UBA2016A/15/15A 600 V fluorescent lamp driver with PFC, linear dimming and boost function Rev. 1 — 20 May 2011 Objective data sheet 1. General description The UBA2016A/15/15A are high voltage Integrated Circuits (IC) intended to drive fluorescent lamps with filaments such as Tube Lamps (TL) and Compact Fluorescent Lamps (CFL) in general lighting applications. The IC comprises a fluorescent lamp control module, half-bridge driver, built-in critical conduction mode Power Factor Correction (PFC) controller/driver and several protection mechanisms. The IC drives fluorescent lamp(s) using a half-bridge circuit made of two MOSFETs with a supply voltage of up to 600 V. The UBA2016A/15/15A are designed to be supplied by a start-up bleeder resistor and a dV/dt supply from the half-bridge circuit, or any other auxiliary supply derived from the half-bridge or the PFC. The supply current of the IC is low. An internal clamp limits the supply voltage. 2. Features and benefits Power factor correction features: Integrated 4-pin critical conduction mode PFC controller/driver Open and short pin-short protection on PFC feedback pin Overcurrent protection Overvoltage protection Half-bridge driver features: Integrated level-shifter for the high-side driver of the half-bridge Integrated bootstrap diode for the high-side driver supply of the half-bridge Independent non-overlap time Fluorescent lamp controller features: Linear dimming (UBA2016A and UBA2015A only) EOL (End-Of-Life) detection (both symmetrical and asymmetrical) Adjustable preheat time Adjustable preheat current Adjustable fixed frequency preheat (UBA2015 and UBA2015A only) Lamp ignition failure detection Ignition detection of all lamps fat multiple lamps with separate resonant tanks Second ignition attempt if first failed Constant output power independent of mains voltage variations Automatic restart after changing lamps Adjustable lamp current boost at start-up (UBA2016A only) Lamp current control UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver Enable input (UBA2015 and UBA2015A only) Protection Hard switching/capacitive mode protection Half-bridge overcurrent (coil saturation) protection Lamp overvoltage (lamp removal) protection Temperature protection 3. Applications Intended for fluorescent lamp ballasts with either a dimmable (UBA2016A and UBA2015A) or a fixed (UBA2015) output and PFC for AC mains voltages of up to 390 V. 4. Ordering information Table 1. Ordering information Type number Package Name Description Version UBA2016AT/N1 SO20 plastic small package outline package; 20 leads; body width 7.5 mm SOT163-1 UBA2015T/N1 SO20 plastic small package outline package; 20 leads; body width 7.5 mm SOT163-1 UBA2015AT/N1 SO20 plastic small package outline package; 20 leads; body width 7.5 mm SOT163-1 UBA2016AP/N1 DIP20 plastic dual in-line package; 20 leads; (300 mil) SOT146-1 UBA2015P/N1 DIP20 plastic dual in-line package; 20 leads; (300 mil) SOT146-1 UBA2015AP/N1 DIP20 plastic dual in-line package; 20 leads; (300 mil) SOT146-1 Table 2. UBA2016A_15_15A Objective data sheet Functional selection Type PFC dim Boost fixed frequency preheat UBA2016A yes yes yes no UBA2015 yes no no yes UBA2015A yes yes no yes All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 2 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver 5. Block diagram UBA2016A VDD 5 μA GATE DRIVE 14 GPFC SUPPLY AND REFERENCES 5 IREF DEMAG 0.1 V AUXPFC 13 OVPFC TEMPERATURE SENSE 1.39 V FBPFCOK PFC CONTROLLER 1V S 140 °C R 80 °C Q PFCOSP 0.25 V 16 VDD PFCOK FBPFC 11 1 mA ton TIMER 1.27 V 13.4 V restart COMPPFC 12 19 FSHB IC off EOL 3 brownout 3.0 V OR UVLO on: > 12.4 V off: < 10.0 V end of life LEVEL SHIFTER HIGH-SIDE GATE DRIVE 20 GHHB 18 SHHB 2x 16 μA HARD SWITCHING/ CAPACITIVE MODE DETECTION OVextra 5 μA 3.35 V NON OVERLAP OV FLUORESCENT LAMP CONTROLLER 2.5 V ign VFB 4 1V 0.5 V 8.5 μA 1 SLHB OCburn 2.5 V 2.6 μA 17 GLHB VDD OCpreheat VFBlow 80 mV LOW-SIDE GATE DRIVE LAMP ON DETECTION TIMER 8 CPT 10 BOOST VCO 100 μA overcurrent 1V 3V IFB 2 0.5 V 60 kΩ 9 μA 9 μA not burn 5V 1.27 V 5V 26 μA 5V 47 μA 9 DIM Fig 1. 6 CIFB 7 CF 001aam531 Block diagram UBA2016A UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 3 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver VDD UBA2015 UBA2015A 5 μA GATE DRIVE 14 GPFC SUPPLY AND REFERENCES 5 IREF DEMAG 0.1 V AUXPFC 13 OVPFC TEMPERATURE SENSE 1.39 V FBPFCOK PFC CONTROLLER 1V S 140 °C R 80 °C Q PFCOSP 0.25 V 16 VDD PFCOK FBPFC 11 1 mA ton TIMER 1.27 V 13.4 V restart COMPPFC 12 19 FSHB IC off EOL 3 brownout 3.0 V OR UVLO on: > 12.4 V off: < 10.0 V end of life LEVEL SHIFTER HIGH-SIDE GATE DRIVE 20 GHHB 18 SHHB 2x 16 μA HARD SWITCHING/ CAPACITIVE MODE DETECTION OVextra 5 μA 3.35 V NON OVERLAP OV LOW-SIDE GATE DRIVE 2.5 V VDD FLUORESCENT LAMP CONTROLLER ign VFB 4 1V OCpreheat VFBlow 80 mV 0.5 V 8.5 μA 1 SLHB OCburn 2.5 V 2.6 μA 17 GLHB LAMP ON DETECTION TIMER FIXED FREQUENCY PREHEAT VCO 8 CPT 10 PH/EN 100 μA overcurrent 1V 3V IFB 2 0.5 V 9 μA 9 μA 60 kΩ not burn 5V 1.27 V 5V 26 μA 5V 47 μA 0.25 V 9(1) DIM 6 CIFB 7 CF 001aan208 (1) Pin 9 is not connected in the UBA2015. Fig 2. Block diagram UBA2015A and UBA2015 UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 4 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver 6. Pinning information 6.1 Pinning SLHB 1 20 GHHB SLHB 1 20 GHHB IFB 2 19 FSHB IFB 2 19 FSHB EOL 3 18 SHHB EOL 3 18 SHHB VFB 4 17 GLHB VFB 4 17 GLHB IREF 5 16 VDD IREF 5 CIFB 6 15 GND CIFB 6 CF 7 14 GPFC CF 7 14 GPFC CPT 8 13 AUXPFC CPT 8 13 AUXPFC DIM 9 12 COMPPFC n.c. 9 12 COMPPFC UBA2016A BOOST 10 11 FBPFC UBA2015 PH/EN 10 15 GND 11 FBPFC 001aam532 Fig 3. 16 VDD 001aan200 Pin configuration UBA2016A Fig 4. Pin configuration UBA2015 SLHB 1 20 GHHB IFB 2 19 FSHB EOL 3 18 SHHB VFB 4 17 GLHB IREF 5 CIFB 6 CF 7 14 GPFC CPT 8 13 AUXPFC DIM 9 12 COMPPFC UBA2015A PH/EN 10 16 VDD 15 GND 11 FBPFC 001aan199 Fig 5. Pin configuration UBA2015A 6.2 Pin description Table 3. UBA2016A_15_15A Objective data sheet Pin description Symbol Pin Description SLHB 1 half-bridge (HB) low-side switch current sense input IFB 2 lamp current feedback input EOL 3 end-of-life sensing input VFB 4 lamp voltage feedback input IREF 5 reference current setting CIFB 6 lamp current feedback compensation CF 7 high frequency (HF) oscillator timing capacitor CPT 8 preheat and fault timing capacitor DIM 9 dimming function input UBA2016A and UBA2015A n.c. 9 UBA2015 All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 5 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver Table 3. Pin description …continued Symbol Pin Description BOOST 10 boost function input UBA2016A PH/EN 10 preheat frequency setting combined with enable UBA2015 and UBA2015A FBPFC 11 PFC feedback input COMPPFC 12 PFC output voltage feedback compensation AUXPFC 13 PFC auxiliary winding input GPFC 14 PFC gate driver output GND 15 ground VDD 16 supply GLHB 17 HB low-side switch gate driver output SHHB 18 HB high-side source connection FSHB 19 HB floating supply connection GHHB 20 HB high-side switch gate driver output 7. Functional description 7.1 Introduction The UBA2016A/15/15A is an integrated circuit for electronically ballasted fluorescent lamps. It provides a critical conduction mode Power Factor Correction (PFC) controller/driver and a half-bridge controller/driver with all the necessary functions for correct preheat, ignition and on-state operation of the lamp. Several protection mechanisms are incorporated to ensure the safe operation of the fluorescent lamp or a shut down of the complete ballast under any abnormal operating conditions or lamp failure. 7.2 Power Factor Correction (PFC) The PFC is a boundary conduction mode, on-time controlled system. The basic application diagram can be found in Figure 6. This type of PFC operates at the boundary between continuous and discontinuous mode. Energy is stored in the inductor LPFC each period that switch QPFC is on. When the input current Ii(PFC) is zero at the moment that QPFC is switched on, the amplitude of the current build up in LPFC will be proportional to Vi(PFC) and the time ton(PFC) that QPFC is on. This current continues to flow as output current Io(PFC) via DPFC into CBUS after QPFC is switched off. In this phase Io(PFC) is equal to Ii(PFC). A new cycle is started when Io(PFC) reaches zero. Ii(PFC) consists of a sequence of triangular pulses, each having an amplitude proportional to the input voltage and ton(PFC). If ton(PFC) is kept constant, the first harmonic of the input current is proportional to the input voltage. The PFC output voltage Vo(PFC) is controlled by ton(PFC). As ton(PFC) is more slowly regulated than the mains frequency it will not disturb the power factor. UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 6 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver Dbypass VDSRmains Vo(PFC) DPFC li(PFC) LPFC lo(PFC) Iswitch(PFC) R1 QPFC CBUS mains R3 R2 GPFC FBPFC AUXPFC C1 C2 COMPPFC UBA2016A UBA2015 UBA2015A VDD R4 GND 001aam533 Fig 6. Basic PFC application diagram 7.2.1 Regulation loop The control loop senses the PFC output voltage via resistors R1, R2 and the feedback input FBPFC. The frequency compensation network C1, C2 and R4 sets the response time and stability of the loop. The voltage at pin FBPFC is regulated to Vreg(FBPFC). When voltage on pin FBPFC is above the regulation voltage, pin COMPPFC is charged and when voltage on pin FBPFC is lower, pin COMPPFC is discharged. Current flow through pin COMPPFC is controlled by the PFC Operational Transconductance Amplifier (OTA) and its transconductance gm(PFC). The voltage on pin COMPPFC controls the PFC on-time, ton(PFC). So when the voltage at pin FBPFC is too high, ton(PFC) is reduced and less energy is transferred. When voltage at pin FBPFC is too low, ton(PFC) is increased and more energy is transferred. The voltage on pin FBPFC is sampled at the rising edge of pin GPFC and held internally during the leading edge blanking time tleb(FBPPC) before going to the OTA to prevent disturbance of the regulation level due to transition effects when the PFC external power switch is turned on The maximum ton(PFC) is set when the voltage at pin COMPPFC is clamped to Vclamp(COMPPFC) to limit the dead time in recovering regulation after a regulation range overshoot. The ton(PFC) time can be regulated down to zero. The moment at which the gate is turned on is determined by pin AUXPFC. When this pin is below demagnetization detection voltage Vdet(demag)AUXPFC and the low PFC off-time toff(PFC)low timer is finished, the next cycle starts. During start-up, the capacitor connected to pin COMPPFC is connected by an internal switch to pin FBPFC which allows it to partially charge before the PFC starts. This reduces the start-up time. UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 7 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver 7.2.2 Protection The PFC incorporates the following protection mechanisms: • When voltage on pin FBPFC drops below open/short protection threshold voltage Vth(osp)(FBPFC), the gate is turned off and the start of a new cycle is inhibited. A small internal filter prevents this protection reacting to a negative spike. • When pin FBPFC is left open, a pull-down bias current Ibias(FBPFC) ensures that the pin voltage drops below Vth(osp)(FBPFC). • When voltage at pin FBPFC rises above overvoltage threshold voltage Vth(ov)(FBPFC) the gate immediately turns off. A new cycle will not start while VFBPFC remains above Vth(ov)(FBPFC). This limits the PFC output voltage. This protection is disabled during the leading edge blanking time tleb(FBPFC) after GPFC goes high. • When the toff(PFC)low timer sequence has ended with no demagnetization detected (VAUXPFC has not risen above Vdet(demag)) the on-time of the next cycle will be the no demagnetization detected PFC on-time ton(PFC)nodemag to prevent excessive current build up in the coil. • Bias current Ibias(AUXPFC) ensures that pin AUXPFC is HIGH when not connected ensuring pin GPFC stays LOW. 7.3 Half-bridge driver The IC incorporates drivers for the half-bridge switches and all related circuits such as non-overlap, high voltage level shifter, bootstrap circuit for the floating supply and hard switching and capacitive mode detection. The UBA2016A/15/15A is designed to drive a half-bridge inverter with an inductive load. The load consists typically of an inductor with a resonant capacitor and a TL or CFL. A basic half-bridge application circuit driving a TL is shown in Figure 7 which also shows a typical IC supply configuration with a start-up bleeder resistor and a dV/dt supply. VBUS VDD GHHB UBA2016A UBA2015 UBA2015A SHHB FSHB GLHB GND 001aam534 Fig 7. UBA2016A_15_15A Objective data sheet Basic half-bridge and IC supply connection diagram All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 8 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver 7.3.1 VDD supply The UBA2016A/15/15A is intended to be supplied by a start-up bleeder resistor connected between the bus voltage VBUS and VDD and a dV/dt supply from the half-bridge point at pin SHHB. The IC starts up when the voltage at pin VDD rises above start-up voltage Vstartup(VDD) and locks out (stops oscillating) when the voltage at pin VDD drops below stop voltage Vstop(VDD). The hysteresis between the start and stop levels allows the IC to be supplied by a buffer capacitor until the dV/dt supply is settled. The UBA2016A/15/15A has an internal VDD clamp. This is an internal active Zener (or shunt regulator) that limits the voltage on the VDD supply pin to clamp voltage Vclamp(VDD). No external Zener diode is needed in the dV/dt supply circuit if the maximum current of the dV/dt supply minus the current consumption of the IC (mainly determined by the gate drivers’ load) is below Iclamp(VDD). 7.3.2 Low- and high-side drivers The low- and high-side drivers are identical. The output of each driver is connected to the equivalent gate of an external power MOSFET. The high-side driver is supplied by the bootstrap capacitor, which is charged from the VDD supply voltage via an internal diode when the low-side power MOSFET is on. The low-side driver is directly supplied by the VDD supply voltage. 7.3.3 Non-overlap During each transition between the two states GLHB HIGH/GHHB LOW and GLHB LOW/GHHB HIGH, GLHB and GHHB will both be LOW for a fixed non-overlap time tno to allow the half-bridge point to be charged or discharged by the load current (assuming the load always has an inductive behavior), and enabling zero voltage switching; see Figure 8. UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 9 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver tno VCF time 0 VSHHB + VVDD VGHHB VSHHB time VVDD VGLHB time 0 VBUS VSHHB time 0 001aam537 Fig 8. Oscillator, driver and half-bridge voltages 7.4 Fluorescent lamp control The IC incorporates all the regulation and control needed for the fluorescent lamp(s), such as filament preheat, ignition frequency sweep, lamp voltage limitation, lamp current control, start-up boost, dimming, end-of-life detection, overcurrent protection and hard switching limiting. In the UBA2016A/15/15A, 7 different operating states can be distinguished. In each state the IC acts in a specific way, as described in the next paragraphs. Figure 9 shows the possible transitions between the states with their conditions. UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 10 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver Power on reset OR disable GLHB AND (reset OR disable) Supply voltage definitions reset = (VDD < Vrst(VDD)) restart = (VDD < Vrestart(VDD)) VDD low = (VDD < Vstop(VDD)) VDD high = (VDD > Vstartup(VDD)) Reset state GLHB low stop latch and ignition attempt counter are reset reset NOT(reset) Stop state GLHB low GLHB AND (VDD low OR overtemp) Standby state GLHB high Auto-restart state GLHB low restart Non oscillating states (IC is off) Low power consumption GHHB and GPFC low VDD high AND enable AND NOT(overtemp) Oscillating states (IC is on) fast fault Preheat state BOOST and EOL disabled frequency is decreased until HB preheat current or the set value for the preheat frequency (UBA2015(A) only) is reached fault timeout AND (ignition attempts = 1) Preheat time completed fault timeout AND (ignition attempts = 2) Ignition state BOOST and EOL disabled frequency is decreased as long as no lamp overvoltage or HB overcurrent or hardswitching(1) is detected (1)(UBA2016(A) only) f low OR ignition detected fault timeout Burn state ignition attempt counter is reset BOOST function enabled EOL protection enabled Frequency determined by lamp current regulation loop fault definitions: overtemp = {set} T > Tth(act)otp {reset} T < Tth(rel)otp fast fault = over voltage extra OR capacitive mode(1) OR (over current lamp AND f high) coil saturation(2) slow fault = CPT low OR VFB low OR NOT(PFC OK) OR over voltage OR (over voltage end of life AND NOT (deep dimming))(2) OR coil saturation OR hardswitching OR brownout OR asymetrical end of life(2) the fault timer is started by slow fault and runs as long as slow fault continues. NOT(slow fault) resets the fault timer. Other definitions: enable = (VFFPRHT > Vth(en)(FFPRHT)) disable = NOT(enable) ignition detected = (VIFB > Vth(lod)(IFB)) AND (VVFB < Vth(lod)(VFB)) (1)(except for UBA2016A in IGNITION state after ZVS has been seen) (2)(BURN state only) 001aam538 Fig 9. State diagram UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 11 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver 7.4.1 Reset When voltage on pin VDD is below the reset voltage Vrst(VDD), both gates of the half-bridge driver are LOW. All internal latches are reset. When voltage on pin VDD rises above Vrst(VDD), the IC will enter STANDBY state. 7.4.2 Standby In STANDBY state the low-side gate driver is on (GLHB is HIGH).The floating supply capacitor CFSHB is then charged. When the VDD voltage rises above Vstartup(VDD), the Preheat state is entered. 7.4.3 Oscillating states (Preheat, Ignition and Burn) The highest and lowest oscillation frequency can be set with capacitor CCF connected to the CF pin. The oscillator is implemented in such a way that the lowest frequency fsw(low) is the most accurate. In any oscillating state (Preheat, Ignition or Burn), when VDD voltage drops below Vstop(VDD) or overtemperature is detected, the half-bridge stops oscillation when GLHB is HIGH and enters the STANDBY state. 7.4.4 Preheat The oscillating frequency starts at fsw(high) (see Figure 10 “Resonance curve application with UBA2015A” or Figure 11 “Resonance curve application with UBA2016A” point A) and remains at that frequency until the PFC output is sufficient (the voltage at pin FBPFC rises above the PFC voltage OK threshold voltage on pin FBPFC, Vth(VPFCok)FBPFC) and the voltages at pins CPT and VFB settle above their pin short protection levels (VVFB > Vth(osp)(VFB) and VCPT > Vth(scp)(CPT)). The half-bridge current is regulated when in the Preheat state; see Figure 10 “Resonance curve application with UBA2015A” or Figure 11 “Resonance curve application with UBA2016A” point B. Pin CIFB supplies a current Ich(CIFB) to the externally connected compensation network on this pin and its voltage will rise. This will cause the switching frequency to decrease (pin CIFB is the input for the voltage controlled oscillator). This will cause an increase in half-bridge current (assuming the switching frequency is higher than the load resonance frequency). This current is measured via pin SLHB using a resistor connected between the source of the low-side switch and ground. When the voltage on pin SLHB rises above the preheat current control voltage Vcrtl(ph)SLHB, discharge current Idch(CIFB) to pin CIFB and the frequency is increased. When the voltage drops below Vth(ocp)SLHB, current Ich(CIFB) from pin CIFB causes the frequency to decrease. UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 12 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver (1)V lamp (1) (2)I lamp (2) C Vign E D Ilamp(nominal) B A H fsw(reg) fsw(low) fsw(dim) fsw(ign) fsw(ph) f fsw(high) 001aan202 (1) Lamp voltage when lamp is off (not ignited yet). (2) Lamp current when lamp is on. Fig 10. Resonance curve application with UBA2015A (1)Vlamp (1) (2)I lamp (2) G C Vign F E D Ilamp(nominal) B H fsw(bst)(reg) fsw(bst)(low) fsw(low) fsw(reg) fsw(dim) fsw(ign) fsw(ph) A fsw(high) f 001aan204 (1) Lamp voltage when lamp is off (not ignited yet). (2) Lamp current when lamp is on. Fig 11. Resonance curve application with UBA2016A UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 13 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver The preheat frequency for UBA2015 and UBA2015A can also be regulated via pin PH/EN. UBA2015 and UBA2015A support current controlled preheat and fixed frequency preheat. During preheat the output voltage of pin PH/EN is Vph(PH/EN). The output current that an external resistor Rext(PH/EN) connected to this pin sinks is compared to 4⁄5 of the output current of the VCO (the current at pin CF with no fault condition present and the capacitor at that pin being charged minus the same current at fsw(low)). As long as the output current of the VCO is bigger the frequency is being decreased (by charging pin CIFB with Ich(CIFB)). If the current through the external resistor is bigger the frequency will be increased (by discharging pin CIFB with Idch(CIFB)). Current and fixed frequency control mechanisms are active at the same time. For fixed frequency preheat using pin PH/EN, the half-bridge current sense resistor connected to pin SLHB should be small enough not the activate the current control mechanism. If current controlled preheat is used, pin PH/EN should be left open (except of course for the open collector or open drain that drives the enable function). The preheat time tto(ph) can be set with capacitor CCPT on pin CPT. 7.4.5 Ignition After the Preheat state the IC enters the Ignition state. During the Ignition state the switching frequency is decreased by charging pin CIFB with Ich(CIFB). This will result in increasing lamp voltage until the lamp ignites (see point C in Figure 10 “Resonance curve application with UBA2015A” or Figure 11 “Resonance curve application with UBA2016A”) and lamp-on or fsw(low) (lowest frequency) is detected. Lamp-on detection occurs when the average absolute voltage on pin IFB is above lamp-on detection threshold Vth(lod)(IFB) and the voltage on pin VFB is more then 50 % of each clock cycle below the lamp-on detection threshold Vth(lod)(VFB) and after a delay td(lod). If either saturation, overvoltage or hard switching regulation (UBA2016A only) is triggered it will overrule the frequency sweep down and hold the frequency at the border where the fault appeared and start the fault timer. When the fault timeout tto(fault) is reached the IC enters Auto-restart state if it was the first ignition attempt, otherwise it will go to the Stop state; see Figure 9 “State diagram”. 7.4.6 Auto-restart The Auto-restart state is entered after a fault time out in the Ignition state during the first ignition attempt. See Figure 9 “State diagram”. When the IC is in Auto-restart state, it draws supply current Irestart(VDD). This will slowly discharge the buffer capacitor on pin VDD until the voltage on this pin drops below Vrestart(VDD). The IC then enters the Standby state. Here the VDD capacitor will be charged again to start a second ignition attempt. The bleeder current must be between standby current Istb(VDD) and Irestart(VDD). A time delay can be set between the two ignition attempts with the capacitor at pin VDD to reduce stress on the HB components. 7.4.7 Burn In Burn state the lamp current regulation and all protection circuits are active. The boost function (available in UBA2016A only) is also enabled. UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 14 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver 7.4.7.1 Lamp current control and dimming The AC lamp current is sensed by an external resistor connected to pin IFB. The resulting AC voltage on pin IFB is internally Double-Side Rectified (DSR), and compared to a reference level by an OTA. This reference level is determined by the internal reference regulation level Vreg(ref) and the voltage on the DIM input (UBA2015A and UBA2016A only), as shown in Figure 12 “Lamp current control”. Definition: the regulation voltage on pin IFB (Vreg(IFB)) is the level seen from outside the IC to which the IC will try to regulate the average absolute voltage on pin IFB. If the DIM input is not present or not connected or VDIM > Vreg(ref) then Vreg(IFB) is Vreg(ref) + non-idealities from the OTA and the DSR else Vreg(IFB) = VDIM + non-idealities from OTA and DSR. For the UBA2016A Vreg(IFB) also depends on the input current on pin BOOST (IBOOST). The boost current is multiplied and added to the OTA output current which translates to an extra voltage being added to Vreg(ref). See Section 7.4.7.3 “Boost” for further detail about the boost function. For the remainder of this Section we will assume IBOOST = 0. For the UBA2015A and UBA2016A the DIM input controls the lamp current set point. The DIM input level is internally clamped to Vreg(ref). The lowest possible DIM input level is set by the bias current on pin DIM Ibias(DIM) and the external resistance on the pin. If no dimming is required, pin DIM can be left open or connected via a capacitor to ground. The internal current source Ibias(DIM) will then charge the pin until it is internally clamped to Vreg(ref). UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 15 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver DOUBLE SIDE RECTIFIER Ilamp OTA VDD gm(IFB) CIFB IFB Cext(CIFB) Rext(IFB) Ri(IFB) VOLTAGE CONTROLLED OSCILLATOR VDD VDD Ibias(DIM) DIM Vreg(ref) VDD Ich(low)(CF) VDD IBOOST 1 3.5 1 7.8 VOLTAGE CONTROLLED CURRENT SOURCE BOOST Vhigh(CF) 1 ÷2 grey circuit parts are not present in some types CF clock 001aan205 Cext(CF) Fig 12. Lamp current control The output of the OTA is connected to pin CIFB. The external capacitor Cext(CIFB) is charged and discharged according to the voltage on the OTA inputs and the transconductance of the OTA, gm(IFB) according to the formula: ICIFB = gm(IFB) × (VIFB − Vreg(IFB). More components can be connected to pin CIFB to improve the response time and stability of the lamp current control loop. Pin CIFB is connected to the input of the VCO (Voltage Controlled Oscillator) that determines the frequency of the IC. Pin CIFB voltage is inversely proportional to the switching frequency. When the load is inductive, an increase in frequency decreases the lamp current, and a decrease in frequency increases the lamp current. With the closed loop for the lamp current in place, the IC will regulate to the required frequency for the desired lamp current. So when the IC enters Burn state it will go to either point D or H shown in Figure 10 (UBA2015A) or Figure 11 (UBA2016A) depending on the DIM input voltage. UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 16 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver However, the switching frequency can never go below fsw(low) (unless for UBA2016A when the boost function is active, see Section 7.4.7.3). If the regulation level is not reached at fsw(low) the IC will stay at fsw(low) (point E in Figure 10 and Figure 11). 7.4.7.2 Operation without lamp current control To operate the lamp without current control the lamp current sense pin IFB must be connected to ground. The lamp now operates at the lowest frequency fsw(low) (point E in Figure 10 or Figure 11). Dimming is not supported in this case. 7.4.7.3 Boost The boost feature is available only in the UBA2016A to support shorter run up times. The boost function changes the half-bridge switching frequency by lowering the lowest possible switching frequency from fsw(low) to fsw(bst)(low) and increasing the lamp current set point Vreg(IFB) by adding a multiple of the boost current to the OTA output current which translates to an extra voltage being added to Vreg(ref). During boost time, the frequency is lowered, and as a consequence of the inductive load the lamp current is increased. The implementation of the boost function is shown in Figure 12 “Lamp current control”. The boost input is a current input with an input range of 0 to Isat(BOOST). The input current is internally clamped at Isat(BOOST). If the input current at the pin is above Isat(BOOST) the effect will not become bigger. The voltage on the pin is determined by the voltage drop across the internal current mirror input and limited by an internal clamp circuit if the input current at the pin rises above Isat(BOOST). For maximum current allowed into the pin; see Table 4. An example of how boost function can be implemented is shown in Figure 13. Vo(PFC) Rhv CBUS UBA2016A Chv RBOOST Dreset Cboost BOOST Rbias 001aam539 Fig 13. Boost application example; UBA2016A The boost current is determined by resistor RBOOST. Rbias provides a small threshold for the boost function and with capacitor CBOOST keeps the BOOST pin at a defined (inactive) level (0 V) during normal lamp operation (after the boost period). The boost time constant is reflected by the sum of capacitors Chv and CBOOST and RBOOST. Resistor Rhv and capacitor CBOOST filter out the ripple on Vo(PFC). An example of component values for Vo(PFC) = 430 V is: Rhv = 22 MΩ (500 V); Chv = 100 nF (500 V); Dreset = 1N4148; CBOOST = 150 nF (63 V); RBOOST = 10 MΩ and Rbias = 10 MΩ. UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 17 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver The amount of boost depends on the current into the BOOST pin and the lamp current control. If the application does not use lamp current control, the switching frequency will go down to the lowest possible boost switching frequency fsw(bst)(low) (point G in Figure 11 “Resonance curve application with UBA2016A”) that is determined by Equation 1 or Equation 2, depending on the value of IBOOST. 0 ≤ I BOOST ≤ I sat ( BOOST ) → f sw ( bst ) ( low ) = f sw ( low ) ( 1 – I BOOST ⋅ N f ( bst ) ( low ) ) (1) I BOOST > I sat ( BOOST ) → f sw ( bst ) ( low ) = f sw ( low ) ( 1 – I sat ( BOOST ) ⋅ N f ( bst ) ( low ) ) (2) If the application uses lamp current control, the switching frequency is regulated to boost regulation voltage on pin IFB, Vreg(bst)(IFB) (point F in Figure 11 “Resonance curve application with UBA2016A”) that can be calculated by Equation 3 or Equation 4, (depending on the value of IBOOST) if the switching frequency remains above fsw(bst)(low), otherwise the switching frequency is fsw(bst)(low); see Equation 1 or Equation 2. 0 ≤ I BOOST ≤ I sat ( BOOST ) → V reg ( IFB ) ( I BOOST ) = V reg ( IFB ) ( 1 + I BOOST ⋅ N l ( bst )reg ) (3) I BOOST > I sat ( BOOST ) → V reg ( bst ) ( IFB ) = V reg ( IFB ) + I sat ( BOOST ) ⋅ N Vreg ( bst ) (4) 7.4.8 Stop state When in Stop state the IC is off and all driver outputs are low. The IC will remain in Stop state until the voltage on pin VDD drops below Vrst(VDD) or it is disabled, in which case it will go to Reset state. The sequence of events for entering the Stop state are shown in Figure 9 “State diagram”. 7.5 Enable and Disable The enable function is only available in the UBA2015 and UBA2015A and works via pin PH/EN. If this pin is pulled below the enable voltage Ven(PH/EN) then the IC goes into the Standby state (immediately if GLHB is high, otherwise it will continue its normal clock cycle until GLHB is high and then go to the Standby state). The external interface with pin PH/EN for the enable signal should be an open collector or open drain type driver. To enable the IC the open collector or open drain should be open (high ohmic) to not disturb the fixed frequency preheat setting function of pin PH/EN. In Restart, Standby and Stop states the standby pull-up current source Ipu(stb)(PH/EN) will pull the voltage at pin PH/EN above Ven(PH/EN). In Preheat, Ignition and Burn states the normal output voltage driver of the IC will pull the pin high. In those cases the external driver must draw a current Iclamp(PH/EN) from the pin to disable the IC. 7.6 Protection circuits 7.6.1 End-of-life rectifying lamp detection If voltage on pin EOL is below low threshold voltage Vth(low)EOL or above Vth(high)EOL the fault timer will start. These threshold voltage levels are related to pin FBPFC voltage according to the formula: Vth(low)EOL = VFBPFC = Vth(high)EOL / 2. The FBPFC voltage is sampled during GPFC low and hold during GPFC high periods to prevent disturbance of the EOL levels due to the switching of the PFC. UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 18 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver A programmable end-of-life window is achieved by the internal bias current sink Ibias(EOL). The effective relative size of the EOL window will decrease in line with the increasing series resistance connected to pin EOL. The end-of-life lamp rectifying detection is only active during the Burn state. 7.6.2 End-of-life overvoltage detection This protection is intended to protect against symmetrical lamp aging. When in Burn state the voltage on pin VFB exceeds the overvoltage end-of-life threshold voltage Vth(oveol)(VFB) by more then 50 % of each switching cycle the fault timer will start. Vth(oveol)(VFB) is related to the regulation voltage on pin IFB Vreg(IFB) that itself is dependent on the voltage on pin DIM (see Section 7.4.7.1 “Lamp current control and dimming”) according to the formula: Vth(oveol)(VFB) = a − b × Vreg(IFB) Parameters a and b can be calculated from the Vth(oveol)(VFB) values given in Table 6. The end-of-life overvoltage protection is only active during Burn state and (for UBA2015A and UBA2016A) if the voltage at pin DIM is above the overvoltage end-of-life enable voltage Ven(oveol)(DIM). 7.6.3 Capacitive mode detection Under all normal operating conditions the half-bridge switching frequency should be higher than the load resonance frequency. The load then shows an inductive behavior in that the load current Iload lags behind the half-bridge voltage VSHHB. If the amplitude and the phase difference are large enough, the load current will charge any capacitance on pin SHHB during the non-overlap time tno(LH), and discharge it during the other non-overlap time tno(HL). As a result the voltage across the switches is almost zero at the moment they turn on. This is called zero voltage switching; see Figure 14 “Switching”. Zero voltage switching provides the highest switching efficiency and the least Electromagnetic Emission (EME). Capacitive mode switching can occur when, due to any abnormal condition, the switching frequency is below the load resonance frequency. This can happen when the lamp is removed. The load current will then keep the backgate diode of the switch that is switched off conducting during the non-overlap time, and if the other switch is turned on, a sudden step of the half-bridge voltage to the other supply rail takes place (which causes huge current spikes). Also cross conduction between the switches can occur during the reverse recovery of the backgate diode. These effects put huge stress on the power switches, most of which can only handle capacitive mode switching a few times before they break down. To protect against capacitive mode switching the IC monitors pin SHHB during the non-overlap time tno(LH) between switching off of the low-side switch and switching on of the high-side switch. If a rise of VSHHB (dVSHHB/dt > Vth(cm)(SHHB)) during tno(LH) is not detected then the IC will conclude that capacitive mode switching is occurring during the next full cycle. If capacitive mode is detected longer than the fault activation delay time tdet(fault) then the IC will enter Stop state. Capacitive mode detection is active in all oscillating states for all ICs except in the Ignition state of the UBA2016A if zero voltage switching has been observed. In that case the UBA2016A switches to hard switching regulation, see Section 7.6.4 “Hard switching regulation (UBA2016A)”. UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 19 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver During ignition a situation may occur where the amplitude of the load current is high and the half-bridge is at the boundary of capacitive mode switching; see Figure 14 “Switching”. The load current crosses zero during the non-overlap time. If the amplitude of the load current is large enough, the UBA2015 and UBA2015A might not detect capacitive mode because VSHHB did rise before going down again. The backgate diode of one switch is conducting again when the other switch switches on. Since this can only happen if the load current crosses zero during the non-overlap time, the momentary value of the load current at the end of the non-overlap time will be not so big, and will not necessarily damage the switches. Depending on the topology used, the DC blocking capacitor might be charged via the lamp(s) at the moment the lamp(s) ignite. This will cause a temporary DC current addition to the load current that might be interpreted by the UBA2015 and UBA2015A as capacitive mode switching. If this happens the DC blocking capacitor must be reduced or pre-charged. The UBA2016A does not have this problem. 7.6.4 Hard switching regulation (UBA2016A) In Ignition state the UBA2016A capacitive mode detection is disabled and replaced by hard switching regulation. This enables ignition without voltage feedback. The hard switching regulation measures the voltage step on pin SHHB at the end of the non-overlap time tno(LH) (Vstep(SHHB) in Figure 14 “Switching”) and increases the switching frequency by discharging pin CIFB with a current according to the formula: Idch(hswr)CIFB = (Vstep(SHHB) − Vth(hswr)SHHB) × gm(hswr) In this way the IC keeps the switching frequency during ignition at the point where there is still a small phase difference between the load current and the half-bridge voltage, and the switching losses due to hard switching are limited. This is assuming that it is not already held at the higher frequency by the overvoltage protection or coil saturation protection. As Figure 14 “Switching” shows, hard switching also occurs when the amplitude of the load current is to small. This might happen when the IC enters Ignition state at the end of preheat and the frequency is still relatively high. To prevent the IC from getting stuck at fhigh the hard switching regulation is disabled until zero voltage switching has been observed, that is if Vstep(SHHB) < Vth(zvs)SHHB. 7.6.5 Hard switching protection The hard switching level Vstep(SHHB) step is measured via pin SHHB. The hard switching level is determined by measuring the voltage step on pin SHHB on the rising edge of pin GHHB; see Figure 14 “Switching”. When Vstep(SHHB) is above the hard switching protection threshold voltage on pin SHHB (Vth(hswp)SHHB) the fault timer is activated. UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 20 of 42 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx NXP Semiconductors UBA2016A_15_15A Objective data sheet VFSHB HV VGHHB VSHHB GHHB tno(LH) high side switch tno(HL) VDD SHHB VGLHB Iload GND SENSE Rev. 1 — 20 May 2011 GLHB Vstep(SHHB) low side switch VSHHB GND GND zero voltage switching hard switching (due to small phase difference between VSHHB and iload) 0 boundary of capacitive mode switching capacitive mode switching 21 of 42 © NXP B.V. 2011. All rights reserved. 001aan209 Fig 14. Switching 600 V fluorescent lamp driver hard switching (due to small amplitude of iload) Iload UBA2016A/15/15A All information provided in this document is subject to legal disclaimers. VHV UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver 7.6.6 Coil saturation protection When the peak voltage on pin SLHB exceeds saturation threshold voltage Vth(sat)SLHB, an additional current Iadd(CF) is sourced to pin CF to shorten the running oscillator cycle. In Ignition state the fault timer is started and a discharge current Idch(CIFB) is drawn from pin CIFB during the next cycle to increase the switching frequency. In Burn state the IC will go to Stop state if coil saturation is detected longer than the saturation detection delay time td(det)sat. Current Ibias(SLHB) is sourced to pin SLHB which will force the controller into coil saturation protection if pin SLHB is left open. 7.6.7 Lamp overcurrent protection If voltage on pin IFB exceeds the overcurrent detection threshold voltage Vth(ocd)(IFB), and the oscillator is running at fsw(high), an overcurrent is detected and the IC will immediately enter the Stop state. 7.6.8 Lamp overvoltage protection When the peak voltage on pin VFB exceeds Vth(ov)(VFB), the fault timer is started and a discharge current Idch(CIFB) is drawn from pin CIFB during the next cycle to increase the switching frequency. When VVFB > Vth(ovextra)(VFB) for longer than the fault activation delay time tdet(fault) then the IC will enter the Stop state. 7.6.9 Lamp removal detection Removing the lamp from applications that have the resonant capacitor connected via the lamp filaments, will result in hard switching because current cannot flow through the ballast inductor. If hard switching is detected during Ignition or Burn state the fault timer will be started. For applications with the resonant capacitor connected directly to the ballast inductor, capacitive mode, coil saturation or over voltage will be detected. Capacitive mode is activated if the switching frequency ends up below the resonance frequency due to removal of the lamp. If the switching frequency is near or above the resonance frequency, the lamp (or rather the lamp socket) voltage and half-bridge current will be very high due to the unloaded resonant circuit (lamp inductor and lamp capacitor) which activates the coil saturation protection or the overvoltage protection. 7.6.10 Temperature protection When the temperature is above Tth(act)otp and GLHB is high, the IC enters Standby state. The IC cannot exit the Standby state until the temperature drops below Tth(rel)otp. 7.6.11 Fault timer Any fault that starts the fault timer must be detected for longer than the fault activation delay time td(act)fault to actually start the timer. When the timer is started, the capacitor at pin CPT is alternately being charged and discharged. After 8 charging and 7 discharging cycles the fault time-out period tto(fault) is reached and the IC enters either the Stop state or the Auto-restart state, depending on the fault detected, the current state of the timer and the number of ignition attempts; see Figure 9 “State diagram”. If the fault that started the UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 22 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver timer is no longer detected for a period longer than the fault release delay time td(rel)fault, the fault timer will be reset and at any new occurance of the fault, the timer will start from zero. Faults which activate the fault timer are shown as SlowFault in Figure 9 “State diagram”. The fault timer uses the same pin (CPT) to set the time with an external capacitor Cext(CPT) as the preheat timer. The ratio between the preheat time-out time tto(ph) and the fault time-out time tto(fault) can be changed by adding an external series resistor Rs(ext)(CPT) or an external parallel resistor Rp(ext)(CPT) to the external capacitor Cext(CPT); see Figure 15 “CPT connections”. CPT CPT CPT Rs(ext)(CPT) Cext(CPT) Rp(ext)(CPT) Cext(CPT) Cext(CPT) smaller ratio tto(ph)/tto(fault) default ratio tto(ph)/tto(fault) larger ratio tto(ph)/tto(fault) 001aan210 Fig 15. CPT connections The fault timer incorporates a protection that ensures safe operation conditions if the CPT pin voltage is below Vth(scp)(CPT) (shorted to GND) by holding the oscillation frequency at fsw(high). 7.6.12 Brownout protection Brownout protection is designed to maintain stable and safe lamp operation during dips in mains supply. Without this protection the current demand from the bus voltage to maintain constant lamp power would increase upon a drop in bus voltage. This creates an unstable situation with the mains input voltage dropping and the PFC reaching its regulation range limit. Brownout protection reduces the lamp power when the PFC is out of regulation. This situation is only allowed for a limited time to prevent excessive component stress. When the PFC is outside its regulation range and the bus voltage is still too low (VCOMPPFC = Vclamp(COMPPFC) and VFBPFC < Vreg(FBPFC)), a brownout current Ibo(CF) is added to the charge current at pin CF, thus increasing the fsw(low). A discharge brownout current Idch(bo)(CIFB) is also drawn from pin CIFB. Both Ibo(CF) and Idch(bo)(CIFB) are proportional to the difference between VFBPFC and Vreg(FBPFC). If VFBPFC < Vth(bo)(FBPFC) the fault timer will start. The start-up bleeder resistor and the regulation range of the PFC should be dimensioned in such a way that if the fault timer times out on brownout protection and the IC enters Stop state, the input mains voltage is too low to support the standby current of the IC via the bleeder resistor. The IC will then automatically reset and start-up in normal mode (and reignite the lamps) when the mains voltage has returned to normal. UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 23 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver 8. Limiting values Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). All voltages referenced to signal ground (GND pin 15); current flow into the IC is positive. Symbol Parameter Conditions Min Max Unit 30 36 kΩ −4 +4 V/ns General Rref(IREF) reference resistance on pin IREF SR slew rate Tamb ambient temperature −40 +125 °C Tj junction temperature −40 +150 °C Tstg storage temperature −55 +150 °C continuous 0 570 V t < 0.5 s 0 630 V with respect to VSHHB −0.3 +14 V with respect to VSHHB −0.3 +14 V pins FSHB, GHHB and SHHB Voltage VFSHB voltage on pin FSHB VGHHB voltage on pin GHHB VGLHB voltage on pin GLHB −0.3 +14 V VGPFC voltage on pin GPFC −0.3 +14 V VVDD voltage on pin VDD −0.3 +14 V VAUXPFC voltage on pin AUXPFC −9 +9 V VEOL voltage on pin EOL −9 +9 V VSLHB voltage on pin SLHB −9 +9 V VIFB voltage on pin IFB −5 +5 V VDIM voltage on pin DIM −0.1 +5 V VFBPFC voltage on pin FBPFC −0.1 +5 V VBOOST voltage on pin BOOST −0.3 +2.2 V VPH/EN voltage on pin PH/EN −0.1 +5 V VVFB voltage on pin VFB −0.1 +5 V IVDD current on pin VDD - 50 mA IEOL current on pin EOL −1 +1 mA ISLHB current on pin SLHB −1 +1 mA IBOOST current on pin BOOST −50 +50 μA IAUXPFC current on pin AUXPFC −1 +1 mA Current UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 24 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver Table 4. Limiting values …continued In accordance with the Absolute Maximum Rating System (IEC 60134). All voltages referenced to signal ground (GND pin 15); current flow into the IC is positive. Symbol Parameter Conditions Min Max Unit JEDEC Class 2 for pins: SLHB, IFB, EOL, CIFB, CPT, IREF, VFB, CF, DIM, BOOST, PH/EN, FBPFC, COMPPFC, AUXPFC, GPFC, VDD and GLHB −2 +2 kV JEDEC Class 1C for pins: GHHB, FSHB and SHHB −1 +1 kV JEDEC Class 2 for pins: SHHB, FSHB, GHHB −200 +200 V JEDEC Class 3 for pins: SLHB, IFB, EOL, VFB, IREF, CIFB, CF, CPT, DIM, BOOST, PH/EN, FBPFC, COMPPFC, AUXPFC, GPFC, VDD, GLHB −500 +500 V −100 +100 mA ElectroStatic Discharge (ESD) electrostatic discharge voltage VESD Human Body Model (HBM) Charge Device Model (CDM) Latch-up [1] [1] latch-up current Ilu Positive and negative latch-up currents tested at Tj = 150 °C by discharging a 22 μF capacitor though a 50 Ω series resistor with a 350 μH series inductor. Latch-up current values are in accordance with the general quality specification. 9. Thermal characteristics Table 5. Thermal characteristics Symbol Parameter Conditions Typ Unit Rth(j-a) thermal resistance from junction to ambient in free air; mounted on a single-sided PCB; SO20 package 100 K/W in free air; mounted on a single-sided PCB; DIP20 package 90 K/W 10. Characteristics Table 6. Characteristics Tamb = 25 °C; settings according to default setting[1]; all voltages referenced to GND; current flow into the IC is positive; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit leakage current VFSHB = 630 V; VGHHB = 630 V; VSHHB = 630 V; VVDD = 0 V - - 2 μA High voltage Ileak Start-up Vstartup(VDD) start-up voltage on pin VDD 11.9 12.4 12.9 V Vstop(VDD) stop voltage on pin VDD 9.6 10.0 10.4 V Vhys(VDD) hysteresis voltage on pin VDD 2.1 2.4 2.7 V Istb(VDD) standby current on pin VDD VVDD = 11.5 V 0.20 0.24 0.28 mA Ipu(stb)(PH/EN) standby pull-up current on pin PH/EN Standby or Stop state; VPH/EN = 0.25 V 7.7 9 10.3 μA Vrst(VDD) reset voltage on pin VDD 3.6 4.2 4.8 V UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 25 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver Table 6. Characteristics …continued Tamb = 25 °C; settings according to default setting[1]; all voltages referenced to GND; current flow into the IC is positive; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit Vrestart(VDD) restart voltage on pin VDD 6.2 6.5 6.8 V Irestart(VDD) restart current on pin VDD VVDD = 9 V 0.85 Vclamp(VDD) clamp voltage on pin VDD IC off; IVDD = 0.33 mA 13.0 1.10 1.35 mA 13.4 13.8 V Iclamp(VDD) clamp current on pin VDD IC off; VVDD = 14.0 V 25 45 - mA IVDD current on pin VDD VFBPFC = 1.2 V; VCOMPPFC = 1 V 1.2 1.7 2.2 mA PFC normal operation ton(PFC) PFC on-time VCOMPPFC = 350 mV 0.70 1.05 1.40 μs ton(PFC)high high PFC on-time VCOMPPFC = Vhigh(COMPPFC) 24 28 32 μs toff(PFC)low low PFC off-time 1.7 2.0 2.3 μs tleb(FBPFC) leading edge blanking time on pin FBPFC from the start of rising edge on pin GPFC 260 330 400 ns Vreg(FBPFC) regulation voltage on pin FBPFC VCOMPPFC = 1.6 V 1.23 1.27 1.31 V VCOMPPFC = 200 mV 1.23 1.28 1.33 V Ibias(FBPFC) bias current on pin FBPFC VFBPFC = 1.27 V 4.5 5.0 5.5 μA gm(PFC) PFC transconductance VCOMPPFC = 1.5 V; 1.2 V < VFBPFC < 1.34 V 25 30 35 μA/V 0.95 1.00 1.05 V Vth(VPFCok)FBPFC PFC voltage OK threshold voltage on pin FBPFC Vdet(demag) demagnetization detection voltage on pin AUXPFC 50 100 150 mV Vclamp(COMPPFC) clamp voltage on pin COMPPFC VFBPFC = 1 V 2.85 3.00 3.15 V PFC protection ton(PFC)nodemag no demagnetization detected PFC on-time 1.0 1.3 1.6 μs Vth(osp)(FBPFC) open/short protection threshold voltage on pin FBPFC 0.20 0.25 0.30 V Vth(ov)(FBPFC) overvoltage threshold voltage on pin FBPFC 1.34 1.39 1.43 V Ibias(AUXPFC) bias current on pin AUXPFC VAUXPFC = 0.1 V −6 −5 −4 μA Isource(GPFC) source current on pin GPFC VGPFC = 4 V; VVDD = 12 V −105 −90 −75 mA Rsink(GPFC) sink resistance on pin GPFC VGPFC = 2 V; VVDD = 12 V 13.5 16.0 18.5 Ω PFC driver HB preheat Rext(PH/EN) external resistor on pin PH/EN 38.6 - - kΩ tto(ph) preheat time-out time CCPT = 100 nF 0.80 0.94 1.08 s VO(ph)(PH/EN) preheat output voltage on pin PH/EN Preheat or Ignition state 1.78 1.84 1.90 V Vctrl(ph)SLHB overcurrent protection threshold voltage preheat on pin SLHB 0.44 0.48 0.52 V Ich(CIFB) charge current on pin CIFB −10.3 −9.0 −7.7 μA UBA2016A_15_15A Objective data sheet no fault detected; Preheat and Ignition states only; VCIFB = 1.5 V All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 26 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver Table 6. Characteristics …continued Tamb = 25 °C; settings according to default setting[1]; all voltages referenced to GND; current flow into the IC is positive; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit Idch(CIFB) discharge current on pin CIFB preheat overcurrent detected; VCIFB = 1.5 V 7.7 9.0 10.3 μA fsw(ph) preheat switching frequency UBA2015; UBA2015A Rext(PH/EN) = 40 kΩ; Cext(CF) = 200 pF 93 97.7 102.4 kHz Rext(PH/EN) = 100 kΩ; Cext(CF) = 200 pF 62 66 70 kHz HB lamp ignition fsw(high)/fsw(low) high switching frequency to low switching frequency ratio 2.2 2.4 2.6 Vfsw(low)(CIFB) low switching frequency voltage on pin CIFB - 3.0 - V Vth(lod)(IFB) lamp on detection threshold voltage on pin IFB 1.00 1.11 1.22 V Vth(lod)(VFB) lamp on detection threshold voltage on pin VFB 0.9 1.0 1.1 V V(Vreg−Vth(lod)) regulation voltage to lamp-on-detect threshold voltage difference 40 160 220 mV td(lod) lamp on detection delay time 2 3 4 ms 41 43 45 kHz 20 - 80 kHz - 2.5 - V VCIFB = 2 V; VIFB > 0 V 1.22 1.27 1.32 V VCIFB = 2 V; VDIM = 127 mV; VIFB > 0 V 77 127 177 mV VCIFB = 2 V; VIFB < 0 V −1.34 −1.27 −1.2 V VCIFB = 2 V; VDIM = 127 mV; VIFB < 0 V −197 −127 −57 mV pin IFB HB normal operation fsw(low) low switching frequency CCF = 200 pF Vhigh(CF) high voltage on pin CF Vreg(IFB) regulation voltage on pin IFB Ich(low)(CF) low charge current on pin CF - 47 - μA Vi(IFB) input voltage range on pin IFB VCIFB = 2 V −3.1 - +3.1 V Ri(IFB) input resistance on pin IFB VIFB = 1 V - 60 - kΩ VIFB = −1 V - 30 - kΩ Ven(PH/EN) enable voltage on pin PH/EN 0.21 0.25 0.29 V VO(burn)(PH/EN) burn state output voltage on pin PH/EN Burn state 1.21 1.27 1.33 V gm(IFB) IFB transconductance VCIFB = 2 V 14 16.5 19 μA/V IO(clamp)(PH/EN) output current clamp on pin PH/EN Preheat, Ignition or Burn states; VPH/EN = 0.2 V - - 0.16 mA Isource(GLHB) source current on pin GLHB VGLHB = 4 V −105 −90 −75 mA Rsink(GLHB) sink resistance on pin GLHB VGLHB = 2 V 13.5 16 18.5 Ω Isource(GHHB) source current on pin GHHB VSHHB = 0 V; VGHHB = 4 V −105 −90 −75 mA HB driver UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 27 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver Table 6. Characteristics …continued Tamb = 25 °C; settings according to default setting[1]; all voltages referenced to GND; current flow into the IC is positive; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit Rsink(GHHB) sink resistance on pin GHHB VSHHB = 0 V; VGHHB = 2 V 13.5 16 18.5 Ω tno non-overlap time 1.25 1.50 1.75 μs VFd(bs) bootstrap diode forward voltage IFS = 5 mA 1.0 1.5 2.0 V Ibias(DIM) bias current on pin DIM VDIM = 1 V −28 −26 −24 μA Ri(DIM) input resistance on pin DIM VDIM = 2.5 V - 30 - kΩ 2.35 2.50 2.65 V Dimming HB protection Vth(sat)(SLHB) saturation threshold voltage on pin SLHB td(det)sat saturation detection delay time tleb(SLHB) leading edge blanking time on pin SLHB Iadd(CF) additional current on pin CF Ibias(SLHB) bias current on pin SLHB Vth(ocd)(IFB) - 0.3 - μs 260 340 420 ns VSLHB > Vth(sat)SLHB; VCF = 2 V −107 −96 −85 μA VSLHB = 2.5 V −10 −8.5 −7 μA overcurrent detection threshold voltage on pin IFB 2.8 3.0 3.2 V Vth(osp)(VFB) open/short protection threshold voltage on pin VFB 40 80 120 mV Vth(ov)(VFB) overvoltage threshold voltage on pin VFB 2.4 2.5 2.6 V tdet(fault) fault detection time - 125 - μs - 50 - μs Burn state overvoltage extra or capacitive mode during burn state trel(fault) fault release time - 1 - ms Vth(ovextra)(VFB) overvoltage extra threshold voltage on pin VFB 3.2 3.35 3.5 V Ibias(VFB) bias current on pin VFB 2.3 2.6 2.9 μA Vth(low)EOL low threshold voltage on pin EOL VFBPFC = 1.27 V 1.21 1.27 1.33 V Vth(high)EOL high threshold voltage on pin EOL VFBPFC = 1.27 V 2.39 2.54 2.69 V Ibias(EOL) bias current on pin EOL VEOL = 1.9 V 15.2 16.0 16.8 μA Vth(oveol)(VFB) overvoltage end-of-life threshold voltage pin DIM open on pin VFB UBA2015A; UBA2016A 0.8 0.88 0.96 V 0.92 1.0 1.08 V VDIM = 1.0 V UBA2015A; UBA2016A 1.15 1.23 1.31 V Ven(oveol)(DIM) overvoltage end-of-life enable voltage on pin DIM UBA2015A; UBA2016A VDIM = 0.5 V 0.21 0.25 0.29 V Vth(hswp)SHHB hard switching protection threshold voltage on pin SHHB fsw = 50 kHz - 100 - V Vth(zvs)SHHB zero voltage switching detection threshold voltage on pin SHHB fsw = 50 kHz - 30 - V Vth(hswr)SHHB hard switching regulation threshold voltage on pin SHHB fsw = 50 kHz - 100 - V UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 28 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver Table 6. Characteristics …continued Tamb = 25 °C; settings according to default setting[1]; all voltages referenced to GND; current flow into the IC is positive; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit Vth(cm)SHHB capacitive mode detection threshold voltage on pin SHHB tno(LH) - 30 - V/μs gm(hswr) hard switching regulation transconductance UBA2016A; Ignition state - 18 - μA/V 80 120 160 mV hard switching step on pin SHHB above Vth(hswr)(SHHB) per extra volt step at fsw = 50 kHz Vth(scp)(CPT) short-circuit protection threshold voltage on pin CPT Rpar(ext)(CPT) external parallel resistance on pin CPT 700 - - kΩ Rs(ext)(CPT) external series resistance on pin CPT - - 40 kΩ tto(fault) fault time-out time 0.16 0.19 0.22 s tto(ph)/tto(fault) ratio between preheat time-out time and Rpar(ext) = 700 kΩ; fault time-out time Rs(ext) not connected (short) 3 3.4 3.8 Rpar(ext) not connected (open); Rs(ext) not connected (short) 4.7 5.2 5.7 Rpar(ext) not connected (open); Rs(ext) = 40 kΩ 9 11.5 14 VCOMPPFC = Vhigh(COMPPFC); VFBPFC = 1.0 V; VCF = 1.5 V 12 17 22 μA 10 30 50 mV 14 18 22 μA 21 24 27 kHz 0.14 0.165 0.19 1/μA 1.75 1.84 1.93 V CCPT = 100 nF Ibo(CF) brownout current on pin CF V(Vreg-Vth(bo)) regulation voltage to brownout threshold VCOMPPFC = Vhigh(COMPPFC) voltage difference on pin FBPFC Idch(bo)CIFB brownout discharge current on pin CIFB VCOMPPFC = Vhigh(COMPPFC); VFBPFC = 1.0 V; VCIFB = 2.0 V [2] Boost IBOOST ≥ Isat(BOOST); Cext(CF) = 200 pF fsw(bst)(low) low boost switching frequency Nf(bst)low low boost frequency constant Vreg(bst)(IFB) boost regulation voltage on pin IFB NVreg(bst) boost regulation voltage constant 0.180 0.21 0.24 V/μA Isat(BOOST) saturation current on pin BOOST 2.3 2.7 3.1 μA VBOOST voltage on pin BOOST IBOOST = 1 μA - 1 - V IBOOST = 5 μA - 1.4 - V IBOOST = 50 μA - - 2.2 V IBOOST ≥ Isat(BOOST) Temperature protection Tth(act)otp overtemperature protection activation threshold temperature 120 140 160 °C Tth(rel)otp overtemperature protection release threshold temperature 65 80 95 °C [1] Default setting; see Table 7. [2] The threshold for the brownout protection is slightly below the normal regulation level on pin FBPFC. The design guarantees that it will always be below this level because the clamp current from the PFC OTA is used as a signal. UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 29 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver Table 7. UBA2016A_15_15A Objective data sheet Default settings for characteristics Pin name Pin Application SLHB 1 connected to ground IFB 2 connected to ground EOL 3 connected to a 2 V test supply VFB 4 connected to a 2 V test supply IREF 5 connected via a 33 kΩ resistor to ground CIFB 6 connected via a 100 nF capacitor to ground CF 7 connected via a 200 pF C0G (NP0) capacitor to ground CPT 8 connected via a 100 nF capacitor to ground DIM 9 connected via a 100 pF capacitor to ground BOOST 10 connected to ground; UBA2016A PH/EN 10 not connected; UBA2015 and UBA2015A FBPFC 11 connected to a 1.27 V test supply COMPPFC 12 connected via a 100 nF capacitor to ground AUXPFC 13 connected to ground GPFC 14 not connected (open) GND 15 connected to ground VDD 16 connected to a 13 V test supply GLHB 17 not connected (open) SHHB 18 connected to ground FSHB 19 connected to a 13 V test supply GHHB 20 not connected (open) All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 30 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver 11. Application information 11.1 Connecting the IC in an application A 33 kΩ resistor must be connected between pin IREF and GND. The tolerance of this resistor adds to any current related tolerances of the IC, including fsw(low). No other components can be connected to pin IREF. Tolerance and temperature dependency of the capacitor connected between pin CF and GND will add to the tolerance on fsw(low). Small decoupling capacitors (about 100 pF) are recommended on pins FBPFC and IFB close to the IC. Normal sized decoupling capacitors (about 10 nF) are recommended on pins DIM and EOL. The capacitors at pins CF, COMPPFC, CPT, FSHB and VDD should also be placed close to the IC. A capacitor between pin CIFB and GND of at least 470 pF is needed for stability of the low switching frequency. A capacitor between pin VDD and GND of at least 10 nF is needed for stability of the internal VDD voltage clamp. However, for reliable operation of the IC a low ESR type of at least 470 nF is recommended. A capacitor between pin FSHB and SHHB is needed to supply the high-side driver. The recommended value for this capacitor is 1⁄5 of the value of the capacitor at VDD. A series resistor of at least 1 kΩ is recommended on pins AUXPFC and SLHB. UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 31 of 42 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx NXP Semiconductors UBA2016A_15_15A Objective data sheet 11.2 Without lamp current regulation or dimming mains Rev. 1 — 20 May 2011 FBPFC VDD GHHB AUXPFC SHHB FSHB UBA2016A GLHB COMPPFC SLHB GND IREF CF CPT CIFB DIM VFB BOOST IFB EOL 32 of 42 © NXP B.V. 2011. All rights reserved. Fig 16. Typical schematic for minimal TL or CFL application with UBA2016A (mains filter not shown) 600 V fluorescent lamp driver 001aam541 UBA2016A/15/15A All information provided in this document is subject to legal disclaimers. GPFC xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx NXP Semiconductors UBA2016A_15_15A Objective data sheet mains Rev. 1 — 20 May 2011 FBPFC VDD GHHB SHHB AUXPFC FSHB UBA2016A GLHB COMPPFC SLHB GND IREF CF CPT CIFB DIM VFB BOOST IFB EOL 33 of 42 © NXP B.V. 2011. All rights reserved. Fig 17. Typical schematic for basic TL or CFL application (better PFC performance than minimal application) (mains filter not shown) 600 V fluorescent lamp driver 001aan295 UBA2016A/15/15A All information provided in this document is subject to legal disclaimers. GPFC xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx NXP Semiconductors UBA2016A_15_15A Objective data sheet mains Rev. 1 — 20 May 2011 FBPFC VDD GHHB AUXPFC SHHB FSHB UBA2016A GLHB SLHB COMPPFC GND IREF CF CPT CIFB DIM VFB IFB BOOST EOL Fig 18. Typical schematic for basic TL or CFL application with UBA2016A with fixed time boost start (mains filter not shown) 600 V fluorescent lamp driver 34 of 42 © NXP B.V. 2011. All rights reserved. 001aam542 UBA2016A/15/15A All information provided in this document is subject to legal disclaimers. GPFC xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx NXP Semiconductors UBA2016A_15_15A Objective data sheet mains NTC mounted close to lamp Rev. 1 — 20 May 2011 FBPFC VDD VFB BOOST GHHB AUXPFC SHHB FSHB UBA2016A GLHB COMPPFC SLHB GND IREF CF CIFB DIM IFB EOL 35 of 42 © NXP B.V. 2011. All rights reserved. Fig 19. Typical schematic for basic TL or CFL application with UBA2016A, with lamp temperature-dependent boost start (mains filter not shown) 600 V fluorescent lamp driver 001aam543 UBA2016A/15/15A All information provided in this document is subject to legal disclaimers. GPFC xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx NXP Semiconductors UBA2016A_15_15A Objective data sheet 11.3 With lamp current regulation and dimming mains Rev. 1 — 20 May 2011 FBPFC VDD GHHB AUXPFC SHHB FSHB UBA2016A GLHB COMPPFC SLHB GND IREF CF CPT CIFB DIM BOOST VFB IFB EOL Fig 20. Typical schematic for dimmable TL application with UBA2016A (mains filter not shown) 600 V fluorescent lamp driver 36 of 42 © NXP B.V. 2011. All rights reserved. 001aam544 UBA2016A/15/15A All information provided in this document is subject to legal disclaimers. GPFC UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver 12. Package outline DIP20: plastic dual in-line package; 20 leads (300 mil) SOT146-1 ME seating plane D A2 A A1 L c e Z b1 w M (e 1) b MH 11 20 pin 1 index E 1 10 0 5 10 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 min. A2 max. b b1 c mm 4.2 0.51 3.2 1.73 1.30 0.53 0.38 0.36 0.23 26.92 26.54 inches 0.17 0.02 0.13 0.068 0.051 0.021 0.015 0.014 0.009 1.060 1.045 D e e1 L ME MH w Z (1) max. 6.40 6.22 2.54 7.62 3.60 3.05 8.25 7.80 10.0 8.3 0.254 2 0.25 0.24 0.1 0.3 0.14 0.12 0.32 0.31 0.39 0.33 0.01 0.078 (1) E (1) Note 1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. OUTLINE VERSION SOT146-1 REFERENCES IEC JEDEC JEITA MS-001 SC-603 EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-13 Fig 21. Package outline SOT146-1 (DIP20) UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 37 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver SO20: plastic small outline package; 20 leads; body width 7.5 mm SOT163-1 D E A X c HE y v M A Z 20 11 Q A2 A (A 3) A1 pin 1 index θ Lp L 10 1 e detail X w M bp 0 5 10 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (1) e HE L Lp Q v w y mm 2.65 0.3 0.1 2.45 2.25 0.25 0.49 0.36 0.32 0.23 13.0 12.6 7.6 7.4 1.27 10.65 10.00 1.4 1.1 0.4 1.1 1.0 0.25 0.25 0.1 0.01 0.019 0.013 0.014 0.009 0.51 0.49 0.30 0.29 0.05 0.419 0.043 0.055 0.394 0.016 inches 0.1 0.012 0.096 0.004 0.089 0.043 0.039 0.01 0.01 Z (1) 0.9 0.4 0.035 0.004 0.016 θ 8o o 0 Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT163-1 075E04 MS-013 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-19 Fig 22. Package outline SOT163-1 (SO20) UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 38 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver 13. Revision history Table 8. Revision history Document ID Release date Data sheet status Change notice Supersedes UBA2016A_15_15A v.1 20110520 Objective data sheet - - UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 39 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver 14. Legal information 14.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 14.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 14.3 Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities. UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 40 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond 14.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 15. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] UBA2016A_15_15A Objective data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 20 May 2011 © NXP B.V. 2011. All rights reserved. 41 of 42 UBA2016A/15/15A NXP Semiconductors 600 V fluorescent lamp driver 16. Contents 1 2 3 4 5 6 6.1 6.2 7 7.1 7.2 7.2.1 7.2.2 7.3 7.3.1 7.3.2 7.3.3 7.4 7.4.1 7.4.2 7.4.3 7.4.4 7.4.5 7.4.6 7.4.7 7.4.7.1 7.4.7.2 7.4.7.3 7.4.8 7.5 7.6 7.6.1 7.6.2 7.6.3 7.6.4 7.6.5 7.6.6 7.6.7 7.6.8 7.6.9 7.6.10 7.6.11 7.6.12 8 9 10 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 5 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5 Functional description . . . . . . . . . . . . . . . . . . . 6 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Power Factor Correction (PFC) . . . . . . . . . . . . 6 Regulation loop. . . . . . . . . . . . . . . . . . . . . . . . . 7 Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Half-bridge driver . . . . . . . . . . . . . . . . . . . . . . . 8 VDD supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Low- and high-side drivers . . . . . . . . . . . . . . . . 9 Non-overlap . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Fluorescent lamp control . . . . . . . . . . . . . . . . 10 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Standby. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Oscillating states (Preheat, Ignition and Burn) 12 Preheat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Auto-restart . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Burn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Lamp current control and dimming . . . . . . . . . 15 Operation without lamp current control. . . . . . 17 Boost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Stop state . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Enable and Disable . . . . . . . . . . . . . . . . . . . . 18 Protection circuits . . . . . . . . . . . . . . . . . . . . . . 18 End-of-life rectifying lamp detection . . . . . . . . 18 End-of-life overvoltage detection . . . . . . . . . . 19 Capacitive mode detection . . . . . . . . . . . . . . . 19 Hard switching regulation (UBA2016A) . . . . . 20 Hard switching protection . . . . . . . . . . . . . . . . 20 Coil saturation protection . . . . . . . . . . . . . . . . 22 Lamp overcurrent protection. . . . . . . . . . . . . . 22 Lamp overvoltage protection . . . . . . . . . . . . . 22 Lamp removal detection . . . . . . . . . . . . . . . . . 22 Temperature protection. . . . . . . . . . . . . . . . . . 22 Fault timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Brownout protection . . . . . . . . . . . . . . . . . . . . 23 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 24 Thermal characteristics . . . . . . . . . . . . . . . . . 25 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 25 11 11.1 11.2 11.3 12 13 14 14.1 14.2 14.3 14.4 15 16 Application information . . . . . . . . . . . . . . . . . Connecting the IC in an application . . . . . . . . Without lamp current regulation or dimming . With lamp current regulation and dimming . . Package outline. . . . . . . . . . . . . . . . . . . . . . . . Revision history . . . . . . . . . . . . . . . . . . . . . . . Legal information . . . . . . . . . . . . . . . . . . . . . . Data sheet status . . . . . . . . . . . . . . . . . . . . . . Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information . . . . . . . . . . . . . . . . . . . . Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 31 32 36 37 39 40 40 40 40 41 41 42 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2011. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 20 May 2011 Document identifier: UBA2016A_15_15A