HFA1110 ® Data Sheet June 6, 2006 750MHz, Low Distortion Unity Gain, Closed Loop Buffer FN2944.8 Features • Wide -3dB Bandwidth. . . . . . . . . . . . . . . . . . . . . . 750MHz The HFA1110 is a unity gain closed loop buffer that achieves -3dB bandwidth of 750MHz, while offering excellent video performance and low distortion. Manufactured on Intersil’s proprietary complementary bipolar UHF-1 process, the HFA1110 also offers very fast slew rate, and high output current. It is one more example of Intersil’s intent to enhance its leadership position in products for high speed signal processing applications. The HFA1110’s settling time of 11ns to 0.1%, low distortion and ability to drive capacitive loads make it an ideal flash A/D driver. The HFA1110 is an enhanced, pin compatible upgrade for the AD9620, AD9630, CLC110, EL2072, BUF600 and BUF601. For buffer applications requiring a standard op amp pinout, or selectable gain (-1, +1, +2), see the HFA1112 data sheet. For output limiting see the HFA1113 data sheet. For military grade product please refer to the HFA1110/883 data sheet. • Very Fast Slew Rate. . . . . . . . . . . . . . . . . . . . . . 1300V/µs • Fast Settling Time (0.2%). . . . . . . . . . . . . . . . . . . . . . 7ns • High Output Current . . . . . . . . . . . . . . . . . . . . . . . . . 60mA • Fixed Gain of +1 • Gain Flatness (100MHz) . . . . . . . . . . . . . . . . . . . . 0.03dB • Differential Phase . . . . . . . . . . . . . . . . . . . . . . . . . . 0.025° • Differential Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.04% • 3rd Harmonic Distortion (50MHz). . . . . . . . . . . . . . -80dBc • 3rd Order Intercept (100MHz) . . . . . . . . . . . . . . . . 30dBm • Pb-Free Plus Anneal Available (RoHS Compliant) Applications • Video Switching and Routing • RF/IF Processors • Driving Flash A/D Converters • High-Speed Communications Pinout • Impedance Transformation HFA1110 (SOIC) TOP VIEW V+ 1 OPT V+ 2 NC IN • Line Driving • Radar Systems 8 OUT 7 NC 3 6 OPT V- 4 5 V- - + Ordering Information PART NUMBER PART TEMP. MARKING RANGE (°C) PACKAGE PKG. DWG. # HFA1110IB 1110IB -40 to 85 8 Ld SOIC M8.15 HFA1110IBZ (Note) 1110IBZ -40 to 85 8 Ld SOIC (Pb-free) M8.15 HFA1110EVAL High Speed Buffer DIP Evaluation Board Pin Descriptions NAME PIN NUMBER V+ 1 Positive Supply Opt V+ 2 Optional Positive Supply NC 3 No Connection IN 4 Input V- 5 Negative Supply Opt V- 6 Optional Negative Supply NC 7 No Connection OUT 8 Output DESCRIPTION 1 NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2000, 2006. All Rights Reserved All other trademarks mentioned are the property of their respective owners. HFA1110 Absolute Maximum Ratings Thermal Information Voltage Between V+ and V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12V DC Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VSUPPLY Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60mA Thermal Resistance (Typical, Note 1) Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C θJA (°C/W) SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158 Maximum Junction Temperature (Plastic Package) . . . . . . . . 150°C Maximum Storage Temperature Range . . . . . . . . . . -65°C to 150°C Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C (SOIC - Lead Tips Only) CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. θJA is measured with the component mounted on an evaluation PC board in free air. VSUPPLY = ±5V, RL = 100Ω, Unless Otherwise Specified Electrical Specifications PARAMETER TEST CONDITIONS TEMP (°C) MIN TYP MAX UNITS Output Offset Voltage (Note 2) 25 - 8 25 mV Full - - 35 mV Output Offset Voltage Drift Full - 10 - µV/°C INPUT CHARACTERISTICS PSRR 25 39 45 - dB Full 35 - - dB Input Noise Voltage (Note 2) 100kHz 25 - 14 - nV/√Hz Input Noise Current (Note 2) 100kHz 25 - 51 - pA/√Hz 25 - 10 40 µA Full - - 65 µA Input Resistance 25 25 50 - kΩ Input Capacitance 25 - 2 - pF 25 0.980 0.990 1.02 V/V Full 0.975 - 1.025 V/V 25 - 0.003 - % 25 3.0 3.3 - ±V Input Bias Current (Note 2) TRANSFER CHARACTERISTICS Gain VOUT = 2VP-P DC Non-Linearity (Note 2) ±2V Full Scale OUTPUT CHARACTERISTICS Output Voltage (Note 2) Full 2.5 3.0 - ±V 25, 85 50 60 - mA -40 35 50 - mA Supply Voltage Range Full 4.5 - 5.5 ±V Supply Current (Note 2) 25 - 21 26 mA Full - - 33 mA RL = 50Ω Output Current (Note 2) POWER SUPPLY CHARACTERISTICS AC CHARACTERISTICS -3dB Bandwidth (Note 2) VOUT = 0.2VP-P 25 - 750 - MHz Slew Rate VOUT = 5VP-P 25 - 1300 - V/µs Full Power Bandwidth (Note 2) VOUT = 4VP-P 25 - 150 - MHz Gain Flatness (Note 2) To 100MHz 25 - ±0.03 - dB To 30MHz 25 - ±0.01 - dB Linear Phase Deviation (Note 2) DC to 100MHz 25 - ±0.3 - ° 2nd Harmonic Distortion (Note 2) 50MHz, VOUT = 2VP-P 25 - -60 - dBc 3rd Harmonic Distortion (Note 2) 50MHz, VOUT = 2VP-P 25 - -80 - dBc 3rd Order Intercept (Note 2) 100MHz 25 - 30 - dBm 2 FN2944.8 June 6, 2006 HFA1110 VSUPPLY = ±5V, RL = 100Ω, Unless Otherwise Specified (Continued) Electrical Specifications TEMP (°C) MIN TYP MAX UNITS -1dB Gain Compression PARAMETER 100MHz TEST CONDITIONS 25 - 14 - dBm Reverse Gain (S12, Note 2) 100MHz, VOUT = 1VP-P 25 - -60 - dB TRANSIENT RESPONSE Rise Time VOUT = 0.5V Step 25 - 0.5 - ns Overshoot (Note 2) VOUT = 1.0V Step, Input Signal Rise/Fall = 1ns 25 - 2.5 - % 0.2% Settling Time (Note 2) VOUT = 1V to 0V 25 - 7 - ns 0.1% Settling Time (Note 2) VOUT = 1V to 0V 25 - 11 - ns 25 - 15 - ns Overdrive Recovery Time Differential Gain 3.58MHz, RL = 75Ω 25 - 0.04 - % Differential Phase 3.58MHz, RL = 75Ω 25 - 0.025 - ° NOTE: 2. See Typical Performance Curves for more information. Application Information 50Ω 0.1µF PC Board Layout The frequency performance of this amplifier depends a great deal on the amount of care taken in designing the PC board. The use of low inductance components such as chip resistors and chip capacitors is strongly recommended, while a solid ground plane is a must! Attention should be given to decoupling the power supplies. A large value (10µF) tantalum in parallel with a small value chip (0.1µF) capacitor works well in most cases. 1 +5V 10µF 2 3 IN 8 HFA1110 4 OUT RS 7 6 -5V 5 10µF 50Ω 0.1µF SCHEMATIC DIAGRAM BOTTOM LAYOUT Terminated microstrip signal lines are recommended at the input and output of the device. Output capacitance, such as that resulting from an improperly terminated transmission line will degrade the frequency response of the amplifier and may cause oscillations. In most cases, the oscillation can be avoided by placing a resistor (RS) in series with the output. See the “Recommended RS vs Load Capacitance” graph for specific recommendations. An example of a good high frequency layout is the Evaluation Board shown below. Evaluation Board An evaluation board is available for the HFA1110 (part number HFA1110EVAL). Please contact your local sales office for information. TOP LAYOUT The layout and schematic of the board are shown here: NOTE: The SOIC version may be evaluated in the DIP board by using a SOIC-to-DIP adapter such as Aries Electronics Part Number 08-350000-10. 3 1 FN2944.8 June 6, 2006 HFA1110 Typical Performance Curves VSUPPLY = ±5V, TA = 25°C, RL = 100Ω, Unless Otherwise Specified 1.2 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (mV) 120 80 40 0 -40 -80 -120 0.8 0.4 0 -0.4 -0.8 -1.2 TIME (5ns/DIV) TIME (5ns/DIV) FIGURE 1. SMALL SIGNAL PULSE RESPONSE FIGURE 2. LARGE SIGNAL PULSE RESPONSE 2 -45 -2 -90 -3 -135 -4 -180 PHASE VOUT = 200mVP-P -5 -6 RL = 100Ω 3 0 RL = 50Ω -3 -6 0 -225 -90 -270 -180 -7 -8 0 200M 400M 600M 800M 1M 1G -360 1G 100M FREQUENCY (Hz) FIGURE 3. FREQUENCY RESPONSE FIGURE 4. FREQUENCY RESPONSE FOR VARIOUS LOAD RESISTORS 890 1 870 BANDWIDTH (MHz) 0 -1 -2 VOUT = 200mVP-P VOUT = 2.5VP-P VOUT = 4VP-P -3 -4 -5 850 830 810 790 770 750 -6 730 -7 710 -8 10M FREQUENCY (Hz) 2 GAIN (dB) -270 RL = 1kΩ PHASE (°) 0 -1 GAIN (dB) GAIN (dB) 0 RL = 1kΩ 6 PHASE (°) GAIN VOUT = 200mVP-P VOUT = 1VP-P 1 1M 10M 100M FREQUENCY (Hz) 1G FIGURE 5. FREQUENCY RESPONSE FOR VARIOUS OUTPUT VOLTAGES 4 -50 -30 -10 10 30 50 70 90 110 130 TEMPERATURE (°C) FIGURE 6. -3dB BANDWIDTH vs TEMPERATURE FN2944.8 June 6, 2006 HFA1110 VSUPPLY = ±5V, TA = 25°C, RL = 100Ω, Unless Otherwise Specified (Continued) 0.25 2.0 0.20 1.5 0.15 1.0 DEVIATION (°) GAIN (dB) Typical Performance Curves 0.10 0.05 0 0.5 0 -0.5 -1.0 -0.05 -1.5 -0.10 -2.0 1M 10M FREQUENCY (Hz) 0 100M 200M 15M 30M 45M 60M 75M 90M 105M 120M 135M 150M FREQUENCY (Hz) FIGURE 7. GAIN FLATNESS FIGURE 8. DEVIATION FROM LINEAR PHASE -30 +90 PHASE GAIN -40 +45 0 -50 -60 INTERCEPT POINT (dBm) +135 PHASE (°) GAIN (dB) 50 -20 40 30 20 10 VOUT = 1VP-P 0 200M 400M 600M 800M 0 1G 0 50M 100M 150M 200M 250M 400M FIGURE 9. REVERSE GAIN AND PHASE (S12) FIGURE 10. TWO-TONE, THIRD ORDER INTERMODULATION INTERCEPT -30 -40 -40 100MHz -50 DISTORTION (dBc) DISTORTION (dBc) 350M FREQUENCY (Hz) -30 50MHz -60 -70 30MHz -80 100MHz -50 -60 -70 50MHz -80 30MHz -90 -90 -100 300M FREQUENCY (Hz) -100 -5 -3 -1 1 3 5 7 9 11 OUTPUT POWER (dBm) FIGURE 11. SECOND HARMONIC DISTORTION vs POUT 5 13 -5 -3 -1 1 3 5 7 9 11 13 OUTPUT POWER (dBm) FIGURE 12. THIRD HARMONIC DISTORTION vs POUT FN2944.8 June 6, 2006 HFA1110 Typical Performance Curves VSUPPLY = ±5V, TA = 25°C, RL = 100Ω, Unless Otherwise Specified (Continued) 0.8 0.4 0.2 0 -0.2 -0.4 RS (Ω) SETTLING ERROR (%) VOUT = 1V -0.8 -5 0 5 10 15 20 25 30 35 40 50 45 40 35 30 25 20 15 10 5 0 0 40 80 120 45 200 240 280 320 360 CL (pF) TIME (ns) FIGURE 13. SETTLING RESPONSE 160 FIGURE 14. RECOMMENDED SERIES OUTPUT RESISTOR vs CLOAD 0.04 21 RL = 200Ω 0.02 15 RL = 100Ω 12 VO = 2.0VP-P VO = 1.0VP-P 9 RL = 1kΩ ERROR (%) OVERSHOOT (%) 18 6 0 -0.02 VO = 0.5VP-P 3 0 200 300 400 500 600 700 800 900 -0.04 1000 -3.0 -2.0 -1.0 0 1.0 INPUT VOLTAGE (V) INPUT RISE TIME (ps) 3.0 FIGURE 16. INTEGRAL LINEARITY ERROR 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 25 24 SUPPLY CURRENT (mA) SUPPLY CURRENT (mA) FIGURE 15. OVERSHOOT vs INPUT RISETIME 2.0 23 22 21 20 19 18 17 5 6 7 8 9 TOTAL SUPPLY VOLTAGE (V+ - V-, V) FIGURE 17. SUPPLY CURRENT vs SUPPLY VOLTAGE 6 10 -60 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (°C) FIGURE 18. SUPPLY CURRENT vs TEMPERATURE FN2944.8 June 6, 2006 HFA1110 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 -60 VSUPPLY = ±5V, TA = 25°C, RL = 100Ω, Unless Otherwise Specified (Continued) 10 OUTPUT OFFSET VOLTAGE (mV) BIAS CURRENT (µA) Typical Performance Curves -40 -20 0 20 40 60 80 100 9.8 9.6 9.4 9.2 9 8.8 8.6 8.4 8.2 8 7.8 -60 120 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (°C) TEMPERATURE (°C) FIGURE 19. BIAS CURRENT vs TEMPERATURE FIGURE 20. OFFSET VOLTAGE vs TEMPERATURE 3.8 100 200 80 160 60 120 3.5 +VOUT (RL = 100Ω) 3.4 3.3 +VOUT (RL = 50Ω) |-VOUT |(RL = 100Ω) 3.2 3.1 |-VOUT |(RL = 50Ω) 3 40 80 INI 20 40 2.9 2.8 -60 NOISE CURRENT (pA/√Hz) 3.6 NOISE VOLTAGE (nV/√Hz) OUTPUT VOLTAGE (V) 3.7 ENI -40 -20 0 20 40 60 80 100 TEMPERATURE (°C) FIGURE 21. OUTPUT VOLTAGE vs TEMPERATURE 7 120 0 100 1k 10k 0 100k FREQUENCY (Hz) FIGURE 22. INPUT NOISE vs FREQUENCY FN2944.8 June 6, 2006 HFA1110 Die Characteristics DIE DIMENSIONS: PASSIVATION: 63 mils x 44 mils x 19 mils 1600µm x 1130µm x 483µm Type: Nitride Thickness: 4kÅ ±0.5kÅ METALLIZATION: TRANSISTOR COUNT: Type: Metal 1: AlCu(2%)/TiW Thickness: Metal 1: 8kÅ ±0.4kÅ Type: Metal 2: AlCu(2%) Thickness: Metal 2: 16kÅ ±0.8kÅ 52 SUBSTRATE POTENTIAL (POWERED UP): Floating (Recommend Connection to V-) Metallization Mask Layout HFA1110 NC IN V- NC NC NC NC V+ OUT 8 FN2944.8 June 6, 2006 HFA1110 Small Outline Plastic Packages (SOIC) M8.15 (JEDEC MS-012-AA ISSUE C) N 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE INDEX AREA 0.25(0.010) M H B M INCHES E SYMBOL -B- 1 2 3 L SEATING PLANE -A- A D h x 45° -C- e A1 B 0.25(0.010) M C 0.10(0.004) C A M MIN MAX MIN MAX NOTES A 0.0532 0.0688 1.35 1.75 - A1 0.0040 0.0098 0.10 0.25 - B 0.013 0.020 0.33 0.51 9 C 0.0075 0.0098 0.19 0.25 - D 0.1890 0.1968 4.80 5.00 3 E 0.1497 0.1574 3.80 4.00 4 e α B S 0.050 BSC 1.27 BSC - H 0.2284 0.2440 5.80 6.20 - h 0.0099 0.0196 0.25 0.50 5 L 0.016 0.050 0.40 1.27 6 N α NOTES: MILLIMETERS 8 0° 8 8° 0° 7 8° 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. Rev. 1 6/05 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 9 FN2944.8 June 6, 2006