Voltage Regulator TLE 4117 Target Data Sheet Features • Fixed output voltage regulator 1.8 V, 2.5 V, 3.3 V or 5 V • Adjustable Output down to 1.25 V • Low Drop typical 1 V • 800 mA output current • Short circuit protected • Overtemperature protected Type Ordering Code Package TLE 4117 D V Q67006-A9477 P-TO252-3-1 TLE 4117 D V18 Q67006-A9479 P-TO252-3-1 TLE 4117 D V25 Q67006-A9474 P-TO252-3-11 TLE 4117 D V33 Q67006-A9461 P-TO252-3-11 TLE 4117 D V50 Q67006-A9478 P-TO252-3-1 New device Target Data Sheet Rev. 0.1 1 P-TO252-3-1 P-TO252-3-11 2000-05-26 TLE 4117 Q I Control with Overtemperature Protection; Overcurrent Protection Adjust Internal Reference AES02839 Figure 1 Block Diagram for Adjustable Output Voltage TLE 4117 D V Target Data Sheet Rev. 0.1 2 2000-05-26 TLE 4117 I Q Control with Overtemperature Protection; Overcurrent Protection Internal Reference GND AES02840 Figure 2 Block Diagram for Fixed Output Voltage TLE 4117 D V18, 25, 33, 50 Functional Description The TLE 4117 is a 3 terminal positive adjustable or fixed voltage regulator. It is capable to supply 800 mA output current. The fixed voltage devices are available for 1.8 V, 2.5 V, 3.3 V and 5 V output voltage. The adjustable device requires 2 external resistors to define an output voltage between 1.25 V and 40 V. The TLE 4117 is packaged in surface mounted D-Pak package. The TLE 4117 voltage regulator family offers full overload protection, current limitation, thermal protection and save operation area protection (SOA). An output capacitor of 10 µF, ESR < 3 Ω is necessary for stability of the regulator loop. The input capacitor is necessary for compensating line influences e.g. to filter glitches. Using a resistor of approx. 1Ω=in series with CI , the oscillating circuit consisting of input inductance and input capacitance can be damped. De-coupling of the adjust pin at variable voltage regulator can improve the ripple rejection ratios. Target Data Sheet Rev. 0.1 3 2000-05-26 TLE 4117 Pin Configuration (top view) P-TO252-3-1 Q 1 Q Adjust I AEP02821 Figure 3 Pin Definitions and Functions TLE 4117 D V Pin No. Symbol Function 1 Adjust ADJUST 2 Q Output; the output voltage is defined by the external voltage divider between Q, Adjust and Ground. A 10 µF output capacitor with ESR < 3 Ω is required. 3 I Input Target Data Sheet Rev. 0.1 4 2000-05-26 TLE 4117 P-TO252-3-11 Q 1 Q GND I AEP02817 Figure 4 Pin Definitions and Functions TLE 4117 D Vx Fixed Voltage Devices Pin No. Symbol Function 1 GND Ground 2 Q Output; Output voltage is 1.8 V, 2.5 V, 3.3 V or 5 V. A 10 µF output capacitor with ESR < 3 Ω is required. 3 I Input Target Data Sheet Rev. 0.1 5 2000-05-26 TLE 4117 Absolute Maximum Ratings Tj = 0 to 125 °C Parameter Symbol Limit Values min. Unit Test Conditions max. Voltage Regulator Input - Output Voltage Difference (variable device only) Voltage VI 40 V – – 0.3 15 V – – 0.3 40 V – – – – Internally limited – 0.3 Input Voltage (fixed voltage version only) Voltage VI Output (fixed voltage version only) Voltage Current VQ IQ Ground (fixed voltage version only) Current IGND – 1.2 mA – Tstg – 50 150 °C – Temperature Storage temperature Note: Stresses above those listed here may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Target Data Sheet Rev. 0.1 6 2000-05-26 TLE 4117 Operating Range Parameter Symbol Limit Values min. max. Unit Remarks Input - Output voltage difference VI – VQ 1.25 40 V TLE 4117 D V Input - Voltage VI VI VI VI Tj 3.1 40 V TLE 4117 D V18 3.8 40 V TLE 4117 D V25 4.5 40 V TLE 4117 D V33 6.3 40 V TLE 4117 D V50 0 125 °C – Rthja Rthjc – 70 K/W TO-2521) – 4 K/W – Input - Voltage Input - Voltage Input - Voltage Junction temperature Thermal Resistance Junction ambient Junction case 1) Soldered in, min. footprint. Note: In the operating range, the functions given in the circuit description are fulfilled. v Target Data Sheet Rev. 0.1 7 2000-05-26 TLE 4117 Characteristics Adjustable Output Voltage Device TLE 4117 D V 0 °C < Tj < 125 °C; CQ = 10 µF, IQ = 10 mA; unless otherwise specified. Parameter Symbol Limit Values min. typ. Unit Measuring Conditions max. Reference voltage VADJ 1.2 1.25 1.3 V Adjust current IADJ ∆IADJ – 100 – µA – 1 5 µA Line regulation ∆VQ – 0.3 1.0 % Load regulation ∆VQ – 0.3 1.0 % Temperature Stability ∆VQ – 1.0 – % 1) Long Term Stability ∆VQ – 0.3 – % 1000 h; Tj = 125 °C1) Quiescent current Iq IQ max IQ min – 1 2 mA 800 – – mA VI – VQ ≤=21 V Tj = 25 °C; VI – VQ ≤=21 V – – 0 mA VDr VDr VDr – 1 1.1 V – 1.05 1.15 V – 1.1 1.2 V PSRR 60 65 – dB Adjust current change Output current Minimum Load Current Drop voltage Drop voltage Drop voltage Power Supply Ripple Rejection 1) Guaranteed by Design. 2) Measured when output voltage dropped 100 mV below nominal voltage. Target Data Sheet Rev. 0.1 8 VI – VQ = 2 V; IQ = 10 mA; Tj = 25 °C VI ≤=15 V 1 0 mA ≤ IQ ≤ 800 mA; 1.4 V ≤ VI – VQ ≤ 10 V 1.5 V ≤ VI – VQ ≤=21 V IQ = 10 mA VI – VQ ==3 V 10 mA ≤ IQ ≤ 800 mA IQ = 100 mA2) IQ = 500 mA2) IQ = 800 mA2) fr = 120 Hz; Tj = 25 °C1) Vr = 1 VPP; VI – VQ ==3 V 2000-05-26 TLE 4117 Characteristics 1.8 V Fixed Output Voltage Device TLE 4117 D V18 0 °C < Tj < 125 °C; CQ = 10 µF, IQ = 10 mA; unless otherwise specified. Parameter Symbol Limit Values min. typ. max. Unit Measuring Conditions VI = 4 V, IQ = 10 mA, Tj = 25 °C 3.2 V ≤ VI ≤=10 V 0 ≤ IQ ≤ 800 mA 3.2 V ≤ VI ≤ 15 V IQ = 0 mA VI = 3.2 V 1 mA ≤ IQ ≤ 800 mA Output voltage VQ 1.76 1.8 1.84 V Output voltage VQ 1.72 1.8 1.88 V Line regulation ∆VQ – 10 30 mV Load regulation ∆VQ – 10 30 mV Temperature Stability ∆VQ – 0.5 – % 1) Long Term Stability ∆VQ – 0.3 – % 1000 h, Tj = 125 °C1) – 1 2 mA IQ max IQ min 800 – – mA VI < 21 V Tj = 25 °C – – 0 mA VDr VDr VDr – 1 1.1 V – 1.05 1.15 V – 1.1 1.2 V PSRR 60 65 – dB Quiescent current Iq Output current Minimum Load Current Drop voltage Drop voltage Drop voltage Power Supply Ripple Rejection 1) Guaranteed by Design. 2) Measured when output voltage dropped 100 mV below nominal voltage. Target Data Sheet Rev. 0.1 9 IQ = 100 mA2) IQ = 500 mA2) IQ = 800 mA2) fr = 120 Hz, Tj = 25 °C1) Vr = 0.5 VPP, VI = 5.5 V 2000-05-26 TLE 4117 Characteristics 2.5 V Fixed Output Voltage Device TLE 4117 D V25 0 °C < Tj < 125 °C; CQ = 10 µF, IQ = 10 mA; unless otherwise specified. Parameter Symbol Limit Values min. typ. max. Unit Measuring Conditions VI = 4.5 V, IQ = 10 mA, Tj = 25 °C 3.9 V ≤ VI ≤=10 V 0 ≤ IQ ≤ 800 mA 3.9 V ≤ VI ≤ 10 V IQ = 0 mA VI = 3.9 V 1 mA ≤ IQ ≤ 800 mA Output voltage VQ 2.45 2.5 2.55 V Output voltage VQ 2.4 2.5 2.6 V Line regulation ∆VQ – 10 30 mV Load regulation ∆VQ – 10 30 mV Temperature Stability ∆VQ – 1.0 – % 1) Long Term Stability ∆VQ – 0.3 – % 1000 h, Tj = 125 °C1) – 1 2 mA IQ max IQ min 800 – – mA VI < 10 V Tj = 25 °C, VI < 23 V – – 0 mA VDr VDr VDr – 1 1.1 V – 1.05 1.15 V – 1.1 1.2 V PSRR 60 65 – dB Quiescent current Iq Output current Minimum Load Current Drop voltage Drop voltage Drop voltage Power Supply Ripple Rejection 1) Guaranteed by Design. 2) Measured when output voltage dropped 100 mV below nominal voltage. Target Data Sheet Rev. 0.1 10 IQ = 100 mA2) IQ = 500 mA2) IQ = 800 mA2) fr = 120 Hz, Tj = 25 °C1) Vr = 1 VPP, VI = 5.5 V 2000-05-26 TLE 4117 Characteristics 3.3 V Fixed Output Voltage Device TLE 4117 D V33 0 °C < Tj < 125 °C; CQ = 10 µF, IQ = 10 mA; unless otherwise specified. Parameter Symbol Limit Values min. typ. max. Unit Measuring Conditions VI = 5.3 V, IQ = 10 mA, Tj = 25 °C 4.75 V ≤ VI ≤=10 V 0 ≤ IQ ≤ 800 mA 4.75 V ≤ VI ≤ 15 V IQ = 0 mA VI = 4.75 V 1 mA ≤ IQ ≤ 800 mA Output voltage VQ 3.24 3.3 3.36 V Output voltage VQ 3.16 3.3 3.44 V Line regulation ∆VQ – 10 30 mV Load regulation ∆VQ – 10 30 mV Temperature Stability ∆VQ – 1.0 – % 1) Long Term Stability ∆VQ – 0.3 – % 1000 h, Tj = 125 °C1) – 1 2 mA IQ max IQ min 800 – – mA VI < 15 V Tj = 25 °C; VI < 24 V – – 0 mA VDr VDr VDr – 1 1.1 V – 1.05 1.15 V – 1.1 1.2 V PSRR 60 65 – dB Quiescent current Iq Output current Minimum Load Current Drop voltage Drop voltage Drop voltage Power Supply Ripple Rejection 1) Guaranteed by Design. 2) Measured when output voltage dropped 100 mV below nominal voltage. Target Data Sheet Rev. 0.1 11 IQ = 100 mA2) IQ = 500 mA2) IQ = 800 mA2) fr = 120 Hz, Tj = 25 °C1) Vr = 0.5 VPP, VI = 5 V 2000-05-26 TLE 4117 Characteristics 5 V Fixed Output Voltage Device TLE 4117 D V50 0 °C < Tj < 125 °C; CQ = 10 µF, IQ = 10 mA; unless otherwise specified. Parameter Symbol Limit Values min. typ. max. Unit Measuring Conditions VI = 7 V, IQ = 10 mA, Tj = 25 °C 6.5 V ≤ VI ≤=10 V 0 ≤ IQ ≤ 800 mA 6.5 V ≤ VI ≤ 15 V IQ = 0 mA VI = 6.5 V 1 mA ≤ IQ ≤ 800 mA Output voltage VQ 4.9 5.0 5.1 V Output voltage VQ 4.8 5.0 5.2 V Line regulation ∆VQ – 10 50 mV Load regulation ∆VQ – 10 50 mV Temperature Stability ∆VQ – 1.0 – % 1) Long Term Stability ∆VQ – 0.3 – % 1000 h, Tj = 125 °C1) – 1 2 mA IQ max IQ min 800 – – mA VI < 15 V Tj = 25 °C; VI < 26 V – – 0 mA VDr VDr VDr – 1 1.1 V – 1.05 1.15 V – 1.1 1.2 V PSRR 60 65 – dB Quiescent current Iq Output current Minimum Load Current Drop voltage Drop voltage Drop voltage Power Supply Ripple Rejection 1) Guaranteed by Design. 2) Measured when output voltage dropped 100 mV below nominal voltage. IQ = 100 mA2) IQ = 500 mA2) IQ = 800 mA2) fr = 120 Hz, Tj = 25 °C Vr = 0.5 VPP, VI = 5 V Note: The listed characteristics are ensured over the operating range of the integrated circuit. Typical characteristics specify mean values expected over the production spread. If not otherwise specified, typical characteristics apply at TA = 25 °C and the given supply voltage. Target Data Sheet Rev. 0.1 12 2000-05-26 TLE 4117 TLE 4117 IQ II VI Q I CI CQ 100 nF 10 µF R1 Adjust VQ IAdjust R2 AES02836 Figure 5 Measuring Circuit Variable Output Voltage TLE 4117 V TLE 4117DV18, 25, 33, 50 II VI CI I Q IQ CQ 10 µF 100 nF VQ GND IGND AES02812 Figure 6 Measuring Circuit Fixed Output Voltage TLE 4117 D V18, 25, 33, 50 Target Data Sheet Rev. 0.1 13 2000-05-26 TLE 4117 TLE 4117 VI I CI1 VQ Q CQ1 CI2 10 µF CQ2 R1 Adjust R2 VREF = VQ - VADJ CADJ AES02837 R R1 V Q = V REF × 1 + -----2- + I ADJ × R 2 Figure 7 Appliation Circuit Variable Output Voltage TLE 4117 V Output Voltage 1.8 V, 2.5 V, 3.3 V or 5 V TLE 4117 VI I C I1 VQ Q CQ1 C I2 10 µF CQ2 GND AES02838 Figure 8 Application Circuit Fixed Output Voltage TLE 4117 D V18, 25, 33, 50 Target Data Sheet Rev. 0.1 14 2000-05-26 TLE 4117 Package Outlines P-TO252-3-1 (Plastic Transistor Single Outline) 6.5 +0.15 -0.10 2.3 +0.05 -0.10 4.57 0.51 min 0.15 max per side 0.9 +0.08 -0.04 B 0.8 ±0.15 9.9 ±0.5 6.22 -0.2 1 ±0.1 A 5.4 ±0.1 3x 0.75 ±0.1 0...0.15 0.5 +0.08 -0.04 2.28 1 ±0.1 0.25 M A B 0.1 GPT09051 All metal surfaces tin plated, except area of cut. Sorts of Packing Package outlines for tubes, trays etc. are contained in our Data Book “Package Information”. SMD = Surface Mounted Device Target Data Sheet Rev. 0.1 15 Dimensions in mm 2000-05-26 TLE 4117 P-TO252-3-11 (Plastic Transistor Single Outline) 6.5 +0.15 -0.05 A B (5) 0.9 +0.20 -0.01 0...0.15 3x 0.75 ±0.1 0.5 +0.08 -0.04 2.28 0.1 B 0.25 M A B All metal surfaces tin plated, except area of cut. Sorts of Packing Package outlines for tubes, trays etc. are contained in our Data Book “Package Information”. SMD = Surface Mounted Device Target Data Sheet Rev. 0.1 16 GPT09277 4.57 0.5 +0.08 -0.04 0.51 min. 0.15 max. per side 2.3 +0.05 -0.10 0.8 ±0.15 (4.24) 1 ±0.1 9.98 ±0.5 6.22 -0.2 5.4 ±0.1 Dimensions in mm 2000-05-26 TLE 4117 Edition 2000-05-26 Published by Infineon Technologies AG, St.-Martin-Strasse 53, D-81541 München, Germany © Infineon Technologies AG 2000. All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be considered as warranted characteristics. Terms of delivery and rights to technical change reserved. We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated herein. Infineon Technologies is an approved CECC manufacturer. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office in Germany or our Infineon Technologies Representatives worldwide (see address list). Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. Target Data Sheet Rev. 0.1 17 2000-05-26