR0

A19m/
A11
ADC1T15
WAKE.1
ADC1.4
CS0.11
PB1.15
Standard I/O
38 A22 XBR0

A18m/
A10
WAKE.2
ADC1.3
CS0.12
PB2.0
Standard I/O
37 B17 XBR1

A17m/
A9
LSI0 Yes
INT0.0
INT1.0
WAKE.3
ADC1.2
CS0.13
PB2.1
Standard I/O
36 A21 XBR1

A16m/
A8
LSI1 Yes
INT0.1
INT1.1
WAKE.4
ADC1.1
CS0.14
PB2.2
Standard I/O
35 B16 XBR1

AD15m/
A7
LSI2 Yes
INT0.2
INT1.2
WAKE.5
ADC1.0
CS0.15
PMU_Asleep
PB2.3
Standard I/O
34 A20 XBR1

AD14m/
A6
LSI3 Yes
INT0.3
INT1.3
WAKE.6
PB2.4
Standard I/O
31 B14 XBR1

AD13m/
A5
LSI4 Yes
INT0.4
INT1.4
WAKE.7
PB2.5
Standard I/O
30 A18 XBR1

AD12m / LSI5 Yes
A4
Functions
PB1.10
Analog or Additional

External Trigger Inputs
46 A28 XBR0
Output Toggle Logic
Standard I/O /ETM
(m = muxed mode)
Port Match
PB1.9/
TRACECLK
Pin Numbers LGA-92
Type
Pin Numbers TQFP-80
Pin Name
Crossbar Capability
(see Port Config Section)
External Memory Interface
Table 5.1. Pin Definitions and alternate functions for SiM3C1x7 (Continued)
ADC1.9
Preliminary Rev. 0.8
ADC1.6
INT0.5
INT1.5
53
SiM3C1xx
Port-Mapped Level Shifter
Yes
INT0.6
INT1.6
PB2.7
Standard I/O
28 A17 XBR1

AD10m/
A2
Yes
INT0.7
INT1.7
PB2.8
Standard I/O
27 B12 XBR1

AD9m/
A1
Yes
PB2.9
Standard I/O
26 A16 XBR1

AD8m/
A0
Yes
PB2.10
Standard I/O
25
B11 XBR1

AD7m/
D7
Yes
PB2.11
Standard I/O
24 A15 XBR1

AD6m/
D6
Yes
CMP0P.0
CMP1P.0
PB2.12
Standard I/O
23 A14 XBR1

AD5m/
D5
Yes
CMP0N.0
CMP1N.0
RTC0OSC_OUT
PB2.13
Standard I/O
22 A13 XBR1

AD4m/
D4
Yes
CMP0P.1
CMP1P.1
PB2.14
Standard I/O
21
D2 XBR1

AD3m/
D3
Yes
CMP0N.1
CMP1N.1
PB3.0
5 V Tolerant I/O
20 A12 XBR1

AD2m/
D2
CMP0P.2
CMP1P.2
PB3.1
5 V Tolerant I/O
19
A11 XBR1

AD1m/
D1
CMP0N.2
CMP1N.2
PB3.2
5 V Tolerant I/O
18 A10 XBR1

AD0m/
D0
DAC0T0
DAC1T0
LPT0T0
CMP0P.3
CMP1P.3
PB3.3
5 V Tolerant I/O
17

WR
DAC0T1
DAC1T1
INT0.8
INT1.8
CMP0N.3
CMP1N.3
54
B8 XBR1
Preliminary Rev. 0.8
Functions
AD11m/
A3
Analog or Additional

External Trigger Inputs
29 B13 XBR1
Output Toggle Logic
Standard I/O
(m = muxed mode)
Port Match
PB2.6
Pin Numbers LGA-92
Type
Pin Numbers TQFP-80
Pin Name
Crossbar Capability
(see Port Config Section)
External Memory Interface
Table 5.1. Pin Definitions and alternate functions for SiM3C1x7 (Continued)
SiM3C1xx
A9 XBR1

OE
INT0.9
INT1.9
WAKE.8
CMP0P.4
CMP1P.4
PB3.5
5 V Tolerant I/O
15
B7 XBR1

ALEm
DAC0T2
DAC1T2
INT0.10
INT1.10
WAKE.9
CMP0N.4
CMP1N.4
PB3.6
5 V Tolerant I/O
14
A8 XBR1

CS0
DAC0T3
DAC1T3
INT0.11
INT1.11
WAKE.10
CMP0P.5
CMP1P.5
PB3.7
5 V Tolerant I/O
13
B6 XBR1

BE1
DAC0T4
DAC1T4
LPT0T1
INT0.12
INT1.12
WAKE.11
CMP0N.5
CMP1N.5
PB3.8
5 V Tolerant I/O
12
A7 XBR1

CS1
DAC0T5
DAC1T5
LPT0T2
INT0.13
INT1.13
WAKE.12
CMP0P.6
CMP1P.6
EXREGSP
PB3.9
5 V Tolerant I/O
11
B5 XBR1

BE0
DAC0T6
DAC1T6
INT0.14
INT1.14
WAKE.13
CMP0N.6
CMP1N.6
EXREGSN
PB3.10
5 V Tolerant I/O
10
B4 XBR1

INT0.15
INT1.15
WAKE.14
CMP0P.7
CMP1P.7
EXREGOUT
PB3.11
5 V Tolerant I/O
9
B3 XBR1

WAKE.15
CMP0N.7
CMP1N.7
EXREGBD
Preliminary Rev. 0.8
Functions
16
Analog or Additional
Port Match
5 V Tolerant I/O
External Trigger Inputs
Crossbar Capability
(see Port Config Section)
PB3.4
Output Toggle Logic
Pin Numbers LGA-92
Port-Mapped Level Shifter
Type
(m = muxed mode)
Pin Name
Pin Numbers TQFP-80
External Memory Interface
Table 5.1. Pin Definitions and alternate functions for SiM3C1x7 (Continued)
55
SiM3C1xx
LSO0
PB4.1
High Drive I/O
7
A5
LSO1
PB4.2
High Drive I/O
6
A4
LSO2
PB4.3
High Drive I/O
3
A2
LSO3
PB4.4
High Drive I/O
2
A1
LSO4
PB4.5
High Drive I/O
1
D1
LSO5
Functions
A6
Analog or Additional
8
External Trigger Inputs
High Drive I/O
Output Toggle Logic
Port-Mapped Level Shifter
PB4.0
(m = muxed mode)
Pin Numbers LGA-92
External Memory Interface
Type
Port Match
Pin Name
Pin Numbers TQFP-80
Crossbar Capability
(see Port Config Section)
Table 5.1. Pin Definitions and alternate functions for SiM3C1x7 (Continued)
Note: All unnamed pins on the LGA-92 package are no-connect pins. They should be soldered to the PCB for mechanical stability, but have no internal connections to the device.
56
Preliminary Rev. 0.8
SiM3C1xx
RESET
NC
NC
NC
VREGIN
VSS
VDD
PB0.0
PB0.1
PB0.2
PB0.3
PB0.4
PB0.5
PB0.6
PB0.7
PB0.8
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
5.2. SiM3C1x6 Pin Definitions
PB4.3
1
48
PB0.9
VSSHD
VIOHD
PB4.2
2
47
3
46
4
45
PB0.10
PB0.11
PB0.12
PB4.1
PB4.0
PB3.9
PB3.8
5
44
6
43
7
42
PB3.7
PB3.6
PB3.5
PB3.4
9
41
64 Pin TQFP
40
24
25
26
27
28
29
30
31
32
VIO
VSS
PB1.12
PB1.11
PB1.10
PB1.9
PB1.8
PB1.7
PB1.6
PB1.13
33
23
16
22
34
PB1.14
15
21
35
PB1.15
14
20
36
PB2.0
37
13
19
12
PB2.1
38
18
11
PB2.2
39
17
10
PB2.3
PB3.3
PB3.2
PB3.1
PB3.0
8
PB0.13
PB0.14/TDO/SWV
PB0.15/TDI
PB1.0
PB1.1
VIO
PB1.2
PB1.3
SWCLK/TCK
SWDIO/TMS
PB1.4
PB1.5
Figure 5.3. SiM3C1x6-GQ Pinout
Preliminary Rev. 0.8
57
RESET
NC
NC
NC
VREGIN
VSS
VDD
PB0.0
PB0.1
PB0.2
PB0.3
PB0.4
PB0.5
PB0.6
PB0.7
PB0.8
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
SiM3C1xx
PB4.3
1
48
PB0.9
VSSHD
2
47
PB0.10
VIOHD
3
46
PB0.11
PB4.2
4
45
PB0.12
PB4.1
5
44
PB0.13
PB4.0
6
43
PB0.14/TDO/SWV
PB3.9
7
42
PB0.15/TDI
PB3.8
8
64 pin QFN
41
PB1.0
PB3.7
9
(TopView)
40
PB1.1
PB3.6
10
39
VIO
PB3.5
11
38
PB1.2
PB3.4
12
37
PB1.3
PB3.3
13
36
SWCLK/TCK
PB3.2
14
35
SWDIO/TMS
PB3.1
15
34
PB1.4
PB3.0
16
33
PB1.5
24
25
26
27
28
29
30
31
32
VIO
VSS
PB1.12
PB1.11
PB1.10
PB1.9
PB1.8
PB1.7
PB1.6
21
PB1.15
23
20
PB2.0
PB1.13
19
PB2.1
22
18
PB2.2
PB1.14
17
PB2.3
VSS
Figure 5.4. SiM3C1x6-GM Pinout
58
Preliminary Rev. 0.8
SiM3C1xx
Port-Mapped Level Shifter
Power (Core)
58
VIO
Power (I/O)
24
39
VREGIN
Power (Regulator)
60
VSSHD
Ground (High Drive)
2
VIOHD
Power (High Drive)
3
RESET
Active-low Reset
64
SWCLK/TCK
Serial Wire / JTAG
36
SWDIO/TMS
Serial Wire / JTAG
35
PB0.0
Standard I/O
57
XBR0

ADC0.2
CS0.1
PB0.1
Standard I/O
56
XBR0

ADC0.3
CS0.2
PB0.2
Standard I/O
55
XBR0

ADC0.4
CS0.3
PB0.3
Standard I/O
54
XBR0

ADC0.5
CS0.4
PB0.4
Standard I/O
53
XBR0

ADC0.6
CS0.5
IVC0.0
PB0.5
Standard I/O
52
XBR0

ADC0.7
CS0.6
IVC0.1
PB0.6
Standard I/O
51
XBR0

ADC0.8
CS0.7
RTC1
Preliminary Rev. 0.8
Functions
VDD
Analog or Additional
25
59
External Trigger Inputs
Ground
Output Toggle Logic
Port Match
VSS
(m = muxed mode)
Type
Pin Numbers
Pin Name
Crossbar Capability
(see Port Config Section)
External Memory Interface
Table 5.2. Pin Definitions and alternate functions for SiM3C1x6
59
SiM3C1xx
Port-Mapped Level Shifter

RTC2
PB0.8
Standard I/O
49
XBR0

ADC0.9
VREFGND
PB0.9
Standard I/O
48
XBR0

ADC0.10
VREF
PB0.10
Standard I/O
47
XBR0

ADC1.6
IDAC0
PB0.11
Standard I/O
46
XBR0

IDAC1
PB0.12
Standard I/O
45
XBR0

XTAL1
PB0.13
Standard I/O
44
XBR0

XTAL2
43
XBR0

ADC0.12
ADC1.12
PB0.14/TDO/ Standard I/O / JTAG
SWV
/ Serial Wire Viewer
Functions
XBR0
Analog or Additional
50
External Trigger Inputs
Standard I/O
Output Toggle Logic
Port Match
PB0.7
(m = muxed mode)
Type
Pin Numbers
Pin Name
Crossbar Capability
(see Port Config Section)
External Memory Interface
Table 5.2. Pin Definitions and alternate functions for SiM3C1x6 (Continued)
PB0.15/TDI
Standard I/O / JTAG
42
XBR0

ADC0.13
ADC1.13
PB1.0
Standard I/O
41
XBR0

ADC0.14
ADC1.14
PB1.1
Standard I/O
40
XBR0

ADC0.15
ADC1.15
PB1.2
Standard I/O
38
XBR0

ADC1.11
CS0.8
PB1.3
Standard I/O
37
XBR0

ADC1.10
CS0.9
PB1.4
Standard I/O
34
XBR0

ADC1.8
PB1.5
Standard I/O
33
XBR0

ADC1.7
PB1.6
Standard I/O
32
XBR0

PB1.7
Standard I/O
31
XBR0

60
AD15m/
A7
Preliminary Rev. 0.8
ADC0T15
WAKE.0
ADC1.5
CS0.10
ADC1T15
WAKE.1
ADC1.4
CS0.11
SiM3C1xx
Port-Mapped Level Shifter

AD14m/
A6
WAKE.2
ADC1.3
CS0.12
PB1.9
Standard I/O
29
XBR0

AD13m/
A5
WAKE.3
ADC1.2
CS0.13
PB1.10
Standard I/O
28
XBR0

AD12m/
A4
DMA0T1
WAKE.4
ADC1.1
CS0.14
PB1.11
Standard I/O
27
XBR0

AD11m/
A3
DMA0T0
WAKE.5
ADC1.0
CS0.15
PMU_Asleep
PB1.12
Standard I/O
26
XBR0

AD10m/
A2
WAKE.6
PB1.13
Standard I/O
23
XBR0

AD9m/
A1
PB1.14
Standard I/O
22
XBR0

AD8m/
A0
PB1.15
Standard I/O
21
XBR0

AD7m/
D7
PB2.0
Standard I/O
20
XBR1

AD6m/
D6
LSI0 Yes
INT0.0
INT1.0
PB2.1
Standard I/O
19
XBR1

AD5m/
D5
LSI1 Yes
INT0.1
INT1.1
PB2.2
Standard I/O
18
XBR1

AD4m/
D4
LSI2 Yes
INT0.2
INT1.2
CMP0N.0
CMP1N.0
RTC0OSC_OUT
PB2.3
Standard I/O
17
XBR1

AD3m/
D3
LSI3 Yes
INT0.3
INT1.3
CMP0P.0
CMP1P.0
PB3.0
5 V Tolerant I/O
16
XBR1

AD2m/
D2
CMP0P.1
CMP1P.1
PB3.1
5 V Tolerant I/O
15
XBR1

AD1m/
D1
CMP0N.1
CMP1N.1
Preliminary Rev. 0.8
Functions
XBR0
Analog or Additional
30
External Trigger Inputs
Standard I/O
Output Toggle Logic
Port Match
PB1.8
(m = muxed mode)
Type
Pin Numbers
Pin Name
Crossbar Capability
(see Port Config Section)
External Memory Interface
Table 5.2. Pin Definitions and alternate functions for SiM3C1x6 (Continued)
61
SiM3C1xx
62
Port-Mapped Level Shifter

AD0m/
D0
DAC0T0
DAC1T0
LPT0T0
WAKE.8
CMP0P.2
CMP1P.2
PB3.3
5 V Tolerant I/O
13
XBR1

WR
DAC0T1
DAC1T1
INT0.4
INT1.4
WAKE.9
CMP0N.2
CMP1N.2
PB3.4
5 V Tolerant I/O
12
XBR1

OE
INT0.5
INT1.5
WAKE.10
CMP0P.3
CMP1P.3
PB3.5
5 V Tolerant I/O
11
XBR1

ALEm
DAC0T2
DAC1T2
INT0.6
INT1.6
WAKE.11
CMP0N.3
CMP1N.3
PB3.6
5 V Tolerant I/O
10
XBR1

CS0
DAC0T3
DAC1T3
INT0.7
INT1.7
WAKE.12
CMP0P.4
CMP1P.4
EXREGSP
PB3.7
5 V Tolerant I/O
9
XBR1

BE1
DAC0T4
DAC1T4
INT0.8
INT1.8
WAKE.13
CMP0N.4
CMP1N.4
EXREGSN
PB3.8
5 V Tolerant I/O
8
XBR1

CS1
DAC0T5
DAC1T5
LPT0T1
INT0.9
INT1.9
WAKE.14
CMP0P.5
CMP1P.5
EXREGOUT
Preliminary Rev. 0.8
Functions
XBR1
Analog or Additional
14
External Trigger Inputs
5 V Tolerant I/O
Output Toggle Logic
Port Match
PB3.2
(m = muxed mode)
Type
Pin Numbers
Pin Name
Crossbar Capability
(see Port Config Section)
External Memory Interface
Table 5.2. Pin Definitions and alternate functions for SiM3C1x6 (Continued)
SiM3C1xx
5 V Tolerant I/O
7
PB4.0
High Drive I/O
6
LSO0
PB4.1
High Drive I/O
5
LSO1
PB4.2
High Drive I/O
4
LSO2
PB4.3
High Drive I/O
1
LSO3
BE0
Preliminary Rev. 0.8
DAC0T6
DAC1T6
LPT0T2
INT0.10
INT1.10
WAKE.15
Functions
PB3.9
Analog or Additional
Type
External Trigger Inputs
Pin Name
Output Toggle Logic
Port-Mapped Level Shifter

(m = muxed mode)
Port Match
XBR1
External Memory Interface
Crossbar Capability
(see Port Config Section)
Pin Numbers
Table 5.2. Pin Definitions and alternate functions for SiM3C1x6 (Continued)
CMP0N.5
CMP1N.5
EXREGBD
63
SiM3C1xx
RESET
NC
NC
NC
VREGIN
VDD
PB0.0
PB0.1
PB0.2
PB0.3
40
39
38
37
36
35
34
33
32
31
5.3. SiM3C1x4 Pin Definitions
PB4.3
1
30
PB0.4
VSSHD
2
29
PB0.5
VIOHD
3
28
PB0.6
PB4.2
4
27
PB0.7
PB4.1
5
40 pin QFN
26
PB0.8
PB4.0
6
(Top View)
25
PB0.9
PB3.3
7
24
SWCLK
PB3.2
8
23
SWDIO
PB3.1
9
22
PB0.10
PB3.0
10
21
PB0.11
13
14
15
16
17
18
19
20
VSS
PB1.1
PB1.0
PB0.15
PB0.14
PB0.13
PB0.12
12
PB1.2
VIO
11
PB1.3
VSS
Figure 5.5. SiM3C1x4-GM Pinout
64
Preliminary Rev. 0.8
SiM3C1xx
VDD
Power (Core)
35
VIO
Power (I/O)
13
VREGIN
Power (Regulator)
36
VSSHD
Ground (High Drive)
2
VIOHD
Power (High Drive)
3
RESET
Active-low Reset
40
SWCLK
Serial Wire
24
SWDIO
Serial Wire
23
PB0.0
Standard I/O
34
XBR0

ADC0.8
CS0.7
RTC1
PB0.1
Standard I/O
33
XBR0

RTC2
PB0.2
Standard I/O
32
XBR0

ADC0.9
CS0.0
VREFGND
PB0.3
Standard I/O
31
XBR0

ADC0.10
CS0.1
VREF
PB0.4
Standard I/O
30
XBR0

ADC1.6
CS0.2
IDAC0
PB0.5
Standard I/O
29
PB0.6
Standard I/O
28
XBR0

ADC0.0
CS0.3
XTAL1
PB0.7
Standard I/O
27
XBR0

ADC0.1
CS0.4
XTAL2
Functions
14
Analog or Additional
Ground
External Trigger Inputs
Port Match
VSS
Output Toggle Logic
Type
Pin Numbers
Pin Name
Crossbar Capability
(see Port Config Section)
Table 5.3. Pin Definitions and alternate functions for SiM3C1x4
IDAC1
Preliminary Rev. 0.8
65
SiM3C1xx
66
XBR0

ADC0.14
ADC1.14
PB0.9
Standard I/O
25
XBR0

ADC0.15
ADC1.15
PB0.10
Standard I/O
22
XBR0

DMA0T1
ADC1.8
PB0.11
Standard I/O
21
XBR0

DMA0T0
ADC1.7
PB0.12
Standard I/O
20
XBR0

ADC0T15
WAKE.0
ADC1.5
CS0.10
PB0.13
Standard I/O
19
XBR0

ADC1T15
WAKE.1
ADC1.4
CS0.11
PB0.14
Standard I/O
18
XBR0

WAKE.2
ADC1.3
CS0.12
PB0.15
Standard I/O
17
XBR0

WAKE.3
ADC1.2
CS0.13
PB1.0
Standard I/O
16
XBR0

WAKE.4
ADC1.1
CS0.14
PB1.1
Standard I/O
15
XBR0

WAKE.5
ADC1.0
CS0.15
PMU_Asleep
PB1.2
Standard I/O
12
XBR0

CMP0N.0
CMP1N.0
RTC0OSC_OUT
PB1.3
Standard I/O
11
XBR0

CMP0P.0
CMP1P.0
PB3.0
5 V Tolerant I/O
10
XBR1

Preliminary Rev. 0.8
DAC0T0
DAC1T0
LPT0T0
INT0.0
INT1.0
WAKE.12
Functions
26
Analog or Additional
Standard I/O
External Trigger Inputs
Port Match
PB0.8
Output Toggle Logic
Type
Pin Numbers
Pin Name
Crossbar Capability
(see Port Config Section)
Table 5.3. Pin Definitions and alternate functions for SiM3C1x4 (Continued)
CMP0P.1
CMP1P.1
EXREGSP
SiM3C1xx
XBR1

DAC0T1
DAC1T1
LPT0T1
INT0.1
INT1.1
WAKE.13
CMP0N.1
CMP1N.1
EXREGSN
PB3.2
5 V Tolerant I/O
8
XBR1

DAC0T2
DAC1T2
LPT0T2
INT0.2
INT1.3
WAKE.14
CMP0P.2
CMP1P.2
EXREGOUT
PB3.3
5 V Tolerant I/O
7
XBR1

DAC0T3
DAC1T3
INT0.3
INT1.3
WAKE.15
CMP0N.2
CMP1N.2
EXREGBD
PB4.0
High Drive I/O
6
PB4.1
High Drive I/O
5
PB4.2
High Drive I/O
4
PB4.3
High Drive I/O
1
Preliminary Rev. 0.8
Functions
9
Analog or Additional
5 V Tolerant I/O
External Trigger Inputs
Port Match
PB3.1
Output Toggle Logic
Type
Pin Numbers
Pin Name
Crossbar Capability
(see Port Config Section)
Table 5.3. Pin Definitions and alternate functions for SiM3C1x4 (Continued)
67
SiM3C1xx
6. Ordering Information
Si M3 C 1 4 4 – B – GM
Temperature Grade and Package Type
Revision
Pin Count – 4 (40 pin), 6 (64 pin), 7 (80 or 92 pin)
Memory Size – 3 (32 kB), 4 (64 kB), 5 (128 kB), 6 (256 kB)
Feature Set – varies by family
Family – U (USB), C (Core)
Core – M3 (Cortex M3)
Silicon Labs
Figure 6.1. SiM3C1xx Part Numbering
All devices in the SiM3C1xx family have the following features:
Core: ARM Cortex-M3 with maximum operating frequency of 80 MHz.
Flash Program Memory: 32-256 kB, in-system programmable.
RAM: 8–32 kB SRAM, with 4 kB retention SRAM
I/O: Up to 65 multifunction I/O pins, including high-drive and 5 V-tolerant pins.
Clock Sources: Internal and external oscillator options.
16-Channel DMA Controller.
128/192/256-bit AES.
16/32-bit CRC.
Timers: 2 x 32-bit (4 x 16-bit).
Real-Time Clock.
Low-Power Timer.
PCA: 1 x 6 channels (Enhanced), 2 x 2 channels (Standard). PWM, capture, and clock generation
capabilites.
ADC: 2 x 12-bit 250 ksps (10-bit 1 Msps) SAR.
DAC: 2 x 10-bit IDAC.
Temperature Sensor.
Internal VREF.
16-channel Capacitive Sensing (CAPSENSE).
Comparator: 2 x low current.
Current to Voltage Converter (IVC).
Buses: 2 x USART, 2 x UART, 3 x SPI, 2 x I2C, 1 x I2S.
The inclusion of some features varies across different members of the device family. The differences are detailed in
Table 6.1.
Serial
68
Preliminary Rev. 0.8
SiM3C1xx
External Memory Interface (EMIF)
Maximum Number of EMIF Address/Data Pins
Digital Port I/Os (Total)
Digital Port I/Os with High Drive Capability
Number of SARADC0 Channels
Number of SARADC1 Channels
Number of CAPSENSE0 Channels
Number of Comparator 0/1 Inputs (+/-)
Number of PMU Pin Wake Sources
JTAG Debugging Interface
ETM Debugging Interface
Serial Wire Debugging Interface
Lead-free (RoHS Compliant)
Package

24
65
6
16
16
16
8/8
16




LGA-92
SiM3C167-B-GQ 256 32

24
65
6
16
16
16
8/8
16




TQFP-80
SiM3C166-B-GM 256 32

16
50
4
13
15
15
6/6
15



QFN-64
SiM3C166-B-GQ 256 32

16
50
4
13
15
15
6/6
15



TQFP-64
28
4
7
11
12
3/3
10


QFN-40
Flash Memory (kB)
SiM3C167-B-GM 256 32
Ordering Part Number
RAM (kB)
Table 6.1. Product Selection Guide
SiM3C164-B-GM 256 32
SiM3C157-B-GM 128 32

24
65
6
16
16
16
8/8
16




LGA-92
SiM3C157-B-GQ 128 32

24
65
6
16
16
16
8/8
16




TQFP-80
SiM3C156-B-GM 128 32

16
50
4
13
15
15
6/6
15



QFN-64
SiM3C156-B-GQ 128 32

16
50
4
13
15
15
6/6
15



TQFP-64
28
4
7
11
12
3/3
10


QFN-40
SiM3C154-B-GM 128 32
SiM3C146-B-GM 64
16

16
50
4
13
15
15
6/6
15



QFN-64
SiM3C146-B-GQ
64
16

16
50
4
13
15
15
6/6
15



TQFP-64
SiM3C144-B-GM 64
16
28
4
7
11
12
3/3
10


QFN-40
SiM3C136-B-GM 32
8

16
50
4
13
15
15
6/6
15



QFN-64
SiM3C136-B-GQ
32
8

16
50
4
13
15
15
6/6
15



TQFP-64
SiM3C134-B-GM 32
8
28
4
7
11
12
3/3
10


QFN-40
Preliminary Rev. 0.8
69
SiM3C1xx
6.1. LGA-92 Package Specifications
Figure 6.2. LGA-92 Package Drawing
Table 6.2. LGA-92 Package Dimensions
Dimension
A
b
c
D
D1
D2
e
E
E1
E2
aaa
bbb
ccc
ddd
eee
Min
0.74
0.25
3.15
—
—
—
—
—
Nominal
0.84
0.30
3.20
7.00 BSC
6.50 BSC
4.00 BSC
0.50 BSC
7.00 BSC
6.50 BSC
4.00 BSC
—
—
—
—
—
Max
0.94
0.35
3.25
0.10
0.10
0.08
0.10
0.10
Notes:
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. Recommended card reflow profile is per the JEDEC/IPC J-STD-020
specification for Small Body Components.
70
Preliminary Rev. 0.8
SiM3C1xx
Figure 6.3. LGA-92 Landing Diagram
Table 6.3. LGA-92 Landing Diagram Dimensions
Dimension
Typical
Max
C1
6.50
—
C2
6.50
—
e
0.50
—
f
—
0.35
P1
—
3.20
P2
—
3.20
Notes:
1. All dimensions shown are in millimeters (mm) unless otherwise
noted.
2. All feature sizes shown are at Maximum Material Condition (MMC)
and a card fabrication tolerance of 0.05 mm is assumed.
3. Dimensioning and Tolerancing is per the ANSI Y14.5M-1994
specification.
4. This land pattern design is based on the IPC-7351 guidelines.
Preliminary Rev. 0.8
71
SiM3C1xx
6.1.1. LGA-92 Solder Mask Design
All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad
is to be 60 µm minimum, all the way around the pad.
6.1.2. LGA-92 Stencil Design
1. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure
good solder paste release.
2. The stencil thickness should be 0.125 mm (5 mils).
3. The ratio of stencil aperture to land pad size should be 1:1 for all perimeter pins.
4. A 2 x 2 array of 1.25 mm square openings on 1.60 mm pitch should be used for the center ground pad.
6.1.3. LGA-92 Card Assembly
1. A No-Clean, Type-3 solder paste is recommended.
2. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body
Components.
72
Preliminary Rev. 0.8
SiM3C1xx
6.2. TQFP-80 Package Specifications
Figure 6.4. TQFP-80 Package Drawing
Table 6.4. TQFP-80 Package Dimensions
Dimension
Min
Nominal
Max
A
—
—
1.20
A1
0.05
—
0.15
A2
0.95
1.00
1.05
b
0.17
0.20
0.27
c
0.09
—
0.20
D
14.00 BSC
D1
12.00 BSC
e
0.50 BSC
E
14.00 BSC
E1
12.00 BSC
Preliminary Rev. 0.8
73
SiM3C1xx
Table 6.4. TQFP-80 Package Dimensions (Continued)
Dimension
Min
Nominal
Max
L
0.45
0.60
0.75
1.00 Ref
L1

0°
3.5°
aaa
0.20
bbb
0.20
ccc
0.08
ddd
0.08
eee
0.05
7°
Notes:
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. This package outline conforms to JEDEC MS-026, variant ADD.
4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020C
specification for Small Body Components.
74
Preliminary Rev. 0.8
SiM3C1xx
Figure 6.5. TQFP-80 Landing Diagram
Table 6.5. TQFP-80 Landing Diagram Dimensions
Dimension
Min
Max
C1
13.30
13.40
C2
13.30
13.40
0.50 BSC
E
X
0.20
0.30
Y
1.40
1.50
Notes:
1. All dimensions shown are in millimeters (mm) unless otherwise
noted.
2. This land pattern design is based on the IPC-7351 guidelines.
Preliminary Rev. 0.8
75
SiM3C1xx
6.2.1. TQFP-80 Solder Mask Design
All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad
is to be 60 µm minimum, all the way around the pad.
6.2.2. TQFP-80 Stencil Design
1. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure
good solder paste release.
2. The stencil thickness should be 0.125 mm (5 mils).
3. The ratio of stencil aperture to land pad size should be 1:1 for all pads.
6.2.3. TQFP-80 Card Assembly
1. A No-Clean, Type-3 solder paste is recommended.
2. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body
Components.
76
Preliminary Rev. 0.8
SiM3C1xx
6.3. QFN-64 Package Specifications
Figure 6.6. QFN-64 Package Drawing
Table 6.6. QFN-64 Package Dimensions
Dimension
Min
Nominal
Max
A
0.80
0.85
0.90
A1
0.00
0.02
0.05
b
0.18
0.25
0.30
9.00 BSC
D
D2
3.95
4.10
e
0.50 BSC
E
9.00 BSC
4.25
E2
3.95
4.10
4.25
L
0.30
0.40
0.50
aaa
0.10
bbb
0.10
ccc
0.08
ddd
0.10
eee
0.05
Notes:
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. This package outline conforms to JEDEC MO-220.
4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020
specification for Small Body Components.
Preliminary Rev. 0.8
77
SiM3C1xx
Figure 6.7. QFN-64 Landing Diagram
Table 6.7. QFN-64 Landing Diagram Dimensions
Dimension
mm
C1
8.90
C2
8.90
E
0.50
X1
0.30
Y1
0.85
X2
4.25
Y2
4.25
Notes:
1. All dimensions shown are in millimeters (mm).
2. This Land Pattern Design is based on the IPC-7351 guidelines.
3. All dimensions shown are at Maximum Material Condition (MMC).
Least Material Condition (LMC) is calculated based on a
Fabrication Allowance of 0.05 mm.
78
Preliminary Rev. 0.8
SiM3C1xx
6.3.1. QFN-64 Solder Mask Design
All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad
is to be 60 µm minimum, all the way around the pad.
6.3.2. QFN-64 Stencil Design
1. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure
good solder paste release.
2. The stencil thickness should be 0.125 mm (5 mils).
3. The ratio of stencil aperture to land pad size should be 1:1 for all pads.
4. A 3x3 array of 1.0 mm square openings on a 1.5 mm pitch should be used for the center ground pad.
6.3.3. QFN-64 Card Assembly
1. A No-Clean, Type-3 solder paste is recommended.
2. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body
Components.
Preliminary Rev. 0.8
79
SiM3C1xx
6.4. TQFP-64 Package Specifications
Figure 6.8. TQFP-64 Package Drawing
Table 6.8. TQFP-64 Package Dimensions
80
Dimension
Min
Nominal
Max
A
—
—
1.20
A1
0.05
—
0.15
A2
0.95
1.00
1.05
b
0.17
0.22
0.27
c
0.09
—
0.20
D
12.00 BSC
D1
10.00 BSC
e
0.50 BSC
E
12.00 BSC
E1
10.00 BSC
L
0.45
0.60
0.75

0°
3.5°
7°
Preliminary Rev. 0.8
SiM3C1xx
Table 6.8. TQFP-64 Package Dimensions (Continued)
Dimension
Min
Nominal
Max
aaa
—
—
0.20
bbb
—
—
0.20
ccc
—
—
0.08
ddd
—
—
0.08
Notes:
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. This package outline conforms to JEDEC MS-026, variant ACD.
4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020
specification for Small Body Components.
Preliminary Rev. 0.8
81
SiM3C1xx
Figure 6.9. TQFP-64 Landing Diagram
Table 6.9. TQFP-64 Landing Diagram Dimensions
Dimension
Min
Max
C1
11.30
11.40
C2
11.30
11.40
0.50 BSC
E
X
0.20
0.30
Y
1.40
1.50
Notes:
1. All dimensions shown are in millimeters (mm) unless otherwise
noted.
2. This land pattern design is based on the IPC-7351 guidelines.
82
Preliminary Rev. 0.8
SiM3C1xx
6.4.1. TQFP-64 Solder Mask Design
All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad
is to be 60 µm minimum, all the way around the pad.
6.4.2. TQFP-64 Stencil Design
1. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure
good solder paste release.
2. The stencil thickness should be 0.125 mm (5 mils).
3. The ratio of stencil aperture to land pad size should be 1:1 for all pads.
6.4.3. TQFP-64 Card Assembly
1. A No-Clean, Type-3 solder paste is recommended.
2. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body
Components.
Preliminary Rev. 0.8
83
SiM3C1xx
6.5. QFN-40 Package Specifications
Figure 6.10. QFN-40 Package Drawing
Table 6.10. QFN-40 Package Dimensions
Dimension
Min
Nominal
Max
A
0.80
0.85
0.90
A1
0.00
0.02
0.05
b
0.18
0.25
0.30
6.00 BSC
D
D2
4.35
4.50
e
0.50 BSC
E
6.00 BSC
4.65
E2
4.35
4.5
4.65
L
0.30
0.40
0.50
aaa
0.10
bbb
0.10
ccc
0.08
ddd
0.10
eee
0.05
Notes:
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. This package outline conforms to JEDEC MO-220.
4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020
specification for Small Body Components.
84
Preliminary Rev. 0.8
SiM3C1xx
Figure 6.11. QFN-40 Landing Diagram
Table 6.11. QFN-40 Landing Diagram Dimensions
Dimension
mm
C1
5.90
C2
5.90
E
0.50
X1
0.30
Y1
0.85
X2
4.65
Y2
4.65
Notes:
1. All dimensions shown are in millimeters (mm).
2. This Land Pattern Design is based on the IPC-7351 guidelines.
3. All dimensions shown are at Maximum Material Condition (MMC).
Least Material Condition (LMC) is calculated based on a
Fabrication Allowance of 0.05 mm.
Preliminary Rev. 0.8
85
SiM3C1xx
6.5.1. QFN-40 Solder Mask Design
All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad
is to be 60 µm minimum, all the way around the pad.
6.5.2. QFN-40 Stencil Design
1. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure
good solder paste release.
2. The stencil thickness should be 0.125 mm (5 mils).
3. The ratio of stencil aperture to land pad size should be 1:1 for all pads.
4. A 3x3 array of 1.1 mm square openings on a 1.6 mm pitch should be used for the center ground pad.
6.5.3. QFN-40 Card Assembly
1. A No-Clean, Type-3 solder paste is recommended.
2. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body
Components.
86
Preliminary Rev. 0.8
SiM3C1xx
7. Revision Specific Behavior
This chapter details any known differences from behavior as stated in the device datasheet and reference manual.
All known errata for the current silicon revision are rolled into this section at the time of publication. Any errata
found after publication of this document will initially be detailed in a separate errata document until this datasheet is
revised.
7.1. Revision Identification
The Lot ID Code on the top side of the device package can be used for decoding device revision information.
Figures 7.1, 7.2, 7.3, and 7.4 show how to find the Lot ID Code on the top side of the device package.
In addition, firmware can determine the revision of the device by checking the DEVICEID registers.
SiM3C167
BGNZEB
1142
This first character identifies
the device revision
Figure 7.1. LGA-92 SiM3C1x7 Revision Information
SiM3C167
A-GQ
1131BCS701
e3
TW
This character identifies the
device revision
Figure 7.2. TQFP-80 SiM3C1x7 Revision Information
Preliminary Rev. 0.8
87
SiM3C1xx
SiM3C166
BGNZEB
1142
SiM3C166
BGNZEB
1142
This first character identifies
the device revision
Figure 7.3. SiM3C1x6 Revision Information
SIL
M3C164
BGNZ
1142+
This first character identifies
the device revision
Figure 7.4. SiM3C1x4 Revision Information
7.2. Comparator Rising/Falling Edge Flags in Debug Mode (CMP0, CMP1)
7.2.1. Problem
On Revision A and Revision B devices, if the comparator output is high, the comparator rising and falling edge
flags will both be set to 1 upon single-step or exit from debug mode.
7.2.2. Impacts
Firmware using the rising and falling edge flags to make decisions may see a false trigger of the comparator if the
output of the comparator is high during a debug session. This does not impact the non-debug operation of the
device.
7.2.3. Workaround
There is not a system-agnostic workaround for this issue.
7.2.4. Resolution
This issue exists on Revision A and Revision B devices. It may be corrected in a future device revision.
88
Preliminary Rev. 0.8
SiM3C1xx
NOTES:
Preliminary Rev. 0.8
89
SiM3C1xx
CONTACT INFORMATION
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
Please visit the Silicon Labs Technical Support web page:
https://www.silabs.com/support/pages/contacttechnicalsupport.aspx
and register to submit a technical support request.
The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice.
Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from
the use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for the functioning of undescribed features or parameters. Silicon Laboratories reserves the right to make changes without further notice. Silicon Laboratories makes no warranty,
representation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any
liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation
consequential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended
to support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where
personal injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized
application, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages.
Silicon Laboratories, Silicon Labs, and Precision32 are trademarks of Silicon Laboratories Inc.
Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders
90
Preliminary Rev. 0.8