Z01 Standard 1 A Triacs Main Features A2 Symbol Value Unit IT(RMS) 1 A VDRM/VRRM 600 to 800 V IGT (Q1) 3 to 25 mA G A1 A2 G Description A1 The Z01 series is suitable for general purpose AC switching applications. They can be found in applications such as home appliances (electrovalve, pump, door lock, small lamp control), fan speed controllers,... A2 G TO-92 Z01xxA Marking Z01xxA See Ordering information on page 7 Absolute maximum ratings Symbol Parameter RMS on-state current (full sine wave) SOT-223 Ttab = 90° C TO-92 TL = 50° C Non repetitive surge peak on-state current (full cycle, Tj initial = 25° C) F = 50 Hz t = 20 ms F = 60 Hz t = 16.7 ms I²t Value for fusing tp = 10 ms dI/dt Critical rate of rise of on-state current IG = 2 x IGT , tr ≤ 100 ns F = 120 Hz IGM Peak gate current tp = 20 µs ITSM I ²t PG(AV) Tstg Tj SOT-223 Z01xxN Part Number Z01xxN IT(RMS) A2 Order Codes Different gate current sensitivities are available, allowing optimized performances when controlled directly from microcontrollers. Table 1. A1 Unit 1 A 8 A Average gate power dissipation Storage junction temperature range Operating junction temperature range December 2006 Value Rev 8 8.5 0.35 A ²s Tj = 125° C 20 A/µs Tj = 125° C 1 A Tj = 125° C 1 W - 40 to + 150 - 40 to + 125 °C 1/9 www.st.com 9 Characteristcs 1 Z01 Characteristcs Table 2. Electrical characteristics (Tj = 25° C, unless otherwise specified) Z01 Symbol Test Conditions Quadrant Unit I - II - III IGT (1) IV VGT VGD VD = VDRM RL = 3.3 kΩ Tj = 125° C IH (2) IT = 50 mA IL IG = 1.2 IGT (dV/dt)c 09 10 3 5 10 25 5 7 10 25 mA ALL MAX 1.3 V ALL MIN 0.2 V MX. I - III - IV (2) 07 MAX VD = 12 V RL = 30 Ω dV/dt (2) 03 7 10 10 25 7 10 15 25 15 20 25 50 MAX II mA mA VD = 67% VDRM gate open Tj = 110° C MIN 10 20 50 100 V/µs (dI/dt)c = 0.44 A/ms MIN 0.5 1 2 5 V/µs Tj = 110° C 1. minimum IGT is guaranteed at 5% of IGT max. 2. for both polarities of A2 referenced to A1. Table 3. Static characteristics Symbol Test Conditions VTM(1) ITM = 1.4 A Vto (1) Rd (1) IDRM IRRM tp = 380 µs Value Unit Tj = 25° C MAX. 1.56 V Threshold voltage Tj = 125° C MAX. 0.95 V Dynamic resistance Tj = 125° C MAX. 400 mΩ 5 µA 0.5 mA Value Unit Tj = 25° C VDRM = VRRM Tj = 125° C MAX. 1. for both polarities of A2 referenced to A1. Table 4. Thermal resistances Symbol Parameter Rth(j-t) Junction to tab (AC) SOT-223 25 Rth(j-I) Junction to lead (AC) TO-92 60 Rth(j-a) Junction to ambient ° C/W S(1) = 5 cm² SOT-223 1. 2/9 S = Copper surface under tab. 60 ° C/W TO-92 150 Z01 Characteristcs Figure 1. Maximum power dissipation versus RMS on-state current (full cycle) Figure 2. P(W) RMS on-state current versus lead (TO-92) or tab (SOT-223) temperature (full cycle) IT(RMS)(A) 1.50 1.2 1.25 1.0 1.00 0.8 0.75 0.6 0.50 0.4 Rth(j-a) = Rth(j-t) (SOT-223) Rth(j-a) = Rth(j-l) (TO-92) 0.2 0.25 Tl or Ttab(°C) IT(RMS)(A) 0.0 0.00 0.0 0.1 Figure 3. 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 0 1.0 RMS on-state current versus ambient temperature (full cycle) 25 Figure 4. IT(RMS)(A) 50 75 100 125 Relative variation of thermal impedance versus pulse duration K=[Zth(j-a)/Rth(j-a)] 1.2 1.00 1.0 Rth(j-a) = 60°C/W (SOT-223) 0.8 Z01xxA 0.6 0.10 Z01xxN Rth(j-a) = 150°C/W (TO-92) 0.4 0.2 Tamb (°C) tp(s) 0.0 0 25 Figure 5. 50 75 100 125 Relative variation of gate trigger current, holding current and latching current versus junction temperature (typical values) 0.01 1E-3 1E-2 Figure 6. IGT, IH, IL [Tj] / IGT, IH, IL [Tj=25°C] 1E-1 1E+0 1E+1 1E+2 5E+2 Surge peak on-state current versus number of cycles ITSM (A) 2.5 9 8 t=20ms 2.0 7 One cycle Non repetitive Tj initial = 25°C 6 1.5 5 IGT 4 IH & IL 1.0 Repetitive Tamb = 25°C 3 2 0.5 1 Tj (°C) 0.0 -40 -20 0 20 40 60 Number of cycles 0 80 100 120 140 1 10 100 1000 3/9 Characteristcs Figure 7. Z01 Non-repetitive surge peak on-state current for a sinusoidal pulse with width tp < 10 ms and corresponding value of I2t Figure 8. On-state characteristics (maximum values) ITM(A) ITSM (A), I2t (A2s) 10.0 100.0 Tj initial = 25°C dI/dt limitation: 20A/µs ITSM 10.0 Tj = Tjmax. 1.0 1.0 tp (ms) 0.1 0.01 VTM (V) 0.1 0.10 Figure 9. 1.00 10.00 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Relative variation of critical rate Figure 10. Relative variation of critical rate of of decrease of main current versus decrease of main current versus (dV/dt)c (typical values) junction temperature (dI/dt)c [Tj] / (dI/dt)c [Tj Specified] (dI/dt)c [(dV/dt)c] / Specified (dI/dt)c 6 2.6 2.4 2.2 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 5 4 3 2 Z0109 Z0103 Z0107 1 Z0110 (dV/dt)c (V/µs) Tj (°C) 0 0.1 1.0 10.0 100.0 Figure 11. SOT-223 Thermal resistance junction to ambient versus copper surface under tab (printed circuit board FR4, copper thickness: 35 µm) Rth(j-a)(°C/W) 130 120 110 100 90 80 70 60 50 40 30 20 10 0 S(cm²) 0.0 4/9 Tj=max. Vt0=0.95 V Rd=400 mΩ Tj = 25°C I2t 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 0 25 50 75 100 125 Z01 2 Ordering information scheme Ordering information scheme Z 01 03 M A [BLANK] 1AA2 Triac series Current 01 = 1A Sensitivity 03 = 3mA 07 = 5mA 09 = 10mA 10 = 25mA Voltage M = 600V S = 700V N = 800V Package A = TO-92 N = SOT-223 Packing mode 1AA2 = TO-92 Bulk (preferred) 2AL2 = TO-92 Ammopack 5AL2 = TO-92 Tape & reel 5AA4 = SOT-223 Tape & reel Table 5. Product Selector Voltage Part Number 600 V 700 V Sensitivity Type Package 800 V Z0103MA X 3 mA Standard TO-92 Z0103MN X 3 mA Standard SOT-223 Z0103SA X 3 mA Standard TO-92 Z0103SN X 3 mA Standard SOT-223 Z0103NA X 3 mA Standard TO-92 Z0103NN X 3 mA Standard SOT-223 Z0107MA X 5 mA Standard TO-92 Z0107MN X 5 mA Standard SOT-223 Z0107SA X 5 mA Standard TO-92 Z0107SN X 5 mA Standard SOT-223 Z0107NA X 5 mA Standard TO-92 Z0107NN X 5 mA Standard SOT-223 Z0109MA X 10 mA Standard TO-92 Z0109MN X 10 mA Standard SOT-223 Z0109SA X 10 mA Standard TO-92 Z0109SN X 10 mA Standard SOT-223 Z0109NA X 10 mA Standard TO-92 Z0109NN X 10 mA Standard SOT-223 Z0110MA X 25 mA Standard TO-92 Z0110MN X 25 mA Standard SOT-223 Z0110SA X 25 mA Standard TO-92 Z0110SN X 25 mA Standard SOT-223 Z0110NA X 25 mA Standard TO-92 Z0110NN X 25 mA Standard SOT-223 5/9 Packaging information 3 Z01 Packaging information Table 6. SOT-223 Dimensions Dimensions REF. V A A1 c B Millimeters Min. Typ. A Inches Max. Min. Typ. 1.80 Max. 0.071 e1 A1 D B 0.60 0.70 0.80 0.024 0.027 0.031 B1 2.90 3.00 3.10 0.114 0.118 0.122 c 0.24 0.26 0.32 0.009 0.010 0.013 D 6.30 6.50 6.70 0.248 0.256 0.264 0.02 0.001 B1 4 H E 1 2 3 e e 2.3 0.090 e1 4.6 0.181 E 3.30 3.50 3.70 0.130 0.138 0.146 H 6.70 7.00 7.30 0.264 0.276 0.287 V 10° max Figure 12. SOT-223 Footprint dimensions (in millimeters) 3.25 1.32 5.16 7.80 1.32 2.30 6/9 0.95 Z01 Ordering information Table 7. TO-92 Dimensions DIMENSIONS REF. Millimeters Min. Typ. Inches Max. Min. Typ. Max. A a B A 1.35 B C 4.70 C F 4 D E 0.053 0.185 2.54 0.100 D 4.40 0.173 E 12.70 0.500 F 3.70 0.146 a 0.50 0.019 Ordering information Ordering type(1) Marking(1) Package Weight Base quantity Delivery mode Z01xxyA 1AA2 Z01xxyA TO-92 0.2 g 2500 Bulk Z01xxyA 2AL2 Z01xxyA TO-92 0.2 g 2000 Ammopack Z01xxyA 5AL2 Z01xxyA TO-92 0.2 g 2000 Tape and reel Z0103yN 5AA4 Z3y SOT-223 0.12 g 1000 Tape and reel Z0107yN 5AA4 Z7y SOT-223 0.12 g 1000 Tape and reel Z0109yN 5AA4 Z9y SOT-223 0.12 g 1000 Tape and reel 1. xx = sensitivity, y = voltage 7/9 Revision History 5 8/9 Z01 Revision History Date Revision Description of Changes Oct-2001 4 Last update. 10-Feb-2005 5 Package: TO-92 tape and reel delivery mode 5AL2 added. 09-May-2005 6 Table 4 on page 2: typo. mistake corrected 1. (dV/dt)c instead of (dI/dt)c 2. V/µs unit instead of A/ms 21-Apr-2006 7 Reformatted to current standard. Table 2 on page 2: Typo corrected. Values for IGT split into two separate rows. 10-Oct-2006 8 Table 2: modified test conditions for (dV/dt)c. Changed “ambient” to “lead or tab” in Figure 2. Z01 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 9/9