www.ti.com SN74CB3T3257 4-BIT 1-OF-2 FET MULTIPLEXER/DEMULTIPLEXER 2.5-V/3.3-V LOW-VOLTAGE BUS SWITCH WITH 5-V-TOLERANT LEVEL SHIFTER SCDS149 – OCTOBER 2003 – REVISED MARCH 2005 • • • FEATURES • • • • • • • Output Voltage Translation Tracks VCC Supports Mixed-Mode Signal Operation on All Data I/O Ports – 5-V Input Down to 3.3-V Output Level Shift With 3.3-V VCC – 5-V/3.3-V Input Down to 2.5-V Output Level Shift With 2.5-V VCC 5-V-Tolerant I/Os With Device Powered Up or Powered Down Bidirectional Data Flow With Near-Zero Propagation Delay Low ON-State Resistance (ron) Characteristics (ron = 5 Ω Typ) Low Input/Output Capacitance Minimizes Loading (Cio(OFF) = 5 pF Typ) Data and Control Inputs Provide Undershoot Clamp Diodes • • • • • • Low Power Consumption (ICC = 20 µA Max) VCC Operating Range From 2.3 V to 3.6 V Data I/Os Support 0- to 5-V Signaling Levels (0.8 V, 1.2 V, 1.5 V, 1.8 V, 2.5 V, 3.3 V, 5 V) Control Inputs Can Be Driven by TTL or 5-V/3.3-V CMOS Outputs Ioff Supports Partial-Power-Down Mode Operation Latch-Up Performance Exceeds 250 mA Per JESD 17 ESD Performance Tested Per JESD 22 – 2000-V Human-Body Model (A114-B, Class II) – 1000-V Charged-Device Model (C101) Supports Digital Applications: Level Translation, USB Interface, Memory Interleaving, Bus Isolation Ideal for Low-Power Portable Equipment DGV OR PW PACKAGE (TOP VIEW) S 1B1 1B2 1A 2B1 2B2 2A GND 1 16 2 15 3 14 4 13 5 12 6 7 11 10 8 9 VCC OE 4B1 4B2 4A 3B1 3B2 3A DESCRIPTION/ORDERING INFORMATION The SN74CB3T3257 is a high-speed TTL-compatible FET multiplexer/demultiplexer with low ON-state resistance (ron), allowing for minimal propagation delay. The device fully supports mixed-mode signal operation on all data I/O ports by providing voltage translation that tracks VCC. The SN74CB3T3257 supports systems using 5-V TTL, 3.3-V LVTTL, and 2.5-V CMOS switching standards, as well as user-defined switching levels (see Figure 1). ORDERING INFORMATION PACKAGE (1) TA –40°C to 85°C TSSOP – PW TVSOP – DGV (1) ORDERABLE PART NUMBER Tube SN74CB3T3257PW Tape and reel SN74CB3T3257PWR Tape and reel SN74CB3T3257DGVR TOP-SIDE MARKING KS257 KS257 Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2003–2005, Texas Instruments Incorporated SN74CB3T3257 4-BIT 1-OF-2 FET MULTIPLEXER/DEMULTIPLEXER 2.5-V/3.3-V LOW-VOLTAGE BUS SWITCH WITH 5-V-TOLERANT LEVEL SHIFTER www.ti.com SCDS149 – OCTOBER 2003 – REVISED MARCH 2005 DESCRIPTION/ORDERING INFORMATION (CONTINUED) The SN74CB3T3257 is a 4-bit 1-of-2 multiplexer/demultiplexer with a single output-enable (OE) input. The select (S) input controls the data path of the multiplexer/demultiplexer. When OE is low, the multiplexer/demultiplexer is enabled, and the A port is connected to the B port, allowing bidirectional data flow between ports. When OE is high, the multiplexer/demultiplexer is disabled, and a high-impedance state exists between the A and B ports. This device is fully specified for partial-power-down applications using Ioff. The Ioff feature ensures that damaging current will not backflow through the device when it is powered down. The device has isolation during power off. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. FUNCTION TABLE (EACH MULTIPLEXER/DEMULTIPLEXER) INPUTS S INPUT/OUTPUT A FUNCTION L L B1 A port = B1 port L H B2 A port = B2 port H X Z Disconnect OE VCC 5.5 V VCC IN ≈VCC – 1 V ≈VCC OUT ≈VCC – 1 V CB3T 0V 0V Input Voltages Output Voltages NOTE A: If the input high voltage (VIH) level is greater than or equal to VCC – 1 V, and less than or equal to 5.5 V, then the output high voltage (VOH) level will be equal to approximately the VCC voltage level. Figure 1. Typical DC Voltage Translation Characteristics 2 www.ti.com SN74CB3T3257 4-BIT 1-OF-2 FET MULTIPLEXER/DEMULTIPLEXER 2.5-V/3.3-V LOW-VOLTAGE BUS SWITCH WITH 5-V-TOLERANT LEVEL SHIFTER SCDS149 – OCTOBER 2003 – REVISED MARCH 2005 LOGIC DIAGRAM (POSITIVE LOGIC) 4 1A 2 1B1 SW 3 1B2 SW 7 2A 5 2B1 SW 6 2B2 SW 3A 9 11 SW 3B1 10 SW 12 4A 3B2 14 4B1 SW 13 SW 4B2 1 S 15 OE SIMPLIFIED SCHEMATIC, EACH FET SWITCH (SW) A B VG(1) Control Circuit EN(2) (1) Gate voltage (VG) is equal to approximately VCC + VT when the switch is ON and VI > VCC + VT. (2) EN is the internal enable signal applied to the switch. 3 SN74CB3T3257 4-BIT 1-OF-2 FET MULTIPLEXER/DEMULTIPLEXER 2.5-V/3.3-V LOW-VOLTAGE BUS SWITCH WITH 5-V-TOLERANT LEVEL SHIFTER www.ti.com SCDS149 – OCTOBER 2003 – REVISED MARCH 2005 Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN MAX VCC Supply voltage range –0.5 7 V VIN Control input voltage range (2) (3) –0.5 7 V VI/O Switch I/O voltage range (2) (3) (4) IIK Control input clamp current VIN < 0 –50 mA II/OK I/O port clamp current VI/O < 0 –50 mA ±128 mA ±100 mA IIO ON-state switch –0.5 7 current (5) Continuous current through VCC or GND θJA Package thermal impedance (6) Tstg Storage temperature range (1) (2) (3) (4) (5) (6) UNIT DGV package 120 PW package 108 –65 V °C/W °C 150 Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltages are with respect to ground, unless otherwise specified. The input and output voltage ratings may be exceeded if the input and output clamp-current ratings are observed. VI and VO are used to denote specific conditions for VI/O. II and IO are used to denote specific conditions for II/O. The package thermal impedance is calculated in accordance with JESD 51-7. Recommended Operating Conditions (1) VCC Supply voltage VIH High-level control input voltage VIL Low-level control input voltage VI/O Data input/output voltage TA Operating free-air temperature (1) 4 MIN MAX UNIT 2.3 3.6 VCC = 2.3 V to 2.7 V 1.7 5.5 V VCC = 2.7 V to 3.6 V 2 5.5 VCC = 2.3 V to 2.7 V 0 0.7 VCC = 2.7 V to 3.6 V 0 0.8 0 5.5 V –40 85 °C V V All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. www.ti.com SN74CB3T3257 4-BIT 1-OF-2 FET MULTIPLEXER/DEMULTIPLEXER 2.5-V/3.3-V LOW-VOLTAGE BUS SWITCH WITH 5-V-TOLERANT LEVEL SHIFTER SCDS149 – OCTOBER 2003 – REVISED MARCH 2005 Electrical Characteristics (1) over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS VIK VCC = 3 V, II = –18 mA VOH See Figures 3 and 4 IIN Control inputs MIN VCC = 3.6 V, VIN = 3.6 V to 5.5 V or GND Ioff VCC = 0, VO = 0 to 5.5 V, VI = 0 ICC VCC = 3.6 V, II/O = 0, Switch ON or OFF, VIN = VCC or GND 20 VCC = 3 V to 3.6 V, One input at VCC – 0.6 V, Other inputs at VCC or GND VCC = 3.3 V, VIN = VCC or GND ron (5) (1) (2) (3) (4) (5) µA 20 Control inputs B port µA 10 VI = 5.5 V Control inputs Cio(ON) ±10 VI = VCC or GND Cin 300 3 µA pF 5 VI/O = 5.5 V or 3.3 V µA pF 7 VCC = 3.3 V, VI/O = 5.5 V, 3.3 V, or GND, Switch OFF, VIN = VCC or GND VCC = 3.3 V, Switch ON, VIN = VCC or GND µA ±5 VI = 0 to 0.7 V ∆ICC (4) A port µA –40 VCC = 3.6 V, VO = 0 to 5.5 V, VI = 0, Switch OFF, VIN = VCC or GND B port ±10 VI = 0.7 V to VCC – 0.7 V IOZ (3) A port V ±20 VCC = 3.6 V, Switch ON, VIN = VCC or GND UNIT –1.2 VI = VCC – 0.7 V to 5.5 V II Cio(OFF) TYP (2) MAX 6 VI/O = GND 16 VI/O = 5.5 V or 3.3 V pF 4 VI/O = GND 16 VCC = 2.3 V, TYP at VCC = 2.5 V, VI = 0 IO = 24 mA 5 8 IO = 16 mA 5 8 VCC = 3 V, VI = 0 IO = 64 mA 5 7 IO = 32 mA 5 7 Ω VIN and IIN refer to control inputs. VI, VO, II, and IO refer to data pins. All typical values are at VCC = 3.3 V (unless otherwise noted), TA = 25°C. For I/O ports, the parameter IOZ includes the input leakage current. This is the increase in supply current for each input that is at the specified TTL voltage level, rather than VCC or GND. Measured by the voltage drop between A and B terminals at the indicated current through the switch. ON-state resistance is determined by the lower of the voltages of the two (A or B) terminals. Switching Characteristics over recommended operating free-air temperature range (unless otherwise noted) (see Figure 2) VCC = 3.3 V ± 0.3 V TO (OUTPUT) tpd (1) A or B B or A 0.25 ns tpd(s) S A 1 9.5 1 7 ns S B 1 9 1 7.5 OE A or B 1 9 1 7.5 S B 1 7 1 7.5 OE A or B 1 6 1 8 ten tdis (1) VCC = 2.5 V ± 0.2 V FROM (INPUT) PARAMETER MIN MAX MIN 0.15 UNIT MAX ns ns The propagation delay is the calculated RC time constant of the typical ON-state resistance of the switch and the specified load capacitance, when driven by an ideal voltage source (zero output impedance). 5 SN74CB3T3257 4-BIT 1-OF-2 FET MULTIPLEXER/DEMULTIPLEXER 2.5-V/3.3-V LOW-VOLTAGE BUS SWITCH WITH 5-V-TOLERANT LEVEL SHIFTER www.ti.com SCDS149 – OCTOBER 2003 – REVISED MARCH 2005 PARAMETER MEASUREMENT INFORMATION VCC Input Generator VIN 50 Ω 50 Ω VG1 TEST CIRCUIT DUT 2 × VCC Input Generator S1 RL VO VI 50 Ω 50 Ω VG2 CL (see Note A) RL TEST VCC S1 RL VI CL tpd(s) 2.5 V ± 0.2 V 3.3 V ± 0.3 V Open Open 500 Ω 500 Ω 3.6 V or GND 5.5 V or GND 30 pF 50 pF tPLZ/tPZL 2.5 V ± 0.2 V 3.3 V ± 0.3 V 2 × VCC 2 × VCC 500 Ω 500 Ω GND GND 30 pF 50 pF 0.15 V 0.3 V tPHZ/tPZH 2.5 V ± 0.2 V 3.3 V ± 0.3 V Open Open 500 Ω 500 Ω 3.6 V 5.5 V 30 pF 50 pF 0.15 V 0.3 V V∆ VCC Output Control (VIN) VCC/2 VCC VCC/2 VCC/2 0V tPLH VOH Output VCC/2 VCC/2 VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES (tpd(s)) Output Waveform 1 S1 at 2 × VCC (see Note B) tPLZ VCC VCC/2 VOL + V∆ VOL tPZH tPHL VCC/2 0V tPZL Output Control (VIN) Open GND Output Waveform 2 S1 at Open (see Note B) tPHZ VOH VCC/2 VOH − V∆ 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time, with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd(s). The tpd propagation delay is the calculated RC time constant of the typical ON-state resistance of the switch and the specified load capacitance, when driven by an ideal voltage source (zero output impedance). H. All parameters and waveforms are not applicable to all devices. Figure 2. Test Circuit and Voltage Waveforms 6 SN74CB3T3257 4-BIT 1-OF-2 FET MULTIPLEXER/DEMULTIPLEXER 2.5-V/3.3-V LOW-VOLTAGE BUS SWITCH WITH 5-V-TOLERANT LEVEL SHIFTER www.ti.com SCDS149 – OCTOBER 2003 – REVISED MARCH 2005 TYPICAL CHARACTERISTICS OUTPUT VOLTAGE vs INPUT VOLTAGE OUTPUT VOLTAGE vs INPUT VOLTAGE 3.0 4.0 VCC = 2.3 V IO = 1 µA TA = 25°C V - Output Voltage - V O V - Output Voltage - V O 4.0 2.0 1.0 0.0 0.0 1.0 2.0 3.0 4.0 VI - Input Voltage - V 5.0 6.0 3.0 VCC = 3 V IO = 1 µA TA = 25°C 2.0 1.0 0.0 0.0 1.0 2.0 3.0 4.0 5.0 6.0 VI - Input Voltage - V Figure 3. Data Output Voltage vs Data Input Voltage 7 SN74CB3T3257 4-BIT 1-OF-2 FET MULTIPLEXER/DEMULTIPLEXER 2.5-V/3.3-V LOW-VOLTAGE BUS SWITCH WITH 5-V-TOLERANT LEVEL SHIFTER SCDS149 – OCTOBER 2003 – REVISED MARCH 2005 www.ti.com TYPICAL CHARACTERISTICS OUTPUT VOLTAGE HIGH vs SUPPLY VOLTAGE 3.5 4.0 VCC = 2.3 V to 3.6 V VI = 5.5 V TA = 85°C 100 µA 8 mA 16 mA 24 mA 3.0 2.5 2.0 3.5 VCC = 2.3 V to 3.6 V VI = 5.5 V TA = 25°C 8 mA 16 mA 24 mA 3.0 2.5 2.0 2.5 2.7 2.9 3.1 3.3 VCC - Supply Voltage - V 3.5 3.7 2.3 2.5 2.7 2.9 3.1 3.3 VCC - Supply Voltage - V OUTPUT VOLTAGE HIGH vs SUPPLY VOLTAGE V - Output Voltage High - V OH 4.0 3.5 VCC = 2.3 V to 3.6 V VI = 5.5 V TA = -40°C 100 µA 8 mA 16 mA 24 mA 3.0 2.5 2.0 1.5 2.3 2.5 3.3 2.7 2.9 3.1 VCC - Supply Voltage - V Figure 4. VOH Values 8 100 µA 1.5 1.5 2.3 V - Output Voltage High - V OH V - Output Voltage High - V OH 4.0 OUTPUT VOLTAGE HIGH vs SUPPLY VOLTAGE 3.5 3.7 3.5 3.7 PACKAGE OPTION ADDENDUM www.ti.com 30-Mar-2005 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty SN74CB3T3257DGVR ACTIVE TVSOP DGV 16 2000 Pb-Free (RoHS) CU NIPDAU Level-1-250C-UNLIM SN74CB3T3257PW ACTIVE TSSOP PW 16 90 Pb-Free (RoHS) CU NIPDAU Level-1-250C-UNLIM SN74CB3T3257PWR ACTIVE TSSOP PW 16 2000 Pb-Free (RoHS) CU NIPDAU Level-1-250C-UNLIM Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 MECHANICAL DATA MPDS006C – FEBRUARY 1996 – REVISED AUGUST 2000 DGV (R-PDSO-G**) PLASTIC SMALL-OUTLINE 24 PINS SHOWN 0,40 0,23 0,13 24 13 0,07 M 0,16 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 0°–8° 1 0,75 0,50 12 A Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,08 14 16 20 24 38 48 56 A MAX 3,70 3,70 5,10 5,10 7,90 9,80 11,40 A MIN 3,50 3,50 4,90 4,90 7,70 9,60 11,20 DIM 4073251/E 08/00 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side. Falls within JEDEC: 24/48 Pins – MO-153 14/16/20/56 Pins – MO-194 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0°– 8° A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2005, Texas Instruments Incorporated