TI UCC38086DRG4

 SLUS488E − SEPTEMBER 2002 − REVISED JULY 2009
FEATURES
APPLICATIONS
D
D
D
D
D
D
D
D
D
D
D
D
D
Programmable Slope Compensation
Internal Soft-Start on the UCC38083/4
Cycle-by-Cycle Current Limiting
Low Start-Up Current of 120 µA and 1.5 mA
Typical Run Current
Single External Component Oscillator
Programmable from 50 kHz to 1 MHz
High-Current Totem-Pole Dual Output Stage
Drives Push-Pull Configuration with 1-A Sink
and 0.5-A Source Capability
Current Sense Discharge Transistor to
Improve Dynamic Response
Internally Trimmed Bandgap Reference
Undervoltage Lockout with Hysteresis
BASIC APPLICATION
V IN
POWER
TRANSFORMER
VDD
UCC3808x
CTRL
OUTA
RT
OUTB
CS
R SET
CF
The UCC38083/4/5/6 is a family of BiCMOS pulse width
modulation (PWM) controllers for dc-to-dc or off-line
fixed-frequency current-mode switching power
supplies. The dual output stages are configured for the
push-pull topology. Both outputs switch at half the
oscillator frequency using a toggle flip-flop. The dead
time between the two outputs is typically 110 ns, limiting
each output’s duty cycle to less than 50%.
The new UCC3808x family is based on the UCC3808A
architecture. The major differences include the addition
of a programmable slope compensation ramp to the CS
signal and the removal of the error amplifier. The current
flowing out of the ISET pin through an external resistor
is monitored internally to set the magnitude of the slope
V OUT compensation function. This device also includes an
internal discharge transistor from the CS pin to ground,
which is activated at each clock cycle after the pulse is
terminated. This discharges any filter capacitance on
the CS pin during each cycle and helps minimize filter
capacitor values and current sense delay.
The UCC38083 and the UCC38085 devices have the
turn-on/off thresholds of 12.5 V / 8.3 V, while the
UCC38084 and the UCC38086 has the turn-on/off
thresholds of 4.3 V / 4.1 V. Each device is offered in 8-pin
TSSOP (PW), 8-pin SOIC (D) and 8-pin PDIP (P)
packages.
GND
RT
DESCRIPTION
The UCC38083 and the UCC38084 devices have a
typical soft-start interval time of 3.5 ms while the
UCC38085 and the UCC38086 has less than 100 µs for
applications where internal soft-start is not desired.
RF
ISET
High-Efficiency Switch-Mode Power Supplies
Telecom dc-to-dc Converters
Point-of-Load or Point-of-Use Power Modules
Low-Cost Push-Pull and Half-Bridge
Applications
RS
FEEDBACK
UDG−01080
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments
semiconductor products and disclaimers thereto appears at the end of this data sheet.
!"#$ % &'!!($ #% )'*+&#$ ,#$(!,'&$% &!" $ %)(&&#$% )(! $.( $(!"% (/#% %$!'"($%
%$#,#!, 0#!!#$1- !,'&$ )!&(%%2 ,(% $ (&(%%#!+1 &+',(
$(%$2 #++ )#!#"($(!%-
Copyright  2002−2009, Texas Instruments Incorporated
www.ti.com
1
SLUS488E − SEPTEMBER 2002 − REVISED JULY 2009
ORDERING INFORMATION
THERMAL RESISTANCE TABLE
PACKAGE
θjc(°C/W)
SOIC−8 (D)
42
PDIP−8 (P)
50
32(2)
θja(°C/W)
84 to 160(1)
110(1)
232 to 257(2)
NOTES: (1) Specified θja (junction to ambient) is for devices mounted to 5-inch2 FR4 PC board
with one ounce copper where noted. When resistance range is given, lower values
are for 5 inch2 aluminum PC board. Test PWB was 0.062 inch thick and typically
used 0.635-mm trace widths for power packages and 1.3-mm trace widths for
non-power packages with a 100-mil x 100-mil probe land area at the end of each
trace.
(2). Modeled data. If value range given for θja, lower value is for 3x3 inch. 1 oz internal
copper ground plane, higher value is for 1x1-inch. ground plane. All model data
assumes only one trace for each non-fused lead.
TSSOP−8 (PW)
AVAILABLE OPTIONS
INTERNAL
SOFT START
TA
3.5 ms
−40°C to 85°C
75 µs
3.5 ms
0°C to 70°C
75 µs
UVLO
PACKAGES
ON
OFF
SOIC-8 (D)
PDIP-8 (P)
TSSOP-8 (PW)
12.5 V
8.3 V
UCC28083D
UCC28083P
UCC28083PW
4.3 V
4.1 V
UCC28084D
UCC28084P
UCC28084PW
12.5 V
8.3 V
UCC28085D
UCC28085P
UCC28085PW
4.3 V
4.1 V
UCC28086D
UCC28086P
UCC28086PW
12.5 V
8.3 V
UCC38083D
UCC38083P
UCC38083PW
4.3 V
4.1 V
UCC38084D
UCC38084P
UCC38084PW
12.5 V
8.3 V
UCC38085D
UCC38085P
UCC38085PW
4.3 V
4.1 V
UCC38086D
UCC38086P
UCC38086PW
† The D and PW packages are available taped and reeled. Add R suffix to device type, e.g. UCC28083DR (2500 devices
per reel) or UCC38083PWR (2000 devices per reel).
PW PACKAGE
(TOP VIEW)
D OR P PACKAGE
(TOP VIEW)
CTRL
ISET
CS
RT
2
1
8
2
7
3
6
4
5
VDD
OUTA
OUTB
GND
OUTA
VDD
CTRL
ISET
www.ti.com
1
2
3
4
8
7
6
5
OUTB
GND
RT
CS
SLUS488E − SEPTEMBER 2002 − REVISED JULY 2009
absolute maximum ratings over operating free-air temperature (unless otherwise noted)†
Supply voltage, VDD (IDD < 10 mA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 V
Supply current, IDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA
Sink current (peak):
OUTA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0 A
OUTB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0 A
Source current (peak): OUTA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 A
OUTB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 A
Analog inputs:
CTRL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to VDD +0.3 V
CS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to VDD +0.3 V, not to exceed 6 V
RSET (minimum) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >5 kΩ
RT (−100 µA < IRT < 100 µA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 2.0 V
Power dissipation at TA = 25°C (P package) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 W
Power dissipation at TA = 25°C (D package) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 650 mW
Power dissipation at TA = 25°C (PW package) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400 mW
Junction operating temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55°C to 150°C
Storage temperature, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
Lead temperature (soldering 10 seconds) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltages are with respect to GND.
Currents are positive into, and negative out of the specified terminal.
electrical characteristics over recommended operating virtual junction temperature range,
VDD = 10 V (See Note 1),1-µF capacitor from VDD to GND, RT = 165 kΩ, RF = 1 kΩ, CF = 220 pF,
RSET = 50 kΩ, TA = −40°C to 85°C for UCC2808x, TA = 0°C to 70°C for UCC3808x, TA = TJ
(unless otherwise noted)
overall
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
Start-up current
VDD < UVLO start threshold voltage
120
200
µA
Supply current
CTRL = 0 V,
See Note 1
1.5
2.5
mA
MIN
TYP
MAX
CS = 0 V,
undervoltage lockout
PARAMETER
TEST CONDITIONS
UCC38083/5
Start threshold voltage
Minimum operating voltage
after start
Hysteresis voltage
11.5
12.5
13.5
UCC38084/6
See Note 1
4.1
4.3
4.5
UCC38083/5
7.6
8.3
9.0
UCC38084/6
3.9
4.1
4.3
UCC38083/5
3.5
4.2
5.1
UCC38084/6
0.1
0.2
0.3
UNITS
V
oscillator
MIN
TYP
MAX
UNITS
Frequency
PARAMETER
2 x f(OUTA)
TEST CONDITIONS
180
200
220
kHz
Voltage amplitude
See Note 2
1.4
Oscillator fall time (dead time)
RT pin voltage
1.2
www.ti.com
1.5
1.6
V
110
220
ns
1.5
1.6
V
3
SLUS488E − SEPTEMBER 2002 − REVISED JULY 2009
electrical characteristics over recommended operating virtual junction temperature range,
VDD = 10 V (See Note 1),1-µF capacitor from VDD to GND, RT = 165 kΩ, RF = 1 kΩ, CF = 220 pF,
RSET = 50 kΩ, TA = −40°C to 85°C for UCC2808x, TA = 0°C to 70°C for UCC3808x, TA = TJ
(unless otherwise noted)
current sense
PARAMETER
TEST CONDITIONS
Gain
See Note 3
Maximum input signal voltage
CTRL = 5 V,
See Note 4
CS to output delay time
CTRL = 3.5 V,
0 mV ≤ CS ≤ 600 mV
CS = 0.5 V,
See Note 5
RT = 2.0 V,
Source current
MIN
TYP
MAX
1.9
2.2
2.5
0.47
0.52
0.57
V
100
200
ns
−200
Sink current
Overcurrent threshold voltage
CTRL to CS offset voltage
UNITS
V/V
nA
3
7
12
mA
0.70
0.75
0.80
V
CS = 0 V, 25°C
0.55
0.70
0.90
V
CS = 0 V
0.37
0.70
1.10
V
MIN
TYP
MAX
UNITS
48%
49%
50%
pulse width modulation
PARAMETER
TEST CONDITIONS
Maximum duty cycle
Measured at OUTA or OUTB, See Note 7
Minimum duty cycle
CTRL = 0 V
0%
output
PARAMETER
TEST CONDITIONS
Low-level output voltage (OUTA or OUTB)
MIN
TYP
MAX
0.5
1.0
0.5
1.0
High-level output voltage (OUTA or OUTB)
IOUT = 100 mA
IOUT = −50 mA,
Rise time
CLOAD = 1 nF
25
60
Fall time
CLOAD = 1 nF
25
60
MIN
TYP
MAX
(VDD − VOUT), See Note 6
UNITS
V
ns
soft-start
PARAMETER
TEST CONDITIONS
UNITS
OUTA/OUTB soft-start interval time,
UCC38083/4
CTRL = 1.8 V,
CS = 0 V,
Duty cycle from 0 to full, See Note 8
1.3
3.5
8.5
ms
OUTA/OUTB soft-start interval time,
UCC38085/6
CTRL = 1.8 V,
CS = 0 V,
Duty cycle from 0 to full, See Note 8
30
75
110
µs
TEST CONDITIONS
MIN
TYP
MAX
UNITS
IRAMP, peak
ISET, peak = 30 µA, Full duty cycle
NOTE 1: For UCCx8083/5, set VDD above the start threshold before setting to 10 V.
NOTE 2: Measured at ISET pin.
DV CTRL
NOTE 3: Gain is defined by A +
, 0 ≤ VCS ≤ 0.4 V.
DV
125
150
175
µA
slope compensation
PARAMETER
CS
NOTE 4:
NOTE 5:
NOTE 6:
NOTE 7:
NOTE 8:
4
Measured at trip point of latch with CS ramped from 0.4 V to 0.6 V.
This internal current sink on the CS pin is designed to discharge and external filter capacitor. It is not intended to be a dc sink path.
Not 100% production tested. Ensured by design and also by the rise time test.
For devices in PW package, parameter tested at wafer probe.
Ensured by design.
www.ti.com
SLUS488E − SEPTEMBER 2002 − REVISED JULY 2009
functional block diagram
Soft Start and Fault Latch
CTRL
1
S
Iss
Bias/UVLO
VREF
Q
0.5V
Slope Circuit
ISLOPE
8
R
Vdd−1
VDD
S
CT
+
R
Css
ISET
Q
I SLOPE =
5 x I SET
2
CS Circuitry
0.75V
PWM Comparator/Latch
Output Driver
7
OUTA
80 kΩ
S
60 kΩ
0.5V
CS
Q
Q
T
R
0.3 V
Q
3
6
OUTB
Oscillator
1.5V
1.5V
S
Q
I CT
R
RT
4
5
CT
0.2V
GND
UDG−01081
Terminal Functions
TERMINAL
NAME
PACKAGE
I/O
DESCRIPTION
D OR P
CS
3
I
The current-sense input to the PWM comparator, the cycle-by-cycle peak current comparator, and the
overcurrent comparator. The overcurrent comparator is only intended for fault sensing. Exceeding the
overcurrent threshold causes a soft-start cycle. An internal MOSFET discharges the current-sense filter
capacitor to improve dynamic performance of the power converter.
CTRL
1
I
Error voltage input to PWM comparator.
GND
5
−
Reference ground and power ground for all functions. Due to high currents, and high-frequency operation
of the IC, a low-impedance circuit board ground plane is highly recommended.
Current selection for slope compensation.
ISET
2
I
OUTA
7
O
OUTB
6
O
RT
4
I
Programs the oscillator.
VDD
8
I
Power input connection.
Alternating high-current output stages.
www.ti.com
5
SLUS488E − SEPTEMBER 2002 − REVISED JULY 2009
detailed pin descriptions
CTRL: The error voltage is typically generated by a secondary-side error amplifier and transmitted to the
primary-side referenced UCC3808x by means of an opto-coupler. CTRL has an internal divider ratio of 0.45 to
maintain a usable range with the minimum VDD of 4.1 V. The UCC38083/UCC38084 family features a built-in
full-cycle soft start while the UCC38085/6 does not.
For the UCC38083/4, soft-start is implemented as a clamp at the input to the PWM comparator. This causes
the output pulses to start near 0% duty cycle and increase until the clamp exceeds the CTRL voltage.
ISET: Program the slope compensation current ramp by connecting a resistor, RSET, from ISET to ground. The
voltage of the ISET pin tracks the 1.5-V internal oscillator ramp, as shown in Figure 1.
VCS
VDD
10 k
I RAMP, peak = 5 x ISET, peak
IRAMP
UCC38083
RF
1 k
I RAMP
1 CTRL VDD 8
2 ISET OUTA 7
3 CS
OUTB 6
4 RT
GND 5
ISET
1 F
OUTA
220 F
RT
165 k
OUTB
Figure 1. Full Duty Cycle Output
The compensating current source, ISLOPE, at the CS pin is proportional to the ISET current, according to the
relation:
I
SLOPE
+5
I
SET
(1)
The ramping current due to ISLOPE develops a voltage across the effective filter impedance that is normally
connected from the current sense resistor to the CS input. In order to program a desired compensating slope
with a specific peak compensating ramp voltage at the CS pin, use the RSET value in the following equation:
RSET + V
Where V
OSC(peak)
OSC(peak)
5 RF
ǒRAMP VOLTAGE
Ǔ
HEIGHT
(2)
+ 1.5 V
Notice that the PWM Latch drives an internal MOSFET that will discharge an external filtering capacitor on the
CS pin. Thus, ISLOPE will appear to terminate when the PWM comparator or the cycle-by-cycle current limit
comparator sets the PWM latch. The actual compensating slope is not affected by premature termination of the
switching cycle.
6
www.ti.com
SLUS488E − SEPTEMBER 2002 − REVISED JULY 2009
detailed pin descriptions (continued)
OUTA and OUTB: Alternating high-current output stages. Both stages are capable of driving the gate of a power
MOSFET. Each stage is capable of 500-mA peak-source current, and 1-A peak-sink current.
The output stages switch at half the oscillator frequency, in a push-pull configuration. When the voltage on the
internal oscillator capacitor is rising, one of the two outputs is high, but during fall time, both outputs are off. This
dead time between the two outputs, along with a slower output rise time than fall time, ensures that the two
outputs cannot be on at the same time. This dead time is typically 110 ns.
The high-current output drivers consist of MOSFET output devices, which switch from VDD to GND. Each output
stage also provides a very low impedance to overshoot and undershoot. This means that in many cases,
external Schottky clamp diodes are not required.
RT: The oscillator programming pin. The oscillator features an internal timing capacitor. An external resistor,
RT, sets a current from the RT pin to ground. Due to variations in the internal CT, nominal VRT of 1.5 V can vary
from 1.2 V to 1.6 V
Selecting RT as shown programs the oscillator frequency:
RT +
1
28.7
ǒ
1 * 2.0
10 −12 f OSC
Ǔ
10 −7
(3)
where fOSC is in Hz, resistance in Ω. The recommended range of timing resistors is between 25 kΩ and 698 kΩ.
For best performance, keep the timing resistor lead from the RT pin to GND (pin 5) as short as possible.
1.5 V
I
1.5 V
I
RT
S
Q
CT
R
OSCILLATOR
4
0.2 V
CT
R
OUTPUT
T
Approximate Frequency +
28.7
10 −12
1
R T ) ǒ2.0
10 −7Ǔ
UDG−01083
Figure 2. Block Diagram for Oscillator
VDD: The power input connection for this device. Although quiescent VDD current is very low, total supply
current may be higher, depending on OUTA and OUTB current, and the programmed oscillator frequency. Total
VDD current is the sum of quiescent VDD current and the average OUT current. Knowing the operating
frequency and the MOSFET gate charge (QG), average OUT current can be calculated from:
I
OUT
+Q
G
f OSC
(4)
where f is the oscillator frequency.
To prevent noise problems, bypass VDD to GND with a ceramic capacitor as close to the chip as possible along
with an electrolytic capacitor. A 1-µF decoupling capacitor is recommended.
www.ti.com
7
SLUS488E − SEPTEMBER 2002 − REVISED JULY 2009
APPLICATION INFORMATION
The following application circuit shows an isolated 12-VIN to 2.5 VOUT push-pull converter with scalable output
power (20 W to 200 W). Note that the pinout shown is for SOIC-8 and PDIP-8 packages.
typical application
V O= 2.2 V TO 3.3 V
ADJUSTABLE
VIN = 12 V
+/−20%V
SR
DRIVE
1 µF
8
VDD
4.7Ω
7 OUTA
RT 4
UCC3808x
4.7Ω
6
6 OUTB
RF 1 kΩ
RS
3 CS
CTRL 1
GND
ISET
5
2
CF
220 pF
5
165
kΩ
4
1
2
3
TL431
RSET
UDG−01084
8
www.ti.com
SLUS488E − SEPTEMBER 2002 − REVISED JULY 2009
APPLICATION INFORMATION
operational waveforms
Figure 3 illustrates how the voltage ramp is effectively added to the voltage across the current sense element
VCS, to implement slope compensation.
OUTA
OUTB
VRS
ADDED
RAMP
VOLTAGE
VCS, Pin 3
UDG−01085
Figure 3. Typical Slope Compensation Waveforms at 80% Duty Cycle
In Figure 3, OUTA and OUTB are shown at a duty cycle of 80%, with the associated voltage VRS across the
current sense resistor of the primary push-pull power MOSFETs. The current flowing out of CS generates the
ramp voltage across the filter resistor RF that is positioned between the power current sense resistor and the
CS pin. This voltage is effectively added to VRS to provide slope compensation at VCS, pin 3. A capacitor CF
is also recommended to filter the waveform at CS.
www.ti.com
9
SLUS488E − SEPTEMBER 2002 − REVISED JULY 2009
layout considerations
To prevent noise problems, bypass VDD to GND with a ceramic capacitor as close to the chip as possible along
with an electrolytic capacitor. A 1-µF decoupling capacitor is recommended.
Use a local ground plane near the small signal pins (CTRL, ISET, CS and RT) of the IC for shielding. Connect
the local ground plane to the GND pin with a single trace. Do not extend the local ground plane under the power
pins (VDD, OUTA, OUTB and GND). Instead, use signal return traces to the GND pin for ground returns on the
side of the integrated circuit with the power pins.
For best performance, keep the timing resistor lead from RT pin (pin 4) to GND (pin 5) as short as possible.
special layout considerations for the TSSOP package
Due to the different pinout and smaller lead pitch of the TSSOP package, special attention must be paid to
minimize noise problems. The pinout is different because the device had to be rotated 90° to fit into the smaller
TSSOP package.
For example, the two output pins are now on opposite sides of the package. The traces should not run under
the package together as they will couple switching noise into analog pins.
Another common problem is when RT and OUTB (pins 6 and 8) are routed together for some distance even
though they are not immediate side by side pins. Because of this, when OUTB rises, a voltage spike of upto
400 mV can couple into the RT. This spike causes the internal charge current into CT to be turned off
momentarily resulting in lower duty cycle. It is also important that note that the RT pin voltage cannot be
stabilized with a capacitor. The RT pin is just a dc voltage to program the internal CT. Instead, keep the OUTB
and RT runs short and far from each other and follow the printed wiring board layout suggestions above to fix
the problem.
reference design
A reference design is discussed in 50-W Push-Pull Converter Reference Design Using the UCC38083, TI
Literature Number SLUU135. This design controls a push-pull synchronous rectified topology with input range
of 18 V to 35 V (24 nominal) and 3.3-V output at 15 A. The schematic is shown in Figure 5 and the board layout
for the reference design is shown in Figure 4. Refer to the document for further details.
Figure 4. Reference Design Layout
10
www.ti.com
www.ti.com
VCC
See Note 2
2OUT
1OUT
REG_OUT
2IN
1IN
GND
REG_IN
3
1
4
2
Note 1. C28, R25, and D12 accelerate the control to the secondary side feedback at start-up and prevent output voltage overshoot.
Note 2. Components used for the UCC38085 only.
+
5
7
8
6
+
+
SLUS488E − SEPTEMBER 2002 − REVISED JULY 2009
APPLICATION INFORMATION
Figure 5. Reference Design Schematic
11
SLUS488E − SEPTEMBER 2002 − REVISED JULY 2009
TYPICAL CHARACTERISTICS
OSCILLATOR FREQUENCY
vs
TEMPERATURE
OSCILLATOR FREQUENCY
vs
TIMING RESISTANCE
220
1200
215
T = 85°C
VDD = 15 V
1000
RT = 165 kΩ″
RF= 1 kΩ
CF = 220 kΩ
RSET = 50 kΩ
Frequency − kHz
800
Frequency − kHz
210
T = 25°C
VDD = 10 V
600
400
205
200
195
190
200
T = 40°C
VDD = 6 V
185
180
0
10
100
−50
1000
0
25
50
75
100
125
Temperature − °C
RT − Timing Resistance − kΩ
Figure 6
Figure 7
IDD
vs
OSCILLATOR FREQUENCY, (NO LOAD)
IDD
vs
OSCILLATOR FREQUENCY, 1 nF LOAD
25
12
VDD = 14 V
10
20
8
IDD − mA
15
IDD − mA
−25
VDD = 10 V
6
10
VDD = 14 V
VDD = 10 V
VDD = 6 V
4
VDD = 6 V
5
2
0
0
10
12
100
1000
10
100
Frequency − kHz
Frequency − kHz
Figure 8
Figure 9
www.ti.com
1000
SLUS488E − SEPTEMBER 2002 − REVISED JULY 2009
TYPICAL CHARACTERISTICS
DEAD TIME
vs
TIMING RESISTANCE OVER VDD
DEAD TIME
vs
TEMPERATURE
200
160
180
160
VDD = 6 V*
T = 85°C
T = 25°C
RT = 165 kΩ″
RF= 1 kΩ
CF = 220 kΩ
RSET = 50 kΩ
140
120
Dead Time − ns
VDD = 10 V
Dead Time − ns
VDD = 6 V*
140
120
100
VDD = 14 V
80
60
VDD = 14 V
T = −40°C
100
80
60
40
40
20
20
* UCCx8084/6, only
0
0
10
1000
100
−50
−25
0
25
Figure 10
100
125
Figure 11
CONTROL TO CS OFFSET
vs
TEMPERATURE
RAMP HEIGHT
vs
VDD
0.6
2.0
TA = 25°C
1.8
(OC Clamped)
RSET = 10 kΩ
0.5
1.6
VCS = 0.40 V
1.4
RSET = 18 kΩ
0.4
VPK(cs) − V
VCTRL − Control Voltage − V
75
50
Temperature − °C
RT − Timing Resistance − kΩ
1.2
1.0
0.8
0.3
0.2
0.6
RSET = 50 kΩ
0.4
VCS = 0 V
0.1
RSET = 100 kΩ
0.2
0
0.0
−50
−25
0
25
50
75
100
125
Temperature − °C
0
10
5
15
VDD − Volts
Figure 13
Figure 12
www.ti.com
13
SLUS488E − SEPTEMBER 2002 − REVISED JULY 2009
TYPICAL CHARACTERISTICS
RAMP HEIGHT
vs
RT
RAMP HEIGHT
vs
TEMPERATURE
0.7
0.6
TA = 25°C
RSET = 10 kΩ
0.6
0.5
(OC Clamped)
VPK(cs) − V
0.4
VPK(cs) − V
RSET = 10 kΩ
0.5
(OC Clamped)
RSET = 18 kΩ
0.3
0.4
0.3
0.2
0.2
RSET = 50 kΩ
RSET = 18 kΩ
RSET = 50 kΩ
0.1
0.1
RSET = 100 kΩ
RSET = 100 kΩ
0
0.0
100
10
1000
−50
−25
0
25
50
75
100
125
Temperature − °C
RT − kΩ
Figure 14
Figure 15
SOFT START
vs
TEMPERATURE
SOFT START
vs
TEMPERATURE
6
100
UCCx8085 AND UCCx8086
UCCx8083 AND UCCx8084
95
90
Soft Start Internal − µs
Soft Start Internal − ms
5
4
3
2
85
80
75
70
65
60
1
55
0
−50
50
−25
0
25
50
75
100
125
Temperature −°C
−25
0
25
50
Temperature − °C
Figure 16
14
−50
Figure 17
www.ti.com
75
100
125
SLUS488E − SEPTEMBER 2002 − REVISED JULY 2009
TYPICAL CHARACTERISTICS
CS TO OUTX DELAY TIME
vs
TEMPERATURE
150
140
CS Prop Delay − ns
130
120
110
100
90
80
70
60
50
−50
−25
0
25
50
75
100
125
Temperature − °C
Figure 18
RELATED PRODUCTS
UCC3808, 8-Pin Low Power Current Mode Push-Pull PWM, (SLUS168)
UCC3808A, 8-Pin Low-Power Current-Mode Push-Pull PWM, (SLUS456)
UCC3806, Low Power, Dual Output, Current Mode PWM Controller, (SLUS272)
Table 1. 8-Pin Push-Pull PWM Controller Family Feature Comparison
UVLO On
UVLO Off
CS
Discharge FET
Error
Amplifier
Programmable
Slope
Compensation
Internal
Softstart
12.5 V
8.3 V
Yes
No
Yes
Yes
UCC38084
4.3 V
4.1 V
Yes
No
Yes
Yes
UCC38085
12.5 V
8.3 V
Yes
No
Yes
No
UCC38086
4.3 V
4.1 V
Yes
No
Yes
No
UCC3808A−1
12.5 V
8.3 V
Yes
Yes
No
Yes
UCC3808A−2
4.3 V
4.1 V
Yes
Yes
No
Yes
UCC3808−1
12.5 V
8.3 V
No
Yes
No
Yes
UCC3808−2
4.3 V
4.1 V
No
Yes
No
Yes
Part Number
UCC38083
www.ti.com
15
PACKAGE OPTION ADDENDUM
www.ti.com
30-Jul-2011
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
UCC28083D
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC28083DG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC28083DR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC28083DRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC28083P
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU N / A for Pkg Type
UCC28083PG4
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU N / A for Pkg Type
UCC28083PW
ACTIVE
TSSOP
PW
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
UCC28083PWG4
ACTIVE
TSSOP
PW
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
UCC28084D
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC28084DG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC28084DR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC28084DRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC28084P
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU N / A for Pkg Type
UCC28084PG4
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU N / A for Pkg Type
UCC28084PW
ACTIVE
TSSOP
PW
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
UCC28084PWG4
ACTIVE
TSSOP
PW
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
UCC28084PWR
ACTIVE
TSSOP
PW
8
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Addendum-Page 1
Samples
(Requires Login)
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
30-Jul-2011
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
UCC28084PWRG4
ACTIVE
TSSOP
PW
8
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
UCC28085D
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC28085DG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC28085DR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC28085DRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC28085P
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU N / A for Pkg Type
UCC28085PG4
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU N / A for Pkg Type
UCC28085PW
ACTIVE
TSSOP
PW
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
UCC28085PWG4
ACTIVE
TSSOP
PW
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
UCC28086D
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC28086DG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC28086DR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC28086DRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC28086P
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU N / A for Pkg Type
UCC28086PG4
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU N / A for Pkg Type
UCC28086PW
ACTIVE
TSSOP
PW
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
UCC28086PWG4
ACTIVE
TSSOP
PW
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
UCC28086PWR
ACTIVE
TSSOP
PW
8
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Addendum-Page 2
Samples
(Requires Login)
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
30-Jul-2011
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
UCC28086PWRG4
ACTIVE
TSSOP
PW
8
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
UCC38083D
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC38083DG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC38083DR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC38083DRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC38083P
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU N / A for Pkg Type
UCC38083PG4
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU N / A for Pkg Type
UCC38084D
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC38084DG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC38084DR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC38084DRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC38084P
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU N / A for Pkg Type
UCC38084PG4
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU N / A for Pkg Type
UCC38084PW
ACTIVE
TSSOP
PW
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
UCC38084PWG4
ACTIVE
TSSOP
PW
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
UCC38084PWR
ACTIVE
TSSOP
PW
8
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
UCC38084PWRG4
ACTIVE
TSSOP
PW
8
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
UCC38085D
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Addendum-Page 3
Samples
(Requires Login)
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
30-Jul-2011
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
UCC38085DG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC38085P
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU N / A for Pkg Type
UCC38085PG4
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU N / A for Pkg Type
UCC38086D
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC38086DG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC38086DR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC38086DRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
UCC38086P
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU N / A for Pkg Type
UCC38086PG4
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU N / A for Pkg Type
(3)
Samples
(Requires Login)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Addendum-Page 4
PACKAGE OPTION ADDENDUM
www.ti.com
30-Jul-2011
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 5
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
UCC28083DR
Package Package Pins
Type Drawing
SOIC
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
UCC28084DR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
UCC28084PWR
TSSOP
PW
8
2000
330.0
12.4
7.0
3.6
1.6
8.0
12.0
Q1
UCC28085DR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
UCC28086DR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
UCC28086PWR
TSSOP
PW
8
2000
330.0
12.4
7.0
3.6
1.6
8.0
12.0
Q1
UCC38083DR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
UCC38084DR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
UCC38084PWR
TSSOP
PW
8
2000
330.0
12.4
7.0
3.6
1.6
8.0
12.0
Q1
UCC38086DR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
UCC28083DR
SOIC
D
8
2500
340.5
338.1
20.6
UCC28084DR
SOIC
D
8
2500
340.5
338.1
20.6
UCC28084PWR
TSSOP
PW
8
2000
367.0
367.0
35.0
UCC28085DR
SOIC
D
8
2500
340.5
338.1
20.6
UCC28086DR
SOIC
D
8
2500
340.5
338.1
20.6
UCC28086PWR
TSSOP
PW
8
2000
367.0
367.0
35.0
UCC38083DR
SOIC
D
8
2500
340.5
338.1
20.6
UCC38084DR
SOIC
D
8
2500
340.5
338.1
20.6
UCC38084PWR
TSSOP
PW
8
2000
367.0
367.0
35.0
UCC38086DR
SOIC
D
8
2500
340.5
338.1
20.6
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated