X-Valve® 8 mm switching soleniod valves FEATURES · 3-way, 2 position valve (NO, NC & Distributor) · Compact size, only 8 mm in width · Meets pressure requirements including 6, 30 & 100 psi · Excellent leakage specification for over 25 million cycles · Ensures high reliability with its single piece body design · Barbed pressure ports allow for direct tubing or manifold assemblies · Non-elastomeric versions with enhanced media compatibility available on request MEDIA COMPATIBILITY PHYSICAL PROPERTIES Non-reactive gases and selected liquids Operating environment X5... all other 15 to 50 °C 0 to 50 °C WETTED MATERIALS Storage temperature PBT (polybutylene terephthalate); 430 series stainless steel; 302 series stainless steel (passivated); FKM (fluoroelastomer); EPDM (ethylene propylene diene monomer); silicone -40 to 70 °C Length 24 mm (0.92 in) Width 7.9 mm (0.31 in) Height 9.5 mm (0.375 in) Spacing 8 mm (centerline) ELECTRICAL Power X1... (6 psi) all other (30 psi, 100 psi) Voltage Electrical connections 0.5 W 1.0 W 3, 5, 12, 24 VDC Porting Universal barbs for 1/16 in I.D. tubing (1/32 in wall max.); manifold mount with X-seal Weight 4.5 g (0.16 oz) PC pins, 4 mm centers Internal volume 0.074 cm3 (0.0045 in3) X-Valve is a registered trademark of Parker Hannifin Corporation. October 2008 / 250 1/4 www.sensortechnics.com X-Valve® 8 mm switching soleniod valves PERFORMANCE CHARACTERISTICS Part no. Pressure Minimum flow Orifice siz es/ Equivalent CV1 Leak rate2 X1... 0...6 psig 4 lpm @ 6 psi 0.045" (1.143 mm)/ 0.018 CV ≤0.16 sccm (FKM, EPDM), ≤0.016 sccm (silicone) X2... 0...30 psig 6 lpm @ 30 psi 0.030" (0.762 mm)/ 0.010 CV ≤0.16 sccm X5... 0...100 psig 9 lpm @ 100 psi 0.020" (0.510 mm)/ 0.005 CV ≤0.2 sccm R esp o n se <20 ms cycling FLOW CURVES (typical air flow)3 Notes: 1 The CV value is the volume flow in US gallons/min under specific flow conditions and describes the relative flow capacity of a valve. If several valves with the same nominal diameter are compared, the valve with the highest CV value has the best flow dynamics design. The equivalent european measure is the kV value expressed in m3/h (kV = 0.86 CV). 2 sccm denotes Standard Cubic Centimeters per Minute. It is a unit for the flow rate at standard conditions of temperature and pressure. 1000 sccm = 1 slpm. 3 slpm denotes Standard Liters per Minute. It is a unit for the flow rate at standard conditions of temperature and pressure. 1 slpm = 1000 sccm. October 2008 / 250 2/4 www.sensortechnics.com X-Valve® 8 mm switching soleniod valves OUTLINE DRAWING Side view 0.28 (7.1) Short pin 0.375 (9.5) Normally closed port Common port 3 x barb fitting for 1/16" I.D. thin wall polyurethane tubing Bottom view 0.916 (23.3) 0.41 (10.3) Long pin Normally open port dimensions in inches (mm) 0.150 (3.8) 0.640 (16.3) 0.100 to receptacle center line (2.5) 0.310 (7.9) 0.157 (4.0) 0.155 (3.9) receptacle contacts for 0.025 (0.6) SQ. terminal posts dimensions in inches (mm) Manifold mount diagram Ø 0.047 x 0.20±0.02 (Ø1.2 x 5.1±0.5) #0-80 UNF-2B x 0.15±0.02 ( 3.8±0.5) 0.315 (8.0) 0.030 (0.8) 0.157 (4.0) 0.5345 (13.58) 0.642 (16.3) 0.315 (8.0) 0.6746 (17.13) Ø 0.090 x "Depth" Ø 0.112/0.115 x 0.100 90° to Ø 0.132±0.003 (Ø 2.3 x "Depth" Ø 2.8/2.9 x 2.5 90° to Ø 3.4±0.08) dimensions in inches (mm) October 2008 / 250 3/4 www.sensortechnics.com X-Valve® 8 mm switching soleniod valves ORDERING INFORMATION Model no. Series Pressure Orifice Options X 1 6 p si 0.045" C oi l wattage Voltage Type 0.5 W universal 03* (1.143 mm) 2 3 0 p si 0.030" 1 0 0 p si 0.020" Elastomer Optional accessories* S short pin F FK M B screw & gasket L long pin E EPD M 0 no accessories (6 & 30 psi only) 1 W universal 05 (0.762 mm) 5 3 V DC Electical connection 5 V DC (6 psi only) (6 psi only) 1 W NC 12 (0.510 mm) 24 12 V D C S silicone (6 psi only) 24 V D C * accessory field not printed on valve Sample order no: X 1 05 L F B Note: Not all combinations might be available. Non-elastomeric versions with enhanced media compatibility are available on request. Please contact your nearest Sensortechnics sales representative for further information. Accessories (please order separately using the following order numbers) Order No. Description ZK071248 Clear transparent polyurethane tubing, inner diameter 1/16 inch (1.6 mm), outer diameter: 1/8 inch (3.2 mm) X-RETAINING CLIP Solder clip for mounting X-PORT PLUG Port plug X-CONNECTOR 12 " leads with connector Sensortechnics reserves the right to make changes to any products herein. Sensortechnics does not assume any liability arising out of the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others. October 2008 / 250 4/4 www.sensortechnics.com