TCO series P Case Tantalum capacitors Chip tantalum capacitors TCO Series P Case zFeatures (P) zDimensions (Unit : mm) 1) Conductive polymer used for the Anode mark cathode material. 2) Ultra-low ESR. (1/10 compared with the conventional type) W L 3) Screening by thermal shock. H 1 W2 S S + − (Unit : mm) P case Dimensions L 2.0 + − 0.2 W1 1.25 + − 0.2 W2 0.9 + − 0.2 H 1.1 + − 0.1 S 0.45 + − 0.3 zPart No. Explanation Nominal capacitance in pF in 3 digits: 2 significant figures followed by the figure representing the number of 0's. Series name T C O Case style P Nominal capacitance 0 J Rated voltage Code Rated voltage (V) 0J 6.3 1A 10 1 0 6 M 8 R Capacitance tolerance Code Capacitance tolerance M +− 20% 8 : Tape width R : Positive electrode on the side opposite to sprocket hole Rev.C 1/8 TCO series P Case Tantalum capacitors zRated Table. Marking TCO Series! P Case Rated voltage (V.DC) μF 6.3 0J N 3.3 S 4.7 W 6.8 a 10 e 15 j 22 n 33 s 47 w 68 10 1A ∗P ∗P ∗ Under development z Marking The indications listed below should be given on the surface of a capacitor. (1) Polarity : The polarity should be shown by bar. (on the anode side) (2) Rated DC voltage : Due to the small size of P case, a voltage code is used as shown below. (3) Visual typical example (1) voltage code (2) capacitance code Rated DC Voltage (V) 2.5 Capacitance Code A Nominal Capacitance (μF) 1.0 g 4 E 1.5 j 6.3 J 2.2 A 10 N 3.3 S 4.7 W 6.8 a 10 e 15 j 22 Voltage Code e n 33 s 47 Voltage code Capacitance code P case (2012) ja Rev.C 2/8 TCO series P Case Tantalum capacitors zCharacteristics Item Operating Temperature Performance −55 C to +105 C Test conditions (based on JIS C 5101−1 and JIS C 5101−3) Voltage reduction when temperature exceeds+85 C Maximum operating +85 C temperature with no voltage derating Rated voltage (VDC) 6.3 10 at 85 C Category voltage (VDC) 5 Surge voltage (VDC) 8 13 at 85 C DC Leakage current 3μA or 0.1CV whichever is greater Shown in " Standard list " Rated voltage for 5min Capacitance tolerance + −20% Shall be satisfied allowance range. Tangent of loss angle (Df, tan δ) 8 at 105 C Measuring frequency : 120+ −12Hz Measuring voltage : 0.5Vrms +1.5 to 2V.DC Measuring circuit : DC Equivalent series circuit Shall be satisfied the voltage on " Standard list " Measuring frequency : 120 + −12Hz Measuring voltage : 0.5Vrms +1.5 to 2V.DC Measuring circuit : DC Equivalent series circuit Shall be satisfied the voltage on " Standard list " Measuring frequency : 100 + −10kHz Measuring voltage : 0.5Vrms or less ESR Resistance to Appearance There should be no significant abnormality. Soldering heat The indications should be clear. L.C. ΔC / C Less than 150% of initial limit Within + − 20% of initial value tan δ Less than 150% of initial limit Dip in the solder bath +5 C Solder temp : 240− Duration : 10+ −0.5s :1 Repetition After the specimens, leave it at room temperature for over 24h and then measure the sample. Rev.C 3/8 TCO series P Case Tantalum capacitors Item Temperature cycle Performance Appearance There should be no significant abnormality. L.C Less than 500% of initial limit ΔC / C Within+ −20% of intial value Df (tan δ) Less than 150% of initial limit Test conditions (based on JIS C 5101−1 and JIS C 5101−3) Repetition : 5 cycles (1 cycle : steps 1 to 4) without discontinuation. 1 2 3 4 Temp. −55+ −3 C Room temp. 105+ −2 C Room temp. Time 30+ −3min 3min.or less 30+ −3min 3min.or less After the specimens, leave it at room temperature for over 24h and then measure the sample. Moisture resistance Temperature Stebility Appearance There should be no significant abnormality. The indications should be L.C Less than 150% of initial limit ΔC / C +30% / −20% Df (tan δ) Less than 150% of initial limit Temp. −55 C ΔC / C Within 0/−20% of initial value Df (tan δ) Shall be satisfied the voltage on " Standard list " − L.C Surge voltage Temp. +105 C ΔC / C Within +50/0% of initial value Df (tan δ) Shall be satisfied the voltage on " Standard list " L.C Less than 1CV Appearance There should be no significant abnormality. L.C ΔC / C Df (tan δ) After leaving the sample under such atmospheric condition that the temperature and humidity are + 2 C and 90 to 95% RH,respectiveiy,for 500 − + 24h 40 − leave it at room temperature for over 24h and then measure the sample. Less than initial limit + 20% of initial value Within − Less than initial limit Apply the specified serge voltage every 5+ − 0.5 min. for 30+ −5 s. each time in the atmospheric condition of 85+ −2 C. Repeat this rocedure 1,000 times. After the specimens, leave it at room temperature for over 24h and then measure the sample. Rev.C 4/8 TCO series P Case Tantalum capacitors Item Performance Loading at Appearance There should be no significant High temperature abnormality. L.C Less than 200% of initial limit ΔC / C Within + − 20% of initial value Df (tan δ) 150% of initial limit less than Terminal strength Capacitance The measured value should be stable. Appearance There should no significant abnormality. Test conditions (based on JIS C 5101−1 and JIS C 5101−3) After applying the rated voltage for 1000+36 h without discontinuation via the serial resistance + 2 C, leave of 3Ω or less at a temperature of 85 − the sample at room temperature / humidity for over 24h and measure the value. A force is applied to the terminal until it bends to 1mm and by a perscribed tool maintain the condition for5s.(See the figure below) 20 50 (Unit : mm) F (Apply force) R230 1mm thickness=1.6mm 45 Adhesiveness The terminal should not come off. 45 Apply force of 5N in the two directions shown + 1s after mounting the in the figure below for 10 − terminal on a circuit board. product YAA C105 Apply force a circuit board Dimensions Refer to "External dimensions" Measure using a caliper of JISB 7507 Class 2 or higher grade. Resistance to solvents The indication should be clear Solderability 3/4 or more surface area of the solder coated terminal dipped in the soldering bath should be covered with the new solder. + 5s, at room Dip in the isopropyl alcohol for 30 − temperature. + 2.5mm / s Dip speed=25 − Pre−treatment(accelerated aging): Leave the sample on the boiling distilled water for 1 h. Solder temp. . : 245+ −5C : 3+ Duration − 0.5s : M705 Solder : Rosin25% Flux IPA75% Frequency : 10 to 55 to 10Hz/min. Amplitude : 1.5mm Time : 2h each in X and Y directions Mounting : The terminal is soldered on a print circuit board. Vibration Capacitance Measure value should not fluctuate during the measurement. Appearance There should no significant abnormality. Rev.C 5/8 TCO series P Case Tantalum capacitors zStandard list, TCO series < P case : 2012 size > Part No. Rated Voltage 85°C Category Voltage 105°C Surge Voltage 85°C Cap. 120Hz (V) (V) (V) (μF) 5 8 8 13 10 4.7 TCO P 0J 106 6.3 10 TCO P 1A 475 =Tolerance(M : ± 20%) Df ESR Tolerance Leakage 120Hz 100kHz Current (%) 25°C 1WV 5min 25°C 105°C (mΩ) −55°C (μA) (%) 85°C + − 20 + − 20 6.3 4.7 6 6 6 6 9 9 500 500 zPackaging specifications Reek [ P case ] 4.0± 0.1 4.0± 0.1 +1.0 9.0 0 Chip φ60 +1 0 B 11.4+ −1.0 φ13+ −0.2 3.5± 0.05 A t1 8.0± 0.2 0.1 0 φ1.5 t2 2.0± 0.05 0 φ180 −1.5 1.75± 0.1 Tape [ P case ] Feeding direction Unit : [mm] Case A+ −0.1 B+ −0.1 t1 + − 0.05 t2 + − 0.1 P 1.55 2.3 0.25 1.5 Pull direction Labelsticling position EIAJ ET−7200B compatible zPackaging style Case code package P Taping Packaging style plastic taping Symbol Basic ordering units φ180mmReel R 3,000pcs z Damp proof package One reel is packed in aluminum bag. The size of aluminum bag is 240(g) x 250(b)mm. The size up to 230(c)mm is to zipper. A desiccant is packed with a reel. The aluminum bag is heat-sealed. The label of the same as the label on the reel is placed om the aluminum bag. b C a Rev.C 6/8 TCO series P Case Tantalum capacitors LEAKAGE CURRENT RATIO DCL / DCL z Electrical characteristics and operation notes (1) Leakage current-to-voltage ratio 1 0.1 0.01 0 20 40 60 80 100 % OF RATED VOLTAGE (VR) Fig.1 (2) Derating voltage as function of temperature 100 105°C PERCENT OF 85°C RVDC1 (VR) 85°C 90 Rated Voltage Surge Voltage Category Voltage (V.DC) (V.DC) (V.DC) 6.3 8 5 10 13 8 80 70 60 50 75 85 95 105 TEMPERATURE (°C) Fig.2 (3) Reliability The malfunction rate of tantalum solid state electrolytic capacitors varies considerably depending on the conditions of usage (ambient temperature, applied voltage, circuit resistance). Formula for calculating malfunction rate Op = Ob u (SE u SSR u SQ u SCV) Op Ob SE SSR SQ SCV : Malfunction rate stemming from operation : Basic malfunction rate : Environmental factors : Series resistance : Level of malfunction rate : Capacitance For details on how to calculate the malfunction rate stemming from operation, see the tantalum solid state electrolytic capacitors column in MIL-HDBK-217. Rev.C 7/8 TCO series P Case Tantalum capacitors (4) Impedance frequency characteristics 1000 (5) ESR frequency characteristics 10000 TCOP0J106M P case 6.3V10μF TCOP0J106M P case 6.3V10μF 1000 100 ESR (Ω) CAPACITANCE (μF) 100 10 10 1 1 0.1 0.1 0.01 0.1 1 10 100 1000 0.01 0.01 0.1 1 10 100 FREQUENCY (kHz) FREQUENCY (kHz) Fig.3 Fig.4 (6) Capacitance temperature characteristics 120Hz 1000 (7) ESR temperature characteristics 100kHz 1 30 TCOP0J106M P case 6.3V10μF TCOP0J106M P case 6.3V10μF 10 ESR (Ω) CAP CHANGE (%) 20 0 0.1 −10 −20 −30 −55 −15 25 65 105 0.01 −55 −15 25 65 TEMPERATURE ( C) TEMPERATURE ( C) Fig.5 Fig.6 105 Rev.C 8/8 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office. ROHM Customer Support System www.rohm.com Copyright © 2007 ROHM CO.,LTD. THE AMERICAS / EUPOPE / ASIA / JAPAN Contact us : webmaster@ rohm.co. jp 21, Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121 FAX : +81-75-315-0172 Appendix1-Rev2.0