WINBOND W78E58B

W78E58B/W78E058B Data Sheet
8-BIT MICROCONTROLLER
Table of Contents1. GENERAL DESCRIPTION ............................................................................................................... 3
2. FEATURES ....................................................................................................................................... 3
3. PIN CONFIGURATIONS .................................................................................................................. 4
4. PIN DESCRIPTION .......................................................................................................................... 5
5. FUNCTIONAL DESCRIPTION ......................................................................................................... 6
5.1
RAM ....................................................................................................................................... 6
5.2
Timers 0, 1 and 2................................................................................................................... 6
5.3
Clock ...................................................................................................................................... 7
5.4
Crystal Oscillator.................................................................................................................... 7
5.5
External Clock........................................................................................................................ 7
5.6
Power Management............................................................................................................... 7
5.7
Reduce EMI Emission ........................................................................................................... 7
5.8
Reset...................................................................................................................................... 7
5.9
Port 4 ..................................................................................................................................... 9
5.10
INT2 / INT3 ............................................................................................................................ 9
5.11
Port 4 Base Address Registers ........................................................................................... 11
5.12
In-System Programming (ISP) Mode................................................................................... 13
5.13
In-System Programming Control Register (CHPCON) ....................................................... 15
5.14
F04KBOOT Mode (Boot From LDROM) ............................................................................. 15
6. SECURITY ...................................................................................................................................... 19
6.1
Lock Bit ................................................................................................................................ 19
6.2
MOVC Inhibit ....................................................................................................................... 19
6.3
Encryption ............................................................................................................................ 20
6.4
Oscillator Control ................................................................................................................. 20
7. ELECTRICAL CHARACTERISTICS............................................................................................... 21
7.1
Absolute Maximum Ratings ................................................................................................. 21
7.2
D.C. Characteristics............................................................................................................. 21
7.3
A.C. Characteristics ............................................................................................................. 23
7.3.1
Clock Input Waveform...........................................................................................................23
7.3.2
Program Fetch Cycle ............................................................................................................23
7.3.3
Data Read Cycle...................................................................................................................24
7.3.4
Data Write Cycle ...................................................................................................................24
7.3.5
Port Access Cycle.................................................................................................................24
-1-
Publication Release Date: December 4, 2006
Revision A8
W78E58B/W78E058B
8. TIMING WAVEFORMS................................................................................................................... 25
8.1
Program Fetch Cycle ........................................................................................................... 25
8.2
Data Read Cycle.................................................................................................................. 25
8.3
Data Write Cycle.................................................................................................................. 26
8.4
Port Access Cycle................................................................................................................ 26
9. TYPICAL APPLICATION CIRCUITS .............................................................................................. 27
9.1
Expanded External Program Memory and Crystal .............................................................. 27
9.2
Expanded External Data Memory and Oscillator ................................................................ 28
10. PACKAGE DIMENSIONS............................................................................................................... 29
10.1
40-pin DIP............................................................................................................................ 29
10.2
44-pin PLCC ........................................................................................................................ 29
10.3
44-pin PQFP ........................................................................................................................ 30
11. APPLICATION NOTES................................................................................................................... 31
11.1
In-system Programming Software Examples ...................................................................... 31
12. REVISION HISTORY...................................................................................................................... 36
-2-
W78E58B/W78E058B
1. GENERAL DESCRIPTION
The W78E058B is an 8-bit microcontroller which has an in-system programmable Flash EPROM for
firmware updating. The instruction set of the W78E058B is fully compatible with the standard 8052.
The W78E058B contains a 32K bytes of main ROM and a 4K bytes of auxiliary ROM which allows the
contents of the 32KB main ROM to be updated by the loader program located at the 4KB auxiliary
ROM; 512 bytes of on-chip RAM; four 8-bit bi-directional and bit-addressable I/O ports; an additional
4-bit port P4; three 16-bit timer/counters; a serial port. These peripherals are supported by a eight
sources two-level interrupt capability. To facilitate programming and verification, the ROM inside the
W78E058B allows the program memory to be programmed and read electronically. Once the code is
confirmed, the user can protect the code for security.
The W78E058B microcontroller has two power reduction modes, idle mode and power-down mode,
both of which are software selectable. The idle mode turns off the processor clock but allows for
continued peripheral operation. The power-down mode stops the crystal oscillator for minimum power
consumption. The external clock can be stopped at any time and in any state without affecting the
processor.
2. FEATURES
y
Fully static design 8-bit CMOS microcontroller
y
32K bytes of in-system programmable Flash EPROM for Application Program (APROM)
y
4K bytes of auxiliary ROM for Loader Program (LDROM)
y
512 bytes of on-chip RAM (including 256 bytes of AUX-RAM, software selectable)
y
64K bytes program memory address space and 64K bytes data memory address space
y
Four 8-bit bi-directional ports
y
One 4-bit multipurpose programmable port
y
Three 16-bit timer/counters
y
One full duplex serial port
y
Eight-sources, two-level interrupt capability
y
Built-in power management
y
Code protection
y
Packaged in
− Lead Free (RoHS) DIP 40:
W78E058B40DL
− Lead Free (RoHS) PLCC 44: W78E058B40PL
− Lead Free (RoHS) PQFP 44: W78E058B40FL
-3-
Publication Release Date: December 4, 2006
Revision A8
W78E58B/W78E058B
3. PIN CONFIGURATIONS
40-Pin DIP
T2, P1.0
1
40
T2EX, P1.1
2
39
P0.0, AD0
P1.2
3
38
P0.1, AD1
P1.3
4
37
P0.2, AD2
P1.4
5
36
P0.3, AD3
P1.5
6
35
P0.4, AD4
P1.6
7
34
P0.5, AD5
P1.7
8
33
P0.6, AD6
RST
9
32
P0.7, AD7
RXD, P3.0
10
31
TXD, P3.1
11
30
EA
ALE
INT0, P3.2
12
29
PSEN
INT1, P3.3
13
28
P2.7, A15
T0, P3.4
14
27
P2.6, A14
T1, P3.5
15
26
P2.5, A13
WR, P3.6
16
25
P2.4, A12
RD, P3.7
17
24
P2.3, A11
XTAL2
18
23
P2.2, A10
XTAL1
19
22
P2.1, A9
VSS
20
21
P2.0, A8
44-Pin QFP
44-Pin PLCC
P
1
.
4
P
1
.
3
P
1
.
2
T
2
E
X
,
P
1
.
1
6
5
4
3
T
2
,
P
1
.
0
2
/
I
N
T
3
,
P
4 V
. D
2 D
A
D
0
,
P
0
.
0
A
D
1
,
P
0
.
1
A
D
2
,
P
0
.
2
A
D
3
,
P
0
.
3
P
1
.
4
P1.5
7
P1.6
8
1 44 43 42 41 40
39
38
P1.7
9
37
P0.7, AD7
P0.4, AD4
P0.5, AD5
P0.6, AD6
RST
10
36
RXD, P3.0
11
35
EA
INT2, P4.3
TXD, P3.1
12
34
P4.1
13
33
ALE
INT0, P3.2
14
32
INT1, P3.3
15
31
T0, P3.4
T1, P3.5
30
16
29
17
18 19 20 21 22 23 24 25 26 27 28
P
3
.
6
,
/
W
R
P
3
.
7
,
/
R
D
X
T
A
L
2
X
T
A
L
1
VDD
V
S
S
P
4
.
0
P
2
.
0
,
A
8
P
2
.
1
,
A
9
P
2
.
2
,
A
1
0
P
2
.
3
,
A
1
1
PSEN
P2.7, A15
-4-
A
D
1
,
P
0
.
1
A
D
2
,
P
0
.
2
A
D
3
,
P
0
.
3
44 43 42 41 40 39 38 37 36 35 34
33
P0.4, AD4
P1.6
2
32
P0.5, AD5
P1.7
3
31
P0.6, AD6
RST
4
30
P0.7, AD7
RXD, P3.0
5
29
EA
INT2, P4.3
6
28
P4.1
ALE
TXD, P3.1
7
27
INT0, P3.2
8
26
INT1, P3.3
9
25
PSEN
P2.7, A15
10
11
24
23
P2.6, A14
12 13 14 15 16 17 18 19 20 21 22
P
3
.
6
,
/
W
R
P
2
.
4
,
A
1
2
A
D
0
,
P
0
.
0
1
T1, P3.5
P2.5, A13
T
2
,
P
1
.
0
/
I
N
T
3
,
P
4 V
. D
2 D
P1.5
T0, P3.4
P2.6, A14
P
1
.
3
T
2
E
X
,
P P
1 1
. .
2 1
P
3
.
7
,
/
R
D
X
T
A
L
2
X
T
A
L
1
V
S
S
P
4
.
0
P
2
.
0
,
P
2
.
1
,
A A
8 9
P
2
.
2
,
A
1
0
P
2
.
3
,
A
1
1
P
2
.
4
,
A
1
2
P2.5, A13
W78E58B/W78E058B
4. PIN DESCRIPTION
SYMBOL
TYPE
DESCRIPTIONS
EA
I
EXTERNAL ACCESS ENABLE: This pin forces the processor to execute the
external ROM. The ROM address and data will not be presented on the bus if
the EA pin is high.
PSEN
O H
PROGRAM STORE ENABLE: PSEN enables the external ROM data in the
Port 0 address/data bus. When internal ROM access is performed, no PSEN
strobe signal outputs originate from this pin.
ALE
O H
ADDRESS LATCH ENABLE: ALE is used to enable the address latch that
separates the address from the data on Port 0. ALE runs at 1/6th of the
oscillator frequency.
RST
I L
RESET: A high on this pin for two machine cycles while the oscillator is
running resets the device.
XTAL1
I
CRYSTAL 1: This is the crystal oscillator input. This pin may be driven by an
external clock.
XTAL2
O
CRYSTAL 2: This is the crystal oscillator output. It is the inversion of XTAL1.
VSS
I
GROUND: Ground potential.
VDD
I
POWER SUPPLY: Supply voltage for operation.
P0.0 − P0.7
I/O D PORT 0: Function is the same as that of standard 8052.
P1.0 − P1.7
I/O H PORT 1: Function is the same as that of standard 8052.
P2.0 − P2.7
I/O H
P3.0 − P3.7
I/O H PORT 3: Function is the same as that of the standard 8052.
P4.0 − P4.3
I/O H PORT 4: A bi-directional I/O. See details below.
PORT 2: Port 2 is a bi-directional I/O port with internal pull-ups. This port also
provides the upper address bits for accesses to external memory.
* Note: TYPE I: input, O: output, I/O: bi-directional, H: pull-high, L: pull-low, D: open drain
-5-
Publication Release Date: December 4, 2006
Revision A8
W78E58B/W78E058B
5. FUNCTIONAL DESCRIPTION
The W78E058B architecture consists of a core controller surrounded by various registers, four general
purpose I/O ports, one special purpose programmable 4-bits I/O port, 512 bytes of RAM, three
timer/counters, a serial port. The processor supports 111 different opcodes and references both a 64K
program address space and a 64K data storage space.
5.1
RAM
The internal data RAM in the W78E058B is 512 bytes. It is divided into two banks: 256 bytes of
scratchpad RAM and 256 bytes of AUX-RAM. These RAMs are addressed by different ways.
y
RAM 0H − 7FH can be addressed directly and indirectly as the same as in 8051. Address pointers
are R0 and R1 of the selected register bank.
y
RAM 80H − FFH can only be addressed indirectly as the same as in 8051. Address pointers are
R0, R1 of the selected registers bank.
y
AUX-RAM 0H − FFH is addressed indirectly as the same way to access external data memory
with the MOVX instruction. Address pointer are R0 and R1 of the selected register bank and
DPTR register. An access to external data memory locations higher than FFH will be performed
with the MOVX instruction in the same way as in the 8051. The AUX-RAM is disable after a reset.
Setting the bit 4 in CHPCON register will enable the access to AUX-RAM. When AUX-RAM is
enabled the instructions of "MOVX @Ri" will always access to on-chip AUX-RAM. When executing
from internal program memory, an access to AUX-RAM will not affect the Ports P0, P2, WR and
RD .
Example,
CHPENR
REG
F6H
CHPCON
BFH
REG
MOV
CHPENR, #87H
MOV
CHPENR, #59H
ORL
CHPCON, #00010000B ; enable AUX-RAM
MOV
CHPENR, #00H
MOV
R0, #12H
MOV
A, #34H
MOVX
@R0, A
5.2
; Write 34h data to 12h address.
Timers 0, 1 and 2
Timers 0, 1, and 2 each consist of two 8-bit data registers. These are called TL0 and TH0 for Timer 0,
TL1 and TH1 for Timer 1, and TL2 and TH2 for Timer 2. The TCON and TMOD registers provide
control functions for timers 0, 1. The T2CON register provides control functions for Timer 2. RCAP2H
and RCAP2L are used as reload/capture registers for Timer 2. The operations of Timer 0 and Timer 1
are the same as in the W78C51. Timer 2 is a 16-bit timer/counter that is configured and controlled by
the T2CON register. Like Timers 0 and 1, Timer 2 can operate as either an external event counter or
as an internal timer, depending on the setting of bit C/T2 in T2CON. Timer 2 has three operating
modes: capture, auto-reload, and baud rate generator. The clock speed at capture or auto-reload
mode is the same as that of Timers 0 and 1.
-6-
W78E58B/W78E058B
5.3
Clock
The W78E058B is designed with either a crystal oscillator or an external clock. Internally, the clock is
divided by two before it is used by default. This makes the W78E058B relatively insensitive to duty
cycle variations in the clock.
5.4
Crystal Oscillator
The W78E058B incorporates a built-in crystal oscillator. To make the oscillator work, a crystal must be
connected across pins XTAL1 and XTAL2. In addition, a load capacitor must be connected from each
pin to ground.
5.5
External Clock
An external clock should be connected to pin XTAL1. Pin XTAL2 should be left unconnected. The
XTAL1 input is a CMOS-type input, as required by the crystal oscillator.
5.6
Power Management
Idle Mode
Setting the IDL bit in the PCON register enters the idle mode. In the idle mode, the internal clock to
the processor is stopped. The peripherals and the interrupt logic continue to be clocked. The
processor will exit idle mode when either an interrupt or a reset occurs.
Power-down Mode
When the PD bit in the PCON register is set, the processor enters the power-down mode. In this
mode all of the clocks are stopped, including the oscillator. To exit from power-down mode is by a
hardware reset or external interrupts INT0 to INT1 when enabled and set to level triggered.
5.7
Reduce EMI Emission
The W78E058B allows user to diminish the gain of on-chip oscillator amplifier by using programmer to
clear the B7 bit of security register. Once B7 is set to 0, a half of gain will be decreased. Care must be
taken if user attempts to diminish the gain of oscillator amplifier, reducing a half of gain may affect the
external crystal operating improperly at high frequency. The value of C1 and C2 may need some
adjustment while running at lower gain.
5.8
Reset
The external RESET signal is sampled at S5P2. To take effect, it must be held high for at least two
machine cycles while the oscillator is running. An internal trigger circuit in the reset line is used to
deglitch the reset line when the W78E058B is used with an external RC network. The reset logic also
has a special glitch removal circuit that ignores glitches on the reset line. During reset, the ports are
initialized to FFH, the stack pointer to 07H, PCON (with the exception of bit 4) to 00H, and all of the
other SFR registers except SBUF to 00H. SBUF is not reset.
-7-
Publication Release Date: December 4, 2006
Revision A8
W78E58B/W78E058B
W78E058B Special Function Registers (SFRs) and Reset Values
FF
F8
F0
+B
CHPENR
00000000
00000000
F7
E8
EF
+ACC
E0
E7
00000000
+P4
D8
DF
xxxx1111
+PSW
D0
D7
00000000
C8
+T2CON
RCAP2L
00000000
00000000 00000000 00000000 00000000
XICON
C0
P4CONA
00000000
B8
RCAP2H
TL2
P4CONB
SFRAL
98
90
88
80
SFRCN
CHPCON
00000000
0xx00000
+IE
00000000
+P2
11111111
+SCON
00000000
+P1
11111111
+TCON
00000000
+P0
11111111
A0
SFRFD
+IP
P43AL
00000000
A8
SFRAH
CF
00000000 00000000 00000000 00000000 00000000 00000000
+P3
B0
TH2
P43AH
P42AH
00000000
BF
B7
00000000 00000000
P42AL
00000000
C7
P2ECON
0000xx00
AF
A7
SBUF
xxxxxxxx
TMOD
00000000
SP
00000111
9F
TL0
00000000
DPL
00000000
TL1
00000000
DPH
00000000
P41AL
00000000
TH0
00000000
P40AL
00000000
P41AH
00000000
TH1
00000000
P40AH
00000000
Notes:
1.The SFRs marked with a plus sign(+) are both byte- and bit-addressable.
2. The text of SFR with bold type characters are extension function registers.
-8-
97
8F
PCON
00110000
87
W78E58B/W78E058B
5.9
Port 4
Port 4, address D8H, is a 4-bit multipurpose programmable I/O port. Each bit can be configured
individually by software. The Port 4 has four different operation modes.
Mode 0: P4.0 − P4.3 is a bi-directional I/O port which is same as port 1. P4.2 and P4.3 also serve as
external interrupt INT3 and INT2 if enabled.
Mode 1: P4.0 − P4.3 are read strobe signals that are synchronized with RD signal at specified
addresses. These signals can be used as chip-select signals for external peripherals.
Mode 2: P4.0 − P4.3 are write strobe signals that are synchronized with WR signal at specified
addresses. These signals can be used as chip-select signals for external peripherals.
Mode 3: P4.0 − P4.3 are read/write strobe signals that are synchronized with RD or WR signal at
specified addresses. These signals can be used as chip-select signals for external
peripherals.
When Port 4 is configured with the feature of chip-select signals, the chip-select signal address range
depends on the contents of the SFR P4xAH, P4xAL, P4CONA and P4CONB. The registers P4xAH
and P4xAL contain the 16-bit base address of P4.x. The registers P4CONA and P4CONB contain the
control bits to configure the Port 4 operation mode.
5.10 INT2 / INT3
Two additional external interrupts, INT2 and INT3 , whose functions are similar to those of external
interrupt 0 and 1 in the standard 80C52. The functions/status of these interrupts are
determined/shown by the bits in the XICON (External Interrupt Control) register. The XICON register is
bit-addressable but is not a standard register in the standard 80C52. Its address is at 0C0H. To
set/clear bits in the XICON register, one can use the "SETB ( CLR ) bit" instruction. For example,
"SETB 0C2H" sets the EX2 bit of XICON.
XICON - external interrupt control (C0H)
PX3
EX3
IE3
IT3
PX2
EX2
IE2
IT2
PX3: External interrupt 3 priority high if set
EX3: External interrupt 3 enable if set
IE3: If IT3 = 1, IE3 is set/cleared automatically by hardware when interrupt is detected/serviced
IT3: External interrupt 3 is falling-edge/low-level triggered when this bit is set/cleared by software
PX2: External interrupt 2 priority high if set
EX2: External interrupt 2 enable if set
IE2: If IT2 = 1, IE2 is set/cleared automatically by hardware when interrupt is detected/serviced
IT2: External interrupt 2 is falling-edge/low-level triggered when this bit is set/cleared by software
-9-
Publication Release Date: December 4, 2006
Revision A8
W78E58B/W78E058B
Eight-source interrupt information
INTERRUPT
SOURCE
VECTOR
ADDRESS
POLLING
SEQUENCE WITHIN
PRIORITY LEVEL
ENABLE
REQUIRED
SETTINGS
INTERRUPT
TYPE
EDGE/LEVEL
External Interrupt 0
03H
0 (highest)
IE.0
TCON.0
Timer/Counter 0
0BH
1
IE.1
-
External Interrupt 1
13H
2
IE.2
TCON.2
Timer/Counter 1
1BH
3
IE.3
-
Serial Port
23H
4
IE.4
-
Timer/Counter 2
2BH
5
IE.5
-
External Interrupt 2
33H
6
XICON.2
XICON.0
External Interrupt 3
3BH
7 (lowest)
XICON.6
XICON.3
P4CONB (C3H)
BIT
NAME
FUNCTION
00: Mode 0. P4.3 is a general purpose I/O port which is the same as Port1.
01: Mode 1. P4.3 is a Read Strobe signal for chip select purpose. The address
range depends on the SFR P43AH, P43AL, P43CMP1 and P43CMP0.
7, 6
P43FUN1
P43FUN0
10: Mode 2. P4.3 is a Write Strobe signal for chip select purpose. The address
range depends on the SFR P43AH, P43AL, P43CMP1 and P43CMP0.
11: Mode 3. P4.3 is a Read/Write Strobe signal for chip select purpose. The
address range depends on the SFR P43AH, P43AL, P43CMP1, and
P43CMP0.
Chip-select signals address comparison:
00: Compare the full address (16 bits length) with the base address register
P43AH, P43AL.
5, 4
P43CMP1
P43CMP0
01: Compare the 15 high bits (A15 − A1) of address bus with the base address
register P43AH, P43AL.
10: Compare the 14 high bits (A15 − A2) of address bus with the base address
register P43AH, P43AL.
11: Compare the 8 high bits (A15 − A8) of address bus with the base address
register P43AH, P43AL.
3, 2
1, 0
P42FUN1
P42FUN0
P42CMP1
P42CMP0
The P4.2 function control bits which are the similar definition as P43FUN1,
P43FUN0.
The P4.2 address comparator length control bits which are the similar definition
as P43CMP1, P43CMP0.
- 10 -
W78E58B/W78E058B
P4CONA (C2H)
BIT
7, 6
5, 4
3, 2
1, 0
NAME
FUNCTION
P41FUN1
The P4.1 function control bits which are the similar definition as P43FUN1,
P43FUN0.
P41FUN0
P41CMP1
P41CMP0
P40FUN1
P40FUN0
P40CMP1
P40CMP0
The P4.1 address comparator length control bits which are the similar definition
as P43CMP1, P43CMP0.
The P4.0 function control bits which are the similar definition as P43FUN1,
P43FUN0.
The P4.0 address comparator length control bits which are the similar definition
as P43CMP1, P43CMP0.
P2ECON (AEH)
BIT
NAME
FUNCTION
The active polarity of P4.3 when pin P4.3 is defined as read and/or write strobe
signal.
7
P43CSINV
1: P4.3 is active high when pin P4.3 is defined as read and/or write strobe
signal.
0: P4.3 is active low when pin P4.3 is defined as read and/or write strobe
signal.
6
P42CSINV The similarity definition as P43SINV.
5
P41CSINV The similarity definition as P43SINV.
4
P40CSINV The similarity definition as P43SINV.
3
-
Reserve
2
-
Reserve
1
-
0
0
-
0
5.11 Port 4 Base Address Registers
P40AH, P40AL
The Base address register for comparator of P4.0. P40AH contains the high-order byte of address,
P40AL contains the low-order byte of address.
P41AH, P41AL
The Base address register for comparator of P4.1. P41AH contains the high-order byte of address,
P41AL contains the low-order byte of address.
- 11 -
Publication Release Date: December 4, 2006
Revision A8
W78E58B/W78E058B
P42AH, P42AL
The Base address register for comparator of P4.2. P42AH contains the high-order byte of address,
P42AL contains the low-order byte of address.
P43AH, P43AL
The Base address register for comparator of P4.3. P43AH contains the high-order byte of address,
P43AL contains the low-order byte of address.
P4 (D8H)
BIT
NAME
FUNCTION
7
-
Reserve
6
-
Reserve
5
-
Reserve
4
-
Reserve
3
P43
Port 4 Data bit which outputs to pin P4.3 at mode 0.
2
P42
Port 4 Data bit. which outputs to pin P4.2 at mode 0.
1
P41
Port 4 Data bit. which outputs to pin P4.1at mode 0.
0
P40
Port 4 Data bit which outputs to pin P4.0 at mode 0.
Here is an example to program the P4.0 as a write strobe signal at the I/O port address 1234H
−1237H and positive polarity, and P4.1 − P4.3 are used as general I/O ports.
MOV P40AH, #12H
MOV P40AL, #34H
MOV P4CONA, #00001010B
MOV P4CONB, #00H
MOV P2ECON, #10H
; Base I/O address 1234H for P4.0
; P4.0 a write strobe signal and address line A0 and A1 are masked.
; P4.1 − P4.3 as general I/O port which are the same as PORT1
; Write the P40SINV = 1 to inverse the P4.0 write strobe polarity
; default is negative.
Then any instruction MOVX @DPTR, A (with DPTR = 1234H − 1237H) will generate the positive
polarity write strobe signal at pin P4.0. And the instruction MOV P4, #XX will output the bit3 to bit1 of
data #XX to pin P4.3 − P4.1.
- 12 -
W78E58B/W78E058B
P4xCSINV
P4 REGISTER
P4.x
DATA I/O
RD_CS
MUX 4->1
WR_CS
READ
WRITE
RD/WR_CS
PIN
P4.x
ADDRESS BUS
P4xFUN0
P4xFUN1
EQUAL
REGISTER
P4xAL
P4xAH
Bit Length
Selectable
comparator
P4.x INPUT DATA BUS
REGISTER
P4xCMP0
P4xCMP1
5.12 In-System Programming (ISP) Mode
The W78E058B equips one 32K byte of main ROM bank for application program (called APROM) and
one 4K byte of auxiliary ROM bank for loader program (called LDROM). In the normal operation, the
microcontroller executes the code in the APROM. If the content of APROM needs to be modified, the
W78E058B allows user to activate the In-System Programming (ISP) mode by setting the CHPCON
register. The CHPCON is read-only by default, software must write two specific values 87H,
then 59H sequentially to the CHPENR register to enable the CHPCON write attribute. Writing
CHPENR register with the values except 87H and 59H will close CHPCON register write
attribute. The W78E058B achieves all in-system programming operations including enter/exit ISP
Mode, program, erase, read ... etc, during device in the idle mode. Setting the bit CHPCON.0 the
device will enter in-system programming mode after a wake-up from idle mode. Because device
needs proper time to complete the ISP operations before awaken from idle mode, software may use
timer interrupt to control the duration for device wake-up from idle mode. To perform ISP operation for
revising contents of APROM, software located at APROM setting the CHPCON register then enter idle
mode, after awaken from idle mode the device executes the corresponding interrupt service routine in
LDROM. Because the device will clear the program counter while switching from APROM to LDROM,
the first execution of RETI instruction in interrupt service routine will jump to 00H at LDROM area. The
device offers a software reset for switching back to APROM while the content of APROM has been
updated completely. Setting CHPCON register bit 0, 1 and 7 to logic-1 will result a software reset
to reset the CPU. The software reset serves as a external reset. This in-system programming feature
makes the job easy and efficient in which the application needs to update firmware frequently. In some
- 13 -
Publication Release Date: December 4, 2006
Revision A8
W78E58B/W78E058B
applications, the in-system programming feature make it possible to easily update the system
firmware without opening the chassis.
SFRAH, SFRAL: The objective address of on-chip ROM in the in-system programming mode.
SFRAH contains the high-order byte of address, SFRAL contains the low-order
byte of address.
SFRFD: The programming data for on-chip ROM in programming mode.
SFRCN: The control byte of on-chip ROM programming mode.
SFRCN (C7)
BIT
NAME
7
-
FUNCTION
Reserve.
On-chip ROM bank select for in-system programming.
6
WFWIN
0: 32K bytes ROM bank is selected as destination for re-programming.
1: 4K bytes ROM bank is selected as destination for re-programming.
5
OEN
ROM output enable.
4
CEN
ROM chip enable.
3, 2, 1, 0
CTRL [3:0] The flash control signals
MODE
WFWIN
CTRL<3:0>
OEN
CEN
SFRAH, SFRAL
SFRFD
Erase 32KB APROM
0
0010
1
0
X
X
Program 32KB APROM
0
0001
1
0
Address in
Data in
Read 32KB APROM
0
0000
0
0
Address in
Data out
Erase 4KB LDROM
1
0010
1
0
X
X
Program 4KB LDROM
1
0001
1
0
Address in
Data in
Read 4KB LDROM
1
0000
0
0
Address in
Data out
- 14 -
W78E58B/W78E058B
5.13 In-System Programming Control Register (CHPCON)
CHPCON (BFH)
BIT
7
NAME
FUNCTION
When this bit is set to 1, and both FBOOTSL and FPROGEN are set to 1. It will
SWRESET enforce microcontroller reset to initial condition just like power on reset. This
(F04KMODE) action will re-boot the microcontroller and start to normal operation. To read this
bit in logic-1 can determine that the F04KBOOT mode is running.
6
-
Reserve.
5
-
Reserve.
4
ENAUXRAM
3
0
Must set to 0.
2
0
Must set to 0.
1: Enable on-chip AUX-RAM.
0: Disable the on-chip AUX-RAM
The Program Location Select.
1
FBOOTSL
0: The Loader Program locates at the 32 KB APROM. 4KB LDROM is
destination for re-programming.
1: The Loader Program locates at the 4 KB memory bank. 32KB APROM is
destination for re-programming.
ROM Programming Enable.
0
1: enable. The microcontroller enter the in-system programming mode after
entering the idle mode and wake-up from interrupt. During in-system
FPROGEN programming mode, the operation of erase, program and read are achieve
when device enters idle mode.
0: disable. The on-chip flash memory is read-only. In-system
is disabled.
programmability
5.14 F04KBOOT Mode (Boot From LDROM)
By default, the W78E058B boots from APROM program after a power on reset. On some occasions,
user can force the W78E058B to boot from the LDROM program via following settings. The possible
situation that you need to enter F04KBOOT mode when the APROM program can not run properly
and device can not jump back to LDROM to execute in-system programming function. Then you can
use this F04KBOOT mode to force the W78E058B jumps to LDROM and executes in-system
programming procedure. When you design your system, you may reserve the pins P2.6, P2.7 to
switches or jumpers. For example in a CD-ROM system, you can connect the P2.6 and P2.7 to PLAY
and EJECT buttons on the panel. When the APROM program fails to execute the normal application
program. User can press both two buttons at the same time and then turn on the power of the
personal computer to force the W78E058B to enter the F04KBOOT mode. After power on of personal
computer, you can release both buttons and finish the in-system programming procedure to update
the APROM code. In application system design, user must take care of the P2, P3, ALE, EA and
PSEN pin value at reset to prevent from accidentally activating the programming mode or F04KBOOT
mode.
- 15 -
Publication Release Date: December 4, 2006
Revision A8
W78E58B/W78E058B
F04KBOOT Mode
P4.3
P2.7
P2.6
MODE
X
L
L
FO4KBOOT
L
X
X
FO4KBOOT
The Reset Timing For Entering
F04KBOOT Mode
P2.7
Hi-Z
P2.6
Hi-Z
RST
30 mS
10 mS
- 16 -
W78E58B/W78E058B
The Algorithm of In-System Programming
Part 1:32KB APROM
procedure of entering
In-System Programming Mode
START
Enter In-System
Programming Mode ?
(conditions depend on
user's application)
No
Yes
Setting control registers
MOV CHPENR,#87H
MOV CHPENR,#59H
MOV CHPCON,#03H
Execute the normal application
program
Setting Timer (about 1.5 us)
and enable timer interrupt
END
Start Timer and enter idle Mode.
(CPU will be wakened from idle mode
by timer interrupt, then enter In-System
Programming mode)
CPU will be wakened by interrupt and
re-boot from 4KB LDROM to execute
the loader program.
Go
- 17 -
Publication Release Date: December 4, 2006
Revision A8
W78E58B/W78E058B
Part 2: 4KB LDROM
Go
Procedure of Updating
the 32KB APROM
Timer Interrupt Service Routine:
Stop Timer & disable interrupt
PGM
Yes
Yes
Is F04KBOOT Mode?
(CHPCON.7=1)
End of Programming ?
No
No
Reset the CHPCON Register:
MOV CHPENR,#87H
MOV CHPENR,#59H
MOV CHPCON,#03H
Setting Timer and enable Timer
interrupt for wake-up .
(50us for program operation)
Yes
Is currently in the
F04KBOOT Mode ?
No
Get the parameters of new code
Setting Timer and enable Timer
interrupt for wake-up .
(15 ms for erasing operation)
Setting erase operation mode:
MOV SFRCN,#22H
(Erase 32KB APROM)
Start Timer and enter IDLE
Mode.
(Erasing...)
(Address and data bytes)
through I/O ports, UART or
other interfaces.
Software reset CPU and
re-boot from the 32KB
APROM.
MOV CHPENR,#87H
MOV CHPENR,#59H
MOV CHPCON,#83H
Setting control registers for
programming:
Hardware Reset
to re-boot from
new 32 KB APROM.
(S/W reset is
invalid in F04KBOOT
Mode)
MOV SFRAH,#ADDRESS_H
MOV SFRAL,#ADDRESS_L
MOV SFRFD,#DATA
MOV SFRCN,#21H
End of erase
operation. CPU will
be wakened by Timer
interrupt.
END
Executing new code
from address
00H in the 32KB APROM.
PGM
- 18 -
W78E58B/W78E058B
6. SECURITY
During the on-chip ROM programming mode, the ROM can be programmed and verified repeatedly.
Until the code inside the ROM is confirmed OK, the code can be protected. The protection of ROM
and those operations on it are described below.
The W78E058B has a Security Register that can be accessed in programming mode. Those bits of
the Security Registers can not be changed once they have been programmed from high to low. They
can only be reset through erase-all operation. The Security Register is located at the 0FFFFH of the
LDROM space.
B7 Reserved
B2 B1 B0
4KB On-chip ROM
Program Memory
LDROM
Security Bits
0000h
32KB On-chip ROM
Program Memory
0FFFh
B0: Lock bit, logic 0: active
B1: MOVC inhibit,
logic 0: the MOVC instruction in external memory
cannot access the code in internal memory.
logic 1: no restriction.
B2: Encryption
logic 0: the encryption logic enable
logic 1: the encryption logic disable
B07: Osillator Control
logic 0: 1/2 gain
logic 1: Full gain
Default 1 for all security bits.
Reserved bits must be kept in logic 1.
Reserved
Reserved
Security Register
APROM
7FFFh
FFFFh
Special Setting Register
6.1
Lock Bit
This bit is used to protect the customer's program code in the W78E058B. It may be set after the
programmer finishes the programming and verifies sequence. Once this bit is set to logic 0, both the
ROM data and Security Register can not be accessed again.
6.2
MOVC Inhibit
This bit is used to restrict the accessible region of the MOVC instruction. It can prevent the MOVC
instruction in external program memory from reading the internal program code. When this bit is set to
logic 0, a MOVC instruction in external program memory space will be able to access code only in the
external memory, not in the internal memory. A MOVC instruction in internal program memory space
will always be able to access the ROM data in both internal and external memory. If this bit is logic 1,
there are no restrictions on the MOVC instruction.
- 19 -
Publication Release Date: December 4, 2006
Revision A8
W78E58B/W78E058B
6.3
Encryption
This bit is used to enable/disable the encryption logic for code protection. Once encryption feature is
enabled, the data presented on port 0 will be encoded via encryption logic. Only whole chip erase will
reset this bit.
6.4
Oscillator Control
W78E058B/E516 allow user to diminish the gain of on-chip oscillator amplifier by using programmer to
set the bit B7 of security register. Once B7 is set to 0, a half of gain will be decreased. Care must be
taken if user attempts to diminish the gain of oscillator amplifier, reducing a half of gain may
improperly affect the external crystal operation at high frequency above 24 MHz. The value of R and
C1, C2 may need some adjustment while running at lower gain.
- 20 -
W78E58B/W78E058B
7. ELECTRICAL CHARACTERISTICS
7.1
Absolute Maximum Ratings
PARAMETER
SYMBOL
MIN.
MAX.
UNIT
VDD − VSS
-0.3
+6.0
V
Input Voltage
VIN
VSS -0.3
VDD +0.3
V
Operating Temperature
TA
0
70
°C
Storage Temperature
TST
-55
+150
°C
DC Power Supply
Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely affect the life and reliability
of the device.
7.2
D.C. Characteristics
(VDD−VSS = 5V ±10%, TA = 25° C, Fosc = 20 MHz, unless otherwise specified.)
PARAMETER
SPECIFICATION
SYM.
MIN.
MAX.
UNIT
TEST CONDITIONS
Operating Voltage
VDD
4.5
5.5
V
RST = 1, P0 = VDD
Operating Current
IDD
-
20
mA
No load
VDD = 5.5V
IIDLE
-
6
mA
Idle mode
VDD = 5.5V
IPWDN
-
50
μA
Power-down mode
VDD = 5.5V
Input Current
P1, P2, P3, P4
IIN1
-50
+10
μA
VDD = 5.5V
VIN = 0V or VDD
Input Current
RST
IIN2
-10
+300
μA
VDD = 5.5V
0V < VIN < VDD
Input Leakage Current
P0, EA
ILK
-10
+10
μA
VDD = 5.5V
0V < VIN < VDD
ITL[*4]
-500
-
μA
VDD = 5.5V
VIN = 2.0V
VIL1
0
0.8
V
VDD = 4.5V
V IL2
0
0.8
V
VDD = 4.5V
Idle Current
Power Down Current
Logic 1 to 0 Transition Current
P1, P2, P3, P4
Input Low Voltage
P0, P1, P2, P3, P4, EA
Input Low Voltage
RST
- 21 -
Publication Release Date: December 4, 2006
Revision A8
W78E58B/W78E058B
D.C. Characteristics, continued
PARAMETER
Input Low Voltage
XTAL1[*4]
Input High Voltage
P0, P1, P2, P3, P4, EA
Input High Voltage
RST
Input High Voltage
XTAL1[*4]
Output Low Voltage
P1, P2, P3, P4
SPECIFICATION
SYM.
TEST CONDITIONS
MIN.
MAX.
UNIT
V IL3
0
0.8
V
VDD = 4.5V
VIH1
2.4
VDD +0.2
V
VDD = 5.5V
VIH2
3.5
VDD +0.2
V
VDD = 5.5V
VIH3
3.5
VDD +0.2
V
VDD = 5.5V
VOL1
-
0.45
V
VOL2
-
0.45
V
Isk1
4
12
mA
Isk2
10
20
mA
VOH1
2.4
-
V
VOH2
2.4
-
V
Isr1
-120
-250
μA
Isr2
-8
-20
mA
Output Low Voltage
P0, ALE, PSEN
[*3]
Sink current
P1, P3, P4
Sink current
P0, P2, ALE, PSEN
Output High Voltage
P1, P2, P3, P4
Output High Voltage
P0, ALE, PSEN
[*3]
Source Current
P1, P2, P3, P4
Source Current
P0, P2, ALE, PSEN
VDD = 4.5V
IOL = +2 mA
VDD = 4.5V
IOL = +4 mA
VDD = 4.5V
VIN = 0.45V
VDD = 4.5V
VIN = 0.45V
VDD = 4.5V
IOH = -100 μA
VDD = 4.5V
IOH = -400 μA
VDD = 4.5V
VIN = 2.4V
VDD = 4.5V
VIN = 2.4V
Notes:
*1. RST pin is a Schmitt trigger input.
*2. P0, ALE and PSEN are tested in the external access mode.
*3. XTAL1 is a CMOS input.
*4. Pins of P1, P2, P3, P4 can source a transition current when they are being externally driven from 1 to 0.
- 22 -
W78E58B/W78E058B
7.3
A.C. Characteristics
The AC specifications are a function of the particular process used to manufacture the part, the
ratings of the I/O buffers, the capacitive load, and the internal routing capacitance. Most of the
specifications can be expressed in terms of multiple input clock periods (TCP), and actual parts will
usually experience less than a ±20 nS variation. The numbers below represent the performance
expected from a 0.6 micron CMOS process when using 2 and 4 mA output buffers.
7.3.1
Clock Input Waveform
XTAL1
T CH
T CL
F OP,
PARAMETER
TCP
SYMBOL
MIN.
TYP.
MAX.
UNIT
NOTES
Operating Speed
FOP
0
-
40
MHz
1
Clock Period
TCP
25
-
-
nS
2
Clock High
TCH
10
-
-
nS
3
Clock Low
TCL
10
-
-
nS
3
MIN.
TYP.
MAX.
UNIT
NOTES
Notes:
1. The clock may be stopped indefinitely in either state.
2. The TCP specification is used as a reference in other specifications.
3. There are no duty cycle requirements on the XTAL1 input.
7.3.2
Program Fetch Cycle
PARAMETER
SYMBOL
Address Valid to ALE Low
TAAS
1 TCP-Δ
-
-
nS
4
Address Hold from ALE Low
TAAH
1 TCP-Δ
-
-
nS
1, 4
ALE Low to PSEN Low
TAPL
1 TCP-Δ
-
-
nS
4
PSEN Low to Data Valid
TPDA
-
-
2 TCP
nS
2
Data Hold after PSEN High
TPDH
0
-
1 TCP
nS
3
Data Float after PSEN High
ALE Pulse Width
TPDZ
0
-
1 TCP
nS
TALW
2 TCP-Δ
2 TCP
-
nS
4
PSEN Pulse Width
TPSW
3 TCP-Δ
3 TCP
-
nS
4
Notes:
1. P0.0 − P0.7, P2.0 − P2.7 remain stable throughout entire memory cycle.
2. Memory access time is 3 TCP.
3. Data have been latched internally prior to PSEN going high.
4. "Δ" (due to buffer driving delay and wire loading) is 20 nS.
- 23 -
Publication Release Date: December 4, 2006
Revision A8
W78E58B/W78E058B
7.3.3
Data Read Cycle
PARAMETER
SYMBOL
MIN.
TYP.
MAX.
UNIT
NOTES
ALE Low to RD Low
TDAR
3 TCP-Δ
-
3 TCP+Δ
nS
1, 2
RD Low to Data Valid
TDDA
-
-
4 TCP
nS
1
Data Hold from RD High
TDDH
0
-
2 TCP
nS
Data Float from RD High
TDDZ
0
-
2 TCP
nS
RD Pulse Width
TDRD
6 TCP-Δ
6 TCP
-
nS
2
Notes:
1. Data memory access time is 8 TCP.
2. "Δ" (due to buffer driving delay and wire loading) is 20 nS.
7.3.4
Data Write Cycle
PARAMETER
SYMBOL
MIN.
TYP.
MAX.
UNIT
ALE Low to WR Low
TDAW
3 TCP-Δ
-
3 TCP+Δ
nS
Data Valid to WR Low
TDAD
1 TCP-Δ
-
-
nS
Data Hold from WR High
TDWD
1 TCP-Δ
-
-
nS
WR Pulse Width
TDWR
6 TCP-Δ
6 TCP
-
nS
Note: "Δ" (due to buffer driving delay and wire loading) is 20 nS.
7.3.5
Port Access Cycle
PARAMETER
SYMBOL
MIN.
TYP.
MAX.
UNIT
Port Input Setup to ALE Low
TPDS
1 TCP
-
-
nS
Port Input Hold from ALE Low
TPDH
0
-
-
nS
Port Output to ALE
TPDA
1 TCP
-
-
nS
Note: Ports are read during S5P2, and output data becomes available at the end of S6P2. The timing data are referenced to
ALE, since it provides a convenient reference.
- 24 -
W78E58B/W78E058B
8. TIMING WAVEFORMS
8.1
Program Fetch Cycle
S1
S2
S3
S4
S5
S6
S1
S2
S3
S4
S5
S6
XTAL1
TALW
ALE
TAPL
PSEN
TPSW
TAAS
PORT 2
TPDA
TAAH
TPDH, TPDZ
PORT 0
Code
8.2
A0-A7
Data
A0-A7
Code
A0-A7
Data
A0-A7
Data Read Cycle
S4
S5
S6
S1
S2
S3
S4
S5
S6
S1
S2
S3
XTAL1
ALE
PSEN
PORT 2
A8-A15
DATA
A0-A7
PORT 0
T DAR
T DDA
T DDH, T DDZ
RD
T DRD
- 25 -
Publication Release Date: December 4, 2006
Revision A8
W78E58B/W78E058B
8.3
Data Write Cycle
S4
S5
S6
S1
S2
S3
S4
S5
S6
S1
S2
XTAL1
ALE
PSEN
PORT 2
PORT 0
A8-A15
A0-A7
DATA OUT
WR
T DWR
T DAW
8.4
T DWD
TDAD
Port Access Cycle
S5
S6
S1
XTAL1
ALE
TPDS
T PDA
TPDH
DATA OUT
PORT
INPUT
SAMPLE
- 26 -
S3
W78E58B/W78E058B
9. TYPICAL APPLICATION CIRCUITS
9.1
Expanded External Program Memory and Crystal
VDD
31
19
XTAL1
R 18
XTAL2
10 u
CRYSTAL
8.2 K
9
C1
EA
C2
RST
INT0
12
13
14
15
INT1
T0
T1
1
2
3
4
5
6
7
8
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
39
38
37
36
35
34
33
32
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
AD0 3
AD1 4
AD2 7
AD3 8
AD4 13
AD5 14
AD6 17
AD7 18
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
P2.7
21
22
23
24
25
26
27
28
A8
A9
A10
A11
A12
A13
A14
A15
GND 1
RD
WR
PSEN
ALE
TXD
RXD
17
16
29
30
11
10
D0
D1
D2
D3
D4
D5
D6
D7
Q0
Q1
Q2
Q3
Q4
Q5
Q6
Q7
2
5
6
9
12
15
16
19
A0
A1
A2
A3
A4
A5
A6
A7
OC
11 G
74LS373
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
10
9
8
7
6
5
4
3
25
24
21
23
2
26
27
1
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
O0
O1
O2
O3
O4
O5
O6
O7
11
12
13
15
16
17
18
19
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
GND 20 CE
22
OE
27512
W78E58B/W78E058B
Figure A
CRYSTAL
C1
C2
R
6 MHz
47P
47P
-
16 MHz
30P
30P
-
24 MHz
15P
10P
-
40MHz
5P
5P
6.8K
Above table shows the reference values for crystal applications.
Notes:
1. C1, C2, R components refer to Figure A
2. Crystal layout must get close to XTAL1 and XTAL2 pins on user's application board.
- 27 -
Publication Release Date: December 4, 2006
Revision A8
W78E58B/W78E058B
9.2
Expanded External Data Memory and Oscillator
VDD
VDD
31
19
10 u
8.2 K
OSCILLATOR
EA
XTAL1
18
XTAL2
9
RST
12
13
14
15
1
2
3
4
5
6
7
8
INT0
INT1
T0
T1
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
39
38
37
36
35
34
33
32
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
P2.7
21
22
23
24
25
26
27
28
A8
A9
A10
A11
A12
A13
A14
RD
WR
17
16
29
30
11
10
PSEN
ALE
TXD
RXD
AD0 3
AD1 4
AD2 7
AD3 8
AD4 13
AD5 14
AD6 17
AD7 18
D0
D1
D2
D3
D4
D5
D6
D7
Q0
Q1
Q2
Q3
Q4
Q5
Q6
Q7
GND 1
OC
11 G
74LS373
2
5
6
9
12
15
16
19
A0
A1
A2
A3
A4
A5
A6
A7
10
9
8
7
6
5
4
3
25
24
21
23
2
26
1
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
GND 20
22
27
CE
OE
WR
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
20256
W78E58B/W78E058B
Figure B
- 28 -
D0
D1
D2
D3
D4
D5
D6
D7
11
12
13
15
16
17
18
19
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
W78E58B/W78E058B
10. PACKAGE DIMENSIONS
10.1 40-pin DIP
Symbol
A
A1
A2
B
B1
c
D
E
E1
e1
L
D
40
21
E1
a
eA
S
20
1
Dimension in inchDimension in mm
Min. Nom. Max. Min. Nom. Max.
5.334
0.210
0.010
0.254
0.150 0.155 0.160
3.81
0.016 0.018 0.022
0.406 0.457 0.559
0.048 0.050 0.054
1.219 1.27
0.008 0.010 0.014
0.203 0.254 0.356
2.055 2.070
52.20 52.58
3.937 4.064
1.372
0.590 0.600 0.610 14.986 15.24 15.494
0.540 0.545 0.550 13.72 13.84 13.97
0.090 0.100 0.110 2.286
2.54
0.120 0.130 0.140 3.048
3.302 3.556
0
15
2.794
0
15
0.630 0.650 0.670 16.00 16.51 17.01
0.090
2.286
Notes:
E
S
c
A A2
A1
Base Plane
Seating Plane
L
B
e1
eA
a
B1
1. Dimension D Max. & S include mold flash or
tie bar burrs.
2. Dimension E1 does not include interlead flash.
3. Dimension D & E1 include mold mismatch and
are determined at the. mold parting line.
4. Dimension B1 does not include dambar
protrusion/intrusion.
5. Controlling dimension: Inches.
6. General appearance spec. should be based on
final visual inspection spec.
10.2 44-pin PLCC
HD
D
6
1
44
40
Symbol
7
39
E
17
HE
GE
29
18
28
c
A
A1
A2
b1
b
c
D
E
e
GD
GE
HD
HE
L
y
Dimension in inch Dimension in mm
Min. Nom. Max. Min. Nom. Max.
0.185
0.020
4.699
0.508
0.145 0.150 0.155 3.683 3.81 3.937
0.026 0.028 0.032
0.66
0.711 0.813
0.016 0.018 0.022 0.406 0.457 0.559
0.008 0.010 0.014 0.203 0.254 0.356
0.648 0.653 0.658 16.46 16.59 16.71
0.648 0.653 0.658 16.46 16.59 16.71
0.050 BSC
1.27
BSC
0.590 0.610 0.630 14.99 15.49 16.00
0.590 0.610 0.630 14.99 15.49 16.00
0.680 0.690 0.700 17.27 17.53 17.78
0.680 0.690 0.700 17.27 17.53 17.78
0.090 0.100 0.110 2.296
2.54 2.794
0.004
0.10
L
Notes:
A2 A
1. Dimension D & E do not include interlead
flash.
2. Dimension b1 does not include dambar
protrusion/intrusion.
3. Controlling dimension: Inches
4. General appearance spec. should be based
on final visual inspection spec.
θ
e
b
b1
Seating Plane
A1
y
GD
- 29 -
Publication Release Date: December 4, 2006
Revision A8
W78E58B/W78E058B
10.3 44-pin PQFP
HD
Dimension in inch
D
Symbol
34
44
A
A1
A2
b
c
D
E
e
HD
HE
L
L1
y
θ
33
1
E HE
11
12
e
b
22
Dimension in mm
Min. Nom. Max. Min. Nom. Max.
---
---
---
---
0.002
0.01
0.02
0.05
0.25
0.5
0.075
0.081
0.087
1.90
2.05
2.20
0.01
0.014
0.018
0.25
0.35
0.45
0.004
0.006
0.010
0.101
0.152
0.254
0.390
0.394
0.398
9.9
10.00
10.1
0.390
0.394
0.398
9.9
10.00
10.1
0.025
0.031
0.036
0.635
0.80
0.952
0.510
0.520
0.530
12.95
13.2
13.45
0.510
0.520
0.530
12.95
13.2
13.45
0.025
0.031
0.037
0.65
0.8
0.95
0.051
0.063
0.075
1.295
1.6
1.905
---
0.08
0.003
0
7
0
Notes:
1. Dimension D & E do not include interlead
flash.
2. Dimension b does not include dambar
protrusion/intrusion.
3. Controlling dimension: Millimeter
4. General appearance spec. should be based
on final visual inspection spec.
c
A2 A
Seating Plane
See Detail F
A1
y
θ
L
L1
Detail F
- 30 -
---
7
W78E58B/W78E058B
11. APPLICATION NOTES
11.1 In-system Programming Software Examples
This application note illustrates the in-system programmability of the Winbond W78E058B ROM
microcontroller. In this example, microcontroller will boot from 32KB APROM bank and waiting for a
key to enter in-system programming mode for re-programming the contents of 32KB APROM. While
entering in-system programming mode, microcontroller executes the loader program in 4KB LDROM
bank. The loader program erases the 32KB APROM then reads the new code data from external
SRAM buffer (or through other interfaces) to update the 32KB APROM.
EXAMPLE 1:
;*******************************************************************************************************************
;* Example of 32K APROM program: Program will scan the P1.0. if P1.0 = 0, enters in-system
;* programming mode for updating the content of APROM code else executes the current ROM code.
;* XTAL = 16 MHz
;*******************************************************************************************************************
.chip 8052
.RAMCHK OFF
.symbols
CHPCON
CHPENR
SFRAL
SFRAH
SFRFD
SFRCN
EQU
EQU
EQU
EQU
EQU
EQU
BFH
F6H
C4H
C5H
C6H
C7H
ORG
0H
LJMP 100H
; JUMP TO MAIN PROGRAM
;************************************************************************
;* TIMER0 SERVICE VECTOR ORG = 000BH
;************************************************************************
ORG 00BH
CLR
TR0
; TR0 = 0, STOP TIMER0
MOV
TL0, R6
MOV
TH0, R7
RETI
;************************************************************************
;* 32K APROM MAIN PROGRAM
;************************************************************************
ORG 100H
MAIN_32K:
MOV A, P1
; SCAN P1.0
ANL A, #01H
CJNE A, #01H, PROGRAM_32K; IF P1.0 = 0, ENTER IN-SYSTEM PROGRAMMING MODE
JMP NORMAL_MODE
PROGRAM_32K:
MOV CHPENR, #87H
MOV CHPENR, #59H
MOV CHPCON, #03H
; CHPENR = 87H, CHPCON REGISTER WRTE ENABLE
; CHPENR = 59H, CHPCON REGISTER WRITE ENABLE
; CHPCON = 03H, ENTER IN-SYSTEM PROGRAMMING MODE
- 31 -
Publication Release Date: December 4, 2006
Revision A8
W78E58B/W78E058B
MOV TCON, #00H
MOV IP, #00H
MOV IE, #82H
MOV R6, #F0H
MOV R7, #FFH
MOV TL0, R6
MOV TH0, R7
MOV TMOD, #01H
MOV TCON, #10H
MOV PCON, #01H
; TR = 0 TIMER0 STOP
; IP = 00H
; TIMER0 INTERRUPT ENABLE FOR WAKE-UP FROM IDLE MODE
; TL0 = F0H
; TH0 = FFH
; TMOD = 01H, SET TIMER0 A 16-BIT TIMER
; TCON = 10H, TR0 = 1, GO
; ENTER IDLE MODE FOR LAUNCHING THE IN-SYSTEM
; PROGRAMMING
;********************************************************************************
;* Normal mode 32KB APROM program: depending user's application
;********************************************************************************
NORMAL_MODE:
.
; User's application program
.
.
.
EXAMPLE 2:
;******************************************************************************************************************************
Example of 4 KB LDROM program: This loader program will erase the 32KB APROM first, then reads the new ;*
code from external SRAM and program them into 32 KB APROM bank. XTAL = 16 MHz
;*****************************************************************************************************************************
.chip 8052
.RAMCHK OFF
.symbols
CHPCON
CHPENR
SFRAL
SFRAH
SFRFD
SFRCN
ORG
LJMP
EQU
EQU
EQU
EQU
EQU
EQU
000H
100H
BFH
F6H
C4H
C5H
C6H
C7H
; JUMP TO MAIN PROGRAM
;************************************************************************
;* 1. TIMER0 SERVICE VECTOR ORG = 0BH
;************************************************************************
ORG 000BH
CLR TR0
; TR0 = 0, STOP TIMER0
MOV TL0, R6
MOV TH0, R7
RETI
;************************************************************************
;* 4KB LDROM MAIN PROGRAM
;************************************************************************
ORG 100H
- 32 -
W78E58B/W78E058B
MAIN_4K:
MOV SP, #C0H
MOV CHPENR, #87H ; CHPENR = 87H, CHPCON WRITE ENABLE.
MOV CHPENR, #59H ; CHPENR = 59H, CHPCON WRITE ENABLE.
MOV A, CHPCON
ANL A, #80H
CJNE A, #80H, UPDATE_32K ; CHECK F04KBOOT MODE ?
MOV CHPCON, #03H ; CHPCON = 03H, ENABLE IN-SYSTEM PROGRAMMING.
MOV CHPENR, #00H ; DISABLE CHPCON WRITE ATTRIBUTE
MOV TCON, #00H
MOV TMOD, #01H
MOV IP, #00H
MOV IE, #82H
MOV R6, #F0H
MOV R7, #FFH
MOV TL0, R6
MOV TH0, R7
MOV TCON, #10H
MOV PCON, #01H
UPDATE_32K:
MOV CHPENR, #00H
MOV TCON, #00H
MOV IP, #00H
MOV IE, #82H
MOV TMOD, #01H
MOV R6, #E0H
; TCON = 00H, TR = 0 TIMER0 STOP
; TMOD = 01H, SET TIMER0 A 16BIT TIMER
; IP = 00H
; IE = 82H, TIMER0 INTERRUPT ENABLED
; TCON = 10H, TR0 = 1, GO
; ENTER IDLE MODE
; DISABLE CHPCON WRITE-ATTRIBUTE
; TCON = 00H , TR = 0 TIM0 STOP
; IP = 00H
; IE = 82H, TIMER0 INTERRUPT ENABLED
; TMOD = 01H, MODE1
; SET WAKE-UP TIME FOR ERASE OPERATION, ABOUT 15 mS. DEPENDING
; ON USER'S SYSTEM CLOCK RATE.
MOV R7, #B1H
MOV TL0, R6
MOV TH0, R7
ERASE_P_4K:
MOV SFRCN, #22H
MOV TCON, #10H
MOV PCON, #01H
; SFRCN(C7H) = 22H ERASE 32K
; TCON = 10H, TR0 = 1,GO
; ENTER IDLE MODE (FOR ERASE OPERATION)
;*********************************************************************
;* BLANK CHECK
;*********************************************************************
MOV SFRCN, #0H
; READ 32KB APROM MODE
MOV SFRAH, #0H
; START ADDRESS = 0H
MOV SFRAL, #0H
MOV R6, #FEH
; SET TIMER FOR READ OPERATION, ABOUT 1.5 μS.
MOV R7, #FFH
MOV TL0, R6
MOV TH0, R7
BLANK_CHECK_LOOP:
SETB TR0
; ENABLE TIMER 0
MOV PCON, #01H
; ENTER IDLE MODE
MOV A, SFRFD
; READ ONE BYTE
CJNE A, #FFH, BLANK_CHECK_ERROR
- 33 -
Publication Release Date: December 4, 2006
Revision A8
W78E58B/W78E058B
INC SFRAL
; NEXT ADDRESS
MOV A, SFRAL
JNZ BLANK_CHECK_LOOP
INC SFRAH
MOV A, SFRAH
CJNE A, #80H, BLANK_CHECK_LOOP ; END ADDRESS = 7FFFH
JMP PROGRAM_32KROM
BLANK_CHECK_ERROR:
MOV P1, #F0H
MOV P3, #F0H
JMP $
;*******************************************************************************
;* RE-PROGRAMMING 32KB APROM BANK
;*******************************************************************************
PROGRAM_32KROM:
MOV DPTR, #0H
; THE ADDRESS OF NEW ROM CODE
MOV R2, #00H
; TARGET LOW BYTE ADDRESS
MOV R1, #00H
; TARGET HIGH BYTE ADDRESS
MOV DPTR, #0H
; EXTERNAL SRAM BUFFER ADDRESS
MOV SFRAH, R1
; SFRAH, TARGET HIGH ADDRESS
MOV SFRCN, #21H ; SFRCN(C7H) = 21 (PROGRAM 32K)
MOV R6, #BEH
; SET TIMER FOR PROGRAMMING, ABOUT 50 μS.
MOV R7, #FFH
MOV TL0, R6
MOV TH0, R7
PROG_D_32K:
MOV SFRAL, R2
MOVX A, @DPTR
; SFRAL(C4H) = LOW BYTE ADDRESS
; READ DATA FROM EXTERNAL SRAM BUFFER. BY ACCORDING USER?
; CIRCUIT, USER MUST MODIFY THIS INSTRUCTION TO FETCH CODE
; SFRFD(C6H) = DATA IN
; TCON = 10H, TR0 = 1,GO
; ENTER IDLE MODE (PRORGAMMING)
MOV SFRFD, A
MOV TCON, #10H
MOV PCON, #01H
INC DPTR
INC R2
CJNE R2, #0H, PROG_D_32K
INC R1
MOV SFRAH, R1
CJNE R1, #80H, PROG_D_32K
;*****************************************************************************
; * VERIFY 32KB APROM BANK
;*****************************************************************************
MOV R4, #03H
; ERROR COUNTER
MOV R6, #FEH
; SET TIMER FOR READ VERIFY, ABOUT 1.5 μS.
MOV R7, #FFH
MOV TL0, R6
MOV TH0, R7
MOV DPTR, #0H
; The start address of sample code
MOV R2, #0H
; Target low byte address
MOV R1, #0H
; Target high byte address
MOV SFRAH, R1
; SFRAH, Target high address
MOV SFRCN, #00H ; SFRCN = 00 (Read ROM CODE)
- 34 -
W78E58B/W78E058B
READ_VERIFY_32K:
MOV SFRAL, R2
; SFRAL(C4H) = LOW ADDRESS
MOV TCON, #10H
; TCON = 10H, TR0 = 1,GO
MOV PCON, #01H
INC R2
MOVX A, @DPTR
INC DPTR
CJNE A, SFRFD, ERROR_32K
CJNE R2, #0H, READ_VERIFY_32K
INC R1
MOV SFRAH, R1
CJNE R1, #80H, READ_VERIFY_32K
;******************************************************************************
;* PROGRAMMING COMPLETLY, SOFTWARE RESET CPU
;******************************************************************************
MOV CHPENR, #87H
; CHPENR = 87H
MOV CHPENR, #59H
; CHPENR = 59H
MOV CHPCON, #83H
; CHPCON = 83H, SOFTWARE RESET.
ERROR_32K:
DJNZ R4, UPDATE_32K
.
.
.
.
; IF ERROR OCCURS, REPEAT 3 TIMES.
; IN-SYSTEM PROGRAMMING FAIL, USER'S PROCESS TO DEAL WITH IT.
- 35 -
Publication Release Date: December 4, 2006
Revision A8
W78E58B/W78E058B
12. REVISION HISTORY
VERSION
DATE
PAGE
DESCRIPTION
A3
March, 2002
-
Formerly issued
A4
June, 2004
2
Revise part number in the item of packages
A5
April 20, 2005
34
Add Important Notice
A6
June 7, 2005
3
Add Lead Free (RoHS) parts
A7
October 3, 2006
A8
December 4, 2006
Remove block diagram
3
Remove all Leaded package parts
Important Notice
Winbond products are not designed, intended, authorized or warranted for use as components
in systems or equipment intended for surgical implantation, atomic energy control
instruments, airplane or spaceship instruments, transportation instruments, traffic signal
instruments, combustion control instruments, or for other applications intended to support or
sustain life. Further more, Winbond products are not intended for applications wherein failure
of Winbond products could result or lead to a situation wherein personal injury, death or
severe property or environmental damage could occur.
Winbond customers using or selling these products for use in such applications do so at their
own risk and agree to fully indemnify Winbond for any damages resulting from such improper
use or sales.
- 36 -