application INFO available UC1842/3/4/5 UC2842/3/4/5 UC3842/3/4/5 Current Mode PWM Controller FEATURES DESCRIPTION • Optimized For Off-line And DC To DC Converters • Low Start Up Current (<1mA) • Automatic Feed Forward Compensation • Pulse-by-pulse Current Limiting • The UC1842/3/4/5 family of control ICs provides the necessary features to implement off-line or DC to DC fixed frequency current mode control schemes with a minimal external parts count. Internally implemented circuits include under-voltage lockout featuring start up current less than 1mA, a precision reference trimmed for accuracy at the error amp input, logic to insure latched operation, a PWM comparator which also provides current limit control, and a totem pole output stage designed to source or sink high peak current. The output stage, suitable for driving N Channel MOSFETs, is low in the off state. Enhanced Load Response Characteristics • Under-voltage Lockout With Hysteresis • Double Pulse Suppression • High Current Totem Pole Output • Internally Trimmed Bandgap Reference • 500khz Operation • Low RO Error Amp Differences between members of this family are the under-voltage lockout thresholds and maximum duty cycle ranges. The UC1842 and UC1844 have UVLO thresholds of 16V (on) and 10V (off), ideally suited to off-line applications. The corresponding thresholds for the UC1843 and UC1845 are 8.4V and 7.6V. The UC1842 and UC1843 can operate to duty cycles approaching 100%. A range of zero to 50% is obtained by the UC1844 and UC1845 by the addition of an internal toggle flip flop which blanks the output off every other clock cycle. BLOCK DIAGRAM Note 1: A/B Note 2: A = DIL-8 Pin Number. B = SO-14 and CFP-14 Pin Number. Toggle flip flop used only in 1844 and 1845. SLUS223A - APRIL 1997 - REVISED MAY 2002 UC1842/3/4/5 UC2842/3/4/5 UC3842/3/4/5 ABSOLUTE MAXIMUM RATINGS (Note 1) Supply Voltage (Low Impedance Source) . . . . . . . . . . . . . . 30V Supply Voltage (ICC < 30mA) . . . . . . . . . . . . . . . . . Self Limiting Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±1A Output Energy (Capacitive Load). . . . . . . . . . . . . . . . . . . . . 5µJ Analog Inputs (Pins 2, 3). . . . . . . . . . . . . . . . . . . -0.3V to +6.3V Error Amp Output Sink Current . . . . . . . . . . . . . . . . . . . . 10mA Power Dissipation at TA ≤ 25°Χ (DIL−8) . . . . . . . . . . . . . . . . . . 1Ω Power Dissipation at TA ≤ 25°C (SOIC-14) . . . . . . . . . . 725mW Storage Temperature Range . . . . . . . . . . . . . . -65°C to +150°C Lead Temperature (Soldering, 10 Seconds) . . . . . . . . . . 300°C Note 1: All voltages are with respect to Pin 5. All currents are positive into the specified terminal. Consult Packaging Section of Databook for thermal limitations and considerations of packages. CONNECTION DIAGRAMS DIL-8, SOIC-8 (TOP VIEW) N or J Package, D8 Package PLCC-20 (TOP VIEW) Q Package PACKAGE PIN FUNCTION FUNCTION PIN 1 N/C COMP 2 N/C N/C VFB N/C ISENSE N/C N/C RT/CT N/C PWR GND GROUND N/C OUTPUT N/C VC VCC N/C VREF SOIC-14, CFP-14. (TOP VIEW) D or W Package 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 DISSIPATION RATING TABLE Package W TA ≤ 25°C Power Rating 700 mW TA ≤ 70°C Power Rating 452 mW Derating Factor Above TA ≤ 25°C 5.5 mW/°C 2 TA ≤ 85°C Power Rating 370 mW TA ≤ 125°C Power Rating 150 mW UC1842/3/4/5 UC2842/3/4/5 UC3842/3/4/5 ELECTRICAL CHARACTERISTICS: PARAMETER Unless otherwise stated, these specifications apply for -55°C ≤ TA ≤ 125°C for the UC184X; -40°C ≤ TA ≤ 85°C for the UC284X; 0°C ≤ TA ≤ 70°C for the 384X; VCC = 15V (Note 5); RT = 10k; CT = 3.3nF, TA=TJ. UC1842/3/4/5 UC2842/3/4/5 TEST CONDITIONS UC3842/3/4/5 UNITS MIN TYP MAX MIN TYP MAX 4.95 5.00 5.05 4.90 5.00 5.10 V 6 20 6 20 mV Reference Section Output Voltage TJ = 25°C, IO = 1mA Line Regulation 12 ≤ VIN ≤ 25V Load Regulation 1 ≤ I0 ≤ 20mA Temp. Stability (Note 2) (Note 7) Total Output Variation Line, Load, Temp. (Note 2) Output Noise Voltage 10Hz ≤ f ≤ 10kHz, TJ = 25°C (Note2) Long Term Stability TA = 125°C, 1000Hrs. (Note 2) 6 25 6 25 mV 0.2 0.4 0.2 0.4 mV/°C 4.9 Output Short Circuit 5.1 4.82 50 5.18 V µV 50 5 25 5 25 mV -30 -100 -180 -30 -100 -180 mA 47 52 57 47 52 57 kHz 0.2 1 0.2 1 % Oscillator Section Initial Accuracy TJ = 25°C (Note 6) Voltage Stability 12 ≤ VCC ≤ 25V Temp. Stability TMIN ≤ TA ≤ TMAX (Note 2) Amplitude VPIN 4 peak to peak (Note 2) 5 5 % 1.7 1.7 V Error Amp Section VPIN 1 = 2.5V Input Voltage 2.45 Input Bias Current 2.50 2.55 -0.3 -1 2.42 2.50 2.58 V -0.3 -2 µA AVOL 2 ≤ VO ≤ 4V 65 90 65 90 dB Unity Gain Bandwidth (Note 2) TJ = 25°C 0.7 1 0.7 1 MHz PSRR 12 ≤ VCC ≤ 25V 60 70 60 70 dB Output Sink Current VPIN 2 = 2.7V, VPIN 1 = 1.1V 2 6 2 6 mA -0.5 -0.8 -0.5 -0.8 mA 5 6 5 6 V Output Source Current VPIN 2 = 2.3V, VPIN 1 = 5V VOUT High VPIN 2 = 2.3V, RL = 15k to ground VOUT Low VPIN 2 = 2.7V, RL = 15k to Pin 8 0.7 1.1 0.7 1.1 V Current Sense Section Gain (Notes 3 and 4) 2.85 3 3.15 2.85 3 3.15 V/V Maximum Input Signal VPIN 1 = 5V (Note 3) 0.9 1 1.1 0.9 1 1.1 V PSRR 12 ≤ VCC ≤ 25V (Note 3) (Note 2) Input Bias Current Delay to Output Note 2: Note 3: Note 4: Note 5: Note 6: Note 7: VPIN 3 = 0 to 2V (Note 2) 70 70 dB -2 -10 -2 -10 µA 150 300 150 300 ns These parameters, although guaranteed, are not 100% tested in production. Parameter measured at trip point of latch with VPIN 2 = 0. Gain defined as ∆ VPIN 1 A= , 0 ≤ VPIN 3 ≤ 0.8V ∆ VPIN 3 Adjust VCC above the start threshold before setting at 15V. Output frequency equals oscillator frequency for the UC1842 and UC1843. Output frequency is one half oscillator frequency for the UC1844 and UC1845. Temperature stability, sometimes referred to as average temperature coefficient, is described by the equation: V (max ) − VREF (min ) Temp Stability = REF TJ (max ) − TJ (min ) VREF (max) and VREF (min) are the maximum and minimum reference voltages measured over the appropriate temperature range. Note that the extremes in voltage do not necessarily occur at the extremes in temperature. 3 UC1842/3/4/5 UC2842/3/4/5 UC3842/3/4/5 ELECTRICAL CHARACTERISTICS: PARAMETER Unless otherwise stated, these specifications apply for −55°C ≤ TA ≤ 125°C for the UC184X; −40°C ≤ TA ≤ 85°C for the UC284X; 0°C ≤ TA ≤ 70°C for the 384X; VCC = 15V (Note 5); RT = 10k; CT = 3.3nF, TA=TJ. UC1842/3/4/5 UC2842/3/4/5 TEST CONDITION MIN UC3842/3/4/5 TYP MAX ISINK = 20mA 0.1 ISINK = 200mA 1.5 MIN UNITS TYP MAX 0.4 0.1 0.4 V 2.2 1.5 2.2 V Output Section Output Low Level Output High Level ISOURCE = 20mA 13 13.5 13 13.5 V ISOURCE = 200mA 12 13.5 12 13.5 V Rise Time TJ = 25°C, CL = 1nF (Note 2) 50 150 50 150 ns Fall Time TJ = 25°C, CL = 1nF (Note 2) 50 150 50 150 ns 14.5 16 17.5 V Under-voltage Lockout Section Start Threshold Min. Operating Voltage After Turn On X842/4 15 16 17 X843/5 7.8 8.4 9.0 7.8 8.4 9.0 V X842/4 9 10 11 8.5 10 11.5 V X843/5 7.0 7.6 8.2 7.0 7.6 8.2 V PWM Section Maximum Duty Cycle X842/3 95 97 100 95 97 100 % X844/5 46 48 50 47 48 50 % 0 % Minimum Duty Cycle 0 Total Standby Current Start-Up Current Operating Supply Current VPIN 2 = VPIN 3 = 0V 0.5 1 0.5 1 mA 11 17 11 17 mA ICC = 25mA 30 34 VCC Zener Voltage Note 2: These parameters, although guaranteed, are not 100% tested in production. Note 3: Parameter measured at trip point of latch with VPIN 2 = 0 . ∆ VPIN 1 Note 4: Gain defined as: A = ; 0 ≤ VPIN 3 ≤ 0.8V . ∆ VPIN 3 Note 5: Adjust VCC above the start threshold before setting at 15V. Note 6: Output frequency equals oscillator frequency for the UC1842 and UC1843. Output frequency is one half oscillator frequency for the UC1844 and UC1845. ERROR AMP CONFIGURATION Error Amp can Source or Sink up to 0.5mA 4 30 34 V UC1842/3/4/5 UC2842/3/4/5 UC3842/3/4/5 UNDER-VOLTAGE LOCKOUT During under-voltage lock-out, the output driver is biased to sink minor amounts of current. Pin 6 should be shunted to ground with a bleeder resistor to prevent activating the power switch with extraneous leakage currents. CURRENT SENSE CIRCUIT Peak Current (IS) is Determined By The Formula ISMAX ′ RS A small RC filter may be required to suppress switch transients. OSCILLATOR SECTION 5 UC1842/3/4/5 UC2842/3/4/5 ERROR AMPLIFIER OPEN-LOOP FREQUENCY RESPONSE OUTPUT SATURATION CHARACTERISTICS OPEN-LOOP LABORATORY FIXTURE High peak currents associated with capacitive loads necessitate careful grounding techniques. Timing and bypass capacitors should be connected close to pin 5 in a single point ground. The transistor and 5k potentiometer are used to sample the oscillator waveform and apply an adjustable ramp to pin 3. SHUT DOWN TECHNIQUES Shutdown of the UC1842 can be accomplished by two methods; either raise pin 3 above 1V or pull pin 1 below a voltage two diode drops above ground. Either method causes the output of the PWM comparator to be high (refer to block diagram). The PWM latch is reset dominant so that the output will remain low until the next clock cycle after the shutdown condition at pin 1 and/or 3 is removed. In one example, an externally latched shutdown may be accomplished by adding an SCR which will be reset by cycling VCC below the lower UVLO threshold. At this point the reference turns off, allowing the SCR to reset. 6 UC1842/3/4/5 UC2842/3/4/5 UC3842/3/4/5 OFFLINE FLYBACK REGULATOR 5. Output Voltage: A. +5V, ±5%; 1A to 4A load Ripple voltage: 50mV P-P Max Power Supply Specifications 1. Input Voltages 5VAC to 130VA (50 Hz/60Hz) 2. Line Isolation 3750V 3. Switching Frequency 40kHz B. +12V, ±3%; 0.1A to 0.3A load Ripple voltage: 100mV P-P Max C. -12V ,±3%; 0.1A to 0.3A load Ripple voltage: 100mV P-P Max 4. Efficiency at Full Load 70% SLOPE COMPENSATION A fraction of the oscillator ramp can be resistively summed with the current sense signal to provide slope compensation for converters requiring duty cycles over 50%. 7 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third–party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2002, Texas Instruments Incorporated