SS-241 R5 AHA 1/24/07 Ceramic Chip Capacitors Type X5R CERTIFIED CERTIFIED 1. General ■ General purpose dielectric for ceramic capacitors ■ EIA class ll dielectric ■ Temperature variation of capacitance is within ±15% from -55°C to +85°C ■ Well suited for decoupling and filtering applications ■ Available in high capacitance values (up to 100 µF) 2. Dimensions Table 1 Dimensions in inches (mm) L Case Size W Solder Plating (Sn) Ni Plating Electrodes d 0402 .02±.004 (0.5±0.1) .021 (0.55) .01±.006 (0.25±0.15) 0603 .063±.006 (1.6±0.15) .032±.006 (0.81±0.15) .035 (0.9) .014±.006 (0.35±0.15) 0805 .079±.008 (2.01±0.2) .049±.008 (1.25±0.2) .051 (1.3) .02±.01 (0.50±0.25) 1206 .126±.008 (3.2±0.2) .063±.008 (1.6±0.2) .059 (1.5) .02±.01 (0.5±0.25) 1210 .126±.008 (3.2±0.2) .098±.008 (2.5±0.2) .067 (1.7) .02±.01 (0.5±0.25) d Ceramic Body L .039±.004 (1.0±0.1) t d Dimensions inches (mm) W t (Max.) Silver Metallization 3. Type Designation The type designation shall be the following form: X5R 0805 A T TD 225 K Dielectric Size Voltage Termination Packaging Capacitance Code Capacitance Tolerance 0402 0603 0805 1206 1210 K = 6.3V A = 10V C = 16V T: Sn TP: 7" 2mm pitch (0402 only) TD: 7" Paper tape TE: 7" Embossed plastic TDB: 13" Paper tape TEB: 13" Embossed plastic 2 significant digits + no. of zeros. K: ±10% PAGE 1 OF 8 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Spec if ica tions giv en h erein m ay be c hanged at any tim e wit hout prior notic e. Pleas e c onf irm tec hnic al s pecif icat ions bef ore y ou order a nd/or use . SS-241 R5 4. X5R Dielectric Capacitance Range Size Available sizes are shaded. 0402 Capacitance values pF µF 6.3 (K) 10 (A) 0603 16 (C) 6.3 (K) 10 (A) 16 (C) 0805 25 (E) 6.3 (K) 10 (A) 1206 16 (C) 25 (E) 6.3 (K) 10 (A) 1210 16 (C) 25 (E) 6.3 (K) 10 (A) 100 150 220 330 470 680 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 0.010 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 3.3 4.7 6.8 10 22 47 100 Capacitance tolerance available: ±10% PAGE 2 OF 8 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Spec if ica tions giv en h erein m ay be c hanged at any tim e wit hout prior notic e. Pleas e c onf irm tec hnic al s pecif icat ions bef ore y ou order a nd/or use . SS-241 R5 5. Characteristics Item Requirement Test Methods Operating Temperature Range -55°C to +85°C Temperature cycle chamber Capacitance Within specified tolerance Dissipation Factor 2.5% for 50V DC rating 5.0% for 10V DC rating Frequency: 1.0 kHz ± 10% Voltage: 1.0 Vrms ± .2 V For Cap > 10 µF, 0.5 Vrms @ 120 Hz Insulation Resistance 100,000 M or 500 M - µF, whichever is less Charge device with rated voltage for 60 ± 5 secs @ room temp/humidity Dielectric Strength No breakdown or visual defects Charge device with 300% of rated voltage for 1-5 seconds, w/charge and discharge current limited to 50 mA (max) Resistance to Flexure Stresses Appearance No defects Deflection: 1 mm Capacitance Variation ± 10% Dissipation Factor Meets initial values Insulation Resistance Initial Value x 0.3 Test Time: 30 seconds 90 mm Solderability 95% of each terminal should be covered with fresh solder Resistance to Solder Heat Appearance Thermal Shock Dip device in eutectic solder at 230 ± 5°C for 5.0 ± 0.5 seconds No defects, < 25% leaching of either end terminal Dip device in eutectic solder at 260°C for Capacitance Variation ± 7.5% 60 seconds. Store at room temperature for 24 ± 2 hours before measuring Dissipation Factor Meets initial values electrical properties Insulation Resistance Meets initial values Dielectric Strength Meets initial values Appearance No visual defects Step 1: -55°C ± 2° 30 ± 3 minutes Capacitance Variation ± 7.5% Step 2: Room temp 3 minutes Dissipation Factor Meets initial values Step 3: +85°C ± 2° 30 ± 3 minutes Insulation Resistance Meets initial values Step 4: Room temp 3 minutes Dielectric Strength Meets initial values Repeat for 5 cycles and measure after 24 ± 2 hours at room temperature PAGE 3 OF 8 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Spec if ica tions giv en h erein m ay be c hanged at any tim e wit hout prior notic e. Pleas e c onf irm tec hnic al s pecif icat ions bef ore y ou order a nd/or use . SS-241 R5 5. Characteristics (continued) Item Requirement Load Life Appearance No visual defects Capacitance Variation ± 12.5% Dissipation Factor Initial value x 2.0 Load Humidity Test Methods Insulation Resistance Initial value x 0.3 Dielectric Strength Meets initial values Appearance No visual defects Capacitance Variation ± 12.5% Dissipation Factor Initial value x 2.0 Insulation Resistance Initial value x 0.3 Dielectric Strength Meets initial values Charge device with twice rated voltage in test chamber set at 85°C ± 2°C for 1000 hours (+48, -0) Remove from test chamber and stabilize at room temp. and humidity for 24 ±2 hours before measuring Store in a test chamber set at 85°C ± 2°C/ 85% ±5% relative humidity for 1000 hours (+48, -0) with rated voltage applied Remove from chamber and stabilize at room temp. and humidity for 24 ±2 hours before measuring 6. Typical Impedance Characteristics X5R - Temperature Coefficient Insulation Resistance vs Temp. +20 10000 +15 +10 +5 0 1000 -5 -10 -15 -20 -60 -40 -20 0 +20 +40 +60 100 +80 +20 Temperature (°C) +25 +40 +60 +80 +100 Temperature (°C) PAGE 4 OF 8 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Spec if ica tions giv en h erein m ay be c hanged at any tim e wit hout prior notic e. Pleas e c onf irm tec hnic al s pecif icat ions bef ore y ou order a nd/or use . SS-241 R5 7. Tape and Reel Quantities All tape and reel specifications are in compliance with RS481. Size Dielectric Voltage Cap. Range TP TD TE TDB TEB 0402 All All All 10000 ––– ––– ––– ––– 0603 All All All ––– 4000 ––– 15000 ––– 0805 X5R All All ––– ––– 3000 ––– ––– 1206 X5R All All ––– ––– 2000 ––– ––– 1210 X5R 10 106 ~ 226 ––– ––– 2000 ––– ––– * TP is a 7" reel with a 2mm pitch, TD & TE are 7" reels, TDB & TEB are 13" reels 8. Reel Dimensions W3 (Includes flange distortion at outer edge). 1.575 (40) min. Access hole at slot location. W2 (Measured at hub). B* (Arbor hole dia.) C D* A N (Hub dia.) Full radius* W1 (Measured at hub). Tape slot in core for tape start. 0.98 (2.5) min. width, .394 (10) min. depth. * Drive spokes optional. If used, asterisked dimensions apply. Tape Size(1) A Max. B* Min. Dimensions in inches (mm) D* Min. C N Min. W2 Max. W1 ± .060 .331 - 0.0 (8.4 ±- 1.0 0.0 ) 8mm 12.992 (330) 0.059 (1.5) 0.512 ± 0.008 (13.0 ± 0.20) .795 (20.2) 1.969 (50) ± .076 12mm .488 - 0.0 (12.4 ±- 2.0 0.0 ) .567 14.4 .724 (18.4) Metric dimensions will govern. English measurements rounded and for reference only. (1) For tape sizes 16mm and 24mm (used with chip size 3640) consult EIA RS-481 latest revision. Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ W3 .311 (7.9 Min.) .429 (10.9 Max.) .469 (11.9 Min.) .607 (15.4 Max.) PAGE 5 OF 8 www.koaspeer.com Spec if ica tions giv en h erein m ay be c hanged at any tim e wit hout prior notic e. Pleas e c onf irm tec hnic al s pecif icat ions bef ore y ou order a nd/or use . SS-241 R5 10 pitches cumulative tolerance on tape ±0.008 (±0.2) 9. Carrier Tape Specifications T2 Embossed plastic 8 & 12mm T P0 Deformation between embossments Embossment P2 D0 E G1 See note 3 A0 B1 K0 Top cover tape F W B0 T1 G2 See note 4 P1 Center lines of cavity For tape feeder reference only including draft concentric around B0 D1 for components .079 x .047 (2.0 x 1.2) and larger Maximum cavity size, see note 1 User direction of feed Tape Size Constant D0 .059 (1.5 8mm and 12mm Tape Size Variable ± ± - E .004 0.0 0.10 0.0 .069 ± .004 ) (1.75 ±0.10) B1 Max. See note 6 D1 Min. See note 5 P0 P2 .157 ± .004 .079 ± .002 (4.0 ± 0.10) (2.0 ± 0.05) F P1 Dimensions in inches (mm) T Max. T1 G1 G2 .024 (0.600) .004 (0.10) Max. .030 (0.75) Min. See note 3 .030 (0.75) Min. See note 4 T2 W A0B0K0 R Min. See note 2 8mm .179 (4.55) .039 (1.0) .138 ± .002 .157 ± .004 (3.5 ± 0.05) (4.0 ± 0.10) .984 (25) .098 (2.5 Max.) 12mm .323 (8.2) .059 (1.5) .217 ± .002 .157 ± .004 (5.5 ± 0.05) (4.0 ± 0.10) 1.181 (30) .256 (6.5 Max.) 12mm 1/2 Pitch .179 (4.55) .039 (1.0) .138 ± .002 .079 ± .004 (3.5 ± 0.05) (2.0 ± 0.10) .984 (25) .098 (2.5 Max.) 12mm Double Pitch .323 (8.2) .059 (1.5) .217 ± .002 .315 ± .004 (5.5 ± 0.05) (8.0 ± 0.10) 1.181 (30) .256 (6.5 Max.) .315 (8.0 ± ± - .012 .004 0.3 0.1 ) See note 1 .472 ± .012 See note 1 (12.0 ± .30) .315 ±- .012 .004 (8.0 ±- 0.3 ) 0.1 See note 1 .472 ± .012 See note 1 (12.0 ± .30) Notes: 1. A0, B0 and K0 are determined by the max. dimensions to the ends of the terminals extending from the components body and/or the body of the component. The clearance between the end of the terminals of the body of the components to the sides and depth of the cavity (A0, B0 and K0) must be within .002" (0.05)mm min. and .020" (0.50)mm max. The clearance allowed must also prevent rotation of the component within the cavity of not more than 20 degrees (see examples A & B). 2. Tape with components shall pass around radius "R" without damage. The minimum trailer length (Note 2 Fig. 3) may require additional length to provide R min. for .472" (12)mm embossed tape for reels with hub diameters approaching N min. (Table 4). 3. G1 dimension is the flat area from the edge of the sprocket hole to either the outward deformation of the carrier tape between the embossed cavities or to the edge of the cavity whichever is less. 4. G2 dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier tape between the embossed cavity or to the edge of the cavity whichever is less. PAGE 6 OF 8 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Spec if ica tions giv en h erein m ay be c hanged at any tim e wit hout prior notic e. Pleas e c onf irm tec hnic al s pecif icat ions bef ore y ou order a nd/or use . SS-241 R5 9. Carrier Tape Specifications (continued) Embossed plastic 8 & 12mm Notes: 5. The embossed hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 20° Maximum Component Rotation 6. B1 dimension is a reference dimension for tape feeder clearance only. 20° Typical component cavity center line BO Maximum Component Rotation Side or Front Sectional View Example "A" Typical component center line AO Top View Example "B" 10 pitches cumulative tolerance on tape ±0.008 (±0.2) 10. Carrier Tape Specifications Punched paper tape 8 & 12mm P2 D0 T E F Top cover tape Bottom cover tape T1 T1 W B0 D0 8mm and 12mm .059 ± .004 - .000 (1.5 ±- 0.1 ) 0.0 Tape Size Variable G1 A0 Cavity size, see note 1 P1 G2 Center lines of cavity User direction of feed Tape Size Constant P0 Dimensions in inches (mm) E P0 P2 T1 G1 G2 R MIN .069 ± .004 (1.75 ±0.10) .157 ± .004 (4.0 ± 0.10) .079 ± .002 (2.0 ± 0.05) .004 (0.10) Max. .030 (0.75) Min. .030 (0.75) Min. .984 (25) See note 2 P1 F W 8mm .157 ± .004 (4.0 ± 0.10) .138 ± .002 (3.5 ± 0.05) .315 ±- .012 .004 (8.0 ±- 0.3 ) 0.1 12mm .157 ± .004 (4.0 ± .010) .217 ± .002 (5.5 ± 0.05) .472 ± .012 (12.0 ± 0.3) 8mm 1/2 Pitch .079 ± .004 (2.0 ± 0.10) .138 ± .002 (3.5 ± 0.05) .315 (8.0 12mm Double Pitch .315 ± .004 (8.0 ± .010) .217 ± .002 (5.5 ± 0.05) .472 ± .012 (12.0 ± 0.3) ± .012 - .004 ± 0.3) - 0.1 A0B0 T See note 1 See note 3 PAGE 7 OF 8 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Spec if ica tions giv en h erein m ay be c hanged at any tim e wit hout prior notic e. Pleas e c onf irm tec hnic al s pecif icat ions bef ore y ou order a nd/or use . SS-241 R5 10. Carrier Tape Specifications (continued) Punched paper tape 8 & 12mm Notes: 1. A0, B0 and T are determined by the max. dimensions to the ends of the terminals extending from the component body and/or the body dimensions of the component. The clearance between the ends of the terminals or body of the components to the sides and depth of the cavity (A0, B0 and T) must be within .002" (0.05) mm min. and .020" (0.50) mm max. The clearance allowed must also prevent rotation of the component 20° Maximum Component Rotation within the cavity of not more than 20 degrees (see examples C & D). 20° Maximum Component Rotation 2. Tape with components shall pass Typical component around radius "R" without damage. cavity center line T B O Typical component 3. .043" (1.1) mm base tape and 20° cavity center line T BO .063" (1.6) mm max. for 20° non-paper base compositions. Maximum Component Rotation Typical component center line Typical AO component center line AO Top View Example "D" Top View Example "D" Maximum Component Side orRotation Front Sectional View "C" Side or Front Sectional Example View Example "C" 11. Recommended Land Pattern Dimensions Component pads should be designed to achieve good solder filets and minimize component movement during reflow soldering. Pad dimensions are given below for multilayer ceramic capacitors for both reflow and wave soldering. The basis for these designs is: • Pad width equal to component width. It is permissible to decrease this to as low as 85% of component width but it is not advisable to go below this. • Pad overlap 0.5mm beneath component • Pad extension 0.5mm beyond components for reflow and 1.0mm for wave soldering Dimensions inches (mm) C D C Case Size A 0402 B 0603 0805 1206 1210 A B C D 0.02 (0.50) 0.03 (0.75) 0.05 (1.25) 0.06 (1.60) 0.10 (2.50) 0.07 (1.70) 0.09 (2.30) 0.12 (3.00) 0.16 (4.00) 0.16 (4.00) 0.02 (0.60) 0.03 (0.80) 0.04 (1.00) 0.04 (1.00) 0.04 (1.00) 0.02 (0.50) 0.03 (0.70) 0.04 (1.00) 0.09 (2.00) 0.09 (2.00) PAGE 8 OF 8 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Spec if ica tions giv en h erein m ay be c hanged at any tim e wit hout prior notic e. Pleas e c onf irm tec hnic al s pecif icat ions bef ore y ou order a nd/or use .