Advance Information W27LE520 64K × 8 ELECTRICALLY ERASABLE EPROM GENERAL DESCRIPTION The W27LE520 is a high speed, low power Electrically Erasable and Programmable Read Only Memory organized as 65,536 × 8 bits. It includes latches for the lower 8 address lines to multiplex with the 8 data lines. To cooperate with the MCU, this device could save the external TTL component, also cost and space. It requires only one supply in the range of 3.0V to 3.6V or 4.5V to 5.5V in normal read mode. The W27LE520 provides an electrical chip erase function. It will be a great convenient when you need to change/update the contents in the device. FEATURES • High speed access time: 70/90 nS (max.) • Read operating current: 8 mA/20 mA (max.) • Erase/Programming operating current 30 mA (max.) • Standby current: 20 µA /100 µA (max.) • Unregulated battery power supply range, 3.0V to 3.6V or 4.5V to 5.5V • +13V erase and programming voltage PIN CONFIGURATIONS 1 20 A8 A12 2 19 AD1 A14 3 18 AD3 ALE VDD 4 17 AD5 5 TSSOP 16 Top View AD7 15 GND 7 14 AD6 A13 8 13 AD4 A11 9 12 AD2 A9 10 11 AD0 6 A15 compatible • Three-state outputs • Available packages: 20-pin TSSOP and 20-pin SOP BLOCK DIAGRAM A10 OE/VPP • High Reliability CMOS Technology - 2K V ESD Protection - 200 mA Latchup Immunity • Fully static operation • All inputs and outputs directly LVTTL/CMOS ALE CONTROL OE / VPP L A T C H E S AD7 - AD0 DECODER OUTPUT BUFFER MEMORY ARRAY A15 - A8 VDD GND OE/VPP A15 1 20 VDD 2 19 ALE A13 3 18 A14 A11 4 17 A12 SOP 16 Top View A10 A9 5 AD0 6 AD2 7 14 AD1 AD4 8 13 AD6 GND 9 12 AD3 AD5 10 11 AD7 15 PIN DESCRIPTION SYMBOL AD0−AD7 A8−A15 ALE A8 OE/VPP VDD GND -1- DESCRIPTION Address/Data Inputs/Outputs Address Inputs Address Latch Enable Output Enable, Program/Erase Supply Voltage Power Supply Ground Publication Release Date: 4/26/2000 Revision A1 Advance Information W27LE520 FUNCTIONAL DESCRIPTION Read Mode Unlike conventional UVEPROMs, which has CE and OE two control functions, the W27LE520 has one OE/VPP and one ALE (address_latch_enable) control functions. The ALE makes lower address A[7:0] to be latched in the chip when it goes from high to low, so that the same bus can be used to output data during read mode. i.e. lower address A[7:0] and data bus DQ[7:0] are multiplexed. OE/VPP controls the output buffer to gate data to the output pins. When addresses are stable, the address access time (TACC) is equal to the delay from ALE to output (TCE), and data are available at the outputs TOE after the falling edge of OE/VPP, if TACC and TCE timings are met. Erase Mode The erase operation is the only way to change data from "0" to "1." Unlike conventional UVEPROMs, which use ultraviolet light to erase the contents of the entire chip (a procedure that requires up to half an hour), the W27LE520 uses electrical erasure. Generally, the chip can be erased within 100 mS by using an EPROM writer with a special erase algorithm. There are two ways to enter Erase mode. One is to raise OE/VPP to VPE (13V), VDD = VDE (6.5V), A9 = VHH (13V), A10 = high A8&A11 = low, and all other address pins include AD[7:0] keep at fixed low or high. Pulsing ALE high starts the erase operation. The other way is somewhat like flash, by programming two consecutive commands into the device and then enter Erase mode. The two commands are loading Data = AA(hex) to Addr. = 5555(hex) and Data = 10(hex) to Addr. = 2AAA(hex). Be careful to note that the ALE pulse widths of these two commands are different: One is 50uS, while the other is 100mS. Please refer to the Smart Erase Algorithm 1 & 2. Erase Verify Mode The device will enter the Erase Verify Mode automatically after Erase Mode. Only power down the device can force the device enter Normal Read Mode again. Program Mode Programming is the only way to change cell data from "1" to "0." The program mode is entered when OE/VPP is raised to VPP (13V), VDD = VDP (6.5V), the address pins equal the desired addresses, and the input pins equal the desired inputs. Pulsing ALE high starts the programming operation. Program Verify Mode The device will enter the Program Verify Mode automatically after Program Mode. Only power down the device can force the device enter Normal Read Mode again. Erase/Program Inhibit Erase or program inhibit mode allows parallel erasing or programming of multiple chips with different data. When ALE low, erasing or programming of non-target chips is inhibited, so that except for the ALE and OE/VPP pins, the W27LE520 may have common inputs. Standby Mode The standby mode significantly reduces VDD current. This mode is entered when ALE and OE/VPP keep high. In standby mode, all outputs are in a high impedance state. System Considerations -2- Advance Information W27LE520 An EPROM's power switching characteristics require careful device decoupling. System designers are interested in three supply current issues: standby current levels (ISB), active current levels (IDD), and transient current peaks produced by the falling and rising edges of ALE Transient current magnitudes depend on the device output's capacitive and inductive loading. Proper decoupling capacitor selection will suppress transient voltage peaks. Each device should have a 0.1 µF ceramic capacitor connected between its VDD and GND. This high frequency, low inherentinductance capacitor should be placed as close as possible to the device. Additionally, for every eight devices, a 4.7 µF electrolytic capacitor should be placed at the array's power supply connection between VDD and GND. The bulk capacitor will overcome voltage slumps caused by PC board trace inductances. TABLE OF OPERATING MODES (VPP = 13V, VPE = 13V, VHH = 12V, VDP = 6.5V, VDE = 6.5V, VDD = 3.3V or 5.0V, VDI = 5.0V, X = VIH or VIL) MODE OE/VPP PIN OTHER ADDRESS VDD VIH VIH X VDD A[7:0] Read VIL VIL AIN VDD DOUT Output Disable VIL VIH X VDD High Z Standby VIH VIH AIN VDD A[7:0] Program VIH VPP AIN VDP DIN Erase 1 VIH VPE A8&A11 = VIL, A9 = VPE, A10 = VIH, Others = X VDE X Erase 2 VIH VPE First command: Addr. = 5555 (hex) VDE AA(hex) Secon command: Addr. = 2AAA (hex) VDE 10(hex) ALE Address Latch Enable AD[7:0] Product Identifiermanufacturer VIL VIL A8 = VIL, A9 = VHH, Others = X VDI DA(Hex) Product Identifier-device VIL VIL A8 = VIH, A9 = VHH, Others = X VDI 1F(Hex) -3- Publication Release Date: 4/26/2000 Revision A1 Advance Information W27LE520 DC CHARACTERISTICS Absolute Maximum Ratings PARAMETER Ambient Temperature with Power Applied Storage Temperature Voltage on all Pins with Respect to Ground Except OE/VPP, A9 and VDD Pins Voltage on OE/VPP Pin with Respect to Ground Voltage on A9 Pin with Respect to Ground Voltage VDD Pin with Respect to Ground RATING -55 to +125 -65 to +150 -2.0 to +7.0 UNIT °C °C V -2.0 to +7.0 -2.0 to +7.0 -2.0 to +14.0 V V V Note: 1. Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely affect the life and reliability of the device. 2. Minimum voltage is -0.6V DC which may undershoot to -2.0V for pulses of less than 20ns. Maximum output pin voltage is VDD+0.75V DC which may overshoot to +7.0V for pulses of less than 20ns. DC Erase Characteristics (TA = 25° C ±5° C, VDD = 6.5V ±0.25V) PARAMETER SYM. CONDITIONS Input Load Current VDD Erase Current ILI ICP VPP Erase Current IPP Input Low Voltage Input High Voltage Output Low Voltage (Verify) Output High Voltage (Verify) A9 SID Voltage A9 Erase Voltage VPP Erase Voltage VDD Supply Voltage (Erase & Erase Verify) VIL VIH VOL VIN = VIL or VIH ALE = VIH, OE/VPP = VPE A8&A11 = VIL, A9 = VPE, A10 = VIH, Others = X ALE = VIH, OE/VPP = VPE A8&A11 = VIL, A9 = VPE, A10 = VIH, Others = X IOL = 2.1 mA VOH IOH = -0.4 mA VHH VPE VPE VDE VDD = 5V ± 10% - MIN. -10 - LIMITS TYP. MAX. 10 30 UNIT µA mA - - 30 mA -0.3 2.4 - - 0.8 VDD+0.3 0.45 V V V 2.4 - - - 11.5 12.75 12.75 6.25 12 13 13 6.5 12.5 13.25 13.25 6.75 V V V V Note: VDD must be applied simultaneously or before VPP and removed simultaneously or after VPP. CAPACITANCE (VDD = 3.0V to 3.6V or 4.5V to 5.5V, TA = 25° C, f = 1 MHz) PARAMETER Input Capacitance Output Capacitance SYMBOL CIN COUT VIN = 0V VOUT = 0V -4- MAX. 6 12 UNIT pF pF Advance Information W27LE520 AC CHARACTERISTICS AC Test Conditions PARAMETER Input Pulse Levels Input Rise and Fall Times Input and Output Timing Reference Level Output Load CONDITIONS 0V/3V 10 nS 1.5V/1.5V CL = 100 pF, IOH/IOL = -0.4 mA/2.1 mA AC Test Load and Waveforms +1.3V (IN914) 3.3K ohm DOUT 100 pF (Including Jig and Scope) Input Output Test Points Test Points 3V 1.5V 1.5V 0V -5- Publication Release Date: 4/26/2000 Revision A1 Advance Information W27LE520 READ OPERATION DC CHARACTERISTICS (VDD = 3.0V to 3.6V or 4.5V to 5.5V, TA = 0 to 70° C) PARAMETER SYM. CONDITIONS MIN. Input Load Current Output Leakage Current Standby VDD Current (CMOS input) ILI ILO ISB VIN = 0V to VDD VOUT = 0V to VDD ALE = VDD ±0.3V, OE/VPP = VDD ±0.3V All others inputs = GND/ VDD ±0.3V VDD = 3.0V to 3.6V VDD = 4.5V to 5.5V VDD Operating Current IDD Input Low Voltage Input High Voltage VIL VIH Output Low Voltage Output High Voltage VOL VOH VDD = 3.0V to 3.6V VDD = 4.5V to 5.5V ALE = VIL, IOUT = 0 mA f = 5 MHz IOL = 2.1 mA IOH = -0.4 mA -5 -5 - LIMITS TYP. MAX . 5 5 20 - 100 - - 8 - - 20 -0.6 2.0 - 2.4 - 0.8 VDD +0.3 0.4 - UNIT µA µA µA mA V V V V READ OPERATION AC CHARACTERISTICS (VDD = 3.0V to 3.6V or 4.5V to 5.5V, TA = 0 to 70° C) PARAMETER Address Latch Enable Access Time Address Latch Enable Width Address Access Time Address Setup Time Address Hold Time Output Enable Access Time OE /VPP High to High-Z Output Output Hold from Address Change SYM. TCE TALE TACC TAS TAH TOE TDF TOH W27LE520-70 MIN. MAX. 45 15 15 0 70 70 35 25 - W27LE520-90 MIN. MAX . 90 45 90 15 15 35 25 0 - Note: VDD must be applied simultaneously or before VPP and removed simultaneously or after VPP. -6- UNIT nS nS nS nS nS nS nS nS Advance Information W27LE520 DC PROGRAMMING CHARACTERISTICS (VDD = 6.5V ±0.25V, TA = 25° C ±5° C) PARAMETER SYM. CONDITIONS LIMITS UNIT MIN. -10 TYP. - MAX. 10 ALE = VIH, - - 30 µA mA OE /VPP = VPP ALE = VIH, - - 30 mA -0.3 2.4 2.4 11.5 12.0 0.8 VDD+0.5 0.45 12.5 V V V V V 12.75 6.25 13.0 6.5 13.25 6.75 V V MIN. LIMITS TYP. MAX. Input Load Current ILI VIN = VIL or VIH VDD Program Current ICP VPP Program Current IPP Input Low Voltage Input High Voltage Output Low Voltage (Verify) Output High Voltage (Verify) A9 Silicon I.D. Voltage VIL VIH VOL VOH VHH VPP Program Voltage VDD Supply Voltage (Program) VPP VDP OE /VPP = VPP IOL = 2.1 mA IOH = -0.4 mA VDD = 5V ± 10% - AC PROGRAMMING/ERASE CHARACTERISTICS (VDD = 6.5V ±0.25V, TA = 25° C ±5° C) PARAMETER SYM. UNIT OE /VPP Pulse Rise Time Address Latch Enable Width ALE Program Pulse Width TPRT 50 - - nS TALE TPPW 500 47.5 50 52.5 nS ALE Erase Pulse Width ALE Erase Pulse Width 1 TEPW TEPW1 95 47.5 100 50 105 52.5 ALE Erase Pulse Width 2 Latched Address Setup Time Latched Address Hold Time Address Setup Time TEPW2 TLAS TLAH TAS 95 100 100 2.0 100 - 105 - Address Hold Time TAH 0 - - µS OE /VPP Setup Time TOES 2.0 - - µS OE /VPP Hold Time Data Setup Time Data Hold Time TOEH 2.0 - - µS Data Valid from OE /VPP Low during Erase Verify TDS TDH TEOE 2.0 2.0 - - 150 µS µS nS Data Valid from OE /VPP Low during Program Verify TPOE - - 150 nS OE /VPP High to Output High Z TDFP 0 - 130 nS OE /VPP High Voltage Delay After ALE Low TVS 2.0 - - µS OE /VPP Recovery Time TVR 2.0 - - µS µS mS µS mS nS nS µS Note: VDD must be applied simultaneously or before VPP and removed simultaneously or after VPP. -7- Publication Release Date: 4/26/2000 Revision A1 Advance Information W27LE520 TIMING WAVEFORMS AC Read Waveform VIH A8-A15 Address Valid VIL TALE ALE VIH VIL TCE VIH TOE OE/Vpp TDF VIL TAS TOH High Z High Z AD0-AD7 TAH Data Address TACC Programming Waveform PROGRAM A[15:8] TAS VIH TAH Address Stable V IL TRPT 13V OE/Vpp PROGRAM (VERIFY) VIH TOES TOEH V IL TVR TVS ALE VIH V IL AD[7:0] VIH V IL TALE TPPW TALE TLAH TLAS Add TDH T DS TPOE Add Data in -8- TDFP Data out Advance Information W27LE520 Timing Waveforms, continued Erase Waveform 1 Read Device SID Read Company SID Chip Erase A9 = 13.0V Others = VILor VIH A8, A11 = VIL A10 = VIH Others = VIL or VIH V IH A8 = VIL V IL VDD = 6.5V VDD = 6.5V VDD = 3.3 or 5.0V A9 = 12.0V A[15:8] Erase (Verify) A8 = VIH Address Valid V IH AD[7:0] DA V IL 13.0V 1F Add TPRT TVR DOUT TEOE V IH OE/Vpp V IL TOEH TOES V IH ALE V IL TEPW Erase Waveform 2 Read Company SID Read Device SID Chip Erase Command 1 VDD =6.5V VDD =3.3 or 5.0V A9=12.0 V Command 2 Erase Verify VDD =6.5V VDD =6.5V TAS A[15:8] V IH V IL Others=V IL or V IH A8=V IL A[15:8] = 55 A8=V IH V IH V IL Address Valid TRPT 13.0V OE/Vpp A[15:8] = 2A DA 1F Add TOES DOUT TOEH TVS TPRT TEOE V IH ALE V IL TALE TOES V IH AD[7:0] V IL TEPW1 TLAH TLAS 55 TDS TEPW2 TDH AA AA 10 Note: First command Address = 5555(hex) with Data = AA(hex) Second command Address = 2AAA(hex) with Data = 10(hex) -9- Publication Release Date: 4/26/2000 Revision A1 Advance Information W27LE520 SMART PROGRAMMING ALGORITHM 1 Start Address = First Location VDD = 6.5V OE/Vpp = 13V Program One 50 µ S Pulse Increment Address No Last Address ? Yes Address = First Location Increment Address X=0 No Last Address ? Pass Fail Verify Byte Increment X Yes Power Down No Program One 50 µ S Pulse X = 25 ? VDD = 3.3 or 5.0V OE/Vpp = VIL Yes Compare All Bytes to Original Data Pass Device Passed - 10 - Fail Device Failed Advance Information W27LE520 SMART PROGRAMMING ALGORITHM 2 Start Address = First Location VDD = 6.5V X=0 Program One 50 µS Pulse OE/Vpp = 13V Increment X X = 25? Yes No Fail Verify One Byte OE/Vpp = V IL Verify One Byte OE/Vpp = V IL Pass Increment Address Fail Pass No Last Address ? Yes Power Down VDD =3.3or5.0V Compare All Bytes to Original Data Fail Pass Device Passed - 11 - Device Failed Publication Release Date: 4/26/2000 Revision A1 Advance Information W27LE520 SMART ERASE ALGORITHM 1 Start X=0 VDD= 6.5V OE/Vpp = 13V A9 = 13V; A8&A11 = V IL A10 = V IH Chip Erase 100 mS Pulse Address = First Location Increment X V DD= 6.5V OE/Vpp = V IL No Fail Erase Verify X = 20? Pass Yes Increment Address No Last Address? Yes Power Down V DD= 3.3 or 5.0V OE/Vpp = V IL Compare All Bytes to FFs (HEX) Fail Pass Pass Device Fail Device - 12 - Advance Information W27LE520 SMART ERASE ALGORITHM 2 Start X=0 VDD = 6.5V OE/Vpp = 13V Program One 50µ S Pulse with Address = 5555(Hex) Data = AA(Hex) Program One 100 mS Pulse with Address = 2AAA(Hex) Data = 10(Hex) Increment X VDD = 6.5V OE/Vpp = V IL No Fail Erase Verify X = 20? Pass Yes Increment Address No Last Address? Yes Power Down VDD = 3.3 or 5.0V OE/Vpp = V IL Compare All Bytes to FFs (HEX) Fail Pass Fail Device Pass Device - 13 - Publication Release Date: 4/26/2000 Revision A1 Advance Information W27LE520 ORDERING INFORMATION PART NO. W27LE520W-70* W27LE520W-90* W27LE520S-70* W27LE520S-90* ACCESS TIME (nS) 70 90 70 90 OPERATING CURRENT MAX. (mA) 8/20 8/20 8/20 8/20 STANDBY CURRENT MAX. (µ µ A) 20/100 20/100 20/100 20/100 PACKAGE 173mil TSSOP 173mil TSSOP 300mil SOP 300mil SOP Notes: 1. The Part No is preliminary and might be changed after project is consoled. 2. Winbond reserves the right to make changes to its products without prior notice. 3. Purchasers are responsible for performing appropriate quality assurance testing on products intended for use in applications where personal injury might occur as a consequence of product failure. - 14 - Advance Information W27LE520 PACKAGE DIMENSIONS 20-pin TSSOP c L b Dimension in Inches Symbol E1 E θ e A Nom. Max. Dimension in mm Min. Nom. Max. 0.043 1.10 A A1 0.002 0.006 0.05 0.15 L 0.020 0.028 0.50 0.70 D E E1 0.252 0.260 6.40 6.60 0.246 0.256 6.25 6.50 0.169 0.176 4.30 4.48 0.007 0.012 0.18 0.30 0.003 0.007 0.09 0.18 8 0 b c e θ D Min. 0.65 BSC 0 0.256 BSC 8 A1 20-pin SOP c L b Dimension in Inches Symbol E1 E θ e D A Min. Nom. Max. 0.092 Dimension in mm Min. Nom. Max. 0.105 2.34 2.67 A A1 0.003 0.012 0.076 0.305 L 0.015 0.035 0.381 0.889 D 0.497 0.513 12.6 13.0 E E1 b c e θ 0.393 0.420 9.98 10.7 0.291 0.299 7.60 7.39 0.013 0.020 0.330 0.508 0.009 0.013 0.229 0.330 1.27 BSC 0.50 BSC 0 8 0 8 A1 - 15 - Publication Release Date: 4/26/2000 Revision A1 Advance Information W27LE520 VERSION HISTORY VERSION A1 DATE 4/26/2000 PAGE - DESCRIPTION Initial Issued Headquarters Winbond Electronics (H.K.) Ltd. No. 4, Creation Rd. III, Science-Based Industrial Park, Hsinchu, Taiwan TEL: 886-3-5770066 FAX: 886-3-5796096 http://www.winbond.com.tw/ Voice & Fax-on-demand: 886-2-7197006 Rm. 803, World Trade Square, Tower II, 123 Hoi Bun Rd., Kwun Tong, Kowloon, Hong Kong TEL: 852-27513100 FAX: 852-27552064 Taipei Office 11F, No. 115, Sec. 3, Min-Sheng East Rd., Taipei, Taiwan TEL: 886-2-7190505 FAX: 886-2-7197502 Note: All data and specifications are subject to change without notice. - 16 - Winbond Electronics North America Corp. Winbond Memory Lab. Winbond Microelectronics Corp. Winbond Systems Lab. 2727 N. First Street, San Jose, CA 95134, U.S.A. TEL: 408-9436666 FAX: 408-5441798