UC1902 UC2902 UC3902 Load Share Controller PRELIMINARY FEATURES DESCRIPTION • 2.7V to 20V Operation The UC3902 load share controller is an 8-pin device that balances the current drawn from independent, paralleled power supplies. Load sharing is accomplished by adjusting each supply’s output current to a level proportional to the voltage on a share bus. • 8-Pin Package • Requires Minimum Number of External Components The master power supply, which is automatically designated as the supply that regulates to the highest voltage, drives the share bus with a voltage proportional to its output current. The UC3902 trims the output voltage of the other paralleled supplies so that they each support their share of the load current. Typically, each supply is designed for the same current level Differential Share Bus although that is not necessary for use with the UC3902. By appropriately Precision Current Sense Amplifier with scaling the current sense resistor, supplies with different output current caGain of 40 pability can be paralleled with each supply providing the same percentage of their output current capability for a particular load. UVLO (Undervoltage Lockout) Circuitry A differential line is used for the share bus to maximize noise immunity and accommodate different voltage drops in each power converter’s ground reUser Programmable Share Loop turn line. Trimming of each converter’s output voltage is accomplished by Compensation injecting a small current into the output voltage sense line, which requires a small resistance (typically 20Ω – 100Ω) to be inserted. • Compatible with Existing Power Supply Designs Incorporating Remote Output Voltage Sensing • • • • BLOCK DIAGRAM LOAD SHARE CONTROLLER GND 1 BIAS 8 VCC 7 SHARE+ 6 SHARE– 5 COMP UVLO SHARE DRIVE AMPLIFIER 40R – + R SENSE – + 2 + SHARE SENSE AMPLIFIER – CURRENT SENSE AMPLIFIER ADJ 3 ADJ AMPLIFIER 0.6V + – ADJR 35mV + + + – ERROR AMPLIFIER 2.3V 4 UDG-99042 SLUS232 - FEBRUARY 1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 UC1902 UC2902 UC3902 ABSOLUTE MAXIMUM RATINGS CONNECTION DIAGRAM Supply Voltage (ADJ and VCC) . . . . . . . . . . . . . . –0.3V to 20V SENSE Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . –5V to +5V ADJR, COMP Voltage. . . . . . . . . . . . . . . . . . . . . . –0.3V to +4V SHARE–, SHARE+ Voltages . . . . . . . . . . . . . . . . –0.3V to 10V SHARE+ Current . . . . . . . . . . . . . . . . . . . . . –100mA to +10mA ADJ Current . . . . . . . . . . . . . . . . . . . . . . . . . . . –1mA to +30mA Storage Temperature . . . . . . . . . . . . . . . . . . . –65°C to +150°C Junction Temperature . . . . . . . . . . . . . . . . . . . –55°C to +150°C Lead Temperature (Soldering, 10sec.) . . . . . . . . . . . . . +300°C DIL-8, SOIC-8 (Top View) N, J and D Package All voltages are with respect to pin 1. Currents are positive into, negative out of the specified terminal. Consult Packaging Section of the Databook for thermal limitations and considerations of packages. ELECTRICAL CHARACTERISTICS: Unless otherwise specified, TA = –55°C to +125°C for UC1902, –40°C to+85°C for UC2902, 0°C to 70°C for UC3902, VCC = 5V, RADJR = 1kΩ, VADJ = 5V, COMP = 5nF capacitor to GND, VSHARE– = 0V, TA = TJ. PARAMETERS TEST CONDITIONS MIN TYP MAX UNIT SHARE+ = 1V, SENSE = 0V 4 6 mA VCC = 20V 6 10 mA Power Supply Supply Current Undervoltage Lockout Startup Voltage SHARE+ = 0.2V, SENSE = 0V, COMP = 1V 2.3 2.5 2.7 V Hysteresis SHARE+ = 0.2V, SENSE = 0V, COMP = 1V 60 100 140 mV Current Sense Amplifier Input Offset Voltage 0.1V ≤ SHARE+ ≤ 1.1V –2.5 –0.5 1.5 mV Gain SENSE to SHARE 0.1V ≤ SHARE+ ≤ 1.1V –41 –40 -39 V/V 0.6 1 1.5 kΩ VCC = 2.5V, SENSE = –50mV, ISHARE+ = –1mA 1.2 1.4 VCC = 12V, SENSE = –250mV, ISHARE+ = –1mA 9.6 10 10.4 V VCC = 20V, SENSE = –250mV, ISHARE+ = –1mA 9.6 10 10.4 V VCC = 2.5V, SENSE = +10mV, ISHARE+ = –1mA 20 50 mV VCC = 12V, SENSE = +10mV, ISHARE+ = –1mA 20 50 mV Input Resistance Share Drive Amplifier SHARE+ High SHARE+ Low V VCC = 20V, SENSE = +10mV, ISHARE+ = –1mA 20 50 mV SHARE+ Output Voltage Measures SHARE+, SENSE = 0mV, RSHARE+ = 200Ω resistor SHARE+ to GND 20 40 mV CMRR 0 ≤ SHARE– ≤ 1V , SENSE used as input to amplifier Load Regulation Load on SHARE+, –1mA ≤ ILOAD ≤ –20mA, SENSE = –25mV 50 90 0 dB 20 mV Short Circuit Current SHARE+ = 0V, SENSE = –25mV –85 –50 –20 mA Slew Rate SENSE = +10mV to –90mV Step, 200Ω resistor SHARE+ to GND 0.16 0.27 0.37 V/µs SENSE = –90mV to +10mV Step, 200Ω resistor SHARE+ to GND 0.12 0.24 0.34 V/µs Powered by ICminer.com Electronic-Library Service CopyRight 2003 2 UC1902 UC2902 UC3902 ELECTRICAL CHARACTERISTICS: Unless otherwise specified, TA = –55°C to +125°C for UC1902, –40°C to+85°C for UC2902, 0°C to 70°C for UC3902, VCC = 5V, RADJR = 1kΩ, VADJ = 5V, COMP = 5nF capacitor to GND, VSHARE– = 0V, TA = TJ. PARAMETERS TEST CONDITIONS MIN TYP MAX UNIT SHARE+ = 1V, SHARE– = 1V, SENSE = +10mV 10 15 kΩ 200Ω resistor SHARE+ to GND, SHARE– = 1V, SENSE = +10mV 15 17 kΩ Share Sense Amplifier Input Impedance Threshold SENSE = 0V 41 70 CMRR SHARE 0 ≤ SHARE– ≤ 1V, SENSE = –2.5mV 50 60 dB AVOL from SHARE+ to ADJR SENSE = –2.5mV, 5nF capacitor COMP to GND, 1k resistor ADJR to GND 50 68 dB SENSE = –2.5mV, 5nF capacitor COMP to GND, 150Ω resistor ADJR to GND 50 66 dB SHARE+ = Step of 0mV to 300mV through a 200Ω resistor, RCOMP = 500Ω resistor to 1.5V, SENSE = 10mV 0.4 0.7 1 V/µs Transconductance, SHARE+ to COMP 200Ω resistor SHARE+ to GND 3.2 4.5 5.5 mS IOH COMP = 1.5V, SHARE+ ≥ +300mV, SENSE = +10mV –400 –325 –230 µA IOL 200Ω resistor SHARE+ to GND, COMP = 1.5V, SENSE = +10mV 100 150 200 µA Slew Rate 100 mV Error Amplifier Section Input Offset Voltage 15 35 65 mV 1k Resistor, ADJR to GND, –2.5mV < SENSE < –25mV –6 0 6 mV/V ADJR Low Voltage SENSE = +10mV, 200Ω resistor SHARE+ to GND –1 0 1 mV ADJR High Voltage SENSE = +10mV, SHARE+ = 1V 1.4 1.8 2.1 V Current Gain ADJR to ADJ ADJR Current = –0.5mA, ADJ = 2.5V, SENSE = +10mV, SHARE+ = 1V 0.96 0.99 1 A/A ADJR Current = –0.5mA, ADJ = 20V, SENSE = +10mV, SHARE+ = 1V 0.96 0.99 1 A/A ADJR Current = –10mA, ADJ = 2.5V, SENSE = +10mV, SHARE+ = 1V 0.96 0.99 1 A/A ADJR Current = –10mA, ADJ = 20V, SENSE = +10mV, SHARE+ = 1V 0.96 0.99 1 A/A ∆ VIO/∆ VSENSE ADJ Amplifier PIN DESCRIPTIONS GND: Local power supply return and signal ground. ADJ: Current output of adjust amplifier circuit (NPN collector). SENSE: Inverting input of current sense amplifier. ADJR: Current adjust amplifier range set (NPN emitter). SHARE+: Positive input from share bus or drive to share bus. COMP: Output of error amplifier, input of adjust amplifier. This is where the compensation capacitor is connected. SHARE-: Reference for SHARE+. VCC: Local power supply (positive). Powered by ICminer.com Electronic-Library Service CopyRight 2003 3 UC1902 UC2902 UC3902 APPLICATION INFORMATION UDG-96200 Figure 1. Typical application. Powered by ICminer.com Electronic-Library Service CopyRight 2003 4 UC1902 UC2902 UC3902 APPLICATION INFORMATION (cont.) RADJ must be low enough to not affect the normal operation of the converter’s voltage feedback loop. Typical RADJ values are in the 20Ω to100Ω range depending on VO, ∆VO(max) and the selected IADJ(max) value. The values of five passive components must be determined to configure the UC3902 load share controller. The output and return lines of each converter are connected together at the load, with current sense resistor RSENSE inserted in each negative return line. Another resistor, RADJ, is also inserted in each positive remote sense line. The differential share bus terminals (SHARE+ and SHARE–) of each UC3902 are connected together respectively, and the SHARE– node is also connected to the system ground. A typical application is illustrated in Figure 1. Step 4. CC = The share loop compensation capacitor, CC is calculated to produce the desired share loop unity gain crossover frequency, fC. The share loop error amplifier’s transconductance, GM is nominally 4.5ms. The values of the resistors are already known. Typically, fC will be set at least an order of magnitude below the converter’s closed loop bandwidth. The load share circuit is primarily intended to compensate for each converter’s initial output voltage tolerance and temperature drift, not differences in their transient response. The term APWR(fC) is the gain of the power supply measured at the desired share loop crossover frequency, fC. This gain can be measured by injecting the measurement signal between the positive output and the positive sense terminal of the power supply. The load share controller design can be executed by following the next few steps: Step 1. R SENSE = V SHARE (max) ACSA • IO (max) where ACSA is 40, the gain of the current sense amplifier. At full load, the voltage drop across the RSENSE resistor is IO (max) • RSENSE. Taking into account the gain of the current sense amplifier, the voltage at full load on the current share bus, V SHARE (max) = ACSA • IO (max) • R SENSE . Step 5. This voltage must stay 1.5V below VCC or below 10V whichever is smaller. VSHARE represents an upper limit but the designer should select the full scale share bus voltage keeping in mind that every volt on the load share bus will increase the master controller’s supply current by approximately 100mA times the number of slave units connected parallel. RC = When the system is powered up, the converter with the highest output voltage will tend to source the most current and take control of the share bus. The other converters will increase their output voltages until their output currents are proportional to the share bus voltage minus 50mV. The converter which in functioning as the master may change due to warmup drift and differences in load and line transient response of each converter. V ADJ (max) I ADJ (max) Care must be taken to ensure that IADJ(max) is low enough to ensure that both the drive current and power dissipation are within the UC3902’s capability. For most applications, an IADJ(max) current between 5mA and 10mA is acceptable. In a typical application, a 360Ω RG resistor from the ADJR pin to ground sets IADJ(max) to approximately 5mA. ADDITIONAL INFORMATION Please refer to the following Unitrode topic for additional application information. [1] Application Note U-163, The UC3902 Load Share Controller and Its Performance in Distributed Power Systems by Laszlo Balogh. Step 3. RADJ = ∆ VO (max) – IO (max) • R SENSE I ADJ (max) UNITRODE CORPORATION 7 CONTINENTAL BLVD. • MERRIMACK, NH 03054 TEL. (603) 424-2410 FAX (603) 424-3460 Powered by ICminer.com Electronic-Library Service CopyRight 2003 1 2 • π • fC • CC A resistor in series with CC is required to boost the phase margin of the load share loop. The zero is placed at the load share loop crossover frequency, fC. Step 2. RG = GM R R • ADJ • SENSE • ACSA • APWR (fC ) 2 • π • fC RG R LOAD 5 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1999, Texas Instruments Incorporated Powered by ICminer.com Electronic-Library Service CopyRight 2003