ALUMINUM ELECTROLYTIC CAPACITORS WG Chip Type, Low Impedance series Chip type, operating over wide temperature range of to – 55 ~ +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC). Low Impedance UD Low Impedance WG WF Specifications Item Performance Characteristics Category Temperature Range – 55 ~ +105°C Rated Voltage Range 6.3 ~ 50V Rated Capacitance Range 1 ~ 1500µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater. Measurement frequency : 120Hz, Temperature : 20°C tan δ 6.3 0.26 Rated voltage (V) tan δ (MAX.) 10 0.19 16 0.16 25 0.14 35 0.12 50 0.12 Measurement frequency : 120Hz 6.3 2 4 Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio Z– 55°C / Z+20°C ZT / Z20 (MAX.) Stability at Low Temperature After 1000 hours' application of rated voltage at 105°C, capacitors meet the characteristic requirements listed at right. Endurance 10 2 4 16 2 3 25 2 3 35 2 3 50 2 3 Capacitance change Within ±20% of initial value tan δ 200% or less of initial specified value Leakage current Initial specified value or less After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250°C Capacitance change Within ±10% of initial value for 30 seconds. After removing from the hot plate and restored Initial specified value or less tan δ at room temperature, they meet the characteristic requirements Leakage current Initial specified value or less listed at right. Shelf Life Resistance to soldering heat Black print on the case top. Marking Type numbering system (Example : 10V 100µF) Chip Type A±0.2 A±0.2 L±0.5 Pressure relief vent C±0.2 B±0.2 D±0.5 f X2P 220 25V Lot No. Voltage mark for 6.3V is 6V . Positive Plastic platform 0.3 MAX. Voltage Negative H 0.5 MAX. (f8 ´ 10, f10 ´ 10 ) E A±0.2 A±0.2 B±0.2 D±0.5 f X2P 100 10V C±0.2 L±0.3 Lot No. Capacitance 105¡C Marking Trade mark Positive Plastic platform 0.3 MAX. Voltage Negative H f A B C E L H D´L (mm) 4 ´ 5.4 5 ´ 5.4 6.3 ´ 5.4 8 ´ 6.2 8 ´ 10 10 ´ 10 3.2 2.9 3.3 2.4 2.1 1.8 10.3 8.3 8.3 6.6 5.3 4.3 10.3 8.3 8.3 6.6 5.3 4.3 4.5 3.1 2.3 2.2 1.3 1.0 10 10 6.2 5.4 5.4 5.4 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.8 ~ 1.1 0.8 ~ 1.1 E (f8 ´ 6.2 ) Taping code fD code 4 ~ 6.3 GB 8 ¥ 10 GS Configuration Capacitance tolerance (±20%) 4 ~fD6.3 code CL Rated Capacitance (100µF) 8 (6.2L) CL Rated voltage (10V) 8 (10L) ¥ 10 NL Series name Type A±0.2 A±0.2 B±0.2 D±0.5 f X2P 100 6V C±0.2 L +0.1 -0.2 Lot No. Capacitance 105¡C Marking Trade mark 0.5 MAX. Plastic platform 0.3 MAX. Voltage E Capacitance 105¡C Marking 1 2 3 4 5 6 7 8 9 10 11 12 13 14 UWG 1 A 1 0 1 M C L 1 G S Positive 0.5 MAX. (f4 ~ 6.3) H Negative Dimension table in next page. CAT.8100V ALUMINUM ELECTROLYTIC CAPACITORS WG series Dimensions Cap. (µF) V 6.3 10 16 Code 0J 1A 1C 4 × 5.4 3.0 60 5 × 5.4 1.8 95 95 6.3 × 5.4 1.0 140 140 8 × 6.2 0.4 230 8 × 6.2 0.4 230 10 × 10 0.15 670 10 × 10 0.15 670 10 × 10 0.15 670 10 × 10 0.15 670 10 100 22 220 33 330 47 470 5 × 5.4 1.8 68 680 6.3 × 5.4 1.0 100 101 6.3 × 5.4 1.0 140 150 151 220 221 8 × 6.2 0.4 230 330 331 8 × 10 0.3 450 470 471 680 681 1000 102 10 × 10 0.15 670 1500 152 10 × 10 0.15 670 Cap. (µF) 4 × 5.4 60 3.0 5 × 5.4 1.8 95 8 × 6.2 0.4 230 8 × 6.2 0.4 230 8 × 10 0.3 450 10 × 10 10 × 10 0.15 0.15 670 670 V 25 35 50 Code 1E 1V 1H 1 010 4 × 5.4 3.0 60 4 × 5.4 5.0 30 2.2 2R2 4 × 5.4 3.0 60 4 × 5.4 5.0 30 3.3 3R3 4 × 5.4 3.0 60 4 × 5.4 5.0 30 4.7 4R7 4 × 5.4 3.0 60 5 × 5.4 3.0 50 6.8 6R8 95 4 × 5.4 3.0 60 5 × 5.4 1.8 5 × 5.4 1.8 95 6.3 × 5.4 2.0 70 6.3 × 5.4 1.0 140 8 × 6.2 0.7 120 10 100 22 220 6.3 × 5.4 1.0 140 33 330 6.3 × 5.4 1.0 140 8 × 6.2 0.4 230 8 × 10 0.6 300 47 470 8 × 6.2 0.4 230 8 × 6.2 0.4 230 10 × 10 0.3 500 68 680 8 × 10 0.3 450 100 101 8 × 10 0.3 450 10 × 10 0.15 670 10 × 10 0.3 500 220 221 10 × 10 0.15 670 10 × 10 0.15 670 10 × 10 0.3 500 330 331 10 × 10 0.15 670 10 × 10 0.15 670 470 471 10 × 10 0.15 670 Case size φ D × L (mm) Impedance Rated ripple Max. Impedance (Ω) at 20°C 100kHz Rated Ripple (mArms) at 105°C 100kHz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.35 120 Hz 0.50 300 Hz 0.64 1 kHz 0.83 10 kHz~ 1.00 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please select UJ(p.76) series if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. CAT.8100V