® SP7651 Advanced Wide Input Voltage Range 3A, 900kHz, Buck Regulator SP7651 FEATURES ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ DFN PACKAGE 7mm x 4mm 2.5V to 20V Step Down Achieved Using Dual Input Output Voltage down to 0.8V 3A Output Capability (Up to 5A with Air Flow) Built in Low RDSON Power FETs (40 mΩ typ) Highly Integrated Design, Minimal Components 900 kHz Fixed Frequency Operation UVLO Detects Both VCC and VIN Over Temperature Protection Short Circuit Protection with Auto-Restart Wide BW Amp Allows Type II or III Compensation Programmable Soft Start Fast Transient Response High Efficiency: Greater than 92% Possible Asynchronous Start-Up into a Pre-Charged Output Small 7mm x 4mm DFN Package PGND 1 26 LX TOP VIEW PGND 2 Heatsink Pad 1 Connect to Lx PGND 3 25 LX 24 LX GND 4 23 LX VFB 5 2 2 VCC COMP 6 21 GND Heatsink pad 2 Connect to GND UVIN 7 20 GND GND 8 19 GND SS 9 18 BST VIN 10 VIN 11 17 NC Heatsink pad 3 Connect to V IN 16 LX VIN 12 15 LX VIN 13 14 LX Now Available in Lead Free Packaging DESCRIPTION The SP7651 is a high voltage synchronous step-down switching regulator optimized for high efficiency. The part is designed to be especially attractive for dual supply, 12V step down with 5V used to power the controller. This lower VCC voltage minimizes power dissipation in the part. The SP7651 is designed to provide a fully integrated buck regulator solution using a fixed 900kHz frequency, PWM voltage mode architecture. Protection features include UVLO, thermal shutdown and output short circuit protection. The SP7651 is available in the space saving 7mm X 4mm DFN package. TYPICAL APPLICATION CIRCUIT U1 SP7651 1 CZ2 2 RZ2 3 1,000pF 15k,1% CP1 5 22pF CF1 4 6 ENABLE 100pF 7 8 9 CSS 10 15nF 11 12 13 VIN 12V C1 Date: 08/25/04 L1 LX PGND LX PGND LX GND LX VFB VCC COMP GND UVIN GND GND GND SS BST VIN NC VIN LX VIN LX VIN LX 26 4.7uH, Irate=3.87A 25 RZ3 24 C3 23 22uF 6.3V 22 21 7.15k,1% CZ3 VOUT 3.3V 0-3A R1 68.1k,1% 150pF CVCC 2.2uF 20 19 DBST 18 SD101AWS 17 16 RSET 21.5k,1% (note 2) CBST 15 6800pF 14 +5V VCC fs=900Khz 22uF 16V GND PGND Notes: 1. U1 Bottom-Side Layout should has three contacts isolated from one another Vin SWNODE and GND 2. RSET=54.48/(Vout-0.8V) (KOhm) SP7651 Wide Input Voltage Range 3A, 900kHz, Buck Regulator 1 © Copyright 2004 Sipex Corporation ABSOLUTE MAXIMUM RATINGS These are stress ratings only and functional operation of the device at these ratings or any other above those indicated in the operation sections of the specifications below is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. GH ......................................................................... -0.3V to BST+0.3V GH-SWN ......................................................................................... 7V All other pins .......................................................... -0.3V to VCC+0.3V VCC .................................................................................................. 7V VIN ........................................................................................................................................... 22V ILX ............................................................................................................................................... 5A BST ............................................................................................... 35V BST-SWN ......................................................................... -0.3V to 7V SWN ................................................................................... -1V to 20V Storage Temperature .................................................. -65°C to 150°C Power Dissipation .................................................... Internally Limited Lead Temperature (Soldering, 10 sec) ...................................... 300°C ESD Rating .......................................................................... 2kV HBM Thermal Resistance ϑJC .................................................................................... 5°C/W ELECTRICAL SPECIFICATIONS Unless otherwise specified: -40°C < TAMB < 85°C, -40°C<Tj<125°C, 4.5V < VCC < 5.5V, 3V<Vin<20V, BST=LX + 5V, LX = GND = 0V, UVIN = 3.0V, CVCC = 1µF, CCOMP = 0.1µF, CSS = 50nF, Typical measured at VCC = 5V. The ♦ denotes the specifications which apply over the full temperature range, unless otherwise specified. PARAMETER MIN. TYP. MAX. UNITS VCC Supply Current (No switching) 1.5 3 mA VCC Supply Current (switching) 16 TBD mA BST Supply Current (No switching) 0.2 0.4 mA 8 TBD mA CONDITIONS QUIESCENT CURRENT BST Supply Current (switching) VFB =0.9V ♦ VFB =0.9V ♦ PROTECTION: UVLO VCC UVLO Start Threshold 4.00 4.25 4.5 V VCC UVLO Hysteresis 100 200 300 mV UVIN Start Threshold 2.3 2.5 2.65 V UVIN Hysteresis 200 300 400 mV 1 µA UVIN Input Current ♦ UVIN= 3.0V ERROR AMPLIFIER REFERENCE Error Amplifier Reference 0.792 0.800 0.808 V Error Amplifier Reference Over Line and Temperature 0.788 0.800 0.812 V 2X Gain Config., Measure VFB; VCC =5 V, T=25ºC ♦ Error Amplifier Transconductance 6 mA/V Error Amplifier Gain 60 dB No Load COMP Sink Current 150 µA VFB =0.9V, COMP= 0.9V COMP Source Current 150 µA VFB =0.7V, COMP= 2.2V VFB Input Bias Current 50 nA VFB = 0.8V Internal Pole 4 MHz COMP Clamp 2.5 V COMP Clamp Temp. Coefficient -2 mV/ºC Date: 08/25/04 200 SP7651 Wide Input Voltage Range 3A, 900kHz, Buck Regulator 2 VFB =0.7V, TA=25ºC © Copyright 2004 Sipex Corporation ELECTRICAL SPECIFICATIONS Unless otherwise specified: -40°C < TAMB < 85°C, -40°C<Tj<125°C, 4.5V < VCC < 5.5V, 3V<Vin<20V, BST=LX + 5V, LX = GND = 0V, UVIN = 3.0V, CVCC = 1µF, CCOMP = 0.1µF, CSS = 50nF, Typical measured at VCC = 5V. The ♦ denotes the specifications which apply over the full temperature range, unless otherwise specified. PARAMETER MIN. TYP. MAX. UNITS CONDITIONS CONTROL LOOP: PWM COMPARATOR, RAMP & LOOP DELAY PATH Ramp Amplitude 0.92 1.1 1.28 V RAMP Offset 1.1 V RAMP Offset Temp. Coefficient -2 mV/ºC GH Minimum Pulse Width 90 Maximum Controllable Duty Ratio 92 Maximum Duty Ratio 100 Internal Oscillator Ratio 81 0 180 97 900 990 ns TA = 25ºC, RAMP COMP until GH starts Switching ♦ % Maximum Duty Ratio Measured just before pulsing begins % Valid for 20 cycles kHz ♦ TIMERS: SOFTSTART SS Charge Current: 10 SS Discharge Current: µA 1 mA ♦ Fault Present, SS = 0.2V V ♦ Measured VREF (0.8V) VFB PROTECTION: Short Circuit & Thermal Short Circuit Threshold Voltage 0.2 0.25 0.3 Hiccup Timeout 200 ms VFB = 0.5V Number of Allowable Clock Cycles at 100% Duty Cycle 20 Cycles Minimum GL Pulse After 20 Cycles 0.5 Cycles VFB = 0.7V Thermal Shutdown Temperature 14 5 ºC VFB = 0.7V Thermal Recovery Temperature 13 5 ºC Thermal Hysteresis 10 ºC High Side RDSON 40 mΩ VCC = 5V ; IOUT = 3A TAMB = 25ºC Synchronous FET RDSON 40 mΩ VCC = 5V ; IOUT = 3A TAMB = 25ºC OUTPUT: POWER STAGE Maximum Output Current Date: 08/25/04 3 A SP7651 Wide Input Voltage Range 3A, 900kHz, Buck Regulator 3 © Copyright 2004 Sipex Corporation PIN DESCRIPTION Pin # Pin Name Description 1-3 PGND Ground connection for the synchronous rectifier 4,8,19-21 GND Ground Pin. The control circuitry of the IC and lower power driver are referenced to this pin. Return separately from other ground traces to the (-) terminal of Cout. 5 VFB Feedback Voltage and Short Circuit Detection pin. It is the inverting input of the Error Amplifier and serves as the output voltage feedback point for the Buck Converter. The output voltage is sensed and can be adjusted through an external resistor divider. Whenever VFB drops 0.25V below the positive reference, a short circuit fault is detected and the IC enters hiccup mode. 6 COMP Output of the Error Amplifier. It is internally connected to the inverting input of the PWM comparator. An optimal filter combination is chosen and connected to this pin and either ground or VFB to stabilize the voltage mode loop. 7 UVIN 9 SS Soft Start. Connect an external capacitor between SS and GND to set the soft start rate based on the 10µA source current. The SS pin is held low via a 1mA (min) current during all fault conditions. 10-13 VIN Input connection to the high side N-channel MOSFET. Place a decoupling capacitor between this pin and PGND. 14-16,23-26 LX Connect an inductor between this pin and VOUT 22 VCC Input for external 5V bias supply 17 NC No Connect UVLO input for Vin voltage. Connect a resistor divider between VIN and UVIN to set minimum operating voltage THEORY OF OPERATION General Overview The SP7651 is a fixed frequency, voltage mode, synchronous PWM regulator optimized for high efficiency. The part has been designed to be especially attractive for split plane applications utilizing 5V to power the controller and 2.5V to 28V for step down conversion. The SP7651 contains two unique control features that are very powerful in distributed applications. First, asynchronous driver control is enabled during start up, to prohibit the low side NFET from pulling down the output until the high side NFET has attempted to turn on. Second, a 100% duty cycle timeout ensures that the low side NFET is periodically enhanced during extended periods at 100% duty cycle. This guarantees the synchronized refreshing of the BST capacitor during very large duty ratios. The heart of the SP7651 is a wide bandwidth transconductance amplifier designed to accommodate Type II and Type III compensation schemes. A precision 0.8V reference, present on the positive terminal of the error amplifier permits the programming of the output voltage down to 0.8V via the VFB pin. The output of the error amplifier, COMP, which is compared to a 1.1V peak-to-peak ramp is responsible for trailing edge PWM control. This voltage ramp, and PWM control logic are governed by the internal oscillator that accurately sets the PWM frequency to 900kHz. Date: 08/25/04 The SP7651 also contains a number of valuable protection features. Programmable UVLO allows the user to set the exact VIN value at which the conversion voltage can safely begin down conversion, and an internal VCC UVLO ensures that the controller itself has enough voltage to properly operate. Other protection features in- SP7651 Wide Input Voltage Range 3A, 900kHz, Buck Regulator 4 © Copyright 2004 Sipex Corporation THEORY OF OPERATION Thermal and Short-Circuit Protection clude thermal shutdown and short-circuit detection. In the event that either a thermal, shortcircuit, or UVLO fault is detected, the SP7651 is forced into an idle state where the output drivers are held off for a finite period before a re-start is attempted. Because the SP7651 is designed to drive large output current, there is a chance that the power converter will become too hot. Therefore, an internal thermal shutdown (145°C) has been included to prevent the IC from malfunctioning at extreme temperatures. Soft Start “Soft Start” is achieved when a power converter ramps up the output voltage while controlling the magnitude of the input supply source current. In a modern step down converter, ramping up the positive terminal of the error amplifier controls soft start. As a result, excess source current can be defined as the current required to charge the output capacitor. A short-circuit detection comparator has also been included in the SP7651 to protect against an accidental short at the output of the power converter. This comparator constantly monitors the positive and negative terminals of the error amplifier, and if the VFB pin falls more than 250mV (typical) below the positive reference, a short-circuit fault is set. Because the SS pin overrides the internal 0.8V reference during soft start, the SP7651 is capable of detecting shortcircuit faults throughout the duration of soft start as well as in regular operation. IVIN = COUT * (DVOUT / DTSOFT-START) The SP7651 provides the user with the option to program the soft start rate by tying a capacitor from the SS pin to GND. The selection of this capacitor is based on the 10uA pull up current present at the SS pin and the 0.8V reference voltage. Therefore, the excess source can be redefined as: Handling of Faults: Upon the detection of power (UVLO), thermal, or short-circuit faults, the SP7651 is forced into an idle state where the SS and COMP pins are pulled low and the NFETS are held off. In the event of UVLO fault, the SP7651 remains in this idle state until the UVLO fault is removed. Upon the detection of a thermal or short-circuit fault, an internal 200ms timer is activated. In the event of a short-circuit fault, a re-start is attempted immediately after the 200ms timeout expires. Whereas, when a thermal fault is detected the 200ms delay continuously recycles and a re-start cannot be attempted until the thermal fault is removed and the timer expires. IVIN = COUT * (DVOUT *10µA / (CSS * 0.8V) Under Voltage Lock Out (UVLO) The SP7651 contains two separate UVLO comparators to monitor the internal bias (VCC) and conversion (VIN) voltages independently. The VCC UVLO threshold is internally set to 4.25V, whereas the VIN UVLO threshold is programmable through the UVIN pin. When the UVIN pin is greater than 2.5V, the SP7651 is permitted to start up pending the removal of all other faults. Both the VCC and VIN UVLO comparators have been designed with hysteresis to prevent noise from resetting a fault. Date: 08/25/04 Error Amplifier and Voltage Loop Since the heart of the SP7651 voltage error loop is a high performance, wide bandwidth transconductance amplifier great care should be taken to select the optimal compensation network. Because of the amplifier’s current limited (+/-150µA) transconductance, there are many ways to compensate the voltage loop or to SP7651 Wide Input Voltage Range 3A, 900kHz, Buck Regulator 5 © Copyright 2004 Sipex Corporation THEORY OF OPERATION control the COMP pin externally. If a simple, single pole, single zero response is desired, then compensation can be as simple as an RC to ground. If a more complex compensation is required, then the amplifier has enough bandwidth (45° at 4 MHz) and enough gain (60dB) to run Type III compensation schemes with adequate gain and phase margins at cross over frequencies greater than 50kHz. VBST GH Voltage VSWN V(VCC) GL Voltage 0V V(VIN) The common mode output of the error amplifier is 0.9V to 2.2V. Therefore, the PWM voltage ramp has been set between 1.1V and 2.2V to ensure proper 0% to 100% duty cycle capability. The voltage loop also includes two other very important features. One is asynchronous start up mode. Basically, the synchronous rectifier can not turn on unless the high side NFET has attempted to turn on or the SS pin has exceeded 1.7V. This feature prevents the controller from “dragging down” the output voltage during startup or in fault modes. The second feature is a 100% duty cycle timeout that ensures synchronized refreshing of the BST capacitor at very high duty ratios. In the event that the high side NFET is on for 20 continuous clock cycles, a reset is given to the PWM flip flop half way through the 21st cycle. This forces GL to rise for the cycle, in turn refreshing the BST capacitor. SWN Voltage -0V -V(Diode) V V(VIN)+V(VCC) BST Voltage V(VCC) TIME Setting Output Voltages The SP7651 can be set to different output voltages. The relationship in the following formula is based on a voltage divider from the output to the feedback pin VFB, which is set to an internal reference voltage of 0.80V. Standard 1% metal film resistors of surface mount size 0603 are recommended. Power MOSFETs The SP7651 contains a pair of integrated low resistance N MOSFETs designed to drive up to 3A of output current. Maximum output current could be limited by thermal limitations of a particular application. The SP7651 incorporates a built-in over-temperature protection to prevent internal overheating. Date: 08/25/04 Vout = 0.80V ( R1 / R2 + 1 ) => R2 = R1 / [ ( Vout / 0.80V ) – 1 ] Where R1 = 68.1KΩ and for Vout = 0.80V setting, simply remove R2 from the board. Furthermore, one could select the value of R1 and R2 combination to meet the exact output voltage setting by restricting R1 resistance range such that 50KΩ < R1 < 100KΩ for overall system loop stability. SP7651 Wide Input Voltage Range 3A, 900kHz, Buck Regulator 6 © Copyright 2004 Sipex Corporation APPLICATIONS INFORMATION saturate at the peak inductor current Inductor Selection There are many factors to consider in selecting the inductor including core material, inductance vs. frequency, current handling capability, efficiency, size and EMI. In a typical SP7651 circuit, the inductor is chosen primarily by operating frequency, saturation current and DC resistance. Increasing the inductor value will decrease output voltage ripple, but degrade transient response. Low inductor values provide the smallest size, but cause large ripple currents, poor efficiency and more output capacitance to smooth out the larger ripple current. The inductor must be able to handle the peak current at the switching frequency without saturating, and the copper resistance in the winding should be kept as low as possible to minimize resistive power loss. A good compromise between size, loss and cost is to set the inductor ripple current to be within 20% to 40% of the maximum output current. I PEAK = I OUT (max) + and provide low core loss at the high switching frequency. Low cost powdered iron cores are inappropriate for 900kHz operation. Gapped ferrite inductors are widely available for consideration. Select devices that have operating data shown up to 1MHz. Ferrite materials, on the other hand, are more expensive and have an abrupt saturation characteristic with the inductance dropping sharply when the peak design current is exceeded. Nevertheless, they are preferred at high switching frequencies because they present very low core loss and the design only needs to prevent saturation. In general, ferrite or molyperm alloy materials will be used with the SP7651. Optimizing Efficiency The switching frequency and the inductor operating point determine the inductor value as follows: L= The power dissipated in the inductor is equal to the sum of the core and copper losses. To minimize copper losses, the winding resistance needs to be minimized, but this usually comes at the expense of a larger inductor. Core losses have a more significant contribution at low output current where the copper losses are at a minimum, and can typically be neglected at higher output currents where the copper losses dominate. Core loss information is usually available from the magnetic vendor. Proper inductor selection can affect the resulting power supply efficiency by more than 15-20%! VOUT (V IN (max) − VOUT ) VIN (max) FS Kr I OUT ( max) where: Fs = switching frequency Kr = ratio of the ac inductor ripple current to the maximum output current The copper loss in the inductor can be calculated using the following equation: The peak to peak inductor ripple current is: I PP = PL( Cu) = I L2 ( RMS ) RWINDING VOUT (VIN (max) − VOUT ) where IL(RMS) is the RMS inductor current that can be calculated as follows: VI N (max) FS L IL(RMS) = IOUT(max) 1 + 1 3 Once the required inductor value is selected, the proper selection of core material is based on peak inductor current and efficiency requirements. The core must be large enough not to Date: 08/25/04 I PP 2 SP7651 Wide Input Voltage Range 3A, 900kHz, Buck Regulator 7 ( IPP IOUT(max) ) 2 © Copyright 2004 Sipex Corporation APPLICATIONS INFORMATION Output Capacitor Selection The required ESR (Equivalent Series Resistance) and capacitance drive the selection of the type and quantity of the output capacitors. The ESR must be small enough that both the resistive voltage deviation due to a step change in the load current and the output ripple voltage do not exceed the tolerance limits expected on the output voltage. During an output load transient, the output capacitor must supply all the additional current demanded by the load until the SP7651 adjusts the inductor current to the new value. FS = Switching Frequency D = Duty Cycle COUT = Output Capacitance Value Input Capacitor Selection The input capacitor should be selected for ripple current rating, capacitance and voltage rating. The input capacitor must meet the ripple current requirement imposed by the switching current. In continuous conduction mode, the source current of the high-side MOSFET is approximately a square wave of duty cycle VOUT/VIN. Most of this current is supplied by the input bypass capacitors. The RMS value of input capacitor current is determined at the maximum output current and under the assumption that the peak In order to maintain VOUT, the capacitance must be large enough so that the output voltage is held up while the inductor current ramps up or down to the value corresponding to the new load current. Additionally, the ESR in the output capacitor causes a step in the output voltage equal to the current. Because of the fast transient response and inherent 100% and 0% duty cycle capability provided by the SP7651 when exposed to output load transient, the output capacitor is typically chosen for ESR, not for capacitance value. to peak inductor ripple current is low, it is given by: ICIN(rms) = IOUT(max) √D(1 - D) The worse case occurs when the duty cycle D is 50% and gives an RMS current value equal to IOUT/2. The output capacitor’s ESR, combined with the inductor ripple current, is typically the main contributor to output voltage ripple. The maximum allowable ESR required to maintain a specified output voltage ripple can be calculated by: RESR Select input capacitors with adequate ripple current rating to ensure reliable operation. The power dissipated in the input capacitor is: 2 PCIN = ICIN ( rms ) R ESR ( CIN ) ≤ ∆VOUT IPK-PK This can become a significant part of power losses in a converter and hurt the overall energy transfer efficiency. The input voltage ripple primarily depends on the input capacitor ESR and capacitance. Ignoring the inductor ripple current, the input voltage ripple can be determined by: where: ∆VOUT = Peak to Peak Output Voltage Ripple IPK-PK = Peak to Peak Inductor Ripple Current The total output ripple is a combination of the ESR and the output capacitance value and can be calculated as follows: ( ∆VOUT = IPP (1 – D) COUTFS Date: 08/25/04 ) 2 + (IPPRESR)2 SP7651 Wide Input Voltage Range 3A, 900kHz, Buck Regulator 8 © Copyright 2004 Sipex Corporation APPLICATIONS INFORMATION ∆ VIN = I out (max) RE SR (CIN ) + High cross over frequency is desirable for fast transient response, but often jeopardizes the system stability. Cross over frequency should be higher than the ESR zero but less than 1/5 of the switching frequency. The ESR zero is contributed by the ESR associated with the output capacitors and can be determined by: I OUT ( MAX )VOUT (VI N − VOUT ) FS C INV IN 2 The capacitor type suitable for the output capacitors can also be used for the input capacitors. However, exercise extra caution when tantalum capacitors are used. Tantalum capacitors are known for catastrophic failure when exposed to surge current, and input capacitors are prone to such surge current when power supplies are connected “live” to low impedance power sources. 1 ƒZ(ESR) = 2π COUT RESR Loop Compensation Design The next step is to calculate the complex conjugate poles contributed by the LC output filter, The open loop gain of the whole system can be divided into the gain of the error amplifier, PWM modulator, buck converter output stage, and feedback resistor divider. In order to cross over at the selected frequency FCO, the gain of the error amplifier has to compensate for the attenuation caused by the rest of the loop at this frequency. 2π Type III Voltage Loop Compensation GAMP (s) Gain Block + _ L COUT When the output capacitors are of a Ceramic Type, the SP7651 Evaluation Board requires a Type III compensation circuit to give a phase boost of 180° in order to counteract the effects of an under damped resonance of the output filter at the double pole frequency. The goal of loop compensation is to manipulate loop frequency response such that its gain crossesover 0db at a slope of -20db/dec. The first step of compensation design is to pick the loop cross over frequency. VREF (Volts) 1 ƒP(LC) = PWM Stage GPWM Gain Block Output Stage GOUT (s) Gain Block VIN (SRz2Cz2+1)(SR1Cz3+1) (SRESRCOUT+ 1) VRAMP_PP SR1Cz2(SRz3Cz3+1)(SRz2Cp1+1) [S^2LCOUT+S(RESR+RDC) COUT+1] VOUT (Volts) Notes: RESR = Output Capacitor Equivalent Series Resistance. RDC = Output Inductor DC Resistance. VRAMP_PP = SP6132 Internal RAMP Amplitude Peak to Peak Voltage. Condition: Cz2 >> Cp1 & R1 >> Rz3 Output Load Resistance >> RESR & RDC Voltage Feedback GFBK Gain Block R2 VFBK (Volts) (R1 + R2) or VREF VOUT SP7651 Voltage Mode Control Loop with Loop Dynamic Definitions: RESR = Output Capacitor Equivalent Series Resistance RDC = Output Inductor DC Resistance RRAMP_PP = SP7651 internal RAMP Amplitude Peak to Peak Voltage Conditions: CZ 2 >> Cp1 and R1 >> RZ 3 Output Load Resistance >> RESR and RDC Date: 08/25/04 SP7651 Wide Input Voltage Range 3A, 900kHz, Buck Regulator 9 © Copyright 2004 Sipex Corporation APPLICATIONS INFORMATION Gain (dB) Error Amplifier Gain Bandwidth Product Condition: C22 >> CP1, R1 >> RZ3 1/6.28 (RZ3) (CZ3) 1/6.28 (RZ2) (CP1) 1/6.28 (R1) (CZ2) 1/6.28 (R1) (CZ3) 1/6.28(R22) (CZ2) 20 Log (RZ2/R1) Frequency (Hz) Bode Plot of Type III Error Amplifier Compensation. CP1 RZ3 CZ3 CZ2 RZ2 VOUT R1 68.1k, 1% 5 VFB R SET + + - 0.8V R SET 6 COMP CF1 =54.48/ (VOUT -0.8) (kΩ) Type III Error Amplifier Compensation Circuit Date: 08/25/04 SP7651 Wide Input Voltage Range 3A, 900kHz, Buck Regulator 10 © Copyright 2004 Sipex Corporation PACKAGE: 26 PIN DFN D (7 x 4 mm) E Top View A A3 A1 Side View b e L E2 D2 D2 D3 26 Pin DFN SYMBOL A A1 A3 b D D2 D3 e E E2 L Bottom View DIMENSIONS in (mm) MIN NOM MAX 0.800 0.850 0.900 0.000 - 0.050 0.178 0.203 0.228 0.17 0.22 0.27 6.95 7.05 7.00 2.05 2.10 1.78 1.83 1.88 2.00 0.45 0.50 0.55 3.95 4.00 4.05 2.730 2.780 2.830 0.350 0.400 0.450 26 Pin DFN Date: 08/25/04 SP7651 Wide Input Voltage Range 3A, 900kHz, Buck Regulator 11 © Copyright 2004 Sipex Corporation ORDERING INFORMATION Part Number Temperature Package SP7651ER/TR ......................................... -40°C to +85°C ................................. 26 Pin 7 X 4 DFN SP7651ER-L/TR ..................................... -40°C to +85°C ............. (Lead Free) 26 Pin 7 X 4 DFN /TR = Tape and Reel Pack quantity is 3000 DFN. Corporation ANALOG EXCELLENCE Sipex Corporation Headquarters and Sales Office 233 South Hillview Drive Milpitas, CA 95035 TEL: (408) 934-7500 FAX: (408) 935-7600 Sipex Corporation reserves the right to make changes to any products described herein. Sipex does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others. Date: 08/25/04 SP7651 Wide Input Voltage Range 3A, 900kHz, Buck Regulator 12 © Copyright 2004 Sipex Corporation