TS5N214 2-BIT 1-OF-4 FET MULTIPLEXER/DEMULTIPLEXER HIGH-BANDWIDTH BUS SWITCH www.ti.com SCDS206 – AUGUST 2005 FEATURES • • • • • • • • DBQ OR PW PACKAGE (TOP VIEW) Low and Flat ON-State Resistance (ron) Characteristics Over Operating Range (ron = 3 Ω Typ) 0- to 10-V Switching on Data I/O Ports Bidirectional Data Flow With Near-Zero Propagation Delay Low Input/Output Capacitance Minimizes Loading and Signal Distortion (Cio(OFF) = 20 pF Max, B Port) VCC Operating Range From 4.75 V to 5.25 V Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II ESD Performance Tested Per JESD 22 – 2000-V Human-Body Model (A114-B, Class II) – 1000-V Charged-Device Model (C101) Supports Both Digital and Analog Applications: PCI Interface, Differential Signal Interface, Memory Interleaving, Bus Isolation, Low-Distortion Signal Gating 1OE S1 1B4 1B3 1B2 1B1 1A GND 1 16 2 15 3 14 4 13 5 12 6 7 11 10 8 9 VCC 2OE S0 2B4 2B3 2B2 2B1 2A XXXXXX DESCRIPTION/ORDERING INFORMATION The TS5N214 is a high-bandwidth FET bus switch utilizing a charge pump to elevate the gate voltage of the pass transistor, providing a low and flat ON-state resistance (ron). The low and flat ON-state resistance allows for minimal propagation delay and supports rail-to-rail switching on the data input/output (I/O) ports. The device also features low data I/O capacitance to minimize capacitive loading and signal distorion on the data bus. Specifically designed to support high-bandwidth applications, the TS5N214 provides an optimized interface solution ideally suited for broadband communications, networking, and data-intensive computing systems. The TS5N214 is a 2-bit 1-of-4 multiplexer/demultiplexer with separate output-enable (1OE, 2OE) inputs. The select (S0, S1) inputs control the data path of the multiplexer/demultiplexer. When OE is low, the multiplexer/demultiplexer is enabled and the A port is connected to the B port, allowing bidirectional data flow between ports. When OE is high, the multiplexer/demultiplexer is disabled and a high-impedance state exists between the A and B ports. This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry prevents damaging current backflow through the device when it is powered down. The device has isolation during power off. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. ORDERING INFORMATION PACKAGE (1) TA –40°C to 85°C (1) ORDERABLE PART NUMBER TOP-SIDE MARKING SSOP (QSOP) – DBQ Tape and reel TS5N214DBQR YB214 TSSOP – PW Tape and reel TS5N214PWR YB214 Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2005, Texas Instruments Incorporated TS5N214 2-BIT 1-OF-4 FET MULTIPLEXER/DEMULTIPLEXER HIGH-BANDWIDTH BUS SWITCH www.ti.com SCDS206 – AUGUST 2005 FUNCTION TABLE (EACH MULTIPLEXER/DEMULTIPLEXER) INPUTS OE S1 S0 INPUT/OUTPUT A FUNCTION L L L B1 A port = B1 port L L H B2 A port = B2 port L H L B3 A port = B3 port L H H B4 A port = B4 port H X X Z Disconnect LOGIC DIAGRAM (POSITIVE LOGIC) 7 1A 6 SW 5 SW 1B1 1B2 4 SW 1B3 3 1B4 SW 9 2A 10 2B1 SW 11 SW 2B2 12 2B3 SW 13 SW 14 S0 2 S1 1 1OE 2OE 2 15 2B4 TS5N214 2-BIT 1-OF-4 FET MULTIPLEXER/DEMULTIPLEXER HIGH-BANDWIDTH BUS SWITCH www.ti.com SCDS206 – AUGUST 2005 SIMPLIFIED SCHEMATIC, EACH FET SWITCH (SW) A B VCC Charge Pump EN(1) (1) EN is the internal enable signal applied to the switch. Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT VCC Supply voltage range –0.5 7 V VIN Control input voltage range (2) (3) –0.5 7 V VI/O Switch I/O voltage range (2) (3) (4) –0.5 11 V II/O ON-state switch current (5) Continuous current through VCC or GND θJA Package thermal impedance (6) Tstg Storage temperature range (1) (2) (3) (4) (5) (6) ±100 mA ±100 mA DBQ package 90 PW package 108 –65 150 °C/W °C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltages are with respect to ground, unless otherwise specified. The input and output voltage ratings may be exceeded if the input and output clamp-current ratings are observed. VI and VO are used to denote specific conditions for VI/O. II and IO are used to denote specific conditions for II/O. The package thermal impedance is calculated in accordance with JESD 51-7. Recommended Operating Conditions (1) MIN MAX UNIT VCC Supply voltage 4.75 5.25 V VIH High-level control input voltage 2 5.25 V VIL Low-level control input voltage 0 0.8 V VI/O Data input/output voltage 0 10 V TA Operating free-air temperature –40 85 °C (1) All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. 3 TS5N214 2-BIT 1-OF-4 FET MULTIPLEXER/DEMULTIPLEXER HIGH-BANDWIDTH BUS SWITCH www.ti.com SCDS206 – AUGUST 2005 Electrical Characteristics over recommended operating free-air temperature range (unless otherwise noted) TEST CONDITIONS (1) PARAMETER IIN Control inputs MIN TYP (2) MAX µA VIN = 0 to VCC VCC = 5.25 V, VO = 0 to 10 V, VI = 0, Switch OFF, VIN = VCC or GND 10 VCC = 0 V, VO = Open, VI = 0 to 10 V 10 VCC = 5.25 V, II/O = 0, Switch ON or OFF, VIN = VCC or GND 10 mA VCC = 5 V, VIN = 10 V or 0 10 pF A port VCC = 5 V, Switch OFF, VIN = VCC or GND, VI/O = 10 V or 0 60 B port VCC = 5 V, Switch OFF, VIN = VCC or GND, VI/O = 10 V or 0 20 Cio(ON) VCC = 5 V, Switch ON, VIN = VCC or GND, VI/O = 10 V or 0 100 VCC = 4.75 V, TYP at VCC = 5 V VI = 0 V, IO = 50 mA ron (4) VI = 8 V, IO = –50 mA 7.5 VI = 10 V, IO = –50 mA 12.5 IOZ (3) ICC Cin Control inputs Cio(OFF) (1) (2) (3) (4) 10 UNIT VCC = 5.25 V, µA pF 3 pF 7.5 Ω VIN and IIN refer to control inputs. VI, VO, II, and IO refer to data pins. All typical values are at VCC = 5 V (unless otherwise noted), TA = 25°C. For I/O ports, the parameter IOZ includes the I/O leakage current. Measured by the voltage drop between the A and B terminals at the indicated current through the switch. ON-state resistance is determined by the lower of the voltages of the two (A or B) terminals. Switching Characteristics over recommended operating free-air temperature range (unless otherwise noted) (see Figure 3) FROM (INPUT) TO (OUTPUT) tpd (1) A or B B or A tpd(s) S S OE PARAMETER ten tdis (1) VCC = 5 V ± 0.25 V MIN UNIT MAX 3 ns A 200 ns B 200 A or B 200 S B 200 OE A or B 200 ns ns The propagation delay is the calculated RC time constant of the typical ON-state resistance of the switch and the specified load capacitance, when driven by an ideal voltage source (zero output impedance). Dynamic Characteristics over recommended operating free-air temperature range, VCC = 5 V ± 5% (unless otherwise noted) PARAMETER MIN TYP (1) MAX TEST CONDITIONS UNIT RL = 50 Ω, VI = 0.632 V (P-P), See Figure 4 OFF isolation (OISO) RL = 50 Ω, VI = 0.632 V (P-P), f = 25 MHz, See Figure 5 –50 dB RL = 50 Ω, VI = 0.632 V (P-P), f = 25 MHz, See Figure 6 and Figure 7 –50 dB Bandwidth (BW) (2) Crosstalk (XTALK) (1) (2) 4 All typical values are at VCC = 5 V (unless otherwise noted), TA = 25°C Bandwidth is the frequency where the gain is –3 dB below the DC gain. 25 MHz TS5N214 2-BIT 1-OF-4 FET MULTIPLEXER/DEMULTIPLEXER HIGH-BANDWIDTH BUS SWITCH www.ti.com SCDS206 – AUGUST 2005 TYPICAL PERFORMANCE ron − ON-State Resistance − Ω 6 5 TA = 25°C 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 10 VI − V Figure 1. Typical ron vs VI, VCC - 5 V, and IO = –50 mA 0 0 −1 Phase −20 Gain − dB −3 −4 −30 −5 −40 −6 −50 Phase Margin − Deg −10 Gain −2 −7 −60 −8 −9 0.1 −70 1 10 100 500 f − Frequency − MHz Figure 2. Frequency Response vs Bandwidth 5 TS5N214 2-BIT 1-OF-4 FET MULTIPLEXER/DEMULTIPLEXER HIGH-BANDWIDTH BUS SWITCH www.ti.com SCDS206 – AUGUST 2005 180 160 140 120 100 80 60 40 20 0 −20 −40 −60 −80 −100 −120 −140 −160 −180 0 −20 Phase Gain − dB −40 −60 Gain −80 −100 −120 0.1 1 10 100 Phase Margin − Deg TYPICAL PERFORMANCE (continued) 500 f − Frequency − MHz 0 −20 Phase Gain − dB −40 −60 Gain −80 −100 −120 0.1 1 10 100 f − Frequency − MHz Figure 4. Frequency Response vs Crosstalk 6 180 160 140 120 100 80 60 40 20 0 −20 −40 −60 −80 −100 −120 −140 −160 −180 500 Phase Margin − Deg Figure 3. Frequency Response vs OFF Isolation TS5N214 2-BIT 1-OF-4 FET MULTIPLEXER/DEMULTIPLEXER HIGH-BANDWIDTH BUS SWITCH www.ti.com SCDS206 – AUGUST 2005 PARAMETER MEASUREMENT INFORMATION VCC Input Generator VIN 50 Ω 50 Ω VG1 TEST CIRCUIT DUT 2 VCC Input Generator VI 50 Ω 50 Ω CL (see Note A) RL TEST VCC S1 RL VI CL tpd(s)† 5 V ± 0.25 V Open 100 Ω VCC 35 pF tPLZ/tPZL 5 V ± 0.25 V 2 VCC 100 Ω GND 35 pF 0.3 V tPHZ/tPZH 5 V ± 0.25 V GND 100 Ω VCC 35 pF 0.3 V V∆ tpds is measured with Demux inputs at opposite voltage levels, i.e. VB1 = 5 V, VB2 = GND. VCC Output Control (VIN) VCC/2 VCC VCC/2 VCC/2 0V tPLH VOH Output VCC/2 VCC/2 VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES (tpd(s)) Output Waveform 1 S1 at 2 × VCC (see Note B) tPLZ VOH VCC/2 VOL + V∆ VOL tPZH tPHL VCC/2 0V tPZL Output Control (VIN) Open GND VG2 † S1 RL VO Output Waveform 2 S1 at GND (see Note B) tPHZ VOH VCC/2 VOH − V∆ 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr < 25 ns, tf < 25 ns. D. The outputs are measured one at a time, with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd(s). The tpd propagation delay is the calculated RC time constant of the typical ON-state resistance of the switch and the specified load capacitance, when driven by an ideal voltage source (zero output impedance). H. All parameters and waveforms are not applicable to all devices. Figure 5. Test Circuit and Voltage Waveforms 7 TS5N214 2-BIT 1-OF-4 FET MULTIPLEXER/DEMULTIPLEXER HIGH-BANDWIDTH BUS SWITCH www.ti.com SCDS206 – AUGUST 2005 PARAMETER MEASUREMENT INFORMATION (continued) VCC Network Analyzer 50 B1 Channel ON: B1 to A A Source Signal Network Analyzer Setup B2−B4 Source Power = 0 dBM (632-mV P-P at 50- load) GND DC Bias = 350 mV 50 Figure 6. Bandwidth (BW) VCC Network Analyzer 50 B1 Channel OFF: B2−B4 to A A Source Signal 50 Network Analyzer Setup B2−B4 Source Power = 0 dBM (632-mV P-P at 50- load) GND 50 DC Bias = 350 mV Figure 7. OFF Isolation (OISO) VCC Network Analyzer 50 B1 Channel ON: B1 to A A Source Signal Channel OFF: B2−B4 to A B2−B4 Network Analyzer Setup 50 50 GND Source Power = 0 dBM (632-mV P-P at 50- load) DC Bias = 350 mV Figure 8. Crosstalk (XTALK) 8 TS5N214 2-BIT 1-OF-4 FET MULTIPLEXER/DEMULTIPLEXER HIGH-BANDWIDTH BUS SWITCH www.ti.com SCDS206 – AUGUST 2005 PARAMETER MEASUREMENT INFORMATION (continued) V+ Network Analyzer 50 Channel ON: 1B1 to 1A, 2B1 to 2A 1B1 1A Source Signal Network Analyzer Setup 2B1 50 2A 50 Source Power = 0 dBM (632 mV P-P at 50 load) DC Bias = 350 mV GND Figure 9. Adjacent Channel Crosstalk (XTALK) 9 TS5N214 2-BIT 1-OF-4 FET MULTIPLEXER/DEMULTIPLEXER HIGH-BANDWIDTH BUS SWITCH www.ti.com SCDS206 – AUGUST 2005 MECHANICAL DATA DBQ (R–PDSO–G**) PLASTIC SMALL-OUTLINE PACKAGE 0.012 (0,30) 0.008 (0,20) 0.025 (0,64) 24 0.005 (0,13) 13 0.157 (3,99) 0.150 (3,81) 0.244 (6,20) 0.228 (5,80) 0.008 (0,20) NOM Gauge Plane 1 12 A 0.010 (0,25) 0°−8° 0.035 (0,89) 0.016 (0,40) 0.069 (1,75) MAX Seating Plane 0.010 (0,25) 0.004 (0,10) 0.004 (0,10) PINS ** 16 20 24 28 A MAX 0.197 (5,00) 0.344 (8,74) 0.344 (8,74) 0.394 (10,01) A MIN 0.189 (4,80) 0.337 (8,56) 0.337 (8,56) 0.386 (9,80) M0−137 VARIATION AB AD AE AF DIM D 4073301/F 02/2002 10 A. All linear dimensions are in inches (millimeters). B. This drawing is subject ot change without notice. C. Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15). D. Falls within JEDEC MO-137. TS5N214 2-BIT 1-OF-4 FET MULTIPLEXER/DEMULTIPLEXER HIGH-BANDWIDTH BUS SWITCH www.ti.com SCDS206 – AUGUST 2005 MECHANICAL DATA (continued) PW (R–PDSO–G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0°− 8° A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX 0,10 PINS ** 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. C. Body dimensions do not include mold flash or protrusion not to exceed 0, 15. D. Falls within JEDEC MO-153 11 PACKAGE OPTION ADDENDUM www.ti.com 24-May-2007 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TS5N214DBQR ACTIVE SSOP/ QSOP DBQ 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TS5N214DBQRE4 ACTIVE SSOP/ QSOP DBQ 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TS5N214DBQRG4 ACTIVE SSOP/ QSOP DBQ 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TS5N214PW ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TS5N214PWE4 ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TS5N214PWG4 ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TS5N214PWR ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TS5N214PWRE4 ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TS5N214PWRG4 ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 30-Jul-2010 TAPE AND REEL INFORMATION *All dimensions are nominal Device TS5N214PWR Package Package Pins Type Drawing TSSOP PW 16 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2000 330.0 12.4 Pack Materials-Page 1 6.9 B0 (mm) K0 (mm) P1 (mm) 5.6 1.6 8.0 W Pin1 (mm) Quadrant 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 30-Jul-2010 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TS5N214PWR TSSOP PW 16 2000 346.0 346.0 29.0 Pack Materials-Page 2 MECHANICAL DATA MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0°– 8° A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DLP® Products www.dlp.com Communications and Telecom www.ti.com/communications DSP dsp.ti.com Computers and Peripherals www.ti.com/computers Clocks and Timers www.ti.com/clocks Consumer Electronics www.ti.com/consumer-apps Interface interface.ti.com Energy www.ti.com/energy Logic logic.ti.com Industrial www.ti.com/industrial Power Mgmt power.ti.com Medical www.ti.com/medical Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Space, Avionics & Defense www.ti.com/space-avionics-defense RF/IF and ZigBee® Solutions www.ti.com/lprf Video and Imaging www.ti.com/video Wireless www.ti.com/wireless-apps Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2010, Texas Instruments Incorporated