! " # $% # 1.1 Display type: TN 1.2 Display color*: Display color: Blue-Black Background: White 1.3 Polarizer mode: Reflective/Positive 1.4 Viewing Angle: 6:00 1.5 Driving Method: 1/16 Duty 1/5 Bias 1.6 Backlight: None 1.7 Display Fonts: 5 x 7 dots + Cursor (1 Character) 1.8 Controller: HCD66701A00 1.9 Data Transfer: 8 Bit Parallel 1.10 Operating Temperature: 0----+50 Storage Temperature: -20----+60 1.11 Outline Dimensions: Refer to outline drawing on next page 1.12 Dot Matrix: 16 Characters X 2 Lines 1.13 Dot Size: 0.55X0.50(mm) 1.14 Dot Pitch: 0.60X0.55 (mm) 1.15 Weight: 20g 1.16 PCB edtion: TM162AD P1-2 * Color tone is slightly changed by temperature and driving voltage. 2. Outline Drawing http://66.70.139.101/assetts/drawings/162ag.dwf 4/6/01 )*+'#'! ! NONE6 ! ,'-#! .#'+/!'! Item Symbol Min. Max. Power Supply Voltage V V -0.3 7.0 Unit Remark V LCD Driving Voltage V -0.3 13.0 Operating Temperature Range T 0 +50 Storage Temperature Range T -20 +60 No Condensation 0## ' 6.1 Electrical characteristics Item Symbol Min. Typ. Max. Unit Supply Voltage (Logic) V V 4.5 5.0 5.5 V Supply Voltage (LCD Drive) V - 4.7 - V 0.7V - V+0.3 V -0.3 - 0.2 V V I V =5.0 - 1.5 2.0 mA I - 0.40 0.6 mA Input Signal Voltage V High V=5.0 Low Supply current (Logic) Supply current (LCD Drive) V V=5.0 V 6.2 Interface Signals Pin No. Symbol Level Description 1 Vss 0V 2 Vcc 5.0V Power supply voltage for logic and LCD(+) 3 Vee 0.3V Power supply voltage for LCD(-) 4 RS H/L Selects registers 5 R/W H/L Selects read or write 6 E H/L Starts data read/write 7 DB0 H/L Data bit0 8 DB1 H/L Data bit1 9 DB2 H/L Data bit2 10 DB3 H/L Data bit3 11 DB4 H/L Data bit4 12 DB5 H/L Data bit5 13 DB6 H/L Data bit6 14 DB7 H/L Data bit7 " NC - No signal NC - No signal Ground 6.3 Interface Timing Chart 3 AC Characteristics (VCC = 2.7 to 5.5V, Ta = –30 to +75°C* ) Write Operation Symbol Min Typ Max Item 1000 — — t cycE Enable cycle time PWEH 450 — — Enable pulse width (high level) t Er, t Ef — — 25 Enable rise/fall time 40 — — Address set-up time (RS, R/W to E) t AS t AH 20 — — Address hold time t DSW 195 — — Data set-up time tH 10 — — Data hold time Read Operation Item Symbol Min Typ Max Enable cycle time 1000 — — t cycE Enable pulse width (high level) PWEH 450 — — Enable rise/fall time t Er, t Ef — — 25 Address set-up time (RS, R/W to E) t AS 40 — — Address hold time t AH 20 — — Data delay time t DDR — — 350 Data hold time t DHR 10 — — Unit Test Condition ns Unit ns Test Condition Timing Characteristics VIH1 RS VIL1 t AS R/W VIL1 E DB0 to DB7 VIH1 RS VIL1 t AS VIH1 R/W E DB0 to DB7 VIH1 VIL1 t AH VIL1 PWEH t AH t Ef VIH1 VIL1 VIH1 VIL1 t Er tH t DSW VIH1 VIL1 VIL1 VIH1 VIL1 Valid data t cycE Write Operation VIH1 VIL1 t AH VIH1 PWEH t AH t Ef VIH1 VIL1 VIH1 VIL1 VIL1 t Er t DHR t DDR VOH1 VOL1 Valid data t cycE Read Operation VOH1 VOL1 6.4 Instruction Code Instruction RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Description Execution Time (max) (when f cp or f OSC is 320 kHz) Clear display 0 0 0 0 0 0 0 0 0 1 Clears entire display and sets DDRAM address 0 in address counter. 1.28 ms Return home 0 0 0 0 0 0 0 0 1 — Sets DDRAM address 0 in address counter. Also returns display from being shifted to original position. DDRAM contents remain unchanged. 1.28 ms Entry mode 0 set 0 0 0 0 0 0 1 I/D S Sets cursor move direction 31 µs and specifies display shift. These operations are performed during data write and read. Display on/off control 0 0 0 0 0 0 1 D C B Sets entire display (D) 31 µs on/off, cursor on/off (C), and blinking of cursor position character (B). Cursor or 0 display shift 0 0 0 0 1 S/C R/L — — Moves cursor and shifts display without changing DDRAM contents. Function set 0 0 0 0 1 DL N — — Sets interface data length 31 µs (DL), number of display lines (L), and character font (F). Set CGRAM address 0 0 0 1 ACG ACG ACG ACG ACG ACG Sets CGRAM address. CGRAM data is sent and received after this setting. 31 µs Set DDRAM address 0 0 1 ADD ADD ADD ADD ADD ADD ADD Sets DDRAM address. DDRAM data is sent and received after this setting. 31 µs Read busy 0 flag & address 1 BF AC Code AC AC AC F AC AC AC 31 µs Reads busy flag (BF) 0 µs indicating internal operation is being performed and reads address counter contents. Execution Time (max) (when f cp or f OSC is 320 kHz) Code Instruction RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Description Write data to CG or DDRAM 1 0 Write data Writes data into DDRAM or CGRAM. 31 µs tADD = 4.7 µs* Read data 1 from CG or DDRAM 1 Read data Reads data from DDRAM or CGRAM. 31 µs tADD = 4.7 µs* DDRAM: Display data RAM CGRAM: Character generator RAM ACG: CGRAM address ADD: DDRAM address (corresponds to cursor address) AC: Address counter used for both DD and CGRAM addresses Execution time changes when frequency changes Example: When fcp or fOSC is 270 kHz, 320 31 µs × = 37 µs 270 I/D I/D S S/C S/C R/L R/L DL N F BF BF Note: = 1: = 0: = 1: = 1: = 0: = 1: = 0: = 1: = 1: = 1: = 1: = 0: Increment Decrement Accompanies display shift Display shift Cursor move Shift to the right Shift to the left 8 bits, DL = 0: 4 bits 2 lines, N = 0: 1 line 5 × 10 dots, F = 0: 5 × 7 dots Internally operating Instructions acceptable — indicates no effect. * After execution of the CGRAM/DDRAM data write or read instruction, the RAM address counter is incremented or decremented by 1. The RAM address counter is updated after the busy flag turns off. In Figure 10, tADD is the time elapsed after the busy flag turns off until the address counter is updated. Busy signal (DB7 pin) Address counter (DB0 to DB6 pins) Busy state A A+1 t ADD Note: t ADD depends on the operation frequency t ADD = 1.5/(f cp or f OSC ) seconds Figure 10 Address Counter Update 6.5 Character generator ROM(HCD66701A00) Lower 4 Bits Upper 4 Bits 0000 0010 0011 0100 0101 0110 0111 1010 1011 1100 1101 1110 1111 xxxx0000 CG RAM (1) xxxx0001 (2) xxxx0010 (3) xxxx0011 (4) xxxx0100 (5) xxxx0101 (6) xxxx0110 (7) xxxx0111 (8) xxxx1000 (1) xxxx1001 (2) xxxx1010 (3) xxxx1011 (4) xxxx1100 (5) xxxx1101 (6) xxxx1110 (7) xxxx1111 (8) Note: The user can specify any pattern for character-generator RAM. 1# 7.1 Optical Characteristics Item Symbol Ta=25 Condition =0 Response Time Turn off -- Max. C Unit 10 Deg Turn on 35 Typ. C Viewing Angle Contrast Ratio Min. =0 =20 =0 T -30 -- 30 3.0 - - - - 150 =20 =0 T ms - - 150 7.2 Definition of Optical Characteristics 7.2.1 Definition of Viewing Angle Top Top Bottom 7.2.2 Definition of Contrast Ratio Bottom Measuring Conditions: 1) Ambient Temperature: 25 ; 2) Frame frequency: 64Hz 7.2.3 Definition of Response time Turn on time: = + Measuring Condition: 1) Operating Voltage: 4.7V Turn off time: = + 2) Frame frequency: 64Hz 2## 8.1 Content of Reliability Test No. Test Item 1 High Temperature Storage Low Temperature 2 Storage 3 4 5 6 Content of Test Endurance test applying the high storage temperature for a long time Endurance test applying the low storage temperature for a long time Endurance test applying the High Temperature electric stress (voltage current) Operation and the thermal stress to the element for a long time Endurance test applying the Low Temperature electric stress under low Operation temperature for a long time Endurance test applying the high High Temperature temperature and high humidity /Humidity Storage storage for a long time Endurance test applying the low and high temperature cycle Temperature -20 25 60 25 Cycle 30min 5min 30min 5min 1 cycle 7 Vibration Test (package state) Endurance test applying the vibration during transportation 8 Shock Test (package state) Endurance test applying the shock during transportation 9 Atmospheric Pressure Test Endurance test applying the atmospheric pressure during transportation by air Ta=25 Test condition 60 96H -20 96H 50 96H 0 96H 40 90%RH 96H -20 /60 10 cycles 10Hz~150Hz, 50m/s, 40min Half- sine wave, 100m/s, 11ms 40kPa 16H 8.2 Failure Judgment Criterion Criterion Item Test Item No. Failure Judgement Criterion 1 2 3 4 5 6 7 8 9 Basic Specification Out of the basic Specification Electrical specification Mechanical Specification Optical Characteristic Note Remark Out of the electrical specification Out of the mechanical specification Out of the optical specification For test item refer to 8.1 Basic specification = Optical specification + Mechanical specification 345*67** Examination At Ta=25 or Test (unless otherwise stated) Inspection Min. Max. Unit IL AQL Major 1.0 II Minor 2.5 Major 1.0 Display II Minor Defects 2.5 Note: Major defects: Open segment or common, Short, Serious damages, Leakage Miner defects: Others Sampling standard conforms to GB2828 External Visual Inspection Under normal illumination and eyesight condition, the See Appendix A distance between eyes and LCD is 25cm. Under normal illumination and eyesight condition, See Appendix B display on inspection. $8' 5*+'# 10.1 Handling Precautions 10.1.1 The display panel is made of glass. Do not subject it to a mechanical shock by dropping it from a high place, etc. 10.1.2 If the display panel is damaged and the liquid crystal substance inside it leaks out, be sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water. 10.1.3 Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. 10.1.4 The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle this polarizer carefully. 10.1.5 If the display surface is contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If still not completely clear, moisten cloth with one of the following solvents: Isopropyl alcohol Ethyl alcohol Solvents other than those mentioned above may damage the polarizer. Especially, do not use the following: Water Ketone Aromatic solvents 10.1.6 Do not attempt to disassemble the LCD Module. 10.1.7 If the logic circuit power is off, do not apply the input signals. 10.1.8 To prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment. a. Be sure to ground the body when handling the LCD Modules. b. Tools required for assembly, such as soldering irons, must be properly ground. c. To reduce the amount of static electricity generated, do not conduct assembly and other work under dry conditions. d. The LCD Module is coated with a film to protect the display surface. Be care when peeling off this protective film since static electricity may be generated. 10.2 Storage precautions 10.2.1 When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps. 10.2.2 The LCD modules should be stored under the storage temperature range. If the LCD modules will be stored for a long time, the recommend condition is: 40 Temperature : 0 80% Relatively humidity: 10.2.3 The LCD modules should be stored in the room without acid, alkali and harmful gas. 10.3 The LCD modules should be no falling and violent shocking during transportation, and also should avoid excessive press, water, damp and sunshine. / Inspection items and criteria for appearance defects Items Contents Criteria Leakage Not permitted Rainbow According to the limit specimen Polarizer Black spot (in viewing area) Wrong polarizer attachment Not permitted Bubble between polarizer and glass Not counted Scratches of polarizer According to the limit specimen φ<0.3mm Max. 3 defects allowed 0.3mm φ 0.5mm Not counted Max. 3 spots allowed X<0.2mm 0.2mm X 0.5mm X=(a+b)/2 Black line (in viewing area) Not counted Max. 3 lines allowed a<0.02mm 0.02mm a 0.05mm b 2.0mm Progressive cracks Not permitted Max. 3 spots (lines) allowed /- Inspection items and criteria for display defects Items Contents Criteria Open segment or open common Not permitted Short Not permitted Wrong viewing angle Not permitted Contrast radio uneven According to the limit specimen Crosstalk According to the limit specimen Not counted Max.3 dots allowed X<0.1mm 0.1mm X 0.2mm X=(a+b)/2 Pin holes and cracks in segment (DOT) Black spot (in viewing area) Not counted Max.2 dots allowed A<0.1mm 0.1mm A 0.2mm D<0.25mm Not counted Max.3 spots allowed X<0.1mm 0.1mm X 0.2mm X=(a+b)/2 Black line (in viewing area) Not counted Max.3 lines allowed a<0.02mm 0.02mm a 0.05mm b 0.5mm Max.3 dots allowed Max.3 spots (lines) allowed WWW.ALLDATASHEET.COM Copyright © Each Manufacturing Company. All Datasheets cannot be modified without permission. This datasheet has been download from : www.AllDataSheet.com 100% Free DataSheet Search Site. Free Download. No Register. Fast Search System. www.AllDataSheet.com