SN75ALS197 QUADRUPLE DIFFERENTIAL LINE RECEIVER SLLS045B – JANUARY 1989 – REVISED MAY 1995 D D D D D D D D D D D D OR N PACKAGE (TOP VIEW) Meets or Exceeds the Requirements of ITU Recommendations V.10, V.11, X.26, and X.27 Designed for Multipoint Bus Transmission on Long Bus Lines in Noisy Environments Designed to Operate Up to 20 Mbaud 3-State Outputs Common-Mode Input Voltage Range – 7 V to 7 V Input Sensitivity . . . ±300 mV Input Hysteresis . . . 120 mV Typ High-Input Impedance . . . 12 kΩ Min Operates from Single 5-V Supply Low Supply-Current Requirement 35 mA Max Improved Speed and Power Consumption Compared to AM26LS32A 1B 1A 1Y G 2Y 2A 2B GND 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 VCC 4B 4A 4Y G 3Y 3A 3B description The SN75ALSI97 is a monolithic, quadruple line receiver with 3-state outputs designed using advanced, low-power, Schottky technology. This technology provides combined improvements in bar design, tooling production, and wafer fabrication. This, in turn, provides significantly lower power requirements and permits much higher data throughput than other designs. The device meets the specifications of ITU Recommendations V.10, V.11, X.26, and X.27. It features 3-state outputs that permit direct connection to a bus-organized system with a fail-safe design that ensures the outputs will always be high if the inputs are open. The device is optimized for balanced, multipoint bus transmission at rates up to 20 megabits per second. The input features high-input impedance, input hysteresis for increased noise immunity, and an input sensitivity of ± 300 mV over a common-mode input voltage range of – 7 V to 7 V. It also features active-high and active-low enable functions that are common to the four channels. The SN75ALS197 is designed for optimum performance when used with the SN75ALS192 quadruple differential line driver. The SN75ALS197 is characterized for operation from 0°C to 70°C. FUNCTION TABLE (each receiver) ENABLES G G OUTPUT Y VID ≥ 0.3 V H X X L H H – 0.3 V < VID < 0.3 V H X X L ? ? VID ≤ – 0.3 V H X X L L L X L H Z Open H X X L H H DIFFERENTIAL INPUTS A–B H = high level, L = low level, X = irrelevant, ? = indeterminate, Z = high impedance (off) Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 1995, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN75ALS197 QUADRUPLE DIFFERENTIAL LINE RECEIVER SLLS045B – JANUARY 1989 – REVISED MAY 1995 logic symbol† G G 1A 1B 2A 2B 3A 3B 4A 4B 4 logic diagram (positive logic) ≥1 G EN 12 4 12 G 2 3 1 1A 1Y 1B 6 5 7 10 11 9 14 13 15 2A 2Y 2B 2 3 1Y 5 2Y 1 6 7 3Y 3A 4Y 3B † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. 4A 4B 10 9 11 3Y 14 13 15 4Y schematics of inputs and outputs EQUIVALENT OF EACH A OR B INPUT EQUIVALENT OF G OR G INPUTS VCC VCC 3 kΩ NOM EQUIVALENT OF ALL OUTPUTS VCC 22 kΩ NOM 50 kΩ NOM 18 kΩ NOM Input Output 300 kΩ NOM VCC (A) or GND (B) Input 2 kΩ NOM GND GND GND 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN75ALS197 QUADRUPLE DIFFERENTIAL LINE RECEIVER SLLS045B – JANUARY 1989 – REVISED MAY 1995 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Input voltage, VI (A or B inputs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±15 V Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±15 V Enable input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Low-level output current, IOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, except differential input voltage, are with respect to network ground terminal. 2. Differential input voltage is measured at the noninverting input with respect to the corresponding inverting input. DISSIPATION RATING TABLE PACKAGE TA ≤ 25°C POWER RATING DERATING FACTOR TA = 70°C POWER RATING D 950 mW 7.6 mW/°C 608 mW N 1150 mW 9.2 mW/°C 736 mW recommended operating conditions MIN Supply voltage, VCC 4.75 Common-mode input voltage, VIC Differential input voltage, VID High-level input voltage, VIH NOM MAX 5 5.25 V ±7 V ±12 V 2 Low-level input voltage, VIL V 0.8 High-level output current, IOH Low-level output current, IOL Operating free-air temperature, TA 0 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 UNIT V –400 µA 16 mA 70 °C 3 SN75ALS197 QUADRUPLE DIFFERENTIAL LINE RECEIVER SLLS045B – JANUARY 1989 – REVISED MAY 1995 electrical characteristics over recommended range of common-mode input voltage, supply voltage, and operating free-air temperature (unless otherwise noted) PARAMETER TEST CONDITIONS VIT+ VIT– Positive-going input threshold voltage Vhys VIK Hysteresis voltage (VIT+ – VIT –) See Figure 4 Enable-input clamp voltage VOH High-level output voltage II = –18 mA VID = 300 mV, MIN TYP† MAX UNIT 300 mV – 300‡ Negative-going input threshold voltage mV 120 mV – 1.5 VOL Low level output voltage Low-level VID = – 300 mV IOZ High impedance state output current High-impedance-state VCC = 5 5.25 25 V II Line input current Other input at 0 V,, See Note 3 IH High level enable High-level enable-input input current IIL Low-level enable-input current IOH = – 400 µA IOL = 8 mA 2.7 3.6 V 0.45 IOL = 16 mA VO = 2.4 V 0.5 VOH = 0.4 V VI = 15 V – 20 20 VI = –15 V VIH = 2.7 V 0.7 1.2 – 1.0 – 1.7 20 100 VIH = 5.25 V VIL = 0.4 V – 100 Input resistance 12 V 18 V µA mA µA µA kΩ IOS Short-circuit output current§ VID = 3 V, VO = 0 – 15 – 78 – 130 mA ICC Supply current Outputs disabled 22 35 mA † All typical values are at VCC = 5 V, TA = 25°C. ‡ The algebraic convention, in which the less positive limit is designated minimum, is used in this data sheet for threshold voltage levels only. § Not more than one output should be shorted at a time, and the duration of the short circuit should not exceed one second. NOTE 3: Refer to ANSI Standard EIA/TIA-422-B and EIA/TIA-423-B for exact conditions. switching characteristics, VCC = 5 V, TA = 25°C PARAMETER TEST CONDITIONS tPLH tPHL Propagation delay time, low- to high-level output tPZH tPZL Output enable time to high level tPHZ tPLZ Output disable time from high level 4 Propagation delay time, high- to low-level output Output enable time to low level Output disable time from low level VID = – 2.5 V to 2.5 V,, See Figure 2 CL = 15 pF,, CL = 15 pF, pF See Figure 3 CL = 15 pF, pF See Figure 3 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MIN TYP MAX UNIT 15 22 ns 15 22 ns 13 25 11 25 13 25 15 22 ns ns SN75ALS197 QUADRUPLE DIFFERENTIAL LINE RECEIVER SLLS045B – JANUARY 1989 – REVISED MAY 1995 PARAMETER MEASUREMENT INFORMATION VID VOH IOL IOH VOL 2V Figure 1. VOH and VOL Test Circuit 2.5 V Generator (see Note A) Input 50 Ω 0V 0V Output CL = 15 pF (see Note B) – 2.5 V tPLH tPHL VOH Output 1.3 V 1.3 V VOL 2V TEST CIRCUIT VOLTAGE WAVEFORMS NOTES: A. The input pulse is supplied by a generator having the following characteristics: PRR ≤ 1 MHz, duty cycle ≤ 50%, ZO = 50 Ω, tr ≤ 6 ns, tf ≤ 6 ns. B. CL includes probe and jig capacitance. Figure 2. tPLH and tPHL Test Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 SN75ALS197 QUADRUPLE DIFFERENTIAL LINE RECEIVER SLLS045B – JANUARY 1989 – REVISED MAY 1995 PARAMETER MEASUREMENT INFORMATION Test Point VCC RL = 2 kΩ S1 From Output Under Test See Note B CL (see Note A) 5 kΩ S2 LOAD CIRCUIT ≤ 5 ns 90% Enable G 10% 1.3 V ≤ 5 ns 3V 90% 1.3 V ≤ 5 ns 10% 0V Enable G 10% 90% 90% 1.3 V 1.3 V 0V See Note C 90% 1.3 V 10% 10% S1 Open S2 Closed 3V 90% Enable G 1.3 V 1.3 V tPHZ ≈ 1.4 V 90% 1.3 V 10% 0V 0.5 V VOH tPZH Output 3V 10% See Note C 90% Enable G 1.3 V ≤ 5 ns 10% tPZL Output S1 Closed S2 Open S1 Closed S2 Closed tPLZ 1.3 V S1 Closed S2 Closed VOLTAGE WAVEFORMS FOR tPHZ and tPZH VOLTAGE WAVEFORMS FOR tPLZ and tPZL Figure 3. tPHZ, tPZH, tPLZ, and tPZL Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 0V ≈ 1.4 V VOL 0.5 V NOTES: A. CL includes probe and jig capacitance. B. All diodes are 1N3064 or equivalent. C. Enable G is tested with G high; G is tested with G low. 6 3V • DALLAS, TEXAS 75265 SN75ALS197 QUADRUPLE DIFFERENTIAL LINE RECEIVER SLLS045B – JANUARY 1989 – REVISED MAY 1995 TYPICAL CHARACTERISTICS OUTPUT VOLTAGE vs ENABLE VOLTAGE OUTPUT VOLTAGE vs ENABLE VOLTAGE 4 5 VID = 300 mV VIC = 0 RL = 8 kΩ to GND TA = 25°C VO – Output Voltage – V 4 TA = 70°C TA = 25°C TA = 0°C 3.5 VCC = 5.5 V VO – Output Voltage – V 4.5 VCC = 5 V 3.5 VCC = 4.5 V 3 2.5 2 1.5 3 2.5 2 1.5 1 VCC = 5 V VID = 300 mV VIC = 0 RL = 8 kΩ to GND 1 0.5 0.5 0 0 0 0.5 1 1.5 2 2.5 0 3 0.5 1 2 2.5 3 Enable Voltage – V Enable Voltage – V Figure 5 Figure 4 OUTPUT VOLTAGE vs ENABLE VOLTAGE OUTPUT VOLTAGE vs ENABLE VOLTAGE 6 6 VCC = 5.5 V VCC = 5 V VID = – 300 mV VIC = 0 RL = 1 kΩ to VCC TA = 25°C VCC = 4.5 V 5 VO – Output Voltage – V 5 VO – Output Voltage – V 1.5 4 3 2 TA = 0°C TA = 25°C 4 TA = 70°C 3 2 VCC = 5 V VID = – 300 mV VIC = 0 RL = 1 kΩ to VCC 1 1 0 0 0 0.5 1 1.5 2 2.5 3 0 0.5 1 1.5 2 2.5 3 Enable Voltage – V Enable Voltage – V Figure 6 Figure 7 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 SN75ALS197 QUADRUPLE DIFFERENTIAL LINE RECEIVER SLLS045B – JANUARY 1989 – REVISED MAY 1995 TYPICAL CHARACTERISTICS OUTPUT VOLTAGE vs DIFFERENTIAL INPUT VOLTAGE HIGH-LEVEL OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE 5 VO – Output Voltage – V 4 4 VCC = 5 V VIC = –12 V to 12 V IO = 0 TA = 25°C IOH = 0 VOH – High-Level Output Voltage – V 4.5 3.5 3 2.5 2 VIT – VIT + 1.5 1 3.5 IOH = – 400 µA 3 2.5 2 1.5 1 VCC = 5 V VID = 300 mV VIC = 0 0.5 0.5 0 – 200 – 150 – 100 – 50 0 50 100 150 0 200 0 10 HIGH-LEVEL OUTPUT VOLTAGE vs HIGH-LEVEL OUTPUT CURRENT 5 VID = 300 mV VIC = 0 TA = 25°C 4.5 4 3.5 VCC = 5.5 V VCC = 5 V 2.5 VCC = 4.5 V 2 1.5 1 VOH – High-Level Output Voltage – V VOH – High-Level Output Voltage – V 40 50 60 70 80 HIGH-LEVEL OUTPUT VOLTAGE vs HIGH-LEVEL OUTPUT CURRENT 5 VCC = 5 V VID = 300 mV VIC = 0 4.5 4 3.5 3 TA = 0°C 2.5 TA = 25°C 2 TA = 70°C 1.5 1 0.5 0.5 0 0 0 – 10 – 20 – 30 – 40 – 50 – 60 – 70 – 80 – 90 – 100 0 – 10 – 20 – 30 –40 – 50 –60 – 70 – 80 – 90 – 100 IOH – High-Level Output Current – mA IOH – High-Level Output Current – mA Figure 10 8 30 Figure 9 Figure 8 3 20 TA – Free-Air Temperature – °C VID – Differential Input Voltage – mV Figure 11 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN75ALS197 QUADRUPLE DIFFERENTIAL LINE RECEIVER SLLS045B – JANUARY 1989 – REVISED MAY 1995 TYPICAL CHARACTERISTICS LOW-LEVEL OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE VOL – Low-Level Output Volatge – V 0.4 VCC = 5 V VID = – 300 mV VIC = 0 0.35 0.3 0.25 IO = 8 mA 0.2 0.15 IO = 0 0.1 0.05 0 0 10 20 30 40 50 60 70 80 TA – Free-Air Temperature – °C Figure 12 LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT 0.8 VCC = 4.5 V 0.7 VOL – Low-Level Output Voltage – V VOL – Low-Level Output Voltage – V 0.8 VCC = 5 V 0.6 VCC = 5.5 V 0.5 0.4 0.3 0.2 VID = – 300 mV VIC = 0 TA = 25°C 0.1 TA = 70°C 0.7 TA = 25°C 0.6 TA = 0°C 0.5 0.4 0.3 0.2 VCC = 5 V VID = – 300 mV VIC = 0 0.1 0 0 0 10 20 30 40 50 60 70 80 IOL – Low-Level Output Current – mA 0 10 20 30 40 50 60 70 80 IOL – Low-Level Output Current – mA Figure 14 Figure 13 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 SN75ALS197 QUADRUPLE DIFFERENTIAL LINE RECEIVER SLLS045B – JANUARY 1989 – REVISED MAY 1995 TYPICAL CHARACTERISTICS SUPPLY CURRENT vs SUPPLY VOLTAGE 50 VID = – 300 mV VIC = 0 IO= 0 TA = 25°C 40 30 I CC – Supply Current – mA 45 I CC – Supply Current – mA SUPPLY CURRENT vs FREE-AIR TEMPERATURE 35 30 Disabled 25 Enabled 20 15 VCC = 5.5 V 25 VCC = 5 V 20 VCC = 4.5 V 15 10 10 VID = – 300 mV Outputs Enabled IO = 0 5 5 0 1 0 3 2 4 5 6 7 0 8 0 10 VCC – Supply Voltage – V 20 30 50 60 70 80 TA – Free-Air Temperature – °C Figure 16 Figure 15 SUPPLY CURRENT vs FREQUENCY SUPPLY CURRENT vs DIFFERENTIAL INPUT VOLTAGE 40 30 35 VCC = 5.5 V 25 I CC – Supply Current – mA I CC – Supply Current – mA 40 VCC = 5 V 20 VCC = 4.5 V 15 10 30 VCC = 5 V VI = ± 1.5-V Square Wave CL = 15 pF Four Channels Driven TA = 25°C 25 20 15 10 5 IO = 0 Outputs Enabled VIC = 0 TA = 25°C 0 – 200 – 100 5 0 100 200 0 10 k 1M f – Frequency – Hz VID – Differential Input Voltage – mV Figure 17 10 100 k Figure 18 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 10 M 100 M SN75ALS197 QUADRUPLE DIFFERENTIAL LINE RECEIVER SLLS045B – JANUARY 1989 – REVISED MAY 1995 TYPICAL CHARACTERISTICS INPUT CURRENT vs INPUT VOLTAGE TO GND INPUT RESISTANCE vs FREE-AIR TEMPERATURE 3 30 TA = 25°C 2 I I – Input Current – mA rI – Input Resistance – k Ω 25 20 15 10 1 0 –1 5 –2 0 –3 – 20 0 10 20 30 40 50 60 70 80 – 15 TA – Free-Air Temperature – °C – 10 –5 5 10 15 20 VI – Input Voltage to GND – V Figure 19 Figure 20 PROPAGATION DELAY TIME vs SUPPLY VOLTAGE SWITCHING TIME vs FREE-AIR TEMPERATURE 20 30 VCC = 5 V CL = 15 pF 18 tPLH tpd – Propagation Delay Time – ns 25 tPLZ Switching Time – ns 0 20 tPHZ tPZH 15 tPHL 10 tPZL tPHZ tPZH CL = 15 pF TA = 25°C 16 tPHL 14 tPLH 12 10 8 6 4 5 2 0 0 10 20 30 40 50 60 70 80 0 4.5 4.6 4.7 TA – Free-Air Temperature – °C 4.8 4.9 5 5.1 5.2 5.3 5.4 5.5 VCC – Supply Voltage – V Figure 21 Figure 22 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 11 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1998, Texas Instruments Incorporated