ALUMINUM ELECTROLYTIC CAPACITORS UT 6mmL Chip Type , Wide Temperature Range series Chip type with load life 2000 hours at +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC). UA Long Life UT Long Life WT UX Higher C/V Specifications Item Performance Characteristics Category Temperature Range – 55 ~ +105°C Rated Voltage Range 4 ~ 50V Rated Capacitance Range 0.1 ~ 100µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater. Measurement frequency :120Hz, Temperature : 20°C tan δ 4 0.37 Rated voltage (V) tan δ (MAX.) 6.3 0.28 10 0.24 16 0.20 25 0.16 35 0.13 50 0.12 Measurement frequency :120Hz 4 6 12 Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio Z– 40°C / Z+20°C ZT / Z20 (MAX.) Stability at Low Temperature 6.3 3 8 16 2 4 25 2 3 35 2 3 50 2 3 Within ±25% of initial value (16V or less) Within ±20% of initial value (25V or more) 200% or less of initial specified value Initial specified value or less Capacitance change tan δ Leakage current After 2000 hours' application of rated voltage at 105°C , capacitors meet the characteristic requirements listed at right. Endurance 10 3 5 After leaving capacitors under no load at 105°C for 1000 hours, they meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250°C Capacitance change for 30 seconds. After removing from the hot plate and restored tan δ at room temperature, they meet the characteristic requirements Leakage current listed at right. Shelf Life Resistance to soldering heat Within ±10% of initial value Initial specified value or less Initial specified value or less Black print on the case top. Marking Type numbering system (Example : 16V 10µF) Chip Type 1 Positive 0.5 ~ 0.8 L±0.3 Voltage mark for 6.3V is φD 4 A B C E L E B±0.2 C±0.2 A±0.2 Plastic platform 0.3MAX. φD±0.5 X2P 10 16V Voltage A±0.2 Capacitance Lot No. 2 3 4 5 6 7 8 9 10 11 12 13 14 UU T 1 C 1 0 0 M C L 1 GS 0.5MAX. 105°C Marking 1.8 4.3 4.3 1.0 5.8 5 2.1 5.3 5.3 1.3 5.8 Taping code (mm) 6.3 2.4 6.6 6.6 2.2 5.8 Configuration Capacitance tolerance (±20%) Rated Capacitance (10µF) Rated voltage (16V) Series name Negative Type 6V . Dimensions 4 0G V Cap.(µF) 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 Code 0R1 R22 R33 R47 010 2R2 3R3 4R7 100 220 330 470 101 4 5 5 6.3 6.3 0J 22 30 36 60 4 5 5 6.3 10 1A 22 30 36 60 5 5 6.3 6.3 16 1C 27 35 46 60 4 5 6.3 6.3 25 1E 18 30 40 50 4 5 6.3 6.3 35 1V 13 23 38 48 4 5 6.3 50 1H 15 25 42 4 4 4 4 4 4 4 5 6.3 1.0 2.6 3.2 3.8 6.2 11 14 19 30 Case size φ D (mm) Allowable Rated ripple ripple Rated Ripple (mA rms) at 105°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz~ 1.50 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25 Please select UX(p.66), UJ(p.68) series if high C/V products are required. Please refer to page 3 for the minimum order quantity. CAT.8100U