Preliminary Information X24325 32K 4096 x 8 Bit Advanced 2-Wire Serial E2PROM with Block LockTM Protection FEATURES DESCRIPTION • • The X24325 is a CMOS 32,768 bit serial E2PROM, internally organized 4096 x 8. The X24325 features a serial interface and software protocol allowing operation on a simple two wire bus. • • • • • • • • • 2.7V to 5.5V Power Supply Low Power CMOS —Active Read Current Less Than 1mA —Active Write Current Less Than 3mA —Standby Current Less Than 1µA Internally Organized 4096 x 8 New Programmable Block Lock Protection —Software Write Protection —Programmable hardware Write Protect Block Lock (0, 1/4, 1/2, or all of the E2PROM array) 2 Wire Serial Interface Bidirectional Data Transfer Protocol 32 Byte Page Write Mode —Minimizes Total Write Time Per Byte Self Timed Write Cycle —Typical Write Cycle Time of 5ms High Reliability —Endurance: 100,000 Cycles —Data Retention: 100 Years Available Packages —8-Lead PDIP —8-Lead SOIC (JEDEC) —14-Lead TSSOP Three device select inputs (S0, S1, S2) allow up to eight devices to share a common two wire bus. A Write Protect Register at the highest address location, FFFh, provides three new write protection features: Software Write Protect, Block Write Protect, and Hardware Write Protect. The Software Write Protect feature prevents any nonvolatile writes to the X24325 until the WEL bit in the write protect register is set. The Block Write Protection feature allows the user to individually write protect four blocks of the array by programming two bits in the write protect register. The Programmable Hardware Write Protect feature allows the user to install the X24325 with WP tied to VCC, program the entire memory array in place, and then enable the hardware write protection by programming a WPEN bit in the write protect register. After this, selected blocks of the array, including the write protect register itself, are permanently write protected. Xicor E2PROMs are designed and tested for applications requiring extended endurance. Inherent data retention is greater than 100 years. FUNCTIONAL DIAGRAM WP H.V. GENERATION TIMING & CONTROL START CYCLE VCC VSS SDA WRITE PROTECT REGISTER AND LOGIC START STOP LOGIC CONTROL LOGIC SCL SLAVE ADDRESS REGISTER +COMPARATOR LOAD INC E2PROM 128 X 256 XDEC WORD ADDRESS COUNTER S0 S1 S2 R/W YDEC 8 CK PIN DATA REGISTER DOUT DOUT ACK Xicor, 1995, 1996 Patents Pending 6552-2.4 5/13/96 T1/C10/D0 NS 1 6552 ILL F01.1 Characteristics subject to change without notice X24325 PIN DESCRIPTIONS PIN CONFIGURATIONS Serial Clock (SCL) The SCL input is used to clock all data into and out of the device. 8-LEAD DIP & SOIC Serial Data (SDA) SDA is a bidirectional pin used to transfer data into and out of the device. It is an open drain output and may be wire-ORed with any number of open drain or open collector outputs. S0 1 8 VCC S1 2 7 WP S2 3 6 SCL VSS 4 5 SDA X24325 14-LEAD TSSOP An open drain output requires the use of a pull-up resistor. For selecting typical values, refer to the PullUp Resistor selection graph at the end of this data sheet. S0 1 14 VCC S1 NC 2 13 WP 3 12 NC NC 4 X24325 11 NC Device Select (S0, S1, S2) NC 5 10 NC The device select inputs (S0, S1, S2) are used to set the first three bits of the 8-bit slave address. This allows up to eight X24325’s to share a common bus. These inputs can be static or actively driven. If used statically they must be tied to VSS or VCC as appropriate. If actively driven, they must be driven with CMOS levels (driven to VCC or VSS). S2 6 9 SCL VSS 7 8 SDA 6552 ILL F02.5 Write Protect (WP) The write protect input controls the hardware write protect feature. When held LOW, hardware write protection is disabled and the X24325 can be written normally. When this input is held HIGH, and the WPEN bit in the write protect register is set HIGH, write protection is enabled, and nonvolatile writes are disabled to the selected blocks as well as the write protect register itself. PIN NAMES Symbol Description S0, S1, S2 Device Select Inputs SDA Serial Data SCL Serial Clock WP Write Protect VSS Ground VCC Supply Voltage NC No Connect 6552 FRM T01.1 2 X24325 Clock and Data Conventions Data states on the SDA line can change only during SCL LOW. SDA state changes during SCL HIGH are reserved for indicating start and stop conditions. Refer to Figures 1 and 2. DEVICE OPERATION The X24325 supports a bidirectional bus oriented protocol. The protocol defines any device that sends data onto the bus as a transmitter, and the receiving device as the receiver. The device controlling the transfer is a master and the device being controlled is the slave. The master will always initiate data transfers, and provide the clock for both transmit and receive operations. Therefore, the X24325 will be considered a slave in all applications. Start Condition All commands are preceded by the start condition, which is a HIGH to LOW transition of SDA when SCL is HIGH. The X24325 continuously monitors the SDA and SCL lines for the start condition and will not respond to any command until this condition has been met. Figure 1. Data Validity SCL SDA DATA STABLE DATA CHANGE 6552 ILL F04 Notes: (5) Typical values are for TA = 25°C and nominal supply voltage (5V) (6) tWR is the minimum cycle time from the system perspective when polling techniques are not used. It is the maximum time the device requires to perform the internal write operation. Figure 2. Definition of Start and Stop SCL SDA START BIT STOP BIT 3 6552 ILL F05 X24325 The X24325 will respond with an acknowledge after recognition of a start condition and its slave address. If both the device and a write operation have been selected, the X24325 will respond with an acknowledge after the receipt of each subsequent eight-bit word. Stop Condition All communications must be terminated by a stop condition, which is a LOW to HIGH transition of SDA when SCL is HIGH. The stop condition is also used to place the device into the standby power mode after a read sequence. A stop condition can only be issued after the transmitting device has released the bus. In the read mode the X24325 will transmit eight bits of data, release the SDA line and monitor the line for an acknowledge. If an acknowledge is detected and no stop condition is generated by the master, the X24325 will continue to transmit data. If an acknowledge is not detected, the X24325 will terminate further data transmissions. The master must then issue a stop condition to return the X24325 to the standby power mode and place the device into a known state. Acknowledge Acknowledge is a software convention used to indicate successful data transfer. The transmitting device, either master or slave, will release the bus after transmitting eight bits. During the ninth clock cycle the receiver will pull the SDA line LOW to acknowledge that it received the eight bits of data. Refer to Figure 3. Figure 3. Acknowledge Response From Receiver SCL FROM MASTER 1 8 9 DATA OUTPUT FROM TRANSMITTER DATA OUTPUT FROM RECEIVER START ACKNOWLEDGE 6552 ILL F06 4 X24325 DEVICE ADDRESSING The last bit of the slave address defines the operation to be performed. When set HIGH a read operation is selected, when set LOW a write operation is selected. Following a start condition the master must output the address of the slave it is accessing (see Figure 4). The next three bits are the device select bits. A system could have up to eight X24325’s on the bus. The eight addresses are defined by the state of the S0, S1 and S2 inputs. S0 and S2 of the slave address must be the inverse of the S0 and S2 input pins. Following the start condition, the X24325 monitors the SDA bus comparing the slave address being transmitted with its slave address device type identifier. Upon a correct compare the X24325 outputs an acknowledge on the SDA line. Depending on the state of the R/W bit, the X24325 will execute a read or write operation. Figure 4. Slave Address S2 S1 WRITE OPERATIONS HIGH ORDER WORD ADDRESS DEVICE SELECT S0 A11 A10 A9 A8 Byte Write For a write operation, the X24325 requires a second address field. This address field is the word address, comprised of eight bits, providing access to any one of 4096 words in the array. Upon receipt of the word address, the X24325 responds with an acknowledge and awaits the next eight bits of data, again responding with an acknowledge. The master then terminates the transfer by generating a stop condition, at which time the X24325 begins the internal write cycle to the nonvolatile memory. While the internal write cycle is in progress the X24325 inputs are disabled, and the device will not respond to any requests from the master. Refer to Figure 5 for the address, acknowledge and data transfer sequence. R/W 6552 ILL F07.2 The next four bits of the slave address are an extension of the array’s address and are concatenated with the eight bits of address in the word address field, providing direct access to the whole 4096 x 8 array. Figure 5. Byte Write BUS ACTIVITY: MASTER SDA LINE BUS ACTIVITY: X24325 S T A R T SLAVE ADDRESS WORD ADDRESS S T O P DATA S P A C K A C K A C K 6552 ILL F08 5 X24325 Page Write The X24325 is capable of a 32 byte page write operation. It is initiated in the same manner as the byte write operation, but instead of terminating the write cycle after the first data word is transferred, the master can transmit up to fifteen more words. After the receipt of each word, the X24325 will respond with an acknowledge. Flow 1. ACK Polling Sequence WRITE OPERATION COMPLETED ENTER ACK POLLING ISSUE START After the receipt of each word, the five low order address bits are internally incremented by one. The high order bits of the word address remain constant. If the master should transmit more than 32 words prior to generating the stop condition, the address counter will “roll over” and the previously written data will be overwritten. As with the byte write operation, all inputs are disabled until completion of the internal write cycle. Refer to Figure 6 for the address, acknowledge and data transfer sequence. ISSUE SLAVE ADDRESS AND R/W = 0 ACK RETURNED? ISSUE STOP NO YES Acknowledge Polling The Max Write Cycle Time can be significantly reduced using Acknowledge Polling. To initiate Acknowledge Polling, the master issues a start condition followed by the Slave Address Byte for a write or read operation. If the device is still busy with the high voltage cycle, then no ACK will be returned. If the device has completed the write operation, an ACK will be returned and the host can then proceed with the read or write operation. Refer to Flow 1. NEXT OPERATION A WRITE? NO YES ISSUE BYTE ADDRESS ISSUE STOP PROCEED PROCEED 6552 ILL F09 Figure 6. Page Write BUS ACTIVITY: MASTER SDA LINE BUS ACTIVITY: X24325 S T A R T SLAVE ADDRESS WORD ADDRESS (n) DATA n DATA n+1 S T O P DATA n+31 S P A C K A C K A C K A C K A C K 6552 ILL F10.1 6 X24325 minated by the master; by not responding with an acknowledge and by issuing a stop condition. Refer to Figure 7 for the sequence of address, acknowledge and data transfer. READ OPERATIONS Read operations are initiated in the same manner as write operations with the exception that the R/W bit of the slave address is set HIGH. There are three basic read operations: current address read, random read and sequential read. Random Read Random read operations allow the master to access any memory location in a random manner. Prior to issuing the slave address with the R/W bit set HIGH, the master must first perform a “dummy” write operation. The master issues the start condition, and the slave address with the R/W bit set LOW, followed by the word address it is to read. After the word address acknowledge, the master immediately reissues the start condition and the slave address with the R/W bit set HIGH. This will be followed by an acknowledge from the X24325 and then by the eight-bit word. The read operation is terminated by the master; by not responding with an acknowledge and by issuing a stop condition. Refer to Figure 8 for the address, acknowledge and data transfer sequence. It should be noted that the ninth clock cycle of the read operation is not a “don’t care.” To terminate a read operation, the master must either issue a stop condition during the ninth cycle or hold SDA HIGH during the ninth clock cycle and then issue a stop condition. Current Address Read Internally the X24325 contains an address counter that maintains the address of the last word read, incremented by one or the exact address of the last word written. Therefore, if the last access read was to address n, the next read operation would access data from address n + 1. Upon receipt of the slave address with the R/W set HIGH, the X24325 issues an acknowledge and transmits the eight-bit word. The read operation is ter- Figure 7. Current Address Read BUS ACTIVITY: MASTER SDA LINE S T A R T S T O P SLAVE ADDRESS S P A C K BUS ACTIVITY: X24325 DATA 6552 ILL F11 Figure 8. Random Read BUS ACTIVITY: MASTER SDA LINE BUS ACTIVITY: X24325 S T A R T SLAVE ADDRESS S T A R T WORD ADDRESS n S S T O P SLAVE ADDRESS S A C K A C K P A C K DATA n 6552 ILL F12.1 7 X24325 The data output is sequential, with the data from address n followed by the data from n + 1. The address counter for read operations increments all address bits, allowing the entire memory contents to be serially read during one operation. At the end of the address space (address 4095), the counter “rolls over” to 0 and the X24325 continues to output data for each acknowledge received. Refer to Figure 9 for the address, acknowledge and data transfer sequence. Sequential Read Sequential reads can be initiated as either a current address read or random access read. The first word is transmitted as with the other modes, however, the master now responds with an acknowledge, indicating it requires additional data. The X24325 continues to output data for each acknowledge received. The read operation is terminated by the master; by not responding with an acknowledge and then issuing a stop condition. Figure 9. Sequential Read BUS ACTIVITY: MASTER SLAVE ADDRESS A C K A C K S T O P A C K SDA LINE BUS ACTIVITY: X24325 P A C K DATA n DATA n+1 DATA n+2 DATA n+x 6552 ILL F13 Figure 10. Typical System Configuration VCC PULL-UP RESISTORS SDA SCL MASTER TRANSMITTER/ RECEIVER SLAVE RECEIVER SLAVE TRANSMITTER/ RECEIVER MASTER TRANSMITTER MASTER TRANSMITTER/ RECEIVER 6552 ILL F14 8 X24325 WEL and RWEL are volatile latches that power-up in the LOW (disabled) state. A write to any address other than FFFh, where the Write Protect Register is located, will be ignored (no ack) until the WEL bit is set HIGH. The WEL bit is set by writing 0000001x to address FFFh. Once set, WEL remains HIGH until either reset (by writing 00000000 to FFFh) or until the part powers-up again. The RWEL bit controls writes to the block protect bits. RWEL is set by first setting WEL = 1 and then writing 0000011x to address FFFh. RWEL must be set in order to change the block protect bits, BP0 and BP1, or the WPEN bit. RWEL is reset when the block protect or WPEN bits are changed, or when the part powers-up again. WRITE PROTECT REGISTER The Write Protect Register (WPR) is located at the highest address, FFFh. Figure 11. Write Protect Register WPR (Addr = FFFh) 7 6 5 4 3 2 1 0 WPEN 0 0 BP1 BP0 RWEL WEL 0 6552 ILL F15 WPR.1 = WEL – Write Enable Latch (Volatile) 0 = Write enable latch reset, writes disabled 1 = Write enable latch set, writes enabled Programming the BP or WPEN Bits A three step sequence is required to change the nonvoltaile Block Protect or Write Protect Enable: If WEL = 0 then “no ACK” after first byte of input data. WPR.2 = RWEL – Register Write Enable Latch (Volatile) 0 = Register write enable latch reset, writes disabled 1 = Register write enable latch set, writes enabled 1) Set WEL = 1 (write 00000010 to address FFFh, volatile write cycle) (Start) 2) Set RWEL = 1 (write 00000110 to address FFFh, volatile write cycle) WPR.3, WPR.4 = BP0, BP1 – Block Protect Bits (Nonvolatile) (See Block Protect section for definition) (Start) WPR.7 = WPEN – Write Protect Enable Bit (Nonvolatile) (See Hardware Write Protect section for definition) 3) Set BP1, BP0, and/or WPEN bits (Write w00yz010 to address FFFh) w = WPEN, y = BP1, Z = BP0, Writing to the Write Protect Register The Write Protect Register is written by performing a random write of one byte directly to address, FFFh. If a page write is performed starting with any address other than FFFh, the byte in the array at address FFFh will be written instead of the Write Protect Register (assuming writes are not disabled by the block protect register). (Stop) Step 3 is a nonvolatile write cycle, requiring 10ms to complete. RWEL is reset (0) by this write cycle, requiring another write cycle to set RWEL again before the block protect bits can be changed. RWEL must be 0 in step 3; if w00yz110 is written to address FFFh, RWEL is set but WPEN, BP1 and BP0 are not changed (the device remains at step 2). The state of the Write Protect Register can be read by performing a random read at address FFFh at any time. If a sequential read starting at any other address than FFFh is performed, the contents of the byte in the array at FFFh is read out instead of the Write Protect Register. 9 X24325 Block Protect Bits The Block Protect Bits BP0 and BP1 determine which blocks of the memory are write-protected: Programmable Hardware Write Protect The Write Protect (WP) pin and the Write Protect Enable (WPEN) bit in the Write Protect Register control the programmable hardware write protect feature. Hardware write protection is enabled when the WP pin and the WPEN bit are both HIGH, and disabled when either the WP pin is LOW or the WPEN bit is LOW. When the chip is hardware write-protected, nonvolatile writes are disabled to the Write Protect Register, including the BP bits and the WPEN bit itself, as well as to block-protected sections in the memory array. Only the sections of the memory array that are not block-protected can be written. Note that since the WPEN bit is write-protected, it cannot be changed back to a LOW state, and write protection is disabled as long as the the WP pin is held HIGH. Table 2 defines the write protection status for each state of WPEN and WP. Table 1. Block Protect Bits Protected Addresses BP1 BP0 0 0 None 0 1 C00h–FFFh Upper 1/4 1 0 800h–FFFh Upper 1/2 1 1 0000h–FFFh Full Array (WPR not included) 6552 FRM T02 Table 2. Write Protect Status Table WP WPEN Memory Array (Not Block Protected) 0 X Writable Protected Writable Writable X 0 Writable Protected Writable Writable 1 1 Writable Protected Protected Protected Memory Array (Block Protected) BP Bits WPEN Bit 6552 FRM T03 10 X24325 ABSOLUTE MAXIMUM RATINGS* Temperature Under Bias X24325.......................................–65°C to +135°C Storage Temperature ........................–65°C to +150°C Voltage on any Pin with Respect to VSS .................................... –1V to +7V D.C. Output Current ..............................................5mA Lead Temperature (Soldering, 10 Seconds) ...... 300°C *COMMENT Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and the functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. RECOMMENDED OPERATING CONDITIONS Temperature Min. Max. Supply Voltage Limits 4.5V to 5.5V 2.7V to 5.5V Commercial 0°C +70°C X24325 Industrial –40°C +85°C X24325-2.7 Military –55°C +125°C 6552 FRM T05 6552 FRM T04 D.C. OPERATING CHARACTERISTICS Limits Symbol Parameter Min. Max. Units Test Conditions ICC1 VCC Supply Current (Read) 1 mA ICC2 VCC Supply Current (Write) 3 mA SCL = VCC X 0.1/VCC X 0.9 Levels @ 100KHz, SDA = Open, All Other Inputs = VSS or VCC – 0.3V ISB1(1) VCC Standby Current 50 µA SCL = SDA = VCC, All Other Inputs = VSS or VCC – 0.3V, VCC = 5V ± 10% ISB2(1) VCC Standby Current 1 µA SCL = SDA = VCC, All Other Inputs = VSS or VCC – 0.3V, VCC = 2.7V ILI Input Leakage Current 10 µA VIN = VSS to VCC ILO Output Leakage Current 10 µA VOUT = VSS to VCC VlL(2) Input LOW Voltage –1 VCC x 0.3 V VIH(2) Input HIGH Voltage VCC x 0.7 VCC + 0.5 V VOL Output LOW Voltage 0.4 V IOL = 3mA, VCC = 4.5V 6552 FRM T06.1 CAPACITANCE TA = +25°C, f = 1MHz, VCC = 5V Symbol Parameter Max. Units Test Conditions CI/O(3) Input/Output Capacitance (SDA) 8 pF VI/O = 0V CIN(3) Input Capacitance (S1, S2, SCL) 6 pF VIN = 0V 6552 FRM T07.1 Notes: (1) Must perform a stop command prior to measurement. (2) VIL min. and VIH max. are for reference only and are not 100% tested. (3) This parameter is periodically sampled and not 100% tested. 11 X24325 EQUIVALENT A.C. LOAD CIRCUIT A.C. CONDITIONS OF TEST Input Pulse Levels VCC x 0.1 to VCC x 0.9 Input Rise and Fall Times 5V 10ns Input and Output Timing Levels 1533Ω OUTPUT VCC X 0.5 6552 FRM T08.1 100pF 6552 ILL F16 A.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions, unless otherwise specified.) Read & Write Cycle Limits Symbol Parameter Min. Max. Units 0 100 KHz 100 ns 3.5 µs fSCL SCL Clock Frequency TI Noise Suppression Time Constant at SCL, SDA Inputs tAA SCL LOW to SDA Data Out Valid 0.3 tBUF Time the Bus Must Be Free Before a New Transmission Can Start 4.7 µs tHD:STA Start Condition Hold Time 4 µs tLOW Clock LOW Period 4.7 µs tHIGH Clock HIGH Period 4 µs tSU:STA Start Condition Setup Time (for a Repeated Start Condition) 4.7 µs tHD:DAT Data In Hold Time 0 µs tSU:DAT Data In Setup Time 250 ns tR SDA and SCL Rise Time 1 µs tF SDA and SCL Fall Time 300 ns tSU:STO Stop Condition Setup Time 4.7 µs tDH Data Out Hold Time 300 ns 6552 FRM T09.1 POWER-UP TIMING(4) Symbol Parameter Max. Units tPUR Power-up to Read Operation 1 ms tPUW Power-up to Write Operation 5 ms 6552 FRM T10 Notes: (4) tPUR and tPUW are the delays required from the time V CC is stable until the specified operation can be initiated. These parameters are periodically sampled and not 100% tested. 12 X24325 Bus Timing tHIGH tF tLOW tR SCL tSU:STA tHD:STA tHD:DAT tSU:DAT tSU:STO SDA IN tAA tDH tBUF SDA OUT 6552 ILL F17 Write Cycle Limits Symbol Parameter tWR(6) Write Cycle Time Min. Typ.(5) Max. Units 5 10 ms 6552 FRM T11.1 The write cycle time is the time from a valid stop condition of a write sequence to the end of the internal erase/program cycle. During the write cycle, the X24325 bus interface circuits are disabled, SDA is allowed to remain HIGH, and the device does not respond to its slave address. Bus Timing SCL SDA 8th BIT ACK WORD n tWR STOP CONDITION START CONDITION 6552 ILL F18 Notes: (5) Typical values are for TA = 25°C and nominal supply voltage (5V). (6) tWR is the minimum cycle time to be allowed from the system perspective unless polling techniques are used. It is the maximum time the device requires to automatically complete the internal write operation. Guidelines for Calculating Typical Values of Bus Pull-Up Resistors SYMBOL TABLE WAVEFORM RESISTANCE (KΩ) 120 RMIN = 100 80 VCC MAX =1.8KΩ IOL MIN RMAX = tR CBUS MAX. RESISTANCE 60 40 20 MIN. RESISTANCE 0 0 20 40 60 80 100 120 BUS CAPACITANCE (pF) 6552 ILL F19 13 INPUTS OUTPUTS Must be steady Will be steady May change from LOW to HIGH Will change from LOW to HIGH May change from HIGH to LOW Will change from HIGH to LOW Don’t Care: Changes Allowed N/A Changing: State Not Known Center Line is High Impedance X24325 PACKAGING INFORMATION 8-LEAD PLASTIC DUAL IN-LINE PACKAGE TYPE P 0.430 (10.92) 0.360 (9.14) 0.260 (6.60) 0.240 (6.10) PIN 1 INDEX PIN 1 0.300 (7.62) REF. HALF SHOULDER WIDTH ON ALL END PINS OPTIONAL 0.145 (3.68) 0.128 (3.25) SEATING PLANE 0.025 (0.64) 0.015 (0.38) 0.065 (1.65) 0.045 (1.14) 0.150 (3.81) 0.125 (3.18) 0.020 (0.51) 0.016 (0.41) 0.110 (2.79) 0.090 (2.29) 0.015 (0.38) MAX. 0.060 (1.52) 0.020 (0.51) 0.325 (8.25) 0.300 (7.62) 0° 15° TYP. 0.010 (0.25) NOTE: 1. ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 2. PACKAGE DIMENSIONS EXCLUDE MOLDING FLASH 3926 FHD F01 14 X24325 PACKAGING INFORMATION 8-LEAD PLASTIC SMALL OUTLINE GULL WING PACKAGE TYPE S 0.150 (3.80) 0.158 (4.00) 0.228 (5.80) 0.244 (6.20) PIN 1 INDEX PIN 1 0.014 (0.35) 0.019 (0.49) 0.188 (4.78) 0.197 (5.00) (4X) 7° 0.053 (1.35) 0.069 (1.75) 0.004 (0.19) 0.010 (0.25) 0.050 (1.27) 0.010 (0.25) X 45° 0.020 (0.50) 0.050" TYPICAL 0.050" TYPICAL 0° – 8° 0.0075 (0.19) 0.010 (0.25) 0.250" 0.016 (0.410) 0.037 (0.937) 0.030" TYPICAL 8 PLACES FOOTPRINT NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 3926 FHD F22.1 15 X24325 PACKAGING INFORMATION 14-LEAD PLASTIC, TSSOP PACKAGE TYPE V .025 (.65) BSC .169 (4.3) .252 (6.4) BSC .177 (4.5) .193 (4.9) .200 (5.1) .047 (1.20) .0075 (.19) .0118 (.30) .002 (.05) .006 (.15) .010 (.25) Gage Plane 0° – 8° Seating Plane .019 (.50) .029 (.75) Detail A (20X) .031 (.80) .041 (1.05) See Detail “A” NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 3926 FHD F32 16 X24325 ORDERING INFORMATION X24325 X X -X VCC Range Blank = 4.5V to 5.5V 2.7 = 2.7V to 5.5V Device Temperature Range Blank = 0°C to +70°C I = –40°C to +85°C M = –55°C to +125°C Package P = 8-Lead Plastic DIP S = 8-Lead SOIC (JEDEC) V = 14-Lead TSSOP Part Mark Convention X24325 X P = 8-Lead Plastic DIP Blank = 8-Lead SOIC (JEDEC) V = 14-Lead TSSOP X Blank = 4.5V to 5.5V, 0°C to +70°C I = 4.5V to 5.5V, –40°C to +85°C F = 2.7V to 5.5V, 0°C to +70°C G = 2.7V to 5.5V, –40°C to +85°C LIMITED WARRANTY Devices sold by Xicor, Inc. are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. Xicor, Inc. makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. Xicor, Inc. makes no warranty of merchantability or fitness for any purpose. Xicor, Inc. reserves the right to discontinue production and change specifications and prices at any time and without notice. Xicor, Inc. assumes no responsibility for the use of any circuitry other than circuitry embodied in a Xicor, Inc. product. No other circuits, patents, licenses are implied. U.S. PATENTS Xicor products are covered by one or more of the following U.S. Patents: 4,263,664; 4,274,012; 4,300,212; 4,314,265; 4,326,134; 4,393,481; 4,404,475; 4,450,402; 4,486,769; 4,488,060; 4,520,461; 4,533,846; 4,599,706; 4,617,652; 4,668,932; 4,752,912; 4,829, 482; 4,874, 967; 4,883, 976. Foreign patents and additional patents pending. LIFE RELATED POLICY In situations where semiconductor component failure may endanger life, system designers using this product should design the system with appropriate error detection and correction, redundancy and back-up features to prevent such an occurence. Xicor's products are not authorized for use in critical components in life support devices or systems. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 17