ALUMINUM ELECTROLYTIC CAPACITORS CJ Chip Type, High Reliability. Low temperature ESR specification. series Chip type, high temperature range, for +125°C use. Added ESR specification after the test at – 40°C (φ6.3 sizes provide only for the first stage. ) Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC). Added ESR specification at – 40°C CJ UB Specifications Item Performance Characteristics Category Temperature Range – 40 ~ +125°C Rated Voltage Range 10 ~ 50V Rated Capacitance Range 10 ~ 470µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 1 minute's application of rated voltage, leakage current is not more than 0.03CV or 4(µA) , whichever is greater. Measurement frequency : 120Hz, Temperature : 20°C tan δ 10 0.32 Rated voltage (V) tan δ (MAX.) 16 0.24 25 0.21 35 0.18 50 0.18 Measurement frequency : 120Hz Rated voltage (V) Stability at Low Temperature Impedance ratio ZT / Z20 (MAX.) Z– 40°C / Z+20°C 10 16 25 35 50 12 8 6 4 4 Capacitance change tan δ Leakage current After 2000 hours' application of rated voltage at 125°C, capacitors meet the characteristic requirements listed at right. Endurance Within ±30% of initial value 300% or less of intial specified value Initial specified value or less After storing the capacitors under no load at 125°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250°C Capacitance change Within ±10% of initial value for 30 seconds. After removing from the hot plate and restored tan δ Initial specified value or less at room temperature, they meet the characteristic requirements Leakage current Initial specified value or less listed at right. Shelf Life Resistance to soldering heat Black print on the case top. Chip Type f Lot No. f A2 100V CJ D± 0.5 Series Capacitance Negative H Plastic platform 0.3MAX. (φ8 × 10, φ10 × 10) Voltage( V : 35V ) Trade mark E L±0.3 C±0.2 Positive 0.5MAX. Capacitance B±0.2 Lot No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 L±0.5 UC J 1 A 1 0 1 MCL 1GS A±0.2 A±0.2 D± 0.5 A2 47C CJ Series C±0.2 0.5MAX. Plastic platform 0.3MAX. B±0.2 Voltage( C : 16V ) Type numbering system (Example : 10V 100µF) Positive E (φ6.3 × 8.7) A B C E L H Negative H D L 6.3 ´ 8.7 f ´ A±0.2 A±0.2 Marking (mm) Taping code Configuration Capacitance tolerance (±20%) Rated Capacitance (100mF) Rated voltage (10V) Series name Type 8 ´ 10 10 ´ 10 2.4 2.9 3.2 6.6 8.3 10.3 6.6 8.3 10.3 2.2 3.1 4.5 8.7 10 10 0.5 ~ 0.8 0.8 ~ 1.1 0.8 ~ 1.1 Dimensions Cap.(µF) 10 22 33 47 100 220 330 470 10 1A V Code 100 220 330 470 101 221 331 471 6.3 × 8.7 8 × 10 10 × 10 10 × 10 14 2.0 1.5 1.5 16 1C 95 6.0 250 4.5 400 4.5 400 6.3 × 8.7 8 × 10 10 × 10 10 × 10 14 2.0 1.5 1.5 25 1E 95 6.0 250 4.5 400 4.5 400 6.3 × 8.7 6.3 × 8.7 6.3 × 8.7 8 × 10 10 × 10 10 × 10 14 14 14 2.0 1.5 1.5 6.3 × 8.7 95 6.3 × 8.7 95 6.3 × 8.7 95 6.3 × 8.7 6.0 250 10 × 10 4.5 400 10 × 10 4.5 400 35 1V 14 14 14 14 1.5 1.5 95 6.3 × 8.7 95 6.3 × 8.7 8 × 10 95 95 10 × 10 4.5 400 10 × 10 4.5 400 Case size φD× L (mm) 50 1H 14 14 2.0 1.5 1.5 95 95 6.0 200 4.5 330 4.5 330 after Initial torture test ESR Rated ripple Max. ESR (Ω) at -40°C 100kHz, Rated Ripple (mArms) at 125°C 100kHz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.35 120 Hz 0.50 300 Hz 0.64 1 kHz 0.83 10 kHz~ 1.00 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please refer to page 3 for the minimum order quantity. CAT.8100V-2