SITRONIX ST7066U

ST
Sitronix
ST7066U
Dot Matrix LCD Controller/Driver
n Features
l
l
l
l
l
l
l
l
5 x 8 and 5 x 11 dot matrix possible
Low power operation support:
-- 2.7 to 5.5V
Wide range of LCD driver power
-- 3.0 to 10V
Correspond to high speed MPU bus
interface
-- 2 MHz (when VCC = 5V)
4-bit or 8-bit MPU interface enabled
80 x 8-bit display RAM (80 characters max.)
13,200-bit character generator ROM for a
total of 240 character fonts(5 x 8 dot or 5 x 11
dot)
64 x 8-bit character generator RAM
-- 8 character fonts (5 x 8 dot)
-- 4 character fonts (5 x 11 dot)
l
l
l
l
l
l
l
16-common x 40-segment liquid crystal
display driver
Programmable duty cycles
-- 1/8 for one line of 5 x 8 dots with cursor
-- 1/11 for one line of 5 x 11 dots & cursor
-- 1/16 for two lines of 5 x 8 dots & cursor
Wide range of instruction functions:
Display clear, cursor home, display on/off,
cursor on/off, display character blink, cursor
shift, display shift
Automatic reset circuit that initializes the
controller/driver after power on
Internal oscillator with external resistors
Low power consumption
QFP80 and Bare Chip available
n Description
The ST7066U dot-matrix liquid crystal display
controller and driver LSI displays alphanumeric,
Japanese kana characters, and symbols. It can be
configured to drive a dot-matrix liquid crystal display
under the control of a 4- or 8-bit microprocessor.
Since all the functions such as display RAM,
character generator, and liquid crystal driver, required
for driving a dot-matrix liquid crystal display are
internally provided on one chip, a minimal system can
be interfaced with this controller/driver.
The ST7066U character generator ROM is extended
to generate 240 5x8(5x11) dot character fonts for a
V2.2
total of 240 different character fonts. The low power
supply (2.7V to 5.5V) of the ST7066U is suitable for
any portable battery-driven product requiring low
power dissipation.
The ST7066U LCD driver consists of 16 common
signal drivers and 40 segment signal drivers which
can extend display size by cascading segment driver
ST7065 or ST7063. The maximum display size can
be either 80 characters in 1-line display or 40
characters in 2-line display. A single ST7066U can
display up to one 8-character line or two 8-character
lines.
Product Name
Support Character
ST7066U-0A
English / Japan
ST7066U-0B
ST7066U-0E
English / European
English / European
1/42
2006/05/11
ST7066U
ST7066 Serial Specification Revision History
Version
V2.2
Date
Description
1.7
1. Added 8051 Example Program Code(Page 21,23)
2. Added Annotated Flow Chart :
2000/10/31
“BF cannot be checked before this instruction”
3. Changed Maximum Ratings
Power Supply Voltage:+5.5V →+7.0V(Page 28)
1.8
2000/11/14 Added QFP Pad Configuration(Page 5)
1.8a
1. Moved QFP Package Dimensions(Page 39) to
Page 5
2000/11/30
2. Changed DC Characteristics Ratings(Page
32,33)
2.0
2001/03/01 Transition to ST7066U
2.1
2006/04/10
2.2
2006/05/11 Emphasis checking BF procedure (Page 9, 27, 28).
1.
2.
Add Power Supply Conditions (Page 31);
Modify reset description on Page 22.
2/42
2006/05/11
ST7066U
n Block Diagram
OSC1 OSC2
Reset
circuit
CL1
CL2
M
Timing
generator
CPG
Instruction
register(IR)
D
Instruction
decoder
RS
RW
E
Display data
RAM
(DDRAM)
80x8 bits
16-bit
shift
register
Common
signal
driver
40-bit
latch
circuit
Segment
signal
driver
MPU
interface
Address
counter
40-bit
shift
register
SEG1 to
SEG40
Data
register
(DR)
DB4 to
DB7
DB0 to
DB3
COM1 to
COM16
Input/
output
buffer
LCD drive
voltage
selector
Busy
flag
Character
generator
RAM
(CGRAM)
64 bytes
Character
generator
ROM
(CGROM)
13,200 bits
Cursor
and
blink
controller
GND
Parallel/serial converter
and
attribute circuit
Vcc
V1
V2.2
V2
V3
V4
3/42
V5
2006/05/11
ST7066U
SEG26
SEG27
SEG28
SEG29
SEG30
SEG31
SEG32
SEG33
SEG34
SEG35
SEG36
SEG37
SEG38
77
76
75
74
73
72
71
70
69
68
67
66
65
64
SEG39
63
SEG40
62
COM16
4
61
COM15
SEG18
5
60
COM14
SEG17
6
59
COM13
SEG16
7
58
COM12
SEG15
8
57
COM11
SEG14
9
56
COM10
SEG13
10
55
COM09
SEG12
11
54
COM08
SEG11
12
53
COM07
SEG10
13
52
COM06
SEG09
14
51
COM05
SEG08
15
50
COM04
SEG07
16
49
COM03
SEG06
17
48
COM02
SEG05
18
47
COM01
SEG04
19
46
DB7
SEG03
20
45
DB6
SEG02
21
44
DB5
SEG01
22
43
DB4
GND
23
42
DB3
OSC1
24
41
DB2
ST7066U
(0,0)
CL1
CL2
33
3
35
36
37
38
39
40
DB1
32
DB0
31
E
30
R/W
29
RS
28
D
27
M
26
Vcc
25
V5
Chip Size : 2300x3000μm
Coordinate : Pad Center
Origin : Chip Center
Min Pad Pitch : 120μm
Pad Size : 96x96μm
V4
SEG19
78
V3
3
SEG25
SEG20
79
V2
2
SEG24
SEG21
80
V1
1
OSC2
SEG22
SEG23
n Pad Arrangement
Substrate Connect to VDD.
V2.2
4/42
2006/05/11
ST7066U
n Package Dimensions
V2.2
5/42
2006/05/11
ST7066U
n Pad Configuration(80 QFP)
V2.2
S22
1
S21
S
2
3
S
2
4
S
2
5
S
2
6
S
2
7
S
2
8
S
2
9
S
3
0
S
3
1
S
3
2
S
3
3
S
3
4
S
3
5
S
3
6
S
3
7
S
3
8
8
0
7
9
7
8
7
7
7
6
7
5
7
4
7
3
7
2
7
1
7
0
6
9
6
8
6
7
6
6
6
5
64
S39
2
63
S40
S20
3
62
C16
S19
4
61
C15
S18
5
60
C14
S17
6
59
C13
S16
7
58
C12
S15
8
57
C11
S14
9
56
C10
S13
10
55
C09
S12
11
54
C08
S11
12
53
C07
S10
13
52
C06
S09
14
51
C05
S08
15
50
C04
S07
16
49
C03
S06
17
48
C02
S05
18
47
C01
S04
19
46
DB7
S03
20
45
DB6
S02
21
44
DB5
S01
22
43
DB4
GND
23
42
DB3
OSC1
24
41
DB2
2
5
2
6
2
7
2
8
2
9
3
0
3
1
3
2
3
3
3
4
3
5
3
6
3
7
3
8
3
9
4
0
O
S
C
2
V
1
V
2
V
3
V
4
V
5
C
L
1
C
L
2
V
C
C
M D
R
S
R E
W
D
B
0
D
B
1
6/42
2006/05/11
ST7066U
n Pad Location
Pad No. Function
V2.2
Coordinates
X
Y
Pad No. Function
X
Y
DB2
1040
-1400
1
SEG22
-1040
1400
41
2
SEG21
-1040
1270
42
DB3
1040
-1270
3
SEG20
-1040
1140
43
DB4
1040
-1140
4
SEG19
-1040
1020
44
DB5
1040
-1020
5
SEG18
-1040
900
45
DB6
1040
-900
6
SEG17
-1040
780
46
DB7
1040
-780
7
SEG16
-1040
660
47
COM1
1040
-660
8
SEG15
-1040
540
48
COM2
1040
-540
9
SEG14
-1040
420
49
COM3
1040
-420
10
SEG13
-1040
300
50
COM4
1040
-300
11
SEG12
-1040
180
51
COM5
1040
-180
12
SEG11
-1040
60
52
COM6
1040
-60
13
SEG10
-1040
-60
53
COM7
1040
60
14
SEG9
-1040
-180
54
COM8
1040
180
15
SEG8
-1040
-300
55
COM9
1040
300
16
SEG7
-1040
-420
56
COM10
1040
420
17
SEG6
-1040
-540
57
COM11
1040
540
18
SEG5
-1040
-660
58
COM12
1040
660
19
SEG4
-1040
-780
59
COM13
1040
780
20
SEG3
-1040
-900
60
COM14
1040
900
21
SEG2
-1040
-1020
61
COM15
1040
1020
22
SEG1
-1040
-1140
62
COM16
1040
1140
23
GND
-1040
-1270
63
SEG40
1040
1270
24
OSC1
-1040
-1400
64
SEG39
1040
1400
25
OSC2
-910
-1400
65
SEG38
910
1400
26
V1
-780
-1400
66
SEG37
780
1400
27
V2
-660
-1400
67
SEG36
660
1400
28
V3
-540
-1400
68
SEG35
540
1400
29
V4
-420
-1400
69
SEG34
420
1400
30
V5
-300
-1400
70
SEG33
300
1400
31
CL1
-180
-1400
71
SEG32
180
1400
32
CL2
-60
-1400
72
SEG31
60
1400
33
Vcc
60
-1400
73
SEG30
-60
1400
34
M
180
-1400
74
SEG29
-180
1400
35
D
300
-1400
75
SEG28
-300
1400
36
RS
420
-1400
76
SEG27
-420
1400
37
RW
540
-1400
77
SEG26
-540
1400
38
E
660
-1400
78
SEG25
-660
1400
39
DB0
780
-1400
79
SEG24
-780
1400
40
DB1
910
-1400
80
SEG23
-910
1400
7/42
2006/05/11
ST7066U
n Pin Function
Name
Number
I/O Interfaced with
RS
1
I
MPU
R/W
1
I
MPU
E
1
I
MPU
DB4 to DB7
4
I/O
MPU
DB0 to DB3
4
I/O
MPU
CL1
1
O
Extension driver
CL2
1
O
Extension driver
M
1
O
Extension driver
D
1
O
Extension driver
COM1 to
COM16
16
O
LCD
SEG1 to
SEG40
40
O
LCD
V1 to V5
5
-
Power supply
VCC , GND
2
-
Power supply
OSC1, OSC2
2
Oscillation
resistor clock
Function
Select registers.
0: Instruction register (for write) Busy flag:
address counter (for read)
1: Data register (for write and read)
Select read or write.
0: Write
1: Read
Starts data read/write.
Four high order bi-directional tristate data bus
pins. Used for data transfer and receive
between the MPU and the ST7066U. DB7 can
be used as a busy flag.
Four low order bi-directional tristate data bus
pins. Used for data transfer and receive
between the MPU and the ST7066U.
These pins are not used during 4-bit operation.
Clock to latch serial data D sent to the
extension driver
Clock to shift serial data D
Switch signal for converting the liquid crystal
drive waveform to AC
Character pattern data corresponding to each
segment signal
Common signals that are not used are changed
to non-selection waveform. COM9 to COM16
are non-selection waveforms at 1/8 duty factor
and COM12 to COM16 are non-selection
waveforms at 1/11 duty factor.
Segment signals
Power supply for LCD drive
VCC - V5 = 10 V (Max)
VCC : 2.7V to 5.5V, GND: 0V
When crystal oscillation is performed, a resistor
must be connected externally. When the pin
input is an external clock, it must be input to OSC1.
Note:
1. Vcc>=V1>=V2>=V3>=V4>=V5 must be maintained
2. Two clock options:
R=91KΩ (Vcc=5V)
R=75KΩ (Vcc=3V)
OSC1
OSC2
R
V2.2
OSC1
OSC2
Clock input
8/42
2006/05/11
ST7066U
n Function Description
l System Interface
This chip has all two kinds of interface type with MPU : 4-bit bus and 8-bit bus. 4-bit bus or 8-bit bus is selected
by DL bit in the instruction register.
During read or write operation, two 8-bit registers are used. One is data register (DR), the other is instruction
register(IR).
The data register(DR) is used as temporary data storage place for being written into or read from
DDRAM/CGRAM, target RAM is selected by RAM address setting instruction. Each internal operation, reading
from or writing into RAM, is done automatically. So to speak, after MPU reads DR data, the data in the next
DDRAM/CGRAM address is transferred into DR automatically. Also after MPU writes data to DR, the data in DR
is transferred into DDRAM/CGRAM automatically.
The Instruction register(IR) is used only to store instruction code transferred from MPU. MPU cannot use it to
read instruction data.
To select register, use RS input pin in 4-bit/8-bit bus mode.
RS R/W
L
L
L
H
H
H
L
H
Operation
Instruction Write operation (MPU writes Instruction code
into IR)
Read Busy Flag(DB7) and address counter (DB0 ~ DB6)
Data Write operation (MPU writes data into DR)
Data Read operation (MPU reads data from DR)
Table 1. Various kinds of operations according to RS and R/W bits.
l Busy Flag (BF)
When BF = "High”, it indicates that the internal operation is being processed. So during this time the next
instruction cannot be accepted. BF can be read, when RS = Low and R/W = High (Read Instruction Operation),
through DB7 port. Before executing the next instruction, be sure that BF is not High. Before checking BF, be
sure to wait at least 80us. Please refer to Page 27 for the example. Do NOT keep “E” always “High” for
checking BF.
l Address Counter (AC)
Address Counter(AC) stores DDRAM/CGRAM address, transferred from IR.
After writing into (reading from) DDRAM/CGRAM, AC is automatically increased (decreased) by 1.
When RS = "Low" and R/W = "High", AC can be read through DB0 ~ DB6 ports.
V2.2
9/42
2006/05/11
ST7066U
Display Data RAM (DDRAM)
l
Display data RAM (DDRAM) stores display data represented in 8-bit character codes. Its extended capacity is 80
x 8 bits, or 80 characters. The area in display data RAM (DDRAM) that is not used for display can be used as
general data RAM. See Figure 1 for the relationships between DDRAM addresses and positions on the liquid
crystal display.
The DDRAM address (ADD ) is set in the address counter (AC) as hexadecimal.
1-line display (N = 0) (Figure 2)
Ø
When there are fewer than 80 display characters, the display begins at the head position. For
example, if using only the ST7066U, 8 characters are displayed. See Figure 3.
When the display shift operation is performed, the DDRAM address shifts. See Figure 3.
High Order
bits
Low Order
bits
Example: DDRAM Address 4F
AC AC6 AC5 AC4 AC3 AC2 AC1 AC0
1
0
0
1
1
1
78
79
80
4D 4E
4F
1
Figure 1 DDRAM Address
Display
Position
1
(Digit)
00
DDRAM Address
2
3
4
5
6
01
02
03
04
05
………………..
Figure 2 1-Line Display
Display
Position
1
2
3
4
5
6
7
8
00
01
02
03
04
05
06
07
For
Shift Left
01
02
03
04
05
06
07
08
For
Shift Right
4F
00
01
02
03
04
05
06
DDRAM
Address
Figure 3 1-Line by 8-Character Display Example
2-line display (N = 1) (Figure 4)
Ø
Case 1: When the number of display characters is less than 40 ´ 2 lines, the two lines are displayed from the head. Note
that the first line end address and the second line start address are not consecutive. For example, when just the
ST7066U is used, 8 characters ´ 2 lines are displayed. See Figure 5.
V2.2
10/42
2006/05/11
ST7066U
When display shift operation is performed, the DDRAM address shifts. See Figure 5.
Display
Position
1
00
DDRAM
Address
40
(hexadecimal)
2
3
4
5
6
01
02
03
04
05
41
42
43
44
45
38
39
40
………………..
25
26
27
………………..
65
66
67
Figure 4 2-Line Display
Display
Position
DDRAM
Address
For
Shift Left
For
Shift Right
1
2
3
4
5
6
7
8
00
01
02
03
04
05
06
07
40
41
42
43
44
45
46
47
01
02
03
04
05
06
07
08
41
42
43
44
45
46
47
48
27
00
01
02
03
04
05
06
67
40
41
42
43
44
45
46
Figure 5 2-Line by 8-Character Display Example
Case 2: For a 16-character ´ 2-line display, the ST7066U can be extended using one 40-output
extension driver. See Figure 6.
When display shift operation is performed, the DDRAM address shifts. See Figure 6.
Display
1
Position
00
DDRAM
Address
40
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
01
02
03
04
05
06
07
08
09
0A
0B 0C 0D 0E
0F
41
42
43
44
45
46
47
48
49
4A
4B 4C 4D 4E
4F
For
Shift
Left
01
02
03
04
05
06
07
08
09
0A
0B 0C 0D 0E
0F
10
41
42
43
44
45
46
47
48
49
4A
4B 4C 4D 4E
4F
50
For
Shift
Right
27
00
01
02
03
04
05
06
07
08
09
0A
0B 0C 0D 0E
67
40
41
42
43
44
45
46
47
48
49
4A
4B 4C 4D 4E
Figure 6 2-Line by 16-Character Display Example
V2.2
11/42
2006/05/11
ST7066U
l Character Generator ROM (CGROM)
The character generator ROM generates 5 x 8 dot or 5 x 11 dot character patterns from 8-bit character codes. It
can generate 240 5 x 8 dot character patterns. User-defined character patterns are also available by
mask-programmed ROM.
l Character Generator RAM (CGRAM)
In the character generator RAM, the user can rewrite character patterns by program. For 5 x 8 dots, eight
character patterns can be written, and for 5 x 11 dots, four character patterns can be written.
Write into DDRAM the character codes at the addresses shown as the left column of Table 4 to show the
character patterns stored in CGRAM.
See Table 5 for the relationship between CGRAM addresses and data and display patterns. Areas that are not
used for display can be used as general data RAM.
l Timing Generation Circuit
The timing generation circuit generates timing signals for the operation of internal circuits such as
DDRAM, CGROM and CGRAM. RAM read timing for display and internal operation timing by MPU
access are generated separately to avoid interfering with each other. Therefore, when writing data to
DDRAM, for example, there will be no undesirable interference, such as flickering, in areas other than
the display area.
l LCD Driver Circuit
LCD Driver circuit has 16 common and 40 segment signals for LCD driving. Data from CGRAM/CGROM is
transferred to 40 bit segment latch serially, and then it is stored to 40 bit shift latch. When each common is
selected by 16 bit common register, segment data also output through segment driver from 40 bit segment latch.
In case of 1-line display mode, COM1 ~ COM8 have 1/8 duty or COM1 ~ COM11 have 1/11duty , and in 2-line
mode, COM1 ~ COM16 have 1/16 duty ratio.
l Cursor/Blink Control Circuit
It can generate the cursor or blink in the cursor/blink control circuit. The cursor or the blink appears in the digit at
the display data RAM address set in the address counter.
V2.2
12/42
2006/05/11
ST7066U
Table 4 Correspondence between Character Codes and Character Patterns (ROM Code: 0A)
V2.2
13/42
2006/05/11
ST7066U
Table 4(Cont.) (ROM Code: 0B)
V2.2
14/42
2006/05/11
ST7066U
Table 4(Cont.) (ROM Code: 0E)
V2.2
15/42
2006/05/11
ST7066U
Character Code
(DDRAM Data)
b7 b6 b5 b4 b3 b2
0
0
0
0
0 0 0 0 0
0
0
0
0
0
0
0
0 0 0 0 0
0
0
0
b1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
CGRAM
Address
b0 b5 b4 b3 b2
0
0
0
0
0
0
0
0
0 0 0
0
1
0
1
0
1
0
1
1
0
1
0
1
0
1
0
0 0 1
1
1
1
1
1
1
1
1
b1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
Character Patterns
(CGRAM Data)
b0 b7 b6 b5 b4
0
1
1
0
0
0
1
0
- - 0
0
1
0
0
0
1
0
0
1
1
1
0
1
1
1
- - 0
1
1
1
0
1
1
0
b3
1
0
0
0
0
0
0
0
1
0
0
1
0
0
0
0
b2
1
1
1
1
1
1
1
0
1
0
0
1
1
0
0
0
b1
1
0
0
0
0
0
0
0
1
0
0
1
0
1
0
0
b0
1
0
0
0
0
0
0
0
0
1
1
0
0
0
1
0
Table 5 Relationship between CGRAM Addresses, Character Codes (DDRAM) and Character
patterns (CGRAM Data)
Notes:
1. Character code bits 0 to 2 correspond to CGRAM address bits 3 to 5 (3 bits: 8 types).
2. CGRAM address bits 0 to 2 designate the character pattern line position. The 8th line is the
cursor position and its display is formed by a logical OR with the cursor. Maintain the 8th line data, corresponding
to the cursor display position, at 0 as the cursor display. If the 8th line data is 1, 1 bits will light up the 8th line
regardless of the cursor presence.
3. Character pattern row positions correspond to CGRAM data bits 0 to 4 (bit 4 being at the left).
4. As shown Table 5, CGRAM character patterns are selected when character code bits 4 to 7 are
all 0. However, since character code bit 3 has no effect, the R display example above can be selected by either
character code 00H or 08H.
5. 1 for CGRAM data corresponds to display selection and 0 to non-selection.
“-“: Indicates no effect.
V2.2
16/42
2006/05/11
ST7066U
n Instructions
There are four categories of instructions that:
l Designate ST7066U functions, such as display format, data length, etc.
l Set internal RAM addresses
l Perform data transfer with internal RAM
l Others
Instruction Table:
Instruction
Clear
Display
Instruction Code
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
0
0
0
0
0
1
Return
Home
0
0
0
0
0
0
0
0
1
x
Entry Mode
Set
0
0
0
0
0
0
0
1
I/D
S
Display
ON/OFF
0
0
0
0
0
0
1
D
C
B
Cursor or
Display
Shift
0
0
0
0
0
1
S/C
R/L
x
Function
Set
0
0
0
0
1
DL
N
F
x
0
0
0
1
0
0
1
Read Busy
flag and
address
0
1
BF
Write data
to RAM
1
0
D7
Read data
from RAM
1
1
D7
Set CGRAM
address
Set DDRAM
address
Description
Description
Time
(270KHz)
Write "20H" to DDRAM. and
set DDRAM address to
"00H" from AC
Set DDRAM address to
"00H" from AC and return
cursor to its original position
if shifted. The contents of
DDRAM are not changed.
Sets cursor move direction
and specifies display shift.
These operations are
performed during data write
and read.
D=1:entire display on
C=1:cursor on
B=1:cursor position on
1.52 ms
1.52 ms
37 us
37 us
x
Set cursor moving and
display shift control bit, and
the direction, without
changing DDRAM data.
37 us
x
DL:interface data is 8/4 bits
N:number of line is 2/1
F:font size is 5x11/5x8
37 us
Set CGRAM address in
address counter
37 us
AC5 AC4 AC3 AC2 AC1 AC0
Set DDRAM address in
address counter
Whether during internal
operation or not can be
AC6 AC5 AC4 AC3 AC2 AC1 AC0 known by reading BF. The
contents of address counter
can also be read.
Write data into internal
D6
D5
D4
D3
D2
D1
D0 RAM
(DDRAM/CGRAM)
Read data from internal
D6
D5
D4
D3
D2
D1
D0 RAM
(DDRAM/CGRAM)
AC6 AC5 AC4 AC3 AC2 AC1 AC0
37 us
0 us
37 us
37 us
Note:
Be sure the ST7066U is not in the busy state (BF = 0) before sending an instruction from the MPU to the
ST7066U. If an instruction is sent without checking the busy flag, the time between the first instruction and next
instruction will take much longer than the instruction time itself. Refer to Instruction Table for the list of each
instruction execution time.
V2.2
17/42
2006/05/11
ST7066U
n Instruction Description
Clear Display
l
RS
Code
0
RW DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
0
0
0
0
1
Clear all the display data by writing "20H" (space code) to all DDRAM address, and set DDRAM address to
"00H" into AC (address counter). Return cursor to the original status, namely, bring the cursor to the left edge
on first line of the display. Make entry mode increment (I/D = "1").
Return Home
l
RS
Code
0
RW DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
0
0
0
1
x
Return Home is cursor return home instruction. Set DDRAM address to "00H" into the address counter.
Return cursor to its original site and return display to its original status, if shifted. Contents of DDRAM does
not change.
Entry Mode Set
l
RS
Code
0
RW DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
0
0
1
I/D
S
Set the moving direction of cursor and display.
Ø
I/D : Increment / decrement of DDRAM address (cursor or blink)
When I/D = "High", cursor/blink moves to right and DDRAM address is increased by 1.
When I/D = "Low", cursor/blink moves to left and DDRAM address is decreased by 1.
* CGRAM operates the same as DDRAM, when read from or write to CGRAM.
Ø
S: Shift of entire display
When DDRAM read (CGRAM read/write) operation or S = "Low", shift of entire display is not performed. If
S = "High" and DDRAM write operation, shift of entire display is performed according to I/D value (I/D =
"1" : shift left, I/D = "0" : shift right).
V2.2
S
I/D
Description
H
H
Shift the display to the left
H
L
Shift the display to the right
18/42
2006/05/11
ST7066U
Display ON/OFF
l
RS
Code
0
RW DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
0
1
D
C
B
Control display/cursor/blink ON/OFF 1 bit register.
D : Display ON/OFF control bit
When D = "High", entire display is turned on.
Ø
When D = "Low", display is turned off, but display data is remained in DDRAM.
C : Cursor ON/OFF control bit
When C = "High", cursor is turned on.
Ø
When C = "Low", cursor is disappeared in current display, but I/D register remains its data.
B : Cursor Blink ON/OFF control bit
When B = "High", cursor blink is on, that performs alternate between all the high data and display
Ø
character at the cursor position.
When B = "Low", blink is off.
Cursor or Display Shift
l
RS
Code
0
RW DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
1
S/C R/L
x
x
Without writing or reading of display data, shift right/left cursor position or display. This instruction is used to
correct or search display data. During 2-line mode display, cursor moves to the 2nd line after 40th digit of 1st
line. Note that display shift is performed simultaneously in all the line. When displayed data is shifted
repeatedly, each line shifted individually. When display shift is performed, the contents of address counter are
not changed.
l
S/C
R/L
Description
L
L
Shift cursor to the left
AC=AC-1
L
H
Shift cursor to the right
AC=AC+1
H
L
Shift display to the left. Cursor follows the display shift
AC=AC
H
H
Shift display to the right. Cursor follows the display shift AC=AC
Function Set
RS
Code
V2.2
AC Value
0
RW DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
1
DL
N
19/42
F
x
x
2006/05/11
ST7066U
DL : Interface data length control bit
When DL = "High", it means 8-bit bus mode with MPU.
Ø
When DL = "Low", it means 4-bit bus mode with MPU. So to speak, DL is a signal to select
8-bit or 4-bit bus mode.
When 4-bit bus mode, it needs to transfer 4-bit data by two times.
N : Display line number control bit
When N = "Low", it means 1-line display mode.
Ø
When N = "High", 2-line display mode is set.
F : Display font type control bit
When F = "Low", it means 5 x 8 dots format display mode
Ø
When F = "High", 5 x11 dots format display mode.
N
F
No. of Display Lines Character Font Duty Factor
L
L
1
5x8
1/8
L
H
1
5x11
1/11
H
x
2
5x8
1/16
Set CGRAM Address
l
Code
RS
RW
0
0
DB7
0
DB6
1
DB5
DB4
DB3
DB2
DB1
DB0
AC5 AC4 AC3 AC2 AC1 AC0
Set CGRAM address to AC.
This instruction makes CGRAM data available from MPU.
Set DDRAM Address
l
Code
RS
RW
0
0
DB7
1
DB6
DB5
DB4
DB3
DB2
DB1
DB0
AC6 AC5 AC4 AC3 AC2 AC1 AC0
Set DDRAM address to AC.
This instruction makes DDRAM data available from MPU.
When 1-line display mode (N = 0), DDRAM address is from "00H" to "4FH".
In 2-line display mode (N = 1), DDRAM address in the 1st line is from "00H" to "27H", and
DDRAM address in the 2nd line is from "40H" to "67H".
V2.2
20/42
2006/05/11
ST7066U
Read Busy Flag and Address
l
Code
RS
RW
DB7
0
1
BF
DB6
DB5
DB4
DB3
DB2
DB1
DB0
AC6 AC5 AC4 AC3 AC2 AC1 AC0
When BF = “High”, indicates that the internal operation is being processed.So during this time the next
instruction cannot be accepted.
The address Counter (AC) stores DDRAM/CGRAM addresses, transferred from IR.
After writing into (reading from) DDRAM/CGRAM, AC is automatically increased (decreased) by 1.
Write Data to CGRAM or DDRAM
l
RS
Code
1
RW DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
D7 D6 D5 D4 D3 D2 D1 D0
Write binary 8-bit data to DDRAM/CGRAM.
The selection of RAM from DDRAM, CGRAM, is set by the previous address set instruction
: DDRAM address set, CGRAM address set. RAM set instruction can also determine the AC
direction to RAM.
After write operation, the address is automatically increased/decreased by 1, according to
the entry mode.
Read Data from CGRAM or DDRAM
l
RS
Code
1
RW DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
1
D7 D6 D5 D4 D3 D2 D1 D0
Read binary 8-bit data from DDRAM/CGRAM.
The selection of RAM is set by the previous address set instruction. If address set instruction of RAM is not
performed before this instruction, the data that read first is invalid, because the direction of AC is not
determined. If you read RAM data several times without RAM address set instruction before read operation,
you can get correct RAM data from the second, but the first data would be incorrect, because there is no time
margin to transfer RAM data.
In case of DDRAM read operation, cursor shift instruction plays the same role as DDRAM address
set instruction : it also transfer RAM data to output data register. After read operation address counter is
automatically increased/decreased by 1 according to the entry mode. After CGRAM read operation, display
shift may not be executed correctly.
* In case of RAM write operation, after this AC is increased/decreased by 1 like read operation. In this time,
AC indicates the next address position, but you can read only the previous data by read instruction.
V2.2
21/42
2006/05/11
ST7066U
n Reset Function
Initializing by Internal Reset Circuit
An internal reset circuit automatically initializes the ST7066U when the power is turned on. The
following instructions are executed during the initialization. The busy flag (BF) is kept in the busy state
until the initialization ends (BF = 1). The busy state lasts for 40 ms after VCC rises to 4.5 V.
1. Display clear
2. Function set:
DL = 1; 8-bit interface data
N = 0; 1-line display
F = 0; 5x8 dot character font
3. Display on/off control:
D = 0; Display off
C = 0; Cursor off
B = 0; Blinking off
4. Entry mode set:
I/D = 1; Increment by 1
S = 0; No shift
Note:
If the electrical characteristics conditions listed in the table Power Supply Conditions (Page 31) are not met, the
internal reset circuit will not operate normally and will fail to initialize the ST7066U. For such a case, initialization
must be performed by the MPU as explain by the following figures.
V2.2
22/42
2006/05/11
ST7066U
n Initializing by Instruction
l
8-bit Interface (fosc=270KHz)
POWER ON
Wait time >40mS
After Vcc >4.5V
Function set
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
1
1
N
F
X
X
BF cannot be
checked before
this instruction.
Wait time >37uS
Function set
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
1
1
N
F
X
X
BF cannot be
checked before
this instruction.
Wait time >37uS
Display ON/OFF control
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
0
0
1
D
C
B
Wait time >37uS
Display clear
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
0
0
0
0
0
1
Wait time >1.52mS
Entry mode set
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
0
0
0
1
I/D
S
Initialization end
V2.2
23/42
2006/05/11
ST7066U
Ø
Initial Program Code Example For 8051 MPU(8 Bit Interface):
;--------------------------------------------------------------------------------INITIAL_START:
CALL DELAY40mS
MOV
CALL
CALL
A,#38H
;FUNCTION SET
WRINS_NOCHK ;8 bit,N=1,5*7dot
DELAY37uS
MOV
CALL
CALL
A,#38H
;FUNCTION SET
WRINS_NOCHK ;8 bit,N=1,5*7dot
DELAY37uS
MOV
CALL
CALL
A,#0FH
WRINS_CHK
DELAY37uS
;DISPLAY ON
MOV
CALL
CALL
A,#01H
WRINS_CHK
DELAY1.52mS
;CLEAR DISPLAY
MOV A,#06H
;ENTRY MODE SET
CALL WRINS_CHK
;CURSOR MOVES TO RIGHT
CALL DELAY37uS
;--------------------------------------------------------------------------------MAIN_START:
XXXX
XXXX
XXXX
XXXX
.
.
.
.
;--------------------------------------------------------------------------------WRINS_CHK:
CALL CHK_BUSY
WRINS_NOCHK:
CLR
RS
;EX:Port 3.0
CLR
RW
;EX:Port 3.1
SETB E
;EX:Port 3.2
MOV P1,A
;EX:Port 1=Data Bus
CLR
E
MOV P1,#FFH
;For Check Busy Flag
RET
;--------------------------------------------------------------------------------CHK_BUSY:
;Check Busy Flag
CLR
RS
SETB RW
SETB E
JB
P1.7,$
CLR
E
RET
V2.2
24/42
2006/05/11
ST7066U
l
4-bit Interface (fosc=270KHz)
POWER ON
Wait time >40mS
After Vcc >4.5V
Function set
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
1
1
X
X
X
X
BF cannot be
checked before
this instruction.
Wait time >37uS
Function set
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
1
0
X
X
X
X
0
0
N
F
X
X
X
X
X
X
BF cannot be
checked before
this instruction.
Wait time >37uS
Function set
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
1
0
X
X
X
X
0
0
N
F
X
X
X
X
X
X
BF cannot be
checked before
this instruction.
Wait time >37uS
Display ON/OFF control
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
0
0
X
X
X
X
0
0
1
D
C
B
X
X
X
X
Wait time >37uS
Display clear
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
0
0
X
X
X
X
0
0
0
0
0
1
X
X
X
X
Wait time >1.52mS
Entry mode set
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
0
0
X
X
X
X
0
0
0
1 I/D S
X
X
X
X
Initialization end
V2.2
25/42
2006/05/11
ST7066U
Ø
Initial Program Code Example For 8051 MPU(4 Bit Interface):
;------------------------------------------------------------------INITIAL_START:
CALL DELAY40mS
MOV
CALL
CALL
A,#38H
WRINS_ONCE
DELAY37uS
;FUNCTION SET
;8 bit,N=1,5*7dot
MOV
CALL
CALL
A,#28H
;FUNCTION SET
WRINS_NOCHK ;4 bit,N=1,5*7dot
DELAY37uS
MOV
CALL
CALL
A,#28H
;FUNCTION SET
WRINS_NOCHK ;4 bit,N=1,5*7dot
DELAY37uS
MOV
CALL
CALL
A,#0FH
WRINS_CHK
DELAY37uS
;DISPLAY ON
MOV
CALL
CALL
A,#01H
WRINS_CHK
DELAY1.52mS
;CLEAR DISPLAY
MOV A,#06H
;ENTRY MODE SET
CALL WRINS_CHK
CALL DELAY37uS
;------------------------------------------------------------------MAIN_START:
XXXX
XXXX
XXXX
XXXX
.
.
.
.
.
.
.
.
.
.
;------------------------------------------------------------------WRINS_CHK:
CALL CHK_BUSY
WRINS_NOCHK:
PUSH A
ANL A,#F0H
CLR RS
;EX:Port 3.0
CLR RW
;EX:Port 3.1
SETB E
;EX:Port 3.2
MOV P1,A
;EX:Port1=Data Bus
CLR E
POP A
SWAP A
WRINS_ONCE:
ANL A,#F0H
CLR RS
CLR RW
SETB E
MOV P1,A
CLR E
MOV P1,#FFH
;For Check Bus Flag
RET
;------------------------------------------------------------------CHK_BUSY:
;Check Busy Flag
PUSH A
MOV P1,#FFH
$1
CLR RS
SETB RW
SETB E
MOV A,P1
CLR E
MOV P1,#FFH
CLR RS
SETB RW
SETB E
NOP
CLR E
JB
A.7,$1
POP A
RET
.
.
V2.2
26/42
2006/05/11
ST7066U
n Interfacing to the MPU
The ST7066U can send data in either two 4-bit operations or one 8-bit operation, thus allowing interfacing with 4or 8-bit MPU.
l
For 4-bit interface data, only four bus lines (DB4 to DB7) are used for transfer. Bus lines DB0 to DB3
are disabled. The data transfer between the ST7066U and the MPU is completed after the 4-bit data has
been transferred twice. As for the order of data transfer, the four high order bits (for 8-bit operation, DB4 to
DB7) are transferred before the four low order bits (for 8-bit operation, DB0 to DB3). The busy flag must be
checked (one instruction) after the 4-bit data has been transferred twice. Two more 4-bit operations then
transfer the busy flag and address counter data.
Ø
Example of busy flag check timing sequence
RS
R /W
D e la y
(> 8 0 u s )
E
In te r n a l
o p e r a tio n
F u n c t io n in g
DB7
IR 7
IR 3
In s t r u c t io n w r it e
Ø
N ot
Busy
AC3
B u s y f la g c h e c k
AC3
B u s y f la g c h e c k
IR 3
I n s tr u c t io n w r it e
Intel 8051 interface
COM1 to COM16
P1.0 to P1.3
4
16
DB4 to DB7
P3.0
P3.1
P3.2
RS
R/W
E
Intel 8051 Serial
V2.2
IR 7
SEG1 to SEG40
40
ST7066U
27/42
2006/05/11
ST7066U
l
For 8-bit interface data, all eight bus lines (DB0 to DB7) are used.
Ø
Example of busy flag check timing sequence
RS
R /W
D e la y
(> 8 0 u s )
E
In te r n a l
o p e r a t io n
F u n c t io n in g
DB7
D a ta
I n s t r u c t io n w r ite
Ø
N ot
Busy
B usy
B usy
B u s y f la g c h e c k
B u s y f la g c h e c k
B u s y f la g c h e c k
I n s t r u c tio n w r it e
Intel 8051 interface
COM1 to COM16
P1.0 to P1.7
8
16
DB0 to DB7
RS
R/W
E
P3.0
P3.1
P3.2
Intel 8051 Serial
V2.2
D a ta
SEG1 to SEG40
40
ST7066U
28/42
2006/05/11
ST7066U
n Supply Voltage for LCD Drive
There are different voltages that supply to ST7066U’s pin (V1 - V5) to obtain LCD drive waveform. The relations
of the bias, duty factor and supply voltages are shown as below:
Duty Factor
1/8, 1/11
1/16
Bias
Supply Voltage
V1
V2
V3
V4
V5
1/4
Vcc - 1/4VLCD
Vcc - 1/2VLCD
Vcc - 1/2VLCD
Vcc - 3/4VLCD
Vcc - VLCD
1/5
Vcc - 1/5VLCD
Vcc - 2/5VLCD
Vcc - 3/5VLCD
Vcc - 4/5VLCD
Vcc- VLCD
VCC(+5V)
VCC(+5V)
VCC
VCC
R
R
V1
V2
V3
V1
R
V2
VLCD
V3
R
V4
R
V5
V5
VR
1/5 bias
(1/16 duty cycle)
-5V
V2.2
VLCD
R
V4
R
1/4 bias
(1/8, 1/11 duty cycle)
R
VR
-5V
29/42
2006/05/11
ST7066U
n Timing Characteristics
l
Writing data from MPU to ST7066U
VIH1
RS
VIL1
tAS
tAH
RW
tPW
tAH
tf
E
tDSW
tr
tH
Valid data
DB0-DB7
tC
l
Reading data from ST7066U to MPU
VIH1
RS
VIL1
tAS
tAH
RW
tPW
tAH
tf
E
tDDR
tH
tr
Valid data
DB0-DB7
tC
V2.2
30/42
2006/05/11
ST7066U
Interface Timing with External Driver
l
tct
VOH2
CL1
VOL2
tCWH
tCWH
CL2
tCST
tCWL
tct
D
tDH
tSU
M
tDM
n Power Supply Conditions
Symbol
Characteristics
tPOR
Power rise time
tIOL
I/O Low time
tPW
Enable pulse width
1.
Description
Power rise time that will trigger
internal power on reset circuit
The period that I/O is kept low.
Min.
Typ.
0.1
40
Max.
Unit
100
ms
ms
Please refer to the following tables.
During tPOR, VDD noise should be reduced (especially close to 2.0V). Otherwise the
Power-ON-Reset function might be triggered several times and maybe cause unexpected
result.
2.
V2.2
During tIOL, the I/O ports of the interface (control and data signals) should be kept at “Low”.
31/42
2006/05/11
ST7066U
n AC Characteristics
(TA = 25℃, VCC = 2.7V)
Symbol Characteristics
Test Condition
Min. Typ. Max.
Unit
Internal Clock Operation
fOSC
OSC Frequency
R = 75KW
190
270
350
KHz
External Clock Operation
fEX
TR,TF
External Frequency
-
125
270
410
KHz
Duty Cycle
-
45
50
55
%
Rise/Fall Time
-
-
-
0.2
ms
Write Mode (Writing data from MPU to ST7066U)
TC
Enable Cycle Time
Pin E
1200
-
-
ns
TPW
Enable Pulse Width Pin E
460
-
-
ns
TR,TF
Enable Rise/Fall Time Pin E
-
-
25
ns
0
-
-
ns
TAS
Address Setup Time Pins: RS,RW,E
TAH
Address Hold Time
Pins: RS,RW,E
10
-
-
ns
TDSW
Data Setup Time
Pins: DB0 - DB7
80
-
-
ns
TH
Data Hold Time
Pins: DB0 - DB7
10
-
-
ns
Read Mode (Reading Data from ST7066U to MPU)
TC
Enable Cycle Time
Pin E
1200
-
-
ns
TPW
Enable Pulse Width Pin E
480
-
-
ns
TR,TF
Enable Rise/Fall Time Pin E
-
-
25
ns
0
-
-
ns
TAS
Address Setup Time Pins: RS,RW,E
TAH
Address Hold Time
Pins: RS,RW,E
10
-
-
ns
TDDR
Data Setup Time
Pins: DB0 - DB7
-
-
320
ns
TH
Data Hold Time
Pins: DB0 - DB7
10
-
-
ns
Interface Mode with LCD Driver(ST7065)
V2.2
TCWH
Clock Pulse with High Pins: CL1, CL2
800
-
-
ns
TCWL
Clock Pulse with Low Pins: CL1, CL2
800
-
-
ns
TCST
Clock Setup Time
Pins: CL1, CL2
500
-
-
ns
TSU
Data Setup Time
Pin: D
300
-
-
ns
TDH
Data Hold Time
Pin: D
300
-
-
ns
TDM
M Delay Time
Pin: M
0
-
2000
ns
32/42
2006/05/11
ST7066U
n AC Characteristics
(TA = 25℃, VCC = 5V)
Symbol Characteristics
Test Condition
Min. Typ. Max.
Unit
Internal Clock Operation
fOSC
OSC Frequency
R = 91KW
190
270
350
KHz
External Clock Operation
fEX
TR,TF
External Frequency
-
125
270
410
KHz
Duty Cycle
-
45
50
55
%
Rise/Fall Time
-
-
-
0.2
ms
Write Mode (Writing data from MPU to ST7066U)
TC
Enable Cycle Time
Pin E
1200
-
-
ns
TPW
Enable Pulse Width Pin E
140
-
-
ns
TR,TF
Enable Rise/Fall Time Pin E
-
-
25
ns
0
-
-
ns
TAS
Address Setup Time Pins: RS,RW,E
TAH
Address Hold Time
Pins: RS,RW,E
10
-
-
ns
TDSW
Data Setup Time
Pins: DB0 - DB7
40
-
-
ns
TH
Data Hold Time
Pins: DB0 - DB7
10
-
-
ns
Read Mode (Reading Data from ST7066U to MPU)
TC
Enable Cycle Time
Pin E
1200
-
-
ns
TPW
Enable Pulse Width Pin E
140
-
-
ns
TR,TF
Enable Rise/Fall Time Pin E
-
-
25
ns
0
-
-
ns
TAS
Address Setup Time Pins: RS,RW,E
TAH
Address Hold Time
Pins: RS,RW,E
10
-
-
ns
TDDR
Data Setup Time
Pins: DB0 - DB7
-
-
100
ns
TH
Data Hold Time
Pins: DB0 - DB7
10
-
-
ns
Interface Mode with LCD Driver(ST7065)
V2.2
TCWH
Clock Pulse with High Pins: CL1, CL2
800
-
-
ns
TCWL
Clock Pulse with Low Pins: CL1, CL2
800
-
-
ns
TCST
Clock Setup Time
Pins: CL1, CL2
500
-
-
ns
TSU
Data Setup Time
Pin: D
300
-
-
ns
TDH
Data Hold Time
Pin: D
300
-
-
ns
TDM
M Delay Time
Pin: M
0
-
2000
ns
33/42
2006/05/11
ST7066U
n Absolute Maximum Ratings
Characteristics
Symbol
Value
Power Supply Voltage
VCC
-0.3 to +7.0
LCD Driver Voltage
VLCD
VCC-10.0 to VCC+0.3
Input Voltage
VIN
-0.3 to VCC+0.3
Operating Temperature
TA
-40 C to + 90 C
Storage Temperature
TSTO
-55 C to + 125 C
o
o
o
o
n DC Characteristics
( TA = 25℃ , VCC = 2.7 V – 4.5 V )
Symbol Characteristics
Test Condition
V2.2
Min. Typ. Max.
Unit
VCC
Operating Voltage
-
2.7
-
4.5
V
VLCD
LCD Voltage
VCC-V5
3.0
-
10.0
V
ICC
Power Supply Current
fOSC = 270KHz
VCC=3.0V
-
0.1
0.25
mA
VIH1
Input High Voltage
(Except OSC1)
-
0.7Vcc
-
VCC
V
VIL1
Input Low Voltage
(Except OSC1)
-
- 0.3
-
0.6
V
VIH2
Input High Voltage
(OSC1)
-
0.7Vcc
-
VCC
V
VIL2
Input Low Voltage
(OSC1)
-
-
-
0.2Vcc
V
VOH1
Output High Voltage
(DB0 - DB7)
IOH = -0.1mA
0.75
Vcc
-
-
V
VOL1
Output Low Voltage
(DB0 - DB7)
IOL = 0.1mA
-
-
0.2Vcc
V
VOH2
Output High Voltage
(Except DB0 - DB7)
IOH = -0.04mA
0.8VCC
-
VCC
V
VOL2
Output Low Voltage
(Except DB0 - DB7)
IOL = 0.04mA
-
-
0.2VCC
V
RCOM
Common Resistance
VLCD = 4V, Id = 0.05mA
-
2
20
KW
RSEG
Segment Resistance
VLCD = 4V, Id = 0.05mA
-
2
30
KW
ILEAK
Input Leakage
Current
VIN = 0V to VCC
-1
-
1
mA
IPUP
Pull Up MOS Current
VCC = 3V
-10
-50
-120
mA
34/42
2006/05/11
ST7066U
n DC Characteristics
( TA = 25℃, VCC = 4.5 V - 5.5 V )
Symbol Characteristics
V2.2
Test Condition
Min. Typ. Max.
Unit
VCC
Operating Voltage
-
4.5
-
5.5
V
VLCD
LCD Voltage
VCC-V5
3.0
-
10.0
V
ICC
Power Supply Current
fOSC = 270KHz
VCC=5.0V
-
0.2
0.5
mA
VIH1
Input High Voltage
(Except OSC1)
-
0.7Vcc
-
VCC
V
VIL1
Input Low Voltage
(Except OSC1)
-
-0.3
-
0.6
V
VIH2
Input High Voltage
(OSC1)
-
VCC-1
-
VCC
V
VIL2
Input Low Voltage
(OSC1)
-
-
-
1.0
V
VOH1
Output High Voltage
(DB0 - DB7)
IOH = -0.1mA
3.9
-
VCC
V
VOL1
Output Low Voltage
(DB0 - DB7)
IOL = 0.1mA
-
-
0.4
V
VOH2
Output High Voltage
(Except DB0 - DB7)
IOH = -0.04mA
0.9VCC
-
VCC
V
VOL2
Output Low Voltage
(Except DB0 - DB7)
IOL = 0.04mA
-
-
0.1VCC
V
RCOM
Common Resistance
VLCD = 4V, Id = 0.05mA
-
2
20
KW
RSEG
Segment Resistance
VLCD = 4V, Id = 0.05mA
-
2
30
KW
ILEAK
Input Leakage
Current
VIN = 0V to VCC
-1
-
1
mA
IPUP
Pull Up MOS Current
VCC = 5V
-50
-110
-180
mA
35/42
2006/05/11
ST7066U
n LCD Frame Frequency
l
Assume the oscillation frequency is 270KHZ, 1 clock cycle time = 3.7us, 1/16 duty; 1/5 bias,1 frame
= 3.7us x 200 x 16 = 11840us=11.8ms(84.7Hz)
200 clocks
1
2
3
4
16
1
2
3
4
16
1
2
3
4
16
Vcc
V1
V2
COM1
V3
V4
V5
Vcc
V1
V2
COM2
V3
V4
V5
Vcc
V1
V2
COM16
V3
V4
V5
Vcc
V1
V2
SEGx off
V3
V4
V5
Vcc
V1
V2
SEGx on
V3
V4
V5
1 frame
V2.2
36/42
2006/05/11
ST7066U
l
Assume the oscillation frequency is 270KHZ, 1 clock cycle time = 3.7us, 1/11 duty; 1/4 bias,1 frame
= 3.7us x 400 x 11 = 16280us=16.3ms (61.3Hz)
400 clocks
1
2
3
4
11
1
2
3
4
11
1
2
3
4
11
Vcc
V1
COM1
V2
V3
V4
V5
Vcc
V1
COM2
V2
V3
V4
V5
Vcc
V1
COM11
V2
V3
V4
V5
Vcc
V1
SEGx off
V2
V3
V4
V5
Vcc
V1
SEGx on
V2
V3
V4
V5
1 frame
V2.2
37/42
2006/05/11
ST7066U
l
Assume the oscillation frequency is 270KHZ, 1 clock cycle time = 3.7us, 1/8 duty; 1/4 bias,1 frame =
3.7us x 400 x 8 = 11840us=11.8ms (84.7Hz)
400 clocks
1
2
3
4
8
1
2
3
4
8
1
2
3
4
8
Vcc
V1
COM1
V2
V3
V4
V5
Vcc
V1
COM2
V2
V3
V4
V5
Vcc
V1
COM8
V2
V3
V4
V5
Vcc
V1
SEGx off
V2
V3
V4
V5
Vcc
V1
SEGx on
V2
V3
V4
V5
1 frame
V2.2
38/42
2006/05/11
ST7066U
n I/O Pad Configuration
VCC
VCC
VCC
PMOS
PMOS
PMOS
NMOS
NMOS
Input PAD:E(No Pull up)
Input PAD:RS,R/W(With Pull up)
VCC
PMOS
VCC
NMOS
Output PAD:CL1,CL2,M,D
VCC
VCC
VCC
Enable
PMOS
PMOS
PMOS
Data
NMOS
NMOS
I/O PAD:DB0-DB7
V2.2
39/42
2006/05/11
ST7066U
n LCD and ST7066U Connection
ST7066U
1. 5x8 dots, 8 characters x 1 line (1/4 bias, 1/8 duty)
COM1
.
.
.
.
.
.
.
.
COM8
SEG1
.
.
.
.
.
SEG40
LCD Panel: 8 Characters
x 1 line
ST7066U
2. 5x11 dots, 8 characters x 1 line (1/4 bias, 1/11 duty)
V2.2
COM1
.
.
.
.
.
.
.
.
.
.
.
COM11
LCD Panel: 8 Characters
x 1 line
SEG1
.
.
.
.
.
.
.
.
.
.
SEG40
40/42
2006/05/11
ST7066U
3. 5x8 dots, 8 characters x 2 line (1/5 bias, 1/16 duty)
ST7066U
COM1
.
.
.
.
.
.
.
.
COM8
COM9
.
.
.
.
.
.
.
.
COM16
SEG1
.
.
.
.
.
.
.
.
.
.
SEG40
LCD Panel: 8 Characters
x 2 line
4. 5x8 dots, 16 characters x 1 line (1/5 bias, 1/16 duty)
ST7066U
COM1
.
.
.
.
.
.
.
.
COM8
SEG1
.
.
.
.
.
.
SEG40
LCD Panel: 16
Characters x 1 line
COM9
.
.
.
.
.
.
.
.
COM16
V2.2
41/42
2006/05/11
ST7066U
n Application Circuit
Com 1-16
V5
V4
V3
V2
V1
M
CL1
CL2
GND
VCC
Seg 1-40
ST7066U
DB0-DB7
To MPU
Vcc(+5V)
Regsister
Dot Matrix LCD Panel
DL2
DR2
VDD
DL1
DL2
DR2
Seg 1-40
DL1
Seg 1-40
VDD
FCS
V3
V4
-V or GND
V6
M
CL2
CL1
DR1
DR1
FCS
V1
VR
ST7065
SHL1
ST7065
CL1
SHL1
V4
VEE
SHL2
V5
VSS
V2
CL2
V3
Regsister
V6
SHL2
V5
Regsister
M
V2
Regsister
VSS
VEE
V1
Regsister
VR=10K~30Kohm
Note:Regsister=2.2K~10K ohm
2006/05/11
42/42
V2.2