STK11C88 32K x 8 nvSRAM QuantumTrap™ CMOS Nonvolatile Static RAM FEATURES DESCRIPTION • 20ns, 25ns, 35ns and 45ns Access Times The Simtek STK11C88 is a fast static RAM with a nonvolatile, electrically erasable PROM element incorporated in each static memory cell. The SRAM can be read and written an unlimited number of times, while independent nonvolatile data resides in EEPROM. Data transfers from the SRAM to the EEPROM (the STORE operation), or from EEPROM to SRAM (the RECALL operation), take place using a software sequence. Transfers from the EEPROM to the SRAM (the RECALL operation) also take place automatically on restoration of power. • STORE to EEPROM Initiated by Software • RECALL to SRAM Initiated by Software or Power Restore • 10mA Typical ICC at 200ns Cycle Time • Unlimited READ, WRITE and RECALL Cycles • 1,000,000 STORE Cycles to EEPROM • 100-Year Data Retention in EEPROM • Commercial and Industrial Temperatures • 28-Pin PDIP and SOIC Packages The STK11C88 is pin-compatible with industrystandard SRAMs. BLOCK DIAGRAM PIN CONFIGURATIONS DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 STORE STATIC RAM ARRAY 512 x 512 RECALL STORE/ RECALL CONTROL SOFTWARE DETECT INPUT BUFFERS A5 A6 A7 A8 A9 A11 A12 A13 A14 ROW DECODER EEPROM ARRAY 512 x 512 COLUMN I/O 1 28 2 27 3 26 4 25 5 24 6 23 7 22 8 21 9 20 10 19 11 18 12 17 13 16 14 15 VCC W A13 A8 A9 A11 G A10 E DQ7 DQ6 DQ5 DQ4 DQ3 28 - 300 PDIP 28 - 600 PDIP 28 - 300 SOIC 28 - 350 SOIC PIN NAMES COLUMN DEC A0 A1 A2 A3 A4A10 G E W July 1999 A0 - A13 A14 A12 A7 A6 A5 A4 A3 A2 A1 A0 DQ0 DQ1 DQ2 VSS 5-1 A0 - A14 Address Inputs W Write Enable DQ0 - DQ7 Data In/Out E Chip Enable G Output Enable VCC Power (+5V) VSS Ground STK11C88 ABSOLUTE MAXIMUM RATINGSa Voltage on Input Relative to VSS . . . . . . . . . . –0.6V to (VCC + 0.5V) Voltage on DQ0-7 . . . . . . . . . . . . . . . . . . . . . . –0.5V to (VCC + 0.5V) Temperature under Bias . . . . . . . . . . . . . . . . . . . . . –55°C to 125°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1W DC Output Current (1 output at a time, 1s duration) . . . . . . . . 15mA Note a: Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. (VCC = 5.0V ± 10%)b DC CHARACTERISTICS SYMBOL ICC 1 ICC 2 ICC c Average VCC Current d c 3 MAX NOTES MAX 110 97 80 70 N/A 100 85 70 mA mA mA mA tAVAV = 20ns tAVAV = 25ns tAVAV = 35ns tAVAV = 45ns Average VCC Current during STORE 3 3 mA All Inputs Don’t Care, VCC = max Average VCC Current at tAVAV = 200ns 5V, 25°C, Typical 10 10 mA W ≥ (V CC – 0.2V) All Others Cycling, CMOS Levels 35 30 25 22 N/A 31 26 23 mA mA mA mA tAVAV = 20ns, E ≥ VIH tAVAV = 25ns, E ≥ VIH tAVAV = 35ns, E ≥ VIH tAVAV = 45ns, E ≥ VIH 750 750 µA E ≥ (V CC - 0.2V) All Others VIN ≤ 0.2V or ≥ (VCC – 0.2V) e Average VCC Current (Standby, Cycling TTL Input Levels) ISB e VCC Standby Current (Standby, Stable CMOS Input Levels) 2 INDUSTRIAL MIN UNITS ISB 1 COMMERCIAL MIN PARAMETER IILK Input Leakage Current ±1 ±1 µA VCC = max VIN = VSS to VCC IOLK Off-State Output Leakage Current ±5 ±5 µA VCC = max VIN = VSS to VCC, E or G ≥ VIH VIH Input Logic “1” Voltage 2.2 VCC + .5 2.2 VCC + .5 V All Inputs VSS – .5 0.8 VSS – .5 0.8 VIL Input Logic “0” Voltage VOH Output Logic “1” Voltage VOL Output Logic “0” Voltage TA Operating Temperature Note b: Note c: Note d: Note e: 2.4 0.4 0 V All Inputs V IOUT = – 4mA 0.4 V IOUT = 8mA 85 °C 2.4 70 –40 The STK11C88-20 requires VCC = 5.0V ± 5% supply to operate at specified speed. ICC and ICC are dependent on output loading and cycle rate. The specified values are obtained with outputs unloaded. 1 3 ICC is the average current required for the duration of the STORE cycle (tSTORE ) . 2 E ≥ VIH will not produce standby current levels until any nonvolatile cycle in progress has timed out. AC TEST CONDITIONS 5.0V Input Pulse Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to 3V Input Rise and Fall Times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ≤ 5ns Input and Output Timing Reference Levels . . . . . . . . . . . . . . . 1.5V Output Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Figure 1 CAPACITANCEf (TA = 25°C, f = 1.0MHz) 480 Ohms OUTPUT 255 Ohms SYMBOL PARAMETER MAX UNITS CONDITIONS CIN Input Capacitance 5 pF ∆V = 0 to 3V COUT Output Capacitance 7 pF ∆V = 0 to 3V Note f: 30 pF INCLUDING SCOPE AND FIXTURE These parameters are guaranteed but not tested. Figure 1: AC Output Loading July 1999 5-2 STK11C88 (VCC = 5.0V + 10%)b SRAM READ CYCLES #1 & #2 SYMBOLS NO. STK11C88-20 STK11C88-25 STK11C88-35 STK11C88-45 PARAMETER #1, #2 UNITS Alt. MIN MAX MIN MAX MIN MAX MIN MAX 1 tELQV tACS Chip Enable Access Time 2 tAVAVg tRC Read Cycle Time 3 tAVQVh tAA Address Access Time 22 25 35 45 ns 4 tGLQV tOE Output Enable to Data Valid 8 10 15 20 ns 5 tAXQXh tOH Output Hold after Address Change 5 6 tELQX tLZ Chip Enable to Output Active 5 7 tEHQZi tHZ Chip Disable to Output Inactive 8 tGLQX tOLZ Output Enable to Output Active 9 tGHQZi tOHZ Output Disable to Output Inactive 10 tELICCHf tPA Chip Enable to Power Active tPS Chip Disable to Power Standby 11 tEHICCL e, f 20 20 25 25 5 0 5 0 0 0 25 13 0 25 35 2 tAVAV ADDRESS 3 tAVQV tAXQX DATA VALID SRAM READ CYCLE #2: E Controlledg 2 tAVAV ADDRESS 1 11 tELQV tEHICCL 6 tELQX E 7 tEHQZ G 9 tGHQZ 4 8 tGLQV tGLQX DQ (DATA OUT) DATA VALID 10 tELICCH ICC July 1999 ACTIVE STANDBY 5-3 15 ns ns ns 45 SRAM READ CYCLE #1: Address Controlledg, h DQ (DATA OUT) ns 0 Note g: W must be high during SRAM READ cycles and low during SRAM WRITE cycles. Note h: I/O state assumes E, G < VIL and W > VIH; device is continuously selected. Note i: Measured ± 200mV from steady state output voltage. 5 ns 15 0 10 0 ns 5 13 ns ns 5 10 7 45 45 5 5 7 35 35 ns STK11C88 (VCC = 5.0V + 10%)b SRAM WRITE CYCLES #1 & #2 SYMBOLS STK11C88-20 NO. STK11C88-25 STK11C88-35 STK11C88-45 PARAMETER UNITS #1 #2 Alt. MIN MAX MIN MAX MIN MAX MIN MAX 12 tAVAV tAVAV tWC Write Cycle Time 20 25 35 45 ns 13 tWLWH tWLEH tWP Write Pulse Width 15 20 25 30 ns 14 tELWH tELEH tCW Chip Enable to End of Write 15 20 25 30 ns 15 tDVWH tDVEH tDW Data Set-up to End of Write 8 10 12 15 ns 16 tWHDX tEHDX tDH Data Hold after End of Write 0 0 0 0 ns 17 tAVWH tAVEH tAW Address Set-up to End of Write 15 20 25 30 ns 18 tAVWL tAVEL tAS Address Set-up to Start of Write 0 0 0 0 ns 19 tWHAX tEHAX tWR Address Hold after End of Write 0 0 0 0 ns 20 tWLQZi, j tWZ Write Enable to Output Disable 21 tWHQX tOW Output Active after End of Write 7 10 5 5 13 5 5 Note j: If W is low when E goes low, the outputs remain in the high-impedance state. Note k: E or W must be ≥ VIH during address transitions. SRAM WRITE CYCLE #1: W Controlledk 12 tAVAV ADDRESS 19 tWHAX 14 tELWH E 17 tAVWH 18 tAVWL 13 tWLWH W 15 tDVWH DATA IN DATA OUT 16 tWHDX DATA VALID 20 tWLQZ HIGH IMPEDANCE PREVIOUS DATA 21 tWHQX SRAM WRITE CYCLE #2: E Controlledk 12 tAVAV ADDRESS 14 tELEH 18 tAVEL 19 tEHAX E 17 tAVEH 13 tWLEH W 15 tDVEH DATA IN DATA OUT July 1999 16 tEHDX DATA VALID HIGH IMPEDANCE 5-4 15 ns ns STK11C88 (VCC = 5.0V + 10%)b STORE INHIBIT/POWER-UP RECALL SYMBOLS STK11C88 NO. PARAMETER Standard 22 tRESTORE Power-up RECALL Duration 23 tSTORE STORE Cycle Duration 24 VSWITCH Low Voltage Trigger Level 25 VRESET Low Voltage Reset Level Note l: UNITS NOTES MIN 4.0 MAX 550 µs 10 ms 4.5 V 3.9 V tRESTORE starts from the time VCC rises above VSWITCH. STORE INHIBIT/POWER-UP RECALL VCC 5V 24 VSWITCH 25 VRESET STORE INHIBIT OWER-UP RECALL 22 tRESTORE DQ (DATA OUT) POWER-UP RECALL July 1999 BROWN OUT STORE INHIBIT BROWN OUT STORE INHIBIT BROWN OUT STORE INHIBIT NO RECALL (VCC DID NOT GO BELOW VRESET) NO RECALL (VCC DID NOT GO BELOW VRESET) RECALL WHEN VCC RETURNS ABOVE VSWITCH 5-5 l STK11C88 SOFTWARE STORE/RECALL MODE SELECTION E L L W A13 - A0 (hex) MODE I/O NOTES H 0E38 31C7 03E0 3C1F 303F 0FC0 Read SRAM Read SRAM Read SRAM Read SRAM Read SRAM Nonvolatile STORE Output Data Output Data Output Data Output Data Output Data Output High Z m, n H 0E38 31C7 03E0 3C1F 303F 0C63 Read SRAM Read SRAM Read SRAM Read SRAM Read SRAM Nonvolatile RECALL Output Data Output Data Output Data Output Data Output Data Output High Z m, n Note m: The six consecutive addresses must be in the order listed. W must be high during all six consecutive cycles to enable a nonvolatile cycle. Note n: While there are 15 addresses on the STK11C88, only the lower 14 are used to control software modes. (VCC = 5.0V ± 10%)b SOFTWARE STORE/RECALL CYCLEo, p NO. 26 SYMBOLS tAVAV 27 tAVEL 28 tELEHo 29 tELAXo 30 tRECALL o STK11C88-25 STK11C88-35 STK11C88-45 MIN MIN MIN MIN UNITS STORE/RECALL Initiation Cycle Time o STK11C88-20 PARAMETER MAX 20 MAX 25 MAX 35 MAX 45 ns Address Set-up Time 0 0 0 0 ns Clock Pulse Width 15 20 25 30 ns Address Hold Time 15 20 20 20 ns RECALL Duration 20 20 20 20 µs Note o: The software sequence is clocked with E controlled reads. Note p: The six consecutive addresses must be in the order listed in the Software STORE/RECALL Mode Selection Table: (0E38, 31C7, 03E0, 3C1F, 303F, 0FC0) for a STORE cycle or (0E38, 31C7, 03E0, 3C1F, 303F, 0C63) for a RECALL cycle. W must be high during all six consecutive cycles. SOFTWARE STORE/RECALL CYCLE: E Controlledp 26 26 tAVAV ADDRESS tAVAV ADDRESS #1 27 tAVEL ADDRESS #6 28 tELEH E 29 tELAX 23 tSTORE DQ (DATA July 1999 DATA VALID DATA VALID 5-6 30 / tRECALL HIGH IMPEDANCE STK11C88 DEVICE OPERATION SOFTWARE NONVOLATILE STORE The STK11C88 is a versatile memory chip that provides several modes of operation. The STK11C88 can operate as a standard 32K x 8 SRAM. It has a 32K x 8 EEPROM shadow to which the SRAM information can be copied or from which the SRAM can be updated in nonvolatile mode. The STK11C88 software STORE cycle is initiated by executing sequential READ cycles from six specific address locations. During the STORE cycle an erase of the previous nonvolatile data is first performed, followed by a program of the nonvolatile elements. The program operation copies the SRAM data into nonvolatile memory. Once a STORE cycle is initiated, further input and output are disabled until the cycle is completed. NOISE CONSIDERATIONS Note that the STK11C88 is a high-speed memory and so must have a high-frequency bypass capacitor of approximately 0.1µF connected between Vcc and Vss, using leads and traces that are as short as possible. As with all high-speed CMOS ICs, normal careful routing of power, ground and signals will help prevent noise problems. Because a sequence of READs from specific addresses is used for STORE initiation, it is important that no other READ or WRITE accesses intervene in the sequence or the sequence will be aborted and no STORE or RECALL will take place. SRAM READ To initiate the software STORE cycle, the following READ sequence must be performed: The STK11C88 performs a READ cycle whenever E and G are low and W is high. The address specified on pins A0-14 determines which of the 32,768 data bytes will be accessed. When the READ is initiated by an address transition, the outputs will be valid after a delay of tAVQV (READ cycle #1). If the READ is initiated by E or G, the outputs will be valid at tELQV or at tGLQV, whichever is later (READ cycle #2). The data outputs will repeatedly respond to address changes within the tAVQV access time without the need for transitions on any control input pins, and will remain valid until another address change or until E or G is brought high. 1. 2. 3. 4. 5. 6. 0E38 (hex) 31C7 (hex) 03E0 (hex) 3C1F (hex) 303F (hex) 0FC0 (hex) Valid READ Valid READ Valid READ Valid READ Valid READ Initiate STORE cycle The software sequence must be clocked with E controlled READs. Once the sixth address in the sequence has been entered, the STORE cycle will commence and the chip will be disabled. It is important that READ cycles and not WRITE cycles be used in the sequence, although it is not necessary that G be low for the sequence to be valid. After the tSTORE cycle time has been fulfilled, the SRAM will again be activated for READ and WRITE operation. SRAM WRITE A WRITE cycle is performed whenever E and W are low. The address inputs must be stable prior to entering the WRITE cycle and must remain stable until either E or W goes high at the end of the cycle. The data on the common I/O pins DQ0-7 will be written into the memory if it is valid tDVWH before the end of a W controlled WRITE or tDVEH before the end of an E controlled WRITE. SOFTWARE NONVOLATILE RECALL A software RECALL cycle is initiated with a sequence of READ operations in a manner similar to the software STORE initiation. To initiate the RECALL cycle, the following sequence of READ operations must be performed: It is recommended that G be kept high during the entire WRITE cycle to avoid data bus contention on the common I/O lines. If G is left low, internal circuitry will turn off the output buffers tWLQZ after W goes low. July 1999 Read address Read address Read address Read address Read address Read address 1. 2. 3. 4. 5. 6. 5-7 Read address Read address Read address Read address Read address Read address 0E38 (hex) 31C7 (hex) 03E0 (hex) 3C1F (hex) 303F (hex) 0C63 (hex) Valid READ Valid READ Valid READ Valid READ Valid READ Initiate RECALL cycle STK11C88 Internally, RECALL is a two-step procedure. First, the SRAM data is cleared, and second, the nonvolatile information is transferred into the SRAM cells. After the tRECALL cycle time the SRAM will once again be ready for READ and WRITE operations. The RECALL operation in no way alters the data in the EEPROM cells. The nonvolatile data can be recalled an unlimited number of times. HARDWARE PROTECT POWER-UP RECALL The STK11C88 draws significantly less current when it is cycled at times longer than 50ns. Figure 2 shows the relationship between ICC and READ cycle time. Worst-case current consumption is shown for both CMOS and TTL input levels (commercial temperature range, VCC = 5.5V, 100% duty cycle on chip enable). Figure 3 shows the same relationship for WRITE cycles. If the chip enable duty cycle is less than 100%, only standby current is drawn when the chip is disabled. The overall average current drawn by the STK11C88 depends on the following items: 1) CMOS vs. TTL input levels; 2) the duty cycle of chip enable; 3) the overall cycle rate for accesses; 4) the ratio of READs to WRITEs; 5) During power up, or after any low-power condition (VCC < VRESET), an internal RECALL request will be latched. When VCC once again exceeds the sense voltage of VSWITCH, a RECALL cycle will automatically be initiated and will take tRESTORE to complete. If the STK11C88 is in a WRITE state at the end of power-up RECALL, the SRAM data will be corrupted. To help avoid this situation, a 10K Ohm resistor should be connected either between W and system VCC or between E and system VCC. The STK11C88 offers hardware protection against inadvertent STORE operation during low-voltage conditions. When VCC < VSWITCH, all software STORE operations are inhibited. LOW AVERAGE ACTIVE POWER the operating temperature; 6) the Vcc level; and 7) I/ O loading. Average Active Current (mA) 100 80 60 40 TTL 20 CMOS 0 50 ) 100 July 1999 5-8 100 150 Cycle Time (ns) 200 STK11C88 ORDERING INFORMATION STK11C88 - W 25 I Temperature Range Blank = Commercial (0 to 70°C) I = Industrial (–40 to 85°C) Access Time 20 = 20ns (Commercial only) 25 = 25ns 35 = 35ns 45 = 45ns Package W = Plastic 28-pin 600 mil DIP P = Plastic 28-pin 300 mil DIP S = Plastic 28-pin 350 mil SOIC N = Plastic 28-pin 300 mil SOIC July 1999 5-9