UFA_MP-6W & UFB_MP-6W Series 6W, WIDE INPUT, ISOLATED & REGULATED DUAL & SINGLE OUTPUT, DC-DC CONVERTER multi-country patent protection FEATURES RoHS PRODUCT PROGRAM Efficiency up to 86% Wide (4:1) Input Range 1.5KVDC Input/Output Isolation Continuous Short Circuit Protection Operating Temperature: -40°C to +85°C Internal SMD construction Metal Shielding Package No Heat Sink Required Industry Standard Pinout MTBF>1,000,000 hours RoHS Compliance APPLICATIONS The UFA_MP-6W & UFB_MP-6W Series are specially designed for applications where a wide range input voltage power supplies are isolated Input Part Number Output Voltage (VDC) Nominal Range Max** Efficiency (%, Typ) Current (mA) Voltage (VDC) Max Min UFA2405MP-6W ±5 ±600 ±60 80 UFA 2412MP-6W ±12 ±250 ±25 80 UFA 2415MP-6W ±15 ±200 ±20 82 UFA 2424MP-6W ±24 ±125 ±13 85 3.3 1500 150 78 UFB2405MP-6W 5 1200 120 80 UFB2412MP-6W 12 500 50 82 UFB2415MP-6W 15 400 40 82 UFB2403MP-6W 24 9-36 40 UFB2424MP-6W 24 250 25 83 UFA4805MP-6W * ±5 ±600 ±60 80 UFA4812MP-6W ±12 ±250 ±25 82 UFA4815MP-6W ±15 ±200 ±20 84 UFA4824MP-6W ±24 ±125 ±13 85 3.3 1500 150 76 48 18-75 80 from the input power supply in a distributed UFB4803MP-6W * power supply system on a circuit board. UFB4805MP-6W 5 1200 120 80 UFB4812MP-6W 12 500 50 84 UFB4815MP-6W 15 400 40 85 UFB4824MP-6W 24 250 25 86 These products apply to: 1) Where the voltage of the input power supply is wide range (voltage range≤4:1); 2) Where isolation is necessary between input and output(Isolation Voltage≤1500VDC); 3) Where the regulation of the output voltage and the output ripple noise are demanded. * Designing. * * Input voltage can’t exceed this value, or will cause the permanent damage. Note: The load shouldn't be less than 10%, otherwise ripple will increase dramatically. Operation under 10% load will not damage the converter; However, they may not meet all specification listed. MODEL SELECTION UFA2405MP-6W OUTPUT SPECIFICATIONS Rated Power Package Styl e Output Voltage Input Voltage Product Ser ies Item Test Conditions Output Power See below products program MORNSUN reserves the copyright Typ Max Units 6 W Line Regulation(at full load) Input voltage from low to high ±0.2 ±0.5 Load Regulation From 10% To 100% load ±0.5 ±2* Positive Voltage Accuracy Refer to recommended circuit ±1 ±3 ±3 ±5 Negative Voltage Accuracy Refer to recommended circuit MORNSUN Science& Technology co.,Ltd. Address: 2th floor 6th building, Huangzhou Industrial District, Guangzhou, China Tel: 86-20-38601850 Fax: 86-20-38601272 Http://www.mornsun-power.com Min Temperature Drift(Vout) Refer to recommended circuit 0.02 Ripple** 20MHz bandwidth 30 50 Noise** 20MHz bandwidth 100 300 Switching Frequency 100% load, nominal Input voltage 300 % %/°C mVp-p KHz * Dual output models unbalanced load: ±5%. **Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of Power Converter section, application notes. Specifications subject to change without notice. UFA_MP-6W & UFB_MP-6W A/2-2008 Page 1 of 2 COMMON SPECIFICATION Item APPLICATION NOTE Test Conditions Typ Min Max Units 95 % Storage humidity Operating temperature -40 85 Storage temperature -55 125 Temp. rise at full load have been tested according to the following °C 40 recommended 1.5mm from case for 10 seconds 300 Isolation voltage Tested for 1 minute and 1mA max 1500 VDC Isolation resistance Test at 500VDC 1000 MΩ Copper, Nickel Plated MTBF 1000 Weight K hours 17 before leaving +Vout Ci n Continuous, automatic recovery Case material circuit Dual Output Vin Free air convection Short circuit protection testing factory. This series should be tested under load. Never be tested under no load (see Figure 1). Lead temperature Cooling Recommended Circuit All the UFA_MP-6W & UFB_MP-6W Series g Note: 1. All specifications measured at TA=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified. 2. See below recommended circuits for more details. DC DC GND 0V -Vout Single Output Vin Cin +Vout DC DC 0V GND (Figure 1) If you want to further decrease the output ripple, you can increase capacitance properly or choose TYPICAL CHARECTERISTICS capacitors with low ESR. However, the capacitance should not be too high.(Table 1). Temperature Derating Graph Vin (VDC) 24 48 --- External Capacitor Table(Table 1) Single Dual Cin Cout Cout Vout Vout (uF) (uF) (uF) (VDC) (VDC) 100 5 100 ±5 100 100 12 100 ±12 47 -15 47 ±15 47 -24 47 ±24 22 Operating Temp.( C ) OUTLINE DIMENSIONS & PIN CONNECTIONS Fi rst Angle Pr ojection RECO MMENDED FOOTPRINT 20.00 (0.787) 32.00 (1.2 60) To p view, gr id :2 .54 m m (0 .1in ch) , dia m ete r: 1.0 0m m (0 .0 39 inch ) Dual Outpu t 2 3 9 11 B ot tom V iew 2 322 2 3 22 16 14 2 3 9 11 16 14 16 14 2.54 (0.100) Single O utput 4.10 S id e V ie w 0.50 (0.020) 10.00 (0.394) 2 3 22 11 FO OTP RINT DETAIL S Single Dual Pin Note: Unit:mm(inch) Pin diameter:0 .50mm(0.020inch) Pin diameter tolera nces: 0.05mm( 0.002inch) Genera l tolerances: 0.25mm( 0.010inch) MORNSUN reserves the copyright 2 3 2,3 9 11 14 GND NP GND COM NC +Vo -Vo +Vo COM 16 0V 22,2 3 Vin NC:No Connection Vin Specifications subject to change without notice. UFA_MP-6W & UFB_MP-6W A/2-2008 Page 2 of 2