TI TL16C750FN

TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
D
D
D
D
D
D
D
D
D
D
D
D
D
Pin-to-Pin Compatible With the Existing
TL16C550B/C
Programmable 16- or 64-Byte FIFOs to
Reduce CPU Interrupts
Programmable Auto-RTS and Auto-CTS
In Auto-CTS Mode, CTS Controls
Transmitter
In Auto-RTS Mode, Receiver FIFO Contents
and Threshold Control RTS
Serial and Modem Control Outputs Drive a
RJ11 Cable Directly When Equipment Is on
the Same Power Drop
Capable of Running With All Existing
TL16C450 Software
After Reset, All Registers Are Identical to
the TL16C450 Register Set
Up to 16-MHz Clock Rate for Up to 1-Mbaud
Operation
In the TL16C450 Mode, Hold and Shift
Registers Eliminate the Need for Precise
Synchronization Between the CPU and
Serial Data
Programmable Baud Rate Generator Allows
Division of Any Input Reference Clock by 1
to (216 – 1) and Generates an Internal 16 ×
Clock
Standard Asynchronous Communication
Bits (Start, Stop, and Parity) Added or
Deleted to or From the Serial Data Stream
5-V and 3-V Operation
D
D
D
D
D
D
D
D
D
D
D
D
D
Register Selectable Sleep Mode and
Low-Power Mode
Independent Receiver Clock Input
Independently Controlled Transmit,
Receive, Line Status, and Data Set
Interrupts
Fully Programmable Serial Interface
Characteristics:
– 5-, 6-, 7-, or 8-Bit Characters
– Even-, Odd-, or No-Parity Bit Generation
and Detection
– 1-, 1 1/2-, or 2-Stop Bit Generation
– Baud Generation (DC to 1 Mbits Per
Second)
False Start Bit Detection
Complete Status Reporting Capabilities
3-State Output CMOS Drive Capabilities for
Bidirectional Data Bus and Control Bus
Line Break Generation and Detection
Internal Diagnostic Capabilities:
– Loopback Controls for Communications
Link Fault Isolation
– Break, Parity, Overrun, Framing Error
Simulation
Fully Prioritized Interrupt System Controls
Modem Control Functions (CTS, RTS, DSR,
DTR, RI, and DCD)
Available in 44-Pin PLCC and 64-Pin SQFP
Industrial Temperature Range Available for
64-Pin SQFP
description
The TL16C750 is a functional upgrade of the TL16C550C asynchronous communications element (ACE),
which in turn is a functional upgrade of the TL16C450. Functionally equivalent to the TL16C450 on power up
(character or TL16C450 mode), the TL16C750, like the TL16C550C, can be placed in an alternate mode (FIFO
mode). This relieves the CPU of excessive software overhead by buffering received and transmitted characters.
The receiver and transmitter FIFOs store up to 64 bytes including three additional bits of error status per byte
for the receiver FIFO. The user can choose between a 16-byte FIFO mode or an extended 64-byte FIFO mode.
In the FIFO mode, there is a selectable autoflow control feature that can significantly reduce software overload
and increase system efficiency by automatically controlling serial data flow through the RTS output and the CTS
input signals (see Figure 1).
The TL16C750 performs serial-to-parallel conversion on data received from a peripheral device or modem and
parallel-to-serial conversion on data received from its CPU. The CPU can read the ACE status at any time. The
ACE includes complete modem control capability and a processor interrupt system that can be tailored to
minimize software management of the communications link.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  1997, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
description (continued)
The TL16C750 ACE includes a programmable baud rate generator capable of dividing a reference clock by
divisors from 1 to (216 – 1) and producing a 16 × reference clock for the internal transmitter logic. Provisions are
also included to use this 16 × clock for the receiver logic. The ACE accommodates a 1-Mbaud serial rate
(16-MHz input clock) so a bit time is 1 µs and a typical character time is 10 µs (start bit, 8 data bits, stop bit).
Two of the TL16C450 terminal functions have been changed to TXRDY and RXRDY, which provide signaling
to a direct memory access (DMA) controller.
D4
D3
D2
D1
D0
NC
VCC
RI
DCD
DSR
CTS
FN PACKAGE
(TOP VIEW)
6 5 4 3 2 1 44 43 42 41 40
7
39
8
38
9
37
10
36
11
35
12
34
13
33
14
32
15
31
16
30
17
29
18 19 20 21 22 23 24 25 26 27 28
MR
OUT1
DTR
RTS
OUT2
NC
INTRPT
RXRDY
A0
A1
A2
XIN
XOUT
WR1
WR2
VSS
NC
RD1
RD2
DDIS
TXRDY
ADS
D5
D6
D7
RCLK
SIN
NC
SOUT
CS0
CS1
CS2
BAUDOUT
1
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
48
2
47
3
46
4
45
5
44
6
43
7
42
8
41
9
40
10
39
11
38
12
37
13
36
14
35
15
34
33
16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
A2
A1
NC
A0
RXRDY
NC
INTRPT
NC
OUT2
RTS
NC
DTR
NC
OUT1
NC
MR
XIN
XOUT
NC
WR1
NC
WR2
NC
VSS
RD1
RD2
NC
DDIS
TXRDY
NC
ADS
NC
D6
D5
NC
BAUDOUT
NC
CS2
CS1
NC
CS0
SOUT
NC
NC
SIN
RCLK
NC
D7
PM PACKAGE
(TOP VIEW)
NC – No internal connection
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
D4
NC
D3
D2
NC
D1
D0
NC
VCC
NC
RI
NC
DCD
DSR
NC
CTS
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
functional block diagram
Internal
Data Bus
9–2
D(7 – 0)
8
Data
Bus
Buffer
S
e
l
e
c
t
Receiver
FIFO
8
Receiver
Shift
Register
Receiver
Buffer
Register
A1
A2
CS0
CS1
CS2
ADS
MR
RD1
RD2
WR1
WR2
DDIS
TXRDY
XIN
SIN
10
Receiver
Timing and
Control
Line
Control
Register
A0
11
RCLK
36
RTS
31
30
29
Divisor
Latch (LS)
14
Divisor
Latch (MS)
Baud
Generator
17
15
16
28
39
24
25
Transmitter
Timing and
Control
Line
Status
Register
Select
and
Control
Logic
Transmitter
FIFO
Transmitter
Holding
Register
20
21
8
S
e
l
e
c
t
8
Transmitter
Shift
Register
BAUDOUT
Autoflow
Control
Enable
(AFE)
13
SOUT
26
Modem
Control
Register
27
18
8
40
37
XOUT 19
32
RXRDY
Modem
Status
Register
8
Modem
Control
Logic
41
42
43
VCC 44
22
VSS
38
Power
Supply
Interrupt
Enable
Register
Interrupt
Identification
Register
8
Interrupt
Control
Logic
CTS
DTR
DSR
DCD
RI
OUT1
35
OUT2
33 INTRPT
8
FIFO
Control
Register
NOTE A: Terminal numbers shown are for the FN package.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
Terminal Functions
TERMINAL
NO.
FN
NO.
PM
I/O
DESCRIPTION
A0
A1
A2
31
30
29
20
18
17
I
Register select. A0 – A2 are used during read and write operations to select the ACE register to read from
or write to. Refer to Table 1 for register addresses and ADS signal description.
ADS
28
15
I
Address strobe. When ADS is active (low), the register select signals (A0, A1, and A2) and chip select signals
(CS0, CS1, CS2) drive the internal select logic directly; when ADS is high, the register select and chip select
signals are held at the logic levels they were in when the low-to-high transition of ADS occurred.
BAUDOUT
17
64
O
Baud out. BAUDOUT is a 16 × clock signal for the transmitter section of the ACE. The clock rate is established
by the reference oscillator frequency divided by a divisor specified by the baud generator divisor latches.
BAUDOUT can also be used for the receiver section by tying this output to RCLK.
CS0
CS1
CS2
14
15
16
59
61
62
I
Chip select. When CS0 and CS1 are high and CS2 is low, the ACE is selected. When any of these inputs
are inactive, the ACE remains inactive. Refer to the ADS signal description.
CTS
40
33
I
Clear to send. CTS is a modem status signal. Its condition can be checked by reading bit 4 (CTS) of the
modem status register. Bit 0 (∆CTS) of the modem status register indicates that CTS has changed states
since the last read from the modem status register. When the modem status interrupt is enabled, CTS
changes states, and the auto-CTS mode is not enabled, an interrupt is generated. CTS is also used in the
auto-CTS mode to control the transmitter.
D0
D1
D2
D3
D4
D5
D6
D7
2
3
4
5
6
7
8
9
42
43
45
46
48
50
51
52
I/O
Data bus. Eight data lines with 3-state outputs provide a bidirectional path for data, control, and status
information between the ACE and the CPU. As inputs, they use fail safe CMOS compatible input buffers.
DCD
42
36
I
Data carrier detect. DCD is a modem status signal. Its condition can be checked by reading bit 7 (DCD) of
the modem status register. Bit 3 (∆DCD) of the modem status register indicates that DCD has changed states
since the last read from the modem status register. When the modem status interrupt is enabled and DCD
changes state, an interrupt is generated.
DDIS
26
12
O
Driver disable. DDIS is active (high) when the CPU is not reading data. When active, DDIS can disable an
external transceiver.
DSR
41
35
I
Data set ready. DSR is a modem status signal. Its condition can be checked by reading bit 5 (DSR) of the
modem status register. Bit 1 (∆DSR) of the modem status register indicates DSR has changed states since
the last read from the modem status register. When the modem status interrupt is enabled and the DSR
changes states, an interrupt is generated.
DTR
37
28
O
Data terminal ready. When active (low), DTR informs a modem or data set that the ACE is ready to establish
communication. DTR is placed in the active state by setting the DTR bit of the modem control register to one.
DTR is placed in the inactive condition either as a result of a master reset, during loop mode operation, or
clearing the DTR bit.
INTRPT
33
23
O
Interrupt. When active (high), INTRPT informs the CPU that the ACE has an interrupt to be serviced. Four
conditions that cause an interrupt to be issued are: a receiver error, received data that is available or timed
out (FIFO mode only), an empty transmitter holding register, or an enabled modem status interrupt. INTRPT
is reset (deactivated) either when the interrupt is serviced or as a result of a master reset.
MR
39
32
I
Master reset. When active (high), MR clears most ACE registers and sets the levels of various output signals
(refer to Table 2).
OUT1
OUT2
38
35
30
25
O
Outputs 1 and 2. These are user-designated output terminals that are set to their active (low) level by setting
their respective modem control register (MCR) bits (OUT1 and OUT2). OUT1 and OUT2 are set to their
inactive (high) level as a result of master reset, during loop mode operations, or by clearing bit 2 (OUT1) or
bit 3 (OUT2) of the MCR.
RCLK
10
54
I
Receiver clock. RCLK is the 16× baud rate clock for the receiver section of the ACE.
NAME
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
Terminal Functions (Continued)
TERMINAL
NO.
FN
NO.
PM
I/O
DESCRIPTION
RD1
RD2
24
25
9
10
I
Read inputs. When either RD1 or RD2 is active (low or high respectively) while the ACE is selected, the CPU
is allowed to read status information or data from a selected ACE register. Only one of these inputs is required
for the transfer of data during a read operation; the other input should be tied in its inactive state (i.e., RD2 tied
low or RD1 tied high).
RI
43
38
I
Ring indicator. RI is a modem status signal. Its condition can be checked by reading bit 6 (RI) of the modem
status register. Bit 2 (TERI) of the modem status register indicates that RI has transitioned from a low to a high
level since the last read from the modem status register. If the modem status interrupt is enabled when this
transition occurs, an interrupt is generated.
RTS
36
26
O
Request to send. When active, RTS informs the modem or data set that the ACE is ready to receive data. RTS
is set to its active level by setting the RTS MCR bit and is set to its inactive (high) level either as a result of a
master reset, during loop mode operations, or by clearing bit 1 (RTS) of the MCR. In the auto-RTS mode, RTS
is set to its inactive level by the receiver threshold control logic.
RXRDY
32
21
O
Receiver ready. Receiver direct memory access (DMA) signalling is available with RXRDY. When operating
in the FIFO mode, one of two types of DMA signalling can be selected through the FIFO control register bit
3 (FCR3). When operating in the TL16C450 mode, only DMA mode 0 is allowed. Mode 0 supports
single-transfer DMA in which a transfer is made between CPU bus cycles. Mode 1 supports multitransfer DMA
in which multiple transfers are made continuously until the receiver FIFO has been emptied. In DMA mode 0
(FCR0 = 0 or FCR0 = 1, FCR3 = 0), when there is at least one character in the receiver FIFO or receiver holding
register, RXRDY is active (low). When RXRDY has been active but there are no characters in the FIFO or
holding register, RXRDY goes inactive (high). In DMA mode 1 (FCR0 = 1, FCR3 = 1), when the trigger level
or the timeout has been reached, RXRDY goes active (low); when it has been active but there are no more
characters in the FIFO or holding register, it goes inactive (high).
SIN
11
55
I
Serial data. SIN is the input from a connected communications device.
SOUT
13
58
O
Composite serial data output to a connected communication device. SOUT is set to the marking (high) level
as a result of master reset.
TXRDY
27
13
O
Transmitter ready. Transmitter DMA signalling is available with TXRDY. When operating in the FIFO mode,
one of two types of DMA signalling can be selected through FCR3. When operating in the TL16C450 mode,
only DMA mode 0 is allowed. Mode 0 supports single-transfer DMA in which a transfer is made between CPU
bus cycles. Mode 1 supports multitransfer DMA in which multiple transfers are made continuously until the
transmit FIFO has been filled.
VCC
VSS
44
40
22
8
WR1
WR2
20
21
4
6
I
XIN
XOUT
18
19
1
2
I/O
NAME
5-V supply voltage
Supply common
Write inputs. When either input is active (low or high respectively) and while the ACE is selected, the CPU is
allowed to write control words or data into a selected ACE register. Only one of these inputs is required to
transfer data during a write operation; the other input should be tied in its inactive state (i.e., WR2 tied low or
WR1 tied high).
External clock. XIN and XOUT connect the ACE to the main timing reference (clock or crystal).
detailed description
autoflow control
Auto-flow control is composed of auto-CTS and auto-RTS. With auto-CTS, CTS must be active before the
transmit FIFO can emit data (see Figure 1). With auto-RTS, RTS becomes active when the receiver is empty
or the threshold has not been reached. When RTS is connected to CTS, data transmission does not occur
unless the receive FIFO has empty space. Thus, overrun errors are eliminated when ACE1 and ACE2 are
TLC16C750s with enabled autoflow control. If not, overrun errors occur if the transmit data rate exceeds the
receive FIFO read latency.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
autoflow control (continued)
ACE1
ACE2
Serial to
Parallel
RCV
FIFO
Flow
Control
SIN
SOUT
CTS
RTS
Parallel
to Serial
XMT
FIFO
Flow
Control
D7– D0
D7– D0
Parallel
to Serial
XMT
FIFO
Flow
Control
SOUT
SIN
RTS
CTS
Serial to
Parallel
RCV
FIFO
Flow
Control
Figure 1. Autoflow Control (auto-RTS and auto-CTS) Example
auto-RTS (see Figure 1)
Auto-RTS data flow control originates in the receiver timing and control block (see functional block diagram)
and is linked to the programmed receiver FIFO trigger level. When the receiver FIFO level reaches a trigger level
of 1, 4, 8, or 14 in 16-byte mode or 1, 16, 32, or 56 in 64-byte mode, RTS is deasserted. The sending ACE may
send an additional byte after the trigger level is reached (assuming the sending ACE has another byte to send)
because it may not recognize the deassertion of RTS until after it has begun sending the additional byte. RTS
is automatically reasserted once the receiver FIFO is emptied by reading the receiver buffer register. The
reassertion signals the sending ACE to continue transmitting data.
auto-CTS (see Figure 1)
The transmitter circuitry checks CTS before sending the next data byte. When CTS is active, the transmitter
sends the next byte. To stop the transmitter from sending the following byte, CTS must be released before the
middle of the last stop bit that is currently being sent. The auto-CTS function reduces interrupts to the host
system. When flow control is enabled, the CTS state changes and does not trigger host interrupts because the
device automatically controls its own transmitter. Without auto-CTS, the transmitter sends any data present in
the transmit FIFO and a receiver overrun error can result.
enabling auto-RTS and auto-CTS
The auto-RTS and auto-CTS modes of operation are activated by setting bit 5 of the modem control register
(MCR) to 1 (see Figure 2).
SOUT
Start
Bits 0 – 7
Stop
Start
Bits 0 – 7 Stop
Start
Bits 0 – 7 Stop
CTS
NOTES: A. When CTS is low, the transmitter keeps sending serial data out.
B. When CTS goes high before the middle of the last stop bit of the current byte, the transmitter finishes sending the current byte but
it does not send the next byte.
C. When CTS goes from high to low, the transmitter begins sending data again.
Figure 2. CTS Functional Timing
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
enabling auto-RTS and auto-CTS (continued)
The receiver FIFO trigger level can be set to 1, 4, 8, or 14 bytes for the 16-byte mode and 1, 16, 32, or 56 bytes
for 64-byte mode (see Figure 3).
SIN
Start
Byte N
Stop
Start
Byte N+1
Start
Stop
Byte
Stop
RTS
RD
(RD RBR)
1
2
N
N+1
NOTES: A. N = receiver FIFO trigger level
B. The two blocks in dashed lines cover the case where an additional byte is sent as described in auto-RTS.
Figure 3. RTS Functional Timing, Receiver FIFO Trigger Level
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 6 V
Input voltage range, VI: Standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to VCC + 0.5 V
Fail safe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 6.5 V
Output voltage range, VO: Standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to VCC + 0.5 V
Fail safe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 6.5 V
Input clamp current, IIK (VI < 0 or VI > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 20 mA
Output clamp current, IOK (VO < 0 or VO > VCC) (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 20 mA
Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
Operating free-air temperature range, TA (TL16C750I) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 85°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. This applies for external input and bidirectional buffers. VI > VCC does not apply to fail safe terminals.
2. This applies for external output and bidirectional buffers. VO > VCC does not apply to fail safe terminals.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
recommended operating conditions
low voltage (3.3 V nominal)
MIN
NOM
MAX
Supply voltage, VCC
3
3.3
3.6
V
Input voltage, VI
0
VCC
V
High-level input voltage, VIH (see Note 3)
0.7 VCC
V
Low-level input voltage, VIL (see Note 3)
Output voltage, VO (see Note 4)
UNIT
0
High-level output current, IOH (all outputs)
Low-level output current, IOL (all outputs)
Input capacitance, cI
0.3 VCC
V
VCC
1.8
V
mA
3.2
mA
1
pF
Operating free-air temperature, TA
0
25
70
°C
Junction temperature range, TJ (see Note 5)
0
25
115
°C
14
MHz
Oscillator/clock speed
NOTES: 3. Meets TTL levels, VIHmin = 2 V and VILmax = 0.8 V on nonhysteresis inputs
4. Applies for external output buffers
5. These junction temperatures reflect simulated conditions. Absolute maximum junction temperature is 150°C. The customer is
responsible for verifying junction temperature.
standard voltage (5 V nominal)
Supply voltage, VCC
Input voltage, VI
MIN
NOM
4.75
5
0
High-level input voltage, VIH
MAX
UNIT
5.25
V
VCC
V
0.7 VCC
V
Low-level input voltage, VIL
0.2 VCC
V
VCC
4
V
mA
Low-level output current, IOL (all outputs)
4
mA
Input capacitance, cI
1
pF
Output voltage, VO (see Note 4)
0
High-level output current, IOH (all outputs)
Operating free-air temperature, TA
0
25
70
°C
Junction temperature range, TJ (see Note 5)
0
25
115
°C
16
MHz
Oscillator/clock speed
NOTES: 4. Applies for external output buffers
5. These junction temperatures reflect simulated conditions. Absolute maximum junction temperature is 150°C. The customer is
responsible for verifying junction temperature.
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
electrical characteristics over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted)
low voltage (3.3 V nominal)
VOH
VOL
IOZ
IIL
PARAMETER
High-level output voltage†
TEST CONDITIONS
IOH = – 1.8 mA
IOL = 3.2 mA
Low-level output voltage†
High-impedance 3-state output current (see Note 6)
Low-level input current (see Note 7)
MIN
MAX
VCC – 0.55
VI = VCC or GND
VI = GND
IIH
High-level input current (see Note 8)
VI = VCC
† For all outputs except XOUT
NOTES: 6. The 3-state or open-drain output must be in the high-impedance state.
7. Specifications only apply with pullup termination turned off.
8. Specifications only apply with pulldown termination turned off.
UNIT
V
0.5
V
± 10
µA
–1
µA
1
µA
standard voltage (5 V nominal)
VOH
VOL
IOZ
IIL
PARAMETER
High-level output voltage†
TEST CONDITIONS
IOH = – 4 mA
IOL = 4 mA
Low-level output voltage†
High-impedance 3-state output current (see Note 6)
Low-level input current (see Note 7)
VI = VCC or GND
VI = GND
IIH
High-level input current (see Note 8)
VI = VCC
† For all outputs except XOUT
NOTES: 6. The 3-state or open-drain output must be in the high-impedance state.
7. Specifications only apply with pullup termination turned off.
8. Specifications only apply with pulldown termination turned off.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MIN
MAX
VCC – 0.8
UNIT
V
0.5
V
± 10
µA
–1
µA
1
µA
9
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
system timing requirements over recommended ranges of supply voltage and operating free-air
temperature
PARAMETER
ALT. SYMBOL
FIGURE
TEST CONDITIONS
tcR
tcW
Cycle time, read (tw7 + td8 + td9)
RC
Cycle time, write (tw6 + td5 + td6)
WC
tw1
tw2
Pulse duration, clock (XIN) high
tXH
tXL
4
f = 16 MHz maximum
4
f = 16 MHz maximum
tw5
tw6
Pulse duration, ADS low
tADS
tWR
tw7
tw8
Pulse duration, read strobe
tsu1
tsu2
Setup time, address valid before ADS↑
tRD
tMR
tAS
tsu3
tsu4†
Setup time, data valid before WR1↓ or WR2↑
th1
th2
Hold time, address low after ADS↑
th3
th4†
Hold time, CS valid after WR1↑ or WR2↓
th5
th6
th7†
Hold time, data valid after WR1↑ or WR2↓
td4†
td5
td6†
Delay time, CS valid before WR1↓ or WR2↑
td7†
td8†
Delay time, CS valid to RD1↓ or RD2↑
td9
td10
Delay time, read cycle, RD1↑ or RD2↓ to ADS↓
Pulse duration, clock (XIN) low
Pulse duration, write strobe
Pulse duration, MR
Setup time, CS valid before ADS↑
tCS
tDS
Setup time, CTS↑ before midpoint of stop bit
Hold time, CS valid after ADS↑
Hold time, address valid after WR1↑ or WR2↓
Hold time, CS valid after RD1↑ or RD2↓
Hold time, address valid after RD1↑ or RD2↓
Delay time, address valid before WR1↓ or WR2↑
Delay time, write cycle, WR1↑ or WR2↓ to ADS↓
Delay time, address valid to RD1↓ or RD2↑
Delay time, RD1↓ or RD2↑ to data valid
td11
Delay time, RD1↑ or RD2↓ to floating data
† Only applies when ADS is low
MIN
MAX
UNIT
87
ns
87
ns
25
ns
25
ns
5, 6
9
ns
5
40
ns
6
40
ns
1
µs
8
ns
5, 6
8
ns
5
15
5, 6
16
ns
10
ns
tAH
tCH
5, 6
0
ns
5, 6
0
ns
tWCS
tWA
5
10
ns
5
10
ns
tDH
5
5
ns
tRCS
tRA
6
10
ns
6
20
ns
tCSW
tAW
5
7
ns
5
7
ns
tWC
tCSR
5
40
ns
6
7
ns
tAR
tRC
6
7
ns
40
ns
tRVD
tHZ
6
CL = 75 pF
45
ns
6
CL = 75 pF
20
ns
6
system switching characteristics over recommended ranges of supply voltage and operating
free-air temperature (see Note 9)
PARAMETER
tdis(R)
Disable time, RD1↓↑ or RD2↑↓ to DDIS↑↓
ALT. SYMBOL
FIGURE
TEST CONDITIONS
tRDD
6
CL = 75 pF
MIN
MAX
20
UNIT
ns
NOTE 9: Charge and discharge times are determined by VOL, VOH, and external loading.
baud generator switching characteristics over recommended ranges of supply voltage and
operating free-air temperature, CL = 75 pF
PARAMETER
tw3
tw4
Pulse duration, BAUDOUT low
td1
td2
Delay time, XIN↑ to BAUDOUT↑
10
Pulse duration, BAUDOUT high
Delay time, XIN↑↓ to BAUDOUT↓
ALT. SYMBOL
FIGURE
TEST CONDITIONS
MIN
tLW
tHW
4
f = 16 MHz, CLK ÷ 2
50
ns
4
f = 16 MHz, CLK ÷ 2
50
ns
tBLD
tBHD
4
45
ns
4
45
ns
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MAX
UNIT
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
commercial maximum switching characteristics, VCC = 4.75 V, TJ = 115°C
PARAMETER
tPLH
tPHL
INTRINSIC
DELAY
(ns)
DELTA
DELAY
(ns/pF)
CL = 15 pF
CL = 50 pF
CL = 85 pF
CL = 100 pF
– 0.92
0.571
7.65
27.66
47.66
56.23
– 0.79
0.312
3.89
14.83
25.76
30.45
Output rise time, XO
10.86
40.42
69.98
82.65
Output fall time, XO
5.47
20.90
36.34
42.95
FROM
(INPUT)
TO
(OUTPUT)
XIN
XO
tr
tf
DELAY (ns)
commercial maximum switching characteristics, VCC = 3 V, TJ = 115°C
PARAMETER
tPLH
tPHL
INTRINSIC
DELAY
(ns)
DELTA
DELAY
(ns/pF)
CL = 15 pF
CL = 50 pF
CL = 85 pF
CL = 100 pF
– 4.69
1.017
10.57
46.16
81.75
97.00
– 3.05
0.442
3.58
19.04
34.51
41.13
Output rise time, XO
14.39
64.87
115.35
136.98
Output fall time, XO
5.06
26.53
48.01
57.21
FROM
(INPUT)
TO
(OUTPUT)
XIN
XO
tr
tf
DELAY (ns)
receiver switching characteristics over recommended ranges of supply voltage and operating
free-air temperature (see Note 10)
PARAMETER
ALT. SYMBOL
FIGURE
td12
Delay time, RCLK to sample clock
tSCD
7
TEST CONDITIONS
MIN
10
ns
td13
Delay time, stop to set receiver error interrupt or read RBR to LSI interrupt or stop to
RXRDY↓
tSINT
7, 8, 9,
10, 11
2
RCLK
cycle
td14
Delay time, read RBR/LSR low to reset
interrupt low
tRINT
7, 8, 9,
10, 11
CL = 75 pF
MAX
120
UNIT
ns
NOTE 10: In the FIFO mode, the read cycle (RC) = 425 ns (minimum) between reads of the receive FIFO and the status registers (interrupt
identification register or line status register).
transmitter switching characteristics over recommended ranges of supply voltage and operating
free-air temperature
PARAMETER†
ALT. SYMBOL
FIGURE
TEST CONDITIONS
MIN
MAX
UNIT
td15
Delay time, INTRPT to transmit start
tIRS
12
8
24
baudout
cycles
td16
Delay time, start to interrupt
tSTI
12
8
10
baudout
cycles
td17
Delay time, WR THR to reset interrupt
tHR
12
CL = 75 pF
ns
34
baudout
cycles
ns
td18
Delay time, initial write to interrupt (THRE)
tSI
12
td19
td20
Delay time, read IIR to reset interrupt (THRE)
tIR
12
CL = 75 pF
70
tWXI
13, 14
CL = 75 pF
75
ns
9
baudout
cycles
td21
Delay time, write to TXRDY inactive
Delay time, start to TXRDY active
tSXA
13, 14
16
50
CL = 75 pF
† THRE = transmitter holding register empty, IIR = interrupt identification register.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
modem control switching characteristics over recommended ranges of supply voltage and
operating free-air temperature, CL = 75 pF
PARAMETER
ALT. SYMBOL
FIGURE
15
60
ns
Delay time, modem interrupt to set interrupt
tMDO
tSIM
15
35
ns
Delay time, RD MSR to reset interrupt
tRIM
15
45
ns
td22
td23
Delay time, WR MCR to output
td24
MIN
MAX
UNIT
td25
Delay time, CTS low to SOUT↓
16
24
baudout
cycles
td26
Delay time, receiver threshold byte to RTS↑
17
2
baudout
cycles
td27
Delay time, read of last byte in receive FIFO to RTS↓
17
3
baudout
cycles
PARAMETER MEASUREMENT INFORMATION
N
tw1
tw2
XIN
td2
td1
BAUDOUT
(1/1)
td1
td2
BAUDOUT
(1/2)
tw3
tw4
BAUDOUT
(1/3)
BAUDOUT
(1/N)
(N > 3)
2 XIN Cycles
(N – 2) XIN Cycles
Figure 4. Baud Generator Timing Waveforms
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
PARAMETER MEASUREMENT INFORMATION
tw5
50%
ADS
50%
50%
tsu1
th1
A0 – A2
50%
50% Valid †
Valid
50%
tsu2
th2
CS0, CS1, CS2
50%
th3
tw6
td4
td5
WR1, WR2
Valid †
Valid
50%
th4†
td6
50%
Active
50%
tsu3
th5
Valid Data
D7 – D0
† Applicable only when ADS is low
Figure 5. Write Cycle Timing Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
PARAMETER MEASUREMENT INFORMATION
tw5
50%
ADS
50%
50%
tsu1
th1
A0 – A2
Valid
50%
50% Valid† 50%
tsu2
th2
CS0, CS1, CS2
50%
Valid
td7†
td8†
RD1, RD2
50%
50% Valid†
th6
tw7
th7†
td9
Active
50%
tdis(R)
DDIS
50%
tdis(R)
50%
50%
td10
td11
Valid Data
D7 – D0
† Applicable only when ADS is low
Figure 6. Read Cycle Timing Waveforms
14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
PARAMETER MEASUREMENT INFORMATION
RCLK
td12
8 Clocks
Sample Clock
TL16C450 Mode:
SIN
Start
Data Bits 5 – 8
Parity
Stop
Sample Clock
INTRPT
(data ready)
50%
td13
INTRPT
(receiver error)
50%
td14
50%
50%
RD1, RD2
(read RBR)
50%
RD1, RD2
(read LSR)
50%
Active
Active
td14
Figure 7. Receiver Timing Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
PARAMETER MEASUREMENT INFORMATION
SIN
Data Bits 5 – 8
Stop
Sample Clock
Trigger Level
INTRPT
(FCR6, 7 = 0, 0)
50%
(FIFO at or above
trigger level)
50%
(FIFO below
trigger level)
td13
(see Note A)
td14
Line Status
INTRPT
(LSI)
50%
50%
td14
RD1
(RD LSR)
Active
50%
Active
RD1
(RD RBR)
50%
NOTE A: For a time-out interrupt, td13 = 9 RCLKs.
Figure 8. Receive FIFO First Byte (Sets DR Bit) Waveforms
SIN
Stop
Sample Clock
Time-Out or
Trigger Level
INTRPT
50%
50%
(FIFO below
trigger level)
td13
(see Note A)
td14
50%
Line Status
INTRPT (LSI)
50%
Top Byte of FIFO
td13
td14
RD1, RD2
(RD LSR)
RD1, RD2
(RD RBR)
(FIFO at or above
trigger level)
50%
Active
50%
50%
Active
Previous Byte
Read From FIFO
NOTE A: For a time-out interrupt, td13 = 9 RCLKs.
Figure 9. Receive FIFO Bytes Other Than the First Byte (DR Internal Bit Already Set) Waveforms
16
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
PARAMETER MEASUREMENT INFORMATION
RD
(RD RBR)
50%
Active
See Note A
SIN
(first byte)
Stop
Sample Clock
td13
(see Note B)
RXRDY
td14
50%
50%
NOTES: A. This is the reading of the last byte in the FIFO.
B. For a time-out interrupt, td13 = 9 RCLKs.
Figure 10. Receiver Ready (RXRDY) Waveforms, FCR0 = 0 or FCR0 = 1 and FCR3 = 0 (Mode 0)
RD
(RD RBR)
50%
Active
See Note A
SIN
(first byte that reaches
the trigger level)
Sample Clock
td13
(see Note B)
RXRDY
td14
50%
50%
NOTES: A. This is the reading of the last byte in the FIFO.
B. For a time-out interrupt, td13 = 9 RCLKs.
Figure 11. Receiver Ready (RXRDY) Waveforms, FCR0 = 1 and FCR3 = 1 (Mode 1)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
PARAMETER MEASUREMENT INFORMATION
Start
50%
SOUT
Data Bits
Parity
td15
INTRPT
(THRE)
Start
50%
Stop
td16
50%
50%
50%
50%
50%
td18
td17
td17
WR THR 50%
50%
50%
td19
RD IIR
50%
Figure 12. Transmitter Timing Waveforms
WR
(WR THR)
SOUT
Byte #1
50%
Data
Parity
Stop
Start
50%
td21
td20
TXRDY
50%
50%
Figure 13. Transmitter Ready (TXRDY) Waveforms, FCR0 = 0 or FCR0 = 1 and FCR3 = 0 (Mode 0)
Byte #16
WR
(WR THR)
SOUT
50%
Data
Parity
Stop
td21
td20
TXRDY
Start
50%
50%
FIFO Full
50%
Figure 14. Transmitter Ready (TXRDY) Waveforms, FCR0 = 1 and FCR3 = 1 (Mode 1)
18
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
PARAMETER MEASUREMENT INFORMATION
WR
(WR MCR)
50%
50%
td22
td22
RTS, DTR,
OUT1, OUT2
50%
50%
50%
CTS, DSR, DCD
td23
INTRPT
(modem)
50%
50%
50%
td24
td23
RD2
(RD MSR)
50%
RI
50%
Figure 15. Modem Control Timing Waveforms
tsu4
CTS
50%
50%
td25
SOUT
50%
Midpoint of Stop Bit
Figure 16. CTS and SOUT Autoflow Control Timing (Start and Stop) Waveforms
Midpoint of Stop Bit
SIN
td26
RTS
td27
50%
50%
50%
RBRRD
Figure 17. Auto-RTS Timing for Receiver Threshold at All Trigger Levels Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
19
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
PARAMETER MEASUREMENT INFORMATION
SOUT
D7 – D0
D7 – D0
MEMR or I/OR
MEMW or I/ON
INTR
C
P
U
B
U
S
RESET
A0
RD1
RTS
WR1
DTR
INTRPT
DSR
MR
DCD
A0
A1
A1
A2
SIN
EIA
232-D Drivers
and Receivers
CTS
TL16C750
(ACE)
RI
A2
ADS
XIN
WR2
L
3.072 MHz
RD2
CS
H
CS2
XOUT
CS1
BAUDOUT
CS0
RCLK
Figure 18. Basic TL16C750 Configuration
APPLICATION INFORMATION
Receiver Disable
WR
WR1
TL16C750
(ACE)
Microcomputer
System
Data Bus
Data Bus
8-Bit
Bus Transceiver
D7 – D0
DDIS
Driver Disable
Figure 19. Typical Interface for a High-Capacity Data Bus
20
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
APPLICATION INFORMATION
TL16C750
XIN
A16 – A23
A16 – A23
XOUT
18
Alternate
Crystal Control
19
17
14
BAUDOUT
CS0
Address
Decoder
CPU
15
16
RCLK
CS1
CS2
DTR
28
ADS
RTS
36
1
OUT2
35
A0 – A2
AD0 – AD7
D0 – D2
Buffer
43
RI
42
PHI1
20
OUT1
MR
AD0 – AD15
37
38
ADS
39
RSI/ABT
10
DCD
PHI2
8
41
6
DSR
CTS
PHI1
ADS
PHI2
RSTO
RD
24
TCU
20
WR
RD1
40
5
13
SOUT
2
WR1
11
SIN
INTRPT
3
33
27
AD0 – AD15
TXRDY
25
21
RD2
DDIS
WR2
GND
(VSS)
RXRDY
22
26
32
44
7
1
EIA-232-D
Connector
5V
(VCC)
NOTE A: Terminal numbers shown are for the FN package.
Figure 20. Typical TL16C750 Connection to a CPU
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
21
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
PRINCIPLES OF OPERATION
Table 1. Register Selection
DLAB†
A2
A1
A0
0
L
L
L
Receiver buffer (read), transmitter holding register (write)
0
L
L
H
Interrupt enable register
X
L
H
L
Interrupt identification register (read only)
X
L
H
L
FIFO control register (write)
X
L
H
H
Line control register
X
H
L
L
Modem control register
X
H
L
H
Line status register
X
H
H
L
Modem status register
X
H
H
H
Scratch register
1
L
L
L
Divisor latch (LSB)
REGISTER
1
L
L
H
Divisor latch (MSB)
† The divisor latch access bit (DLAB) is the most significant bit of the line control register. The DLAB signal
is controlled by writing to this bit location (see Table 3).
Table 2. ACE Reset Functions
REGISTER/SIGNAL
RESET
CONTROL
RESET STATE
Interrupt Enable Register
Master Reset
All bits cleared (0 – 5 forced and 6 – 7 permanent)
Interrupt Identification Register
Master Reset
Bit 0 is set, bits 1 – 4 are cleared, and bits 5 – 7 are cleared
FIFO Control Register
Master Reset
All bits cleared
Line Control Register
Master Reset
All bits cleared
Modem Control Register
Master Reset
All bits cleared (6 – 7 permanent)
Line Status Register
Master Reset
Bits 5 and 6 are set, all other bits are cleared
Modem Status Register
Master Reset
Bits 0 – 3 are cleared, bits 4 – 7 are input signals
SOUT
Master Reset
High
INTRPT (receiver error flag)
Read LSR/MR
Low
INTRPT (received data available)
Read RBR/MR
Low
Read IR/Write THR/MR
Low
Read MSR/MR
Low
OUT2
Master Reset
High
RTS
Master Reset
High
DTR
Master Reset
High
OUT1
Master Reset
High
Scratch Register
Master Reset
No effect
Divisor Latch (LSB and MSB) Registers
Master Reset
No effect
Receiver Buffer Registers
Master Reset
No effect
Transmitter Holding Registers
Master Reset
No effect
INTRPT (transmitter holding register empty)
INTRPT (modem status changes)
Receiver FIFO
MR/FCR1 – FCR0/
∆FCR0
All bits cleared
XMIT FIFO
MR/FCR2 – FCR0/
∆FCR0
All bits cleared
22
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
PRINCIPLES OF OPERATION
accessible registers
The system programmer, through the CPU, has access to and control over any of the ACE registers. These
registers control ACE operations, receive data, and transmit data. Descriptions of these registers follow in
Table 3.
Table 3. Summary of Accessible Registers
REGISTER ADDRESS
Bit
No.
0
1
2
3
0 DLAB = 0
0 DLAB = 0
Receiver
Buffer
Register
(Read
Only)
Transmitter
Holding
Register
(Write
Only)
RBR
Data Bit 0†
Data Bit 1
Data Bit 2
Data Bit 3
1 DLAB = 0
2
2
3
4
5
6
7
0 DLAB = 1
1 DLAB = 1
Interrupt
Enable
Register
Interrupt
Ident.
Register
(Read
Only)
FIFO
Control
Register
(Write
Only)
Line
Control
Register
Modem
Control
Register
Line
Status
Register
Modem
Status
Register
Scratch
Register
Divisor
Latch
(LSB)
Latch
(MSB)
THR
IER
IIR
FCR
LCR
MCR
LSR
MSR
SCR
DLL
DLM
Data Bit 0
Enable
Received
Data
Available
Interrupt
(ERBI)
0 when
interrupt
Pending
FIFO
Enable
Word
Length
Select
Bit 0
(WLS0)
Data
Terminal
Ready
(DTR)
Data
Ready
(DR)
Delta
Clear
to Send
Bit 0
Bit 0
Bit 8
Enable
Transmitter
Holding
Register
Empty
Interrupt
(ETBEI)
Interrupt
ID
Bit 1
Receiver
FIFO
Reset
Word
Length
Select
Bit 1
(WLS1)
Request
to Send
(RTS)
Overrun
Error
(OE)
Bit 1
Bit 1
Bit 9
Data Bit 2
Enable
Receiver
Line Status
Interrupt
(ELSI)
Interrupt
ID
Bit 2
Transmitter
FIFO
Reset
Number
of
Stop Bits
(STB)
OUT1
Parity
Error
(PE)
Trailing
Edge Ring
Indicator
(TERI)
Bit 2
Bit 2
Bit 10
Data Bit 3
Enable
Modem
Status
Interrupt
(EDSSI)
Interrupt
ID
Bit 2
(see
Note 4)
DMA
Mode
Select
Parity
Enable
(PEN)
OUT2
Framing
Error
(FE)
Delta
Data
Carrier
Detect
Bit 3
Bit 3
Bit 11
Loop
Break
Interrupt
(BI)
Clear
to
Send
(CTS)
Bit 4
Bit 4
Bit 12
Data Bit 1
(∆CTS)
Delta
Data
Set
Ready
(∆DSR)
(∆DCD)
4
Data Bit 4
Data Bit 4
Sleep Mode
Enable
0
Reserved
Even
Parity
Select
(EPS)
5
Data Bit 5
Data Bit 5
Low Power
Mode Enable
64 Byte
FIFO
Enabled
64 Byte
FIFO
Enable‡
Stick
Parity
Flow
Control
Enable
(AFE)
Transmitter
Holding
Register
(THRE)
Data
Set
Ready
(DSR)
Bit 5
Bit 5
Bit 13
6
Data Bit 6
Data Bit 6
0
FIFOs
Enabled
(see
Note 11)
Receiver
Trigger
(LSB)
Break
Control
0
Transmitter
Empty
(TEMT)
Ring
Indicator
(RI)
Bit 6
Bit 6
Bit 14
7
Data Bit 7
Data Bit 7
0
FIFOs
Enabled
(see
Note 11)
Receiver
Trigger
(MSB)
Divisor
Latch
Access
Bit
(DLAB)‡
0
Error in
Receiver
FIFO
(see
Note 12)
Data
Carrier
Detect
(DCD)
Bit 7
Bit 7
Bit 15
† Bit 0 is the least significant bit. It is the first bit serially transmitted or received.
‡ Access to DLAB LSB, MSB, and FCR bit 5 require LCR bit 7 = 1
NOTE 11: These bits are always 0 in the TL16C450 mode.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
23
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
PRINCIPLES OF OPERATION
FIFO control register (FCR)
The FCR is a write-only register at the same location as the IIR, which is a read-only register. The FCR enables
the FIFOs, clears the FIFOs, sets the receiver FIFO trigger level, and selects the type of DMA signaling.
D
D
D
D
D
D
D
Bit 0: FCR0 when set enables the transmit and receive FIFOs. This bit must be set when other FCR bits
are written to or they are not programmed. Changing this bit clears the FIFOs.
Bit 1: FCR1 when set clears all bytes in the receiver FIFO and resets its counter. The RSR is not cleared.
The logic 1 that is written to this bit position is self clearing.
Bit 2: FCR2 when set clears all bytes in the transmit FIFO and resets its counter to 0. The TSR is not
cleared. The logic 1 that is written to this bit position is self clearing.
Bit 3: When FCR0 is set, setting FCR3 causes the RXRDY and TXRDY to change from mode 0 to
mode 1.
Bit 4: Reserved for future use.
Bit 5: When this bit is set 64-byte mode of operation is selected. When cleared, the 16-byte mode is
selected. A write to FCR bit 5 is protected by setting the line control register (LCR) bit 7 = 1. LCR bit 7 needs
to cleared for normal operation.
Bits 6 and 7: FCR6 and FCR7 set the trigger level for the receiver FIFO interrupt (see Table 4).
Table 4. Receiver FIFO Trigger Level
BIT 7
BIT 6
16-BYTE RECEIVER FIFO
TRIGGER LEVEL (BYTES)
64-BYTE RECEIVER FIFO
TRIGGER LEVEL (BYTES)
0
0
01
01
0
1
04
16
1
0
08
32
1
1
14
56
FIFO interrupt mode operation
When the receiver FIFO and receiver interrupts are enabled (FCR0 = 1, IER0 = 1, IER2 = 1), a receiver interrupt
occurs as follows:
1. The received data available interrupt is issued to the microprocessor when the FIFO has reached its
programmed trigger level. It is cleared when the FIFO drops below its programmed trigger level.
2. The IIR receive data available indication also occurs when the FIFO trigger level is reached, and as the
interrupt, is cleared when the FIFO drops below the trigger level.
3. The receiver line status interrupt (IIR = 06 or 0110h) has higher priority than the received data available (IIR
= 04) interrupt.
4. The data ready bit (LSR0) is set when a character is transferred from the shift register to the receiver FIFO.
It is cleared when the FIFO is empty.
When the receiver FIFO and receiver interrupts are enabled:
24
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
PRINCIPLES OF OPERATION
FIFO interrupt mode operation (continued)
1. FIFO time-out interrupt occurs when the following conditions exist:
a. At least one character is in the FIFO.
b. The most recent serial character was received more than four continuous character times ago (if two
stop bits are programmed, the second one is included in this time delay).
c.
The most recent microprocessor read of the FIFO occurred more than four continuous character times
ago. This causes a maximum character received to interrupt an issued delay of 160 ms at
300 baud with a 12-bit character.
2. Character times are calculated by using RCLK for a clock signal (makes the delay proportional to the baud
rate).
3. When a time-out interrupt has occurred, the FIFO interrupt is cleared. The timer is reset when the
microprocessor reads one character from the receiver FIFO. When a time-out interrupt has not occurred,
the time-out timer is reset after a new character is received or after the microprocessor reads the receiver
FIFO.
When the transmitter FIFO and THRE interrupt are enabled (FCR0 = 1, IER1 = 1), transmit interrupts occur as
follows:
1. The transmitter holding register interrupt [IIR (3 –0) = 2] occurs when the transmit FIFO is empty. The
transmit FIFO is cleared [IIR (3 –0) = 1] when the THR is written to (1 to 16 characters may be written to
the transmit FIFO while servicing this interrupt) or the IIR is read.
2. The transmit FIFO empty indicator (LSR5 (THRE) = 1) is delayed one character time minus the last stop
bit time when there have not been at least two bytes in the transmit FIFO at the same time since the last
time that THRE = 1. The first transmitter interrupt after changing FCR0 is immediate when it is enabled.
Character time-out and receiver FIFO trigger level interrupts have the same priority as the current received data
available interrupt; transmit FIFO empty has the same priority as the current THRE interrupt.
FIFO polled mode operation
With FCR0 = 1 (transmitter and receiver FIFOs enabled), clearing IER0, IER1, IER2, IER3, or all four to 0 puts
the ACE in the FIFO polled mode of operation. Since the receiver and transmitter are controlled separately,
either one or both can be in the polled mode of operation.
In this mode, the user program checks receiver and transmitter status using the LSR. As stated previously:
•
•
•
•
•
LSR0 is set when there is at least one byte in the receiver FIFO.
LSR (1 – 4) specify which error(s) have occurred. Character error status is handled the same way as
when in the interrupt mode; the IIR is not affected since IER2 = 0.
LSR5 indicates when the THR is empty.
LSR6 indicates that both the THR and TSR are empty.
LSR7 indicates whether there are any errors in the receiver FIFO.
There is no trigger level reached or time-out condition indicated in the FIFO polled mode. However, the receiver
and transmitter FIFOs are still fully capable of holding characters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
25
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
PRINCIPLES OF OPERATION
interrupt enable register (IER)
The IER enables each of the five types of interrupts (refer to Table 5) and the INTRPT signal in response to an
interrupt generation. The IER can also disable the interrupt system by clearing bits 0 through 3. The contents
of this register are summarized in Table3 and are described in the following bulleted list.
D
D
D
D
D
D
D
Bit 0: When set, this bit enables the received data available interrupt.
Bit 1: When set, this bit enables the THRE interrupt.
Bit 2: When set, this bit enables the receiver line status interrupt.
Bit 3: When set, this bit enables the modem status interrupt.
Bit 4: When set, this bit enables sleep mode. The ACE is always awake when there is a byte in the
transmitter, activity on the SIN, or when the device is in the loopback mode. The ACE is also awake when
either ∆CTS, ∆DSR, ∆DCD, or TERI = 1. Bit 4 must be set to enable sleep mode.
Bit 5: When set, this bit enables low-power mode. Low-power mode functions similar to sleep mode.
However, this feature powers down the clock to the ACE only, while keeping the oscillator running. Bit 5 must
be set to enable low-power mode.
Bits 6 and 7: Not used (always cleared)
interrupt identification register (IIR)
The ACE has an on-chip interrupt generation and prioritization capability that permits a flexible interface with
most popular microprocessors.
The ACE provides four prioritized levels of interrupts:
D
D
D
D
Priority 1 – Receiver line status (highest priority)
Priority 2 – Receiver data ready or receiver character timeout
Priority 3 – Transmitter holding register empty
Priority 4 – Modem status (lowest priority)
When an interrupt is generated, the IIR indicates that an interrupt is pending and provides the type of interrupt
in its three least significant bits (bits 0, 1, and 2). The contents of this register are summarized in Table 3 and
described in Table 5. Details on each bit are as follows:
D
D
D
D
D
26
Bit 0: This bit can be used either in a hardwire prioritized, or polled interrupt system. When this bit is cleared,
an interrupt is pending. When bit 0 is set, no interrupt is pending.
Bits 1 and 2: Used to identify the highest priority interrupt pending as indicated in Table 3.
Bit 3: This bit is always cleared in the TL16C450 mode. In FIFO mode, this bit is set with bit 2 to indicate
that a time-out interrupt is pending.
Bit 4: Not used (always cleared)
Bits 5, 6, and 7: These bits are to verify the FIFO operation. When all 3 bits are cleared, TL16C450 mode
is chosen. When bits 6 and 7 are set and bit 5 is cleared, 16-byte mode is chosen. When bits 5, 6, and 7
are set, 64-byte mode is chosen.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
PRINCIPLES OF OPERATION
interrupt identification register (IIR) (continued)
Table 5. Interrupt Control Functions
INTERRUPT
IDENTIFICATION
REGISTER
BIT 3
BIT 2
BIT 1
BIT 0
0
0
0
1
PRIORITY
LEVEL
INTERRUPT TYPE
None
None
INTERRUPT SOURCE
INTERRUPT RESET
METHOD
None
None
0
1
1
0
1
Receiver line status
Overrun error, parity error,
framing error or break interrupt
0
1
0
0
2
Received data available
Receiver data available in the
TL16C450 mode or trigger level
reached in the FIFO mode.
Reading the receiver buffer
register
Reading the receiver buffer
register
Reading the line status register
1
1
0
0
2
Character time-out
indication
No characters have been
removed from or input to the
receiver FIFO during the last
four character times, and there
is at least one character in it
during this time
0
0
1
0
3
Transmitter holding
register empty
Transmitter holding register
empty
Reading the interrupt
identification register (if source
of interrupt) or writing into the
transmitter holding register
0
0
0
0
4
Modem status
Clear to send, data set ready,
ring indicator, or data carrier
detect
Reading the modem status
register
line control register (LCR)
The system programmer controls the format of the asynchronous data communication exchange through the
LCR. In addition, the programmer is able to retrieve, inspect, and modify the contents of the LCR; this eliminates
the need for separate storage of the line characteristics in system memory. The contents of this register are
summarized in Table 3 and described in the following bulleted list.
D
Bits 0 and 1: These two bits specify the number of bits in each transmitted or received serial character.
These bits are encoded as shown in Table 6.
Table 6. Serial Character Word Length
D
BIT 1
BIT 0
WORD LENGTH
0
0
5 bits
0
1
6 bits
1
0
7 bits
1
1
8 bits
Bit 2: This bit specifies either one, one and one-half, or two stop bits in each transmitted character. When
bit 2 is cleared, one stop bit is generated in the data. When bit 2 is set, the number of stop bits generated
is dependent on the word length selected with bits 0 and 1. The receiver clocks only the first stop bit,
regardless of the number of stop bits selected. The number of stop bits generated, in relation to word length
and bit 2, is shown in Table 7.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
27
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
PRINCIPLES OF OPERATION
line control register (LCR) (continued)
Table 7. Number of Stop Bits Generated
D
D
D
D
D
BIT 2
WORD LENGTH SELECTED
BY BITS 1 AND 2
NUMBER OF STOP
BITS GENERATED
0
Any word length
1
1
5 bits
1 1/2
1
6 bits
2
1
7 bits
2
1
8 bits
2
Bit 3: This bit is the parity enable bit. When bit 3 is set, a parity bit is generated in data transmitted between
the last data word bit and the first stop bit. In received data, when bit 3 is set, parity is checked. When bit
3 is cleared, no parity is generated or checked.
Bit 4: This bit is the even parity select bit. When parity is enabled (bit 3 is set) and bit 4 is set, even parity
(an even number of logic 1s in the data and parity bits) is selected. When parity is enabled and bit 4 is
cleared, odd parity (an odd number of logic 1s) is selected.
Bit 5: This is the stick parity bit. When bits 3, 4, and 5 are set, the parity bit is transmitted and checked as
cleared. When bits 3 and 5 are set and bit 4 is cleared, the parity bit is transmitted and checked as set. When
bit 5 is cleared, stick parity is disabled.
Bit 6: This bit is the break control bit. Bit 6 is set to force a break condition; i.e., a condition where SOUT
is forced to the spacing (low) state. When bit 6 is cleared, the break condition is disabled and has no affect
on the transmitter logic; it only affects the serial output.
Bit 7: This bit is the divisor latch access bit (DLAB). Bit 7 must be set to access the divisor latches of the
baud generator during a read or write or access bit 5 of the FCR. Bit 7 must be cleared during a read or write
to access the receiver buffer, the THR, or the IER.
line status register (LSR)†
The LSR provides information to the CPU concerning the status of data transfers. The contents of this register
are described in the following bulleted list and summarized in Table 3.
D
Bit 0: This bit is the data ready (DR) indicator for the receiver. DR is set when a complete incoming character
is received and transferred into the RBR or the FIFO. DR is cleared by reading all of the data in the RBR
or the FIFO.
D
Bit 1‡: This bit is the overrun error (OE) indicator. When OE is set, it indicates that before the character in
the RBR was read, it was overwritten by the next character transferred into the register. OE is cleared every
time the CPU reads the contents of the LSR. When the FIFO mode data continues to fill the FIFO beyond
the trigger level, an OE occurs only after the FIFO is full and the next character has been completely
received in the shift register. An OE is indicated to the CPU as soon as it happens. The character in the shift
register is overwritten, but it is not transferred to the FIFO.
D
Bit 2‡: This bit is the parity error (PE) indicator. When PE is set, it indicates that the parity of the received
data character does not match the parity selected in the LCR (bit 4). PE is cleared every time the CPU reads
the contents of the LSR. In the FIFO mode, PE is associated with the particular character in the FIFO to
which it applies. PE is revealed to the CPU when its associated character is at the top of the FIFO.
† The line status register is intended for read operations only; writing to this register is not recommended outside of a factory testing environment.
‡ Bits 1 through 4 are the error conditions that produce a receiver line status interrupt.
28
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
PRINCIPLES OF OPERATION
line status register (LSR)† (continued)
D
D
D
D
D
Bit 3‡: This bit is the framing error (FE) indicator. When FE is set, it indicates that the received character
does not have a valid (set) stop bit. FE is cleared every time the CPU reads the contents of the LSR. In the
FIFO mode, this error is associated with the particular character in the FIFO to which it applies. FE is
revealed to the CPU when its associated character is at the top of the FIFO. The ACE tries to resynchronize
after a FE. To accomplish this, it is assumed that the FE is due to the next start bit. The ACE samples this
start bit twice and then accepts the input data.
Bit 4: This bit is the break interrupt (BI) indicator. When BI is set, it indicates that the received data input
was held in the low state for longer than a full-word transmission time. A full-word transmission time is
defined as the total time to transmit the start, data, parity, and stop bits. BI is cleared every time the CPU
reads the contents of the LSR. In the FIFO mode, BI is associated with the particular character in the FIFO
to which it applies. BI is revealed to the CPU when its associated character is at the top of the FIFO. When
a break occurs, only one 0 character is loaded into the FIFO. The next character transfer is enabled after
SIN goes to the marking state for at least two RCLK samples and then receives the next valid start bit.
Bit 5: This bit is the transmitter holding register empty (THRE) indicator. THRE is set when the THR is
empty, indicating that the ACE is ready to accept a new character. If the THRE interrupt is enabled when
THRE is set, an interrupt is generated. THRE is set when the contents of the THR are transferred to the
TSR. THRE is cleared concurrent with the loading of the THR by the CPU. In the FIFO mode, THRE is set
when the transmit FIFO is empty; it is cleared when at least one byte is written to the transmit FIFO.
Bit 6: This bit is the transmitter empty (TEMT) indicator. TEMT bit is set when the THR and the TSR are
both empty. When either the THR or the TSR contains a data character, TEMT is cleared. In the FIFO mode,
TEMT is set when the transmitter FIFO and TSR are both empty.
Bit 7: In TL16C750 mode and in TL16C450 mode, this bit is always cleared. In the FIFO mode, LSR7 is
set when there is at least one parity, framing, or break error in the FIFO. It is cleared when the
microprocessor reads the LSR and there are no subsequent errors in the FIFO.
modem control register (MCR)
The MCR is an 8-bit register that controls an interface with a modem, data set, or peripheral device that is
emulating a modem. The contents of this register are summarized in Table 3 and are described in the following
bulleted list.
D
D
D
D
Bit 0: This bit (DTR) controls the DTR output.
Bit 1: This bit (RTS) controls RTS output.
Bit 2: This bit (OUT1) controls OUT1 signal.
Bit 3: This bit (OUT2) controls the OUT2 signal.
When any of bits 0 through 3 is set, the associated output is forced low; a cleared bit forces the associated output
high.
† The line status register is intended for read operations only; writing to this register is not recommended outside of a factory testing environment.
‡ Bits 1 through 4 are the error conditions that produce a receiver line status interrupt.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
29
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
PRINCIPLES OF OPERATION
modem control register (MCR) (continued)
D
D
Bit 4: This bit (LOOP) provides a local loop back feature for diagnostic testing of the ACE. When LOOP
is set, the following occurs:
–
SOUT is asserted high.
–
SIN is disconnected.
–
The output of the TSR is looped back into the RSR input.
–
The four modem control inputs (CTS, DSR, DCD, and RI) are disconnected.
–
The four modem control outputs (DTR, RTS, OUT1, and OUT2) are internally connected to the four
modem control inputs.
–
The four modem control outputs are forced to their inactive (high) states.
Bit 5: This bit (AFE) is the autoflow control enable. When bit 5 is set, the autoflow control, as described in
the detailed description, is enabled.
In the diagnostic mode, data that is transmitted is immediately received. This allows the processor to verify
the transmit and receive data paths to the ACE. The receiver and transmitter interrupts are fully operational.
The modem control interrupts are also operational, but the modem control interrupt sources are now the
lower four bits of the MCR instead of the four modem control inputs. All interrupts are still controlled by the
IER.
The ACE flow can be configured by programming bits 1 and 5 of the MCR as shown in Table 8.
Table 8. ACE Flow Configuration
MCR BIT 5
(AFE)
MCR BIT 1
(RTS)
ACE FLOW CONFIGURATION
1
1
Auto-RTS and auto-CTS enabled (autoflow control enabled)
1
0
Auto-CTS only enabled
0
X
Auto-RTS and auto-CTS disabled
When bit 5 of the FCR is cleared, there is a 16-byte AFC. When bit 5 of the FCR is set, there is a 64-byte AFC.
modem status register (MSR)
The MSR is an 8-bit register that provides information about the current state of the control lines from the
modem, data set, or peripheral device to the CPU. Additionally, four bits of this register provide change
information. When a control input from the modem changes state, the appropriate bit is set. All four bits are
cleared when the CPU reads the MSR. The contents of this register are summarized in Table 3 and are
described in the following bulleted list.
30
D
Bit 0: This bit is the change in clear-to-send (∆ CTS) indicator. ∆ CTS indicates that CTS has changed states
since the last time it was read by the CPU. When ∆ CTS is set (autoflow control is not enabled and the
modem status interrupt is enabled), a modem status interrupt is generated. When autoflow control is
enabled, no interrupt is generated. When ∆CTS is set, sleep or low-power modes are avoided.
D
Bit 1: This bit is the change in data set ready (∆ DSR) indicator. ∆ DSR indicates that DSR has changed
states since the last time it was read by the CPU. When ∆ DSR is set and the modem status interrupt is
enabled, a modem status interrupt is generated. When ∆DSR is set, the sleep or low-power modes are
avoided.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
PRINCIPLES OF OPERATION
modem status register (MSR) (continued)
D
D
D
D
D
D
Bit 2: This bit is the trailing edge of the ring indicator (TERI) detector. TERI indicates that RI to the chip has
changed from a low to a high level. When TERI is set and the modem status interrupt is enabled, a modem
status interrupt is generated. When TERI is set, sleep or low-power modes are avoided.
Bit 3: This bit is the change in data carrier detect (∆ DCD) indicator. ∆ DCD indicates that DCD to the chip
has changed states since the last time it was read by the CPU. When ∆ DCD is set and the modem status
interrupt is enabled, a modem status interrupt is generated. When ∆DCD is set, sleep or low-power modes
are avoided.
Bit 4: This bit is the complement of CTS. When the ACE is in the diagnostic test mode (LOOP
[MCR4] = 1), this bit is equal to the MCR bit 1 (RTS).
Bit 5: This bit is the complement of DSR input. When the ACE is in the diagnostic test mode (LOOP
[MCR4] = 1), this bit is equal to the MCR bit 0 (DTR).
Bit 6: This bit is the complement of RI. When the ACE is in the diagnostic test mode (LOOP [MCR4] = 1),
this bit is equal to the MCR bit 2 (OUT1).
Bit 7: This bit is the complement of DCD. When the ACE is in the diagnostic test mode (LOOP
[MCR4] = 1), this bit is equal to the MCR bit 3 (OUT2).
programmable baud generator
The ACE contains a programmable baud generator that takes a clock input in the range between dc and 16 MHz
and divides it by a divisor in the range between 1 and (216 –1). The output frequency of the baud generator is
16 × the baud rate. The formula for the divisor is:
divisor = XIN frequency input ÷ (desired baud rate × 16)
Two 8-bit registers, called divisor latches, store the divisor in a 16-bit binary format. These divisor latches must
be loaded during initialization of the ACE to ensure desired operation of the baud generator. When either of the
divisor latches is loaded, a 16-bit baud counter is also loaded to prevent long counts on initial load.
Tables 9 and 10 illustrate the use of the baud generator with crystal frequencies of 1.8432 MHz and 3.072 MHz
respectively. For baud rates of 38.4 kbits/s and below, the error obtained is very small. The accuracy of the
selected baud rate is dependent on the selected crystal frequency (see Figure 21).
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
31
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
PRINCIPLES OF OPERATION
programmable baud generator (continued)
Table 9. Baud Rates Using a 1.8432-MHz Crystal
DESIRED
BAUD RATE
DIVISOR USED
TO GENERATE
16 × CLOCK
PERCENT ERROR
DIFFERENCE BETWEEN
DESIRED AND ACTUAL
50
2304
75
1536
110
1047
0.026
134.5
857
0.058
150
768
300
384
600
192
1200
96
1800
64
2000
58
2400
48
3600
32
4800
24
7200
16
9600
12
19200
6
38400
3
56000
2
0.69
2.86
Table 10. Baud Rates Using a 3.072-MHz Crystal
DESIRED
BAUD RATE
32
DIVISOR USED
TO GENERATE
16 × CLOCK
50
3840
PERCENT ERROR
DIFFERENCE BETWEEN
DESIRED AND ACTUAL
75
2560
110
1745
0.026
134.5
1428
0.034
150
1280
300
640
600
320
1200
160
1800
107
2000
96
2400
80
3600
53
4800
40
7200
27
9600
20
19200
10
38400
5
POST OFFICE BOX 655303
0.312
0.628
1.23
• DALLAS, TEXAS 75265
TL16C750
ASYNCHRONOUS COMMUNICATIONS ELEMENT
WITH 64-BYTE FIFOs AND AUTOFLOW CONTROL
SLLS191C – JANUARY 1995 – REVISED DECEMBER 1997
PRINCIPLES OF OPERATION
programmable baud generator (continued)
VCC
VCC
Driver
XIN
XIN
External
Clock
C1
Crystal
RP
Optional
Driver
Optional
Clock
Output
RX2
Oscillator Clock
to Baud Generator
Logic
XOUT
Oscillator Clock
to Baud Generator
Logic
XOUT
C2
TYPICAL CRYSTAL/ OSCILLATOR NETWORK
CRYSTAL
RP
1 MΩ
RX2
C1
C2
3.072 MHz
1.5 kΩ
10 – 30 pF
40 – 60 pF
1.8432 MHz
1 MΩ
1.5 kΩ
10 – 30 pF
40 – 60 pF
Figure 21. Typical Clock Circuits
receiver buffer register (RBR)
The ACE receiver section consists of a RSR and a RBR. The RBR is actually a 64-byte FIFO. Timing is supplied
by the 16× receiver clock (RCLK). Receiver section control is a function of the ACE line control register.
The ACE RSR receives serial data from the SIN terminal. The RSR then deserializes the data and moves it into
the RBR FIFO. In the TL16C450 mode, when a character is placed in the RBR and the received data available
interrupt is enabled, an interrupt is generated. This interrupt is cleared when the data is read out of the RBR.
In the FIFO mode, the interrupts are generated based on the control setup in the FIFO control register.
scratch register
The scratch register is an 8-bit register used by the programmer as a scratchpad that temporarily holds the
programmer data without affecting any other ACE operation.
transmitter holding register (THR)
The ACE transmitter section consists of a THR and a transmitter shift register (TSR). The THR is actually a
64-byte FIFO. Timing is supplied by the baud out (BAUDOUT) clock signal. Transmitter section control is a
function of the ACE line control register.
The ACE THR receives data off the internal data bus and when the shift register is idle, moves it into the TSR.
The TSR serializes the data and outputs it at the SOUT terminal. In the TL16C450 mode, when the THR is empty
and the transmitter holding register empty (THRE) interrupt is enabled (IER1 = 1), an interrupt is generated. This
interrupt is cleared when a character is loaded into the register. In the FIFO mode, the interrupts are generated
based on the control setup in the FIFO control register.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
33
PACKAGE OPTION ADDENDUM
www.ti.com
24-Jun-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
Lead/Ball Finish
MSL Peak Temp (3)
TL16C750FN
ACTIVE
PLCC
FN
44
26
TBD
CU
Level-3-220C-168 HR
TL16C750FNR
ACTIVE
PLCC
FN
44
500
TBD
CU
Level-3-220C-168 HR
TL16C750IPM
ACTIVE
LQFP
PM
64
160
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
TL16C750PM
ACTIVE
LQFP
PM
64
160
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
TL16C750Y
OBSOLETE
XCEPT
Y
0
TBD
Call TI
Call TI
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2005, Texas Instruments Incorporated