STP7NK80Z - STP7NK80ZFP STB7NK80Z - STB7NK80Z-1 N-channel 800V - 1.5Ω - 5.2A - TO-220/TO-220FP/D2PAK/I2PAK Zener-protected SuperMESH™ Power MOSFET General features Type VDSS (@Tjmax) RDS(on) ID STP7NK80Z 800V < 1.8Ω 5.2A STP7NK80ZFP 800V < 1.8Ω 5.2A STB7NK80Z 800V < 1.8Ω 5.2A STB7NK80Z-1 800V < 1.8Ω 5.2A ■ Extremely high dv/dt capability ■ 100% avalange tested ■ Gate charge minimized ■ Very low intrinsic capacitances ■ Very good manufacturing repeatibility 3 1 2 TO-220FP TO-220 3 12 3 1 D2PAK I2PAK Internal schematic diagram Description The SuperMESH™ series is obtained through an extreme optimization of ST’s well established strip-based PowerMESH™ layout. In addition to pushing on-resistance significantly down, special care is taken to ensure a very good dv/dt capability for the most demanding applications. Such series complements ST full range of high voltage Power MOSFETs including revolutionary MDmesh™ products. Applications ■ Switching application Order codes Part number Marking Package Packaging STP7NK80Z P7NK80Z TO-220 Tube STP7NK80ZFP P7NK80ZFP TO-220FP Tube STB7NK80ZT4 B7NK80Z D²PAK Tape e reel STB7NK80Z-1 B7NK80Z-1 I²PAK Tube October 2006 Rev 5 1/18 www.st.com 18 Contents STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Contents 1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.1 Electrical characteristics (curves) ............................. 7 3 Test circuit 4 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5 Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2/18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 1 Electrical ratings Electrical ratings Table 1. Absolute maximum ratings Value Symbol Parameter TO-220 / D²PAK I²PAK VDS Drain-source voltage (VGS = 0) 800 VGS Gate- source voltage ± 30 IDM (2) PTOT A 3.3 3.3 (1) A Drain current (pulsed) 20.8 20.8(1) A Total dissipation at TC = 25°C 125 30 W 1 0.24 W/°C Derating factor 5.2 VESD(G-S) Gate source ESD(HBM-C=100pF, R=1.5KΩ) dv/dt (3) V 5.2 Drain current (continuous) at TC = 100°C ID V (1) Drain current (continuous) at TC = 25°C ID Unit TO-220FP 4000 V 4.5 V/ns Peak diode recovery voltage slope VISO Insulation withstand voltage (RMS) from all three leads to external heat sink (t=1s; Tc= 25°C) Tj Tstg Max operating junction temperature Storage temperature -- 2500 V °C °C -55 to 150 1. Limited only by maximum temperature allowed 2. Pulse width limited by safe operating area 3. ISD ≤5.2 A, di/dt ≤200A/µs, VDD ≤V(BR)DSS, Tj ≤TJMAX. Table 2. Thermal data Value Symbol Parameter TO-220/D2PAK I2PAK Unit TO-220FP Rthj-case Thermal resistance junction-case max Rthj-amb Thermal resistance junction-ambient max 62.5 °C/W Tl Maximum lead temperature for soldering purpose 300 °C 1 4.2 °C/W 3/18 Electrical ratings Table 3. Symbol 4/18 STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Avalanche characteristics Parameter Value Unit IAR Avalanche current, repetitive or not-repetitive (pulse width limited by Tj Max) 5.2 A EAS Single pulse avalanche energy (starting Tj=25°C, Id=Iar, Vdd=50V) 210 mJ STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 2 Electrical characteristics Electrical characteristics (TCASE=25°C unless otherwise specified) Table 4. On/off states Symbol Parameter V(BR)DSS Drain-source Breakdown voltage Test conditions ID =1MA, VGS = 0 Zero gate voltage Drain Current (VGS = 0) IGSS Gate-body leakage Current (VDS = 0) VGS = ± 20 V VGS(th) Gate threshold voltage VDS = VGS, ID = 100 µA RDS(on) Static drain-source on resistance VGS = 10 V, ID = 2.6 A Symbol gfs (1) Ciss Coss Crss Coss eq. (2) td(on) tr tr(off) tr Qg Qgs Qgd tr(Voff) tr tc Typ. Max. Unit 800 V VDS = Max rating IDSS Table 5. Min. 1 50 µA µA ± 10 µA 3.75 4.5 V 1.5 1.8 Ω Typ. Max. Unit VDS = Max rating, TC = 125°C 3 Dynamic Parameter Test conditions Forward transconductance VDS = 15v, ID = 2.6 A Input capacitance Output capacitance Reverse transfer capacitance Equivalent output capacitance Turn-on delay time Rise time Turn-off delay time Fall time VDS = 25 V, f = 1 MHz, VGS = 0 VDS =0V, VDS = 0V to 640V VDD = 400 V, ID = 2.6 A, RG = 4.7 Ω, VGS = 10 V (see Figure 16) Total gate charge Gate-source charge Gate-drain charge VDD = 640 V, ID = 5.2 A, Off-voltage rise time Fall time Cross-over time VDD = 640 V, ID = 5.2 A, VGS = 10 V (see Figure 17) RG = 4.7 Ω, VGS = 10 V (see Figure 16) Min. 5 S 1138 122 25 pF pF pF 50 pF 20 12 45 20 ns ns ns ns 40 7 21 12 10 20 56 nC nC nC ns ns ns 1. Pulsed: pulse duration=300µs, duty cycle 1.5% 2. Coss eq. is defined as a constant equivalent capacitance giving the same charging time as Coss when VDS increases from 0 to 80% VDSS. 5/18 Electrical characteristics Table 6. Symbol ISD STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Source drain diode Parameter ISDM(1) Source-drain current Source-drain current (pulsed) VSD(2) Forward on voltage trr Qrr IRRM Reverse recovery time Reverse recovery charge Reverse recovery current Test conditions Min. Typ. ISD = 5.2 A, VGS = 0 ISD = 5.2 A, di/dt = 100 A/µs VDD = 50 V, Tj = 150°C Max. Unit 5.2 20.8 A A 1.6 V 530 3.31 12.5 (see Figure 21) ns µC A 1. Pulsed: pulse duration=300µs, duty cycle 1.5% 2. Pulse width limited by safe operating area Table 7. Symbol Gate-source zener diode Parameter Test conditions BVGSO (1) Gate-source breakdown voltage Igs=± 1mA (Open Drain) Min. Typ. Max. Unit 30 1. The built-in back-to-back Zener diodes have specifically been designed to enhance not only the device’s ESD capability, but also to make them safely absorb possible voltage transients that may occasionally be applied from gate to source. In this respect the Zener voltage is appropriate to achieve an efficient and cost-effective intervention to protect the device’s integrity. These integrated Zener diodes thus avoid the usage of external components. 6/18 V STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Electrical characteristics 2.1 Electrical characteristics (curves) Figure 1. Safe operating area for TO-220/ D2PAK/I2PAK Figure 2. Thermal impedance for TO-220/ D2PAK/I2PAK Figure 3. Safe operating area for TO-220FP Figure 4. Thermal impedance for TO-220FP Figure 5. Output characterisics Figure 6. Transfer characteristics 7/18 Electrical characteristics STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Figure 7. Transconductance Figure 9. Gate charge vs gate-source voltage Figure 10. Capacitance variations Figure 11. Normalized gate threshold voltage vs temperature 8/18 Figure 8. Static drain-source on resistance Figure 12. Normalized on resistance vs temperature STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Figure 13. Source-drain diode forward characteristic Electrical characteristics Figure 14. Normalized BVDSS vs temperature Figure 15. Maximum avalanche energy vs temperature 9/18 Test circuit 3 STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Test circuit Figure 16. Switching times test circuit for resistive load Figure 17. Gate charge test circuit Figure 18. Test circuit for inductive load Figure 19. Unclamped Inductive load test switching and diode recovery times circuit Figure 20. Unclamped inductive waveform 10/18 Figure 21. Switching time waveform STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 4 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect . The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com 11/18 Package mechanical data STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 TO-220 MECHANICAL DATA DIM. mm. MIN. inch MAX. MIN. TYP. MAX. A 4.40 4.60 0.173 0.181 b 0.61 0.88 0.024 0.034 b1 1.15 1.70 0.045 0.066 c 0.49 0.70 0.019 0.027 D 15.25 15.75 0.60 0.620 E 10 10.40 0.393 0.409 e 2.40 2.70 0.094 0.106 e1 4.95 5.15 0.194 0.202 F 1.23 1.32 0.048 0.052 H1 6.20 6.60 0.244 0.256 J1 2.40 2.72 0.094 0.107 0.551 L 13 14 0.511 L1 3.50 3.93 0.137 L20 16.40 L30 12/18 TYP 0.154 0.645 28.90 1.137 øP 3.75 3.85 0.147 0.151 Q 2.65 2.95 0.104 0.116 STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Package mechanical data TO-220FP MECHANICAL DATA mm. DIM. MIN. A 4.4 inch TYP MAX. MIN. TYP. 4.6 0.173 0.181 MAX. 0.106 B 2.5 2.7 0.098 D 2.5 2.75 0.098 0.108 E 0.45 0.7 0.017 0.027 F 0.75 1 0.030 0.039 F1 1.15 1.7 0.045 0.067 F2 1.15 1.7 0.045 0.067 G 4.95 5.2 0.195 0.204 G1 2.4 2.7 0.094 0.106 H 10 10.4 0.393 0.409 L2 16 0.630 L3 28.6 30.6 1.126 1.204 L4 9.8 10.6 .0385 0.417 L5 2.9 3.6 0.114 0.141 L6 15.9 16.4 0.626 0.645 9 9.3 0.354 0.366 Ø 3 3.2 0.118 0.126 B D A E L7 L3 L6 F2 H G G1 F F1 L7 L2 L5 1 2 3 L4 13/18 Package mechanical data STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 D2PAK MECHANICAL DATA TO-247 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 4.4 4.6 0.173 0.181 A1 2.49 2.69 0.098 0.106 A2 0.03 0.23 0.001 0.009 B 0.7 0.93 0.027 0.036 B2 1.14 1.7 0.044 0.067 C 0.45 0.6 0.017 0.023 C2 1.23 1.36 0.048 0.053 D 8.95 9.35 0.352 0.368 10.4 0.393 D1 E 8 10 E1 0.315 8.5 0.334 G 4.88 5.28 0.192 0.208 L 15 15.85 0.590 0.625 L2 1.27 1.4 0.050 0.055 L3 1.4 1.75 0.055 0.068 M 2.4 3.2 0.094 R 0º 0.126 0.015 4º 3 V2 0.4 1 14/18 STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Package mechanical data TO-262 (I2PAK) MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 4.40 4.60 0.173 0.181 A1 2.40 2.72 0.094 0.107 b 0.61 0.88 0.024 0.034 b1 1.14 1.70 0.044 0.066 c 0.49 0.70 0.019 0.027 c2 1.23 1.32 0.048 0.052 D 8.95 9.35 0.352 0.368 e 2.40 2.70 0.094 0.106 e1 4.95 5.15 0.194 0.202 E 10 10.40 0.393 0.410 L 13 14 0.511 0.551 L1 3.50 3.93 0.137 0.154 L2 1.27 1.40 0.050 0.055 15/18 Packaging mechanical data 5 STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Packaging mechanical data D2PAK FOOTPRINT TAPE AND REEL SHIPMENT REEL MECHANICAL DATA DIM. mm MIN. A B 1.5 C 12.8 D 20.2 G 24.4 N 100 T TAPE MECHANICAL DATA DIM. mm MIN. MAX. MIN. A0 10.5 10.7 0.413 0.421 B0 15.7 15.9 0.618 0.626 D 1.5 1.6 0.059 0.063 D1 1.59 1.61 0.062 0.063 E 1.65 1.85 0.065 0.073 F 11.4 11.6 0.449 0.456 K0 4.8 5.0 0.189 0.197 P0 3.9 4.1 0.153 0.161 P1 11.9 12.1 0.468 0.476 P2 1.9 2.1 0.075 0.082 MAX. R 50 1.574 T 0.25 0.35 0.0098 0.0137 W 23.7 24.3 * on sales type 16/18 inch 0.933 0.956 inch MAX. MIN. MAX. 330 12.992 13.2 0.504 0.520 26.4 0.960 1.039 0.059 0795 3.937 30.4 1.197 BASE QTY BULK QTY 1000 1000 STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 6 Revision history Revision history Table 8. Revision history Date Revision Changes 09-Sep-2004 3 Complete version 16-Aug-2006 4 New template, no content change 09-Oct-2006 5 Corrected order code 17/18 STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 18/18