ALUMINUM ELECTROLYTIC CAPACITORS ZS 4.5mmL Chip Type series Chip type with 4.5mm height. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC). ZT WX Smaller ZS High Te m p e rature Bi-polarized ZP Smaller ZR Specifications Item Performance Characteristics Category Temperature Range – 40 ~ + 85°C Rated Voltage Range 4 ~ 50V Rated Capacitance Range 0.1 ~ 220µF Capacitance Tolerance + – 20% at 120Hz, 20°C After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) ,whichever is greater. Leakage Current Measurement frequency : 120Hz, Temperature : 20°C tan δ Rated voltage (V) tan δ (MAX.) 4 0.50 6.3 0.30 10 0.24 16 0.19 25 0.16 35 0.14 50 0.14 Measurement frequency : 120Hz 4 7 15 Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio ZT / Z20 (MAX.) Z– 40°C / Z+20°C Stability at Low Temperature 6.3 4 8 16 2 4 35 2 3 50 2 3 Within + – 20% of initial value 200% or less of initial specified value Initial specified value or less After storing the capacitors under no load at 85°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250°C Capacitance change Within + – 10% of initial value for 30 seconds. After removing from the hot plate and restored tan δ Initial specified value or less at room temperature,they meet the characteristic requirements Initial specified value or less Leakage current listed at right. Shelf Life Resistance to soldering heat Black print on the case top. Marking Type numbering system (Example : 16V 10µF) Chip Type 1 4.5 Voltage mark for 6.3V is C+ – 0.2 3 4 5 6 7 8 9 10 11 12 13 14 Taping code E B+– 0.2 X2 10 16V φD+– 0.5 Voltage 2 U Z S 1 C 1 0 0 MC L 1 GB A+– 0.2 A + – 0.2 Plastic platform 0.3 MAX. 0.5 MAX. Positive Capacitance Lot No. 25 2 4 Capacitance change tan δ Leakage current After 2000 hours' application of rated voltage at 85°C,capacitors meet the characteristics requirements listed at right. Endurance 10 3 8 φD A B C E 4 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 (mm) 6.3 2.4 6.6 6.6 2.2 Configuration Capacitance tolerance (+ – 20%) Rated Capacitance (10µF) Rated voltage (16V) +0.1 –0.2 Series name Negative 0.5 ~ 0.8 6V . Type Dimensions 4 0G V Cap. (µF) 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 220 Code 0R1 R22 R33 R47 010 2R2 3R3 4R7 100 220 330 470 101 221 4 4 5 6.3 6.3 0J 28 33 56 96 4 5 5 6.3 10 1A 28 37 45 70 5 5 6.3 16 1C 33 41 52 4 5 6.3 6.3 25 1E 23 37 49 58 4 5 6.3 6.3 35 1V 16 27 42 52 4 5 6.3 50 1H 18 29 46 4 4 4 4 4 4 4 5 6.3 Case size φ D (mm) 1.0 2.0 2.8 4.0 8.4 13 17 20 33 Rated ripple Rated Ripple (mArms) at 85°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz~ 1.50 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please select UR(p.70), UG(p.75) series if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. CAT.8100V