TI UCC2895DW

SLUS157L − DECEMBER 1999 − REVISED APRIL 2008
FEATURES
D Programmable Output Turn-on Delay
D Adaptive Delay Set
D Bidirectional Oscillator Synchronization
D Voltage-Mode, Peak Current-Mode, or
DESCRIPTION
The UCC3895 is a phase-shift PWM controller
that implements control of a full-bridge power
stage by phase shifting the switching of one
half-bridge with respect to the other. It allows
constant frequency pulse-width modulation in
conjunction with resonant zero-voltage switching
to provide high efficiency at high frequencies. The
part can be used either as a voltage-mode or
current-mode controller.
Average Current-Mode Control
D Programmable Softstart/Softstop and Chip
D
D
D
D
D
Disable via a Single Pin
0% to 100% Duty-Cycle Control
7-MHz Error Amplifier
Operation to 1 MHz
Typical 5-mA Operating Current at 500 kHz
Very Low 150-µA Current During UVLO
While the UCC3895 maintains the functionality of
the UC3875/6/7/8 family and UC3879, it improves
on that controller family with additional features
such as enhanced control logic, adaptive delay
set, and shutdown capability. Since it is built using
the BCDMOS process, it operates with
dramatically less supply current than it’s bipolar
counterparts. The UCC3895 can operate with a
maximum clock frequency of 1 MHz.
APPLICATIONS
D Phase-Shifted Full-Bridge Converters
D Off-Line, Telecom, Datacom and Servers
D Distributed Power Architecture
D High-Density Power Modules
UCC3895
1
EAN
2
EAOUT
3
Q1
EAP
20
7
SS/DISB
19
RAMP
OUTA
18
4
REF
OUTB
17
5
GND
PGND
16
6
SYNC
VCC
15
7
CT
OUTC
14
8
RT
OUTD
13
9
DELAB
CS
12
10
DELCD
ADS
11
VOUT
A
C
VIN
VBIAS
B
D
UDG−03123
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
!"#
$ %&'# "$ (&)*
%"#
+"#',
+&%#$ %! # $('%
%"#
$ (' #-' #'!$ '."$ $#&!'#$
$#"+"+ /""#0, +&%#
(%'$$
1 +'$ # '%'$$"
*0 %*&+'
#'$#
1 "** (""!'#'$,
Copyright  2008, Texas Instruments Incorporated
www.ti.com
1
SLUS157L − DECEMBER 1999 − REVISED APRIL 2008
ORDERING INFORMATION
PACKAGED DEVICES
TA
SOIC−20(DW)(1)
PDIP−20(N)
TSSOP−20(PW)
(1)
PLCC−20(Q)(1)
−55°C to 125°C
−40°C to 85°C
UCC2895DW
UCC2895N
UCC2895PW
0°C to 70°C
UCC3895DW
UCC3895N
UCC3895PW
CLCC−20(L)
CDIP−20(J)
UCC1895L
UCC1895J
UCC2895Q
UCC3895Q
(1) The DW, PW and Q packages are available taped and reeled. Add TR suffix to device
type (e.g. UCC2895DWTR) to order quantities of 2000 devices per reel for DW.
N and J PACKAGE
(TOP VIEW)
PW and DW PACKAGE
(TOP VIEW)
EAN
EAOUT
RAMP
REF
GND
SYNC
CT
RT
DELAB
DELCD
1
2
3
4
5
6
7
8
9
10
EAN
EAOUT
RAMP
REF
GND
SYNC
CT
RT
DELAB
DELCD
EAP
SS/DISB
OUTA
OUTB
PGND
VDD
OUTC
OUTD
CS
ADS
20
19
18
17
16
15
14
13
12
11
1
20
2
19
3
18
4
17
5
16
6
15
7
14
8
13
9
12
10
11
Q and L PACKAGE
(TOP VIEW)
EAN
EAOUT
RAMP
EAP
SS/DISB
3
2
1 20 19
REF
4
18
OUTA
GND
5
17
OUTB
SYNC
6
16
PGND
CT
7
15
VDD
RT
8
14
OUTC
9 10 11 12 13
DELAB
DELCD
2
OUTD
CS
ADS
www.ti.com
EAP
SS/DISB
OUTA
OUTB
PGND
VDD
OUTC
OUTD
CS
ADS
SLUS157L − DECEMBER 1999 − REVISED APRIL 2008
ABSOLUTE MAXIMUM RATINGS
−40°C ≤ TA ≤ 85°C, all voltage values are with respect to the network ground terminal unless otherwise noted. (2)
Supply voltage
UCC2895N
UNIT
17
V
(IDD < 10 mA)
Supply current
30
Reference current
15
Output crrent
100
Analog inputs
EAP, EAN, EAOUT, RAMP, SYNC, ADS, CS, SS/DISB
Drive outputs
OUTA, OUTB, OUTC, OUTD
−0.3 V to REF+0.3 V
−0.3 V to VCC + 0.3 V
DW−20 package
Power dissipation at TA = 25°C
mA
V
650
mW
1
W
N−20 package
Storage temperature range, Tstg
−65 to 150
Junction temperature range, TJ
−55 to 150
°C
C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds
300
(2) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only,
and functional operation of the device at these or any other conditions beyond those indicated under ”recommended operating conditions” is
not implied. Exposure to Absolute Maximum Rated conditions for extended periods may affect device reliability
RECOMMENDED OPERATING CONDITIONS(3)
MIN
Supply voltage, VDD
TYP
9
Supply voltage bypass capacitor, VDD(1)
Reference bypass capacitor, CREF(2)
MAX
16.5
10 x CREF
0.1
1.0
Timing capacitor, CT (for 500 kHz switching frequency)
220
Timing resistor, RT (for 500 kHz switching frequency)
82
Delay resistor RDEL_AB, RDEL_CD
2.5
UNIT
V
µF
F
pF
40
kΩ
Operating junction temperature, TJ(4)
−55
125
°C
(1) The VDD capacitor should be a low ESR, ESL ceramic capacitor located directly across the VDD and PGND pins. A larger bulk capacitor should
belocated as physically close as possible to the VDD pins.
(2) The VREF capacitor should be a low ESR, ESL ceramic capacitor located directly across the REF and GND pins. If a larger capacitor is desired
for the VREF then it should be located near the VREF cap and connected to the VREF pin with a resistor of 51 Ω or greater. The bulk capacitor on
VDD must be a factor of 10 greater than the total VREF capacitance.
(3) It is recommended that there be a single point grounded between GND and PGND directly under the device. There should be a seperate ground
plane associated with the GND pin and all components associated with pins 1 through 12 plus 19 and 20 be located over this ground plane. Any
connections associated with these pins to ground should be connected to this ground plane.
(4) It is not recommended that the device operate under conditions beyond those specified in this table for extended periods of time.
www.ti.com
3
SLUS157L − DECEMBER 1999 − REVISED APRIL 2008
ELECTRICAL CHARACTERISTICS VDD = 12 V, RT = 82 kΩ, CT = 220 pF, RDELAB = 10 kΩ, RDELCD = 10 kΩ, CREF = 0.1 µF,
CVDD = 0.1 µF and no load on the outputs, TA = TJ. TA = 0°C to 70°C for UCC3895x, TA = −40°C to 85°C for UCC2895x and TA = −55°C to 125°C
for the UCC1895x. (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
UVLO (UNDERVOLTAGE LOCKOUT)
UVLO(on)
Start-up voltage threshold
10.2
11
11.8
UVLO(off)
Minimum operating voltage after
start-up
8.2
9
9.8
UVLO(hys)
SUPPLY
Hysteresis
1.0
2.0
3.0
ISTART
IDD
Start-up current
150
250
µA
5
6
mA
VDD = 8 V
Operating current
VDD_CLAMP VDD clamp voltage
VOLTAGE REFERENCE
IDD = 10 mA
16.5
17.5
18.5
4.94
5.00
5.06
4.85
5
5.15
10
20
VREF
Output voltage
TJ = 25°C
10 V < VDD < VDD_CLAMP,
0 mA < IREF < 5 mA,
temperature
ISC
Short circuit current
REF = 0 V,
TJ = 25°C
V
V
V
mA
ERROR AMPLIFIER
Common-mode input voltage range
−0.1
3.6
V
VIO
IBIAS
Offset voltage
−7
7
mV
Input bias current (EAP, EAN)
−1
1
µA
EAOUT_VOH
High-level output voltage
EAP−EAN = 500 mV,
EAOUT_VOL
Low-level output voltage
EAP−EAN = −500 mV, IEAOUT = 0.5 mA
ISOURCE
ISINK
Error amplifier output source current
EAP−EAN = 500 mV,
Error amplifier output sink current
AVOL
Open-loop dc gain
75
85
dB
GBW
Unity gain bandwidth(1)
5.0
7.0
MHz
1.5
2.2
V/µs
No-load comparator turn-off
threshold
0.45
0.50
0.55
No-load comparator turn-on
threshold
0.55
0.60
0.69
0.035
0.10
0.165
Slew rate(1)
IEAOUT = −0.5 mA
4.0
4.5
5.0
0
0.2
0.4
EAOUT = 2.5 V
1.0
1.5
EAP−EAN = −500 mV, EAOUT = 2.5 V
2.5
4.5
1 V < EAN < 0 V,
EAP = 500 mV
0.5 V < EAOUT < 3.0 V
No-load comparator hysteresis
V
mA
V
OSCILLATOR
fOSC
Frequency
Frequency total variation(1)
VIH_SYNC
VOH_SYNC
SYNC input threshold, SYNC
VOL_SYNC
Low-level output voltage, SYNC
High-level output voltage, SYNC
Sync output pulse width
4
ISYNC = −400 µA,
ISYNC = 100 µA,
VCT = 2.6 V
VCT = 0.0 V
LOADSYNC = 3.9 kΩ and 30 pF in parallel
473
500
527
2.5%
5%
2.05
2.10
2.40
4.1
4.5
5.0
0.0
0.5
1.0
85
135
2.9
3
3.1
Timing capacitor peak voltage
2.25
2.35
2.55
Timing capacitor valley voltage
0.0
0.2
0.4
VRT
VCT(peak)
Timing resistor voltage
VCT(valley)
(1)
TJ = 25°C
Over line, temperature
Ensured by design. Not production tested.
www.ti.com
kHz
V
ns
V
SLUS157L − DECEMBER 1999 − REVISED APRIL 2008
ELECTRICAL CHARACTERISTICS VDD = 12 V, RT = 82 kΩ, CT = 220 pF, RDELAB = 10 kΩ, RDELCD = 10 kΩ, CREF = 0.1 µF,
CVDD = 0.1 µF and no load on the outputs, TA = TJ. TA = 0°C to 70°C for UCC3895x, TA = −40°C to 85°C for UCC2895x and TA = −55°C to 125°C
for the UCC1895x. (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
20
µA
1.90
2.00
2.10
V
2.4
2.5
2.6
V
75
110
ns
CURRENT SENSE
ICS(bias)
Current sense bias current
0 V < CS < 2.5 V,
0 V ADS < 2.5 V
Peak current threshold
Overcurrent threshold
−4.5
0V ≤ CS ≤ 2.3 V,
DELAB=DELCD=REF
Softstart source current
SS/DISB = 3.0 V,
CS = 1.9 V
−40
−35
−30
µA
Softstart sink current
SS/DISB = 3.0 V,
CS = 2.6 V
325
350
375
µA
0.44
0.50
0.56
V
0.45
0.50
0.55
V
Current sense to output delay
SOFT-START/SHUTDOWN
ISOURCE
ISINK
Softstart/disable comparator threshold
ADAPTIVE DELAY SET (ADS)
ADS = CS = 0 V
DELAB/DELCD output voltage
tDELAY
ADS = 0 V,
CS = 2.0 V
Output delay(1)(3)
ADS = CS = 0 V
ADS bias current
0 V < ADS < 2.5 V,
0 V < CS < 2.5 V
High−level output voltage (all outputs)
IOUT = −10 mA,
IOUT = 10 mA
VDD to output
1.9
2.0
2.1
V
450
560
620
ns
20
µA
250
400
mV
−20
OUTPUT
VOH
VOL
tR
Low-level output voltage (all outputs)
Rise time(1)
tF
Fall time(1)
(1) Ensured by design. Not production tested.
(2) Minimum phase shift is defined as:
t f (OUTC) * t f (OUTA)
F + 180
or F + 180
t PERIOD
150
250
mV
CLOAD = 100 pF
20
35
ns
CLOAD = 100 pF
20
35
ns
t f (OUTC) * t f (OUTB)
t PERIOD
where
tf(OUTA) = falling edge of OUTA signal, tf(OUTB) = falling edge of OUTB signal
tf(OUTC) = falling edge of OUTC signal, tf(OUTD) = falling edge of OUTD signal
tPERIOD = period of OUTA or OUTB signal
(3) Output delay is measured between OUTA/OUTB or OUTC/OUTD. Output delay is defined as shown below where:
tf(OUTA) = falling edge of OUTA signal, tr(OUTB) = rising edge of OUTB signal
tPERIOD
OUTA
OUTA
tDELAY = tR(OUTB) − tf(OUTA)
tDELAY = tf(OUTC) − tf(OUTA)
OUTB
OUTC
Same applies to OUTB and OUTD
Same applies to OUTC and OUTD
www.ti.com
5
SLUS157L − DECEMBER 1999 − REVISED APRIL 2008
ELECTRICAL CHARACTERISTICS VDD = 12 V, RT = 82 kΩ, CT = 220 pF, RDELAB = 10 kΩ, RDELCD = 10 kΩ, CREF = 0.1 µF,
CVDD = 0.1 µF and no load on the outputs, TA = TJ. TA = 0°C to 70°C for UCC3895x, TA = −40°C to 85°C for UCC2895x and TA = 55°C to 125°C
for the UCC1895x. (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
V
PWM COMPARATOR
tDELAY
IR(bias)
IR(sink)
EAOUT to RAMP input offset voltage
Minimum phase shift(2)
(OUTA to OUTC, OUTB to OUTD)
RAMP = 0 V,
DELAB=DELCD=REF
0.72
0.85
1.05
RAMP = 0 V
EAOUT = 650 mV
.0%
.85%
1.4%
Delay(3)
(RAMP to OUTC, RAMP to OUTD)
0 V < RAMP < 2.5 V, EAOUT = 1.2 V,
DELAB=DELCD=REF
70
120
ns
RAMP bias current
RAMP < 5 V,
CT = 2.2 V
−5
5
µA
RAMP sink current
RAMP = 5 V,
CT = 2.6 V
12
19
mA
TERMINAL FUNCTIONS
TERMINAL
NAME
NO.
I/O
DESCRIPTION
ADS
11
I
Adaptive delay set. Sets the ratio between the maximum and minimum programmed output delay dead time.
CS
12
I
Current sense input for cycle-by-cycle current limiting and for over-current comparator.
CT
7
I
Oscillator timing capacitor for programming the switching frequency. The UCC3895’s oscillator charges CT
via a programmed current.
DELAB
9
I
Delay programming between complementary outputs. DELAB programs the dead time between switching of
output A and output B.
DELCD
10
I
Delay programming between complementary outputs. DELCD programs the dead time between switching of
output C and output D.
EAOUT
2
I/O
EAP
20
I
Non-inverting input to the error amplifier. Keep below 3.6 volts for proper operation.
EAN
1
I
Inverting input to the error amplifier. Keep below 3.6 volts for proper operation.
Chip ground for all circuits except the output stages.
Error amplifier output.
GND
5
−
OUTA
18
O
OUTB
17
O
OUTC
14
O
OUTD
13
O
PGND
16
−
Output stage ground.
RAMP
3
I
Inverting input of the PWM comparator.
REF
4
O
5 V, ±1.2%, 5 mA voltage reference. For best performance, bypass with a 0.1-µF low ESR, low ESL capacitor
to ground. Do not use more than 1.0 µF of total capacitance on this pin.
RT
8
I
Oscillator timing resistor for programming the switching frequency.
SS/DISB
19
I
Soft-start/disable. This pin combines the two independent functions.
SYNC
6
I/O
VDD
15
I
6
The four outputs are 100-mA complementary MOS drivers, and are optimized to drive FET driver circuits
such as UCC27424 or gate drive transformers.
Oscillator synchronization. This pin is bidirectional.
Power supply input pin. VDD must be bypassed with a minimum of a 1.0-µF low ESR, low ESL capacitor to
ground. The addition of a 10−µF low ESR, low ESL between VDD and PGND is recommended.
www.ti.com
SLUS157L − DECEMBER 1999 − REVISED APRIL 2008
BLOCK DIAGRAM
IRT
RT
Q
8
8(IRT )
CT
7
15
D S Q
OSC
Q
D SQ
R Q
SYNC
6
RAMP
3
D S Q
DELAY C
2
EAP
20
EAN
1
ERROR
AMP
+
2V
CS
DELAY B
DELAB
17
OUTB
NO LOAD
COMPARATOR
+
CURRENT SENSE
COMPARATOR
+
R Q
14
DELAY D
+
OVER CURRENT
COMPARATOR
IRT
10
DELCD
13
OUTD
16
PGND
11
ADS
4
REF
5
GND
ADAPTIVE DELAY
SET AMPLIFIER
+
REF
OUTC
0.5 V / 0.6 V
12
2.5 V
Q
S
Q
R
+
11 V / 9 V
DISABLE
COMPARATOR
HI = ON
19
0.5V
UVLO COMPARATOR
REF
0.5 V
SS
9
+
0.8 V
EAOUT
R Q
OUTA
+
PWM
COMPARATOR
18
DELAY A
VDD
REFERENCE OK
COMPARATOR
+
4V
HI = ON
+
10(IRT)
UDG−98140
REF
RT
RT
VREF
8 x IRT
IRT
CT
CLOCK
2.5 V
S
Q
+
CT
SYNC
R
0.2 V
+
CLOCK
UDG−03135
Figure 1. Oscillator Block Diagram
www.ti.com
7
SLUS157L − DECEMBER 1999 − REVISED APRIL 2008
REF
0.5 V
75 kΩ
100 kΩ
CS
TO DELAY A
AND DELAY B
BLOCKS
+
+
DELAB
100 kΩ
ADS
75 kΩ
REF
+
TO DELAY C
AND DELAY D
BLOCKS
DELCD
UDG−98141
Figure 2. Adaptive Delay Set Block Diagram
REF
BUSSED CURRENT
FROM ADS CIRCUIT
3.5 V
DELAB/CD
FROM PAD
DELAYED
CLOCK
SIGNAL
2.5 V
CLOCK
UDG−03132
Figure 3. Delay Block Diagram (One Delay Block Per Outlet)
8
www.ti.com
SLUS157L − DECEMBER 1999 − REVISED APRIL 2008
DETAILED PIN DESCRIPTION
Adaptive Delay Set (ADS)
This function sets the ratio between the maximum and minimum programmed output-delay dead time. When
the ADS pin is directly connected to the CS pin, no delay modulation occurs. The maximum delay modulation
occurs when ADS is grounded. In this case, delay time is four times longer when CS = 0 than when CS = 2.0 V
(the peak-current threshold), ADS changes the output voltage on the delay pins DELAB and DELCD by the
following formula:
ƪ
V DEL + 0.75
ǒVCS * VADSǓƫ ) 0.5 V
(1)
where VCS and VADS are in volts. ADS must be limited to between 0 V and 2.5 V and must be less than or equal
to CS. DELAB and DELCD are clamped to a minimum of 0.5 V.
Current Sense (CS)
The inverting input of the current-sense comparator and the non-inverting input of the overcurrent comparator
and the ADS amplifier. The current sense signal is used for cycle-by-cycle current limiting in peak current mode
control, and for overcurrent protection in all cases with a secondary threshold for output shutdown. An output
disable initiated by an overcurrent fault also results in a restart cycle, called soft stop, with full soft start.
Oscillator Timing Capacitor (CT)
The UCC3895’s oscillator charges CT via a programmed current. The waveform on CT is a sawtooth, with a peak
voltage of 2.35 V. The approximate oscillator period is calculated by the following formula:
t OSC +
5
RT
48
CT
) 120 ns
(2)
where CT is in Farads, and RT is in Ohms and tOSC is in seconds. CT can range from 100 pF to 880 pF.
NOTE: A large CT and a small RT combination results in extended fall times on the CT waveform.
The increased fall time increases the SYNC pulse width, hence limiting the maximum phase shift
between OUTA, OUTB and OUTC, OUTD outputs, which limits the maximum duty cycle of the
converter. (Refer to Figure 1)
Delay Programming Between Complementary Outputs (DELAB, DELCD)
DELAB programs the dead time between switching of OUTA and OUTB, and DELCD programs the dead time
between OUTC and OUTD. This delay is introduced between complementary outputs in the same leg of the
external bridge. The UCC2895N allows the user to select the delay, in which the resonant switching of the external
power stages takes place. Separate delays are provided for the two half-bridges to accommodate differences in
resonant-capacitor charging currents. The delay in each stage is set according to the following formula:
t DELAY +
(25
10 *12)
V DEL
R DEL
) 25 ns
(3)
where VDEL (V), and RDEL is in (Ω) and tDELAY is in seconds. DELAB and DELCD can source about 1 mA
maximum. Choose the delay resistors so that this maximum is not exceeded. Programmable output delay is
defeated by tying DELAB and/or DELCD to REF. For an optimum performance keep stray capacitance on these
pins at less than 10 pF.
www.ti.com
9
SLUS157L − DECEMBER 1999 − REVISED APRIL 2008
DETAILED PIN DESCRIPTION (continued)
Error Amplifier (EAOUT), (EAP), (EAN)
EAOUT connected internally to the non-inverting input of the PWM comparator and the no-load comparator.
EAOUT is internally clamped to the soft-start voltage. The no-load comparator shuts down the output stages
when EAOUT falls below 500 mV, and allows the outputs to turn on again when EAOUT rises above 600 mV.
EAP is the non−inverting and the EAN is the inverting input to the error amplifier.
Output MOSFET Drivers (OUTA, OUTB, OUTC, OUTD)
The 4 outputs are 100-mA complementary MOS drivers, and are optimized to drive MOSFET driver circuits.
OUTA and OUTB are fully complementary, (assuming no programming delay). They operate near 50% duty
cycle and one-half the oscillator frequency. OUTA and OUTB are intended to drive one half-bridge circuit in an
external power stage. OUTC and OUTD drive the other half-bridge and have the same characteristics as OUTA
and OUTB. OUTC is phase shifted with respect to OUTA, and OUTD is phase shifted with respect to OUTB.
NOTE: Changing the phase relationship of OUTC and OUTD with respect to OUTA and OUTB
requires other than the nominal 50% duty ratio on OUTC and OUTD during those transients.
Power Ground (PGND)
To keep output switching noise from critical analog circuits, the UCC3895 has two different ground connections.
PGND is the ground connection for the high-current output stages. Both GND and PGND must be electrically
tied together. Also, since PGND carries high current, board traces must be low impedance.
Inverting Input of the PWM Comparator (RAMP)
This pin receives either the CT waveform in voltage and average current-mode controls, or the current signal
(plus slope compensation) in peak current-mode control.
Voltage Reference (REF)
The 5 V, ± 1.2% reference supplies power to internal circuitry, and can also supply up to 5 mA to external loads.
The reference is shut down during undervoltage lockout but is operational during all other disable modes. For
best performance, bypass with a 0.1-µF, low-ESR, low-ESL capacitor to GND. Do not use more than 1.0 µF of
total capacitance on this pin. To ensure the stability of the internal reference.
Oscillator Timing Resistor (RT)
The oscillator in the UCC3895 operates by charging an external timing capacitor, CT, with a fixed current
programmed by RT. RT current is calculated as follows:
I RT (A) + 3.0 V
R T (W)
(4)
RT can range from 40 kΩ to 120 kΩ. Soft-start charging and discharging currents are also programmed by IRT
(Refer to Figure 1).
Analog Ground (GND)
This pin is the chip ground for all internal circuits except the output stages.
10
www.ti.com
SLUS157L − DECEMBER 1999 − REVISED APRIL 2008
DETAILED PIN DESCRIPTION (continued)
Soft-Start/Disable (SS/DISB)
This pin combines two independent functions.
Disable Mode: A rapid shutdown of the chip is accomplished by externally forcing SS/DISB below 0.5 V,
externally forcing REF below 4 V, or if VDD drops below the undervoltage lockout threshold. In the case of REF
being pulled below 4 V or an undervoltage condition, SS/DISB is actively pulled to ground via an internal
MOSFET switch.
If an overcurrent fault is sensed (CS = 2.5 V), a soft-stop is initiated. In this mode, SS/DISB sinks a constant
current of (10 × IRT). The soft-stop continues until SS/DISB falls below 0.5 V. When any of these faults are
detected, all outputs are forced to ground immediately.
NOTE:If SS/DISB is forced below 0.5 V, the pin starts to source current equal to IRT. The only time
the part switches into low IDD current mode, though, is when the part is in undervoltage lockout.
Soft-start Mode: After a fault or disable condition has passed, VDD is above the start threshold, and/or
SS/DISB falls below 0.5 V during a soft-stop, SS/DISB switches to a soft-start mode. The pin then sources
current, equal to IRT. A user-selected resistor/capacitor combination on SS/DISB determines the soft start time
constant.
NOTE: SS/DISB actively clamps the EAOUT pin voltage to approximately the SS/DISB pin voltage
during both soft-start, soft-stop, and disable conditions.
Oscillator Synchronization (SYNC)
This pin is bidirectional (refer to Figure 1). When used as an output, SYNC can be used as a clock, which is the
same as the device’s internal clock. When used as an input, SYNC overrides the chip’s internal oscillator and
act as it’s clock signal. This bidirectional feature allows synchronization of multiple power supplies. Also, the
SYNC signal internally discharge the CT capacitor and any filter capacitors that are present on the RAMP pin.
The internal SYNC circuitry is level sensitive, with an input-low threshold of 1.9 V, and an input-high threshold
of 2.1 V. A resistor as small as 3.9 kΩ may be tied between SYNC and GND to reduce the sync pulse width.
Chip Supply (VDD)
This is the input pin to the chip. VDD must be bypassed with a minimum of 1.0 µF low ESR, low ESL capacitor
to ground. The addition of a 10−µF low ESR, low ESL between VDD and PGND is recommended.
www.ti.com
11
SLUS157L − DECEMBER 1999 − REVISED APRIL 2008
APPLICATION INFORMATION
Programming DELAB, DELCD and the Adaptive Delay Set
The UCC2895N allows the user to set the delay between switch commands within each leg of the full-bridge
power circuit according to equations:
t DELAY +
(25
10 *12)
V DEL
R DEL
) 25 ns
(5)
From this equation VDEL is determined in conjunction with the desire to use (or not) the adaptive delay set
feature from the following formula:
ƪ
V DEL + 0.75
ǒVCS * VADSǓƫ ) 0.5 V
(6)
The following diagram illustrates the resistors needed to program the delay periods and the adaptive delay set
function.
UCC3895
9
DELAB
10
DELCD
CS
12
ADS
11
RDELAB
RDELCD
Figure 4. Programming Adaptive Delay Set
The adaptive delay set feature (ADS) allows the user to vary the delay times between switch commands
within each of the converter’s two legs. The delay-time modulation is implemented by connecting ADS
(pin 11) to CS, GND, or a resistive divider from CS through ADS to GND to set VADS as shown in Figure 4.
From equation (6) for VDEL, if ADS is tied to GND then VDEL rises in direct proportion to VCS, causing a
decrease in tDELAY as the load increases. In this condition, the maximum value of VDEL is 2 V.
If ADS is connected to a resistive divider between CS and GND, the term (VCS−VADS) becomes smaller,
reducing the level of VDEL. This decreases the amount of delay modulation. In the limit of ADS tied to CS,
VDEL = 0.5 V and no delay modulation occurs. Figure 5 graphically shows the delay time vs. load for
varying adaptive delay set feature voltages (VADS).
In the case of maximum delay modulation (ADS=GND), when the circuit goes from light load to heavy
load, the variation of VDEL is from 0.5 V to 2 V. This causes the delay times to vary by a 4:1 ratio as the
load is changed.
The ability to program an adaptive delay is a desirable feature because the optimum delay time is a
function of the current flowing in the primary winding of the transformer, and can change by a factor of
10:1 or more as circuit loading changes. Reference[5] describes the many interrelated factors for choosing
the optimum delay times for the most efficient power conversion, and illustrates an external circuit to
enable adaptive delay set using the UC3879. Implementing this adaptive feature is simplified in the
UCC3895 controller, giving the user the ability to tailor the delay times to suit a particular application with a
minimum of external parts.
12
www.ti.com
SLUS157L − DECEMBER 1999 − REVISED APRIL 2008
APPLICATION INFORMATION
DELAY TIME
vs
CURRENT SENSE VOLTAGE
A = VADS/VCS
RDELAY = 10 kΩ
A = 1.0
td − Delay Time − ns
500
400
A = 0.8
300
A = 0.6
200
A = 0.4
A = 0.2
A = 0.1
100
0
0.5
1.0
1.5
2.0
2.5
VCS − Current Sense Voltage − V
Figure 5. Delay Time Under Varying ADS Voltages
CLOCK
RAMP
&
COMP
PWM
SIGNAL
OUTPUT A
OUTPUT B
OUTPUT C
UDG−99138
OUTPUT D
Figure 6. UCC3895 Timing Diagram (No Output Delay Shown, COMP to RAMP offset not included)
www.ti.com
13
SLUS157L − DECEMBER 1999 − REVISED APRIL 2008
TYPICAL CHARACTERISTICS
OUTPUT DELAY
vs
OSCILLATOR FREQUENCY
vs
DELAY RESISTANCE
TIMING CAPACITANCE
2000
1600
VCS = 0 V
fSW − Switching Frequency − kHz
1800
1400
1200
1000
800
600
VCS = 2 V
RT = 62 kW
1400
1200
RT = 47 kW
1000
800
600
400
400
200
RT = 100 kW
200
RT = 82 kW
0
0
0
10
20
30
RDEL − Delay Resistor − kΩ
100
40
Figure 7
Figure 8
EAOUT to RAMP OFFSET
vs
AMPLIFIER GAIN AND PHASE MARGIN
vs
TEMPERATURE
FREQUENCY
1.00
200
100
GAIN
80
0.95
Gain − dB
VOFFSET − EAOUT to RAMP Offset − V
1000
CT − Timing Capacitance − pF
0.90
120
60
80
40
PHASE
MARGIN
0.85
40
20
0.80
−55
−35
−15 5
25
45 65
TA − Temperature − °C
85
105
125
0
1
0
10
1k
100
10 k
100 k 1 MHz 10 MHz
fOSC − Oscillator Frequency − kHz
Figure 10
Figure 9
14
160
www.ti.com
Phase Margin − Degrees
tDELAY − Output Delay − ns
1600
SLUS157L − DECEMBER 1999 − REVISED APRIL 2008
TYPICAL CHARACTERISTICS
INPUT CURRENT
vs
INPUT CURRENT
vs
OSCILLATOR FREQUENCY
9
0.1-nF OUTPUT LOADS
12
VDD = 15 V
IDD − Operating Current − mA
IDD − Operating Current − mA
8
7
OSCILLATOR FREQUENCY
13
NO OUTPUT LOADING
VDD = 17 V
6
VDD = 15 V
11
10
5
9
VDD = 17 V
8
7
VDD = 12 V
6
VDD = 10 V
5
VDD = 10 V
VDD = 12 V
4
0
400
800
1200
1600
fOSC − Oscillator Frequency − kHz
4
0
400
800
1200
1600
fOSC − Oscillator Frequency − kHz
Figure 11
Figure 12
REFERENCES
1. M. Dennis, A Comparison Between the BiCMOS UCC3895 Phase Shift Controller and the UC3875
Application Note (SLUA246).
2. L. Balogh, The Current−Doubler Rectifier: An Alternative Rectification Technique for Push−Pull and Bridge
Converters Application Note (SLUA121).
3. W. Andreycak, Phase Shifted, Zero Voltage Transition Design Considerations, Application Note
(SLUA107).
4. L. Balogh, The New UC3879 Phase Shifted PWM Controller Simplifies the Design of Zero Voltage
Transition Full−Bridge Converters, Application Note (SLUA122).
5. L. Balogh, Design Review: 100 W, 400 kHz, dc-to-dc Converter with Current Doubler Synchronous
Rectification Achieves 92% Efficiency, Unitrode Power Supply Design Seminar Manual, SEM−1100, 1996,
Topic 2.
6. UC3875 Phase Shift Resonant Controller, Datasheet, (SLUS229).
7. UC3879 Phase Shift Resonant Controller, Datasheet, (SLUS230).
8. UCC3895EVM−1, “Configuring the UCC3895 for direct Control Driven Synchronous Rectification, (Texas
Instrument’s Literature Number SLUU109A)
9. UCC3895, CD Output Asymetrical Duty Cycle Operation, (Texas Instrument’s Literature Number SLUA275)
10. Texas Instrument’s Literature Number SLUA323
11. Synchronous Rectifiers of a Current Doubler, (Texas Instrument’s Literature Number SLUA287)
www.ti.com
15
PACKAGE OPTION ADDENDUM
www.ti.com
18-Sep-2008
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
Lead/Ball Finish
UCC1895J
ACTIVE
CDIP
J
20
1
TBD
UCC1895L
ACTIVE
LCCC
FK
20
1
TBD
UCC2895DW
ACTIVE
SOIC
DW
20
25
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UCC2895DWG4
ACTIVE
SOIC
DW
20
25
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UCC2895DWTR
ACTIVE
SOIC
DW
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UCC2895DWTRG4
ACTIVE
SOIC
DW
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UCC2895N
ACTIVE
PDIP
N
20
20
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
UCC2895NG4
ACTIVE
PDIP
N
20
20
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
UCC2895PW
ACTIVE
TSSOP
PW
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UCC2895PWG4
ACTIVE
TSSOP
PW
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UCC2895PWTR
ACTIVE
TSSOP
PW
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UCC2895PWTRG4
ACTIVE
TSSOP
PW
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UCC2895Q
ACTIVE
PLCC
FN
20
46
Green (RoHS &
no Sb/Br)
CU SN
Level-2-260C-1 YEAR
UCC2895QG3
ACTIVE
PLCC
FN
20
46
Green (RoHS &
no Sb/Br)
CU SN
Level-2-260C-1 YEAR
UCC3895DW
ACTIVE
SOIC
DW
20
25
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UCC3895DWG4
ACTIVE
SOIC
DW
20
25
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UCC3895DWTR
ACTIVE
SOIC
DW
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UCC3895DWTRG4
ACTIVE
SOIC
DW
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UCC3895N
ACTIVE
PDIP
N
20
20
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
UCC3895NG4
ACTIVE
PDIP
N
20
20
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
UCC3895PW
ACTIVE
TSSOP
PW
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UCC3895PWG4
ACTIVE
TSSOP
PW
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UCC3895PWTR
ACTIVE
TSSOP
PW
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UCC3895PWTRG4
ACTIVE
TSSOP
PW
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
UCC3895Q
ACTIVE
PLCC
FN
20
46
Green (RoHS &
no Sb/Br)
CU SN
Level-2-260C-1 YEAR
UCC3895QG3
ACTIVE
PLCC
FN
20
46
Green (RoHS &
CU SN
Level-2-260C-1 YEAR
Addendum-Page 1
A42 SNPB
MSL Peak Temp (3)
N / A for Pkg Type
POST-PLATE N / A for Pkg Type
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
18-Sep-2008
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
Lead/Ball Finish
MSL Peak Temp (3)
no Sb/Br)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF UCC1895, UCC2895, UCC3895 :
UCC2895-Q1
• Automotive:
• Enhanced Product: UCC2895-EP
NOTE: Qualified Version Definitions:
- Q100 devices qualified for high-reliability automotive applications targeting zero defects
• Automotive
• Enhanced Product - Supports Defense, Aerospace and Medical Applications
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
29-Jul-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
UCC2895DWTR
SOIC
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
13.0
2.7
12.0
24.0
Q1
DW
20
2000
330.0
24.4
10.8
UCC2895PWTR
TSSOP
PW
20
2000
330.0
16.4
6.95
7.1
1.6
8.0
16.0
Q1
UCC3895DWTR
SOIC
DW
20
2000
330.0
24.4
10.8
13.0
2.7
12.0
24.0
Q1
UCC3895PWTR
TSSOP
PW
20
2000
330.0
16.4
6.95
7.1
1.6
8.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
29-Jul-2008
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
UCC2895DWTR
SOIC
DW
20
2000
346.0
346.0
41.0
UCC2895PWTR
TSSOP
PW
20
2000
346.0
346.0
33.0
UCC3895DWTR
SOIC
DW
20
2000
346.0
346.0
41.0
UCC3895PWTR
TSSOP
PW
20
2000
346.0
346.0
33.0
Pack Materials-Page 2
MECHANICAL DATA
MLCC006B – OCTOBER 1996
FK (S-CQCC-N**)
LEADLESS CERAMIC CHIP CARRIER
28 TERMINAL SHOWN
18
17
16
15
14
13
NO. OF
TERMINALS
**
12
19
11
20
10
A
B
MIN
MAX
MIN
MAX
20
0.342
(8,69)
0.358
(9,09)
0.307
(7,80)
0.358
(9,09)
28
0.442
(11,23)
0.458
(11,63)
0.406
(10,31)
0.458
(11,63)
21
9
22
8
44
0.640
(16,26)
0.660
(16,76)
0.495
(12,58)
0.560
(14,22)
23
7
52
0.739
(18,78)
0.761
(19,32)
0.495
(12,58)
0.560
(14,22)
24
6
68
0.938
(23,83)
0.962
(24,43)
0.850
(21,6)
0.858
(21,8)
84
1.141
(28,99)
1.165
(29,59)
1.047
(26,6)
1.063
(27,0)
B SQ
A SQ
25
5
26
27
28
1
2
3
4
0.080 (2,03)
0.064 (1,63)
0.020 (0,51)
0.010 (0,25)
0.020 (0,51)
0.010 (0,25)
0.055 (1,40)
0.045 (1,14)
0.045 (1,14)
0.035 (0,89)
0.045 (1,14)
0.035 (0,89)
0.028 (0,71)
0.022 (0,54)
0.050 (1,27)
4040140 / D 10/96
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
This package can be hermetically sealed with a metal lid.
The terminals are gold plated.
Falls within JEDEC MS-004
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MPLC004A – OCTOBER 1994
FN (S-PQCC-J**)
PLASTIC J-LEADED CHIP CARRIER
20 PIN SHOWN
Seating Plane
0.004 (0,10)
0.180 (4,57) MAX
0.120 (3,05)
0.090 (2,29)
D
D1
0.020 (0,51) MIN
3
1
19
0.032 (0,81)
0.026 (0,66)
4
E
18
D2 / E2
E1
D2 / E2
8
14
0.021 (0,53)
0.013 (0,33)
0.007 (0,18) M
0.050 (1,27)
9
13
0.008 (0,20) NOM
D/E
D2 / E2
D1 / E1
NO. OF
PINS
**
MIN
MAX
MIN
MAX
MIN
MAX
20
0.385 (9,78)
0.395 (10,03)
0.350 (8,89)
0.356 (9,04)
0.141 (3,58)
0.169 (4,29)
28
0.485 (12,32)
0.495 (12,57)
0.450 (11,43)
0.456 (11,58)
0.191 (4,85)
0.219 (5,56)
44
0.685 (17,40)
0.695 (17,65)
0.650 (16,51)
0.656 (16,66)
0.291 (7,39)
0.319 (8,10)
52
0.785 (19,94)
0.795 (20,19)
0.750 (19,05)
0.756 (19,20)
0.341 (8,66)
0.369 (9,37)
68
0.985 (25,02)
0.995 (25,27)
0.950 (24,13)
0.958 (24,33)
0.441 (11,20)
0.469 (11,91)
84
1.185 (30,10)
1.195 (30,35)
1.150 (29,21)
1.158 (29,41)
0.541 (13,74)
0.569 (14,45)
4040005 / B 03/95
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-018
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated