Recommended System Management Alternative: X5643 X25650 64K 8K x 8 Bit N O T FO R R EC N O EW M M D E ES N D IG E N D 5MHz SPI Serial EEPROM with Block Lock™ Protection FEATURES • Packages —8-lead SOIC —14-lead SOIC • 5MHz clock rate • Low Power CMOS —<1µA standby current —<5mA active current • 2.5V To 5.5V power supply • SPI modes (0,0 & 1,1) • 8K X 8 bits —32 byte page mode • Block lock protection —Protect 1/4, 1/2 or all of EEPROM array • Programmable hardware write protection —In-circuit programmable ROM mode • Built-in inadvertent write protection —Power-up/down protection circuitry —Write enable latch —Write protect pin • Self-timed write cycle —5ms write cycle time (typical) • High reliability —Endurance: 1,000,000 cycles —Data retention: 100 years —ESD protection: 2000V on all pins DESCRIPTION The X25650 is a CMOS 65,536-bit serial EEPROM, internally organized as 8K x 8. The X25650 features a Serial Peripheral Interface (SPI) and software protocol, allowing operation on a simple three-wire bus. The bus signals are a clock input (SCK) plus separate data in (SI) and data out (SO) lines. Access to the device is controlled through a chip select (CS) input, allowing any number of devices to share the same bus. The X25650 also features two additional inputs that provide the end user with added flexibility. By asserting the HOLD input, the X25650 will ignore transitions on its inputs, thus allowing the host to service higher priority interrupts. The WP input can be used as a hardwire input to the X25650 disabling all write attempts to the status register, thus providing a mechanism for limiting end user capability of altering 0, 1/4, 1/2 or all of the memory. The X25650 utilizes Xicor’s proprietary Direct Write™ cell, providing a minimum endurance of 1,000,000 cycles and a minimum data retention of 100 years. BLOCK DIAGRAM Status Register Write Protect Logic X Decode Logic 8Kbyte Array 64 SO SI SCK CS HOLD Command Decode and Control Logic 64 X 256 64 64 X 256 128 128 X 256 WP Write Control and Timing Logic 32 8 Y Decode Data Register Direct Write™ and Block Lock™ Protection is a trademark of Xicor, Inc. REV 1.1 9/8/00 This Material Copyrighted by Its Respective Manufacturer www.xicor.com Characteristics subject to change without notice. 1 of 15 X25650 PIN DESCRIPTIONS PIN NAMES Symbol Serial Input (SI) SI is the serial data input pin. All opcodes, byte addresses, and data to be written to the memory are input on this pin. Data is latched by the rising edge of the serial clock. SCK Description N O T FO R R EC N O EW M M D E ES N D IG E N D Serial Output (SO) SO is a push/pull serial data output pin. During a read cycle, data is shifted out on this pin. Data is clocked out by the falling edge of the serial clock. SO Serial Output SI Serial Input Serial Clock Input WP Write Protect Input VSS Ground VCC Supply Voltage Hold Input NC The Serial Clock controls the serial bus timing for data input and output. Opcodes, addresses, or data present on the SI pin are latched on the rising edge of the clock input, while data on the SO pin change after the falling edge of the clock input. SOIC When CS is HIGH, the X25650 is deselected and the SO output pin is at high impedance and unless an internal write operation is underway, the X25650 will be in the standby power mode. CS LOW enables the X25650, placing it in the active power mode. It should be noted that after power-up, a HIGH to LOW transition on CS is required prior to the start of any operation. Write Protect (WP) When WP is LOW and the nonvolatile bit WPEN is “1”, nonvolatile writes to the X25650 status register are disabled, but the part otherwise functions normally. When WP is held HIGH, all functions, including nonvolatile writes operate normally. WP going LOW while CS is still LOW will interrupt a write to the X25650 status register. If the internal write cycle has already been initiated, WP going LOW will have no affect on a write. The WP pin function is blocked when the WPEN bit in the status register is “0”. This allows the user to install the X25650 in a system with WP pin grounded and still be able to write to the status register. The WP pin functions will be enabled when the WPEN bit is set “1”. No Connect PIN CONFIGURATION Chip Select (CS) This Material Copyrighted by Its Respective Manufacturer Chip Select Input HOLD Serial Clock (SCK) REV 1.1 9/8/00 CS CS 1 8 VCC SO 2 7 HOLD WP 3 6 SCK VSS 4 5 SI 14-Lead SOIC NC NC CS SO WP VSS NC 1 2 3 4 5 6 7 14 13 12 11 10 9 8 NC NC VCC HOLD SCK SI NC * Pin 3 and Pin 4 are internally connected. Hold (HOLD) HOLD is used in conjunction with the CS pin to pause the device. Once the part is selected and a serial sequence is underway, HOLD may be used to pause the serial communication with the controller without resetting the serial sequence. To pause, HOLD must be brought LOW while SCK is LOW. To resume communication, HOLD is brought HIGH, again while SCK is LOW. If the pause feature is not used, HOLD should be held HIGH at all times. www.xicor.com Characteristics subject to change without notice. 2 of 15 X25650 PRINCIPLES OF OPERATION N O T FO R R EC N O EW M M D E ES N D IG E N D The X25650 is a 8K x 8 EEPROM designed to interface directly with the synchronous serial peripheral interface (SPI) of many popular microcontroller families. Status Register The RDSR instruction provides access to the status register. The status register may be read at any time, even during a write cycle. The status register is formatted as follows: The X25650 contains an 8-bit instruction register. It is accessed via the SI input, with data being clocked in on the rising SCK. CS must be LOW and the HOLD and WP inputs must be HIGH during the entire operation. 7 6 5 4 3 2 1 0 WPEN X X X BL1 BL0 WEL WIP Table 1 contains a list of the instructions and their opcodes. All instructions, addresses and data are transferred MSB first. WPEN, BL0 and BL1 are set by the WRSR instruction. WEL and WIP are read-only and automatically set by other operations. Data input is sampled on the first rising edge of SCK after CS goes LOW. SCK is static, allowing the user to stop the clock and then resume operations. If the clock line is shared with other peripheral devices on the SPI bus, the user can assert the HOLD input to place the X25650 into a “PAUSE” condition. After releasing HOLD, the X25650 will resume operation from the point when HOLD was first asserted. The Write-In-Process (WIP) bit indicates whether the X25650 is busy with a write operation. When set to a “1”, a write is in progress, when set to a “0”, no write is in progress. During a write, all other bits are “don’t care”. Write Enable Latch The X25650 contains a “write enable” latch. This latch must be SET before a write operation will be completed internally. The WREN instruction will set the latch and the WRDI instruction will reset the latch. This latch is automatically reset upon a power-up condition and after the completion of a byte, page, or status register write cycle. The Write Enable Latch (WEL) bit indicates the status of the “write enable” latch. When set to a “1”, the latch is set, when set to a “0”, the latch is reset. The Block Lock (BL0 and BL1) bits are nonvolatile and allow the user to select one of four levels of protection. The X25650 is divided into four 16384-bit segments. One, two, or all four of the segments may be protected. That is, the user may read the segments but will be unable to alter (write) data within the selected segments. The partitioning is controlled as illustrated below. Status Register Bits BL1 BL0 Array Addresses Protected 0 0 None 0 1 $1800–$1FFF 1 0 $1000–$1FFF 1 1 $0000–$1FFF Table 1. Instruction Set Instruction Name Instruction Format* Note: Operation WREN 0000 0110 Set the write enable latch (enable write operations) WRDI 0000 0100 Reset the write enable latch (disable write operations) RDSR 0000 0101 Read status register WRSR 0000 0001 Write status register READ 0000 0011 Read data from memory array beginning at selected address WRITE 0000 0010 Write data to memory array beginning at selected address (1 to 32 bytes) *Instructions are shown MSB in leftmost position. Instructions are transferred MSB first. REV 1.1 9/8/00 This Material Copyrighted by Its Respective Manufacturer www.xicor.com Characteristics subject to change without notice. 3 of 15 X25650 The Write-Protect-Enable (WPEN) bit is available for the X25650 as a nonvolatile enable bit for the WP pin. WP WEL Protected Blocks Unprotected Blocks Status Register 0 X 0 Protected Protected Protected 0 X 1 Protected Writable Writable 1 LOW 0 Protected Protected Protected 1 LOW 1 Protected Writable Protected X HIGH 0 Protected Protected Protected X HIGH 1 Protected Writable Writable N O T FO R R EC N O EW M M D E ES N D IG E N D WPEN Programmable Hardware Write Protection The Write Protect (WP) pin and the nonvolatile Write Protect Enable (WPEN) bit in the Status Register control the Programmable Hardware Write Protect feature. Hardware Write Protection is enabled when WP pin is LOW, and the WPEN bit is “1”. Hardware Write Protection is disabled when either the WP pin is HIGH or the WPEN bit is “0”. When the chip is hardware write protected, nonvolatile writes are disabled to the Status Register, including the Block Lock bits and the WPEN bit itself, as well as the block-protected sections in the memory array. Only the sections of the memory array that are not block-protected can be written. In Circuit Programmable ROM Mode Note that since the WPEN bit is write protected, it cannot be changed back to a LOW state; so write protection is enabled as long as the WP pin is held LOW. Thus an In Circuit Programmable ROM function can be implemented by hardwiring the WP pin to Vss, writing to and Block Locking the desired portion of the array to be ROM, and then programming the WPEN bit HIGH. The table above defines the program protect status for each combination of WPEN and WP. Clock and Data Timing Data input on the SI line is latched on the rising edge of SCK. Data is output on the SO line by the falling edge of SCK. Read Sequence When reading from the EEPROM memory array, CS is first pulled LOW to select the device. The 8-bit READ instruction is transmitted to the X25650, followed by the 16-bit address of which the last 13 are used. After the READ opcode and address are sent, the data stored in the memory at the selected address is shifted out on the SO line. The data stored in memory at the REV 1.1 9/8/00 This Material Copyrighted by Its Respective Manufacturer next address can be read sequentially by continuing to provide clock pulses. The address is automatically incremented to the next higher address after each byte of data is shifted out. When the highest address is reached ($1FFF) the address counter rolls over to address $0000 allowing the read cycle to be continued indefinitely. The read operation is terminated by taking CS HIGH. Refer to the read EEPROM array operation sequence illustrated in Figure 1. To read the status register the CS line is first pulled LOW to select the device followed by the 8-bit RDSR instruction. After the RDSR opcode is sent, the contents of the status register are shifted out on the SO line. Figure 2 illustrates the read status register sequence. Write Sequence Prior to any attempt to write data into the X25650, the “write enable” latch must first be set by issuing the WREN instruction (See Figure 3). CS is first taken LOW, then the WREN instruction is clocked into the X25650. After all eight bits of the instruction are transmitted, CS must then be taken HIGH. If the user continues the write operation without taking CS HIGH after issuing the WREN instruction, the write operation will be ignored. To write data to the EEPROM memory array, the user issues the WRITE instruction, followed by the address and then the data to be written. This is minimally a thirtytwo clock operation. CS must go LOW and remain LOW for the duration of the operation. The host may continue to write up to 32 bytes of data to the X25650. The only restriction is the 32 bytes must reside on the same page. If the address counter reaches the end of the page and the clock continues, the counter will “roll over” to the first address of the page and overwrite any data that may have been written. www.xicor.com Characteristics subject to change without notice. 4 of 15 X25650 The HOLD input may be tied HIGH either directly to VCC or tied to VCC through a resistor. N O T FO R R EC N O EW M M D E ES N D IG E N D For the write operation (byte or page write) to be completed, CS can only be brought HIGH after bit 0 of data byte N is clocked in. If it is brought HIGH at any other time the write operation will not be completed. Refer to Figures 4 and 5 below for a detailed illustration of the write sequences and time frames in which CS going HIGH are valid. Operational Notes The X25650 powers-up in the following state: • The device is in the low power standby state. • A HIGH to LOW transition on CS is required to enter an active state and receive an instruction. • SO pin is high impedance. • The “write enable” latch is reset. To write to the status register, the WRSR instruction is followed by the data to be written. Data bits 0, 1, 4, 5 and 6 must be “0”. Figure 6 illustrates this sequence. While the write is in progress following a status register or EEPROM write sequence, the status register may be read to check the WIP bit. During this time the WIP bit will be HIGH. Data Protection The following circuitry has been included to prevent inadvertent writes: • The “write enable” latch is reset upon power-up. • A WREN instruction must be issued to set the “write enable” latch. • CS must come HIGH at the proper clock count in order to start a write cycle. Hold Operation The HOLD input should be HIGH (at VIH) under normal operation. If a data transfer is to be interrupted HOLD can be pulled LOW to suspend the transfer until it can be resumed. The only restriction is the SCK input must be LOW when HOLD is first pulled LOW and SCK must also be LOW when HOLD is released. Figure 1. Read EEPROM Array Operation Sequence CS 0 1 2 3 4 5 6 7 8 9 10 20 21 22 23 24 25 26 27 28 29 30 SCK Instruction SI SO 16 Bit Address 15 14 13 3 2 1 0 Data Out High Impedance 7 6 5 4 3 2 1 0 MSB REV 1.1 9/8/00 This Material Copyrighted by Its Respective Manufacturer www.xicor.com Characteristics subject to change without notice. 5 of 15 X25650 N O T FO R R EC N O EW M M D E ES N D IG E N D Figure 2. Read Status Register Operation Sequence CS 0 1 2 3 4 5 6 7 8 9 7 6 10 11 12 13 14 SCK Instruction SI Data Out High Impedance SO 5 4 3 2 1 0 MSB Figure 3. Write Enable Latch Sequence CS 0 1 2 3 4 5 6 7 SCK SI High Impedance SO Figure 4. Byte Write Operation Sequence CS 0 1 2 3 4 5 6 7 8 9 10 20 21 22 23 24 25 26 27 28 29 30 31 SCK Instruction 15 14 13 SI SO 16 Bit Address 3 2 Data Byte 1 0 7 6 5 4 3 2 1 0 High Impedance REV 1.1 9/8/00 This Material Copyrighted by Its Respective Manufacturer www.xicor.com Characteristics subject to change without notice. 6 of 15 X25650 N O T FO R R EC N O EW M M D E ES N D IG E N D Figure 5. Page Write Operation Sequence CS 0 1 2 3 4 5 6 7 8 9 10 20 21 22 23 24 25 26 27 28 29 30 31 SCK Instruction 16 Bit Address SI 15 14 13 3 Data Byte 1 2 1 7 0 6 5 4 3 2 1 0 CS 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 SCK Data Byte 2 SI 7 6 5 4 3 2 Data Byte 3 1 0 7 6 5 4 Byte N 3 2 1 0 7 8 9 10 6 5 4 3 2 1 0 Figure 6. Write Status Register Operation Sequence CS 0 1 2 3 4 5 6 11 12 13 14 15 SCK Instruction SI SO Data Byte 7 6 5 4 3 2 1 0 High Impedance REV 1.1 9/8/00 This Material Copyrighted by Its Respective Manufacturer www.xicor.com Characteristics subject to change without notice. 7 of 15 X25650 COMMENT Temperature under bias ....................–65°C to +135°C Storage temperature .........................–65°C to +150°C Voltage on any pin with respect to VSS ....... –1V to +7V D.C. output current ............................................... 5mA (soldering, 10 seconds)......................................300°C Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; functional operation of the device (at these or any other conditions above those indicated in the operational sections of this specification) is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. N O T FO R R EC N O EW M M D E ES N D IG E N D ABSOLUTE MAXIMUM RATINGS RECOMMENDED OPERATING CONDITIONS Temperature Min. Max. Supply Voltage Limits Commercial 0°C +70°C X25650-2.5 2.5V to 5.5V Industrial –40°C +85°C D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.) Limits Symbol Parameter Min. Max. Unit Test Conditions ICC VCC supply current (active) 5 mA SCK = VCC x 0.1/VCC x 0.9 @ 5MHz, SO = Open, CS = VSS ISB VCC supply current (standby) 1 µA CS = VCC, VIN = VSS or VCC – 0.3V ILI Input leakage current 10 µA VIN = VSS to VCC ILO Output leakage current 10 µA VOUT = VSS to VCC VCC x 0.3 V VCC x 0.7 VCC + 0.5 V (1) Input LOW voltage (1) VIH Input HIGH voltage VOL1 Output LOW voltage VOH1 Output HIGH voltage VOL2 Output LOW voltage VOH2 Output HIGH voltage VIL –1 0.4 VCC – 0.8 0.4 VCC – 0.3 V IOL = 3mA, VCC = 5V V IOH = –1.6mA, VCC = 5V V IOL = 1.5mA, VCC = 3V V IOH = –0.4mA, VCC = 3V POWER-UP TIMING Symbol (3) (3) TPUR TPUW Parameter Min. Max. Unit Power-up to read operation 1 ms Power-up to write operation 1 ms CAPACITANCE TA = +25°C, f = 1MHz, VCC = 5V Symbol CI/O(3) (3) CIN Notes: (1) (2) (3) Max. Unit Test Conditions Output capacitance (SO) Parameter 8 pF VI/O = 0V Input capacitance (SCK, SI, CS, WP, HOLD) 6 pF VIN = 0V VIL min. and VIH max. are for reference only and are not tested. This parameter is periodically sampled and not 100% tested. tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated. These parameters are periodically sampled and not 100% tested. REV 1.1 9/8/00 This Material Copyrighted by Its Respective Manufacturer www.xicor.com Characteristics subject to change without notice. 8 of 15 X25650 A.C. CONDITIONS OF TEST Input pulse levels VCC x 0.1 to VCC x 0.9 Input rise and fall times 10ns Input and output timing levels VCC X 0.5 N O T FO R R EC N O EW M M D E ES N D IG E N D EQUIVALENT A.C. LOAD CIRCUIT 5V 3V 1.44KΩ Output 1.95KΩ 1.64KΩ 100pF Output 4.63KΩ 100pF A.C. OPERATING CHARACTERISTICS Data Input Timing Symbol Parameter Min. Max. Unit 0 5 MHz fSCK Clock frequency tCYC Cycle time 200 ns tLEAD CS lead time 100 ns tLAG CS lag time 100 ns tWH Clock HIGH time 80 ns tWL Clock LOW time 80 ns tSU Data setup time 20 ns tH Data hold time 20 ns (4) tRI Data in rise time 2 µs tFI(4) Data in fall time 2 µs tHD HOLD setup time 40 ns tCD HOLD hold time 40 ns tCS CS deselect time 100 ns (5) tWC Write cycle time 10 ms Min. Max. Unit 0 5 MHz 100 ns Data Output Timing Symbol Parameter fSCK Clock frequency tDIS Output disable time tV Output valid from clock LOW tHO Output hold time tRO(4) 80 0 ns ns Output rise time 50 ns (4) Output fall time 50 ns (4) HOLD HIGH to output in low Z 50 ns (4) HOLD LOW to output in high Z 50 ns tFO tLZ tHZ Notes: (4) This parameter is periodically sampled and not 100% tested. (5) tWC is the time from the rising edge of CS after a valid write sequence has been sent to the end of the self-timed internal nonvolatile write cycle. REV 1.1 9/8/00 This Material Copyrighted by Its Respective Manufacturer www.xicor.com Characteristics subject to change without notice. 9 of 15 X25650 N O T FO R R EC N O EW M M D E ES N D IG E N D Serial Output Timing CS tCYC tWH tLAG SCK tV SO SI tWL tHO MSB OUT tDIS MSB–1 OUT LSB OUT ADDR LSB IN Serial Input Timing tCS CS tLEAD tLAG SCK tSU SI SO tH tRI MSB IN tFI LSB IN High Impedance REV 1.1 9/8/00 This Material Copyrighted by Its Respective Manufacturer www.xicor.com Characteristics subject to change without notice. 10 of 15 X25650 Hold Timing N O T FO R R EC N O EW M M D E ES N D IG E N D CS tHD tCD tCD tHD SCK tHZ tLZ SO SI HOLD REV 1.1 9/8/00 This Material Copyrighted by Its Respective Manufacturer www.xicor.com Characteristics subject to change without notice. 11 of 15 X25650 N O T FO R R EC N O EW M M D E ES N D IG E N D PACKAGING INFORMATION 8-Lead Plastic Small Outline Gull Wing Package Type S 0.150 (3.80) 0.228 (5.80) 0.158 (4.00) 0.244 (6.20) Pin 1 Index Pin 1 0.014 (0.35) 0.019 (0.49) 0.188 (4.78) 0.197 (5.00) (4X) 7° 0.053 (1.35) 0.069 (1.75) 0.004 (0.19) 0.010 (0.25) 0.050 (1.27) 0.010 (0.25) X 45° 0.020 (0.50) 0.050" Typical 0.050" Typical 0° - 8° 0.0075 (0.19) 0.010 (0.25) 0.250" 0.016 (0.410) 0.037 (0.937) 0.030" Typical 8 Places FOOTPRINT NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) REV 1.1 9/8/00 This Material Copyrighted by Its Respective Manufacturer www.xicor.com Characteristics subject to change without notice. 12 of 15 X25650 N O T FO R R EC N O EW M M D E ES N D IG E N D PACKAGING INFORMATION 14-Lead Plastic Small Outline Gullwing Package Type S 0.150 (3.80) 0.228 (5.80) 0.158 (4.00) 0.244 (6.20) Pin 1 Index Pin 1 0.014 (0.35) 0.020 (0.51) 0.336 (8.55) 0.345 (8.75) (4X) 7° 0.053 (1.35) 0.069 (1.75) 0.004 (0.10) 0.010 (0.25) 0.050 (1.27) 0.050"Typical 0.010 (0.25) 0.020 (0.50) X 45° 0.050"Typical 0° – 8° 0.0075 (0.19) 0.010 (0.25) 0.250" 0.016 (0.410) 0.037 (0.937) 0.030"Typical 14 Places FOOTPRINT NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) REV 1.1 9/8/00 This Material Copyrighted by Its Respective Manufacturer www.xicor.com Characteristics subject to change without notice. 13 of 15 X25650 PACKAGING INFORMATION N O T FO R R EC N O EW M M D E ES N D IG E N D 8-Lead XBGA Complete Part Number Top Mark X25650Z - 2.5 X25650ZI - 2.5 XAAS XAAT 8-Lead XBGA: Top View .159 in. HOLD 1 8 SO VCC 2 7 S1 3 6 CS VSS SCK 4 5 WP .083 in. NOTE: ALL DIMENSIONS IN µM (to convert into inches, 1µm = 3.94 x 10-5 inch) ALL DIMENSIONS ARE TYPICAL VALUES REV 1.1 9/8/00 This Material Copyrighted by Its Respective Manufacturer www.xicor.com Characteristics subject to change without notice. 14 of 15 X25650 Ordering Information X25650 T -V N O T FO R R EC N O EW M M D E ES N D IG E N D P VCC Limits 2.5 = 2.5 to 5.5V Device Temperature Range Blank = Commercial = 0°C to +70°C I = Industrial = –40°C to +85°C Package S8 = 8-Lead SOIC S14 = 14-Lead SOIC Part Mark Convention Other Packages X25650 X Blank = 8-Lead SOIC S = 14-Lead SOIC X AE = 2.5V to 5.5V, 0°C to 70°C AF = 2.5V to 5.5V, –40°C to +85°C LIMITED WARRANTY ©Xicor, Inc. 2000 Patents Pending Devices sold by Xicor, Inc. are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. Xicor, Inc. makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. Xicor, Inc. makes no warranty of merchantability or fitness for any purpose. Xicor, Inc. reserves the right to discontinue production and change specifications and prices at any time and without notice. Xicor, Inc. assumes no responsibility for the use of any circuitry other than circuitry embodied in a Xicor, Inc. product. No other circuits, patents, or licenses are implied. TRADEMARK DISCLAIMER: Xicor and the Xicor logo are registered trademarks of Xicor, Inc. AutoStore, Direct Write, Block Lock, SerialFlash, MPS, and XDCP are also trademarks of Xicor, Inc. All others belong to their respective owners. U.S. PATENTS Xicor products are covered by one or more of the following U.S. Patents: 4,326,134; 4,393,481; 4,404,475; 4,450,402; 4,486,769; 4,488,060; 4,520,461; 4,533,846; 4,599,706; 4,617,652; 4,668,932; 4,752,912; 4,829,482; 4,874,967; 4,883,976; 4,980,859; 5,012,132; 5,003,197; 5,023,694; 5,084,667; 5,153,880; 5,153,691; 5,161,137; 5,219,774; 5,270,927; 5,324,676; 5,434,396; 5,544,103; 5,587,573; 5,835,409; 5,977,585. Foreign patents and additional patents pending. LIFE RELATED POLICY In situations where semiconductor component failure may endanger life, system designers using this product should design the system with appropriate error detection and correction, redundancy and back-up features to prevent such an occurrence. Xicor’s products are not authorized for use in critical components in life support devices or systems. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. REV 1.1 9/8/00 This Material Copyrighted by Its Respective Manufacturer www.xicor.com Characteristics subject to change without notice. 15 of 15