ALUMINUM ELECTROLYTIC CAPACITORS ZT 4.5mmL Chip Type, Wide Temperature Range series WT Chip type with 4.5mm height, operating over wide temperature range of – 40 ~ +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC). Smaller ZT Smaller Specifications ZG Item Performance Characteristics Category Temperature Range – 40 ~ +105°C Rated Voltage Range 6.3 ~ 50V Rated Capacitance Range 0.1 ~ 100µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater. Measurement frequency : 120Hz, Temperature : 20°C tan δ 6.3 0.38 Rated voltage (V) tan δ (MAX.) 10 0.32 16 0.20 25 0.16 35 0.14 50 0.14 Measurement frequency : 120Hz Stability at Low Temperature 6.3 6 10 Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio Z– 40°C / Z+20°C ZT / Z20 (MAX.) 10 5 10 25 3 6 35 3 4 50 3 4 Within ±25% of initial value (16V or less) Within ±20% of initial value (25V or more) tan δ 300% or less of initial specified value Leakage current Initial specified value or less Capacitance change After 1000 hours' application of rated voltage at 105°C, capacitors meet the characteristic requirements listed at right. Endurance 16 3 6 After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250°C Capacitance change Within ±10% of initial value for 30 seconds. After removing from the hot plate and restored tan δ Initial specified value or less at room temperature, they meet the characteristic requirements Initial specified value or less Leakage current listed at right. Shelf Life Resistance to soldering heat Black print on the case top. Marking Chip Type Type numbering system (Example : 16V 10µF) 4.5 0.5 MAX. +0.1 –0.2 Voltage mark for 6.3V is 6V . 2 3 4 5 6 7 8 9 10 11 12 13 14 U Z T 1 C 1 0 0 MC L 1 GB Taping code A±0.2 A + – 0.2 φD±0.5 X2P 10 16V C±0.2 B±0.2 Plastic platform Voltage 0.3 MAX. Lot No. E Capacitance 1 Positive 105°C Marking φD A B C E 4 1.8 4.3 4.3 1.0 (mm) 5 6.3 2.1 2.4 5.3 6.6 5.3 6.6 1.3 2.2 Configuration Capacitance tolerance (±20%) Rated Capacitance (10µF) Rated voltage (16V) Series name Negative 0.5 ~ 0.8 Type Dimensions 6.3 0J V Cap. (µF) 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 Code 0R1 R22 R33 R47 010 2R2 3R3 4R7 100 220 330 470 101 4 5 5 6.3 10 1A 19 26 32 52 5 5 6.3 16 1C 24 30 40 4 5 6.3 6.3 25 1E 16 26 35 44 4 5 6.3 6.3 35 1V 11 20 33 42 4 5 6.3 50 1H 13 22 36 4 4 4 4 4 4 4 5 6.3 Case size φ D (mm) 0.9 2.2 2.8 3.3 5.4 9.6 12 16 26 Rated ripple Rated Ripple (mArms) at 105°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz~ 1.50 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please select UX(p.74), UJ(p.76) series if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. CAT.8100V