ALUMINUM ELECTROLYTIC CAPACITORS UP 6mmL Chip Type, Bi-Polarized series Chip type, bi-polarized withstanding high temperature range up to +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU). UN Extended range UP High Temperature WP Specifications Item Performance Characteristics Category Temperature Range –55 to +105°C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 0.1 to 47µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.05 CV or 10 (µA), whichever is greater. Measurement frequency : 120Hz at 20°C 6.3 0.24 Rated voltage (V) tan δ (MAX.) Tangent of loss angle (tan δ) 10 0.20 16 0.17 25 0.17 35 0.15 50 0.15 Measurement frequency : 120Hz 6.3 4 8 Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio Stability at Low Temperature ZT / Z20 (MAX.) Z– 40°C / Z+20°C 10 3 6 16 2 4 Shelf Life Resistance to soldering heat Marking Chip Type 50 2 3 Type numbering system (Example : 16V 10µF) 1 105˚C Marking 0.5 MAX. 3 4 5 6 7 8 9 10 11 12 13 14 Taping code A±0.2 C±0.2 2 UUP 1 C 1 0 0 M C L 1 GS φD A B C E A±0.2 E φD±0.5 Voltage Plastic platform 0.3 MAX. B±0.2 Capacitance A2P 10 16V 35 2 3 The specifications listed at right shall be met Within ±20% of the initial capacitance value Capacitance change when the capacitors are restored to 20°C after tan δ 200% or less than the initial specified value the rated voltage is applied for 1000 hours at Less than or equal to the initial specified value Leakage current 105°C with the polarity every 250 hours. After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is Capacitance change Within ±10% of the initial capacitance value maintained at 250°C. The capacitors shall meet the characteristic Less than or equal to the initial specified value tan δ requirements listed at right when they are removed from the plate Less than or equal to the initial specified value Leakage current and restored to 20°C. Black print on the case top. Endurance Lot No. 25 2 4 5.8±0.3 4 1.8 4.3 4.3 1.0 (mm) 5 6.3 2.1 2.4 5.3 6.6 5.3 6.6 1.3 2.2 Configuration Capacitance tolerance (±20%) Rated capacitance (10µF) Rated voltage (16V) Series name 0.5 to 0.8 Type Voltage mark for 6.3V is 6V Dimensions Cap.(µF) 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 6.3 0J V Code 0R1 R22 R33 R47 010 2R2 3R3 4R7 100 220 330 470 5 6.3 6.3 10 1A 28 37 45 4 6.3 6.3 16 1C 17 33 41 4 5 6.3 6.3 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 12 23 37 49 5 5 6.3 35 1V 12 16 27 4 5 5 6.3 8.4 16 18 29 4 4 4 4 4 5 5 6.3 50 1H 1.0 2.0 2.8 4.0 8.4 13 17 20 Case size φ D (mm) 1 kHz 1.36 Rated ripple Rated ripple current (mArms) at 105°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 25 1E 10 kHz or more 1.50 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please select UN(p.162) series if high CV products are required. Please refer to page 3 for the minimum order quantity. CAT.8100D