STK17T88 32K x 8 AutoStore™ nvSRAM with Real Time Clock Features Description ■ nvSRAM Combined With Integrated Real-Time Clock Functions (RTC, Watchdog Timer, Clock Alarm, Power Monitor) The Cypress STK17T88 combines a 256 Kb nonvolatile static RAM (nvSRAM) with a full-featured real-time clock in a reliable, monolithic integrated circuit. ■ Capacitor or Battery Backup for RTC ■ 25, 45 ns Read Access and R/W Cycle Time The 256 Kb nvSRAM is a fast static RAM with a nonvolatile Quantum Trap storage element included with each memory cell. ■ Unlimited Read/Write Endurance ■ Automatic Nonvolatile STORE on Power Loss ■ Nonvolatile STORE Under Hardware or Software Control ■ Automatic RECALL to SRAM on Power Up ■ Unlimited RECALL Cycles ■ 200K STORE Cycles ■ 20-Year Nonvolatile Data Retention ■ Single 3V +20%, -10% Power Supply ■ Commercial and Industrial Temperatures ■ 48-pin 300-mil SSOP Package (RoHS-Compliant) The SRAM provides the fast access and cycle times, ease of use and unlimited read and write endurance of a normal SRAM. Data transfers automatically to the nonvolatile storage cells when power loss is detected (the STORE operation). On power up, data is automatically restored to the SRAM (the RECALL operation). Both STORE and RECALL operations are also available under software control. The real time clock function provides an accurate clock with leap year tracking and a programmable, high accuracy oscillator. The Alarm function is programmable for one-time alarms or periodic minutes, hours, or days alarms. There is also a programmable watchdog timer for processor control. Logic Block Diagram VCC A5 A6 A7 A8 A9 A11 A12 A13 A14 ROW DECODER DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 INPUT BUFFERS Quantum Trap 512 X 512 VCAP POWER CONTROL STORE STATIC RAM ARRAY 512 X 512 STORE/ RECALL CONTROL RECALL VRTCbat VRTCcap HSB SOFTWARE DETECT A13 – A0 COLUMN I/O COLUMN DEC RTC X1 X2 INT A 0 A 1 A 2 A 3 A 4 A10 MUX A14 – A0 G E W Cypress Semiconductor Corporation Document Number: 001-52040 Rev. *A • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised March 17, 2009 [+] Feedback STK17T88 Pin Configurations Figure 1. 48-Pin SSOP V CAP 1 48 NC A 14 2 47 V CC NC 3 46 HSB A 12 A7 4 5 45 44 A6 A5 6 43 W A 13 A6 7 42 A9 INT 8 41 NC A4 9 40 A 11 NC 10 39 NC NC 11 38 NC NC V SS 12 37 NC 13 36 NC 14 35 (TOP) 15 34 V SS NC V RTCcap DQ 0 16 33 DQ 6 A3 A2 17 32 G 18 31 A 10 A1 19 30 E A0 DQ 1 DQ 2 20 29 21 28 DQ 7 DQ 5 27 X1 22 23 26 DQ 4 DQ 3 X2 24 25 V CC V RTCbat Relative PCB Area Usage[1] Pin Descriptions Pin Name IO Type Description A14-A0 Input Address: The 15 address inputs select one of 32,768 bytes in the nvSRAM array or one of 16 bytes in the clock register map. DQ7-DQ0 I/O Data: Bi-directional 8-bit data bus for accessing the nvSRAM and RTC. E Input Chip Enable: The active low E input selects the device. W Input Write Enable: The active low W enables data on the DQ pins to be written to the address location selected on the falling edge of E. G Input Output Enable: The active low G input enables the data output buffers during read cycles. De-asserting G high caused the DQ pins to tri-state. X1 Output Crystal Connection, drives crystal on startup. X2 Input VRTCcap Power Supply Capacitor supplied backup RTC supply voltage (Left unconnected if VRTCbat is used). VRTCbat Power Supply Battery supplied backup RTC supply voltage (Left unconnected if VRTCcap is used). VCC Power Supply Power: 3.0V, +20%, -10% HSB I/O Hardware Store Busy: When low this output indicates a Store is in progress. When pulled low external to the chip, it initiates a nonvolatile STORE operation. A weak pull up resistor keeps this pin high if not connected. (Connection Optional). INT Output Interrupt Control: Can be programmed to respond to the clock alarm, the watchdog timer and the power monitor. Programmable to either active high (push/pull) or active low (open-drain) VCAP Power Supply Autostore™ Capacitor: Supplies power to nvSRAM during power loss to store data from SRAM to nonvolatile storage elements. VSS Power Supply Ground NC No Connect Crystal Connection for 32.768 kHz crystal. Unlabeled pins have no internal connections. Note 1. For detailed package size specifications, see Package Diagram on page 21. Document Number: 001-52040 Rev. *A Page 2 of 22 [+] Feedback STK17T88 Absolute Maximum Ratings Note: Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Voltage on Input Relative to Ground.................–0.5V to 4.1V Voltage on Input Relative to VSS ...........–0.5V to (VCC + 0.5V) Voltage on DQ0-7 or HSB ......................–0.5V to (VCC + 0.5V) Temperature under Bias ............................... –55°C to 125°C Junction Temperature ................................... –55°C to 140°C Storage Temperature .................................... –65°C to 150°C Power Dissipation............................................................. 1W DC Output Current (1 output at a time, 1s duration).... 15 mA RF (SSOP-48) Package Thermal Characteristics θjc 6.2 C/W; θja 51.1 [0fpm], 44.7 [200fpm], 41.8 C/W [500fpm] DC Characteristics (VCC = 2.7V-3.6V) Symbol Parameter Commercial Min Max Industrial Min Max Units Notes ICC1 Average VCC Current 65 50 70 55 mA mA tAVAV = 25 ns tAVAV = 45 ns Dependent on output loading and cycle rate. Values obtained without output loads. ICC2 Average VCC Current during STORE 3 3 mA All Inputs Don’t Care, VCC = max Average current for duration of STORE cycle (tSTORE) ICC3 Average VCC Current at tAVAV = 200ns 3V, 25°C, Typical 10 10 mA W ≥ (V CC – 0.2V) All Other Inputs Cycling at CMOS Levels Dependent on output loading and cycle rate. Values obtained without output loads. ICC4 Average VCAP Current during AutoStore™ Cycle 3 3 mA All Inputs Don’t Care Average current for duration of STORE cycle (tSTORE) ISB VCC Standby Current (Standby, Stable CMOS Levels) 3 3 mA E ≥ (VCC -0.2V) All Others VIN≤ 0.2V or ≥ (VCC-0.2V) Standby current level after nonvolatile cycle complete IILK Input Leakage Current ±1 ±1 µA VCC = max VIN = VSS to VCC IOLK Off-State Output Leakage Current ±1 ±1 µA VCC = max VIN = VSS to VCC, E or G ≥ VIH VIH Input Logic “1” Voltage 2.0 VCC + 0.5 2.0 VCC + 0.5 V All Inputs VIL Input Logic “0” Voltage VSS –0.5 0.8 VSS –0.5 0.8 V All Inputs Note:The HSB pin has IOUT=-10uA for VOH of 2.4V, this parameter is characterized but not tested. Note:The INT is open-drain and does not source or sink high current when interrupt Register bit D3 is below. Document Number: 001-52040 Rev. *A Page 3 of 22 [+] Feedback STK17T88 DC Characteristics (continued) (VCC = 2.7V-3.6V) Symbol Parameter Commercial Min Industrial Max Min VOH Output Logic “1” Voltage 2.4 VOL Output Logic “0” Voltage TA Operating Temperature 0 70 VCC Operating Voltage 2.7 VCAP Storage Capacitance 17 NVC Nonvolatile STORE operations 200 200 DATAR Data Retention 20 20 Max 2.4 Units Notes V IOUT = – 2 mA 0.4 V IOUT = 4 mA –40 85 °C 3.6 2.7 3.6 V 3.0V +20%, -10% 57 17 57 µF Between VCAP pin and VSS, 5V rated. 0.4 K Years At 55°C AC Test Conditions Input Pulse Levels ....................................................0V to 3V Input Rise and Fall Times ...................................................≤ 5ns Input and Output Timing Reference Levels .................... 1.5V Output Load..................................See Figure 2 and Figure 3 Capacitance Symbol Parameter[2] Max Units Conditions CIN Input Capacitance 7 pF ∆V = 0 to 3V COUT Output Capacitance 7 pF ∆V = 0 to 3V Figure 2. AC Output Loading Figure 3. AC Output Loading for Tristate Specs (THZ, tLZ, tWLQZ, tWHQZ, tGLQX, tGHQZ) Note 2. These parameters are guaranteed but not tested. Document Number: 001-52040 Rev. *A Page 4 of 22 [+] Feedback STK17T88 RTC DC Characteristics Commercial Symbol Industrial Parameter Units Min Max Min Notes Max IBAK RTC Backup Current — 300 — 350 nA From either VRTCcap or VRTCbat VRTCbat RTC Battery Pin Voltage 1.8 3.3 1.8 3.3 V Typical = 3.0 Volts during normal operation VRTCcap RTC Capacitor Pin Voltage 1.2 2.7 1.2 2.7 V Typical = 2.4 Volts during normal operation tOSCS RTC Oscillator time to start — 10 — 10 sec At Minimum Temperature from Power up or Enable — 5 — 5 sec At 25°C from Power up or Enable Y1 C2 RF C1 Figure 4. RTC Component Configuration X1 X2 Recommended Values Y1 = 32.768 KHz RF = 10M Ohm C1 = 0 (install cap footprint, but leave unloaded) C2 = 56 pF ± 10% (do not vary from this value) Document Number: 001-52040 Rev. *A Page 5 of 22 [+] Feedback STK17T88 SRAM READ Cycles #1 and #2 Symbols NO. STK17T88-25 STK17T88-45 Min Min Parameter #1 #2 1 Alt. tELQV tACS Chip Enable Access Time Units Max 25 Max 45 ns 2 tAVAV[3] tELEH[5] tRC Read Cycle Time 3 tAVQV[4] tAVQV[6] tAA Address Access Time 25 45 ns tGLQV tOE Output Enable to Data Valid 12 20 ns tAXQX tOH Output Hold after Address Change 3 3 ns 6 tELQX tLZ Address Change or Chip Enable to Output Active 3 3 ns 7 tEHQZ tHZ Address Change or Chip Disable to Output Inactive 8 tGLQX tOLZ Output Enable to Output Active 9 tGHQZ[5] tOHZ Output Disable to Output Inactive 10 tELICCL[3] tPA Chip Enable to Power Active tPS Chip Disable to Power Standby 4 5 11 tAXQX[4] tEHICCH [3] 25 45 10 ns 15 0 0 10 ns 15 0 0 25 ns ns ns 45 ns Figure 5. SRAM READ Cycle #1: Address Controlled[3,4,6] 2 tAVAV ADDRESS 3 tAVQV 5 tAXQX DQ (DATA OUT) DATA VALID Figure 6. SRAM READ Cycle #2: E and G Controlled[6] 2 29 1 11 6 7 3 9 4 8 10 Notes 3. W must be high during SRAM READ cycles. 4. Device is continuously selected with E and G both low 5. Measured ± 200mV from steady state output voltage. 6. HSB must remain high during READ and WRITE cycles. Document Number: 001-52040 Rev. *A Page 6 of 22 [+] Feedback STK17T88 SRAM WRITE Cycles #1 and #2 Symbols NO. STK17T88-25 STK17T88-45 Min Min Parameter #1 #2 Units Alt. Max Max 12 tAVAV tAVAV tWC Write Cycle Time 25 45 ns 13 tWLWH tWLEH tWP Write Pulse Width 20 30 ns 14 tELWH tELEH tCW Chip Enable to End of Write 20 30 ns 15 tDVWH tDVEH tDW Data Set-up to End of Write 10 15 ns 16 tWHDX tEHDX tDH Data Hold after End of Write 0 0 ns 17 tAVWH tAVEH tAW Address Set-up to End of Write 20 30 ns 18 tAVWL tAVEL tAS Address Set-up to Start of Write 0 0 ns 19 tWHAX tEHAX tWR Address Hold after End of Write 0 0 ns 20 tWLQZ tWZ Write Enable to Output Disable 21 tWHQX tOW Output Active after End of Write 10 3 15 3 ns ns Figure 7. SRAM WRITE Cycle #1: W Controlled[7, 8] 12 tAVAV ADDRESS 19 tWHAX 14 tELWH E 17 tAVWH 18 tAVWL 13 tWLWH W 15 tDVWH DATA IN 16 tWHDX DATA VALID 20 tWLQZ DATA OUT 21 tWHQX HIGH IMPEDANCE PREVIOUS DATA Figure 8. SRAM WRITE Cycle #2: E Controlled[7, 8] 12 tAVAV ADDRESS 18 tAVEL 14 tELEH 19 tEHAX E 17 tAVEH 13 tWLEH W 15 tDVEH DATA IN DATA OUT 16 tEHDX DATA VALID HIGH IMPEDANCE Notes 7. If W is low when E goes low, the outputs remain in the high-impedance state. 8. E or W must be ≥ VIH during address transitions. Document Number: 001-52040 Rev. *A Page 7 of 22 [+] Feedback STK17T88 AutoStore/Power Up RECALL Symbols STK17T88 NO. Parameter Standard Units Notes 40 ms 9 STORE Cycle Duration 12.5 ms 10, 11 2.65 V Alternate Min 22 tHRECALL 23 tSTORE 24 VSWITCH Low Voltage Trigger Level 25 VCCRISE VCC Rise Time Max Power up RECALL Duration tHLHZ µS 150 Figure 9. AutoStore Power Up RECALL 25 23 22 23 22 NOTE: Read and Write cycles will be ignored during STORE, RECALL and while VCC is below VSWITCH Notes 9. tHRECALL starts from the time VCC rises above VSWITCH 10. If an SRAM WRITE has not taken place since the last nonvolatile cycle, no STORE will take place 11. Industrial Grade Devices require 15 ms Max. Document Number: 001-52040 Rev. *A Page 8 of 22 [+] Feedback STK17T88 Software-Controlled STORE/RECALL Cycle In the following table, the software controlled STORE and RECALL cycle parameters are listed. [12, 13] Symbols NO. STK17T88-35 STK17T88-45 Min Min Parameter E Cont Alternate Max Units Notes 13 Max 26 tAVAV tRC STORE / RECALL Initiation Cycle Time 25 45 ns 27 tAVEL tAS Address Set-up Time 0 0 ns 28 tELEH tCW Clock Pulse Width 20 30 ns 29 tEHAX Address Hold Time 1 1 ns 30 tRECALL RECALL Duration 100 100 ms Figure 10. Software Store/Recall Cycle: E CONTROLLED[13] 26 26 27 28 29 23 30 Notes 12. The software sequence is clocked on the falling edge of E controlled READs 13. The six consecutive addresses must be read in the order listed in the Software STORE/RECALL Mode Selection Table. W must be high during all six consecutive cycles. Document Number: 001-52040 Rev. *A Page 9 of 22 [+] Feedback STK17T88 Hardware STORE Cycle Symbols STK17T88 NO. Parameter Standard 31 tDELAY 32 tHLHX Alternate tHLQZ Min Max Hardware STORE to SRAM Disabled 1 70 Hardware STORE Pulse Width 15 Units Notes µs 14 ns Figure 11. Hardware STORE Cycle 32 23 31 Soft Sequence Commands Symbols Parameter STK17T88 Units Notes µs 15, 16 NO. Standard 33 tSS Min Soft Sequence Processing Time Max 70 Figure 12. Soft Sequence Command 33 33 Notes 14. On a hardware STORE initiation, SRAM operation continues to be enabled for time tDELAY to allow read/write cycles to complete 15. This is the amount of time that it takes to take action on a soft sequence command. Vcc power must remain high to effectively register command. 16. Commands like Store and Recall lock out I/O until operation is complete which further increases this time. See specific command Document Number: 001-52040 Rev. *A Page 10 of 22 [+] Feedback STK17T88 MODE Selection E W G A14-A0 Mode I/O Power H X X X Not Selected Output High Z Standby L H L X Read SRAM Output Data Active L L X X Write SRAM Input Data Active L H L 0x0E38 0x31C7 0x03E0 0x3C1F 0x303F Read SRAM Read SRAM Read SRAM Read SRAM Read SRAM Output Data Output Data Output Data Output Data Output Data Active 0x0FC0 Nonvolatile Store Output High Z ICC2 0x0E38 0x31C7 0x03E0 0x3C1F 0x303F 0x0C63 Read SRAM Read SRAM Read SRAM Read SRAM Read SRAM Nonvolatile Recall Output Data Output Data Output Data Output Data Output Data Output High Z Active L H L Notes 17,18, 19 17,18, 19 Notes 17. The six consecutive addresses must be in the order listed. W must be high during all six consecutive cycles to enable a nonvolatile cycle. 18. While there are 15 addresses on the STK17T88, only the lower 13 are used to control software modes. 19. I/O state depends on the state of G. The I/O table shown assumes G low. Document Number: 001-52040 Rev. *A Page 11 of 22 [+] Feedback STK17T88 nvSRAM Operation (activated by HSB), Software Store (activated by an address sequence), and AutoStore (on power down). The STK17T88 nvSRAM is made up of two functional components paired in the same physical cell. These are the SRAM memory cell and a nonvolatile QuantumTrap™ cell. The SRAM memory cell operates like a standard fast static RAM. Data in the SRAM can be transferred to the nonvolatile cell (the STORE operation), or from the nonvolatile cell to SRAM (the RECALL operation). This unique architecture allows all cells to be stored and recalled in parallel. During the STORE and RECALL operations SRAM READ and WRITE operations are inhibited. The STK17T88 supports unlimited read and writes like a typical SRAM. In addition, it provides unlimited RECALL operations from the nonvolatile cells and up to 200K STORE operations. AutoStore operation, a unique feature of Cypress QuanumTrap technology that is a standard feature on the STK17T88. SRAM READ The STK17T88 performs a READ cycle whenever E and G are low while W and HSB are high. The address specified on pins A0-14 determine which of the 32,768 data bytes are accessed. When the READ is initiated by an address transition, the outputs are valid after a delay of tAVQV (READ cycle #1). If the READ is initiated by E and G, the outputs are valid at tELQV or at tGLQV, whichever is later (READ cycle #2). The data outputs repeatedly respond to address changes within the tAVQV access time without the need for transitions on any control input pins, and remain valid until another address change or until E or G is brought high, or W and HSB is brought low. Figure 13. AutoStore Mode W 0.1µF VCAP VCC 10k Ohm VCC VCAP During normal operation, the device draws current from VCC to charge a capacitor connected to the VCAP pin. This stored charge is used by the chip to perform a single STORE operation. If the voltage on the VCC pin drops below VSWITCH, the part automatically disconnects the VCAP pin from VCC. A STORE operation is initiated with power provided by the VCAP capacitor. Figure 5 shows the proper connection of the storage capacitor (VCAP) for automatic store operation. Refer to the DC Characteristics table for the size of the capacitor. The voltage on the VCAP pin is driven to 5V by a charge pump internal to the chip. A pull up should be placed on W to hold it inactive during power up. To reduce unneeded nonvolatile stores, AutoStore and Hardware Store operations are ignored unless at least one WRITE operation has taken place since the most recent STORE or RECALL cycle. Software initiated STORE cycles are performed regardless of whether a WRITE operation has taken place. The HSB signal can be monitored by the system to detect an AutoStore cycle is in progress. Hardware STORE (HSB) Operation The STK17T88 provides the HSB pin for controlling and acknowledging the STORE operations. The HSB pin can be used to request a hardware STORE cycle. When the HSB pin is driven low, the STK17T88 conditionally initiates a STORE operation after tDELAY. An actual STORE cycle only begins if a WRITE to the SRAM took place since the last STORE or RECALL cycle. The HSB pin has a very resistive pull up and is internally driven low to indicate a busy condition while the STORE (initiated by any means) is in progress. This pin should be externally pulled up if it is used to drive other inputs. SRAM READ and WRITE operations that are in progress when HSB is driven low by any means are given time to complete before the STORE operation is initiated. After HSB goes low, the STK17T88 continues to allow SRAM operations for tDELAY. During tDELAY, multiple SRAM READ operations may take place. If a WRITE is in progress when HSB is pulled low, it is allowed a time, tDELAY, to complete. However, any SRAM WRITE cycles requested after HSB goes low will be inhibited until HSB returns high. SRAM WRITE A WRITE cycle is performed whenever E and W are low and HSB is high. The address inputs must be stable prior to entering the WRITE cycle and must remain stable until either E or W goes high at the end of the cycle. The data on the common I/O pins DQ0-7 are written into memory if it is valid tDVWH before the end of a W controlled WRITE or tDVEH before the end of an E controlled WRITE. It is recommended that G be kept high during the entire WRITE cycle to avoid data bus contention on common I/O lines. If G is left low, internal circuitry turns off the output buffers tWLQZ after W goes low. AutoStore Operation During any STORE operation, regardless of how it was initiated, the STK17T88 will continue to drive the HSB pin low, releasing it only when the STORE is complete. Upon completion of the STORE operation, the STK17T88 will remain disabled until the HSB pin returns high. If HSB is not used, it should be left unconnected. Hardware Recall (POWER UP) During power up or after any low-power condition (VCC<VSWITCH), an internal RECALL request will be latched. When VCC once again exceeds the sense voltage of VSWITCH, a RECALL cycle is automatically initiated and takes tHRECALL to complete. The STK17T88 stores data to nvSRAM using one of three storage operations. These three operations are Hardware Store Document Number: 001-52040 Rev. *A Page 12 of 22 [+] Feedback STK17T88 Software STORE Data can be transferred from the SRAM to the nonvolatile memory by a software address sequence. The STK17T88 software STORE cycle is initiated by executing sequential E controlled READ cycles from six specific address locations in exact order. During the STORE cycle, previous data is erased and then the new data is programmed into the nonvolatile elements. Once a STORE cycle is initiated, further memory inputs and outputs are disabled until the cycle is completed. To initiate the software STORE cycle, the following READ sequence must be performed: 1. Read address 0x0E38, Valid READ 2. Read address 0x31C7, Valid READ 3. Read address 0x03E0, Valid READ 4. Read address 0x3C1F, Valid READ 5. Read address 0x303F, Valid READ 6. Read address 0x0FC0, Initiate STORE cycle Once the sixth address in the sequence has been entered, the STORE cycle commences and the chip is disabled. It is important that READ cycles and not WRITE cycles be used in the sequence. After the tSTORE cycle time has been fulfilled, the SRAM is again activated for READ and WRITE operation. If the STK17T88 is in a WRITE mode (both E and W low) at power up, after a RECALL, or after a STORE, the WRITE is inhibited until a negative transition on E or W is detected. This protects against inadvertent writes during power up or brown out conditions. Noise Considerations The STK17T88 is a high-speed memory and so must have a high-frequency bypass capacitor of 0.1 µF connected between both VCC pins and VSS ground plane with no plane break to chip VSS. Use leads and traces that are as short as possible. As with all high-speed CMOS ICs, careful routing of power, ground, and signals reduce circuit noise. Preventing AutoStore Because of the use of nvSRAM to store critical RTC data, the AutoStore function can not be disabled on the STK17T88. Best Practices nvSRAM products have been used effectively for over 15 years. While ease-of-use is one of the product’s main system values, experience gained working with hundreds of applications has resulted in the following suggestions as best practices: ■ The nonvolatile cells in an nvSRAM are programmed on the test floor during final test and quality assurance. Incoming inspection routines at customer or contract manufacturer’s sites sometimes reprograms these values. Final NV patterns are typically repeating patterns of AA, 55, 00, FF, A5, or 5A. End product’s firmware should not assume an NV array is in a set programmed state. Routines that check memory content values to determine first time system configuration, cold or warm boot status, etc. should always program a unique NV pattern (e.g., complex 4-byte pattern of 46 E6 49 53 hex or more random bytes) as part of the final system manufacturing test to ensure these system routines work consistently. ■ Power up boot firmware routines should rewrite the nvSRAM into the desired state (autostore enabled, etc.). While the nvSRAM is shipped in a preset state, best practice is to again rewrite the nvSRAM into the desired state as a safeguard against events that might flip the bit inadvertently (program bugs, incoming inspection routines, etc.). ■ The OSCEN bit in the Calibration register at 0x7FF8 should be set to 1 to preserve battery life when the system is in storage (see Stopping and Starting the RTC Oscillator on page 14. ■ The VCAP value specified in this datasheet includes a minimum and a maximum value size. Best practice is to meet this requirement and not exceed the max VCAP value because the nvSRAM internal algorithm calculates VCAP charge time based on this max Vcap value. Customers that want to use a larger VCAP value to make sure there is extra store charge and store time should discuss their Vcap size selection with Cypress to understand any impact on the VCAPvoltage level at the end of a tRECALL period. Software RECALL Data can be transferred from the nonvolatile memory to the SRAM by a software address sequence. A software RECALL cycle is initiated with a sequence of READ operations in a manner similar to the software STORE initiation. To initiate the RECALL cycle, the following sequence of E controlled READ operations must be performed: 1. Read address 0x0E38, Valid READ 2. Read address 0x31C7, Valid READ 3. Read address 0x03E0, Valid READ 4. Read address 0x3C1F, Valid READ 5. Read address 0x303F, Valid READ 6. Read address 0x0C63, Initiate RECALL cycle Internally, RECALL is a two-step procedure. First, the SRAM data is cleared, and second, the nonvolatile information is transferred into the SRAM cells. After the tRECALL cycle time, the SRAM is again ready for READ or WRITE operations. The RECALL operation in no way alters the data in the nonvolatile storage elements. Data Protection The STK17T88 protects data from corruption during low-voltage conditions by inhibiting all externally initiated STORE and WRITE operations. The low-voltage condition is detected when VCC<VSWITCH. Document Number: 001-52040 Rev. *A Page 13 of 22 [+] Feedback STK17T88 Real Time Clock The clock registers maintain time up to 9,999 years in one-second increments. The user can set the time to any calendar time and the clock automatically keeps track of days of the week and month, leap years, and century transitions. There are eight registers dedicated to the clock functions which are used to set time with a write cycle and to read time during a read cycle. These registers contain the Time of Day in BCD format. Bits defined as “0” are currently not used and are reserved for future use by Cypress. Reading the Clock The user should halt internal updates to the real time clock registers before reading clock data to prevent reading of data in transition. Stopping the internal register updates does not affect clock accuracy. Write a “1” to the read bit “R” (in the Flags register at 0x7FF0) to capture the current time in holding registers. Clock updates do not restart until a “0” is written to the read bit. The RTC registers can now be read while the internal clock continues to run. Within 20ms after a “0” is written to the read bit, all real time clock registers are simultaneously updated. Setting the Clock Set the write bit “W” (in the Flags register at 0x7FF0) to a “1” enable the time to be set. The correct day, date and time can then be written into the real time clock registers in 24-hour BCD format. The time written is referred to as the “Base Time.” This value is stored in nonvolatile registers and used in calculation of the current time. Reset the write bit to “0” to transfer the time to the actual clock counters, The clock starts counting at the new base time. Backup Power The RTC is intended to keep time even when system power is lost. When primary power, VCC, drops below VSWITCH, the real time clock switches to the backup power supply connected to either the VRTCcap or VRTCbat pin. The clock oscillator uses a maximum of 300 nanoamps at 2 volts to maximize the backup time available from the backup source. You can power the real time clock with either a capacitor or a battery. Factors to be considered when choosing a backup power source include the expected duration of power outages and the cost and reliability trade-off of using a battery versus a capacitor. If you select a capacitor power source, connect the capacitor to the VRTCcap pin and leave the VRTCbat pin unconnected. Capacitor backup time values based on maximum current specs are shown below. Nominal times are approximately 3 times longer. Capacitor Value Backup Time 0.1 F 72 hours 0.47 F 14 days 1.0 F 30 days Document Number: 001-52040 Rev. *A A capacitor has the obvious advantage of being more reliable and not containing hazardous materials. The capacitor is recharged every time the power is turned on so that the real time clock continues to have the same backup time over years of operation If you select a battery power source, connect the battery to the VRTCbat pin and leave the VRTCcap pin unconnected. A 3V lithium is recommended for this application. The battery capacity should be chosen for the total anticipated cumulative down-time required over the life of the system. The real time clock is designed with a diode internally connected to the VRTCbat pin. This prevents the battery from ever being charged by the circuit. Stopping and Starting the RTC Oscillator The OSCEN bit in Calibration register at 0x7FF8 enables RTC oscillator operation. This bit is nonvolatile and shipped to customers in the “enabled” state (set to 0). OSCEN should be set to a 1 to preserve battery life while the system is in storage. This turns off the oscillator circuit extending the battery life. If the OSCEN bit goes from disabled to enabled, it typically takes 5 seconds (10 seconds max) for the oscillator to start. The STK17T88 has the ability to detect oscillator failure due to loss of backup power. The failure is recorded by the OSCF (Oscillator Failed bit) of the Flags register (at address 0x7FF0). When the device is powered on (VCC goes above VSWITCH) the OSCEN bit is checked for “enabled” status. If the OSCEN bit is enabled and the oscillator is not active within 5 ms, the OSCF bit is set. The user should check for this condition and then write a 0 to clear the flag. When the OSCF flag bit, the real time clock registers are reset to the “Base Time” (see the section Setting the Clock on page 14, the value last written to the real time clock registers. The value of OSCF should be reset to 0 when the real time clock registers are written for the first time. This initializes the state of this bit since it may have become set when the system was first powered on. To reset OSCF, set the write bit “W” (in the Flags register at 0x7FF0) to a “1” to enable writes to the Flags register. Write a “0” to the OSCF bit and then reset the write bit to “0” to disable writes. Calibrating The Clock The RTC is driven by a quartz controlled oscillator with a nominal frequency of 32.768 KHz. Clock accuracy depends on the quality of the crystal specified (usually 35 ppm at 25 C). This error could equate to 1.53 minutes gain or loss per month. The STK17T88 employs a calibration circuit that can improve the accuracy to +1/-2 ppm at 25 C. The calibration circuit adds or subtracts counts from the oscillator divider circuit. The number of time pulses added or subtracted depends upon the value loaded into the five calibration bits found in Calibration register (at 0x7FF8). Adding counts speeds the clock up; subtracting counts slows the clock down. The Calibration bits occupy the five lower order bits of the register. These bits can be set to represent any value between 0 and 31 in binary form. Bit D5 is a Sign bit, where a “1” indicates positive calibration and a “0” indicates negative calibration. Calibration occurs during a 64 minute period. The first 62 minutes in the cycle may, once per Page 14 of 22 [+] Feedback STK17T88 minute, have one second either shortened by 128 or lengthened by 256 oscillator cycles. If a binary “1” is loaded into the register, only the first 2 minutes of the 64 minute cycle is modified; if a binary 6 is loaded, the first 12 are affected, and so on. Therefore each calibration step has the effect of adding 512 or subtracting 256 oscillator cycles for every 125,829,120 actual oscillator cycles. That is +4.068 or -2.034 ppm of adjustment per calibration step in the Calibration register. The calibration register value is determined during system test by setting the CAL bit in the Flags register (at 0x7FF0) to 1. This causes the INT pin to toggle at a nominal 512 Hz. This frequency can be measured with a frequency counter. Any deviation measured from the 512 Hz indicates the degree and direction of the required correction. For example, a reading of 512.01024 Hz would indicate a +20 ppm error, requiring a -10 (001010) to be loaded into the Calibration register. Note that setting or changing the calibration register does not affect the frequency test output frequency. To set or clear CAL, set the write bit “W” (in the Flags register at 0x7FF0) to a “1” to enable writes to the Flags register. Write a value to CAL and then reset the write bit to “0” to disable writes. The default Calibration register value from the factory is 00h. The user calibration value loaded is retained during a power loss. Alarm The alarm function compares a user-programmed alarm time/date (stored in registers 0x7FF1-5) with the real time clock time-of-day/date values. When a match occurs, the alarm flag (AF) is set and an interrupt is generated if the alarm interrupt is enabled. The alarm flag is automatically reset when the Flags register is read. Each of the alarm registers has a match bit as its MSB. Setting the match bit to a 1 disables this alarm register from the alarm comparison. When the match bit is 0, the alarm register is compared with the equivalent real time clock register. Using the match bits, an alarm can occur as specifically as one particular second on one day of the month or as frequently as once per minute. Note The product requires the match bit for seconds (0x7FF2, bit D7) be set to 0 for proper operation of the Alarm Flag and Interrupt. The alarm value should be initialized on power up by software since the alarm registers are not nonvolatile. To set or clear the Alarm registers, set the write bit “W” (in the Flags register at 0x7FF0) to a “1” to enable writes to the Alarm registers. Write an alarmvalue to the alarm registers and then reset the write bit to “0” to disable writes. Watchdog Timer The watchdog timer is designed to interrupt or reset the processor should its program get hung in a loop and not respond in a timely manner. The software must reload the watchdog timer before it counts down to zero to prevent this interrupt or reset. Document Number: 001-52040 Rev. *A The watchdog timer is a free-running-down counter that uses the 32Hz clock (31.25 ms) derived from the crystal oscillator. The watchdog timer function does not operate unless the oscillator is running. The watchdog counter is loaded with a starting value from the load register and then counts down to zero, setting the watchdog flag (WDF) and generating an interrupt if the watchdog interrupt is enabled. The watchdog flag bit is reset when the Flags register is read. The operating software would normally reload the counter by setting the watchdog strobe bit (WDS) to 1 within the timing interval programmed into the load register. To use the watchdog timer to reset the processor on timeout, the INT is tied to processor master reset and Interrupt register is programmed to 24h to enable interrupts to pulse the reset pin on timeout. To load the watchdog timer, set a new value into the load register by writing a “0” to the watchdog write bit (WDW) of the watchdog register (at 0x7FF7). Then load a new value into the load register. Once the new value is loaded, the watchdog write bit is then set to 1 to disable watchdog writes. The watchdog strobe bit (WDS) is set to 1 to load this value into the watchdog timer. Note: Setting the load register to zero disables the watchdog timer function. The system software should initialize the watchdog load register on power up to the desired value since the register is not nonvolatile. Power Monitor The STK17T88 provides a power monitor function. The power monitor is based on an internal band-gap reference circuit that compares the VCC voltage to VSWITCH. When the power supply drops below VSWITCH, the real time clock circuit is switched to the backup supply (battery or capacitor). When operating from the backup source, no data may be read or written and the clock functions are not available to the user. The clock continues to operate in the background. Updated clock data is available to the user tHRECALL delay after VCC has been restored to the device. When the power is lost, the PF flag in the Flags register is set to indicate the power failure and an interrupt is generated if the power fail interrupt is enabled (interrupt register=20h). The INT line would normally be tied to the processor master reset input to perform power-off reset. Interrupts The STK17T88 has a Flags register, Interrupt register, and interrupt logic that can interrupt the microcontroller or general a power up master reset signal. There are three potential interrupt sources: the watchdog timer, the power monitor, and the clock alarm. Each can be individually enabled to drive the INT pin by setting the appropriate bit in the Interrupt register. In addition, each has an associated flag bit in the Flags register that the host processor can read to determine the interrupt source. Two bits in the interrupt register determine the operation of the INT pin driver. Page 15 of 22 [+] Feedback STK17T88 Figure 15 is a functional diagram of the interrupt logic. High/Low (H/L). When set to a 1, the INT pin is active high and the driver mode is push-pull. The INT pin can drive high only when VCC>VSWITCH. When set to a 0, the INT pin is active low and the drive mode is open-drain. The active low (open drain) output is maintained even when power is lost. Figure 15. Interrupt Block Diagram WDF Watchdog Timer Power Monitor WIE PF P/L PFE Pin Driver H/L VINT VCC INT VSS Pulse/Level (P/L). When set to a 1, the INT pin is driven for approximately 200 ms when the interrupt occurs. The pulse is reset when the Flags register is read. When P/L is set to a 0, the INT pin is driven high or low (determined by H/L) until the Flags register is read. AF Clock Alarm AIE The Interrupt register is loaded with the default value 00h at the factory. The user should configure the Interrupt register to the value desired for their desired mode of operation. Once configured, the value is retained during power failures. Interrupt Register Flags Register Watchdog Interrupt Enable (WIE). When set to 1, the watchdog timer drives the INT pin when a watchdog time-out occurs. When WIE is set to 0, the watchdog time-out only sets the WDF flag bit. The Flags register has three flag bits: WDF, AF, and PF. These flags are set by the watchdog time-out, alarm match, or power fail monitor respectively. The processor can either poll this register or enable the interrupts to be informed when a flag is set. The flags are automatically reset once the register is read. Alarm Interrupt Enable (AIE). When set to 1, the INT pin is driven when an alarm match occurs. When set to 0, the alarm match only sets the AF flag bit. Power Fail Interrupt Enable (PFE). When set to 1, the INT pin is driven by a power fail signal from the power monitor. When set to 0, only the PF flag is set. Document Number: 001-52040 Rev. *A The Flags register is automatically loaded with the value 00h on power up (with the exception of the OSCF bit). Page 16 of 22 [+] Feedback STK17T88 RTC Register Map Register 0x7FFF 0x7FFE 0x7FFD 0x7FFC 0x7FFB 0x7FFA 0x7FF9 0x7FF8 D7 0 D6 D5 10s Years 0 0 0x7FF7 0 0 0 0 0 OSCEN [0] WDS WDW 0x7FF6 WIE[0] AIE[0] 0x7FF5 0x7FF4 0x7FF3 0x7FF2 0x7FF1 0x7FF0 M M M M 0 0 WDF 0 0 0 0 BCD Format Data D4 D3 D2 D0 Function / Range Years Months 10s Months 10s Day of Month 0 0 10s Hours 10s Minutes 10s Seconds Cal Sign D1 Years: 00-99 Months: 01-12 Day of Month Day of Week Hours Minutes Seconds Calibration [00000] Day of Month: 01-31 Day of week: 01-07 Hours: 00-23 Minutes: 00-59 Seconds: 00-59 Calibration values* 0 WDT PFE[0] 0 10s Alarm Date 10s Alarm Hours 10 Alarm Minutes 10 Alarm Seconds 10s Centuries AF PF OSCF H/L [1] 0 P/L [0] Watchdog* 0 Alarm Day Alarm Hours Alarm Minutes Alarm Seconds Centuries CAL[0] W[0] 0 Interrupts* R[0] Alarm, Day of Month: 01-31 Alarm, hours: 00-23 Alarm, minutes: 00-59 Alarm, seconds: 00-59 Centuries: 00-99 Flags* *A binary value, not a BCD value. 0 - Not implemented, reserved for future use. Default Settings of nonvolatile Calibration and Interrupt registers from factory Calibration Register=00h Interrupt Register=00h The User should configure to the desired value at startup or during operation and the value is then retained during a power failure. [ ] designates values shipped from the factory. See Stopping and Starting the RTC Oscillator on page 14. Document Number: 001-52040 Rev. *A Page 17 of 22 [+] Feedback STK17T88 Register Map Detail 0x7FFF 0x7FFE 0x7FFD 0x7FFC 0x7FFB 0x7FFA 0x7FF9 0x7FF8 OSCEN Calibration Sign Calibration 0x7FF7 WDS D7 D5 Real Time Clock – Years D4 D3 D2 D1 D0 10s Years Years Contains the lower two BCD digits of the year. Lower nibble contains the value for years; upper nibble contains the value for 10s of years. Each nibble operates from 0 to 9. The range for the register is 0-99. Real Time Clock – Months D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 10s Months Month Contains the BCD digits of the month. Lower nibble contains the lower digit and operates from 0 to 9; upper nibble (one bit) contains the upper digit and operates from 0 to 1. The range for the register is 1-12. Real Time Clock – Date D7 D6 D5 D4 D3 D2 D1 D0 0 0 10s Day of month Day of month Contains the BCD digits for the date of the month. Lower nibble contains the lower digit and operates from 0 to 9; upper nibble contains the upper digit and operates from 0 to 3. The range for the register is 1-31. Leap years are automatically adjusted for. Real Time Clock – Day D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 0 0 Day of week Lower nibble contains a value that correlates to day of the week. Day of the week is a ring counter that counts from 1 to 7 then returns to 1. The user must assign meaning to the day value, as the day is not integrated with the date. Real Time Clock – Hours D7 D6 D5 D4 D3 D2 D1 D0 0 0 10s Hours Hours Contains the BCD value of hours in 24 hour format. Lower nibble contains the lower digit and operates from 0 to 9; upper nibble (two bits) contains the upper digit and operates from 0 to 2. The range for the register is 0-23. Real Time Clock – Minutes D7 D6 D5 D4 D3 D2 D1 D0 0 10s Minutes Minutes Contains the BCD value of minutes. Lower nibble contains the lower digit and operates from 0 to 9; upper nibble contains the upper minutes digit and operates from 0 to 5. The range for the register is 0-59. Real Time Clock – Seconds D7 D6 D5 D4 D3 D2 D1 D0 0 10s Seconds Seconds Contains the BCD value of seconds. Lower nibble contains the lower digit and operates from 0 to 9; upper nibble contains the upper digit and operates from 0 to 5. The range for the register is 0-59. Calibration D7 D6 D5 D4 D3 D2 D1 D0 OSCEN 0 Calibratio Calibration n Sign Oscillator Enable. When set to 1, the oscillator is disabled. When set to 0, the oscillator is enabled. Disabling the oscillator saves battery/capacitor power during storage. Determines if the calibration adjustment is applied as an addition to or as a subtraction from the time-base. These five bits control the calibration of the clock. Watchdog Timer D7 D6 D5 D4 D3 D2 D1 D0 WDS WDW WDT Watchdog Strobe. Setting this bit to 1 reloads and restarts the watchdog timer. The bit is cleared automatically once the watchdog timer is reset. The WDS bit is write only. Reading it always will return a 0. Document Number: 001-52040 Rev. *A D6 Page 18 of 22 [+] Feedback STK17T88 Register Map Detail (continued) WDW WDT 0x7FF6 WIE AIE PFIE 0 H/L P/L 0x7FF5 M 0x7FF4 M 0x7FF3 M 0x7FF2 M 0x7FF1 Watchdog Write Enable. Set this bit to 1 to disable writing of the watchdog time-out value (WDT5-WDT0). This allows the user to strobe the watchdog without disturbing the time-out value. Setting this bit to 0 allows bits 5-0 to be written. Watchdog time-out selection. The watchdog timer interval is selected by the 6-bit value in this register. It represents a multiplier of the 32 Hz count (31.25 ms). The range or time-out values is 31.25 ms (a setting of 1) to 2 seconds (setting of 3Fh). Setting the watchdog timer register to 0 disables the timer. These bits can be written only if the WDW bit was cleared to 0 on a previous cycle. Interrupt D7 D6 D5 D4 D3 D2 D1 D0 WIE AIE PFIE ABE H/L P/L 0 0 Watchdog Interrupt Enable. When set to 1 and a watchdog time-out occurs, the watchdog timer drives the INT pin and sets the WDF flag. When set to 0, the watchdog time-out only sets the WDF flag. Alarm Interrupt Enable. When set to 1, the alarm match drives the INT pin and sets the AF flag. When set to 0, the alarm match only sets the AF flag. Power-Fail Enable. When set to 1, a power failure drives the INT pin and sets the PF flag. When set to 0, a power failure only sets the PF flag. Reserved for Future Use High/Low. When set to a 1, the INT pin is driven active high. When set to 0, the INT pin is open drain, active low. Pulse/Level. When set to a 1, the INT pin is driven active (determined by H/L) by an interrupt source for approximately 200 ms. When set to a 0, the INT pin is driven to an active level (as set by H/L) until the Flags register is read. Alarm – Day D7 D6 D5 D4 D3 D2 D1 D0 M 0 10s Alarm Date Alarm Date Contains the alarm value for the date of the month and the mask bit to select or deselect the date value. Match. Setting this bit to 0 causes the date value to be used in the alarm match. Setting this bit to 1 causes the match circuit to ignore the date value. Alarm – Hours D7 D6 D5 D4 D3 D2 D1 D0 M 0 10s Alarm Hours Alarm Hours Contains the alarm value for the hours and the mask bit to select or deselect the hours value. Match. Setting this bit to 0 causes the hours value to be used in the alarm match. Setting this bit to 1 causes the match circuit to ignore the hours value. Alarm – Minutes D7 D6 D5 D4 D3 D2 D1 D0 M 10s Alarm Minutes Alarm Minutes Contains the alarm value for the minutes and the mask bit to select or deselect the minutes value. Match. Setting this bit to 0 causes the minutes value to be used in the alarm match. Setting this bit to 1 causes the match circuit to ignore the minutes value. Alarm – Seconds D7 D6 D5 D4 D3 D2 D1 D0 M 10s Alarm Seconds Alarm Seconds Contains the alarm value for the seconds and the mask bit to select or deselect the seconds’ value. Match. Setting this bit to 0 causes the seconds’ value to be used in the alarm match. Setting this bit to 1 causes the match circuit to ignore the seconds value. Real Time Clock – Centuries 10s Centuries Centuries Contains the BCD value of Centuries. Lower nibble contains the lower digit and operates from 0 to 9; upper nibble contains the upper centuries digit and operates from 0 to 9. The range for the register is 0-99 centuries. Document Number: 001-52040 Rev. *A Page 19 of 22 [+] Feedback STK17T88 Register Map Detail (continued) 0x7FF0 WDF AF PF OSCF CAL W R Flags D7 D6 D5 D4 D3 D2 D1 D0 WDF AF PF OSCF 0 CAL W R Watchdog Timer Flag. This read-only bit is set to 1 when the watchdog timer is allowed to reach 0 without being reset by the user. It is cleared to 0 when the Flags register is read or on power up Alarm Flag. This read-only bit is set to 1 when the time and date match the values stored in the alarm registers with the match bits = 0. It is cleared when the Flags register is read or on power up Power-fail Flag. This read-only bit is set to 1 when power falls below the power-fail threshold VSWITCH. It is cleared to 0 when the Flags register is read or on power up. Oscillator Fail Flag. Set to 1 on power up only if the oscillator is enabled and not running in the first 5ms of operation. This indicates that the RTC backup power failed and the clock value is no longer valid. The user must reset this bit to 0 to clear this condition. Calibration Mode. When set to 1, a 512Hz square wave is output on the INT pin. When set to 0, the INT pin resumes normal operation. This bit defaults to 0 (disabled) on power up. Write Time. Setting the W bit to 1 freezes updates of the RTC registers. The user can then write to the RTC registers, Alarm registers, Calibration register, Interrupt register and Flags register. Setting the W bit to 0 disables writes to the registers and causes the contents of the real time clock registers to be transferred to the timekeeping counters if the time has changed (a new base time is loaded). The bit defaults to 0 on power up. Read Time. Setting the R bit to 1 captures the current time in holding registers so that clock updates are not during the reading process. Set the R bit to 0 to enable the holding register to resume clock updates. The bit defaults to 0 on power up. Commercial and Industrial Ordering Information STK17T88 - R F 45 I TR Packaging Option: TR = Tape and Reel Blank = Tube Temperature Range: C - Commercial (0 to 70°C) I - Industrial (-40 to 85°C) Speed: 25 - 25 ns 45 - 45 ns Lead Finish F = 100% Sn (Matte Tin) RoHS Compliant Package: R = Plastic 48-pin 330 mil SSOP Ordering Codes Ordering Code STK17T88-RF25 STK17T88-RF45 STK17T88-RF25TR STK17T88-RF45TR STK17T88-RF25I STK17T88-RF45I STK17T88-RF25ITR STK17T88-RF45ITR Description 3.3V 32Kx8 AutoStore nvSRAM+RTC 3.3V 32Kx8 AutoStore nvSRAM+RTC 3.3V 32Kx8 AutoStore nvSRAM+RTC 3.3V 32Kx8 AutoStore nvSRAM+RTC 3.3V 32Kx8 AutoStore nvSRAM+RTC 3.3V 32Kx8 AutoStore nvSRAM+RTC 3.3V 32Kx8 AutoStore nvSRAM+RTC 3.3V 32Kx8 AutoStore nvSRAM+RTC Document Number: 001-52040 Rev. *A SSOP48-300 SSOP48-300 SSOP48-300 SSOP48-300 SSOP48-300 SSOP48-300 SSOP48-300 SSOP48-300 Access Times (ns) 25 45 25 45 25 45 25 45 Temperature Commercial Commercial Commercial Commercial Industrial Industrial Industrial Industrial Page 20 of 22 [+] Feedback STK17T88 Package Diagram Figure 16. 48-Pin SSOP (51-85061) 51-85061-*C Document Number: 001-52040 Rev. *A Page 21 of 22 [+] Feedback STK17T88 Document History Page Document Title: STK17T88 32K x 8 AutoStore™ nvSRAM with Real-Time Clock Document Number: 001- 52040 Rev ECN No. Orig. of Change Submission Date ** 2668660 GVCH/PYRS 03/04/2009 New data sheet *A 2675319 GVCH 03/17/2009 Corrected typo on page 1 in ‘Description’ section: changed 256KB to 256Kb. Description of change Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at cypress.com/sales. Products PSoC Solutions PSoC psoc.cypress.com Clocks & Buffers clocks.cypress.com General Low Power/Low Voltage psoc.cypress.com/solutions psoc.cypress.com/low-power Wireless wireless.cypress.com Precision Analog Memories memory.cypress.com LCD Drive psoc.cypress.com/lcd-drive image.cypress.com CAN 2.0b psoc.cypress.com/can USB psoc.cypress.com/usb Image Sensors psoc.cypress.com/precision-analog © Cypress Semiconductor Corporation, 2009. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document Number: 001-52040 Rev. *A Revised March 17, 2009 Page 22 of 22 AutoStore and QuantumTrap are registered trademarks of Cypress Semiconductor Corporation. All products and company names mentioned in this document may be the trademarks of their respective holders. [+] Feedback