UC1835 UC1836 UC2835 UC2836 UC3835 UC3836 High Efficiency Regulator Controller FEATURES DESCRIPTION • Complete Control for a High Current, Low Dropout, Linear Regulator • Fixed 5V or Adjustable Output Voltage • Accurate 2.5A Current Limiting with Foldback • Internal Current Sense Resistor The UC1835/6 families of linear controllers are optimized for the design of low cost, low dropout, linear regulators. Using an external pass element, dropout voltages of less than 0.5V are readily obtained. These devices contain a high gain error amplifier, a 250mA output driver, and a precision reference. In addition, current sense with foldback provides for a 2.5A peak output current dropping to less than 0.5A at short circuit. • Remote Sense for Improved Load Regulation • External Shutdown • Under-Voltage Lockout and Reverse Voltage Protection • Thermal Shutdown Protection • 8 Pin Mini-Dip Package (Surface Mount also Available) BLOCK DIAGRAM Note: Pin numbers refer to 8-Pin DIL Package 8/94 These devices are available in fixed, 5V, (UC1835), or adjustable, (UC1836), versions. In the fixed 5 volt version, the only external parts required are an external pass element, an output capacitor, and a compensation capacitor. On the adjustable version the output voltage can be set anywhere from 2.5V to 35V with two external resistors. Additional features of these devices include under-voltage lockout for predictable start-up, thermal shutdown and short circuit current limiting to protect the driver device. On the fixed voltage version, a reverse voltage comparator minimizes reverse load current in the event of a negative input to output differential. UC1835 UC1836 UC2835 UC2836 UC3835 UC3836 ABSOLUTE MAXIMUM RATINGS (Note 1) Input Supply Voltage (+VIN) . . . . . . . . . . . . . . . . –1.0V to + 40V Driver Output Current (Sink or Source) . . . . . . . . . . . . . 600mA Driver Source to Sink Voltage . . . . . . . . . . . . . . . . . . . . . + 40V Maximum Current Through Sense Resistor. . . . . . . . . . . . . . 4A VOUT Sense Input Voltage . . . . . . . . . . . . . . . . . . –.3V to + 40V Power Dissipation at TA = 25°C (Note 2) . . . . . . . . . . . 1000mW Power Dissipation at TC = 25°C (Note 2) . . . . . . . . . . . 2000mW Operating Junction Temperature . . . . . . . . . . . -55°C to +150°C Storage Temperature . . . . . . . . . . . . . . . . . . . . -65°C to +150°C Lead Temperature (Soldering, 10 Seconds) . . . . . . . . . . 300°C Note 1: Voltages are referenced to ground, (Pin 3). Currents are positive into, negative out of, the specified terminals. Consult Packaging Section of Databook for thermal considerations and limitations of packages. CONNECTION DIAGRAMS DIL-8, SOIC-8 (TOP VIEW) N or J Package, D Package PLCC-20, LCC-20 (TOP VIEW) Q, L Packages PACKAGE PIN FUNCTION FUNCTION PIN N/C +VIN +VIN N/C Compensation/ Shutdown N/C Ground N/C N/C Driver Source N/C VOUT Sense N/C N/C Driver Sink N/C Current Limit (-) N/C Sense Resistor Out Sense Resistor Out SOIC-16 (TOP VIEW) DW Package 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ELECTRICAL CHARACTERISTICS: Unless otherwise stated, specifications hold for TA = 0°C to + 70°C for the UC3835/6, –25°C to + 85°C for the UC2835/6, and –55°C to +125°C for the UC1835/6, +VIN = 6V, Driver Source= 0V, Driver Sink = 5V, TA = TJ. PARAMETER Input Supply Supply Current TEST CONDITIONS +VIN = 6V +VIN = 40V +VIN Low to High, VOUT Sense = 0V UVLO Threshold Threshold Hysteresis Reverse Current +VIN = -1.0V, Driver Sink Open Regulating Voltage and Error Amplifier (UC1835 Family Only) Driver Current = 10mA, TJ = 25°C Regulating Level at VOUT Sense (VREG) Over Temperature Line Regulation +VIN = 5.2V + 35V Load Regulation Driver Current = 0 to 250mA VOUT Sense = 5.0V Bias Current at VOUT Sense Error Amp Transconductance ±100µA at Compensation/Shutdown Pin Maximum Compensation Output Current Sink or Source, Driver Source Open 2 MIN. TYP. MAX. UNITS 3.9 2.75 3.75 4.4 0.1 6.0 4.0 6.0 4.9 0.35 20 mA mA V V mA 5.0 5.06 5.1 40 25 210 2.0 260 V V mV mV µA mS µA 4.94 4.9 75 0.8 90 15 6.0 125 1.3 200 UC1835 UC1836 UC2835 UC2836 UC3835 UC3836 ELECTRICAL CHARACTERISTICS: Unless otherwise stated, specifications hold for TA = 0°C to + 70°C for the UC3835/6, –25°C to + 85°C for the UC2835/6, and –55°C to +125°C for the UC1835/6, +VIN = 6V, Driver Source= 0V, Driver Sink = 5V, TA = TJ. PARAMETER TEST CONDITIONS MIN. TYP. Regulating Voltage and Error Amplifier (UC1836 Family Only) Driver Current = 10mA, TJ = 25°C 2.47 2.5 Regulating Level at VOUT Sense (VREG) Over Temperature 2.45 6.0 Line Regulation +VIN = 5.2V to 35V Load Regulation Driver Current = 0 to 250mA 3.0 VOUT Sense =2.5V -1.0 -0.2 Bias Current at VOUT Sense Error Amp Transconductance ±100µA at Compensation/Shutdown Pin 0.8 1.3 Maximum Compensation Output Current Sink or Source, Driver Source Open 90 200 Driver Maximum Current 250 500 Saturation Voltage Driver Current = 250mA, Driver Sink 2.0 Pull-Up Current at Driver Sink Compensation/Shutdown=0.45V 140 250 Driver Sink Leakage In UVLO In Reverse Voltage (UC1835 Family Only) Thermal Shutdown 165 Foldback Current Limit 2.2 2.5 Current Limit Levels at Sense Resistor Out VOUT Sense = (0.99) VREG VOUT Sense = (0.5) VREG 1.3 1.5 0.25 0.4 VOUT Sense = 0V 12 24 Current Limit Amp Tansconductance ±100µA at Compensation/Shutdown, VOUT Sense = (0.9) VREG Limiting Voltage at Current Limit (-) VOUT Sense = (0.9) VREG 80 100 (Note 2) Volts Below +VIN, TJ = 25°C Sense Resistor Value (Note 3) VOUT Sense = (0.9) VREG, 40 IOUT = IA, TJ = 25°C Note 2: This voltage has a positive temperature coefficient of approximately 3500ppm/°C. Note 3: This resistance has a positive temperature coefficient of approximately 3500ppm/°C. The total resistance from Pin 1 to Pin 8 will include an additional 60 to 100mΩ of package resistance. MAX. UNITS 2.53 2.55 20 15 2.0 260 2.8 300 10 10 mA V µA µA µA °C 2.8 1.7 0.55 42 A A A mS 140 mV APPLICATION AND OPERATION INFORMATION UC 1835 − Typical configurations for a 2A, Low Dropout 5V Regulator UC1836 − Typical Configuration for a 2A, Low Dropout Adjustable Regulator Note 4: Suggested Pass devices are TIP 32B. (Dropout Voltage ≤0.75V) or, D45H, (Dropout Voltage ≤0.5V), or equivalents. 3 V V mV mV µA mS µA mΩ UC1835 UC1836 UC2835 UC2836 UC3835 UC3836 APPLICATION AND OPERATION INFORMATION (cont.) UC1835/6 Foldback Current Limiting UC3835/36 TYPICAL APPLICATIONS Low Current Application Typical Output Current vs VIN and VOUT using the UC3836 internal drive transistor of the UC3836 internal drive transistor for PDISS = 0.5W (approx.) High Current Application Parallel Pass Transistors using drive transistor Q2 to increase Q1 base drive and reduce UC3836 power dissipation can be added for high current or high power dissipation applications EQUATIONS: R1 = 0.100 V/IOUT (MAX) R2 = (VOUT - 2.5V/1mA) R3 = ((VIN - VBE - VSAT)*BETA(min))/IOUT (max) UNITRODE INTEGRATED CIRCUITS 7 CONTINENTAL BLVD. • MERRIMACK, NH 03054 TEL. (603) 424-2410 • FAX 603-424-3460 4 PACKAGE OPTION ADDENDUM www.ti.com 5-Sep-2011 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty 1 5962-9065002PA ACTIVE CDIP JG 8 UC1835J OBSOLETE CDIP JG Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) (Requires Login) TBD Call TI Call TI 8 TBD Call TI Call TI UC1835J883B OBSOLETE CDIP JG 8 TBD Call TI Call TI UC1835L883B OBSOLETE LCCC FK 20 TBD Call TI Call TI UC1836J ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type 1 TBD A42 N / A for Pkg Type TBD Call TI Call TI Call TI Call TI UC1836J883B ACTIVE CDIP JG 8 UC1836L OBSOLETE TO/SOT L 20 UC1836L883B OBSOLETE TO/SOT L 20 UC2835D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC2835DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TBD TBD UC2835J OBSOLETE CDIP JG 8 UC2835N ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC2835NG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC2836D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC2836DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC2836DW OBSOLETE SOIC DW 16 UC3835N ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC3835NG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC3836D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3836DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3836DTR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TBD Addendum-Page 1 Call TI Call TI Samples Call TI Call TI PACKAGE OPTION ADDENDUM www.ti.com 5-Sep-2011 Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) UC3836DTRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3836N ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC3836NG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF UC1835, UC1836, UC3835, UC3836 : • Catalog: UC3835, UC3836 • Military: UC1835, UC1836 Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 5-Sep-2011 NOTE: Qualified Version Definitions: • Catalog - TI's standard catalog product • Military - QML certified for Military and Defense Applications Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device UC3836DTR Package Package Pins Type Drawing SOIC D 8 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2500 330.0 12.4 Pack Materials-Page 1 6.4 B0 (mm) K0 (mm) P1 (mm) 5.2 2.1 8.0 W Pin1 (mm) Quadrant 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) UC3836DTR SOIC D 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated