ZARLINK ZL40167DCB

ZL40167
High Output Current
High Speed Dual Operational Amplifier
Data Sheet
Features
•
•
High Output Drive
18.8 Vpp differential output voltage, RL = 50Ω
•
9.4 Vpp single-ended output voltage, RL = 25Ω
•
•
ZL40167/DCA (tubes) 8 lead SOIC
ZL40167/DCB (tape and reel) 8 lead SOIC
High Output Current
-40°C to +85°C
± 200mA @ Vo = 9.4 Vpp, Vs = 12V
•
Low Distortion
•
•
Ordering Information
•
•
•
September 2003
High ESD (Electro-Static Discharge) immunity
•
85dB SFDR (Spurious Free Dynamic Range)
@ 100KHz, Vo = 2Vpp, RL = 25Ω
•
High Speed
Low differential gain and phase
•
•
192MHz 3dB bandwidth (G=2)
•
240V / µs slew rate
4kV for Supply and Output pins
0.005% and -0.07deg
Applications
Low Noise
•
ADSL PCI modem cards
•
3.8nV / √Hz: input noise voltage
•
xDSL external modem
•
2.7pA / √Hz: input noise current
•
Line Driver
Low supply current: 7mA/amp
•
Single-supply operation: 5V to 12V
Out_1
8 V+
1
In_n_1 2
7 Out_2
1
In_p_1 3
6 In_n_2
2
V- 4
ZL40167
5 In_p_2
Figure 1 - Functional Block Diagram and Pin Connection
1
Zarlink Semiconductor Inc.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright 2003, Zarlink Semiconductor Inc. All Rights Reserved.
ZL40167
Data Sheet
Description
The ZL40167 is a low cost voltage feedback opamp capable of driving signals to within 1V of the power supply rails.
It features low noise and low distortion accompanied by a high output current which makes it ideally suited for the
application as an xDSL line driver. The dual opamp can be connected as a differential line driver delivering signals
up to 18.8Vpp swing into a 25Ω load, fully supporting the peak upstream power levels for upstream full-rate ADSL
(Asymmetrical Digital Subscriber Line).
The wide bandwidth, high power output and low differential gain and phase figures make the ZL40167 ideally suited
for a wide variety of video driver applications.
Application Notes
The ZL40167 is a high speed, high output current, dual operational amplifier with a high slew rate and low
distortion. The device uses conventional voltage feedback for ease of use and more flexibility. These characteristics
make the ZL40167 ideal for applications where driving low impedances of 25 to 100Ω such as xDSL and active
filters.
The figure below shows a typical ADSL application utilising a 1:2 transformer, the feedback path provides a
Gain = +2.
12R5
Rf1
Rg
100R
Rf2
12R5
Figure 2 - A Typical ADSL Application
A class AB output stage allows the ZL40167 to deliver high currents to low impedance loads with low distortion
while consuming low quiescent current.
Note: the high ESD immunity figure of 4kV may mean that in some designs fewer additional EMC protection
components are needed thus reducing total system costs.
The ZL40167 is not limited to ADSL applications and can be used as a general purpose opamp configured with
either inverting or non-inverting feedback. The figure below shows non-inverting feedback arrangement that has
typically been used to obtain the data sheet specifications.
2
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Rf
Rg
Figure 3 - A Non-Inverting Feedback Amplifier Example
Video transmitter and receiver for twisted wire pair
Composite video signals can be transmitted down twisted pair cable, i.e. Ethernet (CAT 5), using a differential
transmitter and receiver. The transmitter must be able to drive high currents into the low impedance twisted pair
cable. For video, the amplifiers require flat gain and low phase-shift over the video signal band. To ensure this, the
amplifiers will have 3dB bandwidths well in excess of this. The ZL40167 (dual amplifier) has all of these attributes.
With reference to the differential video driver shown in Figure , the input coax is assumed to have a characteristic
impedance of 75 Ohms, this is terminated with a parallel combination of 110 Ohms and the input impedance of
amplifier IC1 (b) of 255 Ohms, giving 77 Ohms. Low values of feedback resistors are used around the op-amps to
reduce phase-shift due to parasitic capacitors and to minimise the addition of noise.
Baseband PAL or NTSC video signals generally have an amplitude of 2V pk-pk. A gain of two is used to ensure that
the signal level at the end of the (terminated with 100 Ohms) differential pair will be the same as the input level,
neglecting any losses due to the use of long cable lengths.
Composite Video
Co-Ax Input
IC1(a)
50R
110R
510R
510R
Twisted Pair
Output
510R
510R
50R
510R
IC1(b)
Figure 4 - Differential Video Driver
The differential receiver is shown in Figure 5 has a 100 Ohm line termination resistor, followed by a differential
amplifier. Long cables will tend to attenuate the signal with greater losses at the higher frequencies, so the second
amplifier is used to equalise these losses. Initially the amplifier should be built without fitting components R1 and
3
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
C1. Select the value of R2 to give the required gain at low frequency. Adjust the values of R1 and C1 to correct for
the frequency dependant attenuation of the cable.
To drive a coax cable the output of the amplifier is connected via a series matching 75 Ohm resistor, again this
second (dual amplifier) ZL40167 provides the required power output for the restored 2Vpk-pk video signal.
510R
510R
Twisted Pair
Input
IC2(a)
100R
510R
510R
R2
C1
Composite Video
Co-Ax Output
R1
IC2(b)
75R
510R
Figure 5 - Differential Video Receiver
4
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Absolute Maximum Ratings - (See Note 1)
Parameter
Max
Units
VIN
±1.2
V
Output Short Circuit Protection
VOS/C
See Apps
Note in this
data sheet
Supply Voltage
V+, V-
±13.2
V
(V+) +0.8
V
±5.5
V
4
(Note 3)
kV
-55
+150
°C
Latch-up test
+/-100mA
for 100ms
(Note 4)
Supply transient test
20% pulse
for 100ms
(Note 5)
Vin Differential
Voltage at Input Pins
Voltage at Output Pins
Symbol
V(+IN), V(-IN)
Storage Temperature
Note 2:
Note 3:
Note 4:
Note 5:
(V-) -0.8
VO
ESD Protection (HBM Human Body Model)
(See Note 2)
Note 1:
Min
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate
conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed
specifications and the test conditions, see the Electrical Characteristics.
Human body model, 1.5kΩ in series with 100pF. Machine model, 200Ω in series with 100pF.
1.25kV between the pairs of +INA, -INA and +INB, -INB pins only. 4kV between supply pins, OUTA or OUTB pins and any
input pin.
+/-100mA applied to input and output pins to force the device to go into “latch-up”. The device passes this test to JEDEC spec
17.
Positive and Negative supply transient testing increases the supplies by 20% for 100ms.
Operating Ratings - (See Note 1)
Parameter
Supply Voltage
Symbol
Min
Max
Units
V+, V-
± 2.5
±6.5
V
-40
150
°C
Junction Temperature Range
Junction to Ambient Resistance
Rth(j-a)
150
°C
4 layer FR5
board
Junction to Case Resistance
Rth(j-c)
60
°C
4 layer FR5
board
Note 1:
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate
conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed
specifications and the test conditions, see the Electrical Characteristics.
5
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Electrical Characteristics - TA = 25°C, G = +2, Vs = ± 6V, Rf = Rg = 510Ω, RL = 100Ω / 2pF; Unless
otherwise specified.
Symbol
Parameter
Min
(Note 1)
Conditions
Typ
(Note 2)
Max
(Note 3)
Units
Test
Type
Dynamic Performance
-3dB Bandwidth
Vo = 200mVp-p
192
MHz
C
-0.1dB Bandwidth
Vo = 200mVp-p
32
MHz
C
Slew Rate
4V Step O/P, 10-90%
240
V/µs
C
Rise and Fall Time
4V Step O/P, 10-90%
13.3
ns
C
Rise and Fall Time
200mV Step O/P,
10-90%
1.7
ns
C
Differential Gain
NTSC, RL = 150Ω
0.005
%
C
Differential Phase
NTSC, RL = 150Ω
-0.07
deg
C
Vo = 8.4Vpp,
f =100KHz,RL= 25Ω/2pF
-65.4
dBc
C
Vo = 8.4Vpp,
f =1MHz,RL = 100Ω/2pF
-83.8
dBc
C
Vo = 2Vpp,
f =100kHz,RL= 25Ω/2pF
-93.6
dBc
C
Vo = 2Vpp,
f =1MHz,RL =100Ω/2pF
-86
dBc
C
Vo = 8.4Vpp,
f =100KHz,RL=25Ω/2pF
-70
dBc
C
Vo = 8.4Vpp,
f =1MHz,RL =100Ω/2pF
-77.7
dBc
C
Vo = 2Vpp,
f =100KHz,RL=25Ω/2pF
-85
dBc
C
Vo = 2Vpp,
f =1MHz,RL=100Ω/2pF
-73.5
dBc
C
-75
dBc
C
69 KHz
-76.3
dBc
C
90.5625 KHz
-73.8
dBc
C
112.125 KHz
-71.5
dBc
C
Input Noise Voltage
f = 100KHz
3.85
nV/√Hz
C
Input Noise Current
f = 100KHz
2.7
pA/√Hz
C
Distortion and Noise Response
2nd Harmonic
Distortion
3rd Harmonic
Distortion
MTPR
Multi-Tone Power
Ratio
47.4375 KHz
6
Zarlink Semiconductor Inc.
ZL40167
Symbol
Parameter
Conditions
Data Sheet
Min
(Note 1)
Typ
(Note 2)
Max
(Note 3)
Units
Test
Type
- 4.2
- 0.3
4.2
mV
A
-10
-20
µA
A
-0.2
2
µA
A
4.9
V
A
Input Characteristics
Vos
Input Offset Voltage
Tj = -40°C to 150°C
Ib
Input Bias Current
Tj = -40°C to 150°C
Ios
Input Offset Current
Tj = -40°C to 150°C
-2
CMVR
Common Mode
Voltage Range
Tj = -40°C to 150°C
- 4.9
CMRR
Common Mode
Rejection Ratio
Tj = -40°C to 150°C
70
79
dB
A
RL = 1k,
Tj = -40°C to 150°C
4.7
10
V/mV
A
RL = 25Ω,
Tj = -40°C to 150°C
1.6
5.5
Output Swing
RL = 25Ω,
Tj = -40°C to 150°C
- 4.5
± 4.7
4.5
V
A
Output Swing
RL = 1k,
Tj = -40°C to 150°C
-5
± 5.1
5
V
A
Output Current
(Note 3)
Vo = 0,
Tj = -40°C to 150°C
570
1000
mA
B
mA
A
dB
A
Transfer Characteristics
Avol
Isc
Voltage Gain
A
Power Supply
Is
Supply
Current / Amp
Tj = -40°C to 150°C
PSRR
Power Supply
Rejection Ratio
Tj = -40°C to 150°C
7
73
9
81
Note 1:
The maximum power dissipation is a function of Tj(max), θJA and TA. The maximum allowable power dissipation at any
ambient temperature is PD = (Tj(max) - TA)/ θJA. All numbers apply for packages soldered directly onto a PC board.
Note 2:
Typical values represent the most likely parametric norm.
Note 3: Test Types:
a. 100% tested at 25°C. Over temperature limits are set by characterisation, simulation and statistical analysis.
b. Limits set by characterisation, simulation and statistical analysis.
c. Typical value only for information.
7
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
± 2.5V Electrical Characteristics - TA = 25°C, G = +2, Vs = ± 2.5V, Rf = Rg = 510Ω, RL = 100Ω / 2pF; Unless
otherwise specified.
Symbol
Parameter
Min
(Note 1)
Conditions
Typ
(Note 2)
Max
(Note 3)
Units
Test
Type
Dynamic Performance
-3dB Bandwidth
176.5
MHz
C
-0.1dB Bandwidth
83.8
MHz
C
Slew Rate
1V Step O/P, 10-90%
216
V/µs
C
Rise and Fall Time
1V Step O/P, 10-90%
3.7
ns
C
Rise and Fall Time
200mV Step O/P,
10-90%
1.7
ns
C
-92.6
dBc
C
-85
dBc
C
Vo = 2Vpp, f = 100KHz,
RL = 25Ω
-86.3
dBc
C
Vo = 2Vpp, f = 1MHz,
RL = 100Ω
-74.8
dBc
C
Distortion and Noise Response
2nd Harmonic
Distortion
Vo = 2Vpp,f = 100KHz,
RL = 25Ω
Vo = 2Vpp, f = 1MHz,
RL = 100Ω
3rd Harmonic
Distortion
Input Characteristics
Vos
Input Offset Voltage
Tj = -40°C to 150°C
Ib
Input Bias Current
Tj = -40°C to 150°C
CMVR
Common Mode
Voltage Range
CMRR
Common Mode
Rejection Ratio
- 4.2
- 0.3
4.2
mV
B
- 10
-20
µA
B
1.55
V
B
-1.55
Tj = -40°C to 150°C
70
80
dB
B
RL = 1k, Tj = -40°C to
150°C
5.5
10.5
V/mV
B
RL = 25Ω, Tj = -40°C to
150°C
1.6
5.8
RL = 25Ω, Tj = -40°C to
150°C
-1.4
±1.45
1.4
RL = 1k, Tj = -40°C to
150°C
-1.6
±1.65
1.6
Transfer Characteristics
Avol
Voltage Gain
B
Output Characteristics
Output Swing
8
Zarlink Semiconductor Inc.
V
B
B
ZL40167
Symbol
Parameter
Data Sheet
Min
(Note 1)
Conditions
Typ
(Note 2)
Max
(Note 3)
Units
Test
Type
6.75
8.5
mA
A
dB
B
Power Supply
Is
Supply
Current/Amp
Tj = -40°C to 150°C
PSRR
Power Supply
Rejection Ratio
Tj = -40°C to 150°C
73
83
Note 1:
The maximum power dissipation is a function of Tj(max), θJA and TA. The maximum allowable power dissipation at any
ambient temperature is PD = (Tj(max) - TA)/ θJA. All numbers apply for packages soldered directly onto a PC board.
Note 2:
Typical values represent the most likely parametric norm.
Note 3: Test Types:
a. 100% tested at 25°C. Over temperature limits are set by characterisation, simulation and statistical analysis.
b. Limits set by characterisation, simulation and statistical analysis.
c. Typical value only for information.
9
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100,Vs = 6V. Unless
otherwise specified.
Output Sw ing
12.0
Vout Swing (V)
10.0
8.0
R L = 1K
6.0
RL = 25
4.0
2.0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
+/- Supply (V)
Figure 6 - Output Swing
Positive Output Sw ing into 1Kohm s
1.0
0.9
- 40 C
Vsupply - Vout (V)
0.8
25 C
0.7
0.6
85 C
0.5
0.4
0.3
0.2
0.1
0.0
1.0
2.0
3.0
4.0
5.0
+/- Supply (V)
Figure 7 - Positive Output Swing into 1KΩ
10
Zarlink Semiconductor Inc.
6.0
7.0
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Negative Output Sw ing into 1Kohm s
1.0
- 40 C
0.9
25 C
Vout - Vsupply (V)
0.8
85 C
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
6.0
7.0
+/- Supply (V)
Figure 8 - Negative Output Swing into 1KΩ
Positive Output Sw ing into 25 ohm s
1.4
1.2
-40 C
25 C
Vsupply - Vout (V)
1.0
0.8
85 C
0.6
0.4
0.2
0.0
1.0
2.0
3.0
4.0
5.0
+/- Supply (V)
Figure 9 - Positive Output Swing into 25Ω
11
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Negative Output Sw ing into 25 ohm s
1.4
1.2
25 C
- 40 C
Vout - Vsupply (V)
1.0
85 C
0.8
0.6
0.4
0.2
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
+/- Supply (V)
Figure 10 - Negative Output Swing into 25Ω
+Vout vs. ILoad
5.4
5.3
5.2
+Vout (V)
85 C
5.1
25 C
5.0
4.9
- 40 C
4.8
4.7
4.6
0.00
0.05
0.10
0.15
ILoad (A)
Figure 11 - +Vout vs. lLoad
12
Zarlink Semiconductor Inc.
0.20
0.25
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
-Vout vs. ILoad
5.4
5.3
5.2
-Vout (V)
5.1
85 C
5.0
25 C
4.9
- 40 C
4.8
4.7
4.6
0.00
0.05
0.10
0.15
0.20
0.25
ILoad (A)
Figure 12 - -Vout vs. lLoad
+Vout vs. ILoad, VS = 2.5V
2.0
1.9
1.8
25 C
+Vout (V)
1.7
85 C
1.6
1.5
1.4
- 40 C
1.3
1.2
1.1
1.0
0.00
0.05
0.10
0.15
ILoad (A)
Figure 13 - +Vout vs. lLoad, Vs = ±2.5V
13
Zarlink Semiconductor Inc.
0.20
0.25
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
-Vout vs. ILoad, VS = 2.5V
2.0
1.9
1.8
25 C
85 C
1.6
1.5
1.4
-40 C
1.3
1.2
1.1
1.0
0.00
0.05
0.10
0.15
0.20
0.25
ILoad (A)
Figure 14 - -Vout vs. lLoad, Vs ±2.5V
Vout vs. RLoad
5.5
85 C
5.0
25 C
-40 C
4.5
Vout (V)
-Vout (V)
1.7
4.0
3.5
3.0
0
10
20
30
40
50
60
70
RLoad (ohms)
Figure 15 - Vout vs Rload
14
Zarlink Semiconductor Inc.
80
90
100
110
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Supply Current
16.0E-3
25 C
Supply Current (A)
14.0E-3
85 C
12.0E-3
- 40 C
10.0E-3
8.0E-3
6.0E-3
4.0E-3
2.0E-3
000.0E+0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
+/- Supply (V)
Figure 16 - Supply Current vs. Supply Voltage
Source Current, Vo = 0V
1.4
25 C
1.2
- 40 C
Current (A)
1.0
85 C
0.8
0.6
0.4
0.2
0.0
0.0
1.0
2.0
3.0
4.0
5.0
+/- Supply (V)
Figure 17 - Sourcing Current vs. Supply Voltage
15
Zarlink Semiconductor Inc.
6.0
7.0
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Sinking Current, Vo = 0V
1.2
- 40 C
25 C
1.0
85 C
Current (A)
0.8
0.6
0.4
0.2
0.0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
+/- Supply (V)
Figure 18 - Sinking Current vs. Supply Voltage
Vos vs. VS
140.0E- 6
120.0E- 6
100.0E- 6
Vos (V)
85 C
80.0E- 6
- 40 C
60.0E- 6
25 C
40.0E- 6
20.0E- 6
000.0E+0
2.0
2.5
3.0
3.5
4.0
4.5
5.0
+/- Supply (V)
Figure 19 - Vos vs. VS
16
Zarlink Semiconductor Inc.
5.5
6.0
6.5
7.0
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Vos vs Vcm
7.0E-3
6.0E-3
Vos (V)
5.0E-3
4.0E-3
3.0E-3
2.0E-3
85 C
1.0E-3
- 40 C
000.0E+0
0.0
1.0
2.0
3.0
25 C
4.0
5.0
6.0
Vcm (V)
Figure 20 - Vos vs. Vcm
Vos vs. Vcm , VS = +/- 2.5V
600.0E-6
500.0E-6
Vos (V)
400.0E-6
25 C
300.0E-6
85 C
200.0E-6
-40 C
100.0E-6
000.0E+0
0.0
0.2
0.4
0.6
0.8
1.0
Vcm (V)
Figure 21 - Vos vs. Vcm, Vs = ±2.5V
17
Zarlink Semiconductor Inc.
1.2
1.4
1.6
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Bias Current vs. Vsupply
-4.0E- 6
-4.5E- 6
-5.0E- 6
-5.5E- 6
Current (A)
- 40 C
-6.0E- 6
-6.5E- 6
25 C
-7.0E- 6
-7.5E- 6
85 C
-8.0E- 6
-8.5E- 6
-9.0E- 6
1.0
2.0
3.0
4.0
5.0
6.0
7.0
6.0
7.0
+/- Supply (V)
Figure 22 - Bias Current vs. Vsupply
Offset Current vs. Vsupply
25.0E- 9
20.0E- 9
Current (A)
85 C
15.0E- 9
10.0E- 9
25 C
- 40 C
5.0E-9
000.0E+0
1.0
2.0
3.0
4.0
5.0
+/- Supply (V)
Figure 23 - Offset Current vs. Vsupply
18
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Harm onic Distortion vs. Load
F = 1MHz, Vout = 2Vpp
-60
Harmonic Distortion (dBc)
-65
-70
3 r d Ha r moni c
-75
-80
-85
-90
2 nd H a r moni c
-95
-100
-105
0
50
100
150
200
250
300
350
400
450
500
Load Resistance (ohm s)
Figure 24 - Harmonic Distortion vs. Load F = 1MHZ, Vout = 2Vpp
Harm onic Distortion vs. Load
VS = +/- 2.5V, F = 1MHz, Vout = 2Vpp
-60
Harmonic Distortion (dBc)
-65
-70
-75
3 r d H a r moni c
-80
-85
2 nd Ha r moni c
-90
-95
-100
-105
0
50
100
150
200
250
300
350
400
450
500
Load Resistance (ohm s)
Figure 25 - Harmonic Distortion vs. Load Vs = ±2.5V, F = 1MHz, Vout = 2Vpp
19
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Harm onic Distortion vs. Output Voltage
VS = +/- 2.5V, F = 1MHz
Harmonic Distortion (dBc)
- 40
- 50
- 60
3 r d H a r m o ni c
- 70
- 80
- 90
2 n d H a r m o ni c
-100
-110
0.0
0.5
1.0
1.5
2.0
2.5
3.0
Output Voltage (Vpp)
Figure 26 - Harmonic Distortion vs. Output Voltage Vs = ±2.5V, F = 1MHz
Harm onic Distortion vs. Output Voltage
F = 1MHz
Harmonic Distortion (dBc)
-40
-50
-60
3 r d Ha r moni c
-70
-80
2 nd H a r moni c
-90
-100
-110
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
Output Voltage (Vpp)
Figure 27 - Harmonic Distortion vs. Output Voltage F = 1MHz
20
Zarlink Semiconductor Inc.
10.0
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Harm onic Distortion vs. Output Voltage
VS = +/- 2.5V, F = 1MHz, RL = 25ohm s
Harmonic Distortion (dBc)
-40
-50
3 r d Ha r moni c
-60
-70
2 n d H a r m on i c
-80
-90
-100
0.0
0.5
1.0
1.5
2.0
2.5
3.0
Output Voltage (Vpp)
Figure 28 - Harmonic Distortion vs. Output Voltage Vs = ±2.5V, F = 1MHz, RL = 25Ω
Harm onic Distortion vs. Output Voltage
F = 1MHz, RL = 25ohm s
Harmonic Distortion (dBc)
-40
-50
2 n d H a r m on i c
-60
-70
3 r d Ha r moni c
-80
-90
-100
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
Output Voltage (Vpp)
Figure 29 - Harmonic Distortion vs. Output Voltage F = 1MHz, RL = 25Ω
21
Zarlink Semiconductor Inc.
10.0
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Harm onic Distortion vs. Output Voltage
F = 10MHz
Harmonic Distortion (dBc)
-20
-30
3 r d H a r m on i c
-40
-50
2 n d H a r m on i c
-60
-70
-80
-90
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
Output Voltage (Vpp)
Figure 30 - Harmonic Distortion vs. Output Voltage F = 10MHz
Harm onic Distortion vs. Output Voltage
F = 10MHz, RL = 25ohm s
Harmonic Distortion (dBc)
-20
-30
3 r d Ha r moni c
-40
-50
2 nd Ha r moni c
-60
-70
-80
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
Output Voltage (Vpp)
Figure 31 - Harmonic Distortion vs. Output Voltage F = 10MHz, RL = 25Ω
22
Zarlink Semiconductor Inc.
10.0
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Harm onic Distortion vs. Frequency
Vout = 2Vpp
- 30
Harmonic Distortion (dBc)
- 40
- 50
- 60
3 r d H a r moni c
- 70
- 80
2 nd H a r moni c
- 90
-100
- 110
-120
100.0E+3
1.0E+6
10.0E+6
Frequency (Hz)
Figure 32 - Harmonic Distortion vs. Frequency Vout = 2Vpp
Harm onic Distortion vs. Output Voltage
VS = +/- 2.5V, F=10MHz
Harmonic Distortion (dBc)
- 30
- 40
3 r d Ha r moni c
- 50
- 60
2 nd Ha r moni c
- 70
- 80
- 90
0.0
0.5
1.0
1.5
2.0
2.5
Output Voltage (Vpp)
Figure 33 - Harmonic Distortion vs. Output Voltage Vs = ±2.5V, F = 10MHz
23
Zarlink Semiconductor Inc.
3.0
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Harm onic Distortion vs. Frequency
Vout = 2Vpp, RL = 25ohm s
-30
Harmonic Distortion (dBc)
-40
-50
3 r d Ha r moni c
-60
-70
2 n d H a r m on i c
-80
-90
-100
-110
100.0E+3
1.0E+6
10.0E+6
Frequency (Hz)
Figure 34 - Harmonic Distortion vs. Frequency Vout = 2Vpp, RL = 25Ω
Harm onic Distortion vs. Output Voltage
VS = +/- 2.5V, F = 10MHz, RL = 25 ohm s
Harmonic Distortion (dBc)
-20
-30
3 r d H a r moni c
-40
-50
2 nd H a r moni c
-60
-70
-80
0.0
0.5
1.0
1.5
2.0
2.5
3.0
Output Voltage (Vpp)
Figure 35 - Harmonic Distortion vs. Output Voltage Vs = ±2.5V, F = 10MHz, RL = 25Ω
24
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Harm onic Distortion vs. Frequency
VS = +/- 2.5V, Vout = 2Vpp
-30
-50
-60
3 r d H a r m on i c
-70
-80
2 nd Ha r moni c
-90
-100
-110
-120
100.0E+3
1.0E+6
10.0E+6
Frequency (Hz)
Figure 36 - Harmonic Distortion vs. Frequency Vs = ±2.5V, Vout = 2Vpp
Harm onic Distortion vs. Frequency
VS = +/- 2.5V, Vout = 2Vpp, RL = 25ohm s
- 30
- 40
Harmonic Distortion (dBc)
Harmonic Distortion (dBc)
-40
- 50
3 r d H a r m o ni c
- 60
- 70
2 nd H a r m o ni c
- 80
- 90
-100
- 110
100.0E+3
1.0E+6
10.0E+6
Frequency (Hz)
Figure 37 - Harmonic Distortion vs. Frequency Vs = ±2.5V, Vout = 2Vpp, RL = 25Ω
25
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Small Signal Frequency Response
25.0
G = 10
20.0
15.0
Gain (dB)
G=5
10.0
5.0
G=2
0.0
-5.0
-10.0
1.0E+3
10.0E+3
100.0E+3
1.0E+6
10.0E+6
100.0E+6
1.0E+9
Frequency (Hz)
Figure 38 - Small Signal Frequency Response
Frequency Response, Vo = 200mVpp
8.0
VS = 12V
6.0
Gain (dB)
4.0
2.0
VS = 5V
0.0
-2.0
-4.0
-6.0
100.0E+3
1.0E+6
10.0E+6
100.0E+6
Frequency (Hz)
Figure 39 - Frequency Response, VO = 200mVpp
26
Zarlink Semiconductor Inc.
1.0E+9
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Pulse Response
2.5
2.0
Output Voltage (V)
1.5
1.0
0.5
0.0
-0.5
-1.0
-1.5
-2.0
-2.5
5.4E- 6
5.5E-6
5.6E-6
5.7E-6
5.8E-6
5.9E-6
6.0E-6
6.1E-6
Tim e (s)
Figure 40 - Pulse Response
Pulse Response, VS = +/- 2.5V
0.6
Output Voltage (V)
0.4
0.2
0.0
-0.2
-0.4
-0.6
5.4E-6
5.5E-6
5.6E-6
5.7E-6
5.8E-6
5.9E-6
Tim e (s)
Figure 41 - Pulse Response, Vs = ±2.5V
27
Zarlink Semiconductor Inc.
6.0E-6
6.1E-6
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
PSRR vs. Frequency
100
90
80
70
PSRR (dB)
60
50
40
30
20
10
0
10.0E+0
100.0E+0
1.0E+3
10.0E+3
100.0E+3
1.0E+6
10.0E+6
Frequency (Hz)
Figure 42 - PSRR vs Frequency
CMRR vs. Frequency
90
80
70
CMRR (dB)
60
50
40
30
20
10
0
10.0E+0
100.0E+0
1.0E+3
10.0E+3
100.0E+3
Frequency (Hz)
Figure 43 - CMRR vs. Frequency
28
Zarlink Semiconductor Inc.
1.0E+6
10.0E+6
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
PSRR vs. Frequency
VS = +/- 2.5V
100
90
80
PSRR (dB)
70
60
50
40
30
20
10
0
10.0E+0
100.0E+0
1.0E+3
10.0E+3
100.0E+3
1.0E+6
10.0E+6
1.0E+6
10.0E+6
Frequency (Hz)
Figure 44 - PSRR vs. Frequency Vs = ±2.5V
CMRR vs. Frequency
VS = +/- 2.5V
90
80
CMRR (dB)
70
60
50
40
30
20
10
0
10.0E+0
100.0E+0
1.0E+3
10.0E+3
100.0E+3
Frequency (Hz)
Figure 45 - CMRR vs. Frequency Vs = ±2.5V
29
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Input Noise Voltage vs. Frequency
3.85E-09
Voltage Noise (V/sqrt(Hz))
3.80E-09
3.75E-09
3.70E-09
VS =+ / - 2 . 5 V
3.65E-09
3.60E-09
VS =+ / - 6 V
3.55E-09
100.0E+0
1.0E+3
10.0E+3
100.0E+3
1.0E+6
10.0E+6
Frequency (Hz)
Figure 46 - Noise Voltage vs. Frequency
Input Current Noise vs. Frequency
4.0E-12
3.8E-12
Current Noise (A/sqrt(Hz))
3.6E-12
3.4E-12
3.2E-12
3.0E-12
VS=+/-2.5V
2.8E-12
2.6E-12
VS=+/-6V
2.4E-12
2.2E-12
2.0E-12
100.0E+0
1.0E+3
10.0E+3
100.0E+3
1.0E+6
Frequency (Hz)
Figure 47 - Current Noise vs. Frequency
30
Zarlink Semiconductor Inc.
10.0E+6
For more information about all Zarlink products
visit our Web Site at
www.zarlink.com
Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively “Zarlink”) is believed to be reliable.
However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such
information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or
use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual
property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in
certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink.
This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part
of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other
information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the
capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute
any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and
suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does
not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in
significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink’s conditions of sale which are available on request.
Purchase of Zarlink’s I2C components conveys a licence under the Philips I2C Patent rights to use these components in and I2C System, provided that the system
conforms to the I2C Standard Specification as defined by Philips.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright Zarlink Semiconductor Inc. All Rights Reserved.
TECHNICAL DOCUMENTATION - NOT FOR RESALE